Professional Documents
Culture Documents
i
Manual Rev: 1.1
Release Date: July 2004
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
Micro-Star International
MS-7025
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation
ii
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
Revision History
Revision Revision History Date
V1.0 First release for PCB 1.X July 2004
with nVidia nForce3 Ultra
V1.1 First release for PCB 1.X July 2004
with nVidia nForce3 Ultra
For European manuals
iii
Technical Support
If a problem arises with your system and no solution can be obtained from the user’s
manual, please contact your place of purchase or local distributor. Alternatively,
please try the following help resources for further guidance.
† Visit the MSI homepage & FAQ site for technical guide, BIOS updates, driver
updates, and other information: http://www.msi.com.tw & http://www.msi.
com.tw/program/service/faq/faq/esc_faq_list.php
† Contact our technical staff at: support@msi.com.tw
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Keep this equipment away from humidity.
4. Lay this equipment on a reliable flat surface before setting it up.
5. The openings on the enclosure are for air convection hence protects the equip-
ment from overheating. Do not cover the openings.
6. Make sure the voltage of the power source and adjust properly 110/220V be-
fore connecting the equipment to the power inlet.
7. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
8. Always Unplug the Power Cord before inserting any add-on card or module.
9. All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a service
personnel:
† The power cord or plug is damaged.
† Liquid has penetrated into the equipment.
† The equipment has been exposed to moisture.
† The equipment has not work well or you can not get it work according to
User’s Manual.
† The equipment has dropped and damaged.
† The equipment has obvious sign of breakage.
12. Do not leave this equipment in an environment unconditioned, storage
temperature above 60 0 C (140 0F), it may damage the equipment.
iv
CONTENTS
FCC-B Radio Frequency Interference Statement ......................................................... ii
Copyright Notice .............................................................................................................. iii
Revision History .............................................................................................................. iii
Safety Instructions ......................................................................................................... iv
Technical Support .......................................................................................................... iv
English ..................................................................................................................... E-1-1
1. Getting Started ............................................................................................... E-1-3
2. Hardware Setup ............................................................................................ E-2-1
3. BIOS Setup ..................................................................................................... E-3-1
Français ...................................................................................................................... F-1
Manuel d’utilisation ................................................................................................ F-3
Deutsch .................................................................................................................. G-1
Benutzerhandbuch ............................................................................................... G-3
v
Getting Started
K8N Neo 2
(MS-7025 v1.X)
ATX mainboard
English
E-1-1
MS-7025 ATX Mainboard
E-1-2
Getting Started
Chap t er 1 . Ge tting
Started
Getting Started
Thank you for choosing the K8N Neo2 Platinum (MS-7025)
v1.X ATX mainboard. The K8N Neo2 Platinum mainboard is based
on nVIDIA® nForce™ 3 Ultra chipset for optimal system efficiency.
Designed to fit the advanced AMD® K8 Athlon 64 FX / Athlon 64
processor, the K8N Neo2 Platinum mainboard delivers a high per-
formance and professional desktop platform solution.
E-1-3
MS-7025 ATX Mainboard
Mainboard Specifications
CPU
† Supports Socket-939 for AMD K8 Athlon 64 FX / Athlon 64 (Socket939) processor
† Supports up to 3500+, 3800+ Athlon64FX 53, or higher CPU
(For the latest information about CPU, please visit http://www.msi.com.tw/program/
products/mainboard/mbd/pro_mbd_cpu_support.php)
Chipset
† nVIDIA nForce3 Ultra
- HyperTransport link to the AMD Athlon 64/Athlon 64 FX CPU
- HyperTransport supporting speed up to 1GHz (2000MT/s)
- AGP3.0 8X interface at 533 MT/s (million transfers per second)
- Two independent SATA controllers, for four drives
- IEEE 802.3 nVIDIA MAC for 1000BASE-T
- Dual Fast ATA-133 IDE controllers
Main Memory
† Supports dual channel, eight memory banks DDR 266/333/400, using four 184-
pin DDR DIMMs
† Supports a maximum memory size up to 4GB with ECC
† Supports 2.5v DDR SDRAM DIMM
(For the updated supporting memory modules, please visit http://www.msi.com.tw/
program/products/mainboard/mbd/pro_mbd_trp_list.php.)
Slots
† One AGP (Accelerated Graphics Port) slot
- AGP specification compliant
- Supports AGP 3.0 8x
† Five 32-bit Master PCI Bus slots, includes one orange slot which is reserved as
a communication slot.
† Support 3.3V/5V PCI bus Interface
On-Board IDE
† An IDE controller on the nVIDIA ® nForce3 Ultra chipset provides IDE HDD/CD-
ROM with PIO, Bus Master and Ultra DMA 66/100/133 operation modes
† Can connect up to 4 IDE devices
On-Board SATA
† Supports 4 SATA ports. Transfer rate is up to 150MB/s.
USB Interface
† 8 USB ports
- Controlled by nForce3 Ultra chipset
- 4 ports in the rear I/O, 4 ports via the external bracket
E-1-4
Getting Started
NV RAID (Software)
h Supports up to 4 SATA and 4 ATA133 Hard drives
- RAID 0 or 1, 0+1, JBOD is supported
- RAID function available for ATA133+SATA H/D drives
LAN
h Supports dual LAN jacks
- 1st LAN supports 10/100/1000 Fast Ethernet by Marvell 88E1111
- 2nd LAN supports 10/100/1000 Fast Ethernet by Realtek 8110S (1000Mbps)
(Optional)
IEEE 1394
h Supports up to three 1394 ports (rear panel x 1, pinheader x 2). Transfer rate
is up to 400Mbps
Audio
h Chip integrated by Realtek ALC850 (7.1 ch H/W audio)
- Direct Sound AC97 audio
- 7.1 Channel output
- 1 CD-In
On-Board Peripherals
h On-Board Peripherals include:
- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes
- 1 serial port (COMA )
- 1 parallel port supporting SPP/EPP/ECP mode
- 1 Audio jack(5-in-1), coaxial/fiber SPDIF out
- 1 IrDA pinheader
- 1 D-Bracket2 pinheader
- 3 IEEE1394s (Rear * 1 / Front * 2)
- 8 USB1.1/2.0 ports (Rear * 4 / Front * 4)
BIOS
h The mainboard BIOS provides “Plug & Play” BIOS which detects the peripheral
devices and expansion cards of the board automatically.
h The mainboard provides a Desktop Management Interface (DMI) function which
records your mainboard specifications.
h Supports boot from LAN, USB Device 1.1 & 2.0, and SATA HDD.
