You are on page 1of 63

NATIONAL AERONAUTICS AND SPACE ADMINISTRATION

SPACE SHUTTLE
MISSION
STS-5
PRESS KIT
OCTOBER 1982

FIRST OPERATIONAL FLIGHT

Edited by Richard W. Orloff, 01/2001/Page 1


STS-5 INSIGNIA
S82-35627 -- The five points of the star in the STS-5 insignia represent the fifth, and first operational shuttle flight
following four successful test flights.

The NASA insignia design for space shuttle flights is reserved for use by the astronauts and for other official use as
the NASA Administrator may authorize. Public availability has been approved only in the form of illustrations by
the various news media. When and if there is any change in this policy, which we do not anticipate, it will be
publicly announced.

PHOTO CREDIT: NASA or National Aeronautics and Space Administration.

Edited by Richard W. Orloff, 01/2001/Page 2


RELEASE NO: 82-156 October 1982

CONTACTS
Jim Kukowski
Headquarters, Washington, D.C.
(Phone: 202/ 755- 3090)

Dick Young
Kennedy Space Center, Fla.
(Phone: 305/867-2468)

Terry White
Johnson Space Center, Houston, Texas
(Phone: 713/483-5111)

John Taylor
Marshall Space Flight Center, Ala.
(Phone: 2115/453- 0034 )

Ralph B. Jackson
Dryden Flight Research Facility, Edwards, Calif.
(Phone: 805/258-8381

Edited by Richard W. Orloff, 01/2001/Page 3


CONTENTS
GENERAL RELEASE 5

PRESS BRIEFING SCHEDULE 7

NASA SELECT TELEVISION SCHEDULE 8

LAUNCH PREPARATIONS, COUNTDOWN AND LIFTOFF 11

MAJOR COUNTDOWN MILESTONES 13

LAUNCH WINDOW 14

FLIGHT SEQUENCE OF EVENTS 14

FLIGHT PLAN 15

IF THINGS GO WRONG 27

CONFIGURATION 28

EXTRAVEHICULAR ACTIVITY 30

DEPLOYMENT OF SBS-3 AND ANIK C-3 35

SBS-3 35

ANIK C-3 39

FLIGHT EXPERIMENTS 40
Student Involvement Program 40
Getaway Special 41
Orbiter Experiments Program 42
Glow Experiment 44
Oxygen Atom Interaction With Materials Test 45
Development Flight Instrumentation

LANDING OPPORTUNITIES FOR NASA DRYDEN 47

LANDING AND POSTLANDING OPERATIONS 52

SPACEFLIGHT TRACKING AND DATA NETWORK 54

NASA TRACKING STATIONS 54

HUNTSVILLE OPERATIONS SUPPORT CENTER 55

CREW BIOGRAPHIES 56

SPACE SHUTTLE PROGRAM MANAGEMENT 61

Edited by Richard W. Orloff, 01/2001/Page 4


RELEASE NO: 82-156 October 22, 1982

STS-5 FEATURES LAUNCH OF TWO COMMERCIAL SATELLITES


AND SPACE WALK
The fifth flight of the Space Shuttle marks the first operational use of the nation's Space Transportation System.
Spaceship Columbia's first operational job will be to haul two commercial communications satellites -- Satellite
Business System's SBS-3 and Telesat Canada's Anik C-3 into orbit.

Designated STS-5, the fifth Shuttle mission is scheduled for launch on Nov. 11, 1982 from Complex 39's Pad A at
NASA's Kennedy Space Center, Fla. Launch of STS-5 is set for 7:19 a.m. EST.

Significant "firsts" for Columbia on STS-5 will include:

x First Space Shuttle flight to carry and deploy commercial satellites into space.

x First flight with a crew of four astronauts.

x First flight of Mission Specialists aboard the Space Shuttle.

x First planned "space walk" to demonstrate the Extravehicular Mobility Units.

The flight crew for STS-5 is comprised of Commander Vance Brand, 51, and Robert Overmyer, 46, pilot. Mission
specialists are Dr. William B. Lenoir, 43, and Dr. Joseph Allen, 45.

As part of their chores, the mission specialists will perform the first Extravehicular Activity (EVA) ever attempted
on a Shuttle flight. The two mission specialists will go out together into the Columbia's cargo bay where they will
spend more than three hours testing their space suits' cooling and communications systems, and practicing
procedures that may be used to repair an orbiting satellite, conduct a space walk to close balky bay doors or repair
thermal protection tiles on the orbiter's exterior.

Columbia will be launched into a 185-statute-mile (160 nautical-mile) circular orbit above the earth with an
inclination to the equator of 28.5 degrees. Space Shuttle main engines will be run at 100 percent of their rated power
level.

The launch window will open at 7:19 a.m. and close at 7:59 a.m. EST. The shortness of the window is due to
daylight landing constraints at Edwards Air Force Base, Calif., as well as contingency landing sites, and to obtain
the proper sun angle for the two commercial satellites after they are deployed and relying on their solar cells for
electrical power.

Mission duration is 5 days, 2 hours and 9 minutes, with landing to occur on Nov. 16 at 9:27 a.m. EST. Columbia
will again aim for a lakebed landing at Edwards Air Force Base.

The principal cargo to be carried on STS-5 is two commercial communications satellites. Other items to be carried
in the cargo bay will be a Getaway Special (GAS) canister and the Development Flight Instrumentation (DFI)
package. Experiments scheduled to fly in the orbiter's mid-deck include three Shuttle Student Involvement Project
experiments. The Remote Manipulator Arm has been removed for STS-5.

Satellite Business Systems' SBS-3 is the third in a series of business communications satellites, while Telesat
Canada's Anik C-3 is the fifth of a series of satellites that provides domestic communications services for Canada.

STS-5 will mark the first use of the Shuttle Payload Assist Module, PAM-D, and a new ejection system. A modified
version of the Payload Assist Module has been used as the third stage of NASA's Delta rocket to propel a variety of
satellites to geosynchronous altitude.

Edited by Richard W. Orloff, 01/2001/Page 5


SBS-3 will be the first spacecraft launched out of the cargo bay. It will be deployed on the sixth orbit, about eight
hours after liftoff, when the orbiter is over the Atlantic Ocean. The Anik C-3 spacecraft will be released on the
second day of the mission, on about orbit 22, while Columbia is over the Pacific Ocean near Hawaii.

At the beginning of their fourth day in orbit, Allen and Lenoir will don pressure suits -- Extravehicular Mobility
Units (EMU) -- and backpacks with portable life support systems to perform the extravehicular activity.

They will inspect the cargo bay and then move to a stationary tool box and remove a mini work station that will
tether them at various worksites.

In view of the payload bay cameras, they will test stationary and portable foot restraints, torque and box wrenches,
scissors, cutters and ratchet tools to be used on future flights. They will also test two winches mounted on the
forward and aft bulkheads.

The Getaway Special experiment will use X-Ray recordings to investigate the behavior of metallic dispersions. It is
the first in a series of material science experiments conducted by the German Ministry of Research and Technology.

Columbia will operate in several different attitudes during the 122-hour flight to obtain additional information on
the thermal characteristics of the spacecraft.

During the mission, Columbia will spend about 40 hours with its side turned to the sun, and another 20 hours facing
the sun with its nose propped up about 10 degrees and about 10 hours rolling wing-over-wing in a barbecue fashion
known as Passive Thermal Control mode.

This maneuver is performed for short periods of time throughout the mission to even out temperatures over the
entire spaceship.

As a result of the STS-4 solid rocket boosters' deceleration system failure, on this mission the parachute disconnect-
at-water-impact feature has been removed. The feature was intended to prevent the possibility of partially inflated
parachute canopies dragging the boosters through the water after impact. It was active on STS-1, 2 and 3 but was
partially removed for STS-4. For that flight the frangible nuts holding one of two risers for each main parachute
were replaced by regular, solid nuts which would not separate that riser. For STS-5 the remaining frangible nuts will
be replaced with solid hardware. As a result, both risers on each parachute will now remain attached to the boosters
until they can be detached by the retrieval crew.

Entry will follow the same course in returning from orbit as did earlier STS missions: retrofire over the Indian
Ocean, atmosphere entry over the western Pacific Ocean, transition to aerodynamic controls in the atmosphere and
the landing as an aircraft.

Plans call for the first attempt at a fully automated landing of the orbiter on the dry lakebed at Edwards Air Force
Base. The crew will closely monitor the "hands off" approach and landing and be ready to take over manual control,
if necessary. The chance for a crosswind landing, a desired landing mode, is not likely due to the calm wind
conditions expected in the early morning hours.

(END OF GENERAL RELEASE; BACKGROUND INFORMATION FOLLOWS.)

