You are on page 1of 251

AT COMMANDS

INTERFACE GUIDE
confidential ©
This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged
without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut
être communiqué ou divulgué à des tiers sans son autorisation préalable.
AT COMMANDS
INTERFACE GUIDE
atVersion: 004
Date: April, 05th 2002
Reference: WM_SW_OAT_IFS_001
Contents

1 Introduction 1
1.1 Scope of this document 1
1.2 Related documents 1
1.3 ETSI secretariat 1
1.4 Definitions 1

2 AT commands features 2
2.1 Wavecom line settings 2
2.2 Command line 2
2.3 Information responses and result codes 2

3 General behaviors 3
3.1 SIM Insertion, SIM Removal 3
3.2 Background initialization 3

4 General commands 4
4.1 Manufacturer identification +CGMI 4
4.2 Request model identification +CGMM 4
4.3 Request revision identification +CGMR 4
4.4 Product Serial Number +CGSN 5
4.5 Select TE character set +CSCS 5
4.6 Wavecom Phonebook Character Set +WPCS 6
4.7 Request IMSI +CIMI 6
4.8 Card Identification +CCID 7
4.9 Capabilities list +GCAP 7
4.10 Repeat last command A/ 7
4.11 Power off +CPOF 8
4.12 Set phone functionality +CFUN 8
4.13 Phone activity status +CPAS 9
4.14 Report Mobile Equipment errors +CMEE 10
4.15 Keypad control +CKPD 10
4.16 Clock Management +CCLK 11
4.17 Alarm Management +CALA 11
4.18 Ring Melody Playback +CRMP 12
4.19 Ringer Sound Level +CRSL 13
5 Call Control commands 14
5.1 Dial command D 14
5.2 Hang-Up command H 16
5.3 Answer a call A 16
5.4 Remote disconnection 16
5.5 Extended error report +CEER 17
5.6 DTMF signals +VTD, +VTS 17
5.7 Redial last telephone number ATDL 18
5.8 Automatic dialing with DTR AT%Dn 18
5.9 Automatic answer ATS0 19
5.10 Incoming Call Bearer +CICB 20
5.11 Single Numbering Scheme +CSNS 20
5.12 Gain control +VGR, +VGT 21
5.13 Microphone Mute Control +CMUT 22
5.14 Speaker & Microphone selection +SPEAKER 23
5.15 Echo Cancellation +ECHO 24
5.16 SideTone modification +SIDET 27
5.17 Initialize Voice Parameters +VIP 27

6 Network service commands 29


6.1 Signal Quality +CSQ 29
6.2 Operator selection +COPS 29
6.3 Network registration +CREG 32
6.4 Read operator name +WOPN 33
6.5 Preferred operator list +CPOL 33

7 Security commands 35
7.1 Enter PIN +CPIN 35
7.2 Enter PIN2 +CPIN2 37
7.3 PIN remaining attempt number +CPINC 38
7.4 Facility lock +CLCK 39
7.5 Change password +CPWD 41

8 Phonebook commands 42
8.1 Select phonebook memory storage +CPBS 42
8.2 Read phonebook entries +CPBR 43
8.3 Find phonebook entries +CPBF 44
8.4 Write phonebook entry +CPBW 45
8.5 Phonebook phone search +CPBP 47
8.6 Move action in phonebook +CPBN 48
8.7 Subscriber number +CNUM 50
8.8 Avoid phonebook init +WAIP 51
8.9 Delete Calls Phonebook +WDCP 52
8.10 Set Voice Mail Number +CSVM 52

9 Short Messages commands 54


9.1 Parameters definition 54
9.2 Select message service +CSMS 55
9.3 New Message Acknowledgement +CNMA 56
9.4 Preferred Message Storage +CPMS 58
9.5 Preferred Message Format +CMGF 59
9.6 Save Settings +CSAS 60
9.7 Restore settings +CRES 60
9.8 Show text mode parameters +CSDH 61
9.9 New message indication +CNMI 61
9.10 Read message +CMGR 63
9.11 List message +CMGL 65
9.12 Send message +CMGS 66
9.13 Write Message to Memory +CMGW 67
9.14 Send Message From Storage +CMSS 68
9.15 Set Text Mode Parameters +CSMP 68
9.16 Delete message +CMGD 70
9.17 Service center address +CSCA 71
9.18 Select Cell Broadcast Message Types +CSCB 72
9.19 Cell Broadcast Message Identifiers +WCBM 73
9.20 Message status modification +WMSC 73
9.21 Message overwriting +WMGO 74
9.22 Unchange SMS Status +WUSS 74

10 Supplementary Services commands 75


10.1 Call forwarding +CCFC 75
10.2 Call barring +CLCK 76
10.3 Modify SS password +CPWD 77
10.4 Call waiting +CCWA 78
10.5 Calling line identification restriction +CLIR 79
10.6 Calling line identification presentation +CLIP 80
10.7 Connected line identification presentation +COLP 80
10.8 Advice of charge +CAOC 82
10.9 Accumulated call meter +CACM 83
10.10 Accumulated call meter maximum +CAMM 84
10.11 Price per unit and currency table +CPUC 84
10.12 Call related supplementary services +CHLD 85
10.13 List current calls +CLCC 86
10.14 Supplementary service notifications +CSSN 87
10.15 Unstructured supplementary service data +CUSD 88
10.16 Closed user group +CCUG 89

11 Data commands 90
11.1 Using AT Commands during a data connection 90
11.2 Bearer type selection +CBST 91
11.3 Select mode +FCLASS 93
11.4 Service reporting control +CR 94
11.5 Cellular result codes +CRC 94
11.6 DTE-DCE local rate reporting +ILRR 95
11.7 Radio link protocol parameters +CRLP 95
11.8 Others radio link parameters +DOPT 96
11.9 Select data compression %C 97
11.10 V42 bis data compression +DS 98
11.11 V42 bis data compression report +DR 99
11.12 Select data error correcting mode \N 100

12 Fax commands 101


12.1 Transmit speed +FTM 101
12.2 Receive speed +FRM 102
12.3 HDLC transmit speed +FTH 102
12.4 HDLC receive speed +FRH 102
12.5 Stop transmission and wait +FTS 103
12.6 Receive silence +FRS 103
12.7 Setting up the PC fax application: 104

13 Fax class 2 commands 105


13.1 Transmit Data +FDT 105
13.2 Receive Data +FDR 105
13.3 Transmit page ponctuation +FET 105
13.4 Page transfer status parameters +FPTS 106
13.5 Terminate Session +FK 106
13.6 Page transfer bit order +FBOR 106
13.7 Buffer size report +FBUF 107
13.8 Copy quality checking +FCQ 107
13.9 Capability to receive +FCR 107
13.10 Current sessions parameters +FDIS 108
13.11 DCE capabilities parameters +FDCC 110
13.12 Local ID string +FLID 110
13.13 Page transfer timeout parameter +FPHCTO 111
13.14 Fax Class 2 indication messages 111
14 V24-V25 commands 112
14.1 Fixed DTE rate +IPR 112
14.2 DTE-DCE character framing +ICF 113
14.3 DTE-DCE local flow control +IFC 114
14.4 Set DCD signal &C 115
14.5 Set DTR signal &D 115
14.6 Set DSR signal &S 116
14.7 Back to online mode O 116
14.8 Result code suppression Q 116
14.9 DCE response format V 117
14.10 Default configuration Z 117
14.11 Save configuration &W 118
14.12 Auto-tests &T 118
14.13 Echo E 119
14.14 Restore factory settings &F 119
14.15 Display configuration &V 119
14.16 Request identification information I 120
14.17 Data / Commands Multiplexing +WMUX 121

15 Specific AT commands 122


15.1 Cell environment description +CCED 122
15.2 Automatic RxLev indication +CCED 123
15.3 General Indications +WIND 124
15.4 Analog digital converters measurements +ADC 126
15.5 Mobile Equipment event reporting +CMER 127
15.6 Read Language Preference +WLPR 127
15.7 Write Language Preference +WLPW 128
15.8 Read GPIO value +WIOR 128
15.9 Write GPIO value +WIOW 129
15.10 Input/Output Management +WIOM 129
15.11 Abort command +WAC 131
15.12 Play tone +WTONE 131
15.13 Play DTMF tone +WDTMF 133
15.14 Wavecom Downloading +WDWL 134
15.15 Wavecom Voice Rate +WVR 135
15.16 Data Rate +WDR 136
15.17 Hardware Version +WHWV 137
15.18 Date of Production +WDOP 137
15.19 Wavecom Select Voice Gain +WSVG 138
15.20 Wavecom Status Request +WSTR 139
15.21 Wavecom Scan +WSCAN 139
15.22 Wavecom Ring Indicator Mode +WRIM 140
15.23 Wavecom 32kHz Power down Mode +W32K 141
15.24 Wavecom Change Default Melody +WCDM 141
15.25 Wavecom Software version +WSSW 142
15.26 Wavecom Custom Character Set +WCCS 143
15.27 Wavecom LoCK +WLCK 144
15.28 CPHS command +CPHS 145
15.29 Unsolicited result : Wavecom Voice Mail Indicator +WVMI 146
15.30 Wavecom Battery Charge Management +WBCM 148
15.31 Features Management +WFM 151
15.32 Commercial Features Management +WCFM 153
15.33 Wavecom Customer storage mirror +WMIR 154
15.34 Wavecom Change Default Player +WCDP 154
15.35 Wavecom CPHS Mail Box Number +WMBN 154
15.36 Wavecom Open AT control command +WOPEN 156
15.37 Wavecom Reset +WRST 158
15.38 Set Standard Tone +WSST 159
15.39 Wavecom Location +WLOC 160
15.40 Wavecom Bus Read +WBR 163
15.41 Wavecom Bus Write +WBW 164
15.42 Wavecom Bus Management +WBM 166
15.43 Wavecom Hang-up +WATH 168

16 SIM TOOLKIT 169


16.1 Overview of SIM Application ToolKit 169
16.2 Messages exchanged during a SIM ToolKit operation. 171
16.3 SIM ToolKit commands 172

17 Other AT commands 186


17.1 V.25 ter recommendation 186
17.2 GSM 07.05 recommendation 186
17.3 GSM 07.07 recommendation 186

18 Appendices 187
18.1 ME error result code : +CME ERROR: <error> 187
18.2 Message service failure result code: +CMS ERROR : <er> 187
18.3 Specific error result codes 188
18.4 Failure Cause from GSM 04.08 recommendation (+CEER) 189
18.5 Specific Failure Cause for +CEER 191
18.6 GSM 04.11 Annex E-2: Mobile originating SM-transfer 191
18.7 Unsolicited result codes 193
18.8 Final result codes 194
18.9 Intermediate result codes 194
18.10 Parameters storage 195
18.11 GSM sequences list 199
18.12 Operator names 202
18.13 Data / Commands multiplexing protocol 212
19 APPENDIX A (informative) 215
19.1 Examples with the PIN required 215
19.2 Examples about phonebooks 218
19.3 Examples about short messages 220
19.4 Examples about Fax class 2 221

20 APPENDIX B: Support of SIM


ToolKit by The M.E. 223

21 APPENDIX C: Structure of
TERMINAL PROFILE 225

22 APPENDIX D: Command Type


and Next Action Indicator. 228

23 APPENDIX E: Coding of
Alpha fields in the SIM for UCS2 229

24 APPENDIX F:
Specification of Power
Down Control via RS232 231

25 APPENDIX G:
Conditions for command
execution and dependence to SIM 233
25.1 General commands 233
25.2 Call Control commands 233
25.3 Network service commands 234
25.4 Security commands 234
25.5 Phonebook commands 234
25.6 Short Messages commands 235
25.7 Supplementary Services commands 235
25.8 Data commands 236
25.9 Fax commands 236
25.10 Class 2 commands 236
25.11 V24-V25 commands 237
25.12 Specific AT commands 237
25.13 SIM Toolkit commands 238
WAVECOM, WISMO are trademarks or registered trademarks of Wavecom S.A. All other company and/or
product names mentioned may be trademarks or registered trademarks of their respective owners.
1 Introduction

1.1 Scope of this document


This document describes the AT-command based messages exchanged between an
application and the WAVECOM products in order to manage GSM related events or
services.

1.2 Related documents


This interface specification is based on the following recommendations:
➊ ETSI GSM 07.05: Digital cellular telecommunications system (Phase 2);
Use of DTE-DCE interface for Short Message Service (SMS) and Cell Broadcast Service
(CBS)
➋ ETSI GSM 07.07: Digital cellular telecommunications system (Phase 2);
AT command set for GSM Mobile Equipment (ME)
➌ ITU-T Recommendation V.25 ter: Serial asynchronous automatic dialling and control
➍ ETSI GSM 03.40: Digital cellular telecommunications system (Phase 2);
Technical implementation of the Short Message Service (SMS) Point-to-Point (PP)
➎ ETSI GSM 03.38: Digital cellular telecommunications system (Phase 2);
Alphabets and language-specific information
➏ ETSI GSM 04.80: Digital cellular telecommunications system (Phase 2):
Mobile radio interface layer 3, Supplementary service specification, Formats and coding

1.3 ETSI secretariat


The following addresses may be of use in obtaining the latest GSM recommendations:
Postal address: F-06921 Sophia Antipolis CEDEX – France
Office address: 650 Route des Lucioles – Sophia Antipolis – Valbonne – France
e-mail: secretariat@etsi.fr
Tel: +33 4 92 94 42 00
Fax:+33 4 93 65 47 16

1.4 Definitions
The words, “Mobile Station” (MS) or “Mobile Equipment” (ME) are used for mobile
terminals supporting GSM services.

A call from a GSM mobile station to the PSTN is called a “mobile originated call” (MOC) or
“outgoing call”, and a call from a fixed network to a GSM mobile station is called a
“mobile terminated call” (MTC) or “incoming call”.

In this document, the word “product” refers to any Wavecom product supporting the AT
commands interface.

1
2 AT commands features

2.1 Wavecom line settings


A serial link handler is set with the following default values (factory settings):
autobaud, 8 bits data, 1 stop bit, no parity, RTS/CTS flow control.
Please use the +IPR, +IFC and +ICF commands to change these settings.

2.2 Command line


Commands always start with AT (which means ATtention) and finish with a <CR>
character.

2.3 Information responses and result codes


Responses start and end with <CR><LF>, except for the ATV0 DCE response format) and
the ATQ1 (result code suppression) commands.
❑ If command syntax is incorrect, an ERROR string is returned.
❑ If command syntax is correct but with some incorrect parameters,
the +CME ERROR: <Err> or +CMS ERROR: <SmsErr> strings are returned with
different error codes.
❑ If the command line has been performed successfully, an OK string is returned.
In some cases, such as “AT+CPIN?” or (unsolicited) incoming events, the product does not
return the OK string as a response.
In the following examples <CR> and <CR><LF> are intentionally omitted.

2
3 General behaviors

3.1 SIM Insertion, SIM Removal


SIM card Insertion and Removal procedures are supported. There are software functions
relying on positive reading of the hardware SIM detect pin. This pin state (open/closed) is
permanently monitored.
When the SIM detect pin indicates that a card is present in the SIM connector, the product
tries to set up a logical SIM session. The logical SIM session will be set up or not
depending on whether the detected card is a SIM Card or not. The AT+CPIN? command
delivers the following responses:

❑ If the SIM detect pin indicates “absent”, the response to AT+CPIN? is “+CME
ERROR 10” (SIM not inserted).
❑ If the SIM detect pin indicates “present”, and the inserted Card is a SIM Card, the
res-ponse to AT+CPIN? is “+CPIN: xxx” depending on SIM PIN state.
❑ If the SIM detect pin indicates “present”, and the inserted Card is not a SIM Card,
the response to AT+CPIN? is CME ERROR 10.
❑ These last two states are not given immediately due to background initialization.
Between the hardware SIM detect pin indicating “present” and the previous
results the AT+CPIN? sends “+CME ERROR: 515” (Please wait, init in progress).

When the SIM detect pin indicates card absence, and if a SIM Card was previously
inserted, an IMSI detach procedure is performed, all user data is removed from the
product (Phonebooks, SMS etc.). The product then switches to emergency mode.

3.2 Background initialization


After entering the PIN (Personal Identification Number), some SIM user data files are
loaded into the product (Phonebooks, SMS status, etc.). Please be aware that it might take
some time to read a large phonebook.
The AT+CPIN? command response comes just after the PIN is checked. After this response
user data is loaded (in background). This means that some data may not be available just
after PIN entry is confirmed by ’OK’. The reading of phonebooks will then be refused by
“+CME ERROR: 515” or “+CMS ERROR: 515” meaning, “Please wait, service is not
available, init in progress”.

This type of answer may be sent by the product at several points:


❑ when trying to execute another AT command before the previous one is
completed (before response),
❑ when switching from ADN to FDN (or FDN to ADN) and trying to read the relevant
phonebook immediately,
❑ when asking for +CPIN? status immediately after SIM insertion and before the
product has determined if the inserted card is a valid SIM Card.

3
4 General commands

4.1 Manufacturer identification +CGMI

4.1.1 Description:
This command gives the manufacturer identification.

4.1.2 Syntax:
Command Syntax: AT+CGMI
COMMAND POSSIBLE RESPONSES
AT+CGMI WAVECOM MODEM
OK
Note: Get manufacturer identification Note: Command valid, Wavecom modem

4.2 Request model identification +CGMM

4.2.1 Description:
This command is used to get the supported frequency bands. With multi-band products
the response may be a combination of different bands.

4.2.2 Syntax:
Command Syntax: AT+CGMM
COMMAND POSSIBLE RESPONSES
AT+CGMM 900P
OK
Note: Get hardware version Note: GSM 900 MHz primary band. Other possible answers: “900E”
(extended band), “1800” (DCS), “1900” (PCS) or “MULTIBAND”

4.3 Request revision identification +CGMR

4.3.1 Description:
This command is used to get the revised software version.

4.3.2 Syntax:
Command Syntax: AT+CGMR
COMMAND POSSIBLE RESPONSES
AT+CGMR 310_G250.51 806216 032199 17:04
OK
Note: Get software version Note: Software release 3.10, revision 51 generated on the
21st of March 1999

4
4.4 Product Serial Number +CGSN

4.4.1 Description:
This command allows the user application to get the IMEI (International Mobile Equipment
Identity) of the product.

4.4.2 Syntax:
Command Syntax: AT+CGSN
COMMAND POSSIBLE RESPONSES
AT+CGSN 135790248939
OK
Note: Get the IMEI Note: IMEI read from EEPROM
AT+CGSN +CME ERROR: 22
Note: Get the IMEI Note: IMEI not found in EEPROM

4.5 Select TE character set +CSCS

4.5.1 Description:
This command informs the ME which character set is used by the TE. The ME can convert
each character of entered or displayed strings. This is used to send, read or write short
messages. See also +WPCS for the phonebooks’ character sets.

4.5.2 Syntax:
Command Syntax: AT+CSCS=<Character Set>
COMMAND POSSIBLE RESPONSES
AT+CSCS=”GSM” OK
Note: GSM default alphabet Note: Command valid
AT+CSCS=”PCCP437” OK
Note: PC character set code page 437 Note: Command valid
AT+CSCS=? +CSCS: ("GSM","PCCP437","CUSTOM","HEX")
OK
Note: Get possible values Note: Possible values

4.5.3 Defined values:


<Character Set>
“GSM”................................................GSM default alphabet.
“PCCP437”.......................................PC character set code page 437.
“CUSTOM” .....................................User defined character set (cf. +WCCS command).
“HEX” .................................................Hexadecimal mode. No character set used ; the user can read
or write hexadecimal values.

5
4.6 Wavecom Phonebook Character Set +WPCS

4.6.1 Description:
This specific command informs the ME which character set is used by the TE for the
phonebooks. The ME can convert each character of entered or displayed strings. This is
used to read or write phonebook entries. See also +CSCS for the short messages character
sets.

4.6.2 Syntax:
Command Syntax: AT+WPCS=<Character Set>
COMMAND POSSIBLE RESPONSES
AT+WPCS=”TRANSPARENT” OK
Note: Transparent mode Note: Command valid
AT+WPCS=”CUSTOM” OK
Note: Custom character set Note: Command valid
AT+WPCS=? +WPCS: ("TRANSPARENT","HEX","CUSTOM")
OK
Note: Get possible values Note: Possible values

4.6.3 Defined values:


<Character Set>
“TRANSPARENT” .......................Transparent mode. The strings are displayed and entered as
they are stored in SIM or in ME.
“CUSTOM” .....................................User defined character set (cf. +WCCS command).
“HEX” .................................................Hexadecimal mode. No character set used ; the user can read
or write hexadecimal values.

4.7 Request IMSI +CIMI

4.7.1 Description:
This command is used to read and identify the IMSI (International Mobile Subscriber
Identity) of the SIM card. The PIN may need to be entered before reading the IMSI.

4.7.2 Syntax:
Command Syntax: AT+CIMI
COMMAND POSSIBLE RESPONSES
AT+CIMI 208200120320598
Note: Read the IMSI Note: IMSI value (15 digits), starting with MCC
(3 digits) / MNC (2 digits, 3 for PCS 1900)
See appendix 18.12 for MCC / MNC description.

6
4.8 Card Identification +CCID

4.8.1 Description:
This command orders the product to read the EF-CCID file on the SIM card.

4.8.2 Syntax:
Command Syntax: AT+CCID
COMMAND POSSIBLE RESPONSES
AT+CCID +CCID: “123456789AB111213141”
Note: Get card ID Note: EF-CCID is present, hexadecimal format
AT+CCID? + CCID: “123456789AB111213141”
Note: Get current value Note: Same result as +CCID
AT+CCID? OK
Note: Get possible values Note: No parameter but this command is valid

If there is no EF-CCID file present on the SIM, the +CCID answer will not be sent, but the
OK message will be returned.

4.9 Capabilities list +GCAP

4.9.1 Description:
This command gets the complete list of capabilities.

4.9.2 Syntax:
Command Syntax: AT+GCAP
COMMAND POSSIBLE RESPONSES
AT+GCAP +GCAP: +CGSM +FCLASS
OK
Note: Get capabilities list Note: Supports GSM and FAX commands

4.10 Repeat last command A/

4.10.1 Description:
This command repeats the previous command. Only the A/ command itself cannot be
repeated.

4.10.2 Syntax:
Command Syntax: A/
COMMAND POSSIBLE RESPONSES
A/
Note: Repeat last command

7
4.11 Power off +CPOF

4.11.1 Description:
This specific command stops the GSM software stack as well as the hardware layer. The
AT+CFUN=0 command is equivalent to +CPOF.

4.11.2 Syntax:
Command Syntax: AT+CPOF
COMMAND POSSIBLE RESPONSES
AT+CPOF OK
Note: Stop GSM stack Note: Command valid

4.12 Set phone functionality +CFUN

4.12.1 Description:
This command selects the mobile station’s level of functionality.
When the application wants to stop the product with a power off, or if the application
wants to force the product to execute an IMSI DETACH procedure, then it must send:
AT+CFUN=0 (equivalent to AT+CPOF)
This command executes an IMSI DETACH and makes a backup copy of some internal
parameters in SIM and in EEPROM. The SIM card cannot then be accessed.
If the mobile equipment is not powered off by the application after this command has
been sent, a re-start command (AT+CFUN=1) will have to issued to restart the whole GSM
registration process.
If the mobile equipment is turned off after this command, then a power on will
automatically restart the whole GSM process.

The AT+CFUN=1 command restarts the entire GSM stack and GSM functionality: a
complete software reset is performed. All parameters are reset to their previous values if
AT&W was not used.
If you write entries in the phonebook (+CPBW) and then reset the product directly
(AT+CFUN=1, with no previous AT+CFUN=0 command), some entries may not be written
(the SIM task does not have enough time to write entries in the SIM card).
In addition, the OK response will be sent at the last baud rate defined by the +IPR
command. With the autobauding mode the response can be at a different baud rate, it is
therefore preferable to save the defined baud rate with AT&W before directly sending the
AT+CFUN=1 command.

8
4.12.2 Syntax:
Command Syntax: AT+CFUN=<functionality level>
COMMAND POSSIBLE RESPONSES
AT+CFUN? +CFUN: 1
OK
Note: Ask for current functionality level Note: Full functionality
AT+CFUN=0 OK
Note: Set minimum functionality, IMSI detach procedure Note: Command valid
AT+CFUN=1 OK
Note: Set the full functionality mode with a Note: Possible values
complete software reset

4.13 Phone activity status +CPAS

4.13.1 Description:
This command returns the activity status of the mobile equipment.

4.13.2 Syntax:
Command Syntax: AT+CPAS
COMMAND POSSIBLE RESPONSES
AT+CPAS +CPAS: <pas>
Note: Current activity status OK

4.13.3 Defined values:


<pas>
0: ready (allow commands from TA/TE)
1: unavailable (does not allow commands)
2: unknown
3: ringing (ringer is active)
4: call in progress
5: asleep (low functionality)

9
4.14 Report Mobile Equipment errors +CMEE

4.14.1 Description:
This command disables or enables the use of the “+CME ERROR : <xxx>” or “+CMS
ERROR :<xxx>” result code instead of simply “ERROR”. See appendix 18.1 for +CME
ERROR result codes description and appendix 0 for +CMS ERROR result codes.

4.14.2 Syntax:
Command Syntax: AT+CMEE=<error reporting flag>
COMMAND POSSIBLE RESPONSES
AT+CMEE=0 OK
Note: Disable ME error reports, use only « ERROR »
AT+CMEE=1 OK
Note: Enable «+CME ERROR: <xxx>» or
«+CMS ERROR: <xxx>»

4.15 Keypad control +CKPD

4.15.1 Description:
This command emulates the ME keypad by sending each keystroke as a character in a
<keys> string.
The supported GSM sequences are listed in the appendix.
If emulation fails, a +CME ERROR: <err> is returned.
If emulation succeeds, the result depends on the GSM sequence activated: <keys>: string
of the following characters (0-9,*,#).
NOTE: In the case where the FDN phonebook is activated, the sequences concerning “call forwarding”
are allowed only if the entire sequence is written in the FDN.

4.15.2 Syntax:
Command Syntax: AT+CKPD=<keys>
COMMAND POSSIBLE RESPONSES
AT+CKPD=”*#21#” +CCFC: 0,7
Note: Check every call forwarding status
AT+CKPD=”1234” +CME ERROR 3
Note: Sequence not allowed

10
4.16 Clock Management +CCLK

4.16.1 Description:
This command is used to set or get the current date and time of the ME real-time clock.
String format for date/time is: “yy/MM/dd,hh:mm:ss”.
Valid years are 98 (for 1998) to 97 (for 2097). The seconds field is not mandatory.
Default date/time is “98/01/01,00:00:00” (January 1st, 1998 / midnight).

4.16.2 Syntax:
Command Syntax: AT+CCLK=<date and time string>
COMMAND POSSIBLE RESPONSES
AT+CCLK=”00/06/09,17:33:00” OK
Note: set date to June 9th, 2000, and time to 5:33pm Note: Date/Time stored
AT+CCLK=”00/13/13,12:00:00” +CME ERROR 3
Note: Incorrect month entered
AT+CCLK? +CCLK: “00/06/09,17:34:23”
Note: Get current date and time Note: current date is June 9th, 2000 current time is 5:34:23 pm

4.17 Alarm Management +CALA

4.17.1 Description:
This command is used to set alarms date/time in the ME.
String format for alarms : “yy/MM/dd,hh:mm:ss” (see +CCLK).
The maximum number of alarms is 16. Seconds are not taken into account.

4.17.2 Syntax:
Command Syntax: AT+CALA=<date and time string> (set alarm)
AT+CALA=””,<index> (delete alarm)
COMMAND POSSIBLE RESPONSES
AT+CALA=”00/06/09,07:30” OK
Note: set an alarm for June 9th, 2000 at 7:30 am Note: Alarm stored
AT+CALA=”99/03/05,13:00:00” +CME ERROR 3
Note: set an alarm for March 5th, 1999 at 1:00 pm Note: Invalid alarm (date/time expired)
AT+CALA? +CALA: “00/06/08,15:25:00”,0
+CALA: “00/06/09,07:30:00”,1
+CALA: “00/06/10,23:59:00”,2
Note: list all alarms Note: three alarms are set (index 0, 1, 2)
+CALA: “00/06/08,15:25:00”,0
Note: an alarm occurs (index 0)
AT+CALA=””,2 OK
Note: delete alarm index 2 Note: Alarm index 2 deleted
AT+CALA? +CALA: “00/06/09,07:30:00”,1
Note: list all alarms Note: Only one alarm (index 1)

11
4.18 Ring Melody Playback +CRMP

4.18.1 Description:
This command allows a melody to be played. All melodies are manufacturer defined.
For incoming voice, data or fax calls, 10 manufacturer-defined melodies can be played
back (in a loop).
For an incoming short message, 2 manufacturer-defined sounds can be played back
(once). Melody #1: short beep / Melody #2: long beep.
NOTE: loop melodies (for voice/data/fax call) must be stopped by a +CRMP command with the <index>
field set to 0 (example: +CRMP=0,,,0).
When the <volume> parameter is given, this overwrites the <sound level> value of the +CRSL
command. If the <volume> parameter is not given, the <sound level> value of +CRSL is used as default
value.

4.18.2 Syntax:
Command Syntax: AT+CRMP=<call type>[,<volume>,<type>,<index>]
COMMAND POSSIBLE RESPONSES
AT+CRMP=0,7,0,2 OK
Note: Play voice call melody index 2 with volume level 7 Note: Melody Playback.
AT+CRMP=0,,,0 OK
Note: Stop the melody Note: The melody is stopped.
AT+CRMP=? +CRMP: (0-3),(0-15),0,(0-10)
Note: supported parameters OK

4.18.3 Defined values:


<call type>
0: Incoming voice call
1: Incoming data call
2: Incoming fax call
3: Incoming short message (SMS)
<volume>
0: Min volume

6: Default volume
15: Max volume
<type>
0: Manufacturer Defined (default)
<index>
0 : Stop Melody Playback
1-10: Melody ID for voice/data/fax call type (default : 1)
1-2 : Melody ID for short message (default : 1)

12
4.19 Ringer Sound Level +CRSL

4.19.1 Description:
This command is used to set/get the sound level of the ringer on incoming calls. The set
command changes the default <volume> value of the +CRMP command.