E-1-5
MS-7025 ATX Mainboard
Dimension
† ATX Form Factor (30.4 cm X 24.4 cm)
Mounting
† 9 mounting holes
E-1-6
Getting Started
Mainboard Layout
SFA N2
Top : mouse
Bottom: keyboard
JPW1
JC I1
DIMM4
DIMM3
Top : Parallel Port
DIMM2
Bottom:
COM A
1394 Port DIMM1
SPDIF
Winbond
W83627HF
ID E 2
ID E 1
ATX1
T: LAN jack
B: USB ports
FDD 1
T: LAN jack
B: USB ports
T:Line-In
M:Line-Out
B: Mic
C PUFAN1
T:RS-Out
88E1111- RCJ
M:CS-Out SATA3
B:SPDIFOut
NBFAN1
SATA4
AGP1
NVIDIA
nFORCE3
PCI Slot2 Ultra SATA2
SATA1
PCI Slot3
BATT
+
SFA N1
PCI Slot 4
BIOS
VIA
VT6306
Codec
PCI Slot 5
JDB1
JBAT1
JA UD1
E-1-7
Hardware Setup
Hardware Setup
This chapter tells you how to install the CPU, memory modules,
and expansion cards, as well as how to setup the jumpers on the
mainboard. Also, it provides the instructions on connecting the periph-
eral devices, such as the mouse, keyboard, etc.
While doing the installation, be careful in holding the compo-
nents and follow the installation procedures.
E-2-1
MS-7025 ATX Mainboard
JPW1, p.2-10
SFAN2, p.2-16
CPUFAN1, p.2-16
JCI1, p.2-17
DDR DIMMs,
p.2-7
Back Panel
I/O, p.2-12 IDE1/2, p.2-17
ATX1, p.2-10
FDD1, p.2-16
SATA2, SATA1,
p.2-18
BATT
+
JDB1, p.2-21
JAUD1, p.2-20
JIR1, p.2-21
JCD1, p.2-18
JFP1, p.2-19
JBAT1, p.2-24 JFP2, p.2-19
E-2-2
Hardware Setup
E-2-3
MS-7025 ATX Mainboard
Gold arrow
E-2-4
Hardware Setup
1. Detach the shield of the backplate’s 3. Turn over the mainboard again, and
paster. place the mainboard on the flat
surface.
retention mechanism
E-2-5
MS-7025 ATX Mainboard
5. Position the cooling set onto the re- 7. Fastened down the lever.
tention mechanism.
While disconnecting the Safety Hook from the fixed bolt, it is neces-
sary to keep an eye on your fingers, because once the Safety Hook is
disconnected from the fixed bolt, the fixed lever will spring back instantly.
E-2-6
Hardware Setup
Memory
The mainboard provides 4 slots for 184-pin DDR SDRAM DIMM (Double In-Line Memory
Module) modules and supports the memory size up to 4GB. You can install DDR266/
333/400/433/466/500/533 modules on the DDR DIMM slots (DDR 1~4).
For the updated supporting memory modules, please visit http://www.msi.com.tw/
program/products/mainboard/mbd/pro_mbd_trp_list.php.
DIMM1~4
(from bottom to top)
E-2-7
MS-7025 ATX Mainboard
E-2-8
Hardware Setup
Volt Notch
E-2-9
MS-7025 ATX Mainboard
Power Supply
The mainboard supports ATX power supply for the power system. Before inserting
the power supply connector, always make sure that all components are installed
properly to ensure that no damage will be caused.
E-2-10
Hardware Setup
Figure 1:
Unplug the AC power cable
Figure 2:
Figure 3:
Unplug the ATX1 power connector
Unplug the JPW1 power connector
E-2-11
MS-7025 ATX Mainboard
Back Panel
L-In RS-Out
Parallel
Mouse LAN LAN
Pin Definition
6 5 PIN SIGNAL DESCRIPTION
IEEE1394 Port
E-2-12
Hardware Setup
Pin Definition
1 2 3 4 5 PIN SIGNAL DESCRIPTION
USB Connectors
The mainboard provides two OHCI (Open Host Controller Interface) Universal Serial
Bus roots for attaching USB devices such as keyboard, mouse or other USB-com-
patible devices. You can plug the USB device directly into the connector.
E-2-13
MS-7025 ATX Mainboard
S/PDIF Out-Coaxial
Center/Subwoofer
Line Out
Speaker Out
( in 7.1CH / 6CH)
E-2-14
Hardware Setup
13 1
25 14
Pin Definition
PIN SIGNAL DESCRIPTION
1 STROBE Strobe
2 DATA0 Data0
3 DATA1 Data1
4 DATA2 Data2
5 DATA3 Data3
6 DATA4 Data4
7 DATA5 Data5
8 DATA6 Data6
9 DATA7 Data7
10 ACK# Acknowledge
11 BUSY Busy
12 PE Paper End
13 SELECT Select
14 AUTO FEED# Automatic Feed
15 ERR# Error
16 INIT# Initialize Printer
17 SLIN# Select In
18 GND Ground
19 GND Ground
20 GND Ground
21 GND Ground
22 GND Ground
23 GND Ground
24 GND Ground
25 GND Ground
E-2-15
MS-7025 ATX Mainboard
Connectors
The mainboard provides connectors to connect to FDD, IDE HDD, case, LAN, USB
Ports, IR module and CPU/System FAN.
FDD1
E-2-16
Hardware Setup
IDE2 IDE1
E-2-17
MS-7025 ATX Mainboard
SATA3
SATA4 SATA1~ SATA4 Pin Definition
7 1 PIN SIGNAL PIN SIGNAL
E-2-18
Hardware Setup
E-2-19
MS-7025 ATX Mainboard
Pin Definition
IEEE1394 Bracket
Foolproof Design
(the 1394 pinheader in GREEN color)
E-2-20
Hardware Setup
D-Bracket™ 2
Connected to JDB1 (Optional)
E-2-21
MS-7025 ATX Mainboard
1 2
D-Bracket™ 2 3 4
Red Green
D-Bracket™ 2 Description
System Power ON
1 2
The D-LED will hang here if the processor is damaged or
3 4
not installed properly.
E-2-22
Hardware Setup
D-Bracket™ 2 Description
Processor Initialization
1 2
This will show information regarding the processor (like
3 4
brand name, system bus, etc...)