Edited by Richard W. Orloff, 01/2001/Page 6


STS-5 PRESS BRIEFING SCHEDULE

Date Time EDT Time CDT Time PDT Event Origin

T-2 9:00 a.m. 8:00 a.m. 6:00 a.m. STS-5 Countdown Status KSC
10:00 a.m. 9:00 a.m. 7:00 a.m. Flight Plan & EVA
1:00 p.m. 12:00 p.m. 10:00 a.m. SBS-3/Anik C-3 and Experiments KSC

T-1 9:00 a.m. 8:00 a.m. 6:00 a.m. Countdown Status KSC
10:30 a.m. 9:30 a.m. 7:30 a.m. Prelaunch Press Conference KSC

T-0 (Approx. 90 mins Post Launch Press Conference KSC


after launch)

T thru T+5 See TV Schedule Flight Director's Change of Shift JSC


Briefings

T+6 (Approx 2 hours Post Landing Briefing DFRF


after landing)

T+7 2:00 p.m. 1:00 p.m. 11:00 a.m. Orbiter Status Briefing DFRF

Edited by Richard W. Orloff, 01/2001/Page 7


*******************************************************************************************

JSC NASA SELECT TELEVISION SCHEDULE for STS-5


REVISED- 10/18/82
**********************************PRE-LAUNCH ACTIVITIES*********************************

T MINUS 2 DAYS - Countdown Status Briefing from KSC 9:00 AM EST


-Flight Plan/EVA Briefing 10:00 AM EST
- SBS/Anik/Experiments Briefing 1:00 PM EST

T MINUS 1 DAY - Countdown Status Briefing from KSC 9:00 AM EST


- Pre-Launch Press Conference from KSC 10:30 AM EST

---------------------------- Thursday, November 11 --------------------------

MET
ORBIT SUBJECT (DD/HH:MM) EST
LAUNCH 7:19 AM
OTV LAUNCH VIDEO from KSC 00/00:45-01:00 7:04 AM
2 GROUND CONTROLLED PAYLOAD BAY TV (MIL) 00/01:36-01:45 8:55 AM
T = 9:04
2 PLAYBACK of GROUND CONTROLLED PAYLOAD 00/01:56 9:15 AM
BAY TV
4 SHIFT BRIEFING-ASCENT/ENTRY 00/05:00 12:20 PM
TOMMY HOLLOWAY-FLIGHT DIRECTOR
6 TV01 SBS PRE-DEPLOY ACTIVITIES (HAW) 00/07:41-07:49 3:00 PM
T = 8: O 8
6 PLAYBACK of TV01 SBS PRE-DEPLOY ACTIVITIES 00/08:01 3:20 PM
7 TV01 VTR DUMP of SBS DEPLOY (HAW) 00/09:17 4:36 PM
T=7:41
7 PLAYBACK of SBS DEPLOY 00/09:36 4:55 PM
9 SHIFT BRIEFING-ORBIT 00/12:30 7:50 PM
JOHN COX-FLIGHT DIRECTOR

----------------------------- Friday, November 12 ---------------------------

14 SHIFT BRIEFING-PLANNING 00/20:30 3:50 AM


GARY COEN-FLIGHT DIRECTOR
19 SHIFT BRIEFING-ASCENT/ENTRY 01/03:30 10:50 AM
TOMMY HOLLOWAY-FLIGHT DIRECTOR
22 TVO2 ANIK PRE-DEPLOY ACTIVITIES (HAW) 01/07:50 3:09 PM
T=8: 12
22 PLAYBACK of ANIK PRE-DEPLOY ACTIVITIES 01/08:11 3:30 PM
24 SHIFT BRIEFING-ORBIT 01/11:30 6:50 PM
JOHN COX-FLIGHT DIRECTOR

Edited by Richard W. Orloff, 01/2001/Page 8


---------------------------- Saturday, November 13 --------------------------

ORBIT SUBJECT MET


(DD/HH:MM) EST
30 SHIFT BRIEFING-PLANNING 01/19:30 2:50 AM
GARY COEN-FLIGHT DIRECTOR

32 TVO2 VTR DUMP of ANIK DEPLOY (GDS) 01/22:38 5:57 AM


(MIL) 01/22:42
T=2 :49/6:33
32 PLAYBACK of ANIK DEPLOY 01/23:01 6:20 AM
34 SHIFT BRIEFING-ASCENT/ENTRY 02/02:30 9:50 AM
TOMMY HOLLOWAY- FLIGHT DIRECTOR
38 WATER DUMP/AIRLOCK EQUIPMENT PREP (HAW) 02/08:00 3:19 PM
T=7: 56
38 PLAYBACK of AIRLOCK EQUIPMENT PREPARATION 02/08:21 3:40 PM
39 SHIFT BRIEFING-ORBIT 02/10:00 5:20 PM
JOHN COX-FLIGHT DIRECTOR

----------------------------- Sunday, November 14 ---------------------------

46 SHIFT BRIEFING-PLANNING 02/20:30 3:50 AM


GARY COEN-FLIGHT DIRECTOR

49 TV05 EVA (GDS) 03/00:20 7:39 AM


SCHEDULED TIME of EGRESS (MIL) 03/00:27
T=6:19/8:41
49 PLAYBACK of EVA from ORBIT 49 03/00:46 8:05 AM
50 TV05 EVA (HAW) 03/01:44 9:03 AM
(GDS) 03/01:55
(MIL) 03 /02:04
T=8:04/5:56/6:04
50 PLAYBACK of TV05 EVA 03/02:21 9:40 AM
51 TV05 EVA (HAW) 03/03:20 10:39 AM
(GDS) 03 /03:31
T=7:34/3:49
51 PLAYBACK of TV05 EVA 03/03:46 11:05 AM
53 SHIFT BRIEFING-ASCENT/ENTRY 03/05:45 1:05 PM
TOMMY HOLLOWAY-FLIGHT DIRECTOR
57 SHIFT BRIEFING-ORBIT 03/11:30 6:50 PM
JOHN COX-FLIGHT DIRECTOR

Edited by Richard W. Orloff, 01/2001/Page 9


---------------------------- Monday, November 15 ----------------------------

MET
ORBIT SUBJECT (DD/HH:MM) EST
62 SHIFT BRIEFING-PLANNING 03/19:00 2:20 AM
GARY COEN-FLIGHT DIRECTOR
65 TV06 STUDENT EXPERIMENTS
FLUID CONVECTION in ZERO G (HAW) 04/00:08 7:27 AM
CRYSTAL GROWTH (GDS) 04 /00:19 7:38 AM
PORIFERA INTERCELLULAR
COMMUNICATIONS (MIL) 04 /00:26 7:45 AM
T=7:49/5:48/8:11
65 PLAYBACK of TV06 STUDENT EXPERIMENTS 04/00:46 8:05 AM
66 SHIFT BRIEFING-ASCENT/ENTRY 04/01:30 8:50 AM
TOMMY HOLLOWAY-FLIGHT DIRECTOR
72 SHIFT BRIEFING-ORBIT 04/10:00 5:20 PM
JOHN COX - FLIGHT DIRECTOR

---------------------------- Tuesday, November 16 ---------------------------

79 SHIFT BRIEFING-PLANNING 04/19:30 2:50 AM


GARY COEN-FLIGHT DIRECTOR

82 LANDING 05/02:09 9:28 AM

****----------------------- POST LANDING ACTIVITIES ----------------------****

LANDING plus APPROX. 2 Hours - Post Landing Briefing from DFRF

LANDING plus ONE Day - Orbiter Status Briefing from DFRF 2:00 PM

Definition of Terms
MET: Mission Elapsed Time. The time which begins at the moment of launch. Read the clock by Days/Hours: Minutes.
CST: Central Standard Time.
ORBIT: The number of revolutions made by the spacecraft over a specific point on the Earth.
T=: Total time. In this case it will refer to the total time of the television pass.
EVA: Extravehicular Activity

Tracking Stations
GDS: Goldstone, California
HAW: Hawaii
MIL: Merritt Island Launch Area, Fla.

Payloads
SBS: Satellite Business Systems.
ANIK: A Telesat Ltd. of Canada owned satellite.

Edited by Richard W. Orloff, 01/2001/Page 10


LAUNCH PREPARATIONS, COUNTDOWN AND LIFTOFF
The Shuttle Orbiter Columbia arrived at Kennedy Space Center from California atop its 747 jumbo carrier aircraft
on July 15, the same day that stacking began on the twin solid rocket boosters that will help launch Columbia on its
fifth flight.

The Satellite Business Systems' SBS-3 and Telesat Canada's Anik C-3 spacecraft both arrived by aircraft at the Skid
Strip on Cape Canaveral Air Force Station on July 20.

Stacking of the twin solid rocket boosters on the deck of Mobile Launcher Platform-1 was completed on Aug. 16
and the massive 47-meter (154-foot) tall external tank was mated with the booster rockets on Aug. 20.

Modifications to Columbia in the processing hangar were primarily to support the first four-man crew and
commercial satellites. The Remote Manipulator Arm and the Induced Environmental Contamination Monitor were
taken out of the payload bay and the ejection seats were deactivated.

Columbia was moved to the Vehicle Assembly Building on Sept. 9 and was attached to its external tank and booster
rockets on Sept. 10.

Another milestone achieved Sept. 10 was the transfer of the Anik C-3 satellite from Area 60 to the Vertical
Processing Facility where the individual satellites are integrated into a single Shuttle cargo.

A Shuttle Interface Test was conducted from Sept. 13-16 to verify the mechanical, fluid and electrical connections
between the orbiter and its external tank and booster rockets. The test ended on Sept. 16 with a successful mock
launch and reentry of the Shuttle with two of the four STS-5 crewmen - Commander Vance Brand and Pilot Robert
Overmyer -- at the controls of the spaceship.

The Space Shuttle was moved to Pad A of Complex 39 on Sept. 21 to undergo final checkout and propellant
servicing for launch. Pad to vehicle connections were completed on Sept. 22.

SBS-3 satellite was delivered to the Vertical Processing Facility Sept. 22.

A Terminal Countdown Demonstration Test with the STS-5 flight crew was conducted Sept. 24 to establish a
timeline for activities involving the flight crew.

Integrated testing of the STS-5 cargo began Sept. 27 using special test equipment, called Cargo Integration Test
Equipment, or CITE.

A series of CITE tests, lasting more than a week, was conducted to check orbiter-to-cargo interface points, simulate
the deployment sequence and verify the communications link between the cargo and the Payload Operations
Control Center in Houston.

An Integrated Cryogenic Loading Test was conducted on Sept. 28 to check the integrity of the external tank's outer
insulation, verify the loading sequence and test the ability of Shuttle components to function properly in the super-
cold environment. The No. 3 Auxiliary Power Unit that was replaced in the Orbiter Processing Facility was
successfully test fired at the conclusion of the propellant loading test.

Preflight servicing of Columbia with hypergolic propellants was conducted from Oct. 5-8.

The STS-5 cargo was placed in an environmentally-controlled transport canister and taken to Pad A on Oct. 12.

Functional checks were run of each spacecraft in the Payload Changeout Room before the cargo was put inside
Columbia's payload bay on Oct. 18. Electrical tests were conducted to make sure the cargo was properly connected
to the orbiter, followed by interface checks with Mission Control and the Payload Operations Control Center.

Edited by Richard W. Orloff, 01/2001/Page 11


Countdown preparations were scheduled to begin Oct. 29, leading to a pick up of the 100-hour Shuttle Launch
Countdown on Nov. 7.