4.19.2 Syntax:
Command Syntax: AT+CRSL=<sound level>
COMMAND POSSIBLE RESPONSES
AT+CRSL=0 OK
Note: Set volume to Min. Note: Current ring playing with Min. volume.
AT+CRSL=15 OK
Note: Set volume to Max. Note: Current ring playing with Max. volume.
AT+CRSL? +CRSL: 15
OK
Note: get current ringer sound level Note: Current level is 15 (max.)
AT+CRSL=? +CRSL: (0-15)
Note: supported parameters OK

4.19.3 Defined values:


<sound level>
0: Min volume
6: Default volume (default)
15: Max volume

13
5 Call Control commands

5.1 Dial command D

5.1.1 Description:
The ATD command is used to set a voice, data or fax call. As per GSM 02.30, the dial
command also controls supplementary services.
For a data or a fax call, the application sends the following ASCII string to the product (the
bearer must be previously selected with the +CBST command):
ATD<nb> where <nb> is the destination phone number.

For a voice call, the application sends the following ASCII string to the product: (the bearer
may be selected previously, if not a default bearer is used).
ATD<nb>; where <nb> is the destination phone number.

Please note that for an international number, the local international prefix does not need
to be set (usually 00) but does need to be replaced by the ‘+’ character.
Example: to set up a voice call to Wavecom offices from another country, the AT command
is: “ATD+33146290800;”
Note that some countries may have specific numbering rules for their GSM handset
numbering.
The response to the ATD command is one of the following:

Numeric code
Verbose result code Description
with ATV0 set
OK 0 if the call succeeds, for voice call only
CONNECT <speed> 10,11,12, if the call succeeds, for data calls only,
13,14,15 <speed> takes the value negotiated
by the product.
BUSY 7 If the called party is already
in communication
NO ANSWER 8 If no hang up is detected after a fixed
network time-out
NO CARRIER 3 Call setup failed or remote user
release. Use the AT+CEER command
to know the failure cause

Direct dialling from a phonebook (stored in the SIM card) can be performed with the
following command:
ATD> <index>; to call <index> from the selected phonebook (by the +CPBS command)
ATD> “BILL”; to call “BILL” from the selected phonebook
ATD> mem <index> (mem is “SM","LD","MC","ME","RC","MT" or "SN",
see +CPBS command) allows direct dialling from a phonebook number. Does not function
with "ON" mem.

14
5.1.2 Syntax:
Command Syntax: ATD<nb>[<I>][;]
ATD>[<mem>]<index>[<I>][;]
ATD>[<mem>]<name>[<I>][;]
COMMAND POSSIBLE RESPONSES
AT+CPBS? +CPBS:”SM”,8,10
Note: Which phonebook is selected ? Note: ADN phonebook is selected, 8 locations are used and
10 locations are available
ATD>SM6; OK
Note: Call index 6 from AND phonebook Note: Call succeeds

When the FDN phonebook has been locked, only numbers beginning with the digits of
FDN phonebook entries can be called.
For example, if “014629” is entered in the FDN phonebook all the phone numbers
beginning with these 6 digits can be called.
The CLIR supplementary service subscription can be overridden for this call only.
“I” means “invocation” (restrict CLI presentation).
“i” means “suppression” (allow CLI presentation).
Control of CUG supplementary service information by “G” or “g” is allowed for this call
only. The index and info values set with the +CCUG command are used.
An outgoing call attempt could be refused if the AOC service is active and credit has
expired (NO CARRIER).
When trying to set up an outgoing call while there is an active call, the active call is first
put on hold, then the call set up is carried out.
As per GSM 02.30, GSM sequences may be controlled using dial commands. These
sequences can contain “*”, “#”, but “;” is forbidden.
If the sequence is not supported or fails, +CME ERROR: <err> is returned.
In the case where the FDN phonebook is activated, the sequences concerning call
forwarding are allowed only if there are written in the FDN.

See paragraph 18.11 to have the list of supported sequences.

COMMAND POSSIBLE RESPONSES


ATD*#21# +CCFC: 0,7
Note: Check any call forwarding status Note: No call forwarding
ATD**61*+33146290800**25# OK
Note: Register call forwarding on no reply, Note: done
with no reply timer fixed at 25 s.
ATD*2# +CME ERROR 3
Note: Bad sequence

15
5.2 Hang-Up command H

5.2.1 Description:
The ATH (or ATH0) command is used by the application to disconnect the remote user. In
the case of multiple calls, all calls are released (active, on-hold and waiting calls).
The specific Wavecom ATH1 command has been appended to disconnect the current
outgoing call, only in dialing or alerting state (ie. ATH1 can be used only after the ATD
command, and before its terminal response (OK, NO CARRIER, ...). It can be useful in the
case of multiple calls.

5.2.2 Syntax:
Command Syntax: ATH
COMMAND POSSIBLE RESPONSES
ATH OK
Note: Ask for disconnection Note: Every call, if any, are released
ATH1 OK
Note: Ask for outgoing call disconnection Note: Outgoing call, if any, is released

5.3 Answer a call A

5.3.1 Description:
When the product receives a call, it sets the RingInd signal and sends the ASCII “RING” or
“+CRING: <type>” string to the application (+CRING if the cellular result code +CRC is
enabled). Then it waits for the application to accept the call with the ATA command.

5.3.2 Syntax:
Command Syntax: ATA
COMMAND POSSIBLE RESPONSES
RING
Note: Incoming call
ATA OK
Note: Answer to this incoming call Note: Call accepted
ATH OK
Note: Disconnect call OK Note: Call disconnected

5.4 Remote disconnection

This message is used by the product to inform the application that an active call has been
released by the remote user.
The product sends “NO CARRIER” to the application and sets the DCD signal.
In addition, for AOC, the product can release the call if credit has expired (release cause 68
with +CEER command).

16
5.5 Extended error report +CEER

5.5.1 Description:
This command gives the cause of call release when the last call set up (originating or
answering) failed.

5.5.2 Syntax:
Command Syntax: AT+CEER
COMMAND POSSIBLE RESPONSES
ATD123456789; NO CARRIER
Note: Outgoing voice call Note: Call setup failure
AT+CEER +CEER : Error <xxx>
OK
Note: Ask for reason of release Note: <xxx> is the cause information element values from
GSM recommendation 04.08 or specific Call accepted

For the cause information element from GSM 04.08 see chapter 18.4 or 18.5.
“NO CARRIER” indicates that the AT+CEER information is available for failure diagnosis.

5.6 DTMF signals +VTD, +VTS

5.6.1 +VTD Description:


The product enables the user application to send DTMF tones over the GSM network. This
command is used to define tone duration (the default value is 300ms).
To define this duration, the application uses:
AT+VTD=<n> where <n>*100 gives the duration in ms.
If n < 4, tone duration is 300 ms.

5.6.2 +VTD Syntax:


Command Syntax: AT+VTD=<n>
COMMAND POSSIBLE RESPONSES
AT+VTD=6 OK
Note: To define 600 ms tone duration Note: Command valid
AT+VTD=0 OK
Note: To set the default value

5.6.3 +VTS Description:


The product enables the user application to send DTMF tones over the GSM network. This
command enables tones to be transmitted.
To transmit DTMF tones (only when there is an active call), the application uses:
AT+VTS=<Tone> where <Tone> is in {0-9,*,#,A,B,C,D}

17
5.6.4 +VTS Syntax:
Command Syntax: AT+VTS=<Tone>
COMMAND POSSIBLE RESPONSES
AT+VTS=A OK
Note: Command valid
AT+VTS=11 +CME ERROR: 4
Note: To set the default value Note: If the <Tone> is wrong
AT+VTS=4 +CME ERROR: 3
Note: If there is no communication

5.6.5 Informative example:


To send tone sequence 13#, the application sends :
AT+VTS=1;+VTS=3;+VTS=#
OK

5.7 Redial last telephone number ATDL

5.7.1 Description:
This command is used by the application to redial the last number used in the ATD
command. The last number dialled is displayed followed by “;” for voice calls only

5.7.2 Syntax:
Command Syntax: ATDL
COMMAND POSSIBLE RESPONSES
ATDL 0146290800;
OK
Note: Redial last number Note: Last call was a voice call. Command valid

5.8 Automatic dialing with DTR AT%Dn

5.8.1 Description:
This command enables and disables:
❑ automatic dialling of the phone number stored in the first location of the ADN
phonebook,
❑ automatic sending of the short message (SMS) stored in the first location
of the SIM.
The number is dialled when DTR OFF switches ON.
The short message is sent when DTR OFF switches ON.

18
5.8.2 Syntax:
Command Syntax: AT%D<n>[ ;]
COMMAND POSSIBLE RESPONSES
AT%D1; OK
Note: Activates DTR number dialling Note: Command has been executed
DTR is OFF
DTR switches ON
Note: The number in the first location of the ADN
is dialled automatically
DTR switches OFF
Note: The product goes on-hook
AT%D2 OK
Note: Activates DTR short message sending Note: Command has been executed

5.8.3 Defined values:


<n> (0-2)
to enable or disable automatic message transmission or number dialling.
Informs the product that the number is a voice rather than a fax or data number.
AT%D0
Disables automatic DTR number dialling / message transmission.
AT%D1;
Enables automatic DTR dialling if DTR switches from OFF to ON; Dials the phone number
in the first location of the ADN phonebook. Voice call.
AT%D1
Activates automatic DTR dialling if DTR switches from OFF to ON; Dials the phone number
in the first location of the ADN phonebook. Data or Fax call.
AT%D2
Activates automatic DTR short message transmission if DTR switches from OFF to ON.

5.9 Automatic answer ATS0

5.9.1 Description:
This S0 parameter determines and controls the product automatic answering mode.

5.9.2 Syntax:
Command Syntax: ATS0=<value>
COMMAND POSSIBLE RESPONSES
ATS0=2 OK
Note: Automatic answer after 2 rings
ATS0? 002
OK
Note: Current value Note: always 3 characters padded with zeros
ATS0=0 OK
Note: No automatic answer Note: Command valid
All others S-parameters (S6,S7,S8 …) are not implemented.

19
5.10 Incoming Call Bearer +CICB

5.10.1 Description:
This specific command is used to set the type of incoming calls when no incoming bearer
is given (see +CSNS).
NOTE: setting the +CICB command affects the current value of +CSNS.

5.10.2 Syntax:
Command Syntax: AT+CICB=<mode>
COMMAND POSSIBLE RESPONSES
AT+CICB=1 OK
Note: If no incoming bearer, force a fax call Note: Command accepted
AT+CICB=2 OK
Note: If no incoming bearer, force a voice call Note: Command accepted
AT+CICB? +CICB: 2
Note: Interrogate value Note: Default incoming bearer: voice call
AT+CICB=? +CICB: (0-2)
Note: Test command Note: Speech, data or fax default incoming bearer

5.10.3 Defined values:


<mode>
0: Data
1: Fax
2: Speech

5.11 Single Numbering Scheme +CSNS

5.11.1 Description:
This command selects the bearer to be used when an MT single numbering scheme call is
set up (see +CICB).
NOTE: setting the +CSNS command affects the current value of +CICB.

5.11.2 Syntax:
Command Syntax: AT+CSNS
COMMAND POSSIBLE RESPONSES
AT+CSNS=2 OK
Note: force a fax call Note: Command accepted
AT+CSNS=0 OK
Note: force a voice call Note: Command accepted
AT+CSNS? +CSNS: 0
Note: Interrogate value Note: Default incoming bearer: voice call
AT+CSNS=? +CSNS: (0,2,4)
Note: Test command Note: Voice, data or fax default incoming bearer

20
5.11.3 Defined values:
<mode>
0: Voice
2: Fax
4: Data

5.12 Gain control +VGR, +VGT

5.12.1 Description:
This command is used by the application to tune the receive gain of the speaker and the
transmit gain of the microphone. The application sends:

AT+VGT=<val> for transmit gain AT+VGT=<val> for transmit gain


AT+VGR=<val> for receive gain
Controller 1 Controller 1 Controller 2 Controller 2
0 to 15 +6 db 0 to 31 +30 db 0 +0 db
16 to 31 +4 db 32 to 63 +33 db 1 +0,5 db
32 to 47 +2 db 64 to 95 +36 db 2 +1 db
48 to 63 +0 db 96 to 127 +39 db 3 +1,5 db
64 to 79 -2 db 128 to 159 +42 db … …
80 to 95 -4 db 160 to 191 +45 db 19 +9,5 db
96 to 111 -6 db 192 to 223 +48 db 20 +10 db
112 to 127 -8 db 224 to 255 +51 db 21 to 60 +30 db
128 to 143 -10 db 61 +30,5 db
144 to 159 -12 db 62 +31 db
160 to 175 -14 db … …
176 to 191 -16 db 101 +50,5 db
192 to 207 -18 db 102 to 127 +51 db
208 to 223 -20 db 128 to 243 -6,5 db
224 to 255 (*) -22 db 244 -6 db
245 -5,5 db
246 -5 db
… …
255 -0,5 db
(*) For Wismo Quik Q22xx : 224 to 239 : -22db / 240 to 255 : -24db
The gain values listed here are relative, for absolute (electrical) values please refer to the
specific hardware documentation of the module used in the application.

21
5.12.2 Syntax:
Command Syntax: AT+VGR=<Rgain>
AT+VGT=<Tgain>
COMMAND POSSIBLE RESPONSES
AT+VGR=25 OK
Note: Command valid
AT+VGT=45 OK
Note: Command valid
AT+VGR? +VGR: 64
Note: Interrogate value Note: Default receive gain
AT+VGR=? +VGR : (0-255)
Note: Test command Note: Possible values
AT+VGT? +VGT: 64
Note: Interrogate value Note: Default transmit gain
AT+VGT=? +VGT : (0-255)
Note: Test command Note: Possible values

5.13 Microphone Mute Control +CMUT

5.13.1 Description:
This command is used to mute the microphone input on the product (for the active
microphone set with the +SPEAKER command). This command is only allowed during a call.

5.13.2 Syntax:
Command Syntax: AT+CMUT=<mode>
COMMAND POSSIBLE RESPONSES
AT+CMUT=? +CMUT : (0,1)
OK
Note: Test command Note: Enable / disable mute
AT+CMUT? +CMUT : 0
OK
Note: Ask for current value Note: Current value is OFF
AT+CMUT=1 OK
Note: Mute ON (call active) Note: Command valid
AT+CMUT?+CMUT : 1 OK
Note: Ask for current value Note: Mute is active (call active)
AT+CMUT=0 +CME ERROR:3
Note: Mute OFF (call not active) Note: Command not valid

5.13.3 Defined values:


<mode>
0: microphone mute off (default value).
1: microphone mute on.

22
5.14 Speaker & Microphone selection +SPEAKER

5.14.1 Description:
This specific command is used to select the speaker and the microphone set.

5.14.2 Syntax:
Command Syntax: AT+SPEAKER=<ActiveSpkMic>
COMMAND POSSIBLE RESPONSES
AT+SPEAKER=0 OK
Note: Speaker ONE and Micro ONE Note: Command valid
AT+SPEAKER? +SPEAKER: 0
OK
Note: Speaker ONE and Micro ONE are active

5.14.3 Defined values:


<mode>
0: speaker one, micro one
1: speaker two, micro two

23
5.15 Echo Cancellation +ECHO

5.15.1 Description:
This specific command is used to enable, disable or configure the Echo Cancellation
functions for voice calls (in rooms, in cars, etc.).
It is necessary to tune the Microphone gain (AT+VGT) and the Speaker gain (AT+VGR)
before activating the Echo Cancellation.

5.15.2 Syntax:
Command Syntax: AT+ECHO= <mode> [,<AlgoId>,<Param1>,<Param2>,<Param3>,
<Param4>,<Param5>,<Param6>]
COMMAND POSSIBLE RESPONSES
AT+CMEE=1 OK
Note: Enables the use of result code
AT+SPEAKER? + SPEAKER: 0
OK
Note: Speaker ONE and Micro ONE are active
AT+SIDET=0 OK
Note: Deactivate the Sidetone
AT+SIDET? +SIDET: 0,0
AT+ECHO? +ECHO: 0,1,0,3,10,7
Note: Read current settings OK
AT+ECHO=1,1,0,3,10,7 OK
Note: Active Echo cancellation 1 for Mic/Spk one.
AT+ECHO? +ECHO: 1,1,0,3,10,7
Note: Read current settings OK
AT+ECHO=1,3,30,8000,256 +CME ERROR: 519
Note: Activate the Echo cancellation 3 Note: The new algorithm will be activated after a reset of
the product
AT+ECHO? +ECHO: 3,3,30,8000,256
Note: Read the Echo cancellation settings OK
AT+CFUN=1 OK
Note: Reset the product
AT+ECHO? +ECHO: 1,3,30,8000,256
Note: Read current settings OK
AT+ECHO=0 OK
Note: Deactivate the Echo Cancellation

24
5.15.3 Defined values:
<mode>
0: Deactivate Echo
1: Activate Echo

<AlgoId>
1: Echo cancellation 1
3: Echo cancellation 3 (optional)

Echo cancellation 1 (4 parameters):


The parameter <Volout> specifies the maximum attenuation of the switch
<Volout>
0: 31 db (default)
1: 29 db
2: 27 db
3: 25 db

14 : 3 db
15 : 1 db

The parameter <Step> specifies the attenuation step between attenuation and no
attenuation.
<Step>
0: 1 db
1: 2 db
2: 3 db
3: 4 db (default)

The <PcmThRel> parameter specifies the relative threshold between max and min energy
information.
The allowed range is [ 0 ; 31 ]. (10 by default)
The <PcmThMax> parameter specifies threshold of max energy information.
The allowed range is [ 0 ; 31 ]. (7 by default)

Echo Cancellation 3 (3 parameters):


<AlgoParam> high value leads to high echo attenuation but the full-duplex quality will be
less efficient.
The allowed range is [ 0 ; 63 ]. (30 by default)

<NoiseThres> indicates the noise threshold. Low value leads to high noise attenuation.
The threshold 32767 indicates no noise attenuation. The allowed range is [0 ;32767].
(8000 default)

<NmbTaps> indicates the Number of Taps of the Adaptive Filter. The allowed range
is [64 ;256]. (256 by default)-64 taps is for short Echo-256 taps is for long Echo.

25
Read Command: AT+ECHO?
This command returns the current settings of the Echo cancellation.
Returns: +ECHO: <Status>,<AlgoId>, <Param1>,<Param2>, <Param3>, <Param4>,
<Param5>,<Param6>
The number of parameters displayed depends on the algorythm used. For Echo
cancellation 1, 4 parameters are displayed, 3 parameters are displayed for Echo
cancellation 3.
<Status>
0: Echo Deactivated.
1: Echo Activated for Mic/Spk one.
2: Echo Activated for Mic/Spk two.
3:Reset the product.

PS: You can activate/deactivate the echo cancellation during a call without resetting the
product if the <AlgoId> parameter is not changed.

26
5.16 SideTone modification +SIDET

5.16.1 Description:
This specific command is used to set the level of audio feedback in the speaker
(microphone feedback in the speaker).

5.16.2 Syntax:
Command Syntax: AT+SIDET=<val1>,<val2>
COMMAND POSSIBLE RESPONSES
AT+SIDET=1,0 OK
Note: Command valid
AT+SIDET? +SIDET: 1,0
OK
Note: Current value Note: Command valid

5.16.3 Defined values:


<val1>
0: SideTone is disabled
1: SideTone is enabled

<val2>
0: 0 db
1: - 6 db
2: - 12 db
3: - 18 db

5.17 Initialize Voice Parameters +VIP

5.17.1 Description:
This command allows factory settings for voice parameters to be restored from EEPROM.
These voice parameters include:

❑ Gain control (+VGR & +VGT commands),


❑ Microphone mute control (+CMUT command),
❑ Speaker & Microphone selection (+SPEAKER command),
❑ Echo cancellation (+ECHO command),
❑ Side tone modification (+SIDET command).

27
5.17.2 Syntax:
Command Syntax: AT+VIP=<n>
COMMAND SYNTAX RETURN
AT+VIP=<n>
AT+VIP=? +VIP: 1
AT+VIP? +VIP: (1)
<n> =1 Restore all voice parameters.
COMMAND POSSIBLE RESPONSES
AT+VIP? +VIP: 1
OK
AT+VIP=2 +CME ERROR: 3
Note: Syntax error
AT+VIP=1 OK
Note: Restore the factory settings from EEPROM Note: The command has been executed
AT+VIP=1 CME ERROR: 519
Note: Restore the factory settings from EEPROM
with the current Echo cancellation algo (different
of the default algo). Note: Reset the product to accept the new algo.
AT+VIP=? +VIP: (1)
Note: List of supported <n>s OK

28
6 Network service commands

6.1 Signal Quality +CSQ

6.1.1 Description:
This command is used to ascertain the received signal strength indication (<rssi>) and the
channel bit error rate (<ber>) with or without a SIM card inserted.

6.1.2 Syntax:
Command Syntax: AT+CSQ
COMMAND POSSIBLE RESPONSES
AT+CSQ +CSQ: <rssi>,<ber>
OK
Note: <rssi> and <ber> as defined below

6.1.3 Defined values:


<rssi> :
0: -113 dBm or less
1: -111 dBm
30: -109 to –53 dBm
31: -51dBm or greater
99: not known or not detectable

<ber> :
0…7: as RXQUAL values in the table GSM 05.08
99: not known or not detectable

6.2 Operator selection +COPS

6.2.1 Description:
There are three possible ways of selecting an operator (PLMN):
➊ The product is in manual mode. It then tries to find the operator specified by the
application and if found, tries to register.
➋ The product is in automatic mode. It then tries to find the home operator and if found,
tries to register. If not found, the product automatically searches for another network.
➌ The product enters into manual/automatic mode, and then tries to find an operator as
specified by the application (as in manual mode). If this attempt fails it enters automatic
mode. If this is successful, the operator specified by the application is selected. The
mobile equipment then enters into automatic mode.

NOTE: The read command returns the current mode and the currently selected operator. In manual
mode, this PLMN may not be the one set by the application (as it is in the search phase).
These commands are not allowed during one communication.

29
6.2.2 Syntax:
To force an attempt to select and register on a network, the application must send the
following command:
Command syntax: AT+COPS=<mode>, [<format> [ , <oper> ] ]
Possible responses: AT+COPS=<mode>:
OK (Network is selected with full service)
+CME ERROR: 30 (No network service),
+CME ERROR: 32 (Network not allowed – emergency calls only)
+CME ERROR: 3 (Not allowed during one Communication)
+CME ERROR: 4 (Incorrect parameters)
+CME ERROR: 527 (Please wait, and retry your selection later)
+CME ERROR: 528 (Location update failure – emergency calls only)
+CME ERROR: 529 (Selection failure – emergency calls only)

Response syntax for AT+COPS?:


+COPS: <mode> [, <format>, <oper> ]
Response syntax for AT+COPS=?:
+COPS: [list of supported (<stat>, long alphanumeric <oper>, short alphanumeric <oper>s,
numeric <oper>) s]
If an incoming call occurs during a PLMN list request, the operation is aborted
(+CME ERROR: 520) and the unsolicited RING appears
COMMAND POSSIBLE RESPONSES
AT+COPS? +COPS: 0,2,20801
OK
Note: Ask for current PLMN Note: Home PLMN is France Telecom Orange
AT+COPS=? +COPS: (2,”F Itinéris”,”Itline”,”20801”), (3,”F
SFR”,”SFR”,”20810”)
OK
Note: Ask for PLMN list Note: Home PLMN is France Telecom SFR network has been
detected
AT+COPS=1,2,20810 +CME ERROR: 32
Note: Ask for registration on SFR network Note: Network not allowed – emergency calls only
AT+COPS=1,1,23433 +CME ERROR: 529
Note: Ask for registration on UK Orange network Note: Selection failed – emergency calls only
AT+COPS=0 OK
Note: Ask for registration on home network Note: Succeeded
AT+COPS=3,0 OK
Note: Set <format> to long alphanumeric
AT+COPS? +COPS: 0,0,”Orange F”
OK
Note: Ask for current PLMN Note: Home PLMN is France Telecom Orange
AT+COPS=2 OK
Note: Ask for deregistration from network Note: Succeeded
AT+COPS? +COPS: 2
Note: Ask for current PLMN Note: ME is unregistered until <mode>=0 or 1 is selected

30
6.2.3 Defined values:
The parameters values are the following ones:
<mode>
0: automatic (default value)
1: manual
2: deregistration ; ME will be unregistered until <mode>=0 or 1 is selected.
3: set only <format> (for read command AT+COPS?)
4: manual / automatic (<oper> shall be present), if manual selection fails, automatic mode
is entered.

<format>: format of <oper> field


<format>
0: long alphanumeric format <oper>
1: short alphanumeric format <oper>
2: numeric <oper> (default value) <stat>: status of <oper>

<stat>
0: unknown
1: available
2: current
3: forbidden

<oper>
Operator identifier (MCC/MNC in numeric format only for operator selection)
The long alphanumeric format can be up to 16 characters long (see appendix 18.12 for
operator names description, field is “Name”)
The short alphanumeric format can be up to 8 characters long.

31
6.3 Network registration +CREG

6.3.1 Description:
This command is used by the application to ascertain the registration status of the
product.

6.3.2 Syntax:
Command Syntax: AT+CREG= <mode>
Response Syntax: +CREG : <mode>, <stat> [ ,<lac>,<ci> ] for AT+CREG? Command only
COMMAND POSSIBLE RESPONSES
AT+CREG? +CREG: <mode>,<stat>
OK
Note: As defined here-above
AT+CREG=0 OK
Note: Disable network registration unsolicited result code Note: Command valid
AT+CREG=1 OK
Note: Enable network registration unsolicited result code Note: Command valid
AT+CREG=2 OK
Note: Enable network registration and location
information unsolicited result code Note: Command valid
AT+CREG=? +CREG: (0-2)
Note: 0,1,2 <mode> values are supported

6.3.3 Defined values:


<mode>
0: Disable network registration unsolicited result code (default)
1: Enable network registration code result code +CREG : <stat>
2: Enable network registration and location information unsolicited result code +CREG:
<stat>,<lac>,<ci> if there is a change of network cell.

<stat>
0: not registered, ME is not currently searching for a new operator.
1: registered, home network.
2: not registered, ME currently searching for a new operator to register to.
3: registration denied.
4: unknown.
5: registered, roaming.

<lac>
string type; two byte location area code in hexadecimal format (e.g. “00C3” equals 195 in
decimal).

<ci>
string type; two byte cell ID in hexadecimal format.

32
6.4 Read operator name +WOPN

6.4.1 Description:
This specific command returns the operator name in alphanumeric format when given the
numeric format.

6.4.2 Syntax:
Command syntax: AT+WOPN=<format>,<NumOper>
Response syntax: +WOPN: <format>,<AlphaOper>
COMMAND POSSIBLE RESPONSES
AT+WOPN=? OK
Note: Test command
AT+WOPN=0,20801 +WOPN : 0,”Orange F”
OK
Note: Give an operator in numeric format Note: Alphanumeric answer
AT+WOPN=0,99999 +CME ERROR: 22
Note: Give a wrong operator Note: Not found

6.4.3 Defined values:


<format> is the required format. Only long (0) and short (1) alphanumeric formats are
supported.
<NumOper> is the operator in numeric format.
<AlphaOper> is the operator in long or short alphanumeric format (see appendix 18.12 for
operator names description)

6.5 Preferred operator list +CPOL

6.5.1 Description:
This command is used to edit the SIM preferred list of networks.

6.5.2 Syntax:
Command Syntax: AT+CPOL= [ <index> ][ , <format> [ , <oper> ] ]
The different possibilities are:

❑ AT+CPOL = <index> to delete an entry.


❑ AT+CPOL = , <format> to set the format used by the read command (AT+CPOL?).
❑ AT+CPOL = , <format>, <oper> to put <oper> in the next free location.
❑ AT+CPOL = <index> , <format> , <oper> to write <oper> in the <format> at the <index>.
The supported format are those of the +COPS command.
The length of this list is limited to 8 entries.

33
COMMAND POSSIBLE RESPONSES
AT+CPOL? +CPOL:1,2,26201
+CPOL: 6,2,20810
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in numeric format
AT+CPOL=,0 OK
Note: Select long alphanumeric format
AT+CPOL? +CPOL: 1,0,”D1-TELEKOM”
+CPOL: 6,0,”F SFR”
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in long alphanumeric format
AT+CPOL=7,2,20801 OK
Note: Add a network to the list
AT+CPOL? CPOL: 1,0,”D1-TELEKOM”
+CPOL: 6,0,”F SFR”
+CPOL: 7,0,”Orange F”
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in long alphanumeric format
AT+CPOL=7 OK
Note: Delete 7th location
AT+CPOL? +CPOL: 1,0,”D1-TELEKOM”
+CPOL: 6,0,”F SFR”
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in long alphanumeric format
AT+CPOL=8,2,77777 OK
Note: Add a new network to the list
AT+CPOL? +CPOL: 1,0,”D1-TELEKOM”
+CPOL: 6,0,”F SFR”
+CPOL: 8,2,77777”
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in long alphanumeric format
but 8th entry is unknown so the product edits it in the
numeric format
AT+CPOL=9,0,”Orange F”
Note: Add a new network to the list (text format)
AT+CPOL? +CPOL: 1,0,”D1-TELEKOM”
+CPOL: 6,0,”F SFR”
+CPOL: 8,2,77777”
+CPOL: 9,0,”Orange F”
OK
Note: Ask for preferred list of networks Note: Preferred list of networks in long alphanumeric format

34
7 Security commands

7.1 Enter PIN +CPIN

7.1.1 Description:
This command is used to enter the ME passwords (CHV1 / CHV2 / PUK1 / PUK2, etc.), that
are required before any ME functionality can be used. CHV1/CHV2 is between
4 and 8 digits long, PUK1/PUK2 is only 8 digits long.
If the user application tries to make an outgoing call before the SIM PIN code (CHV1) has
been confirmed, then the product will refuse the “ATD” command with a “+CME ERROR:
11” (SIM PIN required).
The application is responsible for checking the PIN after each reset or power on - if the PIN
was enabled.