BIOS Sign On
This will start showing information about logo, proces-
sor brand name, etc...
Boot Attempt
This will set low stack and boot via INT 19h.
E-2-23
MS-7025 ATX Mainboard
Jumpers
The motherboard provides the following jumpers for you to set the computer’s
function. This section will explain how to change your motherboard’s function through
the use of jumpers.
Clear CMOS Jumper: JBAT1
There is a CMOS RAM on board that has a power supply from external battery
to keep the system configuration data. With the CMOS RAM, the system can auto-
matically boot OS every time it is turned on. If you want to clear the system
configuration, use the JBAT1 (Clear CMOS Jumper ) to clear data. Follow the instruc-
tions below to clear the data:
3
1 Keep Data Clear Data
1
JBAT1
E-2-24
Hardware Setup
Slots
The mainboard provides one AGP slot and five 32-bit PCI bus slots.
AGP Slot
PCI Slots
E-2-25
BIOS Setup
BIOS Setup
This chapter provides information on the BIOS Setup program and allows
you to configure the system for optimum use.
E-3-1
MS-7025 ATX Mainboard
Entering Setup
Power on the computer and the system will start POST (Power On Self Test) process.
When the message below appears on the screen, press <DEL> key to enter Setup.
If the message disappears before you respond and you still wish to enter Setup,
restart the system by turning it OFF and On or pressing the RESET button. You may
also restart the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
The POST messages might pass by too quickly for you to respond in time. If so,
restart the system and press <F11> after around 2 or 3 seconds to activate the boot
menu similar to the following.
The boot menu will list all the bootable devices. Select the one you want to boot from
by using arrow keys, then press <Enter>. The system will boot from the selected
device. The selection will not make changes to the settings in the BIOS setup utility,
so next time when you power on the system, it will still use the original first boot
device to boot up.
MSI Reminds You...
The items under each BIOS category described in this chapter are
under continuous update for better system performance. Therefore,
the description may be slightly different from the latest BIOS and
should be held for reference only.
E-3-2
BIOS Setup
Control Keys
Getting Help
After entering the Setup menu, the first menu you will see is the Main Menu.
Main Menu
The main menu lists the setup functions you can make changes to. You can use
the arrow keys ( ↑↓ ) to select the item. The on-line description of the highlighted
setup function is displayed at the bottom of the screen.
Sub-Menu
If you find a right pointer symbol (as shown in the right view) appears to the left
of certain fields that means a sub-menu can be launched from this field. A sub-
menu contains additional options for a field
parameter. You can use arrow keys ( ↑↓ ) to
highlight the field and press <Enter> to call up
the sub-menu. Then you can use the control
keys to enter values and move from field to
field within a sub-menu. If you want to return
to the main menu, just press the <Esc >.
E-3-3
MS-7025 ATX Mainboard
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
PNP/PCI Configurations
This entry appears if your system supports PnP/PCI.
H/W Monitor
Use this menu to specify your settings for hardware.
Cell Menu
Use this menu to specify your settings for CPU/AGP frequency/voltage control and
overclocking.
E-3-4
BIOS Setup
E-3-5
MS-7025 ATX Mainboard
Cell Menu
The items in Cell Menu includes some important settings of CPU, AGP, DRAM
and overclocking functions.
DRAM Configuration
Press <Enter> to enter the sub-menu and the following screen appears:
E-3-6
BIOS Setup
Aggressive Timing
This item allows you to enable or disable the memory clock. When [Enabled] is selected,
the timing delay of memory will be shorten to increase the performance. Setting
options: [Enabled], [Disabled].
Dynamic Overclocking
Dynamic Overclocking Technology is the automatic overclocking function, included in
the MSI TM ’s newly developed CoreCellTM Technology. It is designed to detect the load
balance of CPU while running programs, and to adjust the best CPU frequency
automatically. When the motherboard detects CPU is running programs, it will speed
up CPU automatically to make the program run smoothly and faster. When the CPU is
temporarily suspending or staying in the low load balance, it will restore the default
settings instead. Usually the Dynamic Overclocking Technology will be powered only
when users' PC need to run huge amount of data like 3D games or the video process,
and the CPU frequency need to be boosted up to enhance the overall performance.
E-3-7
MS-7025 ATX Mainboard
Setting options:
[Disabled] Disable Dynamic Overclocking.
[Private] 1st level of overclocking, increasing the CPU frequency by 1%.
[Sergeant] 2nd level of overclocking, increasing the CPU frequency by 3%.
[Captain] 3rd level of overclocking, increasing the CPU frequency by 5%.
[Colonel] 4th level of overclocking, increasing the CPU frequency by 7%.
[General] 5th level of overclocking, increasing the CPU frequency by 9%.
[Commander] 6th level of overclocking, increasing the CPU frequency by 11%.
Spread Spectrum
This setting is used to enable or disable the FSB clock generator’s Spread Spectrum
feature. When overclocking the FSB, always set it to [Disabled]. Setting options:
[Enabled], [Disabled].
HT Frequency
This setting specifies the maximum operating frequency of the link’s transmitter clock.
Setting options: [1x], [2x], [3x], [4x], [5x].
Cool’n’Quiet control
This feature is especially designed for AMD Athlon processor, which provides a CPU
temperature detecting function to prevent your CPU’s from overheating due to the
heavy working loading. Setting options: [Disabled], [Auto].
E-3-8
BIOS Setup
CPU Voltage
The settings are used to adjust the CPU clock multiplier (ratio) and CPU core voltage
(Vcore). These settings offer users a tool to overclock the system.
Memory Voltage
Adjusting the DDR voltage can increase the DDR speed. Any changes made to this
setting may cause a stability issue, so changing the DDR voltage for long-term
purpose is NOT recommended.
AGP Voltage
AGP voltage is adjustable in the field, allowing you to increase the performance of
your AGP display card when overclocking, but the stability may be affected.