The launch countdown for STS-5 will be conducted from Firing Room 1 of the Launch Control Center by a
government/industry team of about 200 persons.

The STS-5 launch countdown contains 80 hours of actual count time and 20 hours, 19 minutes of planned hold
time.

The major change in the STS-5 countdown will be the later retraction of the protective Rotating Service Structure at
the end of a planned 10 hour and 59 minute hold, or approximately 10 and one-half hours before liftoff.

The terminal portion of the countdown will start at the T-6 hour mark with the loading of cryogenic propellants into
the external tank

At T-9 minutes, the automatic ground launch sequencer will take command of the countdown, issuing critical
commands and maintaining a cutoff capability until liftoff.

Edited by Richard W. Orloff, 01/2001/Page 12


MAJOR COUNTDOWN MILESTONES

Count Time Event


T-80 hrs Call to stations.
T-68 hrs Pressurize maneuvering and reaction control system propellant tanks.
T-40 hrs Load cryogenics into orbiter fuel cell supply tanks and pressurize.
T-34 hrs Eight hour built-in hold.
T-24 hrs Start external tank loading preparations.
T-17 hrs Perform interface check with Mission Control.
T-9 hrs, 15 mins Ten-hour 59-minute built-in hold.
T-9 hrs, 15 mins Retract Rotating Service Structure.
(counting)
T-6 hrs Start cryogenic propellant chilldown and load. Activate fuel cells and begin load sharing.
T-3 hrs 1 hour built-in hold.
T-3 hrs (holding) Wake flight crew (Launch -4 hours, 10 minutes).
T-2 hrs, 40 mins Suit flight crew (Launch -3 hours).
T-2 hrs, 30 mins Crew departs for pad (Launch -2 hours, 50 minutes).
T-1 hour, 55 mins Start crew entry (Launch -2 hours, 15 minutes).
T-61 mins Inertial Measurement Unit begins preflight alignment.
T-20 mins 10-minute built-in hold.
T-20 mins (holding) Orbiter computers configure for launch.
T-20 mins Orbiter computers transition to launch configuration.
T-9 mins 10-minute built-in hold. Status check and Launch Director “go”.
T-9 mins (counting). Start ground launch sequencer
T-7 mins Retract orbiter access arm.
T-5 mins Start orbiter auxiliary power units and arm external tank and solid rocket booster
ignition and range safety systems.
T-3 mins, 30 secs Orbiter goes on internal power.
T-2 mins, 55 secs Pressurize liquid oxygen tank and retract gaseous oxygen vent hood.
T-1 min, 57 secs Pressurize liquid hydrogen tank.
T-28 secs Orbiter computers start launch sequence. Start solid rocket booster hydraulic units.
T-6 .8 secs Go for main engine start.
T-3 secs Main engines at 90 percent thrust.
T-0 Solid rocket booster ignition, holddown post release and liftoff.
T+7 secs Tower clear, control switches to Mission Control.

Edited by Richard W. Orloff, 01/2001/Page 13


LAUNCH WINDOW
STS-5 will be launched from Complex 39's Pad A at Kennedy Space Center no earlier than Nov. 11, 1982. The
launch window on that date extends from 7:19 a.m. to 7:59 a.m. EST, for a launch opportunity of 40 minutes in
duration.

The shortness of this launch window, compared to previous launch windows, is due to a daylight landing constraint
at Edwards, as well as the contingency landing sites, and to obtain the proper orbital positioning for deploying the
two commercial satellites on the first and second days of the mission.

The window assumes a nominal landing on a dry lake bed at Edwards Air Force Base. Calif.

STS-5 will be launched into a 160 nautical mile (185 statute mile) circular orbit with an inclination to the equator of
28.5 degrees.

STS-5 FLIGHT SEQUENCE OF EVENTS

Mission Elapsed
Time
Event (d:h:m:s) Comments

SRB ignition/liftoff 0/00:00:00


Pitchover 0/00:00:08
Max Q 0/00:01:07 675 lbs/ft2
SRB separation 0/00:02:07 158,077 ft alt, 28 nm downrange
MECO 0/00:08:35 57 nm alt, 763 nm downrange
ET separation 0/00:08:56
OMS-1 burn 0/00:10:38 241 fps, 51.5x160 nm orbit
OMS-2 burn 0/00:44:48 194 fps, 160x160 nm orbit
SBS separation burn 1/00:13:25 16 fps, 169x160 nm orbit
Recircularization 1 1/00:47:00 1.8 fps, 167x160 nm orbit
Recircularization 2 1/00:51:00 12.3 fps, 160x160 nm orbit
Telesat separation burn 1/08:21:20 16 fps, 160x169 nm orbit
RCS orbit adjust 2/20:58:00 32 fps, 145x164 nm orbit
RCS orbit adjust (Five 30-second
burns 30 minutes apart) 3/05:26:27 55 fps, 139x152 nm orbit
Deorbit ignition 5/01:12:00 261 fps, -2x151 nm entry orbit
Entry interface (400 K ft) 5/01:39:00
Landing 5/02:09:00

Edited by Richard W. Orloff, 01/2001/Page 14


GUIDE TO USING THE FLIGHT PLAN
Summary Level Timeline (12-hour time span)

a. Timescales: Two time references are presented in this section. The two time references used are Central
Daylight Time (CDT) (or TIG minus) and Mission Elapsed Time (MET). MET is referenced to liftoff
beginning at 00/00:00:00 (days, hours, minutes and seconds).

b. Crewmen (CDR, PLT, MS-1, MS-2): This is the column where titles of scheduled activities are shown for
the commander (CDR), pilot (PLT), and mission specialist (MS-1, MSA-2) at the appropriate times.

c. Day/Night and orbit:

1) Day/Night - The orbital day/night intervals are shown by black bars when the orbiter is in darkness.

2) Orbit - Indicates which orbit the spacecraft is in by numerical sequence. The beginning of an orbit
occurs when the orbiter crosses the Earth's equator going from the southern to the northern hemisphere
(ascending node). The succession of orbits is numbered in this column starting with orbit 1 for launch.

d. Earth Trace W/SAA: This is a display of the groundtrack of the orbiter and when it passes over the South
Atlantic Anomaly (SAA) (indicated by a ' ---- ').

e. GSTDN Coverage: The GSTDN communication coverage periods are indicated in this area with a
horizontal line indicating when communication is available; the GSTDN site is identified to the right of the
line.

f. Deorbit OPT: Times are identified in this area when deorbit burn opportunities exist for Edwards AFB
(EDW) and Kennedy Space Center (KSC).

g. Attitudes and Maneuvers:

1) Attitude - The current attitude of the vehicle is identified in this area, i.e., PTC, Nose to Sun.

2) Maneuvers - An ` ‘ is placed at the time an attitude maneuver occurs if the duration in attitude is to be
greater than 15 minutes.

h. VTR: Indicates periods when the video tape recorder is running (indicated by a ‘----’). TV - TV is
indicated in this area with a ‘----’.

i. Payload operating periods.

Edited by Richard W. Orloff, 01/2001/Page 15


Edited by Richard W. Orloff, 01/2001/Page 16
Edited by Richard W. Orloff, 01/2001/Page 17
Edited by Richard W. Orloff, 01/2001/Page 18
Edited by Richard W. Orloff, 01/2001/Page 19
Edited by Richard W. Orloff, 01/2001/Page 20
Edited by Richard W. Orloff, 01/2001/Page 21
Edited by Richard W. Orloff, 01/2001/Page 22
Edited by Richard W. Orloff, 01/2001/Page 23
Edited by Richard W. Orloff, 01/2001/Page 24
Edited by Richard W. Orloff, 01/2001/Page 25
Edited by Richard W. Orloff, 01/2001/Page 26
IF THINGS GO WRONG
All methods of aborting the Space Shuttle launch are aimed toward safe and intact recovery of the orbiter and its
payloads. Flight crews and Mission Control Center-Houston flight controller teams train extensively for an abort
situation everyone hopes will never happen.

The abort-to-orbit (ATO) is the preferred type of abort. This would follow loss of one main engine near the end of
mainstage flight in which the orbital maneuvering engines (OMS) could provide enough additional boost to reach a
minimal 194-km (105 nm) orbit and still leave enough OMS fuel for the deorbit burn.

Earlier shutdown of one main engine or a major orbiter systems failure after orbital insertion calls for an abort-once-
around (AOA) in which Columbia would land at White Sands Missile Range, N.M., at the end of one orbit. Loss of
two engines midway through powered flight forces a trans-Atlantic abort landing (TAL) into Dakar, Senegal. Dakar
is the first landfall for orbiters launched into 28.5-degree inclination orbits, as are STS-4 through STS-8 and STS-11
through STS-15. The transatlantic abort landing site for STS-1, 2 and 3 was Rota, Spain.

Early shutdown of one or more engines calls for a return-to-launch-site abort (RTLS). After an abort decision,
Columbia would be flown in a pitch-around maneuver to heads-up and pointed back along the ground track to
Kennedy Space Center. Whatever main engine thrust still available would then be used to kill off eastward velocity,
until westward motion would get Columbia within gliding distance of the Kennedy runway.

STS-5 contingency landing sites are Kennedy; Edwards Air Force Base, Calif.; White Sands Missile Range, N.M.;
Hickam Air Force Base/Honolulu International Airport, Hawaii; Kadena Air Base. Okinawa; Dakar, Senegal, and
Rota, Spain.

Edited by Richard W. Orloff, 01/2001/Page 27


CONFIGURATION
READYING COLUMBIA FOR ITS FIRST COMMERCIAL CARGO FLIGHT

For STS-5, pyrotechnics have been removed from the two flight deck ejection seats and two mission specialist seats
have been installed -- one on the aft flight deck and one on the middeck. The ejection seats and their rails will
eventually be removed from Columbia along with other major modifications at Palmdale, Calif., after STS-
9/Spacelab 1. Currently it is planned to modify Columbia to carry the European Space Agency (ESA) Spacelab on
STS-9. Challenger will fly STS-6, 7 and 8.

The payload deployment and retrieval system, or remote manipulator arm, has been removed for STS-5 for a weight
savings of 447 kilograms (985 pounds).