7.1.2 Syntax:
Command syntax: AT+CPIN=<pin>
COMMAND POSSIBLE RESPONSES
AT+CPIN=1234 OK
Note: Enter PIN Note: PIN code is correct
AT+CPIN=5678 +CME ERROR : 3
Note: Enter PIN Note: Operation not allowed, PIN previously entered

After 3 unsuccessful attempts to enter the PIN (Personal Identification Number), the PUK
(Personal Unblocking Key) will be required. PUK validation forces the user to enter a new PIN
code as a second parameter and this will be the new PIN code if PUK validation succeeds.
CHV1 is then enabled if PUK1 is correct. The application therefore uses this command:
AT+CPIN=<Puk>,<NewPin>
COMMAND POSSIBLE RESPONSES
AT+CPIN=00000000,1234 +CME ERROR: 16
Note: Enter PUK and new PIN Note: Incorrect PUK
AT+CPIN=12345678,1234 OK
Note: Enter PUK and new PIN, 2nd attempt Note: PUK correct, new PIN stored

To ascertain which code must be entered (or not), the following query command can be used:
AT+CPIN?
The possible responses are:
+CPIN: READY ME is not pending for any password
+CPIN: SIM PIN CHV1 is required
+CPIN: SIM PUK PUK1 is required
+CPIN: SIM PIN2 CHV2 is required
+CPIN: SIM PUK2 PUK2 is required
+CPIN: PH-SIM PIN SIM lock (phone-to-SIM) is required
+CPIN: PH-NET PIN Network personnalisation is required
+CME ERROR: <err> SIM failure (13) absent (10) etc…

35
Please note that in this case the mobile equipment does not end its response with
the OK string.
The response +CME ERROR : 13 (SIM failure) is returned after 10 unsuccessful PUK
attempts. The SIM card is then out of order and must be replaced by a new one.
Example: 3 failed PIN validations + 1 successful PUK validation

AT+CPIN?
+CPIN: SIM PIN Read the PIN status
The product requires SIM PIN
AT+CPIN=1235
+CME ERROR: 16 First attempt to enter a SIM PIN
Wrong PIN
AT+CPIN=1236
+CME ERROR: 16 Second attempt
Wrong PIN
AT+CPIN=1237
+CME ERROR: 16 Third attempt
Wrong PIN
AT+CPIN?
+CPIN: SIM PUK Read PIN state
The product requires PUK
AT+CPIN=99999999,5678
OK The PUK is entered, the new PIN shall be 5678 PUK validation is OK. New Pin is 5678
AT+CPIN? Read PIN state
+CPIN: READY The product is ready

If the user tries to do something which requires PIN2 (CHV2), the product will refuse the
action with a “+CME ERROR: 17” (SIM PIN2 required). The product then waits for SIM
PIN2 to be given.
Of course, if SIM PIN2 is blocked, SIM PUK2 is required instead of SIM PIN2.
For example, the product needs PIN2 to write in the fixed dialling phonebook (FDN), so if
SIM PIN2 authentication has not been performed during the current session, SIM PIN2 is
required.

36
COMMAND POSSIBLE RESPONSES
AT+CPBS=”FD” OK
Note: Choose FDN
AT+CPBW=5,”01290917”,129,”Jacky” +CME ERROR: 17
Note: Write in FDN at location 5 Note: SIM PIN2 is required
AT+CPIN? SIM PIN2
Note: SIM PIN2 is required
AT+CPIN=5678 OK
Note: Enter SIM PIN2
AT+CPBW=2,”01290917”,129,”Jacky” OK
Note: Write in FDN at location 5 Note: Now writing in FDN is allowed

Please note that the product only requests PIN2 or PUK2 once. Therefore, if they are not
entered properly, the next +CPIN? command will return “+CPIN: READY”.

7.2 Enter PIN2 +CPIN2

7.2.1 Description:
This specific command is used to validate the PIN2 code (CHV2), or to validate the PUK2
code (UNBLOCK CHV2) and to define a new PIN2 code.
Of course, the +CPIN command allows PIN2 or PUK2 codes to be validated, but only when
the last command executed resulted in PIN2 authentication failure.
PIN2 length is between 4 and 8 digits, PUK2 length is 8 digits only.

7.2.2 Syntax:
Command Syntax: AT+CPIN2=<pin2>
COMMAND POSSIBLE RESPONSES
AT+CPIN2=1234 OK
Note: Enter PIN2 Note: PIN2 code is correct
AT+CPIN2=5678 +CME ERROR: 3
Note: Enter PIN2 Note: Operation not allowed, PIN2 previously entered

After 3 unsuccessful attempts, PUK2 will then be required. PUK2 validation forces the user
to enter a new PIN2 code as a second parameter and this will be the new PIN2 code if
PUK1 validation succeeds. The application therefore uses this command:
AT+CPIN2=<puk2>,<NewPin2>
COMMAND POSSIBLE RESPONSES
AT+CPIN2=00000000,1234 +CME ERROR: 16
Note: Enter PUK2 and new PIN2 Note: Incorrect Password (PUK2)
AT+CPIN2=12345678,1234 OK
Note: Enter PUK2 and new PIN2, 2nd attempt Note: PUK2 correct, new PIN2 stored

37
To ascertain which code must be entered (or not), the following query command can be
used:
AT+CPIN2?
The possible responses are:

+CPIN2: READY No PIN2 is needed


+CPIN2: SIM PIN2 PIN2 is required
+CPIN2: SIM PUK2 PUK2 is required
+CME ERROR: <err> Absent (10) etc…

7.3 PIN remaining attempt number +CPINC

7.3.1 Description:
This specific command is used to get the number of valid attempts for PIN1 (CHV1), PIN2
(CHV2), PUK1 (UNBLOCK CHV1) and PUK2 (UNBLOCK CHV2) identifiers.

7.3.2 Syntax:
Command Syntax: AT+CPINC
Response Syntax: +CPINC : <n1>,<n2>,<k1>,<k2>
COMMAND POSSIBLE RESPONSES
AT+CPINC +CPINC : 2,3,10,10
Note: Get the number of attempts left Note: First CHV1 attempt was a failure
AT+CPINC? +CPINC : 2,3,10,10
Note: Get current values Note: First attempt was a failure
AT+CPINC=? OK
Note: Get possible values

7.3.3 Defined values


<n1>, <n2> are the attempts left for PIN1, PIN2 (0 = blocked, 3 max)
<k1>, <k2> are the attempts left for PUK1, PUK2 (0 = blocked, 10 max)
For this to work, the card should be present at the time of initialization, otherwise an error
will be sent (+CME ERROR : 10).

38
7.4 Facility lock +CLCK

7.4.1 Description:
This command is used by the application to lock, unlock or interrogate an ME or network
facility <fac>.
NOTE: Test SIM cards (with MCC=001 & MNC=01) doesn’t check “PS”, “PN”, “PU”, “PP” and “PC”
locks.

7.4.2 Syntax:
Command syntax: AT+CLCK= <fac>,<mode>[,<passwd>[,<class>] ]
Response syntax: +CLCK: <status> [ ,<class1> ]<CR><LF>+CLCK: <status>,<class2> [ … ] ]
COMMAND POSSIBLE RESPONSES
AT+CLCK=”SC”,1,1234 OK
Note: Enable PIN Note: PIN was correct
AT+CLCK? +CLCK:(“PS”,0),(“SC”,0),(“FD”,0),(“PN“,0),(“PU“,0),
(“PP“,0),(“PC“,0)
OK
Note: Read PIN status Note: PIN is enabled, no SIM lock, no network lock, no infor-
mation on Call barring (no longer supported in GSM 07.07)
AT+CLCK=”SC”,0,5555 +CME ERROR: 16
Note: Disable PIN Note: PIN was wrong
AT+CPIN=1234 OK
Note: Enter PIN Note: PIN was good
AT+CLCK=? +CLCK:(“PS”,”SC”,”AO”,”OI”,”OX”,”AI”,”IR”,”AB”,
”AC”, ”FD”,"PN","PU","PP",”PN”)
OK
Note: Request supported facilities Note: Supported facilities
AT+CLCK=”PN”,1,12345678 OK
Note: Activate network lock Network lock activated
AR+CLCK=”AO”,1,1234,2 OK
Note: Activate all outgoing calls barring for data calls Note: Call barring is activate
AT+CLCK=”AO”,2 +CLCK : 1,2
OK
Note: Query BAOC status Note: BAOC activate for data calls only
AT+CLCK=”SC”,0,0000 +CME ERROR: 521
Note: Disable PIN Note: PIN deactivation is forbidden with this SIM card

39
7.4.3 Defined values:
The following <fac> values are supported:
“PS”: SIM lock facility with a 8 digits password.
“SC“: PIN enabled (<mode> = 1) / disabled (<mode> = 0)
“AO”: BAOC (Barr All Outgoing Calls)
“OI”: BOIC (Barr Outgoing International Calls)
“OX”: BOIC-exHC (Barr Outgoing. International Calls except to Home Country)
“AI”: BAIC (Barr All Incoming Calls)
“IR”: BIC-Roam (Barr Inc. When Roaming outside Home Country)
“AB”: All Barring services
“AG”: All outGoing barring services
“AC”: All inComing barring services
“PN”: Network lock with a 8 digits password (NCK).
“PU”: Network Subset lock with a 8 digits password (NSCK).
“PP”: Service Provider lock with a 8 digits password (SPCK).
“PC”: Corporate lock with a 8 digits password (CCK).
“FD”: SIM Fixed Dialing Numbers (FDN) memory feature (PIN2 is required as <password>)

<mode>
0: unlock the facility
1: lock the facility
2: query status

<class>
A facility status can be changed for only one class, or for all classes (7 or omitted).
<class>
1: Voice (telephony)
2: Data (apply to all bearer services)
4: Fax (facsimile services)
8: Short Message service
7: Equal to all classes (Default value)

Any attempt to combine different classes will result in activation / deactivation /


interrogation of all classes.
Password maximum length is given with the AT+CPWD=? Command.
NOTE: It will not possible to lock the FDN phonebook if this one is not loaded.

40
7.5 Change password +CPWD

7.5.1 Description:
This command is used by the application to change a password (PIN, call barring, NCK,
etc.). The facility values (<fac>) are the same as for the +CLCK command with a “P2”
facility to manage SIM PIN2.
For the network lock (“PN”), unlocking is forbidden after 10 failed attempts to disable
(unlock) the network lock with an incorrect password.

7.5.2 Syntax:
Command Syntax: AT+CPWD= <fac>, <oldpwd>, <newpwd>
COMMAND POSSIBLE RESPONSES
AT+CPWD=? +CPWD: (“PS”,8),(“SC”,8),(“AO”,4),(“OI”,4),(“OX”,4),
(“AI”,4),(“IR,4),(“AB”,4),(“AG”,4),(“AC”,4),
(“P2”,8),(“FD”,8),("PN",8),("PU",8),("PP",8), ("PC",8)
OK
Note: Possible values Note: CHV1/CHV2 must be on 8 digits maximum (4mn)
For call barring, on 4 digits maximum
AT+CPWD=”SC”,1234,5555 OK
Note: Change PIN Note: PIN was correct
AT+CPWD=”SC”,1234,5555 +CME ERROR: 16
Note: Change PIN Note: PIN was wrong
AT+CPIN=5555 OK
Note: Enter PIN Note: PIN was correct
AT+CPWD=”PN”,12345678,00000000 OK
Note: Change NCK Note: NCK changed for net lock

41
8 Phonebook commands

8.1 Select phonebook memory storage +CPBS

8.1.1 Description:
This command selects phonebook memory storage. The available phonebooks are:
“SM“: ADN (SIM phonebook)
“FD”: FDN (SIM Fix Dialling, restricted phonebook)
“ON”: MSISDN (SIM own numbers)
“EN”: EN (SIM emergency number)
“LD”: LND (combined ME and SIM last dialing phonebook)
“MC”: MSD (ME missed calls list)
“ME”: ME (ME phonebook)
“MT”: MT (combined ME and SIM phonebook)
“RC”: LIC (ME received calls list)
“SN”: SDN (Services dialing phonebook)

8.1.2 Syntax:
Command Syntax: AT+CPBS
COMMAND POSSIBLE RESPONSES
AT+CPBS=”SM” OK
Note: Select ADN phonebook Note: ADN phonebook is selected
AT+CPBS=? +CPBS: ("SM","LD","MC","ON","ME","RC","MT","SN")
OK
Note: Possible values Note: only “EN” phonebook is not supported with this SIM card.
AT+CPBS? +CPBS :”SM”,10,20
OK
Note: Status Note: ADN phonebook selected, 10 locations used,
20 locations available

The ADN phonebook could not be selected as FDN is active.

42
8.2 Read phonebook entries +CPBR

8.2.1 Description:
This command returns phonebook entries for a range of locations from the current
phonebook memory storage selected with +CPBS.
Note: for all phonebook read commands (+CPBR, +CPBF, +CPBN, +CPBP, +CNUM), the TON/NPI MSB
of each number is set to 1 (ex : a TON/NPI stored as 17 is displayed as 145).

8.2.2 Syntax:
Command Syntax: AT+CPBR
COMMAND POSSIBLE RESPONSES
AT+CPBR=? +CPBR: (1-50),20,10
OK
Note: Test command Note: 50 locations (from 1 to 50), max length for phone
number is 20 digits, 10 characters max for the text
AT+CPBR=12,14 +CPBR : 12,”112”,129,”Emergency”
+CPBR : 13,”+331290909”,145,”Fred”
+CPBR : 14,”0146290808”,129,”Zazi”
OK
Note: Read entries from 12 to 14 Note: Display locations 12,13,14 with location, number,
type (TON/NPI), Text
AT+CPBR=10 +CPBR :10,”0146290921”,129,”Rob”
OK
Note: Read entry 10 Note: Display location 10
AT+CPBR=11 +CPBR :11,”0146290921”,129,”8000010002FFFF”
OK
Note: Read entry 11 (UCS2 format) Note: Display location 11
AT+CPBR=52 +CME ERROR: 21
Note: Read entry 52 (wrong) Note: Invalid index

43
8.3 Find phonebook entries +CPBF

8.3.1 Description:
This command returns phonebook entries with alphanumeric fields starting with a given
string. The AT+CPBF= “” command can be used to display all phonebook entries sorted in
alphabetical order.
This command is not allowed for "LD", "RC", "MC", "SN" phonebooks and for the “EN”
phonebook, which does not contain alphanumeric fields.
It is possible to use this command with UCS2 strings. If a wrong UCS2 format is entered,
the string is considered as an ASCII string.

8.3.2 Syntax:
Command Syntax: AT+CPBF
COMMAND POSSIBLE RESPONSES
AT+CPBF=? +CPBF: 20,10
OK
Note: Test command Note: Max length for phone number is 20 digits, 10
characters for the text
AT+CPBF=“E” +CPBF : 12,”112”,129,”Emergency”
+CPBF : 15,”+331290101”,145,”Eric”
OK
Note: Read entries with “E” Note: Display locations with text field starting with “E”
AT+CPBF=”H” +CME ERROR: 22
Note: Read entries with “H” Note: Entry not found
AT+CPBF=”800001FFFF” +CPBF : 11, ”0146290921”,129,”8000010002FFFF”
OK
Note: Read entries starting with 0001 UCS2 character Note: Display locations with text field starting with 0001
UCS2 character
AT+CPBF=”8045C” +CME ERROR: 22
Note: Read entries with “8045C” (ASCII format) Note: Entry not found. The string has a wrong UCS2 format,
it is therefore considered as an ASCII string

44
8.4 Write phonebook entry +CPBW

8.4.1 Description:
This command writes a phonebook entry in location number <index> in the current
phonebook memory storage.
“RC” and “MC” phonebooks could be only erased by +CPBW. Adding field and/or
modifying field is not allowed for these phonebooks.
This command is not allowed for “EN”, “LD”, “MC”, “RC”, “MT”, “SN” phonebooks,
which can not be written.

8.4.2 Syntax:
Command Syntax: AT+CPBW=<index>[,<number>[,<type>[,<text>]]]
COMMAND POSSIBLE RESPONSES
AT+CPBW=? +CPBW: (1-50),20,(129,145),10
OK
Note: Test command Note: 50 locations, phone number = 20 digits max, TON/NPI
of 129 or 145, text length = 10
AT+CPBW= 3 OK
Note: Erase location 3 Note: Location 3 erased
AT+CPBW=5,”112”,129,”SOS” OK
Note: Write at location 5 Note: Location 5 written
AT+CPBW=5,”01290917”,129,”Jacky” OK
Note: Overwrite location 5 Note: Location 5 overwritten
AT+CPBW=6,”01292349”,129,”8000410042” OK
Note: write location 6 (UCS2 format for the <text> field) Note: Location 6 is written
AT+CPBW=,”+33145221100”,145,”SOS” OK
Note: Write at the first location available Note: First location available is written
AT+CPBW=,”0345221100”,129,”SOS” +CME ERROR: 20
Note: Write at the first location available Note: Phonebook full
AT+CPBW=57,”112”,129,”WM” +CME ERROR: 21
Note: Write at location 57 (wrong)Note: Invalid index
AT+CPBW=7,”012345678901234567890”,129,”WAVE” +CME ERROR: 26
Note: Write at location 7 a phone number
exceeding the limit (21 digits) Note: Phone number too long
AT+CPBW=7,”0122334455”,129,”WAVECOM TEL” +CME ERROR: 24
Note: Write at location 7 along text (11 characters) Note: Text too long
AT+CPBW=8,”01292349”,129,”80xyz” OK
Note: write location Note: Location 8 is written. The string has a wrong UCS2
format, it is therefore considered as an ASCII string

45
When the fixed dialling phonebook (FDN) is locked, this command is not allowed.
Moreover, when the FDN is unlocked, PIN2 is required to write in the FDN phonebook.
But if PIN2 authentication has been performed during the current session, the +CPBW
command with FDN is allowed.

COMMAND POSSIBLE RESPONSES


AT+CPBS=”FD” OK
Note: Choose FDN
AT+CPBW=5,”01290917”,129,”Jacky” +CME ERROR: 17
Note: Write in FDN at location 5 Note: SIM PIN2 is required
AT+CPIN? SIM PIN2
Note: SIM PIN2 is required
AT+CPIN=5678 OK
Note: Enter SIM PIN2
AT+CPBW=5,”01290917”,129,”Jacky” OK
Note: Write in FDN at location 5 Note: Writing in FDN is now allowed

8.4.3 Defines values:


<index> integer type value depending on the capacity of the phonebook memory.
<number> phone number in ASCII format.
<type> TON/NPI (Type of address octet in integer format).

NOTE: for the <type> parameter, all values are allowed from 0 to 255, but the MSB will be set to 1 in all
cases (ex : a <type> value of 17 will be written as 145).

<text> string type.


NOTE 1: For the <text> parameter all strings starting with “80” , “81” or “81” are considered in UCS2
format. See the APPENDIX E (Coding of Alpha fields in the SIM for UCS2).

NOTE 2: The +CSCS (Select Character set) command does not affect the format for phonebook entries.

46
8.5 Phonebook phone search +CPBP

8.5.1 Description:
This specific command orders the product to search the phonebook for an item with the
same phone number as that defined in the parameter.

8.5.2 Syntax:
Command Syntax: AT+CPBP=<PhoneNumber>
<PhoneNumber> is coded like any GSM 07.07 or GSM 07.05 phone number.
COMMAND POSSIBLE RESPONSES
AT+CPBP=”+331290101” +CPBP : 15,”+331290101”,145,”Eric”
OK
Note: Search entries corresponding to this phone number Note: Display the entry corresponding to the specified phone number
AT+CPBP=”+331290101” +CPBP : 15,”01290101”,129,”Eric”
OK
Note: Search entries corresponding to this phone number Note: Display the entry corresponding to the specified phone number
AT+CPBP=”01290202” +CPBP : 15,”+331290202”,145,”David”
OK
Note: Search entries corresponding to this phone number Note: Display the entry corresponding to the specified phone number
AT+CPBP=”+331288575” +CPBP : 15,”+331290101”,145,”8045682344FFFF”
(UCS2 format)
OK
Note: Search entries corresponding to this phone number Note: Display the entry corresponding to the specified phone number
AT+CPBP=”0129” +CME ERROR: 22
Note: Search entries corresponding to this phone number Note: Entry not found

47
8.6 Move action in phonebook +CPBN

8.6.1 Description
This specific command instructs the product to make a forward or backward move in the
phonebook (in alphabetical order).
This command is not allowed for the “EN” phonebook - which does not contain
alphanumeric fields.

8.6.2 Syntax:
Command Syntax: AT+CPBN=<mode>
COMMAND POSSIBLE RESPONSES
AT+CPBN=? +CPBN: (0-5)
OK
Note: Test command Note: Possible modes
AT+CPBN=0 +CPBN : 15,”+331290101”,145,”Eric”
OK
Note: Read the first location Note: Display the first location
AT+CPBN=2 +CPBN : 5,”+33147658987”,145,”Frank”
OK
Note: Read the next location Note: Display the second location
AT+CPBN=2 +CPBN : 6,”+331290302”,145,”Marc”
OK
Note: Read the next location Note: Display the third location
AT+CPBN=3 +CPBN : 5,”+33147658987”,145,”Frank”
OK
Note: Read the previous location Note: Display the second location
AT+CPBN=1 +CPBN : 6,”+331290302”,145,”Marc”
OK
Note: Read the last location Note: Display the last location
AT+CPBN=2 +CPBP : 15,”+331290101”,145,”Eric”
OK
Note: Read the next location Note: Display the first location

48
Using mode 4 and 5 with +CPBF command and CPBW :
COMMAND POSSIBLE RESPONSES
AT+CPBF=”Er” +CPBF : 15,”+331290101”,145,”Eric”
OK
Note: Find ”Er” in phonebook Note: Display the location
AT+CPBN=2 +CPBN : 5,”+33147658987”,145,”Frank”
OK
Note: Read the next location Note: Display the following location
AT+CPBF=”Er” +CPBF : 15,”+331290101”,145,”Eric”
OK
Note: Find ”Er” in phonebook Note: Display the location
AT+CPBN=4 +CPBF : 15,”+331290101”,145,”Eric”
OK
Note: Get the last location read Note: Display the last location read
AT+CPBW=,”0146290800”,129,”WM” OK
Note: Write an item at the first location available Note: No information about this location
AT+CPBN=4 +CPBF : 15,”+331290101”,145,”Eric”
OK
Note: Get the last location read Note: Display the last location read
AT+CPBN=38,”0146290800,129,”WM”
Note: Display the last item written with its location
AT+CPBN=4 AT+CPBN=38,”0146290800,129,”WM”
Note: Get the last item read Note: Now the last item read is the last written item too
AT+CPBF=”800041FFFF” +CPBF : 15,”+3312345”,145,”8000414339FFFF”
OK
Note: Find”800041” in phonebook Note: Display this location
AT+CPBN=4 +CPBF : 15,”+3312345”,145,”8000414339FFFF”
OK
Note: Get the last location read Note: Display the last location read

Please note that the AT+CPBN=5 command is useful after an AT+CPBW command used
without a location.

8.6.3 Defined values:


<mode>
0: First item
1: Last item
2: Next valid item in alphabetical order
3: Previous valid item in alphabetical order
4: Last item read (usable only if a read operation has been performed on the current
phonebook since the end of initialization (+WIND: 4))
5: Last item written (usable only if a write operation has been performed on the current
phonebook since the end of initialization (+WIND: 4))

49
8.7 Subscriber number +CNUM

8.7.1 Description:
This command returns the subscriber MSISDN(s).
If the subscriber has different MSISDNs for different services, each MSISDN is returned in
a separate line.

8.7.2 Syntax:
Command syntax: AT+CNUM
Response syntax: +CNUM : <alpha1>, <number1>, <type1>
<CR><LF> +CNUM : <alpha2>, <number2>, <type2> ….
COMMAND POSSIBLE RESPONSES
AT+CNUM +CNUM :”Phone”, “0612345678”,129
+CNUM :”Fax”, “0687654321”,129
+CNUM :”80001002FFFF”, “+0183773”, 145 (UCS2 format)
Note: Get MSISDN(s) Note: MSISDNs
AT+CNUM=? OK

8.7.3 Defined values:


<alphax> optional alphanumeric string associated with <numberx>
<numberx> string type phone number with format as specified by <typex>
<typex> type of address byte in integer format

50
8.8 Avoid phonebook init +WAIP

8.8.1 Description:
This specific command allows the initialization of all phonebooks to be inhibited during
subsequent boots.

8.8.2 Syntax:
Command Syntax: AT+WAIP=<mode>
COMMAND POSSIBLE RESPONSES
AT+WAIP? +WAIP :0
OK
Note: Current values ? Note: Default value (init phonebooks)
AT+WAIP=? +WAIP : (0,1)
OK
Note: Possible values ? Note: Disable / enable
AT+WAIP =1 OK
Note: Inhibit initialization of phonebooks (next boot) Note: no answer
AT&W
Note: Save modifications in EEPROM

Caution: the given value should be stored in EEPROM. Therefore, the AT&W command must be used
to save the new <mode> value.
NOTE: No phonebook commands are allowed if +WAIP=1 (after boot).
If a phonebook command is entered, a “+CME ERROR: 3” is returned.

8.8.3 Defined values:


<mode>
0: Normal initialization (with phonebooks)
1: No phonebook initialization

51
8.9 Delete Calls Phonebook +WDCP

8.9.1 Description:
This specific command allows to delete the calls listed in some phonebooks.

8.9.2 Syntax:
Command Syntax: AT+WDCP=<calls phonebook>
COMMAND POSSIBLE RESPONSES
AT+WDCP? OK
AT+WDCP=? +WDCP : ("LD","MC","RC")
OK
Note: Possible values ? Note: Identifiers of the phonebooks supporting a list of calls
AT+WDCP=”LD” OK
Note: Delete all the content of Last Dialing phonebook. Note: Last Dialing phonebook is now empty.

8.9.3 Defined values:


<calls phonebook>
“LD”: SIM (ME extended) Last dialing phonebook
“MC”: ME missed calls list phonebook
“RC”: ME received calls list phonebook

8.10 Set Voice Mail Number +CSVM

8.10.1 Description:
This commands allows to set/get and enable/disable the voice mail number in memory.

8.10.2 Syntax:
Command Syntax: AT+CSVM=<mode>[,<number>[,<type>]]
COMMAND POSSIBLE RESPONSES
AT+CSVM? +CSVM: 1,”660”,129
OK
Note: Get mail number Note: Voice mail number “660” is activated
AT+CSVM=? +CSVM: (0-1),(129,145)
OK
Note: Possible values ? Note: activation/deactivation and format 129 & 145 are
supported
AT+CSVM=0,”888”,129 OK
Note: Disable Voice Mail number and
change value to “888”.

52
8.10.3 Defined values:
<mode>
0: Disable the voice mail number
1: Enable the voice mail number

<number>
Phone number in ASCII format.

<type>
TON/NPI (Type of address byte in integer format).

NOTE: For the <type> parameter, all values are allowed from 0 to 255, but the MSB will be set to 1 in
all cases (ex : a <type> value of 17 will be written as 145).

53
9 Short Messages commands

9.1 Parameters definition


<da> Destination Address, coded like GSM 03.40 TP-DA
<dcs> Data Coding Scheme, coded like in document [5].
<dt> Discharge Time in string format :
“yy/MM/dd,hh :mm :ss±zz”(Year [00-99], Month [01-12],
Day [01-31], Hour, Minute, Second and Time Zone [quarters of an hour] )
<fo> First Octet, coded like SMS-SUBMIT first octet in document [4], default value is
17 for SMS-SUBMIT
<index> Place of storage in memory.
<length> Text mode (+CMGF=1): number of characters PDU mode (+CMGF=0):
length of the TP data unit in octets
<mem1> Memory used to list, read and delete messages (+CMGL, +CMGR and
+CMGD).
<mem2> Memory used to write and send messages (+CMGW, +CMSS).
<mid> CBM Message Identifier.
<mr> Message Reference.
<oa> Originator Address.
<pid> Protocol Identifier.
<pdu> For SMS : GSM 04.11 SC address followed by GSM 03.40 TPDU in
hexadecimal format, coded as specified in doc [4] For CBS : GSM 03.41
TPDU in hexadecimal format
<ra> Recipient Address.
<sca> Service Center Address
<scts> Service Center Time Stamp in string format : “yy/MM/dd,hh :mm :ss±zz”
(Year/Month/Day,Hour:Min:Seconds±TimeZone)
<sn> CBM Serial Number
<st> Status of a SMS-STATUS-REPORT
<stat> Status of message in memory.
<tooa> Type-of-Address of <oa>.
<tora> Type-of-Address of <ra>.
<tosca> Type-of-Address of <sca>.
<total1> Number of message locations in <mem1>.
<total2> Number of messages locations in <mem2.
<used1> Total number of messages locations in <mem1>.
<used2> Total number of messages locations in <mem2.
<vp> Validity Period of the short message, default value is 167

54
9.2 Select message service +CSMS

9.2.1 Description:
The supported services are originated (SMS-MO) and terminated short message (SMS-
MT) + Cell Broadcast Message (SMS-CB) services.

9.2.2 Syntax:
Command Syntax: AT+CSMS=<service>
COMMAND POSSIBLE RESPONSES
AT+CSMS=0 +CSMS: 1,1,1
OK
Note: SMS AT command Phase 2 version 4.7.0 Note: SMS-MO, SMS-MT and SMS-CB supported
AT+CSMS=1 +CSMS: 1,1,1
Note: SMS AT command Phase 2 + Note: SMS-MO, SMS-MT and SMS-CB supported
AT+CSMS? +CSMS: 0,1,1,1
OK
Note: Current values ? Note: GSM 03.40 and 03.41 (SMS AT command Phase 2
version 4.7.0
AT+CSMS=? +CSMS: (0,1)
Note: Possible services OK

9.2.3 Defined values:


<service>
0: SMS AT commands are compatible with GSM 07.05 Phase 2 version 4.7.0.
1: SMS AT commands are compatible with GSM 07.05 Phase 2 + version .

55
9.3 New Message Acknowledgement +CNMA

9.3.1 Description:
This command allows reception of a new message routed directly to the TE to be
acknowledged.
In TEXT mode, only positive acknowledgement to the network (RP-ACK) is possible.
In PDU mode, either positive (RP-ACK) or negative (RP-ERROR) acknowledgement to the
network is possible.
Acknowledge with +CNMA is possible only if the +CSMS parameter is set to 1 (+CSMS=1)
when a +CMT or +CDS indication is shown (see +CNMI command).
If no acknowledgement is given within the network timeout, an RP-ERROR is sent to the
network, the <mt> and <ds> parameters of the +CNMI command are then reset to zero (do
not show new message indication).