E-3-9
Manuel d’utilisation
K8N Neo 2
(MS-7025 v1.X)
ATX mainboard
Français
F-1
F-1
Carte M ère ATX MS-7025
F-2
Manuel d’utilisation
Chap t er 1 . Ge tting
StartedK8N Neo2
Manuel d’utilisation
F-3
Carte M ère ATX MS-7025
Spécificités de la Carte
CPU
† Supporte les processeurs Socket-939 pour AMD K8 Athlon 64 FX / Athlon 64
(Socket939)
† Supporte jusqu’à 3500+, 3800+ Athlon64FX 53, ou supérieur
(Pour connaître les dernières informations au sujet du CPU, veuillez visiter http://
www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support.php)
Chipset
† nVIDIA nForce3 Ultra
- Lien HyperTransport vers le CPU AMD Athlon 64/Athlon 64 FX
- HyperTransport supportant une vitesse maximale de 1GHz (2000MT/s)
- Interface AGP3.0 8X à 533 MT/s (million de transferts par seconde)
- 2 contrôleurs SATA indépendants, pour quatre disques
- IEEE 802.3 nVIDIA MAC pour 1000BASE-T
- Double contrôleur Dual Fast ATA-133 IDE
Mémoire Principale
† Support du double canal, 8 banques de mémoire DDR 266/333/400 (184 broches)
† Supporte un maximum de mémoire jusqu’à 4GB avec ECC
† Supporte 2.5v DDR SDRAM DIMM
(Pour une mise à jours sur les modules de mémoire supportés, veuillez visiter http://
www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php.)
Slots
† Un slot AGP (Accelerated Graphics Port)
- Compatible avec les spécifications de l’AGP
- Supporte l’AGP 3.0 8x
† Cinq slots 32-bit Master PCI Bus, un slot orange réservé en tant que slot de
communication
† Support 3.3V/5V PCI bus Interface
IDE Intégré
† Un contrôleur IDE intégré sur le chipset nVIDIA ® nForce3 Ultra procure IDE HDD/
CD-ROM avec PIO, Bus Master et les modes opératoires Ultra DMA 66/100/133
† Possibilité de connecter jusqu’à 4 matériels IDE
SATA Intégré
† Supporte 4 ports SATA. Taux de transfert allant jusqu’à 150MB/s.
Interface USB
† 8 ports USB
- Controllé par le chipset nForce3 Ultra
- 4 ports r l’arricre (I/O), 4 ports via le bracket externe
F-4
Manuel d’utilisation
NV RAID (Logiciel)
h Supporte jusqu’à 4 disques durs SATA et 4 ATA133
- RAID 0 ou 1, 0+1, JBOD est supporté
- Fonction RAID fonctionnant avec disques durs ATA133+SATA
LAN
h Supporte le double LAN
- 1er LAN 10/100/1000 Fast Ethernet par Marvell 88E1111
- 2ème LAN 10/100/1000 Fast Ethernet par Realtek 8110S (1000Mbps)(Optionnel)
IEEE 1394
h Supporte jusqu’à trois ports 1394 (panneau arrière x 1, broches sur la cartex 2).
Taux de transfert jusqu’à 400Mbps
Audio
h Chip intégré - Realtek ALC850 (7.1 ch H/W audio)
- Direct Sound AC97 audio
- 7.1 canaux en sortie
- 1 CD-In
Périphériques Intégrés
h Les périphériques intégrés sont:
- 1 port floppy supportant 1 FDD avec 360K, 720K, 1.2M, 1.44M et 2.88Mbytes
- 1 port série (COMA )
- 1 port parallèle supportant les modes SPP/EPP/ECP
- 1 jack audio (5-en-1), coaxial/fibre SPDIF en sortie
- 1 série de broches IrDA
- 1 série de broches pour D-Bracket2
- 3 IEEE1394a (Arrière * 1 / Façade * 2)
- 8 ports USB1.1/2.0 (Arrière * 4 / Façade * 4)
BIOS
h la carte mère procure un BIOS “Plug & Play” qui détecte automatiquement les
périphériques et les cartes d’extensions.
h La carte procure une fonction d’interface DMI (Desktop Management Interface)
qui enregistre les spécifications de la carte.
h Support boot à partir de matériels LAN, USB 1.1 & 2.0, et SATA HDD.
F-5
Carte M ère ATX MS-7025
Dimension
† Format ATX (30.4 cm X 24.4 cm)
Moontage
† 9 mounting holes
F-6
Manuel d’utilisation
Schéma de la Carte
2 4 4
SFAN2
Top : mouse
Bottom: keyboard
JPW1
JCI1
DIMM4
DIMM3
Top : Parallel Port
Bottom:
DIMM2 8
COM A
1394 Port DIMM1
SPDIF
6
Winbond
W83627HF
IDE 2
IDE 1
ATX1
T: LAN jack
B: USB ports
FDD 1
T: LAN jack 1
B: USB ports
T:Line-In
M:Line-Out
B:M i c
CPUFAN1
T:RS-Out
88E1111-RCJ
3
M:CS-Out SATA3
B:SPDIFOut
NBFAN1
SATA4 4
AGP1
5
16 5
RTL8110S-32 PCI Slot 1
NVIDIA
nFORCE3
PCI Slot2 Ultra
SATA2
SATA1
17
PCI Slot3
6
BATT
+
PCI Slot 4
SFAN1
4
BIOS
VIA
VT6306
Codec
PCI Slot 5
JDB1
10
JAUD1
JBAT1
14
9
15 8 8 12
13 11
F-7
Carte Mère ATX MS-7025
3. Connecteur d’Alimentation Floppy Disk Drive : FDD1. La carte est pourvue d’un
connecteur de disquette qui supporte les disques de 360K, 720K, 1.2M, 1.44M et
2.88M.
5. Connecteurs ATA133 Hard Disk : IDE1/IDE2. This mainboard has a 32-bit En-
hanced PCI IDE and Ultra DMA 66/100/133 controller that provides PIO mode 0~4,
Bus Master and Ultra DMA 66/100/133 function.
6. C o n n e c t e u r s S e r i a l ATA / S e r i a l ATA R A I D c o n t r ô l é s p a r
nForce3 Ultra: SATA1 / SATA2 / SATA3 / SATA4. Le Southbridge de cette carte
mère est un nForce3 Ultra qui supporte deux connecteurs Serial : SATA1 et
SATA2. Ce sont des ports à interface grande vitesse double.
7 1 9 1 JFP1
JFP2 8 2 10 2
F-8
Manuel d’utilisation
11. Connecteurs Front USB : JUSB1/JUSB2. La carte procure deux séries de broches
pour la connexion USB2.0.
12. Module infra Rouge IrDA : JIR1. Ce connecteur permet de la mise en place d’un
module infra rouge. Il faudra configurer leBIOS pour utiliser cette fonction.
13. Connecteur IEEE 1394 : J1394_1/J1394_2. La carte offre deux séries de broches
pour la connexion 1394 via un bracket externe (optionnel).