The remote arm will be installed only on flights calling for its use. In addition to the SBS-3 and Anik C-3
communications satellites and their cradle fixtures, the developmental flight instrumentation (DFI) package and the
Getaway Special canister occupy the payload bay.

The STS-5 vehicle will weigh 2,035,976 kg (4,488,559 lb.) at solid rocket booster ignition.

Edited by Richard W. Orloff, 01/2001/Page 28


Edited by Richard W. Orloff, 01/2001/Page 29
EXTRAVEHICULAR ACTIVITY
FIRST SHUTTLE SPACEWALK TESTS SPACE REPAIR TECHNIQUES

STS-5 mission specialists Dr. William Lenoir and Dr. Joseph Allen will don the new-generation Shuttle spacesuits
early on Nov. 14 and go through the airlock into Columbia's payload bay. For approximately three and a half hours,
Lenoir and Allen will evaluate the spacesuit on its first outing in space and also test prototype space tool and repair
devices. Some of the tools will be used to work on a simulated black box on the work station. The box is similar to a
panel box on the ailing Solar Maximum Mission satellite. A repair mission to the satellite, including a satellite
capture and extravehicular activity, is tentatively scheduled for STS-13.

Lenoir and Allen will be the first American astronauts to go outside their spacecraft since Feb. 3, 1974, when
Skylab 4 commander Jerry Carr and science pilot Dr. Ed Gibson spent five hours 19 minutes retrieving film
canisters from the space station’s solar observatory.

Spacesuits have been stowed aboard Columbia on all four orbital test flights for possible emergency closing of the
payload bay doors, but the STS-5 extravehicular activity or spacewalk is the first planned on the Shuttle program.
Earlier it was planned to depressurize Columbia's cabin from 14.7 pounds per square inch (psi) to 10.2 psi for some
12 hours prior to an EVA to allow denitrogenization of crewmen's bloodstreams.

For STS-5, Lenoir and Allen will prebreathe 100 percent oxygen in the spacesuits for three and a half hours in the
airlock to wash nitrogen from their bloodstreams. The airlock will then be depressurized to 5 psi for spacesuit leak
checks before going all the way to space vacuum. After the airlock hatch is opened, both men will attach themselves
to safety tethers clipped to slidewires running aft along the payload bay door hingelines.

Lenoir will move toward the aft bulkhead along the starboard (right) slidewire while Allen monitors his motion.
Allen then moves along the port slidewire to join Lenoir at the aft bulkhead. Enroute, both men evaluate translation
rates, handholds and safety tethers, spacesuit communications and television, floodlighting in the payload bay and
potential work sites for contingency extravehicular activities.

A miniature black-and-white television camera atop Allen's space helmet will also be evaluated as an aid.

Both crewmen are back at the forward bulkhead an hour and 20 minutes after extravehicular start to conduct a series
of tests with tools and devices at the work station mounted on the starboard side of the payload bay. For an hour, the
two will make torque measurements on fixed and torsion-adjustable bolts with a wrench that measures torque from
zero to 600 inch-pounds.

Measurements will be voiced to Brand and Overmyer in the aft deck for recording. These measurements are aimed
at correlating actual inflight torque forces for ground simulations in one gravity and in the Johnson Weightless
Environment Test Facility (WETF).

For what will be the most complex task in the space walk, Lenoir will overhaul a mockup Solar Maximum Mission
satellite coronagraph main electronics box (MEB) on the work station while Allen hands him tools. With
pressurized spacesuit gloves, he will remove a thermal blanket, back out mounting bolts, demate cable connectors,
cut a grounding strap and remate the connectors -- all hardware not designed for inflight space maintenance or
repair. Among the tools used by Lenoir will be one designed for possible use in Space Telescope extravehicular
activity operations.

Allen will next operate the winch on the forward bulkhead that is intended for contingency payload bay door
closing. The winch line will wind through a series of pulleys to a "Sky-Genie" variable-friction device adjusted to
about 45 kg (100 lb.) tension. Allen will crank the winch both with and without foot restraints to measure a
crewman's capability to apply manual loads to such devices. The winch tasks, to which 30 minutes have been
allotted, also demonstrate handling rope in zero-gravity.

Edited by Richard W. Orloff, 01/2001/Page 30


The final extravehicular activity task before crawling back into the airlock will be a 15-minute "translation with a
large mass" in which Allen carries a 27-kg (60-lb.) bag of latch tools across the forward bulkhead and part-way
down the hingeline slidewire.

Allen and Lenoir have a shopping list of additional extravehicular activity tasks if time permits, including
evaluation of tape, Velcro and thermal gloves from the toolbox, installing a payload retention device between a
bulkhead handrail and the work station, removing from the work station an "extravehicular activity bolt", similar to
those in the payload bay door drive mechanism and installing a bulkhead latch tool at the work station.

After stowing tools and equipment in the payload bay, the two men will enter the airlock, repressurize to 5 psi, and
switch the spacesuit life support and communications back to orbiter internal power before equalizing airlock
pressure with cabin pressure. The life support backpacks are then recharged after Allen and Lenoir doff the
spacesuits.

Edited by Richard W. Orloff, 01/2001/Page 31


Edited by Richard W. Orloff, 01/2001/Page 32
Edited by Richard W. Orloff, 01/2001/Page 33
Edited by Richard W. Orloff, 01/2001/Page 34
DEPLOYMENT OF SBS-3 AND ANIK C-3
SBS-3 and Anik C-3 -- in telescoped configuration -- will be carried into orbit in special cradles bolted to the deck
and bulkheads of the orbiter payload bay. Each truss-like aluminum structure contains an ejection system, a
turntable mechanism and lightweight sun shield.

Deployment procedures will be essentially identical for both spacecraft. SBS-3 will be deployed from the Columbia
about 3:30 p.m. EST, Nov. 11 and Anik C-3 about 24 hours later (3:25 p.m. EST, Nov. 12).

Predeployment activities begin about six hours before the spacecraft is ejected from the bay. Updated computations
on Columbia's orbit -- altitude, velocity, inclination -- are fed to the spacecraft control center which in turn provides
the mission control center in Houston with refined payload injection information. Then this is passed on to the
mission specialist aboard Columbia in charge of the deployment.

Shortly before ejection, Pilot Overmyer will orient the Columbia to the prescribed deployment attitude (close to
perpendicular to earth) with the cargo bay doors facing in the opposite direction of Columbia's direction of travel.
When the orbiter is properly pointed a series of events will take place under the watchful eyes of the mission
specialist -- Lenoir for SBS-3, Allen for Anik C-3.

The sun shield canopy will be drawn back to expose the satellite. A 50 rpm spin will be imparted to the cradle's
turntable giving the satellite and attached Payload Assist Module a rotating action to stabilize their path. At the
prescribed time explosive bolts will fire to release a Marman clamp holding the spring-loaded spacecraft down. It
will separate from the orbiter moving away from the Columbia at about three feet per second, while continuing to
orbit the earth at an altitude of 185 mi. (160 nm), a velocity of about 28,164 km/hr (17,500 mph) and an inclination
of 28.5 degrees.

Once deployment occurs the responsibility for the spacecraft shifts from NASA to the satellite's control center --
SBS control center in Washington, D.C., and Telesat Canada's control facility in Ottawa.

The orbiter will then move away to a position about 26 km (16 mi.) from the satellite. The Columbia will change to
an attitude so that the belly of the orbiter will face the satellite at the moment of the Payload Assist Module ignition.

Forty-five minutes after deployment from the payload bay, the perigee engine will automatically fire to place the
satellite into a highly elliptical transfer orbit.

SBS-3
Satellite Business Systems' SBS-3 is the first commercial satellite to be launched from the Space Transportation
System. It will share the payload bay with Telesat Canada's Anik C-3 on the first operational flight of the Space
Shuttle (STS-5).

SBS-3 is designed to provide all-digital communications and features time-division, multiple access techniques for
efficient use of satellite transmission communications.

The satellite is 2.1 m (7 ft.) in diameter and 6.4 m (21 ft.) tall when deployed in orbit. The exterior surface of the
satellite is covered with approximately 14,000 solar cells that generate 1,000 watts of dc power. An onboard power
subsystem, including rechargeable batteries, powers the satellite's communications subsystem, including 10
operational transponder channels. Redundant traveling-wave-tube amplifiers provide a transmit power of 20 watts
for each channel.

Three general types of services are provided by SBS:

Edited by Richard W. Orloff, 01/2001/Page 35


x Communications Network Service which consists of high capacity private networks for all-digital integrated
transmission of voice, data, video and electronic mail among an SBS customer's widely dispersed facilities in
the United States.

x Message Service I is a high quality, economical long distance service for businesses and a second version,
Message Service II, for residential customers to begin in 1982.

x Spare Transponder Service is an offering of spare satellite capacity for communications firms, broadcasters;
and cablecasters using the only Ku-band transponder capability offered by a U.S. carrier.

SBS-3 will weigh about 3,277 kg (7,225 lb.) when ejected from the payload bay.

This includes the Payload Assist Module (PAM-D) with 1,960 kg (4,325 lb.) of solid propellant for thrusting the
satellite from parking orbit to transfer orbit, an apogee kick motor with 495 kg (1,089 lb.) of solid propellant for
synchronous orbit injection and the satellite itself, weighing 600 kg (1,326 lb.) including about 136 kg (300 lb.) of
hydrazine fuel for eight to 10 years of stationkeeping operation.

The SBS-3 spacecraft is manufactured by Hughes Aircraft Co., El Segundo, Calif. SBS-1 and SBS-2 were launched
by NASA's Delta rocket .

SBS is a private communications company headquartered in McLean, Va. The firm is owned by subsidiaries of
Aetna Life and Casualty, Comsat General Corp. and IBM.

Edited by Richard W. Orloff, 01/2001/Page 36


Edited by Richard W. Orloff, 01/2001/Page 37
Edited by Richard W. Orloff, 01/2001/Page 38
ANIK C-3
Telesat Canada's Anik C-3 communications satellite will be launched from the bay of the orbiter Columbia on the
second day of the STS-5 mission. It will join four other operational Anik communications satellites in
geosynchronous orbit.