9.3.2 Syntax:
Command syntax in text mode :
AT+CNMA
Command syntax in PDU mode :
AT+CNMA [ = <n> [ , <length> [ <CR>
PDU is entered <ctrl-Z / ESC> ] ] ]
NOTE: PDU is entered using <ackpdu> format instead of <pdu> format (e.g.. SMSC address field
is not present).
Example of acknowledgement of a new message in TEXT mode:
COMMAND POSSIBLE RESPONSES
AT+CMGF=1 OK
Note: Set TEXT mode Note: TEXT mode valid
AT+CNMI=2,2,0,0,0 OK
Note: <mt>=2
+CMT : “123456”,”98/10/01,12 :30 00+00”,129,4
,32,240, “15379”,129,5<CR><LF>
Received message
Note: message received
AT+CNMA OK
Note: acknowledge the message received Note: send positive acknowledgement to the network
AT+CNMA +CMS ERROR : 340
Note: try to acknowledge again Note: no +CNMA acknowledgment expected

56
Example of acknowledgement of a new message in PDU mode:
COMMAND POSSIBLE RESPONSES
AT+CMGF=0 OK
Note: Set PDU mode Note: PDU mode valid
+CMT: ,29
07913366003000F1240B913366920547F3000000300341940
4800B506215D42ECFE7E17319
Note: message received
AT+CNMA=2,<length> <CR> OK
… Pdu message … <Ctrl-Z/ESC>
Note: negative acknowledgement for the message. Note: send a negative acknowledgement to the network (RP-
ERROR) with PDU message (<ackpdu> format).

9.3.3 Defined values:


<n>: Type of acknowledgement in PDU mode
0: send RP-ACK without PDU (same as TEXT mode)
1: send RP-ACK with optional PDU message
2: send RP-ERROR with optional PDU message
<length>: Length of the PDU message

57
9.4 Preferred Message Storage +CPMS

9.4.1 Description:
This command allows the message storage area to be selected (for reading, writing, etc).

9.4.2 Syntax:
Command Syntax: AT+CPMS=<mem1>,[<mem2>]
COMMAND POSSIBLE RESPONSES
AT+CPMS=? +CPMS: ((“SM”,”BM”,”SR”),(“SM”))
OK
Note: Possible message storages Note: Read, list, delete: SMS, CBM or SMS Status Report
Write, send: SMS
AT+CPMS? +CPMS: “SM”,3, 10,”SM”,3,10
OK
Note: Read Note: Read, write…SMS from/to SIM
3 SMS are stored in SIM. 10 is the total memory available
in SIM
AT+CPMS=”AM” +CMS ERROR: 302
Note: Select false message storage
AT+CPMS=”BM” +CPMS: 2,20,3,10
OK
Note: Select CBM message storage Note: Read, list, delete CBM from RAM 2 CBM a
re stored in RAM
AT+CPMS? +CPMS: “BM”,2,20,”SM”,3,10
OK
Note: Read Note: Read list, delete CBM from RAM
Write SMS to SIM

9.4.3 Defined values:


<mem1>: Memory used to list, read and delete messages. It can be:
“SM”: SMS message storage in SIM (default)
“BM”: CBM message storage (in volatile memory).
“SR” : Status Report message storage (in SIM if the EF-SMR file exists, otherwise in the
ME non volatile memory)
NOTE: “SR” ME non volatile memory is cleared when another SIM card is inserted. It is kept, even
after a reset, while the same SIM card is used.

<mem2>: Memory used to write and send messages


“SM”: SMS message storage in SIM (default).
If the command is correct, the following message indication is sent:
+CPMS: <used1>,<total1>,<used2>,<total2>
When <mem1> is selected, all following +CMGL, +CMGR and +CMGD commands are
related to the type of SMS stored in this memory.

58
9.5 Preferred Message Format +CMGF

9.5.1 Description:
The message formats supported are text mode and PDU mode.
In PDU mode, a complete SMS Message including all header information is given as a
binary string (in hexadecimal format). Therefore, only the following set of characters is
allowed: {‘0’,’1’,’2’,’3’,’4’,’5’,’6’,’7’,’8’,’9’, ‘A’, ‘B’,’C’,’D’,’E’,’F’}. Each pair or characters is
converted to a byte (e.g.: ‘41’ is converted to the ASCII character ‘A’, whose ASCII code is
0x41 or 65).
In Text mode, all commands and responses are in ASCII characters.
The format selected is stored in EEPROM by the +CSAS command.

9.5.2 Syntax:
Command Syntax: AT+CMGF
COMMAND POSSIBLE RESPONSES
AT+CMGF ? +CMGF: 1
OK
Note: Current message formatNote: Text mode
AT+CMGF=? +CMGF: (0-1)
OK
Note: Possible message format Note: Text or PDU modes are available

Example, sending an SMS Message in PDU mode


COMMAND POSSIBLE RESPONSES
AT+CMGF=0 OK
Note: Set PDU mode Note: PDU mode valid
AT+CMGS=14<CR> +CMGS: 4
0001030691214365000004C9E9340B OK
Note: Send complete MSG in PDU mode, no SC address Note: MSG correctly sent, <mr> is returned

59
9.5.3 Defined values:
The <pdu> message is composed of the SC address (« 00 means no SC address given, use
default SC address read with +CSCA command) and the TPDU message.
In this example, the length of octets of the TPDU buffer is 14, coded as GSM 03.40
In this case the TPDU is : 0x01 0x03 0x06 0x91 0x21 0x43 0x65 0x00 0x00 0x04 0xC9 0xE9
0x34 0x0B, which means regarding GSM 03.40 :

<fo> 0x01 (SMS-SUBMIT, no validity period)


<mr> (TP-MR) 0x03 (Message Reference)
<da> (TP-DA) 0x06 0x91 0x21 0x43 0x65 (destination address +123456)
<pid> (TP-PID) 0x00 (Protocol Identifier)
<dcs> (TP-DCS) 0x00 (Data Coding Scheme : 7 bits alphabet)
<length> (TP-UDL) 0x04 (User Data Length, 4 characters of text)
TP-UD 0xC9 0xE9 0x34 0x0B (User Data : ISSY)

TPDU in hexadecimal format must be converted into two ASCII characters, e.g. octet with
hexadecimal value 0x2A is presented to the ME as two characters ‘2’ (ASCII 50) and ‘A’
(ASCII 65).

9.6 Save Settings +CSAS

9.6.1 Description:
All settings specified by the +CSCA and +CSMP commands are stored in EEPROM if the
SIM card is a Phase 1 card or in the SIM card if it is a Phase 2 SIM card.

9.6.2 Syntax:
Command Syntax: AT+CSAS
COMMAND POSSIBLE RESPONSES
AT+CSAS OK
Note: Store +CSAS and +CSMP parameters Note: Parameters saved

9.7 Restore settings +CRES

9.7.1 Description:
All settings specified in the +CSCA and +CSMP commands are restored from EEPROM if
the SIM card is Phase 1 or from the SIM card if it is a Phase 2 SIM card.

9.7.2 Syntax:
Command Syntax: AT+CRES
COMMAND POSSIBLE RESPONSES
AT+CRES OK
Note: Restore +CSAS and +CSMP parameters Note: Parameters restored

60
9.8 Show text mode parameters +CSDH

9.8.1 Description:
This command gives additional information on text mode result codes. This information is
given in brackets in the +CMTI, +CMT, +CDS, +CMGR, +CMGL commands.

9.8.2 Syntax:
Command Syntax: AT+CSDH
COMMAND POSSIBLE RESPONSES
AT+CSDH? +CSDH: 0
Note: Current value OK
Note: Do not show header values

9.9 New message indication +CNMI

9.9.1 Description:
This command selects the procedure for message reception from the network.

9.9.2 Syntax:
Command Syntax: AT+CNMI=<mode>,<mt>,<bm>,<ds>,<bfr>
COMMAND POSSIBLE RESPONSES
AT+CNMI=2,1,0,0,0 OK
Note: <mt>=1
AT+CMTI : “SM”,1
Note: message received
AT+CNMI=2,2,0,0,0 OK
Note: <mt>=2
+CMT : “123456”,”98/10/01,12 :30 00+00”,129,4
,32,240, “15379”,129,5<CR><LF>
message received
Note: message received
AT+CNMI=2,0,0,1,0 OK
Note: <ds>=1
AT+CMGS=”+33146290800”<CR> +CMGS : 7
Message to send <ctrl-Z> OK
Note: Send a message in text mode Note: Successful transmission
+CDS : 2, 116, ”+33146290800”, 145, “98/10/01,12 :30
:07+04”, “98/10/01 12 :30 :08+04”, 0
Note: message was correctly delivered

61
9.9.3 Defined values:
<mode>
controls the processing of unsolicited result codes
Only <mode>=2 is supported.
Any other value for <mode> (0,1 or 3) is accepted (return code will be OK), but the
processing of unsolicited result codes will be the same as with<mode>=2.
<mode>
0: Buffer unsolicited result codes in the TA. If TA result code buffer is full, indications can
be buffered in some other place or the oldest indications may be discarded and
replaced with the new received indications
1: Discard indication and reject new received message unsolicited result codes when TA-
TE link is reserved. Otherwise forward them directly to the TE
2: Buffer unsolicited result codes in the TA when TA-TE link is reserved and flush them to
the TE after reservation. Otherwise forward them directly to the TE
3: Forward unsolicited result codes directly to the TE. TA-TE link specific inband used to
embed result codes and data when TA is in on-line data mode

<mt>
sets the result code indication routing for SMS-DELIVERs. Default is 0.
<mt>
0: No SMS-DELIVER indications are routed.
1: SMS-DELIVERs are routed using unsolicited code : +CMTI: “SM”,<index>
2: SMS-DELIVERs (except class 2 messages) are routed using unsolicited code : +CMT :
[<alpha>,] <length> <CR> <LF> <pdu> (PDU mode) or +CMT : <oa>,[<alpha>,] <scts>
[,<tooa>, <fo>, <pid>, <dcs>, <sca>, <tosca>, <length>] <CR><LF><data> (text mode)
3: Class 3 SMS-DELIVERS are routed directly using code in <mt>=2 ; Message of other
classes result in indication <mt>=1

<bm>
set the rules for storing received CBMs (Cell Broadcast Message) types depend on its
coding scheme, the setting of Select CBM Types (+CSCB command) and <bm>. Default is 0.
<bm>
0: No CBM indications are routed to the TE. The CBMs are stored.
1: The CBM is stored and an indication of the memory location is routed to the customer
application using unsolicited result code: +CBMI: “BM”, <index>
2: New CBMs are routed directly to the TE using unsolicited result code. +CBM :
<length><CR><LF><pdu> (PDU mode) or +CBM
:<sn>,<mid>,<dcs>,<page>,<pages>(Text mode) <CR><LF> <data>
3: Class 3 CBMs : as <bm>=2. Other classes CBMs : as <bm>=1.

62
<ds>
for SMS-STATUS-REPORTs. Default is 0.
<ds>
0: No SMS-STATUS-REPORTs are routed.
1: SMS-STATUS-REPORTs are routed using unsolicited code : +CDS : <length> <CR> <LF>
<pdu> (PDU mode) or +CDS : <fo>,<mr>, [<ra>] , [<tora>], <scts>,<dt>,<st> (Text mode)
2: SMS-STATUS-REPORTs are stored and routed using the unsolicited result code :
+CDSI: “SR”,<index>

<bfr>
Default is 0.
<bfr>
0: TA buffer of unsolicited result codes defined within this command is flushed to the TE
when <mode> 1…3 is entered (OK response shall be given before flushing the codes)
1: TA buffer of unsolicited result codes defined within this command is cleared when
<mode> 1…3 is entered.

9.10 Read message +CMGR

9.10.1 Description:
This command allows the application to read stored messages. The messages are read
from the memory selected by +CPMS command.

9.10.2 Syntax:
Command Syntax: AT+CMGR=<index>
Response syntax for text mode:
+CMGR :<stat>,<oa>,[<alpha>,] <scts> [,<tooa>,<fo>, <pid>,<dcs>,
<sca>, <tosca>,<length>] <CR><LF> <data> (for SMS-DELIVER only)
+CMGR : <stat>,<da>,[<alpha>,] [,<toda>,<fo>,<pid>,<dcs>, [<vp>],
<sca>, <tosca>,<length>]<CR><LF> <data> (for SMS-SUBMIT only)
+CMGR : <stat>,<fo>,<mr>,[<ra>],[<tora>],<scts>,<dt>,<st>
(for SMS-STATUS-REPORT only)
Response syntax for PDU mode :
+CMGR: <stat>, [<alpha>] ,<length> <CR><LF> <pdu>

63
A message read with status “REC UNREAD” will be updated in memory with the status
“REC READ”.
NOTE: the <stat> parameter for SMS Status Reports is always “READ”.

Example :
COMMAND POSSIBLE RESPONSES
AT+CMTI: “SM”,1
Note: New message received
AT+CMGR=1 +CMGR: “REC UNREAD”,”0146290800”,
”98/10/01,18 :22 :11+00”,<CR><LF>
ABCdefGHI
OK
Note: Read the message
AT+CMGR=1 +CMGR: “REC UNREAD”,”0146290800”,
”98/10/01,18 :22 :11+00”,<CR><LF>
ABCdefGHI
OK
Note: Read the message again Note: Message is read now
AT+CMGR=2 +CMS ERROR: 321
Note: Read at a wrong index Note: Error : invalid index
AT+CMGF=0 ;+CMGR=1 +CMGR: 2,,<length> <CR><LF><pdu>
OK
Note: In PDU mode Note: Message is stored but unsent, no <alpha>field
AT+CMGF=1;+CPMS=”SR”;+CNMI=,,,2 OK
Reset to text mode, set read memory to “SR”,
and allow storage of further SMS Status
Report into “SR” memory
AT+CMSS=3 +CMSS: 160
Send an SMS previously stored OK
+CDSI: “SR”,1
New SMS Status Report stored in “SR” memory at index 1
AT+CMGR=1 +CMGR: "READ",6,160,
Read the SMS Status Report "+33612345678",129,"01/05/31,15:15:09+00",
"01/05/31,15:15:09+00",0
OK

64
9.11 List message +CMGL

9.11.1 Description:
This command allows the application to read stored messages, by indicating the type of
the message to read. The messages are read from the memory selected by the +CPMS
command.

9.11.2 Syntax:
Command Syntax: AT+CMGL=<stat>
Response syntax for text mode:
+CMGL : <index>,<stat>,<da/oa>[,<alpha>], [<scts>, <tooa/toda>,
<length>] <CR><LF><data> (for SMS-DELIVER and SMS-SUBMIT,
may be followed by other <CR><LF>+CMGL:<index>…)
+CMGL : <index>,<stat>,<fo>,<mr>,[<ra>],[<tora>],<scts>,<dt>,<st>
(for SMS-STATUS-REPORT only, may be followed by other
<CR><LF>+CMGL:<index>…)

Response syntax for PDU mode :


+CMGL : <index>,<stat>, [<alpha>], <length> <CR><LF> <pdu>
(for SMS-DELIVER, SMS-SUBMIT and SMS-STATUS-REPORT,
may be followed by other <CR><LF>+CMGL:<index>…)
COMMAND POSSIBLE RESPONSES
AT+CMGL=“REC UNREAD” +CMGL: 1,”REC UNREAD”,”0146290800”,
<CR><LF> Unread message !
+CMGL: 3,”REC UNREAD”, “46290800”, <CR><LF>
Another message unread!
OK
Note: List unread messages in text mode Note: 2 messages are unread, these messages will then
have their status changed to “REC READ” (+CSDH:0)
AT+CMGL=”REC READ” +CMGL: 2,”REC READ”,”0146290800”,
<CR><LF>
Keep cool
Note: List read messages in text mode OK
AT+CMGL=”STO SENT” OK
Note: List stored and sent messages in text mode Note: No message found
AT+CMGL=1 +CMGL: 1,1,,26
<CR><LF>
07913366003000F3040B913366920547F4001300119041
2530400741AA8E5A9C5201
Note: List read messages in PDU mode OK

65
9.11.3 Defined values:
<stat> possible values (status of messages in memory):

Text mode PDU mode Status of messages


possible values possible values in memory
“REC UNREAD” 0 received unread messages
“REC READ” 1 received read messages
“STO UNSENT” 2 stored unsent messages
“STO SENT” 3 stored sent messages
“ALL” 4 all messages

NOTE: For SMS Status Reports, only “ALL” / 4 and “READ” / 1 values of the <stat> parameter will list
messages ; other values will only return OK.

9.12 Send message +CMGS

9.12.1 Description:
The <address> field is the address of the terminal to which the message is sent. To send
the message, simply type, <ctrl-Z> character (ASCII 26). The text can contain all existing
characters except <ctrl-Z> and <ESC> (ASCII 27).
This command can be aborted using the <ESC> character when entering text.
In PDU mode, only hexadecimal characters are used (‘0’…’9’,’A’…’F’).

9.12.2 Syntax:
Command syntax in text mode:
AT+CMGS= <da> [ ,<toda> ] <CR>
text is entered <ctrl-Z / ESC >
Command syntax in PDU mode :
AT+CMGS= <length> <CR>
PDU is entered <ctrl-Z / ESC >

COMMAND POSSIBLE RESPONSES


AT+CMGS=”+33146290800”<CR> +CMGS: <mr>
Please call me soon, Fred. <ctrl-Z> OK
Note: Send a message in text mode Note: Successful transmission
AT+CMGS=<length><CR><pdu><ctrl-Z> +CMGS: <mr>
OK
Note: Send a message in PDU mode Note: Successful transmission

The message reference, <mr>, which is returned to the application is allocated by the
product. This number begins with 0 and is incremented by one for each outgoing message
(successful and failure cases); it is cyclic on one byte (0 follows 255).
NOTE: this number is not a storage number – outgoing messages are not stored.

66
9.13 Write Message to Memory +CMGW

9.13.1 Description:
This command stores a message in memory (either SMS-SUBMIT or SMS-DELIVERS).
The memory location <index> is returned (no choice possible as with phonebooks
+CPBW).
Text or PDU is entered as described for the Send Message +CMGS command.

9.13.2 Syntax:
Command syntax in text mode : (<index> is returned in both cases)
AT+CMGW= <oa/da> [,<tooa/toda> [,<stat> ] ] <CR>
enter text <ctrl-Z / ESC>
Command syntax in PDU mode :
AT+CMGW= <length> [,<stat>] <CR>
give PDU <ctrl-Z / ESC>
Response syntax: +CMGW: <index> or +CMS ERROR: <err> if writing fails
COMMAND POSSIBLE RESPONSES
AT+CMGW=”+33146290800”<CR> +CMGW: 4
Hello how are you ?<ctrl-Z> OK
Note: Write a message in text mode Note: Message stored in index 4
AT+CMGW=<length><CR><pdu><ctrl-Z> +CMGW: <index>
OK
Note: Write a message in PDU mode Note: Message stored in <index>

9.13.3 Defined values:


Parameter Definition:
<oa/da> : Originating or Destination Address Value in string format.
<tooa/toda> : Type of Originating / Destination Address.
<stat> : Integer type in PDU mode (default 2 for +CMGW), or string type in text mode
(default “STO UNSENT” for +CMGW). Indicates the status of message in memory. If <stat>
is omitted, the stored message is considered as a message to send.
<stat>
0: “REC UNREAD”
1: “REC READ”
2: “STO UNSENT”
3: “STO SENT”
<length>
Length of the actual data unit in octets

67
9.14 Send Message From Storage +CMSS

9.14.1 Description:
This command sends a message stored at location value <index>.

9.14.2 Syntax:
Command syntax: AT+CMSS=<index>[,<da> [,<toda>] ]
Response syntax: +CMSS : <mr> or +CMS ERROR: <err> if sending fails
If a new recipient address <da> is given, it will be used instead of the one stored with the
message
COMMAND POSSIBLE RESPONSES
AT+CMGW=0660123456<CR> +CMGW : 5
Today is my birthday OK
Note: Note:Message stored with index 5
AT+CMSS=5, 0680654321 AT+CMSS :<mr>
OK
Note: Send the message 5 to a different destination number Note: Successful transmission
AT+CMSS=5, 0680654321 +CMSS :<mr>
OK
Note: Send the message 5 to a different Note: Successful transmission
destination number

9.15 Set Text Mode Parameters +CSMP

9.15.1 Description:
This command is used to select a value for <vp>, <pid>, and <dcs>.

9.15.2 Syntax:
Command Syntax: AT+CSMP=<fo>, <vp>, <pid>,<dcs>
COMMAND POSSIBLE RESPONSES
AT+CSMP? +CSMP: 0,0,0,0
OK
Note: current values Note: No validity period
<dcs>= PCCP437 alphabet (8 bits ‡ 7 bits)
AT+CMPS=17,23,64,244 OK
Note: <vp> = 23 (2 hours, relative format) Note: Command correct
<dcs> = GSM 8 bits alphabet

68
9.15.3 Defined values:
The <fo> byte comprises 6 different fields :

b7 b6 b5 b4 b3 b2 b1 b0
RP UDHI SRR VPF RD MTI

RP: Reply Path, not used in text mode.


UDHI: User Data Header Information, b6=1 if the beginning of the User Data field contains
a Header in addition to the short message. This option is not supported in +CSMP
command, but can be used in PDU mode (+CMGS).
SRR: Status Report Request, b5=1 if a status report is requested. This mode is supported.
VPF: Validity Period Format
b4=0 & b3=0 -> <vp> field is not present
b4=1 & b3=0 -> <vp> field is present in relative format
Others formats (absolute & enhanced) are not supported.
RD: Reject Duplicates, b2=1 to instruct the SC to reject an SMS-SUBMIT for an SM still
held in the SC which has the same <mr> and the same <da> as the previously
submitted SM from the same <oa>.
MTI: Message Type Indicator
b1=0 & b0=0 -> SMS-DELIVER (in the direction SC to MS)
b1=0 & b0=1 -> SMS-SUBMIT (in the direction MS to SC)

In text mode <vp> is only coded in “relative” format. The default value is 167 (24 hours).
This means that one octet can describe different values:

VP value Validity period value


0 to 143 (VP + 1) x 5 minutes (up to 12 hours)
144 to 167 12 hours + ( (VP – 143) x 30 minutes )
168 to 196 (VP – 166) x 1 day
197 to 255 (VP – 192) x 1 week

<pid> is used to indicate the higher layer protocol being used or indicates interworking
with a certain type of telematic device. For example, 0x22 is for group 3 telefax, 0x24 is for
voice telephone, 0x25 is for ERMES.
<dcs> is used to determine the way the information is encoded. Compressed text is not
supported. Only GSM default alphabet, 8 bit data and UCS2 alphabet are supported.

69
9.16 Delete message +CMGD

9.16.1 Description:
This command is used to delete one or several messages from preferred message storage
(“BM” SMS CB ‘RAM storage’, “SM” SMSPP storage ‘SIM storage’ or “SR” SMS Status-
Report storage).

9.16.2 Syntax:
Command Syntax: AT+CMGD=<Index> [,<DelFalg>]
COMMAND POSSIBLE RESPONSES
+CMTI:”SM”,3
Note: New message received
AT+CMGR=3 +CMGR: “REC UNREAD”,”0146290800”,
“98/10/01,18 :19 :20+00” <CR><LF>
Message received!
Note: Read it Note: Unread message received from 0146290800 on the
01/10/1998 at 18H19m 20s
AT+CMGD=3 OK
Note: Delete it Note: Message deleted
AT+CMGD=1,0 OK
Note: The message from the preferred message storage at
the location 1 is deleted
AT+CMGD=1,1 OK
Note: All READ messages from the preferred message
storage are deleted
AT+CMGD=1,2 OK
Note: All READ messages and SENT mobile originated
messages are deleted
AT+CMGD=1,3 OK
Note: All READ, SENT and UNSENT messages are deleted
AT+CMGD=1,4 OK
Note: All messages are deleted

70
9.16.3 Defines values:
<index>
1-20: When the preferred message storage is “BM”
Integer type values in the range of location numbers of SIM Message memory when the
preferred message storage is “SM” or “SR”.
<DelFlag>
0: Delete message at location <index>.
1: Delete All READ messages
2: Delete All READ and SENT messages
3: Delete All READ, SENT and UNSENT messages
4: Delete All messages.

NOTE: when the preferred message storage is “SR”, as SMS status reports are assumed to have a
“READ” status, if <DelFlag> is greater than 0, all SMS status reports will be deleted.

9.17 Service center address +CSCA

9.17.1 Description:
This command is used to indicate which service center the message must be sent to.
The product has no default value for this address. If the application tries to send a
message without having indicated the service center address, an error will be generated.
Therefore, the application must indicate the SC address when initialising the SMS. This
address is then permanently valid. The application may change it if necessary.

9.17.2 Syntax:
Command Syntax: AT+CSCA
COMMAND POSSIBLE RESPONSES
AT+CMGS= “+33146290800”<CR> +CMS ERROR: 330
Hello, how are you?<ctrl-Z>
Note: Send a message Note: service center unknown
AT+CSCA=”0696741234” OK
Note: Service center initialization Note:
AT+CMGS=”+33146290800”<CR> +CMGS: 1
Happy Birthday ! <ctrl-Z> OK
Note: Note: Successful transmission

71
9.18 Select Cell Broadcast Message Types +CSCB

9.18.1 Description:
This command selects which types of CBMs are to be received by the ME, This command
is allowed in both PDU and text modes.

9.18.2 Syntax:
Command Syntax: AT+CSCB= <mode>, [ <mids>, [ <dcss> ] ]
The <bm> parameter of +CNMI command controls the message indication.
Test read command (AT+CSCB ?) is not supported.
The activation of CBM reception (<mode>=0) can select only specific Message Identifiers
(list in <mids>) for specific Languages (list in <dcss>), but the deactivation stops any
reception of CBMs (only AT+CSCB=1 is allowed)
Message Identifiers (<mids> parameter) indicates which type of message identifiers the
ME should listen to.
Supported languages (<dcss> parameter) are : 0 for German, 1 for English, 2 for Italian, 3
for French, 4 for Spanish, 5 for Dutch, 6 for Swedish, 7 for Danish, 8 for Portuguese, 9 for
Finnish, 10 for Norwegian, 11 for Greek, 12 for Turkish, 13 for Hungarian, 14 for Polish and
32 for Czech.
COMMAND POSSIBLE RESPONSES
AT+CSCB=0,”15-17,50,86”,”” OK
Note: Accept SMS-CB types, 15,16,17,50 and Note: CBMs can be received
86 in any language
+CBM : 10<CR><LF> AT+CSCB=1
00112233445566778899
Note: CBM length of a received Cell Broadcast Note: Deactivate the reception of CBMs
message (SMS-CB), CBM bytes in PDU mode
AOK
Note: CBM reception is completely stopped

72
9.19 Cell Broadcast Message Identifiers +WCBM

9.19.1 Description:
This specific command is used to read the EF-CBMI SIM file.
Remark: The EF-CBMI file is not used with the +CSCB command.
The application should read this file (using AT+WCBM ?) and combine the Message
Identifiers with those required by the application.

9.19.2 Syntax:
Command Syntax: AT+WCBM= <mids>
COMMAND POSSIBLE RESPONSES
AT+WCBM=”10,100,1000,10000” OK
Note: Write 4 messages identifiers in EF-CBMI Note: CBMIs are stored in EF-CBMI
AT+WCBM? +WCBM=”10,100,1000,100000”
Note: Read the CBMIs in EF-CBMI Note: 4 CBMIs are stored in EF-CBMI

9.20 Message status modification +WMSC

9.20.1 Syntax:
Command Syntax: AT+WMSC= <loc>, <status>
<loc>
location number of the stored message (integer)
<status>
new status to be stored, as for +CMGL command :
PDU Mode Text Mode
0 “REC UNREAD”
1 “REC READ”
2 “STO UNSENT”
3 “STO SENT”

Possible responses:
OK if the location is valid
+CMS ERROR: 321 if <loc> is invalid or free
+CMS ERROR: 302 if the new <status> and the previous one are incompatible (1)

NOTE 1: The accepted status changes are from READ to NOT READ and vice versa, and from SENT to
NOT SENT and vice versa.
If all the parameters are correct, the product overwrites the whole SMS in SIM. Only the first byte
(Status byte) is changed.

73
9.21 Message overwriting +WMGO

9.21.1 Description:
The +CMGW command writes an SMS to the first location available. To write an SMS to a
specified location, the +WMGO specific command forces the product to write an SMS
(with the +CMGW command) to the location specified with +WMGO, but for just one
+CMGW command.

9.21.2 Syntax:
Command Syntax: AT+WMGO= <loc>
<loc> location number of the SIM record to write or overwrite

Possible responses:
OK if <loc> is a valid SMS location, for AT+WMGO=? and for AT+WMGO?
+CMS ERROR: 321 if <loc> is out of the SIM capacity range.
+WMGO: <loc> for AT+WMGO?

On the next AT+CMGW command, the record number used will be the one specified by
the AT+WMGO command. The location is forgotten and, in order to perform a second
overwrite, +WMGO has to be used again.
If the external application specifies a free location, and if an incoming message is received
before the AT+CMGW command, the product may store the incoming message at a
location available. This could be the one specified by +WMGO (the product does not
prevent from this). If the user then issues an AT+CMGW command without changing the
AT+WMGO location, the new message will be overwritten!
NOTE: that this location number is not kept over a software reset.