14. Connecteur Front Panel Audio : JAUD1. Le connecteur JAUD1 permet la connexion
au front panel audio qui est compatible avec l’Intel® Front Panel I/O Connectivity
Design Guide.
15. Cavalier Clear CMOS : JBAT1. Une batterie doit être utilisée afin de retenir la
configuration du système paramètrée dans la RAM CMOS. Placez un cavalier sur
les broches 1-2 de JBAT1 afin de conserver les données du CMOS.
16. Slot AGP (Accelerated Graphics Port). Le slot AGP permet la mise en placed ‘une
carte graphique. L’interface AGP est destiné à répondre aux demandes 3D. Le
slot supporte les cartes AGP 4 et 8x.
17. Slots PCI (Peripheral Component Interconnect). Les slots PCI vous permettent
d’ajouter des cartes d’extensions. Lors de la l’ajout ou quand vous démontez
une carte PCI assurez-vous tout d’abord que le PC n’est plus sous tension.
Pour la configuration des cartes PCI, veuillez vous reporter au manuelm
fournit avec votre matériel. ilo est parfois nécessaire de configurer le BIOS
pour que la carte PCI soit fonctionnelle.
Le slot PCI orange (PCI5) fonctionne aussi comme slot de communication, ce
qui vous permet d’y insérer une carte de communication de MSI pour le W ifi
(réseau sans fil) par exemple.
F-9
Carte M ère ATX MS-7025
F-10
Manuel d’utilisation
Open Lever
Sliding
1. Veuillez éteindre et débrancher Plate
90 degree
votre PC avant l’installation du
CPU.
F-11
Carte M ère ATX MS-7025
Mécanisme de Rétention
F-12
Manuel d’utilisation
Levier Verrou
de fixation
F-13
Carte M ère ATX MS-7025
Mémoire
La carte offre 4 slots pour DDR SDRAM DIMM (Double In-Line Memory Module) 184
broches et supporte un maximum de mémoire de 4GB. Vous pouvez installer des
modules DDR266/ 333/400/433/466/500/533 sur les slots DDR DIMM (DDR 1~4).
Pour une mise r jour sur les modules de mémoire, veuillez visiter http://www.msi.
com.tw/program/products/mainboard/mbd/pro_mbd_trp_list.php.
DIMM1~4
(du bas vers le haut)
F-14
Manuel d’utilisation
F-15
Carte M ère ATX MS-7025
Volt Encoche
F-16
Manuel d’utilisation
Setup du BIOS
Allumez votre ordinateur, le système lance le processus de POST (Power On Self
Test). Quand le message ci-dessous apparaît à l’écran, appuyez sur le bouton <DEL>
pour entrer dans le setup.
Appuyez sur DEL pour accéder au SETUP
ISi le message disparaît avant que vous ne puissiez entrer dans le setup, redémarrez
votre ordinateur en appuyant sur le bouton RESET. Vous pouvez aussi utiliser
simultanément la combinaison de touches : <Ctrl>, <Alt>, et <Delete>.
Choix du Premier Elément de Boot
Vous pouvez choisir le premier élément de boot sans entrer dans le setup, pour cela il
suffit d’appuyer sur la touche <F11> quand le message apparaît à l’écran.
Le message de POST passe très rapidement, si vous n’avez pas le temps d’appuyer
sur la touche <F11>, redémarrez votre PC et appuyez de nouveau sur <F11> pendant
2 ou 3 secondes pour activer le menu de boot comme indiqué ci-dessous.
Le menu de boot va vous indiquer tous les éléments qui peuvent être selectionnés.
Choisir celui que vous voulez en utilisant les flèches pour vous déplacer et en
appuaynt sur <Enter> pour selectionner. Les système va alors booter à partir de cet
élément. Cela ne change rien aux éléments du BIOS, le seul changement est que lors
du prochain démarrage, le boot se fera à partir de cet élément.
F-17
Carte M ère ATX MS-7025
Menu Principal
Une fois entré dans le BIOS Phoenix-Award® CMOS Setup Utility, Le menu
apparaît à l’écran. Le Menu permet de sélectionner douze fonctions et deux choix de
choix de sortie de l’utilitaire. Utilisez les flèches pour vous diriger et utilisez la touche
ENTREE pour sélectionner un élément ou entrer dans le sous-menu.
Integrated Peripherals
Utilisez ce menu pour changer les choix relatifs aux périphériques intégrés.
PNP/PCI Configurations
Apparaît si votre systcme supporte PNP/PCI.
H/W Monitor
Voir les statuts des CPU, ventilateur, et alarme système.
Cell M enu
Utilisez ce menu pour spécifier vos paramètres pour la fréquence et le voltage des
CPU/DRAM/AGP.
F-18
Manuel d’utilisation
F-19
Carte M ère ATX MS-7025
Menu Cell
Vous pouvez dans ce menu gérer d’importantes fonctions du CPU, AGP, DRAM et
d’overclocking.
DRAM Configuration
Pressez <Enter> pour entrer dans le sous-menu et suivez l’écran ci-après:
F-20
Manuel d’utilisation
Détermine le temps RAS pour lire et écrire une cellule mémoire. Options: [Auto], [5],
[6], [7], [8], [9], [10], [11], [12], [13], [14], [15].
Aggressive Timing
Cet élément permet d’activer/désactiver l’horloge mémoire. Quiand [Enabled] est
selectionné, le temps d’attente de la mémoire sera diminué afin d’accroître les
performances. Les paramètres sont : [Enabled], [Disabled].
Dynamic Overclocking
Le DOT (Dynamic Overclocking Technology) est une fonction overclocking automatique
inclut dans la nouvelle technologie CoreCellTM développée par MSITM. Déstiné r détecter
la charge de travail du CPU lors de l’utilisation de programmes, le DOT permet
d’augmenter la fréquence du CPU automatiquement afin que le programme soit utilisé
dans les meilleures conditions. Quand le CPU ne travaille pas ou que son activité est
faible alors les paramctres par défaut sont utilisés. En rcgle général, le DOT se met en
action lorsque la demande en puissance est importante comme lorsque vous utilisez
des jeux 3D. Les options sont :
[Disabled] Désactive la fonction DOT.
[Private] 1er niveau d’overclocking, augmentant la fréquence CPU de 1%.
F-21
Carte M ère ATX MS-7025
Spread Spectrum
Ce paramètre permet d’activer/désactiver la fonction de Spread Spectrum. Lorsque
vous faites de l’overclocking sur le FSB, veuillez toujours sélectionner [Disabled].