The C series satellites will be the most powerful domestic satellites in commercial service until the latter half of the
decade.

The satellite service of Telesat Canada is the principal means of providing modern voice, message, data, facsimile
and broadcast service to remote and northern parts of Canada. The satellite links complement and augment the
terrestrial communications networks and provide a large measure of system diversity to the terrestrial carriers.

The Anik C-3 satellite will be the first in a series to provide rooftop-to-rooftop transmission of integrated voice,
video and data communications for Canadian businesses, carry newly licensed Canadian pay-TV and other
broadcast services.

Anik C-3 will weigh about 632 kg (1,394 lb.) in geosynchronous orbit. Its solar cells produce more than 1,100 watts
of dc electrical power to operate the spacecraft's systems. The satellite is 2.1 m (7 ft.) wide and 6.4 m (21 ft.) tall
when fully deployed. The spin-stabilized Anik C-3 will operate in the high-frequency radio bands, 14 and 12 GHz
with 16 transponders.

The combination of higher transmission power (from 15-watt output tubes) and the 14/12 GHz bands will allow the
use of small 1.2 m (3.9 ft.) dish antennas in places, such as home rooftops and high density office buildings.

Anik C-3's antenna coverage will include virtually all of populated Canada with four contiguous spot beams serving
the western, west-central, east-central and eastern regions of the country. Telesat's customers will be able to choose
regional, half or whole nation coverage, depending on their needs.

The spacecraft was built under contract by Hughes Aircraft Co., El Segundo, Calif.

Telesat Canada is headquartered in Ottawa, Ontario, Canada.

Edited by Richard W. Orloff, 01/2001/Page 39


FLIGHT EXPERIMENTS
Shuttle Student Involvement Program

Three student experiments will be conducted aboard Columbia during STS-5. The experiments will be installed in
mid-deck stowage lockers in the orbiter cabin area. The experiments were selected from proposals made by students
through a program supervised by NASA and the National Science Teachers Association.

Growth of Porifera in Zero Gravity

The experiment of Aaron K. Gillette, now attending Western Carolina University, devised when he was a student at
Winterhaven High School, Winterhaven, Fla., is designed to study the effect of zero gravity on sponge, Porifera, in
relation to its regeneration of structure, shape and spicule (needle-like structure that supports soft tissue) formation
following separation of the sponge.

The experiment consists of 18 heat-sealed polyester packets containing Porifera Microciona (sponge) in a growth
solution. Starter ions (calcium and magnesium) and a fixative are separated by color-coded clamps from the growth
solution. To initiate the experiment, a color-coded clamp is released on each packet to liberate the starter into the
growth solution. At 30 minutes, one hour, 24 hours, 48 hours and mission termination, a color-coded clamp is
released on each of three packets to liberate the fixative. The experiment is configured for installation in half a mid-
deck stowage locker.

Sponsors for Gillette's experiment are Tania Hogan of Martin Marietta Aerospace and William Knott of NASA's
Kennedy Space Center.

Convection in Zero Gravity

D. Scott Thomas, now attending Utah State University, when a student at Richland High School, Johnstown, Pa., set
up an experiment to study surface tension convection in zero gravity. It will study the effects of boundary layer
conditions and geometries on the onset and character of the convection.

The Convection in Zero Gravity experiment consists of a frame holding four pans with hinged lids and heaters
imbedded in the bottom and sides.

A crew member removes the experiment from the mid-deck locker, secures it to the airlock wall and sets up a TV
camera. He then injects a pan with oil and activates the heater and TV camera. The heater will run for two and one-
half minutes, ample time for convection to occur. The camera will view the process for five minutes so that ceasing
of convection can be observed. Following the observation, the controller is turned off, oil is withdrawn, the pan
wiped out and the experiment continued with another pan while the first pan cools. After 10 cycles the experiment
is concluded and returned to the locker.

R. Gilbert Moore, Thiokol Corp., and Roger Kroes of NASA's Marshall Space Flight Center, are sponsors of the
experiment.

Formation of Crystals in Weightlessness

Michelle A. Issel, now attending American University, formerly of M.T. Sheehan High School, Wallingford, Conn.,
is conducting an experiment to compare crystal growth in zero gravity to that in one-g to determine if
weightlessness eliminates the causes of malformations in crystals.

Edited by Richard W. Orloff, 01/2001/Page 40


The experiment consists of a hot plate (solute cup) and a cold plate (sting) driven by small thermoelectric heat
pumps. The experiment is charged with a saturated solution tri-glycine sulphate before flight. The self-contained
experiment which is initiated by a switch is carried in a half-size mid-deck stowage locker.

John Alyward of United Technologies, Hamilton Standard and Liam Sarsfield Of NASA's Lewis Research Center,
Cleveland, are sponsors.

GETAWAY SPECIAL
Officially titled "Small Self-Contained Payloads," the Getaway Special program is offered by NASA to provide
anyone who wishes the opportunity to fly a small experiment aboard the Space Shuttle. The experiment must be of
scientific research and development nature.

The Getaway specials, which are flown on Shuttle missions on a space-available basis, are available to industry,
educational organizations, and domestic and foreign governments for legitimate scientific purposes.

The second Getaway Special payload will use X-rays to radiate through metallic samples and record their
appearance periodically on film during micro-gravity processing.

The study of physical processes occurring in liquid metals shortly before or during solidification is hampered by the
lack of direct optical observation.

Metallic samples which were processed and solidified on earlier space missions under micro-gravity conditions had
to be analyzed after the fact solely with the aid of polished cross-sections. The interpretation of results was often
difficult because of the missing intermediate stages in sample development.

In this experiment, X-rays will be used to radiate through the metallic samples and their appearance will be recorded
on film.

The objectives of this investigation include the development of an autonomously working X-Ray unit together with
a transparent thermostat (oven). The sample will consist of a liquid in dispersion of two insoluble metals which
exhibit a mixing gap in the liquid state. These metals will be homogenized by a temperature treatment.
Documentation of the homogenization and the time-dependent stability of the dispersion while cooling will be
investigated by the X-Ray technique.

With this technique, several phenomena may be made visible and quantitatively evaluated including diffusional
homogenization, particle movement, particle growth and convection currents.

The canister is located in the aft section of the payload bay.

The experiment is part of the material science program of the German Ministry of Research and Technology
(BMFT).

Edited by Richard W. Orloff, 01/2001/Page 41


ORBITER EXPERIMENTS PROGRAM
A complete and accurate assessment of Shuttle performance during the launch, boost, orbit, atmospheric entry and
landing phases of a mission requires precise data collection to document the Shuttle's response to these conditions.

The NASA Headquarters Office of Aeronautics and Space Technology (OAST), through its Orbiter Experiments
Program, is providing research experiments onboard the Shuttle orbiter to record specific, research-quality data.

The primary objective of the Orbiter Experiments Program is to increase the technology reservoir for development
of future space transportation systems. The data also will be useful to the Office of Space Flight (OSF) to further
certify Shuttle and expand its operational envelope.

In addition this data will be used to verify the accuracy of wind tunnel and other ground-based simulations made
prior to flight; verify ground-to-flight extrapolation methods; and verify theoretical computational methods.

STS-5 Orbiter Experiments include:

Aerodynamic Coefficient Identification Package (ACIP)

The primary objectives of the Aerodynamic Coefficient Identification Package are:

x To collect aerodynamic data during the launch, entry and landing phases of the Shuttle;

x To establish an extensive aerodynamic data base for verification of the Shuttle's aerodynamic performance and
the verification and correlation with ground-based data, including assessments of the uncertainties of such data;

x To provide flight dynamics data in support of other technology areas, such as aerothermal and structural
dynamics.

This package has flown on STS-1 through 4. It will fly again on STS-5 and current plans call for continued
operation on future Shuttle flights, including the operation of a second unit on OV-099. Shuttle orbiter Challenger.

Instruments in this package include dual-range linear accelerometers and rate gyros. Also included are the power
conditioner for the gyros, the power control system and the housekeeping components. The package is installed co-
linearly with the geometric axes of the orbiter and post-installation measurements made to establish the position
within 10 arc minutes.

The instruments continuously sense the dynamic X, Y and Z attitudes and performance characteristics of the orbiter
through these critical flight phases. The Aerodynamic Coefficient Identification Package also provides high rate
sampling of the positions of orbiter control surfaces for recording with the package's attitude data.

Principal technologist is D.B. Howes of Johnson Space Center, Houston.

Tile Gap Heating Effects (TGH) Experiment

Analyses and ground tests have shown that the gaps between the tiles of the thermal protection system generate
turbulent airflow, which will cause increased heating during the reentry phase of flight. Tests have also shown that
the heating effect may be reduced by optimum design of the gaps and by altering the radii at the edges of the tiles.
The tile gap experiment was devised to further the investigations of heating phenomena.

The results will enable improvements in reusable element thermal protection systems to reduce the convective
heating caused by gaps and other discontinuities.

Edited by Richard W. Orloff, 01/2001/Page 42


The orbiter will be instrumented with a removable panel 45.7 cm (18 in.) square, which will carry 11 tiles of
baseline material and size. The panel will be fitted to the underside of the orbiter fuselage. The gaps between tiles
will be carefully calculated and controlled during fitting to ensure that the heating rates generated during entry will
be no higher than those of the baseline tile array. The aim is to produce a design that will result in heating rates
lower than those of the baseline system.

In addition to gap spacing, the gap depth will also be controlled through the use of fillers fitted at the bottom of
certain gaps -- i.e., at the junction of the tiles and the orbiter fuselage skin. The radii at the outer edges of the tiles
will be controlled during fabrication to conform to calculations that show the reduced effects in combination with
the spacing. Thermocouples will be fitted to the tile surfaces and at various depths in the gaps to measure
temperatures during reentry.

The output of the thermocouples will be recorded on the orbiter's development flight instrumentation system. To
assist in evaluation, Tile Gap Heating Effects data will be compared to development flight instrumentation data
obtained from earlier missions.