9.22 Unchange SMS Status +WUSS

9.22.1 Description:
The +WUSS command allows to keep the SMS Status to UNREAD after +CMGR or
+CMGL.

9.22.2 Syntax:
Command Syntax: AT+WUSS = <mode>
<mode>
0: The SMS Status will not change.
1: The SMS Status will change.

Possible responses:
OK

74
10 Supplementary Services commands

10.1 Call forwarding +CCFC

10.1.1 Description:
This commands allows control of the "call forwarding" supplementary service.

10.1.2 Syntax:
Command Syntax: AT+CCFC= <reason>, <mode> [, <number> [,<type> [,<class> [,
<subaddr> [, <satype> [,<time> ] ] ] ] ] ]
Response syntax: +CCFC: <status>, <class1> [, <number>, <type> [,<subaddr>, <satype> [,
<time> ] ] ] [ <CR><LF>+CCFC: <status>, <class2> [, <number>,
<type> [,<subaddr>, <satype> [,<time> ] ] ] [ … ] ]
COMMAND POSSIBLE RESPONSES
AT+CCFC=0,3,”0146290800” OK
Note: Register to an unconditional call forwarding
Note: Command valid
AT+CCFC=0,2 +CCFC:1,1,”0146290800”,129
Note: Interrogate unconditional call forwarding
Note: Call forwarding active for voice
<CR><LF>+CCFC:1,2,”0146290802”,129
Note: Call forwarding active for data
<CR><LF>+CCFC:1,4,”0146290804”,129
OK
Note: Call forwarding active for fax
AT+CCFC=0,4 OK
Note: Erase unconditional call forwarding Note: Command valid
+CCFC responses are not sorted by <class> parameter, but only by the order of net-work
response.

75
10.1.3 Defined values:
<reason>
0: Unconditional
1: Mobile busy
2: No reply
3: Not reachable
4: All call forwarding
5: All conditional call forwarding

<mode>
0: Disable
1: Enable
2: Interrogate
3: Registration
4: Erasure

<class>
1: Voice
2: Data
3: Fax
4: Short Messages
5: All classes

NOTE: The combination of different classes is not supported, it will only result in the activation /
deactivation / status request of all classes (7).

In the case where the FDN phonebook is activated, the registration is restricted to the
phone numbers written in the FDN.

<subaddr> not managed


<satype> not managed
<time> For <reason> = 2 (No reply), 4 (all call forwarding) and 5 (all conditional call forwarding),
time to wait (1 to 30) in seconds before call is forwarded. Default value is 20.

10.2 Call barring +CLCK

10.2.1 Description:
This command allows control of the call barring supplementary service.
Locking, unlocking or querying the status of call barring is possible for all classes or for a
specific class.

76
10.2.2 Syntax:
Command Syntax: AT+CLCK= <fac>, <mode> [, <password> [, <class> ] ]
Response Syntax: (for <mode>=2 and command successful)
+CLCK: <status> [, <class1> [ <CR><LF>+CLCK: <status>, <class2> [… ] ]
COMMAND POSSIBLE RESPONSES
AT+CLCK=”AO”,1,1234 OK
Note: Note: Command valid
AT+CLCK=”AO”,0,5555 +CME ERROR: 16
Note: Note: Wrong password
AT+CLCK=”AO”,0,1234 OK
Note: Note: Command valid

<fac>
“AO”, “OI”, “OX” : barring for outgoing calls
“AI”, “IR” : barring for incoming calls
“AG”, “AC”,”AB” : for all calls barring (<mode>=0 only)

<mode>
0: Unlocks the facility
1: Locks the facility
2: Query status

<class>
see description for +CLCK command (Facility lock) or +CCFC (Call forwarding).

A combination of different classes is not supported. It will only result in the activation /
deactivation / status request for all classes (7).
The password code is over 4 digits maximum.

10.3 Modify SS password +CPWD

10.3.1 Description:
This command is used by the application to change the supplementary service password.

10.3.2 Syntax:
Command Syntax: AT+CPWD=<fac>,<OldPassword>, <NewPassword>
for <fac> see +CLCK command with only “P2” facility added (SIM PIN2).
COMMAND POSSIBLE RESPONSES
AT+CPWD=”AO”,1234,5555 OK
Note: Change Call Barring password Note: Password changed
AT+CPWD=”AO”,1234,5555 +CME ERROR: 16
Note: Change password Note: Wrong password
AT+CPWD=”AO”,5555,1234 OK
Note: Change password Note: Password changed

Whatever the facility, the change of password applies to all call barring.

77
10.4 Call waiting +CCWA

10.4.1 Description:
This command allows control of the call waiting supplementary service.
The product will send a +CCWA unsolicited result code when the call waiting service is
enabled.

10.4.2 Syntax:
Command Syntax: AT+CCWA=<n>, [ <mode> [, <class> ] ]
Response Syntax: (for <mode>=2 and command successful)
+CCWA: <status> [, <class1> [ <CR><LF>+CCWA: <status>, <class2>
[…]]
Unsolicited result: +CCWA: <number>, <type>, <class> [ ,<alpha>]
(when waiting service is enabled)
COMMAND POSSIBLE RESPONSES
AT+CCWA=1,1,1 OK
Note: Enable call waiting for voice calls Note: Command valid
AT+CCWA=1,2 +CCWA:1,1
OK
Note: Interrogate call waiting Note: Call waiting active for voice calls
+CCWA:”0146290800”,145,1,”FREDDY”
or Note:
+CCWA:”0146290800”,145,1,”8023459678FFFF”
(UCS2 format)
Note: Number and name of the waiting voice call
AT+CCWA=1,0,7 OK
Note: Erase call waiting Note: Command valid
+CCWA:,,1
Note: voice call waiting (no number)

10.4.3 Defined values:


<n>
result code presentation status in the TA
<n>
0: Disable
1: Enable

<mode>
0: Disable
1: Enable
2: Query status

78
<class>
1: Voice
2: Data
3: Fax Short
4: Messages
5: All classes

A combination of different classes is not supported. It will only result in the activation /
deactivation / status request for all classes (7).

<alpha>
optional string type alphanumeric representation of <number> corresponding to the entry
found in the ADN or FDN phonebook.

10.5 Calling line identification restriction +CLIR

10.5.1 Description:
This command allows control of the calling line identification restriction supplementary
service.

10.5.2 Syntax:
Command Syntax: AT+CLIR=<n>
Response Syntax: +CLIR :<n>,<m> (for AT+CLIR ?)
COMMAND POSSIBLE RESPONSES
AT+CLIR=2 OK
Note: Note: Command valid
AT+CLIR ? +CLIR :<n>,<m>
OK
Note: Ask for current functionality Note: <n> and <m> as defined here-below

10.5.3 Defined values:


<n>
sets the line ID restriction for outgoing calls
<n>
0: Presentation indicator is used according to the subscription of the CLIR service
1: CLIR invocation
2: CLIR suppression

<m>
shows the subscriber CLIR status in the network
<m>
0: CLIR not provisioned
1: CLIR provisioned in permanent mode
2: Unknown (no network…)
3: CLIR temporary mode presentation restricted
4: CLIR temporary mode presentation allowed

79
10.6 Calling line identification presentation +CLIP

10.6.1 Description:
This command allows control of the calling line identification presentation supple-mentary
service. When presentation of the CLI (Calling Line Identification) is enabled (and calling
subscriber allows), +CLIP response is returned after every RING (or +CRING) result code.

10.6.2 Syntax:
Command Syntax: AT+CLIP=<n>
Response Syntax: +CLIP: <n>,<m for AT+CLIP?
+CLIP: <number>, <type>[ ,<subaddr>, <satype>, <alpha> ] for an
incoming call, after each RING or +CRING indication
COMMAND POSSIBLE RESPONSES
AT+CLIP=1 OK
Note: Enable CLIP Note: CLIP is enabled
AT+CLIP? +CLIP:<n>,<m>
OK
Note: Ask for current functionality Note: <n> and <m> defined as below
RING
Note: Incoming call
+CLIP: “0146290800”,129,1,,,”FRED”
or
+CLIP: “0146290800”,129,1,,,”8000204212FFFF”
(UCS2 format)
Note: Incoming call with number and name presentation
AT+CLIP=0 OK
Note: Disable CLIP presentation Note: Command valid

10.6.3 Defined values:


<n>
parameter sets/shows the result code presentation in the TA
<n>
0: Disable
1: Enable

<m>
parameter shows the subscriber CLIP service status in the network
<m>
0: CLIP not provisioned
1: CLIP provisioned
2: Unknown (no network…)

10.7 Connected line identification presentation +COLP

10.7.1 Description:
This command allows control of the connected line identification presentation
supplementary service - useful for call forwarding of the connected line.

80
10.7.2 Syntax:
Command syntax: AT+COLP=<n>
Response syntax: +COLP: <n>,<m> for AT+COLP?
+COLP: <number>,<type> [ ,<subaddr>, <satype>, <alpha> ]
after ATD command, before OK or CONNECT <speed>
COMMAND POSSIBLE RESPONSES
AT+COLP=1 OK
Note: Activate COLP Note: Command valid
AT+COLP? +COLP:1,1
OK
Note: Ask for current functionality Note: COLP is enabled and provisioned
ATD146290928; +COLP:”0146290928”,129,,,”JOE”
or
+COLP:“0146290800”,129,1,,,”8000204212FFFF”
(UCS2 format)
OK
Note: Outgoing call Note: Connected outgoing line number and name presentation
AT+COLP=0 OK
Note: Deactivate COLP Note: Command valid

10.7.3 Defined values:


<n>
parameter sets/shows the result code presentation status in the TA
<n>
0: Disable
1: Enable

<m>
parameter shows the subscriber COLP service status in the network
<m>
0: COLP not provisioned
1: COLP provisioned
2: Unknown (no network)

81
10.8 Advice of charge +CAOC

10.8.1 Description:
This refers to the Advice of Charge supplementary service (GSM 02.24 and GSM 02.86)
which enables the subscriber to obtain information on call cost. With <mode>=0, the
command returns the current call meter value (CCM) from the ME.
If AOC is supported, the command can also enable unsolicited event reporting on CCM
information.
The unsolicited result code +CCCM: <ccm> is sent when the CCM value changes.
Deactivation of unsolicited event reporting is performed with the same command.
If AOC is supported, the Read command indicates whether unsolicited reporting is
activated or not.

10.8.2 Syntax:
Command Syntax: AT+CAOC= <mode>
COMMAND POSSIBLE RESPONSES
AT+CAOC=0 +CAOC: “000A08”
OK
Note: Query CCM value Note: Display Current Call Meter value (CCM=2568)
AT+CAOC=1 OK
Note: Deactivate unsolicited report of CCM value Note: CCM report deactivated
AT+CAOC=2 OK
Note: Activate unsolicited report of CCM value Note: CCM report activated
AT+CAOC ? +CAOC :<mode>
OK
Note: Request mode Note: Display unsolicited report mode (1 or 2)
AT+CAOC=? +CAOC : (0-2)
OK
Note: Request supported modes Note: 0,1,2 modes supported

10.8.3 Defined values:


<mode>
0: query CCM value
1: deactivate the unsolicited reporting of CCM value
2: activate the unsolicited reporting of CCM value

<ccm>
string type; three bytes of the current call meter value in hexadecimal format (e.g.
“00001E” corresponds to the decimal value 30); value is in home units and bytes are
coded in a similar way as the ACMmax value in SIM

82
10.9 Accumulated call meter +CACM

10.9.1 Description:
This command resets the Advice of Charge for accumulated call meter value in SIM file
EFACM. The ACM contains the total number of home units for both the current and
preceding calls. SIM PIN2 is required to reset the value. If setting fails in an ME error,
+CME ERROR: <err> is returned.
The Read command returns the current value of the ACM.
The ACM value (entered or displayed) is in hexadecimal format with 6 digits.

10.9.2 Syntax:
Command Syntax: AT+CACM
COMMAND POSSIBLE RESPONSES
AT+CACM? +CACM: “000400”
OK
Note: Request ACM value Note: Display ACM value (ACM=1024)
AT+CACM= 1234 OK
Note: Request ACM reset, real PIN2 is “1234” Note: ACM value is reset
AT+CACM= 0000 +CME ERROR : 16
Note: Request ACM reset with wrong PIN2 value Note: Incorrect password
AT+CACM ? +CACM: “000000”
OK
Note: Request ACM value Note: Display ACM value (ACM = 0)

83
10.10 Accumulated call meter maximum +CAMM

10.10.1 Description:
The set command sets the Advice of Charge related to accumulated call meter maximum
value in SIM file EFACMmax. ACMmax contains the maximum number of home units the
subscriber is allowed to consume. When ACM (see +CACM) reaches ACMmax, calls are
prohibited. SIM PIN2 is required to set the value. If setting fails in an ME error, +CME
ERROR: <err> is returned.
The Read command returns the current value of ACMmax.
The ACMmax value (entered or displayed) is in hexadecimal format with 6 digits.

10.10.2 Syntax:
Command Syntax: AT+CAMM
COMMAND POSSIBLE RESPONSES
AT+CAMM=”000400”,1234 OK
Note: Request ACMmax update, PIN2 is “1234” Note: ACMmax updated to 1024
AT+CAMM=”000400”,0000 +CME ERROR : 16
Note: Request ACMmax update, PIN2 is “1234” Note: Incorrect password
AT+CAMM ? +CAMM : “000400”
OK
Note: Request ACMmax value Note: ACMmax = 1024

10.11 Price per unit and currency table +CPUC

10.11.1 Description:
The set command sets the parameters for Advice of Charge related to price per unit and
the currency table in SIM file EFPUCT. PUCT information can be used to convert the home
units (as used in +CAOC, +CACM and +CAMM) into currency units. SIM PIN2 is required to
set the parameters. If setting fails in an ME error, +CME ERROR: <err> is returned.

10.11.2 Syntax:
Command Syntax: AT+CPUC
COMMAND POSSIBLE RESPONSES
AT+CPUC=”FFR”,”0.82”,1234 OK
Note: Request Currency and Price per unit update Note:
AT+CPUC=”FFR”,”0.82”,1111 + CME ERROR : 16
Note: Request Currency and PPU update (wrong PIN2) Note: Incorrect password
AT+CPUC? +CPUC:”FFR”,”0.82”
OK
Note: Currency= “FFR”
Note: Request Currency and Price Price per unit= “0.82”

84
10.12 Call related supplementary services +CHLD

10.12.1 Description:
This command is used to manage call hold and multiparty conversation (conference call).
Calls can be put on hold, recovered, released or added to a conversation.

10.12.2 Syntax:
Command syntax: AT+CHLD= < n >
Response syntax: +CHLD: (0-4, 11-17, 21-27) for AT+CHLD=?

10.12.3 Defined values:


<n>
0: Release all held calls or set User Determined User Busy (UDUB) for a waiting call.
1: Release all active calls (if any exist) and accepts the other (held or waiting) call.
1X: Release a specific call X (active, held or waiting)
2: Place all active calls (if any exist) on hold and accepts the other (held or waiting) call.
2X: Place all active calls on hold except call X with which communication is supported.
3: Adds a held call to the conversation.
4: Connects the two calls and disconnects the subscriber from both calls (Explicit Call
Transfer).

85
10.13 List current calls +CLCC

10.13.1 Description:
This command is used to return a list of current calls.

10.13.2 Syntax:
Command Syntax: AT+CLCC
Response syntax: OK if no calls are available
+CLCC : <id1>, <dir>, <stat>, <mode>, <mpty> [ ,<number>, <type>
[<alpha> ] ][ <CR><LF>
+CLCC: <id2>, <dir>, <stat>, <mode>, <mpty> [ ,<number>, <type>
[<alpha> ] ] [. . . ] ] ]

10.13.3 Defined values:


<idx>
integer type, call identification as described in GSM 02.30

<dir>
0: mobile originated (MO) call
1: mobile terminated (MT) call

<stat> (state of the call):


0: active
1: held
2: dialling (MO call)
3: alerting (MO call)
4: incoming (MT call)
5: waiting (MT call)

<mode>(teleservice):
0: voice
1: data
2: fax
9: unknown

<mpty>
0: call is not one of multiparty (conference) call parties
1: call is one of multiparty (conference) call parties

<number> : string type phone number in format specified by <type>

<type> : type of address octet in integer format

<alpha> : optional string type alphanumeric representation of <number>


corresponding to the entry found in phonebook. (for UCS2 format see commands
examples +CLIP, +CCWA or +COLP)

86
10.14 Supplementary service notifications +CSSN

10.14.1 Description:
This command refers to supplementary service related network initiated notifications.
When <n>=1 and a supplementary service notification is received after a mobile originated
call setup, intermediate result code +CSSI:<code1>[,<index>] is sent before any other MO
call setup result codes.
When <m>=1 and a supplementary service notification is received during a call,
unsolicited result code +CSSU:<code2>[,<index>[,<number>,<type>]] is sent.

10.14.2 Syntax:
Command syntax: AT+CSSN= <n>, <m>
Response syntax: +CSSN: <n>, <m> for AT+CSSN?
+CSSN: (0-1), (0-1) for AT+CSSN=?

10.14.3 Defined values:


<n> (parameter sets/shows the +CSSI result code presentation status):
0: disable
1: enable

<m> (parameter sets/shows the +CSSU result code presentation status):


0: disable
1: enable

<code1>
4: closed User Group call, with CUG <index>
5: outgoing calls are barred
6: incoming calls are barred
7: CLIR suppression rejected

<code2>
1: closed User Group call, with CUG <index>
2: call has been put on hold (during a voice call, <number> & <type> fields may be present)
3: call has been retrieved (during a voice call, <number> & <type> fields may be present)
4: multiparty call entered (during a voice call, <number> & <type> fields may be present)
5: call on hold has been released (during a voice call)
7: call is being connected (alerting) with the remote party in alerting state in Explicit Call
Transfer operation (during a voice call)
8: call has been connected with the other remote party in Explicit Call Transfer operation
(during a voice call, <number> & <type> fields may be present)

<index>
Closed User Group index
<number>
String type phone number
<type>
Type of address

87
10.15 Unstructured supplementary service data +CUSD

10.15.1 Description:
The USSD supplementary service is described in GSM 02.90.
It is based on sequences of digits which may be entered by a mobile user with a handset.
A sequence entered is sent to the network which replies with an alphanumerical string, for
display only, or for display plus request for the next sequence.
This command is used to:
❑ enable or disable the CUSD indication sent to the application by the product when
an incoming USSD is received
❑ send and receive USSD strings

10.15.2 Syntax:
Command Syntax: AT+CUSD = <n> [ ,<str> [ <dcs> ] ]

10.15.3 Defined values:


<n>
0: Disable the result code presentation
1: Enable the result code presentation
2: Cancel session (not applicable to read command response)
In case of enabled presentation, a +CUSD (as direct answer to a send USSD) is then
indicated with :
+CUSD: <m> [,<str>,<dcs> ]
<m>
0: no further user action required (network initiated USSD-Notify, or no further
information needed after mobile initiated operation)
1: further user action required (network initiated USSD-Request, or further information
needed after mobile initiated operation)
2: USSD terminated by network
4: Operation not supported

<str> is network string, converted in the selected character set


<dcs> is the data coding scheme received (GSM TS 03.38).

10.15.4 Syntax To send and receive USSD :


Command syntax: AT+CUSD= <n> [,<str> [,<dcs>]]
NOTE: Please, be aware that the send USSD command needs the user to re-enter the <n> parameter !

10.15.5 Defined values To send and receive USSD :


<str> is the USSD string to be sent.
<dcs> the default alphabet and the UCS2 alphabet are supported.
When the product sends a USSD, an OK response is first returned, the intermediate
+CUSD indication comes subsequently. In case of error, a +CUSD: 4 indication is returned.

88
10.16 Closed user group +CCUG

10.16.1 Description:
The Closed User Group Supplementary Service enables subscribers to form closed user
groups with restricted access (both access to and from).
The CUG supplementary service is described in GSM 02.85. This service is provided on
prior arrangement with the service provider. Subscription options should be selected at
implementation.
The +CCUG command is used to:

❑ activate/deactivate the control of CUG information for all following outgoing calls,
❑ select a CUG index,
❑ suppress outgoing access (OA). OA allows a member of a CUG to place calls out-
side the CUG.
❑ suppress the preferential CUG. Preferential is the default CUG used by the net-
work when it does not receive an explicit CUG index.

10.16.2 Syntax:
Command syntax: AT+CCUG = <n> [ ,<index> [ <info> ] ]

10.16.3 Defined values:


<n>
0: Disable CUG mode (default)
1: Enable CUG mode

<index>
0-9: CUG index (0 default),
10: Preferred CUG

<info>
0: No information (default)
1: Suppress OA
2: Suppress preferential CUG
3: Suppress OA and preferential CUG
To activate the control of the CUG information by call, add [G] or [g] to the ATD command.
Index and info values will be used.

89
11 Data commands

11.1 Using AT Commands during a data connection


To use AT Commands during a data connection (e.g. while the product is in online mode),
it is necessary either to switch to offline mode, or to use the specific +WMUX command to
enable Commands / Data multiplexing.

11.1.1 Switch from online to offline mode


To switch from online mode to offline mode, the “+++” sequence must be sent. Following
this, the product gets back to offline mode with an “OK” response, and an AT command
can be sent.
NOTE: the “+++” sequence only works with the +ICF command using the following settings:
❑ 8 data bits, with no parity
❑ 7 data bits, with even parity

11.1.2 Switch from offline to online mode


See the ATO command description.

90
11.2 Bearer type selection +CBST

11.2.1 Description:
This command applies to both outgoing and incoming data calls, but in a different way.
For an outgoing call, the two parameters (e.g. <speed> and <ce>) apply, whereas for an
incoming call, only the <ce> parameter applies.
NOTE 1: For incoming calls, if <ce> is set to T only and the network offers NT only or vice versa, then
the call is released.
NOTE 2: The former values of 100 and 101 for <ce> are retained for compatibility purposes but should
no longer be used, values 2 and 3 should be used instead.

11.2.2 Syntax:
Command syntax: AT+CBST= <speed>, <name>, <ce>
COMMAND POSSIBLE RESPONSES
AT+CBST=?+CBST: (0-8,65,66,68,70,71),(0),(0-3)
OK
Note: Test command Note: Data 14,4 kbps not supported
AT+CBST=?+CBST: (0-8,12,14,65,66,68,70,71,75),(0),(0-3)
OK
Note: Test command Note: Data 14,4 kbps not supported
AT+CBST=7,0,1 OK
Note: Ask for a bearer Note: Bearer supported
AT+CBST?+CBST:7,0,1
OK
Note: Current values Note: Command valid
AT+CBST=81,0,0 +CME ERROR : 4
Note: Ask for a bearer Note: Bearer not supported

91
11.2.3 Defined values:
No data compression is provided and only asynchronous modem is supported (<name> = 0).
<speed>
0: (default) Autobauding (modem type: none)
1: 300 bps (modem type: V.21)
2: 1200 bps (modem type: V.22)
3: 1200/75 bps (modem type: V.23)
4: 2400 bps (modem type: V.22bis)
5: 2400 bps (modem type: V.26ter)
6: 4800 bps (modem type: V.32)
7: 9600 bps (modem type: V.32)
8: Specific
12 : 9600 bps (modem type: V.34)
14*: 1400 bps (modem type : V.34)
65: 300 bps (modem type: V.110)
66: 1200 bps (modem type: V.110)
68: 2400 bps (modem type: V.110)
70: 4800 bps (modem type: V.110)
71: 9600 bps (modem type: V.110)
75*: 14400 bps (modem type: V.110)
(*)This speed configures data and fax 14.4 kbps bearers.

<ce>
Connection element
<ce>
0: Transparent only
1: (default) Non transparent only
2: Transparent preferred
3: Non transparent preferred

92
11.3 Select mode +FCLASS

11.3.1 Description:
This command puts the product into a particular operating mode (data or fax).

11.3.2 Syntax:
Command syntax: AT+FCLASS= <n>
COMMAND POSSIBLE RESPONSES
AT+FCLASS=? +FCLASS: (0,1)
OK
Note: Test command Note: Fax class 2 not supported
AT+FCLASS=? +FCLASS: (0,1,2)
OK
Note: Test command Note: Fax class 2 supported
AT+FCLASS=0 OK
Note: Data mode requested Note: Command valid
AT+FCLASS=1 OK
Note: Fax class 1 mode requested Note: Command valid
AT+FCLASS? +FCLASS: 1
OK
Note: Current value Note: Command valid

11.3.3 Defined values:


<n>
0: Data
1: Fax class 1
2: Fax class 2

93
11.4 Service reporting control +CR

11.4.1 Description:
This command enables a more detailed type of service reporting in the case of incoming
or outgoing data calls. Before sending the CONNECT response to the application, the
product will specify the type of data connection that has been set up.
These report types are :
+CR: ASYNC For asynchronous transparent
+CR: REL ASYNC For asynchronous non-transparent

11.4.2 Syntax:
Command Syntax: AT+CR
COMMAND POSSIBLE RESPONSES
AT+CR=0 OK
Note: Extended reports disabled Note: Command valid
AT+CR=1 OK
Note: Extended reports enabled Note: Command valid

11.5 Cellular result codes +CRC

11.5.1 Description:
This command gives more detailed ring information for an incoming call (voice or data).
Instead of the string “RING”, an extended string is used to indicate which type of call is
ringing (e.g. +CRING: VOICE).
These extended indications are:

+CRING: ASYNC for asynchronous transparent


+CRING: REL ASYNC for asynchronous non-transparent
+CRING: VOICE for normal speech.
+CRING : FAX for fax calls

11.5.2 Syntax:
Command Syntax: AT+CRC
COMMAND POSSIBLE RESPONSES
AT+CRC=0 OK
Note: Extended reports disabled Note: Command valid
AT+CRC=1 OK
Note: Extended reports enabled Note: Command valid

94
11.6 DTE-DCE local rate reporting +ILRR

11.6.1 Description:
This parameter controls whether or not the extended-format “+ILRR:<rate>” information
text is transmitted from the DCE to the DTE. The <rate> reported represents the current
(negotiated or renegotiated) DTE-DCE rate.
If enabled, the intermediate result code is transmitted in an incoming or outgoing data
call, after any data compression report, and before any final result code (CONNECT).
<rate> can take the following values: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600,
115200.

11.6.2 Syntax:
Command Syntax: AT+ILRR
COMMAND POSSIBLE RESPONSES
AT+ILRR=0 OK
Note: Local port rate report disabled Note: Command valid
AT+ILRR=1 OK
Note: Local port rate report enabled Note: Command valid

11.7 Radio link protocol parameters +CRLP

11.7.1 Description:
This command allows the radio link protocol parameters used for non transparent data
transmission to be changed.

11.7.2 Syntax:
Command syntax: AT+CRLP=<iws>,<mws>,<T1>,<N2>, <ver>
COMMAND POSSIBLE RESPONSES
AT+CRLP=? +CRLP: (0-61),(0-61),(40-255),(1,255),(0)
OK
Note: Test command Note: V42bis not supported
AT+CRLP=? +CRLP: (0-61),(0-61),(40-255),(1,255),(0,1)
OK
Note: Test command Note: V42bis supported
AT+CRLP=61,61,48,6,0 OK
Note: Set new parameters Note: Command valid
AT+CRLP? AT+CRLP: 61,61,48,6,0
Note: Current values Note: Command valid

95
11.7.3 Defined values:
This command accepts 5 parameters.
<iws> 0-61: Down window size, (default is 61),
<mws> 0-61: Up window size, (default is 61),
<T1> 40-255: Acknowledgement timer in units of 10ms, (default is 48)
<N2> 1-255: Retransmission attempts, (default is 6),
<ver> 0-1: Version number.
If V42bis is supported the version is 1
If V42bis is not supported the version is 0

11.8 Others radio link parameters +DOPT

11.8.1 Description:
This Wavecom specific command allows some supplementary radio link protocol
parameters to be changed.

11.8.2 Syntax:
Command syntax: AT+DOPT=<reset_allowed>,<dtx_allowed>
COMMAND POSSIBLE RESPONSES
AT+DOPT=1 OK
Note: Set new parameters Note: Command valid
AT+DOPT+? (0,1),(0,1)
OK
Note: Test command Note: DTX is supported
AT+DOPT=1,1 OK
Note: Set new parameters Note: Command valid
AT+DOPT? 1,1
OK
Note: Current values Note: Command valid

11.8.3 Defined values:


<reset_allowed>
0: Data communication is hung up in case of bad radio link.
1: (default) Data communication continues in case of bad radio link (possible loss of data)

< dtx_allowed >


0: Normal mode
1: (default) Economic battery mode (not supported by all networks)

96
11.9 Select data compression %C

11.9.1 Description:
This command enables or disables data compression negotiation if this feature is
supported on the product.

11.9.2 Syntax:
Command Syntax: AT%C<n>
COMMAND POSSIBLE RESPONSES
AT%C0 OK
Note: Command Note: Feature supported
AT%C2 OK
Note: Command Note: V42bis supported
AT%C? 2
OK
Note: Current value Note: Command valid

11.9.3 Defined values:


<n>
0: (default) no compression
2: V42bis compression if supported

97
11.10 V42 bis data compression +DS

11.10.1 Description:
This command enables or disables V.42bis data compression if this feature is supported
on the product.

11.10.2 Syntax:
Command Syntax: AT+DS=<dir>,<neg>,<P1>,<P2>
COMMAND POSSIBLE RESPONSES
AT+DS=? +DS: (0-3),(0,1),(512-4096),(6-250)
OK
Note: Test command Note:
AT+DS=3,0,4096,250 OK
Note: Set new parameters Note: Command valid
AT+DS?+DS: 3,0,4096,20
OK
Note: Current values Note: Command valid

11.10.3 Defined values:


Four numeric sub-parameters are accepted:
<dir>
specifies the desired direction(s) of operation of the data compression function; from the
DTE point of view, (default is 3),
<dir>
0: Negotiated … no compression
1: Transmit only
2: Receive only
3: Both directions, accept any direction

<neg>
specifies whether or not the DCE should continue to operate if the desired result is not
obtained, (default is 0),
<neg>
0: Do not disconnect if V.42 bis is not negotiated by the remote DCE as specified in <dir>
1: Disconnect if V.42 bis is not negotiated by the remote DCE as specified in <dir>

<P1>
512-4096: specifies the maximum number of dictionary entries that should be negotiated,
(default is 4096),

<P2>
6-250: specifies the maximum string length to be negotiated, (default is 250).

98
11.11 V42 bis data compression report +DR

11.11.1 Description:
If this feature is provided by the product this command determines whether or not the use
of V42bis is given in an incoming or outgoing data call.
The intermediate result code represents current DCE-DCE data compression type. The
format of this result code is as follows:

+DR: NONE Data compression is not in use


+DR: V42B Rec. V.42 bis is in use in both directions
+DR: V42B RD Rec. V.42 bis is in use in receive direction only
+DR: V42B TD Rec. V.42 bis is in use in transmit direction only

The +DR intermediate result code, if enabled, is issued before the final result code, before
the +ILRR intermediate report and after the service report control +CR.