Les options : [Enabled], [Disabled].
HT Frequency
Ce paramètre spécifie la fréquence maximale d’exploitation. Les options: [1x], [2x],
[3x], [4x], [5x].
Cool’n’Quiet control
Cette fonction est exclusivement réservée aux processeurs AMD Athlon, elle pro-
cure une fonction de détection de la température du CPU permettant ainsi d’éviter la
surchauffe. Les options: [Disabled], [Auto].
F-22
Manuel d’utilisation
CPU Voltage
Cet élément vous permet de changer le voltage CPU.
Memory Voltage
Modifier le voltage DDR peut augmenter la vitesse de la DDR. Tous les changements
peuvent entraîner une instabilité, par conséquent l’utilisation d’un paramètre modifié e
doit pas se faire de façon défintive mais temporaire.
AGP Voltage
Le voltage AGP est modifiable, ce qui vous permet d’augmenter la performance la
carte graphique lors de l’overclocking, mais la stabilité n’est pas assurée.
F-23
Benutzerhandbuch
K8N Neo 2
(MS-7025 v1.X)
ATX mainboard
Deutsch
G-1
G-1
MS-7025 ATX Mainboard
G-2
Benutzerhandbuch
G-3
MS-7025 ATX Mainboard
Mainboard Spezifikationen
CPU
† Unterstützt AMD K8 Athlon 64 FX / Athlon 64 Prozessoren für den Sockel 939
† Unterstützt CPUs bis hin zu den 3500+ und 3800+ Athlon64FX 53, oder höher
(Bitte besuchen http://www.msi.com.tw/program/products/mainboard/mbd/
pro_mbd_cpu_support.php um die neuesten Informationen zu unterstützten
Prozessoren zu erhalten)
Chipset
† nVIDIA nForce3 Ultra
- Anbindung der AMD Athlon 64/Athlon 64 FX CPU über HyperTransport
- HyperTransport erlaubt Geschwindigkeiten von bis zu 1GHz (2000MT/s)
- AGP3.0 8X Schnittstelle mit 533 MT/s (Millionen Ü bertragungen pro Sekunde)
- Zwei unabhängige SATA-Controller, bis zu 4 Laufwerke
- nVIDIA IEEE 802.3 Media Access Control (MAC) für 1000BASE-T
- Zweikanal ATA-133 IDE Kontroller
Hauptspeicher
† Unterstützt acht Zweikanal DDR 266/333/400 Speicherbänke, zum Einsatz von
vier 184-Pin DDR SDRAM DIMMs
† Unterstützt einen maximalen Speicherausbau von bis zu 4GB mit ECC
† Unterstützt 2,5V DDR SDRAM DIMM
(Den letzten Stand bezüglich der unterstützten Speichermodule finden Sie unter
http://www.msi.com.tw/program/products/mainboard/mbd/ pro_mbd_trp_list.php.)
Schnittstellen
† Eine AGP (Accelerated Graphics Port) Schnittstelle
- Erfüllt die AGP Spezifikationen
- Bietet AGP 3.0 8-fach
† Fünf 32-bit Master PCI Bus Steckplätze, ein orangefarbener als Kommunikationsslot
reserviert
†3.3V/5V PCI Bus unterstützt
On-Board IDE
®
† Der im nVIDIA nForce3 Ultra Chipsatz enthaltene IDE Kontroller bietet für den
Festplatten- und CD-ROM-Zugriff PIO, Bus Mastering und Betrieb mit Ultra DMA
66/100/133
† Bis zu 4 IDE Geräte anschließ bar
On-Board SATA
† Bis zu 4 SATA Laufwerke anschliessbar, Ü bertragungsrate von bis zu 150 MB/s
USB Schnittstellen
† 8 USB Anschlüsse
- Gesteuert vom nForce3 Ultra Chipsatz
- 4 Anschlüsse im hinteren Ein-/Ausgangssegment, 4 Anschlüsse über ein externes
Slotblech
G-4
Benutzerhandbuch
NV RAID (Software)
Unterstützt bis zu 4 SATA und 4 ATA 133 Laufwerk
- RAID 0, 1, 0+1 oder den Betrieb ohne RAID-Funktionalität
- RAID-Funktionalität mit ATA133 und SATA Festplatten
LAN
Bietet zwei LAN- Anschlüsse
- Der erste LAN- Anschluss unterstützt 10/100/1000 Fast Ethernet entweder
auf Basis des Marvell 88E1111
- Der zweite LAN- Anschluss unterstützt 10/100/1000 Fast Ethernet entweder
auf Basis des Realtek 8110S (1000Mbps)(Optional)
IEEE 1394
Unterstützt bis zu drei 1394 Schnittstellen (einmal via hinteres Anschlussegment,
zweimal als Stiftleiste auf dem Motherboard). Die Übertragungsgeschwindigkeit
beträgt bis zu 400 MB/s
Audio
In den Chip Realtek ALC850 integriert (7.1 Kanal Hardwareaudio)
- Direct Sound AC97 Audio
- 7.1 Kanalausgabe
- CD Eingang
Peripherieanschlüsse onboard
hierzu gehören:
- 1 Anschluss für ein Diskettenlaufwerke mit 360 KB, 720 KB, 1,2 MB, 1,44 MB
oder 2,88 MB
- 1 Serielle Schnittstelle (COMA)
- 1 Parallele Schnittstelle, die die Betriebsmodi SPP/EPP/ECP unterstützt
- 1 Audioanschluss (5 in 1), koaxialer/Fiberglass SPDIF Ausgang
- 1 IrDA Stiftleiste
- 1 D-Bracket 2 Stiftleiste
- 3 IEEE1394a Anschlüsse (1 hinterer/ 2 vordere)
- 8 USB1.1/2.0 Anschlüsse (4 hinterer/ 4 vordere)
BIOS
Das Mainboard-BIOS verfügt über “Plug & Play”-Funktionalität, mit der
angeschlossene Peripheriegeräte und Erweiterungskarten automatisch erkannt
werden.
Das Mainboard stellt ein Desktop - Management - Interface (DMI) zur Verfügung,
welches automatisch die Spezifikationen Ihres Mainboards aufzeichnet.
Unterstützt das Booten über Netzwerk, von USB 1.1 und 2.0 Laufwerken und
SATA Festplatte.