This will be the fourth flight of the experiment which successfully flew on STS-2, 3 and 4. On STS-5 it will be
modified to investigate the effect of tile gap geometry on gap filler bar heating. The STS-5 test configuration is co-
sponsored by the Orbiter Experiments Project and the Orbiter Project.

Information provided by this test will aid the Orbiter Project in the evaluation of the filler bar heating phenomena.

Principal technologist is William C. Pitts, Ames Research Center, Mountain View, Calif.

Catalytic Surface Effects (CSE) Experiment

A strong shock wave will encompass the Shuttle orbiter during the atmospheric reentry maneuver. The shock wave
severely compresses and heats the air flowing through it, causing the molecules to dissociate and react chemically
with each other.

Computations show that as the dissociated atomic oxygen approaches the cooler regions of flow adjacent to the
orbiter, the atomic oxygen fails to recombine into molecular oxygen.

This experiment will investigate the chemical reaction caused by impingement of atomic oxygen on the Shuttle
thermal protection system which was designed on the assumption that the atomic oxygen would recombine at the
thermal protection system wall.

This chemical reaction releases additional heat which results in higher thermal protection system temperatures. In
this case, the surface is referred to as being a catalytic surface, that is. it allows the chemical reaction to take place.

If the thermal protection system surface is non-catalytic, the atomic oxygen will not recombine into molecular
oxygen and the heating rates will be lowered. Thus, the temperature of the orbiter during reentry will be lower. With
lower temperatures, orbiter thermal protection system weight could be reduced, its flight envelope could be
expanded, or greater reusability could result.

The technology objective is to verify analytical predictions which could not be adequately simulated in ground-
based facilities. The results will provide data and improved computational techniques for future thermal protection
system designs.

The Catalytic Surface Effects will use baseline tiles, selected from those having development flight instrumentation
thermocouples, located on or near the orbiter lower fuselage centerline. The seven tiles will be sprayed with an
overcoating mixture of chrome-iron-spinel, a highly efficient catalytic material and a vinyl acetate binder which will

Edited by Richard W. Orloff, 01/2001/Page 43


protect the overcoat during ground operations. The mixture is compatible with the existing tile and coating and will
not alter the thermal or mechanical properties of the uncoated portions of the thermal protection system. During
orbiter ascent, the vinyl acetate will burn off the tile surface, leaving the chrome-iron-spinel exposed

Thermocouple measurements recorded during reentry will be used to determine Catalytic Surface Effects
performance. Comparison of this experiment's data with data taken on previous flights from uncoated tiles will aid
in the performance evaluation.
This will be the fourth flight of the experiment. Data collected on the STS-2, 3 and 4 has been useful in verifying
the preflight predictions that the tile surfaces are non-catalytic.

At the end of each mission, the overcoat will be removed from the seven tiles, leaving the thermal protection system
in its original condition.

Principal technologist is David A. Stewart, Ames Research Center.

Dynamic, Acoustic and Thermal Environment (DATE) Experiment

To fully and economically exploit the benefits of the orbiter's large cargo-carrying capability, it is necessary to
predict payload environments with accuracy and dispatch.

Such predictions will facilitate payload development and reduce the need for ultraconservative design and testing.

The Dynamic, Acoustic and Thermal Environment experiment will collect information for use in making credible
predictions of cargo-bay environments. These environments are neither constant nor consistent throughout the bay
and are influenced by interactions between cargo elements.

The instrumentation includes accelerometers, microphones, thermocouples and strain gages on payloads and in the
cargo bay. Sensor outputs will be recorded for post-flight interpretation. DATE instrumentation has successfully
flown on STS-1 through 4.

The Goddard Space Flight Center, Greenbelt, Md., will be responsible for the data reduction.

Principal technologist is William Bangs of Goddard.

ATMOSPHERIC LUMINOSITIES INVESTIGATION


(GLOW EXPERIMENT)
Nighttime photographs taken by the crew on STS-3 revealed an observable luminosity (glow) of unknown origin
enveloping certain structural elements of the orbiter, particularly on the tail section and engine pods.

The luminosity was not symmetrical and appeared to be more prevalent on the port side of the vehicle. The best
guess on the cause of this effect is recombination of ionospheric oxygen ions.

The purpose of the STS-5 investigation is to determine the spectral content of the Space Transportation System
induced atmospheric luminosities which have relevance to scientific; (e.g., ion chemistry of the atmosphere) and
engineering (e.g., potential contaminant to optical experiments) aspects of payload operations.

Two cameras, a Nikon 35 mm and a Hasselblad, are used, one in each aft flight deck window. During two nighttime
sequences, the crew activates the cameras four minutes after optical sunset (to assure no trace of sunlight) and after
moonset and stops the film after 32 exposures or prior to sunrise. After flight, the photographs will be analyzed for
possible causes of the luminosity effect.

E.L. Michel of Johnson is responsible for the investigation.

Edited by Richard W. Orloff, 01/2001/Page 44


OXYGEN ATOM INTERACTION WITH MATERIALS TEST
Surfaces of materials used in the orbiter payload bay and exposed during STS-1 through STS-4 were examined after
flight.

Paints and polymers, in particular Kapton used on the television camera thermal blanket, showed significant change.
Generally, the change was a loss of surface gloss on the polymer with apparent aging on the paint surfaces.

The Kapton surfaces showed the greatest change, and postflight analyses showed mass loss of 4.8 percent on STS-2
and 35 percent on STS-3 for most heavily affected surfaces.

This materials test is being conducted on STS-5 to obtain quantitative reaction rates of low earth orbit oxygen atoms
with various materials used on payloads. Data obtained on STS-2 through 4 indicate that some payloads may be
severely limited in life due to oxygen effect. The STS-5 test would provide data for assessment of oxygen effects
and possible fixes.

Test material is tensioned with hold down springs to six panels which will be mounted atop the Development Flight
Instrumentation using existing power and switch capabilities. Materials will be returned for evaluation of space
exposure effects.

The test material is located in the payload bay atop the Development Flight Instrumentation.

The responsible organization is the Johnson Space Center.

Edited by Richard W. Orloff, 01/2001/Page 45


DEVELOPMENT FLIGHT INSTRUMENTATION
The Development Flight Instrumentation is a data collection and recording package, located in the aft areas of the
payload bay, consisting of three magnetic tape recorders, wideband frequency division multiplexers, a pulse code
modulation master unit and signal conditioners. The recorder can record 28 tracks of wideband analog data on
systems conditions and performance simultaneously.

The hatch on the side of the orbiter is scheduled to be opened within 30 minutes after landing. The crew will leave
the orbiter at the direction of flight controllers at the Mission Control Center.

Columbia will be towed off the runway at Edwards to the Mate/Demate Device at the nearby Dryden Flight
Research Facility.

Once in the Mate/Demate Device, Columbia's fuel cell supply tanks will be drained of residual cryogenic liquids,
the Shuttle main engines will be purged and unfired pyrotechnic devices will he disconnected .

Ferry plugs will be installed in engine nozzles and locks put in place on the engines and flight control surfaces to
keep them from moving during the ferry flight to Kennedy Space Center.

The aerodynamic tail cone will be installed over the aft end of the spacecraft and the orbiter will be positioned and
bolted on top of the 747 Shuttle Carrier Aircraft.

The 747 is scheduled to leave California on the first leg of its two-day ferry flight to KSC five days after landing.
An overnight stop is scheduled to refuel the 747 carrier aircraft and to rest the flight crew.

Edited by Richard W. Orloff, 01/2001/Page 46


STS-5 LANDING OPPORTUNITIES
FOR NASA DRYDEN
(Based on a 7:19 a.m. EST launch)
NOTE: Landing opportunities are in Pacific Standard Time.

Approximate Elapsed Time Cross Range


Orbit Landing PST Days/Minutes (n mi)

1 6:05 a.m. (night) 0/1:48 460


2 7:10 0/3:21 398
3 9:16 0/4:57 578

16 4:39 a.m. (night) 1/10:20 593


17 6:14 1/11:55 402
18 7:49 1/13:30 451
19 9:24 1/15:05 734

31 3:12 a.m. (night) 1/22:53 797


32 4:48 (night) 2/00:29 481
33 6:23 2/02:04 394
34 7:59 2/03:40 549

47 3:21 a.m. (night) 2/23:02 631


48 4:56 (night) 3/00:37 413
49 6:31 3/02:12 432
50 8:06 3/03:47 686

63 3:20 a.m. (night) 3/23:01 529


64 4:55 (night) 4/00:36 390
65 6:30 4/02:11 491
66 8:04 4/03:45 815

78 1:43 a.m. (night) 4/21:24 749


79 3:17 (night) 4/22:58 458
80 4:25 (night) 5/00:33 397
81 EOM 6:27 5/02:08 573

94 1:40 a.m. (night) 5/21:21 631


95 3:15 (night) 5/22:56 412
96 4:49 (night) 6/00:30 429
97 6:23 6/02:04 677

Edited by Richard W. Orloff, 01/2001/Page 47


Edited by Richard W. Orloff, 01/2001/Page 48
Edited by Richard W. Orloff, 01/2001/Page 49
Edited by Richard W. Orloff, 01/2001/Page 50
Edited by Richard W. Orloff, 01/2001/Page 51
LANDING AND POSTLANDING OPERATIONS
Kennedy Space Center is responsible for ground operations of the orbiter vehicle once it has rolled to a stop on the
runway at Edwards, including preparations for returning the reusable vehicle to Kennedy Space Center for its next
mission.

As soon as Columbia rolls to a stop, the recovery convoy will head toward the vehicle to begin preliminary securing
and safing operations.

At the same time, the flight crew will turn off the auxiliary power units and turn on cooling systems and safe the
orbiter's maneuvering and reaction control systems.

After SCAPE- (Self Contained Atmospheric Protection Ensemble) suited personnel have determined that hazardous
vapor levels are below significant levels, the 100-member ground crew will perform such activities as connecting
ground and purge air units, conducting a post-landing inspection and attaching the ground tow vehicle.

The mobile wind machine is used only if highly concentrated levels of explosive vapors are detected by the ground
team.