11.11.2 Syntax:
Command Syntax: AT+DR
COMMAND POSSIBLE RESPONSES
AT+DR=? +DR: (0-1)
OK
Note: Test command Note:
AT+DR=1 OK
Note: Reporting enabled Note: Command valid
AT+DR? +DR: 1
OK
Note: Current value Note: Command valid

99
11.12 Select data error correcting mode \N

11.12.1 Description:
If this feature is provided by the product, this command controls the preferred error
correcting mode for a data connection. It can only be used for transparent data
transmission.
If the V42 feature is provided, the product authorizes LAPM error correction mode.
If the MNP2 feature is provided, the product authorizes MNP error correction mode.

11.12.2 Syntax:
Command Syntax: AT\N<n>
COMMAND POSSIBLE RESPONSES
AT\N0 OK
Note: no error correction
AT\N? 0
Note: Current value OK
Note: Command valid
AT\N4 +CME ERROR: 3
Note: LAPM error correction selection Note: V42 feature is not provided

11.12.3 Defined values:


<n>
0: (default) Disables error correction mode
2: Selects an auto reliable mode (LAPM connection, then MNP connection)
4: Selects LAPM error correction mode
5: Selects MNP error correction mode

NOTE: +E prefixed commands of V.25 ter are not used.

100
12 Fax commands
The fax service provided by the product is class 1 compatible. However, only the core
commands defined by ITU T.31 are supported. This means that commands such as
AT+FAR, +FCC, etc. are not supported.
Autobauding must be enabled to set up the product for fax.
All set commands below return an ERROR response code if they are not issued during
communication.

12.1 Transmit speed +FTM

12.1.1 Description:
This command sets the fax transmit speed.

12.1.2 Syntax:
Command syntax: AT+FTM=<speed>
COMMAND POSSIBLE RESPONSES
AT+FTM=? (24,48,72,73,74,96,97,98,121,122,145,146)
OK
Note: Test command Note: Fax 14.4 kbps supported

12.1.3 Defined values:


<speed>
24: 2400 bps (modem type: V.27ter)
48: 4800 bps (modem type: V.27ter)
72: 7200 bps (modem type: V.29)
73: 7200 bps (long) (modem type: V.17)
74: 7200 bps (short) (modem type: V.17)
96: 9600 bps (modem type: V.29)
97: 9600 bps (long) (modem type: V.17)
98: 9600 bps (short) (modem type: V.17)
121: 12000 bps (long) (modem type: V.17)
122: 12000 bps (short) (modem type: V.17)
145: 14400 bps (long) (modem type: V.17)
146: 14400 bps (short) (modem type: V.17)

101
12.2 Receive speed +FRM

12.2.1 Description:
This command sets the fax receive speed.

12.2.2 Syntax:
Command syntax: AT+FRM=<speed>
COMMAND POSSIBLE RESPONSES
AT+FRM=? (24,48,72,73,74,96,97,98,121,122,145,146)
OK
Note: Test command Note: Fax 14.4 kbps supported

12.2.3 Defined values:


The speed values are identical to those of the +FTM command (see 12.1.3 Defined values).

12.3 HDLC transmit speed +FTH

12.3.1 Description:
This command sets the fax transmit speed, using the HDLC protocol.

12.3.2 Syntax:
Command syntax: AT+FTH=<speed>
COMMAND POSSIBLE RESPONSES
AT+FTH=? (3)
OK
Note: Test command Note:

12.3.3 Defined values:


<speed> can only take the value 3, which corresponds to V.21 channels 300 bps.

12.4 HDLC receive speed +FRH

12.4.1 Description:
This command sets the fax receive speed, using the HDLC protocol.

12.4.2 Syntax:
Command syntax: AT+FRH=<speed>
COMMAND POSSIBLE RESPONSES
AT+FRH=? (3)
OK
Note: Test command Note:

12.4.3 Defined values:


<speed> can only take the value 3, which corresponds to V.21 channels 300 bps.

102
12.5 Stop transmission and wait +FTS

12.5.1 Description:
This command stops transmission for the period specified.

12.5.2 Syntax:
Command syntax: AT+FTS=<n>
COMMAND POSSIBLE RESPONSES
AT+FTS=? (0-255)
OK
Note: Test command Note:
AT+FTS=50 OK
Note: Stops transmission and waits for 0.5s Note: Command valid

12.5.3 Defined values:


<n>
silence period (units of 10 ms).

12.6 Receive silence +FRS

12.6.1 Description:
This command causes the modem to stop listening to the network and report back to the
DTE after the specified period.
It is aborted if any character is received from the application.

12.6.2 Syntax:
Command syntax: AT+FRS=<n>
COMMAND POSSIBLE RESPONSES
AT+FRS=? (0-255)
OK
Note: Test command Note:
AT+FRS=50 OK
Note: Stops transmission and waits for 0.5s Note: Command valid

12.6.3 Defined values:


<n> is in units of 10 ms.

103
12.7 Setting up the PC fax application:

The recommended fax application is Delrina WinFax v8.0.


It should be configured as follows (menu Setup/Fax Modem Setup):
❑ Port: any com
❑ Model: Generic Class 1 (hardware flow control). A generic class 1 with software
flow control can also be selected.
❑ Init: default string is suitable for the product
❑ Reset: default string is suitable for the product
❑ Maximum Transmit Rate: 9600 baud (if higher rate will be automatically cut back
to 9600 baud).
Other settings are of no relevance for the GSM unit: they can be modified.

104
13 Fax class 2 commands
If the feature is supported, the commands +FDT, +FDR, +FET, +FPTS and +FK must be used
during communication only.
The other commands, +FBOR, +FBUF, +FCQ, +FCR, +FDCC, +FDIS, +FLID and +FPHCTO,
cannot be used during communication.

13.1 Transmit Data +FDT

13.1.1 Description:
This command prefixes data transmission.

13.1.2 Syntax:
Command syntax: AT+FDT

13.2 Receive Data +FDR

13.2.1 Description:
This command initiates data reception.

13.2.2 Syntax:
Command Syntax: AT+FDR

13.3 Transmit page ponctuation +FET

13.3.1 Description:
This command ponctuates page and document transmission after +FDT commands. It
indicates that the current page is complete, and whether or not there are additional pages
to be sent.

13.3.2 Syntax:
Command syntax: AT+FET=<ppm>

13.3.3 Defined values:


<ppm>
0: Another page next, same document
1: Another document next
2: No more pages or documents
3: Another partial page next
4: Another page, procedure interrupt
5: Another document, procedure interrupt
6: All done, procedure interrupt
The remote station should respond with +FPTS:<ppr>

105
13.4 Page transfer status parameters +FPTS

13.4.1 Description:
This command sets post page transfer response.

13.4.2 Syntax:
Command syntax: AT+FPTS=<ppr>

13.4.3 Defined values:


<ppm>
1: Page good
2: Page bad ; retrain requested
3: page good ; retrain requested
4: Page bad ; interrupt requested
5: Page good ; interrupt requested

13.5 Terminate Session +FK

13.5.1 Description:
This command causes the product to terminate the session.

13.5.2 Syntax:
Command syntax: AT+FK

13.6 Page transfer bit order +FBOR

13.6.1 Description:
This command sets the bit order for negotiation and fax page transfer. The order is related
to the bit order or radio link.

13.6.2 Syntax:
Command syntax: AT+FBOR=<n>
COMMAND POSSIBLE RESPONSES
AT+FBOR=? (0-3)
OK
Note: Test command Note:

13.6.3 Defined values:

<n> Bit order for negotiation Bit order for page transfer
0(default) Same Same
1 Same Reverse
2 Reverse Same
3 Reverse Reverse

106
13.7 Buffer size report +FBUF

13.7.1 Description:
This command requests the size of the exchange buffer between the modem and the fax
application.
Only the read command is supported.

13.7.2 Syntax:
Command Syntax: AT+FBUF
COMMAND POSSIBLE RESPONSES
AT+FBUF? 1024
OK
Note: Current value Note: Command valid

13.8 Copy quality checking +FCQ

13.8.1 Description:
This command controls Copy Quality checking for receiving faxes.

13.8.2 Syntax:
Command Syntax: AT+FCQ=<n>
COMMAND POSSIBLE RESPONSES
AT+FCQ=? (0)
OK
Note: Test command Note:

13.9 Capability to receive +FCR

13.9.1 Description:
This commands controls the capability of the modem to accept incoming faxes.

13.9.2 Syntax:
Command syntax: AT+FCR=<n>
COMMAND POSSIBLE RESPONSES
AT+FCR=? (0,1)
OK
Note: Test command Note:

13.9.3 Defined values:


<n>
0: The modem will not accept incoming faxes.
1: (default) The modem will accept incoming faxes.

107
13.10 Current sessions parameters +FDIS

13.10.1 Description:
This command allows the DTE to parameter the capabilities used for the current session.

13.10.2 Syntax:
Command syntax: AT+FDIS=<vr>,<br>,<wd>,<ln>,<df>,<ec>,<bf>,<st>
COMMAND POSSIBLE RESPONSES
(0,1),(0-5),(0-2),(0-2),(0-3),(0),(0),(0-7)
AT+FDIS=? OK

Note: Note: Fax ECM not supported


Fax 14,4 kbps supported
(0,1),(0-3),(0-2),(0-2),(0-3),(0),(0),(0-7)
OK
Note: Fax ECM not supported
Fax 14,4 kbps not supported

13.10.3 Defined values:


This command accepts eight numeric parameters (of the T30 standard):
<vr>: Vertical Resolution,
<vr>
0: (default) Normal: 98 lpi
1: Fine: 196 lpi

<br> Bit Rate,


<br>
0: 2400 bps (modem type: V.27 ter)
1: 4800 bps (modem type: V.27 ter)
2: 7200 bps (modem type: V.29)
3: 9600 bps (modem type: V.29, V.17)
4*: 12000 bps (modem type: V.33, V.17)
5*: 14400 bps (modem type: V.33, V.17)
(*) Only when product supports 14,4 kbps data feature

If this feature is supported, default is 5, otherwise default is 3.


<wd> Page Width,
<wd>
0: (default) 1728 pixels in 215 mm
1: 2048 pixels in 255 mm
2: 2432 pixels in 303 mm

108
<in> Page Length,
< in >
0: A4, 297 mm
1: B4, 364 mm
2: (default) Unlimited

<df> Data Compression Format,


< df >
0: (default) 1-D modified huffman
1: 2-D modified read
2: 2-D uncompressed mode
3: 2-D modified modified read

<ec> Error Correction,


< ec >
0: Disable Fax ECM
1*: Enable Fax ECM, 64 bytes/frame
2*: Enable Fax ECM, 256 bytes/frame
(*) Only when product supports fax Error Correction Mode feature
If this feature is supported, default is 2, else default is 0.

<bf> : Binary File Transfer,


Only <bf> set to 0 is supported.

<st> : Scan Time per line,

<st> Description <vr>=0 Description <vr>=1


0(default) 0 ms 0 ms
1 5 ms 5 ms
2 10 ms 5 ms
3 10 ms 10 ms
4 20 ms 10 ms
5 20 ms 20 ms
6 40 ms 20 ms
7 40 ms 40 ms

109
13.11 DCE capabilities parameters +FDCC

13.11.1 Description:
This command allows the DTE to parameter the capabilities used for any session.

13.11.2 Syntax:
Command syntax: AT+FDCC=<vr>,<br>,<wd>,<ln>,<df>,<ec>,<bf>,<st>
COMMAND POSSIBLE RESPONSES
AT+ FDCC=? (0,1),(0-5),(0-2),(0-2),(0-3),(0-2),(0),(0-7)
OK
Note: Test command Note: Fax ECM supported
Fax 14,4 kbps supported
(0,1),(0-5),(0-2),(0-2),(0-3),(0),(0),(0-7)
OK
Note: Fax ECM not supported
Fax 14,4 kbps supported
(0,1),(0-3),(0-2),(0-2),(0-3),(0-2),(0),(0-7)
OK
Note: Fax ECM supported
Fax 14,4 kbps not supported
(0,1),(0-3),(0-2),(0-2),(0-3),(0),(0),(0-7)
OK
Note: Fax ECM not supported
Fax 14,4 kbps not supported

13.11.3 Defined values:


The parameters and default values are the same as for the +FDIS command (see 13.10.3
Defined values).

13.12 Local ID string +FLID

13.12.1 Description:
This command allows the local ID string to be defined.

13.12.2 Syntax:
Command syntax: AT+FLID=”<string>”
The string has a limited size, and accepts any characters between 32 and 127.
COMMAND POSSIBLE RESPONSES
AT+FLID=? (20),(32-127)
Note: Test command OK

110
13.13 Page transfer timeout parameter +FPHCTO

13.13.1 Description:
This command sets the period the modem waits for another page before it assumes there
are no more pages and aborts.

13.13.2 Syntax:
Command syntax: AT+FPHCT0=<n> (default is 30)
COMMAND POSSIBLE RESPONSES
AT+FPHCTO=? (0-255)
Note: Test command OK

13.14 Fax Class 2 indication messages


The following messages are used to indicate DCE Responses. They are used in
communication only.
+FCON:
This response indicates connection with a fax machine.
+FDCS <vr>,<br>,<wd>,<ln>,<df>,<ec>,<bf>,<st>:
This response reports current session capabilities. The parameters are the same than
those of AT+FDIS command (see 13.10).
+FDIS <vr>,<br>,<wd>,<ln>,<df>,<ec>,<bf>,<st>:
This response reports remote capabilities. The parameters are the same than those of
AT+FDIS command (see 13.10).
+FCFR:
This response indicates confirmation to receive.
+FTSI “<string>”:
This response reports the received transmit station ID string.
+FCSI “<string>”:
This response reports the received called station ID string.
+FPTS <ppr>:
This response reports received page transfer status. The parameter is the same than the
one of AT+FPTS command (see 13.4).
+FET <ppm>:
This response reports post page message response. The parameter is the same than the
one of AT+FET command (see 13.3).
+FHNG <cause>:
This response reports the hang-up cause. It indicates that the call has been terminated.
<cause>
0: Normal end of connection.
10: Unspecified transmit phase A error.
20: Unspecified transmit phase B error.
40: Unspecified transmit phase C error.
50: Unspecified transmit phase D error.
70: Unspecified receive phase B error.
90: Unspecified receive phase C error.
100: Unspecified receive phase D error.

111
14 V24-V25 commands

14.1 Fixed DTE rate +IPR

14.1.1 Description:
This commands specifies the data rate at which the DCE will accept commands.

14.1.2 Syntax:
Command Syntax: AT+IPR
COMMAND POSSIBLE RESPONSES
AT+IPR? +IPR: 9600
OK
Note: Note: Current rate is 9600 bps
AT+IPR=? +IPR: (0,2400,4800,9600,19200),
(300,600,1200,38400,57600,115200)
OK
Note: Note: Possible value (*)
AT+IPR=38400 OK
Note: Note: Disable autobauding and set rate to 38400 bps
AT+IPR=0 OK
Note: Note: Enable autobauding
(*) the first set of values indicates the range of auto-detectable speeds.
The second set of values indicates all possible speeds that can be used by the DCE.
Autobauding is supported (operating from 1200 to 38400 baud). However some
constraints have to be taken into account:
any AT command issued by the DTE must start with a capital ‘A’ and ‘T’ (or ‘\’), otherwise
the DCE may return some garbage characters and become de-synchro-nized. Should this
happen, the DTE simply issues ‘AT\r’ (at 2400 or 4800 bauds) once or twice or just ‘AT’ (at
9600 bauds) to re-synchronize the modem.
the DTE waits for 1ms after receiving the last character of the AT response (which is
always ‘\n’ or 0x0A) to send a new AT command at either the same rate or a new rate.
Should this delay be ignored, the DCE can become de-synchronised. Once again, sending
’AT\r’ once or twice or just ‘AT’ causes the DCE to recover.

CAUTION: when starting up, if autobauding is enabled and no AT command has yet been
received, the product sends all unsolicited responses (like RING) at 9600 bauds.

112
14.2 DTE-DCE character framing +ICF

14.2.1 Description:
This command is used to determine the local serial port start-stop (asynchronous)
character framing that the DCE uses.

14.2.2 Syntax:
Command syntax: AT+ICF= <format>, <parity>
COMMAND POSSIBLE RESPONSES
AT+ICF? +ICF: 3,4
OK
Note: Note: Current values
AT+ICF=? +ICF: (1-6),(0-4)
OK
Note: Note: Possible values
AT+IPR=38400 OK
Note: Note: Disable autobauding and set rate to 38400 bps
AT+ICF=0,0 OK
Note: Note: New values

14.2.3 Defined values:


<format>
0: Autodetect (not supported)
1: 8 Data 2 Stop (supported)
2: 8 Data 1 Parity 1 Stop (supported)
3: 8 Data 1 Stop (supported)
4: 7 Data 2 Stop (supported)
5: 7 Data 1 Parity 1 Stop (supported)
6: 7 Data 1 Stop (supported)

<parity>
0: Odd (supported)
1: Even (supported)
2: Mark (supported)
3: Space (supported)
4: None (supported)

NOTE 1: setting a character framing different from 8N1 will disable autobauding (in the case it was
activated). However setting it back to 8N1 will not re-enable autobaud.
NOTE 2: setting the framing to 8N1 will let the autobauding enabled, if it was already enabled
(implying framing was already 8N1).

113
14.3 DTE-DCE local flow control +IFC

14.3.1 Description:
This command is used to control the operation of local flow control between the DTE and
DCE.

14.3.2 Syntax:
Command Syntax: AT+IFC=<DCE_by_DTE>,<DTE_by_DCE>
COMMAND POSSIBLE RESPONSES
AT+IFC? +IFC: 2,2
OK
Note: Note: Current values
AT+IFC=? +IFC: (0,2),(0,2)
OK
Note: Note: Possible values
AT+IFC=0,0 OK
Note: Note: New values

14.3.3 Defined values:


<DCE_by_DTE>
0: none (supported)
1: Xon/Xoff local circuit 103 (not supported)
2: RTS (supported)
3: Xon/Xoff global on circuit 103 (not supported)

IMPORTANT NOTE: when this parameter is set to 2 (DTE invokes flow control throught RTS) DCE
behaviour is as follows:

If the DCE has never detected RTS in the high (or ON) condition since startup then it
ignores RTS as it assumes that this signal is not connected.
As soon as the DCE detects RTS high the signal acts on it. Therefore subsequent RTS
transition to OFF will prevent the DCE from sending any further data in both online and
offline modes.
This behaviour allows the user to use the default settings (hardware flow control) and
leave RTS disconnected. In the case where RTS is connected and is high at least once, it
acts on the DCE.

< DTE_by_DCE >


0: none (supported)
1: Xon/Xoff circuit 104 (not supported)
2: CTS (supported)

When this parameter is set to 0 (none) then CTS is kept high all the time.

114
14.4 Set DCD signal &C

14.4.1 Description:
This commands controls the Data Carrier Detect (DCD) signal.

14.4.2 Syntax:
Command Syntax: AT&C
COMMAND POSSIBLE RESPONSES
AT&C0 OK
Note: DCD always on Note: Command valid
AT&C1 OK
Note: DCD matches state of the remote
modem’s data carrier Note: Command valid

14.5 Set DTR signal &D

14.5.1 Description:
This commands controls the Data Terminal Ready (DTR) signal.

14.5.2 Syntax:
Command Syntax: AT&D
COMMAND POSSIBLE RESPONSES
AT&D0 OK
Note: The DTR signal is ignored Note: Command valid
AT&D1 OK
Note: Modem switches from data to command
mode when DTR switches from ON to OFF Note: Command valid
AT&D2 OK
Note: Upon DTR switch from ON to OFF,
the call is released Note: Command valid

115
14.6 Set DSR signal &S

14.6.1 Description:
This commands controls the Data Set Ready (DSR) signal.

14.6.2 Syntax:
Command Syntax: AT&S
COMMAND POSSIBLE RESPONSES
AT&S0 OK
Note: DSR always on Note: Command valid
AT&S1 OK
Note: DSR off in command mode, DSR
on in data mode Note: Command valid

14.7 Back to online mode O

14.7.1 Description:
If a connection has been established and the ME is in command mode, this command
allows you to return to online data mode.

14.7.2 Syntax:
Command Syntax: ATO
COMMAND POSSIBLE RESPONSES
ATO OK
Return from offline mode to online mode

14.8 Result code suppression Q

14.8.1 Description:
This command determines whether the mobile equipment sends result codes or not

14.8.2 Syntax:
Command Syntax: ATQ
COMMAND POSSIBLE RESPONSES
ATQ0 OK
Note: DCE transmits result codes Note: Command valid
ATQ1 (none)
Note: Result codes are suppressed and not transmitted Note: No response

116
14.9 DCE response format V

14.9.1 Description:
This command determines the DCE response format, with or without header characters
<CR><LF>, and with the use of numeric result codes.

V0 V1
Information responses <text><CR><LF> <CR><LF>
<text><CR><LF>
Result codes <numeric code><CR> <CR><LF>
<verbose code><CR><LF>

14.9.2 Syntax:
Command Syntax: ATV
COMMAND POSSIBLE RESPONSES
ATV0 0
Note: DCE transmits limited headers and trailers
and numeric result codes Note: Command is valid (0 means OK)
ATV1 OK
Note: DCE transmits full headers and trailers and
verbose response text Note: Command valid

14.10 Default configuration Z

14.10.1 Description:
This command restores the configuration profile. Any call is released.

14.10.2 Syntax:
Command Syntax: ATZ
COMMAND POSSIBLE RESPONSES
ATZ Ok
Note: Note: Command valid

117
14.11 Save configuration &W

14.11.1 Description:
This commands writes the active configuration to a non-volatile memory (EEPROM).
Description of the stored parameters is given in paragraph 18.10

14.11.2 Syntax:
Command Syntax: AT&W
COMMAND POSSIBLE RESPONSES
AT&W OK
Note: Writes current configuration to EEPROM Note: Command valid

14.12 Auto-tests &T

14.12.1 Description:
AT&T0 is used to perform auto-tests. The response will be OK if no software problem is
detected (EEPROM, RAM and ROM checksums), otherwise a simple ERROR response is
sent.
AT&T1 is used to close the audio loop and AT&T2 is used to open the audio loop. This is
used to validate the audio loop (microphone to speaker).

14.12.2 Syntax:
Command Syntax: AT&T
COMMAND POSSIBLE RESPONSES
AT&T0 OK
Note: Perform software auto-tests Note: No software problem detected, all checksums
are correct
AT&T1 OK
Note: Do the audio loop test (close) Note: Command valid
AT&T2 OK
Note: Stop the audio loop test (open) Note: Command valid

118
14.13 Echo E

14.13.1 Description:
This command is used to determine whether or not the modem echoes characters
received by an external application (DTE).

14.13.2 Syntax:
Command Syntax: ATE
COMMAND POSSIBLE RESPONSES
ATE0 OK
Note: Characters are not echoed Note: Done
ATE1 OK
Note: Characters are echoed Note: Done

14.14 Restore factory settings &F

14.14.1 Description:
This command is used to restore the factory settings from EEPROM.
The settings which are restored are listed in appendix 18.10.

14.14.2 Syntax:
Command Syntax: AT&F
COMMAND POSSIBLE RESPONSES
AT&F OK
Note: Ask for restoring the factory settings Note: Done
AT&F0 OK
Note: Ask for restoring the factory settings Note: Done

14.15 Display configuration &V

14.15.1 Description:
This command is used to display the modem configuration.
&V
&V0: Display the modem configuration in RAM.
&V1: Display the modem configuration in EEPROM.
&V2: Display the modem factory configuration.

The parameters displayed are the following :


Q, V, S0, S2, S3, S4, S5,
+CR, +CRC, +CMEE, +CBST,
+SPEAKER, +ECHO, &C, &D, %C
+IPR, +ICF, +IFC

119
14.15.2 Syntax:
Command Syntax: AT&V
COMMAND POSSIBLE RESPONSES
AT&V Q:0 V:1 S0:000 S2:043 S3:013 S4:010 S5:008
+CR:0 +CRC:0 +CMEE:0 +CBST:0,0,1
+SPEAKER:0 +ECHO:0,0 &C:1 &D:2 %C:0
+IPR:9600 +ICF:3,4 +IFC:2,2
OK
Note: Display active parameters in RAM Note: Done
For Echo the first value corresponds to Echo cancellation 1.

14.16 Request identification information I

14.16.1 Description:
This command causes the product to transmit one or more lines of specific information
text.
I0: Display manufacturer followed by model identification. This command is equivalent to
+CGMI and +CGMM.
I3: Display revision identification (equivalent to +CGMR).
I4: Display modem configuration in RAM (equivalent to &V0).
I5: Display modem configuration in EEPROM (equivalent to &V1).
I6: Display modem data features. This command lists the supported data rates, data
modes, and fax classes.
I7: Display modem voice features.
If the value is different, an “OK” string will be sent back.

120
14.16.2 Syntax:
Command Syntax: ATI
COMMAND POSSIBLE RESPONSES
ATI0 WAVECOM MODEM
900P
OK
Note: Manufacturer and model identifications Note: GSM 900 MHz primary band
ATI3 310_G250.51 806216 032199 17:04
OK
Note: Revision identification Note: Software release 3.10 ,revision 51 generated on the
21st of March 1999
ATI6 DATA RATES:
AUTOBAUD,300,1200,1200/75,2400,4800,9600,14400
DATA MODES : T/NT,ASYNCHRONOUS
FAX CLASS 1,2
OK
Note: Modem data features Note: Done
ATI7 SPEECH CODINGS: FR,EFR,HR
OK
Note: Modem voice features Note: Done

14.17 Data / Commands Multiplexing +WMUX

14.17.1 Description:
This specific command allows to manage the data / AT commands multiplexing mode.
See appendix 18.13 for the Data / Commands multiplexing protocol description.

14.17.2 Syntax:
Command syntax: AT+WMUX=<mode>
COMMAND POSSIBLE RESPONSES
AT+WMUX=? +WMUX: (0-1)
OK
AT+WMUX? +WMUX: 0
OK
Data / Commands multiplexing disabled.
AT+WMUX=1 OK
Enable Data / Commands multiplexing.

14.17.3 Defined values:


<mode>
0: Multiplexing disabled. When the product is online (data communication in progress),
no AT command can be used (default).
1: Multiplexing enabled. Data flows and AT commands are multiplexed while in online
mode (data communication in progress).

121
15 Specific AT commands

15.1 Cell environment description +CCED

15.1.1 Description:
This command can be used by the application to retrieve the parameters of the main cell
and of up to six neighbouring cells.
There are two possible methods for the external application to ascertain these cell
parameters: on request by the application or automatically by the product every 5
seconds.
Automatic mode is not supported during registration.

15.1.2 Syntax:
Command syntax: AT+CCED=<mode>[, <requested dump>]

15.1.3 Defined values:


<mode>
0: One shot requested
1: Automatic shots requested
2: Stop automatic shots

<requested dump>
1: Main Cell : if the Cell Identity is available MCC, MNC, LAC, CI, BSIC, BCCH Freq
(absolute), RxLev, RxLev Full, RxLev Sub, RxQual, RxQual Full, RxQual Sub,Idle TS
if the Cell Identity is not available MCC, MNC, LAC, BSIC, BCCH Freq (absolute), RxLev,
RxLev Full, RxLev Sub, RxQual, RxQual Full, RxQual Sub,Idle TS
2: Neighbour1 to Neighbour6 : if the Cell Identity is available MCC, MNC, LAC, CI, BSIC,
BCCH Freq (absolute), RxLev if the Cell Identity is not available MCC, MNC, LAC,, BSIC,
BCCH Freq (absolute), RxLev
4: Timing Advance
Combination (addition of the values) of the requested dump is supported.
Note that in idle mode, only RxLev measurements (on the main cell and on the
neighbouring cells) are made. The value of these RxLev is set in the RxLev Full field for the
main cell.
The response will be:
+CCED :<value>, … , <value>
OK
Where <value> is the ASCII string of the values (in decimal form except the LAC and CI
values which are in hexadecimal form) of the parameters. If a field cannot be measured –
or has no sense – the parameter is not filled in (two consecutive commas are then found).
If the <requested dump> parameter is absent, that of the last +CCED command (or 15 by
default) will be used.
Values of MCC/MNC are set to 0 in the case of “No service”.

122
15.2 Automatic RxLev indication +CCED

15.2.1 Description:
The CCED command has been extended to indicate the received signal strength indication
(rssi) of the main cell. The command principle has not changed.

15.2.2 Syntax:
Command Syntax: AT+CCED=<mode>[, <requested dump>]

15.2.3 Defined values:


<mode>
0: One shot requested
1: Automatic shots requested
2: Stop automatic shots

<requested dump>
8: Main cell RSSI indications (RxLev) from 0 to 31

The response will be a +CSQ response and not a +CCED response. The 07.07 format for
+CSQ is respected. The <ber> is not evaluated by this command, so the <ber> value will
always be 99.
+CSQ :<rssi>, 99
OK
This +CSQ response, when automatic shots are selected, is sent every time the <rssi>
measured by the product changes. Automatic shots are supported in idle mode and
during communication.
Combination (addition of the values) of the requested dump (1,2,4,8) are supported but the
activation or deactivation of this flow (8) does not affect the other flows. Both +CCED and
+CSQ responses may then be generated.
If the <requested dump> parameter is absent, the last +CCED command parameter (or 15
by default) will be used.

123
15.3 General Indications +WIND

15.3.1 Description:
Wavecom has introduced a general mechanism to send unsolicited non-standardized
indications to the application. The identified unsolicited non-standardized indications are:
- indication of a physical change on the SIM detect pin from the connector
(meaning SIM inserted, SIM removed)
- indication during mobile originated call setup that the calling party is ringing.
- Indication of the availability of the product to receive AT commands after boot.
For each of these indications, a “bit flow” has to be indicated.