G-5
MS-7025 ATX Mainboard
Abmessungen
† ATX Form Faktor (30,4 cm x 24,4 cm)
Montage
† 9 Montagebohrungen
G-6
Benutzerhandbuch
Mainboard Layout
2 4 4
SFAN2
Top : mouse
Bottom: keyboard
JPW1
7
JCI1
DIMM4
DIMM3
Top : Parallel Port
Bottom:
DIMM2 8
COM A
1394 Port DIMM1
SPDIF
6
Winbond
W83627HF
IDE 2
IDE 1
ATX1
T: LAN jack
B: USB ports
FDD 1
T: LAN jack 1
B: USB ports
T:Line-In
M:Line-Out
B:M i c
CPUFAN1
T:RS-Out
88E1111-RCJ
3
M:CS-Out SATA3
B:SPDIFOut
NBFAN1
SATA4 4
AGP1 5
16 5
RTL8110S-32 PCI Slot 1
NVIDIA
nFORCE3
PCI Slot2 Ultra
SATA2
SATA1
17
PCI Slot3
BATT
+ 6
PCI Slot 4
SFAN1
4
BIOS
VIA
VT6306
Codec
PCI Slot 5
JDB1
10
JAUD1
JBAT1
14
9
15 8 8 12
13 11
G-7
MS-7025 ATX Mainboard
JFP2 7 1 9 1 JFP1
8 2 10 2
9. CD-In Eingang: JCD1. Hier kann das Audiokabel des CD-ROM Laufwerkes
angeschlossen werden.
10. D-Bracket™ 2 Anschluss: JDB1. Dient zum Anschluss der D-Bracket™ 2.
Hierbei handelt es sich um ein USB Slotblech, das den Spezifikationen USB1.1
und 2.0 genügt.
G-8
Benutzerhandbuch
G-9
MS-7025 ATX Mainboard
Hauptprozessor: CPU
Das Mainboard arbeitet mit AMD ® Athlon 64 und Athlon 64 FX Prozessoren. Hierbei
setzt das Mainboard den CPU Sockel 939 ein, um den CPU-Einbau zu erleichtern.
Achten Sie beim Einbau bitte darauf, dass die CPU immer mit einem aktiven
Prozessorlüfter mit Kühlkörper versehen sein muss, um Ü berhitzung zu
vermeiden. Verfügen Sie über keinen aktiven Prozessorlüfter mit Kühlkörper, setzen
Sie sich bitte mit Ihrem Händler in Verbindung, um einen solchen zu erwerben und
danach zu installieren, bevor Sie Ihren Computer anschalten.
Bitte besuchen http://www.msi.com.tw/program/products/mainboard/mbd/
pro_mbd_cpu_support.php , um die neuesten Informationen zu unterstützten
Prozessoren zu erhalten
Ü berhitzung
Ü berhitzung beschädigt die CPU und das System nachhaltig, stellen
Sie stets eine korrekte Funktionsweise des CPU Lüfters sicher, um
die CPU vor Ü berhitzung zu schützen.
Das System wird automatisch heruntergefahren und gesichert, falls es
zur Ü berhitzung der CPU kommt. In dieser Situation ist es nicht möglich,
das System zu starten. Um die Sicherheitsperre zu lösen, drücken und
halten Sie den Einschaltknopf für 4 Sekunden oder trennen Sie das
System vorübergehend vom Netz und führen Sie dann einen Neustart
durch.
Auswechseln der CPU
Stellen Sie während eines CPU-Wechsels immer sicher, dass das
ATX Netzteil ausgeschaltet ist und ziehen Sie zuerst den Netzstecker,
um die Unversehrtheit Ihrer CPU zu gewährleisten.
Ü bertakten
Dieses Motherboard wurde so entworfen, dass es Ü bertakten
unterstützt. Stellen Sie jedoch bitte sicher, dass die betroffenen
Komponenten in der Lage sind, solche abweichenden Einstellungen
zu vertragen, wenn Sie übertakten. Von jedem Versuch des Betriebes
ausserhalb der Produktspezifikationen kann nur abgeraten werden.
Wir ü bernehmen keinerlei Garantie für die Schäden und
Risiken, die aus unzulässigem Betrieb oder Betrieb jenseits der
Produktspezifikationen resultieren.
G-10
Benutzerhandbuch
Gold arrow
3. Suchen Sie nach einem goldenen
Pfeil. Der goldene Pfeil sollte auf
das Hebelgelenk zeigen. Die CPU
passt nur in der korrekten Aus-
richtung.
G-11
MS-7025 ATX Mainboard
1. Ziehen Sie die Schutzfolie von der 3. Drehen Sie das Mainboard wieder auf
Klebstoffschicht der Rückplatte ab. die Vorderseite und legen Sie es auf
einer ebenen Fläche ab.
Rückhaltemechanismus
G-12
Benutzerhandbuch
5. Setzen Sie den Kühler auf den 7. Drücken Sie den Sicherungshebel
Rückhaltemechanismus. herab.
Sicherungshebel Sicherungsbolzen
G-13
MS-7025 ATX Mainboard
Speicher
Das Mainboard bietet Platz für vier 184-pin DDR SDRAM DIMMs (Double In-Line Memory
Module) und unterstützt den Speicherausbau auf bis zu 4GB. Sie können DDR266/
333/400/433/466/500 oder 533 Module in die DDR DIMM Sockel einsetzen (DDR 1- 4).
Um den letzten Stand bezüglich der unterstützten Speichermodule zu erhalten,
besuchen Sie bitte http://www.msi.com.tw/program/products/mainboard/mbd/
pro_mbd_trp_list.php
DIMM1~4
(von oben nach unten)
DDR Speicherzusammensetzung
Setzen Sie mindestens ein Speichermodul in einen Stecksockel. Jeder DIMM Sockel
unterstützt einen Speicherriegel mit maximal 1 GB. Gemäß Ihren Anforderungen können
Sie entweder ein- oder doppelseitige Module verwenden. Bitte beachten Sie, dass
jedes DIMM jeweils im Einkanal- DDR- Betrieb verwendet werden kann,
jedoch einige Regeln beachtet werden müssen, falls Sie sie im
Zweikanalbetrieb verwenden wollen. (Entnehmen Sie bitte der Tabelle unten die
Vorschläge zur Speicherbestückung). Sie können Speicherriegel unterschiedlichen
Typs und unterschiedlicher Größe in unterschiedlichen Speicherkanälen verwenden.
Es kann jedoch zu Stabilitätsproblemen kommen, falls Sie nicht Module gleichen
Typs und gleicher Grö ß e im Zweikanalbetrieb verwenden. Bitte entnehmen Sie
der folgenden Tabelle detailliert geeignete Zweikanalanordnungen. Abweichende
Speicherzusammenstellungen, die unten nicht aufgeführt sind, funktionieren als
Einkanalspeicher.