Once the initial safety assessment is made, other teams of SCAPE-suited personnel and vehicles with maneuverable
access platforms will then be positioned at the rear of the orbiter, near the vehicle's T-0 umbilical connection panels.
The two large transporters, the Purge and Coolant Umbilical Access Vehicles, will then be moved into place behind
the orbiter and their lines will be connected to the orbiter umbilical panels.

If everything is normal , and no explosive gases are detected, the Purge and Coolant Umbilical Access Vehicles will
be moved into position. Freon lines and purge duct connections will be completed and the flow of coolant and
purge air through the umbilical lines will provide cooling to the orbiter's systems. This cooling helps protect the
orbiter's electronic equipment. Purge air will provide cool and humidified air conditioning to the orbiter's payload
bay and other cavities to remove any residual explosive or toxic fumes and provide a safe, clean and cool
environment inside the Columbia.

When further monitoring of vapor readings around the forward half of the orbiter indicates there are no
concentrations of toxic gases, SCAPE-suited technicians working the forward section will be replaced by non-
SCAPE personnel. The mobile white room will be moved into place around the orbiter crew access hatch. The
hatch is opened and the flight crew is allowed to leave the crew cabin. The flight crew will be replaced by other
astronauts who will complete the task of safing the vehicle.

The hatch on the side of the orbiter is scheduled to be opened within 30 minutes after landing. The crew will leave
the orbiter at the direction of flight controllers at the Mission Control Center.

Columbia will be towed off the runway at Edwards to the Mate/Demate Device at the nearby Dryden Flight
Research Facility.

Once in the Mate/Demate Device, Columbia’s fuel cell supply tanks will be drained of residual cryogenic liquids,
the Shuttle main engines will be purged and unfired pyrotechnic devices will be disconnected.

Ferry plugs will be installed in engine nozzles and locks put in place on the engines and flight control surfaces to
keep ,them from moving during the ferry flight to Kennedy Space Center.

The aerodynamic tail cone will be installed over the aft end of the spacecraft and the orbiter will be positioned and
bolted on top of the 747 Shuttle Carrier Aircraft.

The 747 is scheduled to leave California on the first leg of its two-day ferry flight to KSC five days after landing.
An overnight stop is scheduled to refuel the 747 carrier aircraft and to rest the flight crew.

Edited by Richard W. Orloff, 01/2001/Page 52


SPACEFLIGHT TRACKING AND DATA NETWORK (STDN)
One of the key elements in the Shuttle mission is the capability to track the spacecraft, communicate with the
astronauts and to obtain the telemetry data that informs ground controllers of the condition of the spacecraft and its
astronauts.

The hub of this network is at NASA's Goddard Space Flight Center, Greenbelt, Md., where the Spaceflight
Tracking and Data Network (STDN) and the NASA Communications Network (NASCOM) is located.

With the exception of very brief periods during the launch, flight, and recovery of STS-5, Goddard receives all
telemetry, radar and air-to-ground communications and relays the information to Johnson in Houston, and other
NASA and Department of Defense facilities participating in the mission.

The Spaceflight Tracking and Data Network is a complex NASA worldwide system that provides real time
communications with the Space Shuttle orbiter and crew. The network is operated by Goddard. Approximately
2,500 personnel are required to operate the network.

The network consists of 15 ground stations equipped with 4.3, 9, 12 and 26 m (14, 3O, 40 and 85 ft.) S-band
antenna systems and C-band radar systems, augmented by 15 Department of Defense geographical locations
providing C-band support and one Department of Defense 18.3 m (60 ft.) S-band antenna system.

In addition, there are six major computing interfaces located at the Network Operations Control Center (NOCC) and
at the Operations Support Computing Facility (OSCF), both at Goddard; Western Space and Missile Center, Calif.;
Air Force Satellite Control Facility, Colo.; White Sands Missile Range, N.M.,; and Eastern Space and Missile
Center, Fla., providing real time network computational support.

The network has agreements with the governments of Australia, Spain, Senegal, Botswana, Chile, United Kingdom
and Bermuda to provide NASA tracking stations support to the Space Transportation System program.

Should the Johnson Mission Control Center be seriously impaired for an extended time, the Goddard Network
Operations Control Center becomes an emergency mission control center manned by Johnson personnel, with the
responsibility of safely returning the Space Shuttle orbiter to a landing site.

The Merritt Island, Fla., S-band station provides the appropriate data to the Launch Control Center at Kennedy and
the Mission Control at Johnson during prelaunch testing and the terminal countdown. During the first minutes of
launch and during the ascent phase, the Merritt Island and Ponce de Leon, Fla., S-band and Bermuda S-band
stations, as well as the C-band stations located at Bermuda; Wallops Island, Va.; Grand Bahama; Grand Turk;
Antigua; Cape Canaveral; and Patrick Air Force Base, Fla., provide appropriate tracking data, both high speed and
low speed, to the Kennedy and Johnson Control Centers.

During the orbital phase, all the S-band and some of the C-band stations that see the Space Shuttle orbiter at 3
degrees above the horizon support and provide appropriate tracking, telemetry, air-ground and command support to
the Johnson Mission Control Center through Goddard.

During the nominal reentry and landing phase planned for Edwards Air Force Base, Calif., the Goldstone and
Buckhorn, Calif.; S-band stations and C-band stations at the Pacific Missile Test Center, Vandenberg Air Force
Base, Edwards Air Force Base and Dryden Flight Research Facility will provide highly critical tracking, telemetry,
command and air-ground support to the orbiter and send appropriate data to the Johnson and Kennedy Control
Center.

Edited by Richard W. Orloff, 01/2001/Page 53


NASA TRACKING STATIONS

Location Equipment

Ascension Island (ACN) S-band, UHF A/G


Bermuda (BDA) S-band, C-band, UHF A/G
Buckhorn (BUC) S-band, C-band
Goldstone (GDS) S-band, UHF A/G
Guam (GWM) S-band, UHF A/G
Hawaii (HAW) S-band, UHF A/G
Merritt Island (MIL) S-band, UHF, A/G
Santiago (AGO) S-band
Madrid (MAD) S-band. UHF A/G
Orroral (ORR) S-band
Botswana (BOT) UHF A/G
Dakar (DKR) UHF A/G
Yarragadee (YAR) UHF A/G

Personnel:

Tracking Stations, 1,110*


Goddard Space Flight Center, 1,400

* More than 500 of whom are local residents.

Edited by Richard W. Orloff, 01/2001/Page 54


HUNTSVILLE OPERATIONS SUPPORT CENTER
The Huntsville Operations Support Center is a facility at the Marshall Space Flight Center in Huntsville, Ala., which
supports launch activities and powered flight at the Kennedy Space Center, Fla., and the Johnson Space Center,
Houston.

During premission testing, countdown, launch and powered flight toward orbit, Marshall and contractor engineers
and scientists man consoles in the support center to monitor real-time data being transmitted from the Shuttle. Their
purpose is to evaluate and help solve problems that might occur with Marshall-developed Space Shuttle propulsion
system elements, including the Shuttle Main engines, external tank, and solid rocket boosters. They will also work
problems with the overall main propulsion system and the range safety system.

The data providing information on the "health" of these systems are gathered by sensors aboard the Shuttle and are
instantaneously transmitted from the launch site to the Huntsville Operations Support Center. There the information
is processed by computers and displayed on screens and other instruments at 12 stations in the Engineering Console
Room on the second floor. More than 3,000 temperature, pressure, electrical voltage and other measurements are
made every second. During the 10 hours of peak activity before and during launch, more than 11 million
measurements are assessed by teams of experts in the support center.

Support center personnel view the Shuttle via two closed circuit television lines. They also have access to more than
25 direct communications lines that link them with the launch site at Kennedy, Mission Control at Johnson and with
Shuttle propulsion system contractor plants.

If a problem is detected by the experts at one of the stations in the support center console room, engineers on the
consoles immediately alert appropriate individuals at the Kennedy and Johnson Centers, and operations center
managers in the Shuttle action center, a conference room adjacent to the console room. They also pass the
information to the appropriate teams of specialists in the operations center working area nearby. There are separate
teams to work difficulties for each of the elements.

Edited by Richard W. Orloff, 01/2001/Page 55


STS-5 CREWMEMBERS

S82-36286 – The official portrait of STS-5 mission crewmembers includes astronauts Vance D. Brand (second left),
commander; Robert F. Overmyer (second right), pilot; and Joseph P. Allen (left) and William S. Lenoir, both
mission specialists. They pose in blue flight suits holding their helmets, with a space shuttle model and the official
insignia for STS-5 in the background.

No copyright is asserted for this photograph. If a recognizable person appears in the photo, use for commercial
purposes may infringe a right of privacy or publicity. It may not be used to state or imply the endorsement by NASA
or by any NASA employee of a commercial product, process or service, or used in any other manner that might
mislead. Accordingly, it is requested that if this photograph is used in advertising and other commercial promotion,
layout and copy be submitted to NASA prior to release.

PHOTO CREDIT: NASA or National Aeronautics and Space Administration.

Edited by Richard W. Orloff, 01/2001/Page 56


BIOGRAPHICAL DATA
NAME: Vance DeVoe Brand, STS-5 Commander, NASA Astronaut

BIRTHPLACE AND DATE: Born in Longmont, Colo., May 9, 1931. His parents, Dr. and Mrs. Rudolph W. Brand,
reside in Longmont.

PHYSICAL DESCRIPTION: Blond hair; gray eyes; height: 5 feet 11 inches; weight: 175 pounds.

EDUCATION: Graduated from Longmont High School, Colo.; received a bachelor of science degree in business
from the University of Colorado in 1953, a bachelor of science degree in aeronautical engineering from the
University of Colorado in 1960, and a master's degree in business administration from the University of California
at Los Angeles in 1964.

MARITAL STATUS: Married to the former Beverly Ann Whitnel. Her parents, Mr. and Mrs. Otis W. Whitnel,
reside in Houston.

CHILDREN: Susan N., April 30, 1954; Stephanie, Aug. 6, 1955; Patrick R., March 22, 1958; Kevin S., Dec. 1,
1963, and Erik R., May 11, 1981.