15.3.2 Syntax:
Command syntax: AT+WIND= <IndLevel >

15.3.3 Defined values:


<IndLevel>
1 (bit-0): Hardware SIM Insert / Remove indications (Rack open/close) or SIM presence
after software reset
2 (bit-1): Calling party alert indication
4 (bit-2): Product is ready to process AT commands (except phonebooks, AOC, SMS),
but still in emergency mode.
8 (bit-3): Indication that the product is ready to process all AT commands, at the end of
init or after swapping to ADN in case of FDN configuration
16 (bit-4): Indication that a new call identifier has been created (after an ATD command,
+CCWA indication)
32 (bit-5): Indication that an active, held or waiting call has been released by network or
other party
64 (bit-6): Network service available indication
128 (bit-7): Network lost indication
256 (bit-8): Audio ON indication
512 (bit-9): SIM Phonebooks reload status
1024 (bit-10): Sim phonebooks checksum indication
2048 (bit-11): Interruption indication (only if FTR_INT is activated)

If <IndLevel> is equal to 0 (default value), no unsolicited “+WIND: <IndNb>” will occur.

Combination (addition of the values) is used to allow more than one indication flow.
0 ≥ IndLevel ≤ 4095

The response is OK if the values are in the previous range.

124
The supported events are:
<event>
0: The SIM presence pin has been detected as “SIM removed” (depending on 0 bit flow)
1: The SIM presence pin has been detected as “SIM inserted”
2: Calling party is alerting
3: Product is ready to process AT commands (except phonebooks, AOC, SMS), at init or
after AT+CFUN=1
4: Product is ready to process all AT commands, end of phonebook init or swap (FDN to ADN)
5: Call <idx> has been created (after ATD or +CCWA…)
6: Call <idx> has been released, after a NO CARRIER, a +CSSU: 5 indication, or after the
release of a call waiting
7: The network service is available for an emergency call.
8: The network is lost.
9: Audio ON.
10: Show reload status of each SIM phonebook after init phase (after Power-ON or SIM
insertion).
11: Show the checksum of Sim phonebooks after loading them
12: An interruption has occurred
The AT+WIND? command is supported and indicates the <allowed bit flows>. AT+WIND
settings are automatically stored in non volatile memory (EEPROM). This means the &W
command does not need to be used and the selected flows are always activated after boot.
Default value is 0: no flow activated, no indication.
AT+WIND=? gives the possible value range (0-1023)
The unsolicited response will then be:
+WIND : <event> [ ,<idx> ]
<idx>
Call identifier, defined in +CLCC command.
Or for event 10:
+WIND: <event>,<phonebook>,<status>,…,<phonebook>,<status>
<phonebook>
SIM phonebook (“SM”, “FD”, “ON”, “SN”, “EN”)
<status>
0: Not Reloaded from SIM (no change since last init or SIM remove)
1: Reloaded from SIM to internal memory (at least one entry has changed)
Or for event 11:
+WIND: <event>,[“<checksum of SM>”],[“<checksum of FD>”],[“<checksum of
ON>”],[“<checksum of SN>”] ,[“<checksum of EN>”],[“<checksum of LD>”]
<checksum>
128-bit “fingerprint” of the phonebook.
NOTE: If the service of the phonebook is not loaded or not present, the checksum is not displayed and
two comas without checksum are displayed (,,).

125
15.4 Analog digital converters measurements +ADC

15.4.1 Description:
This command gets the (DC level * 1024) of ADC A and ADC B (these voltages are coded
on 10 bits, see hardware specifications) or the (DC level * 1024) of ADC A, ADC B and ADC
C (voltages coded on 10 bits) depending on the ADC mode.
For ADC A, the value returned includes the resistor bridge. These values are updated every
10 seconds.
This command allows ADC mode to be set. Mode 0 displays the values of the first 2
converters on 10 bits, mode 1 also displays the values of the 3 converters coded on 10 bits.

15.4.2 Syntax:
Command Syntax: AT+ADC
COMMAND POSSIBLE RESPONSES
AT+ADC=<n>
AT+ADC=0 OK
Note: Select 2 converters (mode 0) Note: 2 converters mode selected
AT+ADC=1 OK
Note: Select 3 converters (mode 1) Note: 3 converters mode selected
AT+ADC=? +ADC: (0-1)
Note: Ask for the list of possible values Note: possible values 0 or 1
AT+ADC? +ADC: 500,412
OK
Note: Ask for the current values of converters in mode 0 Note: Adc A, Adc B on 10 bits
AT+ADC? +ADC: 712,698,997
OK
Note: Ask for the current values of converters in mode 1 Note: Adc A, Adc B, Adc C on 10 bits

126
15.5 Mobile Equipment event reporting +CMER

15.5.1 Description:
This command enables or disables sending of unsolicited result codes in the case of a key
press.

15.5.2 Syntax:
Command Syntax: AT+CMER=<mode>,<keyp>,<disp>,<ind>,<bfr>
The parameters <mode>, <disp>, <ind> and <bfr> are not handled.

15.5.3 Defined values:


<keyp> (keypad):
0: No keypad event reporting.
1: Keypad event reporting are routed using unsolicited
code : +CKEV : <key>, <press>

<press>
1: key press
0: key release

<key> : Keyboard map is (5,5)

0 1 2 3 4
5 6 7 8 9
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24

15.6 Read Language Preference +WLPR

15.6.1 Description:
Read a Language Preference value of EF-LP. The first indices should have the highest
priority.

15.6.2 Syntax:
Command syntax: AT+WLPR= <index >
Response syntax: +WLPR: <value>
COMMAND POSSIBLE RESPONSES
AT+WLPR? +WLPR: 4
OK
Note: Read command Note: Four language preferences are available in EF-LP
AT+WLPR=1 +WLPR: 5
OK
Note: Read first EF-LP index value Note: Language preference is 5

127
15.7 Write Language Preference +WLPW

15.7.1 Description:
Write a Language Preference value in EF-LP

15.7.2 Syntax:
Command syntax: AT+WLPW=<index >,<value>
Response syntax: OK or +CME ERROR: <err>
COMMAND POSSIBLE RESPONSES
AT+WLPW=1,5 OK
Note: Write Lang Pref equal to 5 in EF-LP with index 1 Note: EF-LP correctly updated

15.8 Read GPIO value +WIOR

15.8.1 Description:
Read the requested GPI or GPIO pin value.
NOTE: by default (e.g. after a reset), the I/O ports configuration is set by the +WIOM command.
NOTE: This command is allowed only on a Gpio not allocated by an Open-AT embedded application or
for I2C soft bus.

15.8.2 Syntax:
Command syntax: AT+WIOR=<index>
Response syntax: +WIOR: <value>
COMMAND POSSIBLE RESPONSES
AT+WIOR=0 +WIOR: 0
Read I/O (number 0) value OK
GPIO number 0 is reset

15.8.3 Defined values:


<index>
Eight I/O ports are available. The <index> value is between 0 and 7.

<value>
0: I/O port number <index> is reset.
1: I/O port number <index> is set.

128
15.9 Write GPIO value +WIOW

15.9.1 Description:
Set the requested GPO or GPIO pin value.

NOTE: by default (after a reset), the I/O ports configuration is set by the +WIOM command.
NOTE: This command is allowed only on a Gpio not allocated by the Open-AT embedded application
or for I2C soft bus.

15.9.2 Syntax:
Command syntax: AT+WIOW=<index >,<value>
COMMAND POSSIBLE RESPONSES
AT+WIOW=2,0 OK
Reset I/O (number 2) GPIO value is written

15.9.3 Defined values:


<index>
Eight I/O ports are available. The <index> value is between 0 and 7.
<value>
0: I/O port number <index> is reset.
1: I/O port number <index> is set.

15.10 Input/Output Management +WIOM

15.10.1 Description:
This specific command allows to set the default GPIOs configuration (input or output) after
reset, and each GPIO default value (if set as an output) after reset.
NOTE: This command is allowed only on a Gpio not allocated by the Open-AT embedded application
or for I2C soft bus.

15.10.2 Syntax:
Command Syntax AT+WIOM=[<GpioDir>],[<GpioVal>]
COMMAND POSSIBLE RESPONSES
AT+WIOM? +WIOM: 255,0
OK
On reset, all GPIOs are set to 0, as an output.
AT+WIOM=? +WIOM: (0-255),(0-255)
OK
Range allowed for the parameters.
AT+WIOM=254 OK
Set GPIO 0 as an input, and all others as outputs.
AT+WIOM=,128 OK
Set GPIO 7 default output value to 1.
AT+WIOM? +WIOM: 254,128
OK

129
15.10.3 Defined values:
<GpioDir>
Bit table parameter.
Allowed range : [0 ; 255],
Default value : 255 (all GPIOs set as outputs).
Each bit gives the corresponding GPIO default direction : 0 for input, 1 for output.

<GpioVal>
Bit table parameter.
Allowed range : [0 ; 255],
Default value : 0 (all GPIOs reset to 0).
Each bit gives the corresponding GPIO default value.
If it is set as an output : 0 for reset, 1 for set.
The GPIOs set as inputs by the <GpioDir> parameter are not affected by the value set by
the <GpioVal> parameter.
NOTES:
❑ <GpioDir> bit values for GPI and GPO are ignored.
❑ <GpioVal> bit values for GPI are ignored.
❑ Here is the corresponding table between Module Gpio Pin Names and AT commands
numbers:

AT Commands number Wismo Quik Pin Names Wismo Pac Pin Names
0 GPIO 0 GPIO 0
1 GPO 1 GPI
2 GPO 2 GPIO 2
3 GPI GPIO 3
4 GPIO 4 GPIO 4
5 GPIO 5 GPIO 5
6 (no gpio affected) (no gpio affected)
7 (no gpio affected) (no gpio affected)

130
15.11 Abort command +WAC

15.11.1 Description:
This specific command allows SMS, SS and PLMN selection related commands to be
aborted.

15.11.2 Syntax:
Command syntax: AT+WAC
COMMAND SYNTAX RETURN
AT+WAC
AT+WAC=? OK
AT+WAC? OK

Example :
COMMAND POSSIBLE RESPONSES
AT+COPS=?
Note: Available PLMN
AT+WAC OK
Note: Abort the request of PLMN list Note:

15.12 Play tone +WTONE

15.12.1 Description:
This specific command allows a tone to be played on the current speaker or on the buzzer.
Frequency, gain and duration can be set.

15.12.2 Syntax:
Command syntax: AT+WTONE=<mode>[,<dest>,<freq>,<gain>,<duration>]
Response syntax: OK or +CME ERROR: <err>
COMMAND POSSIBLE RESPONSES
AT+WTONE=1,1,300,9,50 OK
Note: Play a tone Note: Done
AT+WTONE=0 OK
Note: Stop playing Note: Done
AT+WTONE=? OK
Note: Test command Note: Done
AT+WTONE? ERROR
Note: Current value Note:

131
15.12.3 Defined values:
<mode>
0: Stop playing.
1: Play a tone

<dest>
This parameter sets the destination (mandatory if <mode>=1)
<dest>
1: Speaker
2: Buzzer

<freq>
This parameter sets tone frequency (in Hz) (mandatory if <mode>=1). If <dest> is the
speaker, the range is between 1Hz and 3999Hz. If <dest> is the buzzer, the range is between
1Hz and 50000Hz.

<gain>
0-15: This parameter sets the tone gain. The default value is 9.

<gain> Speaker (db) Buzzer (db)


0 0 -0.25
1 -0.5 -0.5
2 -1 -1
3 -1.5 -1.5
4 -2 -2
5 -3 -3
6 -6 -6
7 -9 -9
8 -12 -12
9 -15 -15
10 -18 -18
11 -24 -24
12 -30 -30
13 -36 -40
14 -42 -infinite
15 -infinite -infinite

<duration>
0-50: This parameter sets tone duration (unit of 100 ms). When this parameter is equal to 0
(default value), the duration is infinite, and the tone can be stopped by AT+WTONE=0.

132
15.13 Play DTMF tone +WDTMF

15.13.1 Description:
This specific command allows a DTMF tone to be played on the current speaker. DTMF,
gain and duration can be set.
This command is only used to play a DTMF tone. To send a DTMF over the GSM network,
use the +VTS command.

15.13.2 Syntax:
Command syntax: AT+WDTMF=<mode>[,<dtmf>,<gain>,<duration>]
Response syntax: OK or +CME ERROR: <err>
COMMAND POSSIBLE RESPONSES
AT+WDTMF=1,"*",9,100 OK
Note: Play a DTMF tone Note: Done
AT+WDTMF=0 OK
Note: Stop playing Note: Done
AT+WDTMF=? +WDTMF: (0-1),(0-9,*,#,A,B,C,D),(0-15),(0-50)
Note: Test command OK
Note: Done
AT+WDTMF? ERROR
Note: Current value Note:

15.13.3 Defined values:


<mode>
0: Stop playing.
1: Play a DTMF tone

<dtmf>
This parameter sets the DTMF to play in {0-9,*,#,A,B,C,D} (mandatory if <mode>=1)

<gain>
0-15: This parameter sets tone gain. The values are identical to those of the +WTONE
(speaker) command. By default, the value is 9.

<duration>
0-50: This parameter sets the tone duration (unit of 100 ms). When this parameter is 0
(default value), the duration is infinite, and the DTMF tone can be stopped by
AT+WDTMF=0.

133
15.14 Wavecom Downloading +WDWL

15.14.1 Description:
This specific command switches the product to download mode.
Downloading is performed using the 1K-XMODEM protocol.

15.14.2 Syntax:
Command syntax: AT+WDWL
COMMAND POSSIBLE RESPONSES
AT+WDWL +WDWL: 0
Note: Switch on downloading mode Note: Start the downloading

Note: Downloading in progress
AT+CFUN=1
Note: Reset the product at the end
OK
Note:

134
15.15 Wavecom Voice Rate +WVR

15.15.1 Description:
This specific command allows the voice rate for bearer voice to be configured (available
for outgoing calls only).

15.15.2 Syntax:
Command Syntax: AT+WVR=<n>
COMMAND SYNTAX RETURN
AT+WVR=<n>
AT+WVR=? If Half Rate available.
+WVR: (0,2,3)
If EFR available.
+WVR: (0,1)
If HR and EFR not available
+WVR: (0)
If HR and EFR available
+WVR: (0-5)
AT+WVR? +WVR: <n>

COMMAND POSSIBLE RESPONSES


AT+WVR=1 OK
Note: Configure voice type FR and EFR Note: Bearer is configured
AT+WVR=6 +CME ERROR: 3
Note:
Syntax error
AT+WVR? +WVR: 1
OK
Note: Ask the current value Note:
OK
Note:

15.15.3 Defined values:


<n>
Voice coding type.
<n>
0: FR
1: FR and EFR
2: FR, HR with HR preferred
3: HR, FR with FR preferred
4: EFR,HR with HR preferred
5: HR,EFR with EFR preferred.

135
15.16 Data Rate +WDR

15.16.1 Description:
This specific command allows the data rate for bearer data to be configured (available for
outgoing calls only).

15.16.2 Syntax:
Command Syntax: AT+WDR=<n>
COMMAND SYNTAX RETURN
AT+WDR=<n>
AT+WDR=? If Half Rate available.
+WDR: (0-2)
Else
+WDR: (0)
AT+WDR? +WDR: <n>

COMMAND POSSIBLE RESPONSES


AT+WDR=1 OK
Note: Configure voice type FR,HR with HR prefered. Note: Bearer is configured
AT+WDR=3 +CME ERROR: 3
Syntax error Note:
AT+WDR? +WDR: 1
Note: Ask the current value OK
Note:
OK
Note:

15.16.3 Defined values:


<n>
Data coding type.
<n>
0: FR
1: FR, HR with HR preferred
2: HR, FR with FR preferred

136
15.17 Hardware Version +WHWV

15.17.1 Description:
This specific command gets the hardware version.

15.17.2 Syntax:
Command Syntax: AT+WHWV
COMMAND POSSIBLE RESPONSES
AT+WHWV Hardware Version 4.14
OK
Note: Request Hardware Version Note: Hardware version is 4.14
AT+WHWV Hardware Version -.--
OK
Note: Request Hardware Version Note: No hardware version available

15.18 Date of Production +WDOP

15.18.1 Description:
This specific command gets the date of production. Format of the date is Week/Year.

15.18.2 Syntax:
Command Syntax: AT+WDOP
COMMAND POSSIBLE RESPONSES
AT+WDOP Production date (W/Y): 01/2000
OK
Note: Request Date of Production Note: Date of production is WEEK: 01 / YEAR: 2000 (1st
week of year 2000)
AT+WDOP Production date (W/Y): --/----
OK
Note: Request Date of Production Note: No date of production available

137
15.19 Wavecom Select Voice Gain +WSVG

15.19.1 Description:
The product has 2 voice gain controllers, this specific command allows the microphone
gain controller to be selected.

15.19.2 Syntax:
Command Syntax: AT+WSVG = <n>
COMMAND POSSIBLE RESPONSES
AT+WSVG=<n>
AT+WSVG=0 OK
Note: Select Controller 1 (Default) Note: Controller 1 selected
AT+WSVG=1 OK
Note: Select Controller 2 (Default) Note: Controller 2 selected
AT+WSVG=? +WSVG: (0-1)
Note: Get the list of possible values Note: possible values 0 or 1
AT+WSVG? +WSVG: 1
Note: Get the current value Note: Controller 1 is selected

15.19.3 Defined values:


<n> Controller
0: Controller 1 (Default)
1: Controller 2

138
15.20 Wavecom Status Request +WSTR

15.20.1 Description:
This specific command returns some operation status. It can be used for ex. to check the
state of the initialisation sequence; the different values returned are Not started, Ongoing,
Finished.

15.20.2 Syntax:
Command syntax: AT+WSTR=<status>
Response syntax: +WSTR: <status>,<value>
COMMAND POSSIBLE RESPONSES
AT+WSTR=<status> +WSTR :<status>,<value>
AT+WSTR=1 +WSTR: 1,2
OK
Note: Select the status 1 (INIT SEQUENCE) Note: Init finished
AT+WSTR=2 +WSTR: 2,1
OK
Note: Select the status 2 (NETWORK STATUS) Note: The network is available
AT+WSTR=? +WSTR: (1-2)
Note: Ask the list of possible values +WSTR: (1-2)Note: possible values: 1, 2

15.20.3 Defined values:


<status>
1: Initialisation sequence

<value>
0: Not started
1: On going
2: Finished

<status>
2: Network status

<value>
0: No network
1: Network available

15.21 Wavecom Scan +WSCAN

15.21.1 Description:
This specific command displays the received signal strength indication (<rssi>) for a
specified frequency (in absolute format).

This command is not allowed during communication.

139
15.21.2 Syntax:
Command syntax: AT+WSCAN=<absolute frequency>
Response syntax: +WSCAN: <rssi>
COMMAND POSSIBLE RESPONSES
AT+WSCAN=50 +WSCAN: 23
OK
Note: Request <rssi> of absolute frequency 50 Note: <rssi> is 23.
AT+WSCAN=1025 CME ERROR: 3
Note: Request power of absolute frequency 1025 Note: 1025 is not a valid absolute frequency

15.21.3 Defined values:


<absolute frequency>
frequency in absolute format

<rssi>
0: -113 dBm or less
1: -111 dBm
2...30: -109 to -53 dBm
31: -51dBm or greater
99: not known or not detectable

15.22 Wavecom Ring Indicator Mode +WRIM

15.22.1 Description:
This specific command sets or returns the state of the Ring Indicator Mode.
In pulse RI mode, an electrical pulse is sent on the Ring Indicator signal just before sending
any unsolicited AT response in order not to lose AT responses when client tasks are in
sleep state. Still in RI mode, when receiving incoming calls, electrical pulses are sent on
the RI signal.
In up-down RI mode, no pulses are sent before unsolicited AT response, and up-down
signals are sent when receiving an incoming call.

15.22.2 Syntax:
Command syntax: AT+WRIM=<n>
COMMAND POSSIBLE RESPONSES
AT+WRIM=<n>
AT+WRIM=0 OK
Note: Select up-down RI mode Note: up-down RI mode selected
AT+WRIM=1 OK
Note: Select pulse RI mode Note: pulse RI mode selected
AT+WRIM=? +WRIM: (0-1)
Note: Ask the list of possible values Note: possible values 0 or 1
AT+WRIM? +WRIM: 1
Note: Ask the current value Note: current RI mode is pulse RI.

140
15.22.3 Defined values:
<n>
0: up-down RI mode
1: pulse RI mode

15.23 Wavecom 32kHz Power down Mode +W32K

15.23.1 Description:
This specific command allows the 32kHz power down mode to be enabled or disabled.
When power down mode is entered, the product uses a 32kHz internal clock during
inactivity stages.
When enabled, power down mode is active after 1 to 15 minutes.
For additional information on power down mode, see Appendix F.

15.23.2 Syntax:
Command Syntax: AT+W32K=<mode>
COMMAND POSSIBLE RESPONSES
AT+W32K=1 OK
Note: Enable 32kHz power down mode Note: 32kHz power down mode is enabled
AT+W32K=0 OK
Note: Disable 32kHz power down mode Note: 32kHz power down mode is disabled

15.23.3 Defined values:


<mode>
0: Disable 32kHz powerdown mode
1: Enable 32kHz powerdown mode

15.24 Wavecom Change Default Melody +WCDM

15.24.1 Description:
This specific command allows a manufacturer specific melody to be selected. This default
melody will be played for any new incoming voice call, either on the buzzer or on the
speaker. If melody 0 is selected, no melody will be played.

141
15.24.2 Syntax:
Command Syntax: AT+WCDM=<melody>,<player>
COMMAND POSSIBLE RESPONSES
AT+WCDM=0 OK
Note: Select no melody
AT+WCDM=5 OK
Note: Select melody n°5
AT+WCDM? +WCDM: 5,0
Note: Indicate the current melody OK
Note: Melody n°5 is currently selected, and the buzzer is
selected to play it.
RING
Note: An incoming call occurs, and the melody n°5 is played
on the buzzer.
AT+WCDM=,1 OK
Note: Select the speaker to play the melody on.
AT+WCDM? +WCDM: 5,1
OK
Note: Now the speaker is selected to play the melody if an
incoming call occurs.

15.24.3 Defined values:


<melody>
0: No melody (default)
2...10: Melody 1 to 10

<player>
0: Melody n°<melody> will be played on the buzzer for any new incoming voice call. (default)
1: Melody n°<melody> will be played on the speaker for any new incoming voice call.

15.25 Wavecom Software version +WSSW

15.25.1 Description:
This specific command displays some internal software reference.

15.25.2 Syntax:
Command Syntax: AT+WSSW
COMMAND POSSIBLE RESPONSES
AT+WSSW A00_00gm.2c 000000008F5DC6EA
OK
Note: Get Software version Note: internal software information

142
15.26 Wavecom Custom Character Set +WCCS

15.26.1 Description:
This specific command allows to edit and display the custom character set tables. The
“CUSTOM” mode of +CSCS and the +WPCS commands use this character set. In this
mode, when the user enters a string, this string is converted into GSM alphabet using the
Custom To GSM table. In a similar way, when the user requests a string display, the string
is converted from GSM alphabet using the GSM To Custom table.
In edition mode, the edition session is terminated by <ctrl-Z>, or aborted by <ESC>. Only
hexadecimal characters (‘0’…’9’, ‘A’…’F’) can be used. The number of characters entered
must equal the edition range requested, otherwise the command will terminate with a
“+CME ERROR: 3” result.

15.26.2 Syntax:
Command Syntax: AT+WCCS=<mode>,<table>,<char 1>[,<char 2>]
COMMAND POSSIBLE RESPONSES
AT+WCCS=0,0,120,130 +WCCS: 11,
78797A2020202020097E05
Note: Display from character 120 to character 130 OK
of the Custom To GSM conversion table Note: 11 characters displayed
AT+WCCS=1,0,115<CR> OK
20<ctrl-Z> Note: Edition successful
Note: Edit character 115 of the Custom To GSM
conversion table
AT+WCCS=1,1,0,4<CR> OK
40A324A5E8<ctrl-Z> Note: Edition successful
Note: Edit the 5 first characters of the GSM
To Custom conversion table
AT+WCCS=1,1,200 +CME ERROR: 3
Note: Edit character 200 of GSM Note: Index out of range
To Custom conversion table

15.26.3 Defined values


<mode>
0: Display the table
1: Edit the table

<table>
0: Custom To GSM conversion table
1: GSM To Custom conversion table

<char 1>, <char 2>Character range to display/edit. If only <char 1> is present, only this char
is displayed/edited.
0…127: for GSM To Custom conversion table
0…255: for Custom To GSM conversion table
See section 19.2 for informative examples on phonebooks.

143
15.27 Wavecom LoCK +WLCK

15.27.1 Description:
This specific command allows the ME to be locked on a specific network operator.
NOTE: Test SIM cards (with MCC=001 & MNC=01) doesn’t check these locks.

15.27.2 Syntax:
Command syntax: AT+WLCK=<fac>,<passwd>,<NetId>[,<GID1>[,GID2]]
[,<CnlType>[,<CnlData>]]
Response syntax: +WLCK: <status>
COMMAND POSSIBLE RESPONSES
AT+WLCK="PN",12345678,20810 OK
Note: Activate network lock on SFR (208,10) Note: Network lock activated
AT+WLCK="PS",12345678,208105923568974 OK
Note: Activate SIM lock Note: SIM lock activated
AT+WLCK="PU",12345678,2081035 OK
Note: Activate Network Subset lock on SFR (208, 10, 35). Note: Network Subset lock activated
AT+WLCK="PU",12345678,20810 +CME ERROR: 3
Note: Need 7 digits of IMSI to perform a service provider lock
AT+WLCK=”PP”,12345678,20810,”E5” OK
Note: Activate Service Provider lock on
SFR (208, 10) and GID1 (0xE5). Note: Service Provider lock activated.
AT+WLCK=”PC”,12345678,20810,”E5”,”10” OK
Note: Activate Corporate lock on SFR (208, 10),
GID1 (0xE5) and GID2 (0x10). Note: Corporate lock activated.
AT+WLCK=”PN”,12345678,20810,0 OK
Note: Activate Network lock on SFR (208, 10) Note: Network lock activated on SFR and co-operative
using co-operative network list from SIM file EFCNL network list present in SIM
(must be present in SIM)
AT+WLCK=”PN”,12345678,20801,1,
”02F802FFFFFF02F801FFFFFF” OK
Note: Activate Network lock on F ORANGE (208, 01) Note: Network lock activated on F ORANGE
with manual co-operative network list including (primary network), SFR and Bouygues Telecom
SFR (208, 10) and Bouygues Telecom (208, 20) (co-operative networks)

The following <fac> values are supported:


“PS”: SIM lock facility with a 8 digits password (PCK).
“PN”: Network lock with a 8 digits password (NCK).
“PU”: Network subset lock with a 8 digits password (NSCK).
“PP”: Service provider lock with a 8 digits password (SPCK).
“PC”: Corporate lock with a 8 digits password (CCK).

<CnlType> Type of lock for co-operative network list (CNL)


0: Automatic (co-operative network list retrieved from EFCNL SIM file)

144
NOTE: EFCNL file must be present in SIM to use automatic mode.
1: Manual (co-operative network list is given in the <CnlData> parameter)

<CnlData>
Co-operative network list (hexa string type) using same format as in EFCNL SIM file (ETSI
GSM 11.11 or 3GPP 04.08).

NOTE: Only if <CnlType> = 1

15.28 CPHS command +CPHS

15.28.1 Description:
This specific command is used to activate, deactivate or interrogate a CPHS feature (e.g.
Voice Mail Indicator, Mail Box Number…)

NOTE: This command may answer +CME ERROR: 3 if the CPHS feature is disabled (cf. +WFM
command), or if the SIM card does not support this CPHS feature.

15.28.2 Syntax
Command Syntax: AT+CPHS=<Mode>,<FctId>
COMMAND POSSIBLE RESPONSES
AT+CPHS=<Mode>,<FctId> OK
+CME ERROR: 3
+CPHS: <FctId1>,<Status><CR<LF>
+CPHS: <FctId2>,<Status><CR<LF>
AT+CPHS? …
+CPHS: <FctIdn>,<Status><CR<LF>
OK
AT+CPHS=? OK

15.28.3 Defined values:


<Mode>
0: Deactivate a CPHS feature
1: Activate a CPHS feature
2: Interrogate a CPHS status

<FctId>
1: Voice Mail Indicator
2: Mail Box Number

<Status>
0: CPHS feature disabled
1: CPHS feature enabled

145
15.29 Unsolicited result : Wavecom Voice Mail Indicator +WVMI

15.29.1 Description:
This unsolicited indication gives the status of the LINE 1, LINE 2, FAX or DATA mailbox.

Syntax: +WVMI: <LineId>,<Status>


Option :
<LineId>
1: Line 1
2: Line 2
3: FAX
4: DATA

<Status>
0: No message waiting.
1: At least one message is waiting

15.29.2 Example:

AT+CPHS? Interrogate the status of CPHS functionality


+CPHS: 1,0 The voice mail indicator functionality is deactivated
+CPHS: 2,0 The mail box number functionality is deactivated
OK

AT+CPHS=3,1 Syntax error


+CME ERROR: 3

AT+CPHS=1,1 Activate the voice mail indicator functionality


OK

AT+CPHS? Interrogate the status of CPHS functionality


+CPHS: 1,1 The voice mail indicator functionality is activated
+CPHS: 2,0 The mail box number functionality is deactivated
OK

**** the message box contains 1 message *****


+WVMI: 1,1 A message is waiting on Line 1
***** The message box contains a second message ***
+WVMI: 2,1 A message is waiting on Line 2

AT+CPHS=2,1 Interrogate the status of voice mail indicator functionality


+WVMI: 1,1 a message is waiting on LINE 1
+WVMI: 2,1 a message is waiting on LINE 2
+WVMI: 3,0 no FAX waiting
+WVMI:4,0 no data waiting

AT+CPHS=1,2 Activate the mail box number functionality


OK

146
AT+CPHS? Interrogate the status of CPHS functionality
+CPHS: 1,1 The voice mail indicator functionality is activated
+CPHS: 2,1 The mail box number functionality is activated
OK
AT+CPHS=2,2 Query current mail box numbers in SIM
+WMBN: 1,"19254871234",129,1 Mail box number for Line 1
+WMBN: 2,,,0 Mail box number for Line 2
+WMBN: 3,,,0 Mail box number for Fax Line
+WMBN: 4,,,0 Mail box number for Data Line
OK Only Line1 can be updated

147
15.30 Wavecom Battery Charge Management +WBCM

15.30.1 Description:
This specific command allows the battery charging to be managed (start and stop the
charge, enable or disable unsolicited +WBCI Battery Charge Indications), and sets the
battery charge parameters.