G-14
Benutzerhandbuch
G-15
MS-7025 ATX Mainboard
Volt Kerbe
G-16
Benutzerhandbuch
BIOS Setup
Nach dem Einschalten beginnt der Computer den POST (Power On Self Test -
Selbstüberprüfung nach Anschalten). Sobald die Meldung unten erscheint, drücken
Sie die Taste <Entf>(<Del>) um das Setup aufzurufen.
Press DEL to enter SETUP
Wenn die Nachricht verschwindet, bevor Sie reagieren und Sie möchten immer noch
ins Setup, starten Sie das System neu, indem Sie es erst AUS- und danach wieder
ANSCHALTEN, oder die “RESET”-Taste am Gehäuse betätigen. Sie können das Sys-
tem außerdem neu starten, indem Sie gleichzeitig die Tasten <Strg>,<Alt> und <Entf>
drücken (bei manchen Tastaturen <Ctrl>,<Alt> und <Del>).
G-17
MS-7025 ATX Mainboard
Hauptmenü
Nachdem Sie das Phoenix-Award® BIOS CMOS Setup Utility, aufgerufen haben,
erscheint das Hauptmenü. Es weist zwölf Setup- Funktionen und zwei Arten das
Menü zu verlassen auf. Verwenden Sie die Pfeiltasten, um im Menü zu navigieren
und drücken Sie die Eingabetaste (<Enter>), um ein Untermenü aufzurufen.
Integrated Peripherals
Verwenden Sie dieses Menü, um die Einstellungen für in das Board integrierte
Peripheriegeräte vorzunehmen.
PNP/PCI Configurations
Dieser Eintrag erscheint, wenn Ihr System Plug and Play- Geräte am PCI-Bus
unterstützt.
G-18
Benutzerhandbuch
H/W Monitor
Erlaubt es, die Sollwerte für die Hardware festzulegen.
Cell Menu
In diesem Menü können Sie Einstellungen an Frequenz und Spannung, sowie
Ü bertaktungen der CPU und des AGP vornehmen.
G-19
MS-7025 ATX Mainboard
Cell Menu
Das “Cell Menu” beinhaltet einige wichtige Einstellungen für CPU, AGP und den
Speicher sowie zur Ü bertaktung.
DRAM Configuration
Drücken Sie die Eingabetaste (<Enter>) um das zugehörige Untermenü aufzurufen,
es erscheint folgender Bildschirm:
G-20
Benutzerhandbuch
Aggressive Timing
Hier kann die Speichertaktverkürzung ein- oder ausgeschaltet (Enabled/Disabled)
werden ein. Wird [Enabled] gewählt, wird die Taktlänge verkürzt um die Leistung zu
steigern. Die möglichen Einstellungen sind: [Enabled], [Disabled].
G-21
MS-7025 ATX Mainboard
Dynamic Overclocking
Dynamic Overclocking Technology ist die automatische Ü bertaktungsfunktion, die in
MSITM’s neu entwickelter CoreCellTM Technologie enthalten ist. Sie dient zur Feststellung
des Auslastungsgrades der CPU, während diese Programme abarbeitet, und passt
die CPU-Frequenz automatisch auf das optimale Niveau an. Stellt das Motherboard
fest, dass die CPU Programme ausführt, beschleunigt es automatisch die CPU und
erlaubt so eine flüssige und schnellere Ausführung. Ist die CPU ohne Last oder nur
wenig ausgelastet, werden statt dessen die Voreinstellungen wieder hergestellt.
Ü blicherweise kommt die Technologie der dynamischen Ü bertaktung nur zum Einsatz,
wenn groß e Datenmengen bewältigt werden müssen, wie das bei anspruchsvollen
3D Spielen oder der Videoverarbeitung der Fall ist. In diesen Fällen ist es notwendig,
die CPU -Frequenz zu erhöhen, um die Gesamtleistung des Systems zu erhöhen. Die
möglichen Einstellungen sind:
[Disabled] Dynamic Overclocking ist ausgeschaltet
[Private] Erste Ü bertaktungsstufe, steigert die CPU Frequenz um 1%.
[Sergeant] Zweite Ü bertaktungsstufe, steigert die CPU Frequenz um 3%.
[Captain] Dritte Ü bertaktungsstufe, steigert die CPU Frequenz um 5%.
[Colonel] Vierte Ü bertaktungsstufe, steigert die CPU Frequenz um 7%.
[General] Fünfte Ü bertaktungsstufe, steigert die CPU Frequenz um 9%.
[Commander] Sechste Ü bertaktungsstufe, steigert die CPU Frequenz um 11%.
Spread Spectrum
Schaltet die Spread Spectrum Funktion des Systembus (FSB) Taktgenerators ein-
oder aus (enabled/disabled). Wird der FSB übertaktet, muss die Einstellung aus
(“Disabled”) sein. Die möglichen Einstellungen sind: [Enabled], [Disabled].
HT Frequency
Diese Einstellung legt die maximale Betriebsfrequenz des Taktgenerators der
HyperTransport Verbindung fest. Die möglichen Einstellungen sind:: [1x], [2x], [3x],
[4x] und [5x].
G-22
Benutzerhandbuch
Cool’n’Quiet control
Wurde speziell für AMD Athlon Prozessoren entworfen und bietet eine
Funktion zur Feststellung der CPU Temperatur, die ein Ü berhitzen der CPU
aufgrund hohen Auslastungsgrades verhindert. Die möglichen Einstellungen
sind: [Disabled](ausgeschaltet), [Auto].
CPU Voltage
Diese Einstellungen werden verwendet, um den CPU-Taktmultiplikator und die
Kernspannung (Vcore) der CPU festzulegen und bieten dem Anwender ein Instrument,
das System zu übertakten.
Memory Voltage
Speicherspannung. Die Spannung des DDR anzuheben, kann diesen beschleunigen.
Jede Ä nderungn dieser Option kann zu Stabilitätsproblemen führen, deswegen wird
von einer langfristigen Ä nderung der DDR Spannung ABGERATEN.
AGP Voltage
Erlaubt die Anpassung der AGP Spannung und damit die Steigerung der Leistung der
AGP Grafikkarte beim Ü bertakten, jedoch möglicher Weise unter Beeinträchtigung
der Stabilität.
G-23