NASA EXPERIENCE: One of the 19 pilot astronauts selected by NASA in April 1966, Brand first served as a crew
member of the thermal vacuum chamber testing of the prototype command module and was a support crewman for
the Apollo 8 and 13 missions. Later he was backup command module pilot for Apollo 15 and backup commander
for the Skylab 3 and 4 missions.

Vance Brand made his first space flight on July 15, 1975, as Apollo command module pilot on the Apollo-Soyuz
Test Project (ASTP) mission. This joint space flight resulted in the first historic meeting in space between American
astronauts and Soviet cosmonauts. Other crewmen taking part in this nine-day earth-orbital mission were Thomas P.
Stafford, Apollo commander; Donald K. Slayton, Apollo docking module pilot; Cosmonaut Alexei Leonov, Soyuz
commander; and Cosmonaut Valeri Kubasov, Soyuz flight engineer.

The Soyuz spacecraft was launched at the Baikonur Cosmodrome in Central Asia, and the Apollo was launched
71/2 hours later at Cape Canaveral. Two days later the Apollo spacecraft accomplished a successful rendezvous and
docking with Soyuz. The linkup tested a unique, new docking system and paved the way for future international
cooperation in space. Twenty-eight experiments were performed during the flight.

There were 44 hours of docked joint activities which included four crew transfers between the Apollo and the
Soyuz. All major ASTP objectives were accomplished, and experience was gained in the conduct of complex,
international manned missions. Six records for docked and group flight were set on the mission and are recognized
by the Federation Aeronautique Internationale. Apollo splashed down in the Pacific Ocean near Hawaii, less than a
mile from the targeted splash point, and was promptly recovered by the USS NEW ORLEANS. Brand logged 217
hours on his first space flight.

Edited by Richard W. Orloff, 01/2001/Page 57


BIOGRAPHICAL DATA
NAME: Robert F. Overmyer, Colonel, USMC, STS-5 Pilot, NASA Astronaut

BIRTHPLACE AND DATE: Born July 14, 1936, in Lorain, Ohio, but considers Westlake, Ohio his hometown.

PHYSICAL DESCRIPTION: Brown hair; blue eyes; height: 5 feet, 11-3/4 inches; weight: 180 pounds.

EDUCATION: Graduated from Westlake High School, Ohio, in 1954; received a bachelor of science degree in
physics from Baldwin-Wallace College in 1958; master of science degree in aeronautics with a major in
aeronautical engineering from the U. S. Naval Postgraduate School in 1964.

MARITAL STATUS: Married to the former Katherine E. Jones of Pittsburgh. Her parents, Mr. and Mrs. Henry R.
Jones, now reside in Highland Beach, Fla.

CHILDREN: Carolyn Marie, 1966; Patricia Ann, 1968; Robert Rolandus, 1970.

NASA EXPERIENCE: He was selected as a NASA astronaut in 1969 after the U.S. Air Force Manned Orbiting
Laboratory Program was canceled. His first assignment with NASA was engineering development duties on the
Skylab Program from 1969 until November 1971. From November 1971 until December 1972, he was a support
crew member for Apollo 17 and was the launch capsule communicator. From January 1973 until July 1975, he was
a support crew member for the Apollo-Soyuz Test Project and was NASA capsule communicator in the mission
control center in Moscow. In 1976, he was assigned duties on the Space Shuttle Approach and Landing Test (ALT)
Program and was the prime T-38 chase pilot for orbiter Free-Flights 1 and 3.

Edited by Richard W. Orloff, 01/2001/Page 58


BIOGRAPHICAL DATA
NAME: Joseph P. Allen, PhD, STS-5 Mission Specialist, NASA Astronaut

BIRTHPLACE AND DATE: Born in Crawfordsville, Ind., on June 27, 1937. His parents, Mr. and Mrs. Joseph P.
Allen III, reside in Greencastle. Ind.

PHYSICAL DESCRIPTION: Brown hair; blue eyes; height: 5 feet 6 inches; weight: 125 pounds.

EDUCATION: Attended Mills School and is a graduate of Crawfordsville High School in Indiana; received a
bachelor of arts degree in math-physics from DePauw University in 1959; a master of science degree and a
doctorate in physics from Yale University in 1961 and 1965, respectively.

MARITAL STATUS: Married to the former Bonnie Jo Darling of Elkhart, Ind. Her parents, Mr. and Mrs. W. C.
Darling, reside in Elkhart.

CHILDREN: David Christopher, September 1968; Elizabeth Darling, May 1972.

NASA EXPERIENCE: Allen was selected as a scientist-astronaut by NASA in August 1967. He completed flight
training at Vance Air Force Base, Okla. He served as mission scientist while a member of the astronaut support
crew for Apollo 15 and served also as a staff consultant on science and technology to the President's Council on
International Economic Policy.

From August 1975 to 1978, Allen served as NASA Assistant Administrator for Legislative Affairs in Washington,
D.C. Returning to the Johnson Space Center in 1978 as a senior scientist astronaut, Allen was assigned to the
operations mission development group. He served as a support crew member for the first orbital flight test of the
Space Shuttle transportation system, and was the entry CAPCOM for this mission. In addition, in 1980 and 1981, he
worked as the technical assistant to the Director of Flight Operations.

Edited by Richard W. Orloff, 01/2001/Page 59


BIOGRAPHICAL DATA
NAME: William B. Lenoir, PhD, STS-5 Mission Specialist, NASA Astronaut

BIRTHPLACE AND DATE: Born on March 14, 1939, in Miami, Fla. His father, Samuel S. Lenoir, resides in
Miami.

PHYSICAL DESCRIPTION: Brown hair; brown eyes; height: 5 feet 10 inches; weight: 150 pounds.

EDUCATION: Attended primary and secondary schools in Coral Gables, Fla.; a graduate of the Massachusetts
Institute of Technology where he received a bachelor of science degree in electrical engineering in 1961, a master of
science in 1962, and a doctorate in 1965.

MARITAL STATUS: Married to the former Elizabeth May Frost. Her mother, Mrs. Thomas F. Frost, resides in
Brookline, Mass.

CHILDREN: William B. Jr., April 6, 1965; Samantha E., March 20, 1968.

NASA EXPERIENCE: Lenoir was selected as a scientist-astronaut by NASA in August 1967. He completed the
initial academic training and a 53-week course in flight training at Laughlin Air Force Base, Texas.

Lenoir was backup science-pilot for Skylab 3 and Skylab 4, the second and third manned missions in the Skylab
Program. During Skylab 4, he was co-leader of the visual observations project and coordinator between the flight
crew and the principal investigators for Apollo telescope mount solar science matters.

From September 1974 to July 1976, Lenoir spent approximately half of his time as leader of the NASA Satellite
Power Team. This team was formed to investigate the potential of large-scale satellite power systems for terrestrial
utility consumption and to make program recommendations to NASA Headquarters.

Lenoir has supported the Space Shuttle program in the areas of payload deployment and retrieval. His interest in the
remote sensing of the earth and its resources continues, with particular emphasis on the role of man.

Edited by Richard W. Orloff, 01/2001/Page 60


SPACE SHUTTLE PROGRAM MANAGEMENT
NASA Headquarters

James M. Beggs Administrator


Dr. Hans Mark Deputy Administrator
Maj. General J. A. Abrahamson Associate Administrator for Space Flight
L. Michael Weeks Deputy Associate Administrator for Space Flight
Joe H. Engle Assistant Associate Administrator for Space Flight (Space Transportation)
Isaac T. Gilliam, IV Assistant Associate Administrator for Space Flight (Policy)
Richard J. Wisniewski Assistant Associate Administrator for Space Flight (Institutions)
Robert E. Smylie Associate Administrator for Space Tracking and Data Systems

Ames Research Center

C. A. Sylvertson Director

Dryden Flight Research Center

John A. Manke Facility Manager


Gary Layton Shuttle Project Manager

Goddard Space Flight Center

Dr. Noel Hinners Director


John J. Quann Deputy Director
Richard S. Sade Director of Networks Space Tracking and Data Network (STDN)

Johnson Space Center

Gerald D. Griffin Director


Henry E. Clements Associate Director
Clifford E. Charlesworth Deputy Director
Glynn S. Lunney Manager, Space Shuttle Program
Arnold D. Aldrich Manager, Space Shuttle Orbiter Project Office
George W. S. Abbey Director of Flight Operations
Aaron Cohen Director of Engineering and Development
Lynwood C. Dunseith Director of Data Systems and Analysis

Kennedy Space Center

Richard G. Smith Director


George F. Page Deputy Director
Robert H. Gray Manager, Shuttle Projects Office
John J. Neilon Manager, Cargo Projects Office
Thomas E. Utsman Director, Shuttle Operations;/Technical Support
Thomas S. Walton Director, Cargo Operations
Alfred D. O’Hara Director, STS Processing

Edited by Richard W. Orloff, 01/2001/Page 61


Marshall Space Flight Center

Dr. William R. Lucas Director


Thomas J. Lee Deputy Director
Robert E. Lindstrom Manager, MSFC Shuttle Projects Office
James E. Kingsbury Director, Science and Engineering Directorate
James B. Odom Deputy Manager for Production and Logistics, MSFC
Shuttle Projects Office and Acting Manager, External Tank
Project
George B. Hardy Deputy Manager for Development, MSFC Shuttle Projects
Office
Lawrence B. Mulloy Manager, Solid Rocket Booster Project, MSFC Shuttle
Projects Office
Lowell K. Zoller Manager, Engineering and Major Test Management Office,
MSFC Shuttle Projects Office
Judson A. Lovingood Manager, Space Shuttle Main Engine Project, MSFC
Shuttle Projects Office

Edited by Richard W. Orloff, 01/2001/Page 62


SHUTTLE FLIGHTS AS OF OCTOBER 1982
4 TOTAL FLIGHTS OF THE SHUTTLE SYSTEM

STS-4
06/27/82 – 07/04/82
STS-3
03/22/82 – 03/30/82
STS-2
11/12/81 – 11/14/81
STS-1
04/12/81 - 04/14/81

OV-102
Columbia
(4 flights)

Edited by Richard W. Orloff, 01/2001/Page 63

You might also like