Professional Documents
Culture Documents
0)
1 Top of Form
Which interface configuration command will affect the EIGRP metric calculation?
Router(config-if)# metric 896
2 Top of Form
Which two statements describe the purpose of the EIGRP network command? (Choose two.)
Determines which networks are advertised within an EIGRP update across the network.
3 Top of Form
Which statement is true concerning EIGRP?
It sends partial updates only to the routers that need the information.
It sends full updates only to the routers that need the information.
4 Top of Form
A network administrator notices the above line within the show ip route output of RTA. Given this
information, which statement is true?
RTA is configured to manually summarize the 2.1.0.0 network.
RTA automatically inserted this summary when the command network 2.1.0.0 was entered in
router mode.
RTA learned network 2.1.0.0 from another redistributed protocol.
5 Top of Form
Refer to the exhibit. The routers in the exhibit are using EIGRP. Router RTA is the hub router and
router RTB is a spoke router. What should be done to stop RTB from sending connected, summary
static routes?
Configure the eigrp stub command on RTA and RTB.
It transitions from passive to active state for that network and queries its neighbors.
It transitions from active to passive state for that network and queries its neighbors.
Bottom of Form
7 Top of Form
Refer to the exhibit. Which configuration statement for the serial interface on Router C is true
assuming a multipoint configuration?
The bandwidth should be left the default value.
8 Top of Form
Which statement best describes a route marked as active in the EIGRP topology table?
The route is stable and available for use.
9 Top of Form
What are two effective ways to prevent the EIGRP stuck in active problem? (Choose two.)
modify keepalive timers on point-to-point connections
10 Top of Form
Given the configuration statements shown in the diagram and assuming that EIGRP has already be
enabled for this network, which statement is true?
RTC will enter a route to 2.1.0.0/16, sourced from the null0 interface, into its route table.
RTC will accept the 2.1.0.0/16 route and assign it an administrative distance of 90.
RTD will accept the 2.1.0.0/16 route and assign it an administrative distance of 5.
RTD will receive two routes, the summary route of 2.1.0.0/16 and the automatic classful route o
2.0.0.0/8.
Bottom of Form
11 Top of Form
Refer to the exhibit. Based on the displayed EIGRP authentication configuration, what can be
concluded?
Authentication will fail because the key chain names do not match.
Authentication will fail because the key numbers do not match.
12 Top of Form
The network administrator wants RTA to send only the summarized route of 10.10.0.0/16 to RTB.
Which configuration will accomplish this?
RTA(config)# interface s0/0
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
RTA(config-if)# exit
RTA(config)# router eigrp 101
RTA(config-router)# no auto-summary
RTA(config)# interface s0/1
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
RTA(config-if)# exit
RTA(config)# router eigrp 101
RTA(config-router)# no auto-summary
RTA(config)# interface s0/0
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
RTA(config)# interface s0/1
RTA(config-if)# ip summary-address eigrp 101 10.10.0.0 255.255.0.0
Bottom of Form
13 Top of Form
Assuming that EIGRP is enabled on both routers, what must be configured to ensure that Router A
be able to reach the 2.2.2.0/24 network?
Use the command no auto-summary to disable automatic summarization.
Use the command ip address-summary to ensure that Router A recognizes the 2.2.2.0 netwo
EIGRP supports VLSM and will automatically recognize the 2.2.2.0 network.
EIGRP does not support VLSM, therefore cannot be used with discontiguous networks.
Bottom of Form
14 Top of Form
When would a router have a feasible successor in the topology table?
when a neighboring router that is currently being used for packet forwarding fails
when the feasible distance reported by the next hop router is less than the advertised distance
the destination
when the advertised distance reported by the next hop router is less than the feasible distance
the destination
when there is no successor listed or identified in the topology table
Bottom of Form
15 Top of Form
When must auto-summarization be disabled?
when utilizing VLSM
17 Top of Form
Refer to the exhibit. RTA cannot form a neighbor relationship with RTB. What should be done to
resolve this problem?
The subnet mask for network 10.1.1.0 on RTB must be configured as a wild mask.
The bandwidth for the serial0 interface on RTB must be set to 64 kbps.
The EIGRP hello interval for the serial0 interface on RTB must be set to 10 seconds.