15.30.2 Syntax:
Command Syntax: AT+WBCM=<Mode>[,[<ChargeInd>][,[<BattLevelMax>],
[<BattLevelMin>],[<TPulseInCharge>],
[<TPulseOutCharge>],[<BattIntRes>]]]
COMMAND POSSIBLE RESPONSES
AT+WBCM=0 OK
Stop the battery charging.
AT+WBCM=1,1 OK
Start the battery charging with charge indications.
+WBCI: 2,4060
Unsolicited charge indication: the current battery
voltage is 4.06 V. See +WBCI description.
AT+WBCM=1,0 OK
Start the battery charging without charge indications.
AT+WBCM=2 +WBCI: 2,4110
Get the battery voltage during the charging. OK
See the description of +WBCI unsolicited response. The
current battery voltage is 4.11 V.
+WBCI: 1
The battery voltage has reached the max level. The battery is
considered as charged and the charging is stopped.
AT+WBCM? +WBCM: 0,0,4200,3300,100,5000,0
OK
Current values.
AT+WBCM=0,1 OK
Enable the battery charge unsolicited indications
out of charge.
+WBCI: 3,4195
The current battery voltage is 4.195 V.
AT+WBCM=3,0,3800,3000,500,3000,0 OK
Configure the battery charging parameters.
AT+WBCM=? +WBCM: (0-3),(0-1),(4000-5000),(2800-3800), (100-
Get the parameters range 10000),(100-10000),(0-255)
. OK
+WBCI: 0
The battery voltage has reached the min level. The battery is
considered as discharged, and the product is turned off, as
for the +CPOF command behavior.

148
15.30.3 Defined values:
<Mode>
0: Stop the battery charging (default).
1: Start the battery charging.
2: Get the current battery voltage.
3: Set the battery charge parameters.

NOTE: When <Mode> equals 0 or 1, only the <ChargeInd> parameter can be set; <Mode> 2 does not
allow any additional parameter to be set; <Mode> 3 allows all others parameters to be set.

<ChargeInd>
0: Disable the battery charge unsolicited indications (default).
1: Enable the battery charge unsolicited indications (see +WBCI description).

<BattLevelMax>
Maximum level for the battery voltage. When reached, the battery is considered as
charged.
The allowed range is [4000 ; 5000] (in mV, default value is 4200)

<BattLevelMin>
Minimum level for the battery voltage. When reached, the battery is considered as
discharged, and the product is turned off (as with the +CPOF command behavior).
The allowed range is [2800 ; 3800] (in mV, default value is 3300)

NOTE: The <BattLevelMax> and <BattLevelMin> parameters cannot be changed during the battery
charging (when <Mode> = 1).

<TPulseInCharge>
Time between pulses for the pulsed charge. The pulse duration lasts one second. When
the battery charging is started with unsolicited charging indications (<ChargeInd> = 1),
+WCBI responses are returned by the ME with a (<Pulse Time> (= 1s) + <TPulseInCharge>)
period. The allowed range is [100 ; 10000]. (in ms, default value is 100).

<TPulseOutCharge>
Time between +WBCI unsolicited responses, when the battery charge is stopped with
charging indications requested (<ChargeInd> = 1). The allowed range is [100 ; 10000]
(in ms, default value is 5000).

<BattIntRes>
Battery Internal Resistor. This parameter must be set to have correct values with +WBCI
unsolicited results.
The allowed range is [0 ; 255] (in mΩ, default value is 0)

NOTE: When the <BattIntRes> parameter is changed, the product must be reset to take the
modification into account.

149
15.30.4 Unsolicited result : Wavecom Battery Charge Indication +WBCI

15.30.4.1 Description:
This unsolicited indication returns information about the battery charge (Maximum Level
reached, current battery voltage, etc).
15.30.4.2 Syntax:
Unsolicited response Syntax: +WBCI: <Status>[,<BattLevel>]
15.30.4.3 Defined values:
<Status>
0: Minimum battery level reached - the battery is considered as discharged. The product
is turned off (as with the +CPOF command).
1: Maximum battery level reached - the battery is considered as charged. The battery
charging is stopped.
2: Battery currently in charge.
3: Battery currently out of charge.

NOTE: <Status> 2 and 3 are solicited by the AT+WBCM=2 command, or unsolicited when the
<ChargeInd> parameter of the +WBCM command is set to 1. With these <Status> values, the
<BattLevel> parameter is also present.

<BattLevel>
Current battery voltage during or out of the charging.
The possible range is [2800 ; 5000]. (in mV)

150
15.31 Features Management +WFM

15.31.1 Description:
This specific command allows some features to be enabled or disabled.

NOTE: After a modification, the changes will be taken into account only after a reset of the product.

15.31.2 Syntax:
Command syntax: AT+WFM=<mode>[,<FtrID>]
Response syntax: +WFM: <FtrID>,<status>,<resetFlag>
COMMAND POSSIBLE RESPONSES
AT+WFM=2,”BI9001800” +WFM: “BI9001800”,1,0
OK
Dual-band mode 900/1800 is enabled
AT+WFM=1,11 OK
Enable the Mono-band 900 mode
AT+WFM=0,61 +CME ERROR: 3
<mode> 0 is not allowed on <FtrID> values with 2 digits
AT+WFM=0,”EFR” OK
Disable the Enhanced Full Rate feature
AT+WFM=2 +WFM: "MONO900",1,1
Interrogate all <FtrID> status +WFM: "MONO1800",0,0
+WFM: "MONO1900",0,0
+WFM: "BI9001800",0,1
+WFM: "BI9001900",0,0
+WFM: "EFR",0,1
+WFM: "NOHR_NOECHO",0,0
+WFM: "HR",1,0
+WFM: "ECHO",0,0
+WFM: "DTXDATA",1,0
+WFM: "DATA144",1,0
+WFM: "SIM3VONLY",0,0
+WFM: "SIM5VONLY",0,0
+WFM: "SIM3AND5V",1,0
+WFM: "SIMREMOVE",1,0
+WFM: "NOINTERRUPT",0,0
+WFM: "QUICKOFF",0,0
+WFM: "OFFWHENUNPLUG",0,0
+WFM: "INTERRUPT",1,0
+WFM: "SWITCHATT",1,0
+WFM: "CPHS",1,0
+WFM: "SIMSPEEDENH",0,0
+WFM: "LOCA",0,0
OK
The modified features have their <resetFlag> parameter set to 1

151
15.31.3 Defined values:
<mode>
0: disable feature <FtrID>
1: enable feature <FtrID>
2: interrogate the status of the <FtrID> feature. If the <FtrID> parameter is not used, all
features’ status are listed with several +WFM responses.
<FtrID>
11 or "MONO900": Mono-band mode 900 MHz (def. 0)
12 or "MONO1800": Mono-band mode 1800 MHz (def. 0)
13 or "MONO1900": Mono-band mode 1900 MHz (def. 0)
14 or "BI9001800": Dual-band mode 900/1800 MHz (def. 1)
15 or "BI9001900": Dual-band mode 900/1900 MHz (def. 0)
2 or "EFR": Enhanced Full Rate feature (def. 1)
32 or "HR": Half Rate feature (def. 1)
33 or "ECHO": Echo Cancel (def. 0)
4 or "DTXDATA": Data with DTX feature (def. 1)
5 or "DATA144": Data 14.4 kbit/s feature (def. 1)
61 or "SIM3VONLY": 3V SIM voltage mode (def. 0)
62 or "SIM5VONLY": 5V SIM voltage mode (def. 0)
63 or "SIM3AND5V": Both 3 and 5V SIM voltage mode (def. 1)
7 or "SIMREMOVE": SIM removal feature (def. 1)
81 or "NOINTERRUPT": No management of interruption (def. 0)
82 or "QUICKOFF": Quick Off mode (def. 0)
83 or "OFFWHENUNPLUG": Off when unplug mode (def. 0)
84 or "INTERRUPT": interruption for customer (def. 1)
9 or "SWITCHATT": Switch Attenuation feature (def. 1)
A or "CPHS": CPHS feature (def. 1)
B or "SIMSPEEDENH": SIM speed enhancement feature (def. 0)
C or "LOCA": Location feature (def. 0)

NOTE 1: The +WFM response only use alphabetical values for the <FtrID> parameter.
NOTE 2 : For <FtrID> values with two digits (like 1x, 6x or 8x), the <mode> 0 value is not allowed.
When a « xa » feature is enabled, enabling an other « xb » feature will automatically disable the « xa »
feature.
For example, if the "MONO900" feature is enabled, if the "BI9001800" feature is activated, the
"MONO900" feature gets automatically disabled.
Likewise, the "HR" feature and the "ECHO" feature are exclusive.
If “NOHR_NOECHO” is activated, both features “HR” and “ECHO” are disabled.

<status>
0: the <FtrID> feature is disabled
1: the <FtrID> feature is enabled

152
<resetFlag>
0: the feature has not been modified since the last boot of the product.
1: the feature has been modified since the last boot of the product; the product has to be
reset in order to take the modification into account.

NOTE: If a feature is reset to its initial value after a modification, the <resetFlag> parameter will be
reset to 0.

15.32 Commercial Features Management +WCFM

15.32.1 Description:
This command allows Wavecom specific features to be enabled or disabled. Disabling a
feature can be done with no restriction, but a password is required to enable one (or more)
features.

NOTE: Once a feature successfully enabled or disabled, the product needs to be reset to take the
modification into account.

15.32.2 Syntax:
Command syntax: AT+WCFM=<mode>,<FtrMask>[,<Password>]
COMMAND POSSIBLE RESPONSES
AT+WCFM=? OK
AT+WCFM=0,”0A00” OK
Disable some features
AT+WCFM=1,”0003”,”1234567890ABCDEF12345 OK
67890ABCDEF1234567890ABCDEF1234567890 The features are enabled (the password is correct)
ABCDEF”
Enable features
AT+WCFM=1,”0050”,”1234567890ABCDEF +CME ERROR: 3
1234567890ABCDEF1234567890ABCDEF Incorrect password
1234567890ABCDEF”
Enable features

15.32.3 Defined values:


<mode>
0: disable some features of <FtrMask>
1: enable some features of <FtrMask>

<FtrMask>
16 bits hexadecimal string (4 characters from 0 to F)

<PassWord>
256 bits hexadecimal string (64 characters from 0 to F)

153
15.33 Wavecom Customer storage mirror +WMIR

15.33.1 Description:
This specific command allows to make a mirror copy of the current configuration
parameters. In case of memory problem for the storage, if a customer mirror already
exists, this one will be restored. Otherwise, the Wavecom default mirrored parameters are
restored.

15.33.2 Syntax:
Command syntax: AT+WMIR
COMMAND POSSIBLE RESPONSES
AT+WMIR=? OK
AT+WMIR OK
Build the Customer Mirror

15.34 Wavecom Change Default Player +WCDP

15.34.1 Description:
This specific command allows the default melody player to be selected.

15.34.2 Syntax:
Command syntax: AT+WCDP = <player>
COMMAND POSSIBLE RESPONSES
AT+WCDP=? +WCDP : (0-1)
OK
AT+WCDP=0 OK
Select the speaker.
AT+WCDP? +WCDP: 0
OK

15.34.3 Defined values:


<player>
0: Speaker
1: Buzzer

15.35 Wavecom CPHS Mail Box Number +WMBN

15.35.1 Description:
This specific command allows to set the different mailbox numbers in SIM. The +CPHS
command can be used to know which mailbox numbers can be updated.

154
15.35.2 Syntax:
Command syntax: AT+WMBN = <LineId>,<number>,<type>
Response syntax: (AT+CPHS=2,2)
+WMBN = <LineId>,<number>,<type>,<status>
COMMAND POSSIBLE RESPONSES
AT+WMBN=? OK
AT+WMBN? OK
AT+CPHS=2,2 +WMBN: 1,"0123456789",129,1
Get the current Mail Box Numbers in SIM +WMBN: 2,”9876543210”,129,1
+WMBN: 3,,,0
+WMBN: 4,,,0
OK
AT+WMBN=1,”+33122334455”,145 OK
Set mailbox number for line1. Mailbox number for Line1 is set.
AT+WMBN=2,”0166778899”,129 OK
Set mailbox number for line2. Mailbox number for Line2 is set.
AT+WMBN=3,”0102030405”,129 +CME ERROR: 21
Set mailbox number for FAX Line. Invalid index: Fax Line mailbox number can not be updated
with this SIM card.
AT+CPHS=2,2 +WMBN: 1,"+ 33122334455",145,1
Get the current Mail Box Numbers again +WMBN: 2,”0166778899”,129,1
+WMBN: 3,,,0
+WMBN: 4,,,0
OK

15.35.3 Defined values:


<LineId>
1: Line 1
2: Line 2
3: FAX
4: DATA

<number>
Phone number in ASCII format.

<type>
TON/NPI (Type of address octet in integer format).

<status>When checked with “AT+CPHS=2,2”, it indicates if the number can be updated or not:
0: Update is not possible
1: Update is possible

155
15.36 Wavecom Open AT control command +WOPEN

15.36.1 Description:
This specific command allows to start, stop and get information about the current Open AT
embedded application.
NOTE:This command is only available if the Open AT feature is enabled (cf +WCFM command).

15.36.2 Syntax:
Command syntax: AT+WOPEN=<Mode>
Response syntax: +WOPEN: <Mode>[,<IntVersion>[<ExtVersion>]]
COMMAND POSSIBLE RESPONSES
AT+WOPEN=? +WOPEN: (0-2)
OK
AT+WOPEN? +WOPEN: 0
OK
AT+WOPEN=2 +WOPEN: 2, “AT v1.00”, “AT v1.00”
Get the Open-AT library versions. OK
Open-AT v1.00 library version. An embedded application has
been downloaded on this product.
AT+WOPEN=3 OK
The objects flash are erased
AT+WOPEN=1 OK
Start the embedded application. +WIND: 3
Product reset in order to start the embedded application.
AT+WOPEN = 3 +CME ERROR: 532
the embedded application is activated so the objects
flash are not erased.
AT+WOPEN=0 OK
Stop the embedded application. +WIND: 3
Product reset in order to stop the embedded application.
AT+WOPEN=3 OK
The objects flash are erased
AT+WOPEN? +CME ERROR: 3
The Open AT feature is disabled.

156
15.36.3 Defined values:
<Mode>
0: Stop the embedded application. If this one was running, the product resets.
1: Start the embedded application. If this one was stopped, the product resets.
2: Get the Open AT library versions.
3: Erase the objects flash of Open-AT embedded application.

NOTE: (Mode = 3) is only available if Open-AT embedded application is stopped (AT+WOPEN=0).

<IntVersion>
Ascii string giving the internal Open AT library version.

<ExtVersion>
Ascii string giving the external Open AT library version.

NOTE: If no embedded application is loaded, the <ExtVersion> parameter does not appear.

157
15.37 Wavecom Reset +WRST

15.37.1 Description:
This specific command allows to reset the module after the time specified by the second
parameter.

15.37.2 Syntax:
Command Syntax: AT+WRST =<Mode>,<Delay>
Response Syntax: +WRST: <Mode>,<Delay>,<RemainTime>
COMMAND POSSIBLE RESPONSES
AT+WRST=? OK
AT+WRST=0 OK
Disable timer
AT+WRST=1,”001:03” OK
Enable timer and put delay at 1 hour 3 minutes
AT+WRST? +WRST: 1,”001:03”,”001:01”
OK
Note: Timer activated to reset after 1 hour and 3 minutes.
Actually 1 hour and 1 minute remaining before next reset.

15.37.3 Defined values:


<val1>
0: timer reset is disabled
1: timer reset is enabled

<Delay>
“000:00”- “168:59”: specifie the time for reset

<RemainTime>
“000:00”- “168:59”: time before next reset

158
15.38 Set Standard Tone +WSST

15.38.1 Description:
This specific command allows to set/get the sound level of the Standard Tones.

15.38.2 Syntax:
Command Syntax: AT+WSST=[<sound level>][,<ring tone level>]
COMMAND POSSIBLE RESPONSES
AT+WSST=0 OK
Note: Set volume to Max.
AT+WSST=15 OK
Note: Set volume to Min.
AT+WSST=,5 OK
Note: Set ring tone level to 5
AT+WSST? +WSST: 15,5
OK
Note: get current standard tones sound level Note: current standard tones level is 15 (min.), and ring tone
level is 5.
AT+WSST=? +WSST: (0-15),(0-15)
Note: supported parameters OK

15.38.3 Defined values:


<sound level>
0: Max volume (default)
....
15: Min volume

<ring tone level>


0: Max volume (default)
....
15: Min volume

159
15.39 Wavecom Location +WLOC

15.39.1 Description:
This specific command can be used by the application to retrieve the local information:
MCC-MNC,LAC,CI,Network measurement,BCCH channel list, Timing Advance, Date and
Time.
Two ways may exist for the external application to know these information : on request of
the application, or automatically by the module every x seconds
(x has to be a multiple of 5 different from 0).
The location feature has to be activated to get information.
if the feature is not activated,”ERROR” is sent.
If the data are not valid at the requested time, the network measurement, BCCH list and
Timing Advance cannot be displayed (“,,” is displayed).

160
15.39.2 Syntax:
Command Syntax: AT+WLOC =< mode > [,< time period/dump >]
COMMAND POSSIBLE RESPONSES
AT+WLOC=0 OK
Note: stops the display of local information
AT+WLOC=3,255 OK
Note: set the wished information to display
(255 -> complete information)
AT+WLOC=1 +WLOC: 02f802,0006,7772,f13101b04cf51278
91138e95a846d160,8b49d08d0797c419e272e
10889a000009302170399020403c1020a03c5020a
03,00,010121111349ff
Note: displays once the local information OK
AT+WLOC=2,6 +CME ERROR:3
Note: 6 is not a multiple of 5
AT+WLOC=2,10 OK
+WLOC: 02f802,0006,7772,ed3001af4cf492780
b040889c74acc23,8b49d08d0797c419e272e1
0889a000009302160399020503c1020a03c5020
a03,00,010121111354ff
+WLOC: 02f802,0006,7772,ed3001af4cf492780
b040889c74acc23,8b49d08d0797c419e272e1
0889a000009302160399020503c1020a03c5020
a03,00,010121111354ff
+WLOC: 02f802,0006,7772,f02d01ae4cf41278
Note: displays OK then the current local 4b03c889c846dba5,8b49d08d0797c419e272e
information immediately for the first time and 10889a000009302170399020403c1020a03c
then every 10 seconds. 5020903,00,010121111404ff
AT+WLOC=? +CME ERROR:3
The feature “loca” is not activated
AT+WLOC? +CME ERROR:3
The feature “loca” is not activated
AT+WLOC=? OK
The feature “loca” is activated
AT+WLOC?
The location is not in mode automatic +WLOC: 0,5,255
The period value is set to 5 seconds
The configuration value is set to 255 OK
AT+WLOC? +WLOC: 1,10,20
The location is in mode automatic
The period value is set to 10 seconds OK
The configuration value is set to 20

161
15.39.3 Defined values :
<mode>
0: Stop automatic shots
1: One shot requested
2: Automatic shots requested (every x seconds)
3: Configuration of the wished information

for mode == 2
<time period>
optional parameter – range: 5-255 – in seconds
it has to be a multiple of 5.
default value of time period: 5 seconds

NOTE: if no time period is given with the command “at+wloc=2”, 5 seconds will be choosen.
The automatic mode for location is saved in EEPROM, so will be taken into account after an Init
(+WLOC:… will be displayed).

for mode == 3
<dump>
optional parameter – range: 1-255 (at least 1 bit set to 1).
if bit 0 set to 1: DaT will be given in the response
if bit 1 set to 1: TA will be given in the response
if bit 2 set to 1: BCCH will be given in the response
if bit 3 set to 1: NetMeas will be given in the response
if bit 4 set to 1: CI will be given in the response
if bit 5 set to 1: LAC will be given in the response
if bit 6 set to 1: MNC-MCC will be given in the response
After having downloaded the EEPROM configuration: default value of dump =0xFF (all
information given).

The <dump> value set with the command “at+wloc=3,xx” is saved in EEPROM, so will be
taken into account after an Init.

15.39.4 Fields od the response of at+wloc=1 or at+wloc=2:


The format of these fields are as specified in 04.08
MCC-MNC: 3 bytes
LAC: 2 bytes
CI: 2 bytes
Network measurement: 16 bytes (chapter 10.5.2.20)
BCCH channel list: maximum 48 bytes(version V0)
or 129 bytes (version V1)
Timing Advance: 1 byte
Date and Time: 7 bytes: Date, time and timezone at STLK Format

162
15.39.5 Fields od the response of at+wloc?:
+wloc: mode, time period, dump
mode :
0: no automatic mode
1: automatic mode
period, dump: see 15.39.3

15.40 Wavecom Bus Read +WBR

15.40.1 Description
This specific command allows to read a buffer from a specific bus (SPI or I2C Soft).
NOTE: Bus configuration is set by the +WBM command.

15.40.2 Syntax
Command Syntax: AT+WBR=<BusId>,<Size>[,<Address>[,<Opcode>]]
Response syntax: +WBR:
<Data>
OK
COMMAND POSSIBLE RESPONSES
AT+WBR=0,9,1,”08C9” +WBR: 0A5F98231012345678
Read 9 bytes from the SPI bus, OK
using SPI_EN chip select, after have
sending the 0xC9 Opcode byte.
AT+WBR=1,5,”2A” +WBR: 0102030405
Read 5 bytes from the I2C Soft bus, OK
at the 0x2A slave address.

15.40.3 Defined values


<BusId>
0: SPI bus.
1: I2C Soft bus.

<Size>
Size of data to read (max 256 bytes).

163
<Address>
For SPI bus:
Chip select to use to read data from the SPI bus.
0: No Chip Select. The application should use a GPIO as a Chip Select.
1: SPI_EN Chip Select.
2: SPI_AUX Chip Select.

For I2C Soft bus:


Slave address byte, in hexadecimal characters (default “00”).
This is a 7-bits address, shifted to left from 1 bit, padded with the LSB set to 1 (to read),
and sent first on the I2C bus before performing the reading operation.

NOTE: this parameter is required for SPI bus, and optional for I2C Soft bus.

<Opcode>
(for SPI bus only, default “0000”)
2 bytes hexadecimal string, used to send an operation code byte on the SPI bus, before
performing the reading operation. The first byte is the operation code length, in bits (from
1 to 8). The second byte is the operation code value.

NOTE: as the MSB in always sent first, if the length is less than 8 bits, only the most significant bytes
will be sent (example : to send first a bit set to 1, the opcode parameter must be set to “0180”).

15.41 Wavecom Bus Write +WBW

15.41.1 Description
This specific command allows to write a buffer on a specific bus (SPI or I2C).
NOTE: Bus configuration is set by the +WBM command.

15.41.2 Syntax
Command Syntax: AT+WBW=<BusId>,<Size>[,<Address>]<CR>
> <Data Buffer> <ctrl-Z >
COMMAND POSSIBLE RESPONSES
AT+WBW=0,10,1<CR> OK
0123456789ABCDEF0123<ctrl-Z> Data buffer is written on SPI bus.
Write 10 bytes on the SPI bus, using the SPI_EN chip select.
AT+WBW=1,5<CR> OK
0246801234<ctrl-Z> Data buffer is written on I2C Soft bus.
Write 5 bytes on the I2C Soft bus.

164
15.41.3 Defined values
<BusId>
0: SPI bus.
1: I2C Soft bus.

<Size>
Size of data buffer, in bytes. (max. 256 bytes)

<Address>
For SPI bus:
Chip select to use to write data on the SPI bus.
0: No Chip Select. The application should use a GPIO as a Chip Select.
1: SPI_EN Chip Select.
2: SPI_AUX Chip Select.

For I2C Soft bus:


Slave address byte, in hexadecimal characters (default “00”).
This is a 7-bits address, shifted to left from 1 bit, padded with the LSB set to 0 (to write),
and sent first on the I2C bus before performing the writing operation.

NOTE: this parameter is required for SPI bus, and optional for I2C Soft bus.

<Data Buffer>
Data buffer to write on the specific bus. This parameter must only contain hexadecimal
characters (0-9, A-F), and must be long as twice the <Size> parameter.

165
15.42 Wavecom Bus Management +WBM

15.42.1 Description
This specific command allows to manage specific buses (SPI or I2C Soft) with a given
configuration.

15.42.2 Syntax
Command Syntax: AT+WBM=<BusId>,<Mode>
[,<Clk Speed / SCL Gpio>[],<Clk Mode / SDA Gpio>]]
COMMAND POSSIBLE RESPONSES
AT+WBM=0,1,1,3 OK
Open SPI bus with configuration:
Clock Speed: 812 kHz
Clock Mode: 3
AT+WBM=1,1,0,4 OK
Open I2C Soft bus with configuration:
Scl Gpio: 0
Sda Gpio: 4
AT+WBM=0,2 +WBM: 0,1,1,3
OK
AT+WBM=1,0 OK
Close I2C bus.
AT+WBM=1,2 +WBM: 0,0,0,4
OK
AT+WBM=1,1 OK
Open I2C Soft bus with the last configuration :
Scl Gpio: 0
Sda Gpio: 4
AT+WBM = 1,2 +WBM: 1,1,0,4
OK

15.42.3 Defined values


<BusId>
0: SPI bus.
1: I2C bus.

<Mode>
0: close bus.
1: open bus.
2: get bus status.

166
<Clk Speed / SCL Gpio>
For SPI bus:
Clock Speed (default 0)
0: 101Khz.
1: 812Khz.
2: 1625Mhz.
3: 325Mhz.

For I2C bus:


Scl Gpio (default 0)
The Scl Gpio value is between 0 and 7.
It must be a Gpio (not Gpi or Gpo) and not allocated by an Open-AT embedded
application.

<Clk Mode / SDA Gpio>


For SPI bus:
Clock Mode (default 0)
0: the rest state is 0, the data is valid on rising edge.
1: the rest state is 0, the data is valid on falling edge.
2: the rest state is 1, the data is valid on rising edge.
3: the rest state is 1, the data is valid on falling edge.

For I2C Soft bus:


Sda Gpio (default 4)
The Sda Gpio value is between 0 and 7.
It must be a Gpio (not Gpi or Gpo) and not allocated by an Open-AT embedded
application.

NOTES:
❑ If the I2C soft bus is opened, the two used GPIO are not available for the +WIOR , +WIOW,
+WIOM commands. When the I2C bus is closed, these commands resume the control of the
two GPIO.
❑ A bus may not be available to open operation if an Open-AT embedded application has
opened it before. In this case, the +WBM command will return +CME ERROR: 3.

167
15.43 Wavecom Hang-up +WATH

15.43.1 Description
This specific command is used by the application to disconnect the remote user, specifying
a release cause and the location. In the case of multiple calls, all calls are released (active,
on-hold and waiting calls).

15.43.2 Syntax
Command Syntax: AT+WATH=<RelCause>,<location>
COMMAND POSSIBLE RESPONSES
AT+WATH=31 OK
Note: Ask for disconnection with release Note : Every call, if any, are released
cause=normal and location=USER
AT+WATH=? +WATH: (1-127),(0-5,7,10)
AT+WATH=17,2 OK
Note: Ask for disconnection with release cause=user Note: Every call, if any, are released
busy and location= public network serving the local user

15.43.3 Defined values


<RelCause>
decimal value from 1 to 127
see the table in appendices 18.4 “Failure Cause from GSM 04.08 recommendation”

<location>
optional parameter (default value =0)
values as defined in 04.08
0: user
1: private network serving the local user
2: public network serving the local user
3: transit network
4: public network serving the remote user
5: private network serving the remote user
7: international network
10: network beyond interworking point

NOTES: “AT+WATH=0” is the same as “ath”

168
16 SIM TOOLKIT

16.1 Overview of SIM Application ToolKit

16.1.1 Summary
SIM ToolKit, also known as “SIM Application ToolKit” introduces new functionalities,
which open the way to a broad range of value added services.
The principle is to allow service providers to develop new applications (e.g.. for banking,
travel, ticket booking, etc.) for subscribers and to download them into the SIM.
This solution allows new services to be accessible to the user by adding new SIM-based
applications without modifying the handset.

16.1.2 Functionality
SIM Toolkit refers to the functionalities described in the GSM Technical specification 11.14.
It introduces about twenty five new commands for the SIM. Three classes of ToolKit
functionalities have been defined, with class 1 offering a subset of commands and class 3
offering the full range of commands (See table 1 in APPENDIX B).
The SIM Application Toolkit supports:

❑ profile download,
❑ proactive SIM,
❑ data download into SIM.
❑ menu selection,
❑ call control by SIM.

16.1.3 Profile download


The Profile Download instruction is sent by the customer application to the SIM as part of
the initialization. It is used to indicate which SIM Application Toolkit features the customer
application supports.
The AT command used for this operation is +STSF (SIM ToolKit Set Facilities).

169
16.1.4 Proactive SIM
A proactive SIM provides a mechanism whereby the SIM can ask the customer application
to perform certain actions.
These actions include:
❑ display menu,
❑ display given text,
❑ get user input,
❑ send a short message,
❑ play the requested tone,
❑ set up a call,
❑ provide location information.
This mechanism allows SIM applications to generate powerful menu-driven sequences on
the customer application and to use services available in the network.
The commands used for this operation are:
+STIN (SIM Toolkit Indication),
+STGI (SIM Toolkit Get Information),
+STGR (SIM Toolkit Give Response).

16.1.5 Data Download to SIM


Data downloading to the SIM allows (SMS, phonebook…) data or programs (Java applets)
received by SMS or by Cell Broadcast to be transferred directly to the SIM Application.
This feature does not need any AT command. It is transparent to the customer application.

16.1.6 Menu Selection


A set of menu items is supplied by the SIM Application ToolKit. The menu selection
command can then be used to inform the SIM Application which menu item is selected.
The commands used for this operation are +STIN, +STGI and +STGR.

16.1.7 Call control by SIM


The call control mechanism allows the SIM to check all dialed numbers, supplementary
service control strings and USSD strings before connecting to the network. This gives the
SIM the ability to allow, bar or modify the string before the operation starts.
The commands used for this operation are :
+STCR (SIM Toolkit Control Response),
+STGR (SIM Toolkit Give Response).

170
16.2 Messages exchanged during a SIM ToolKit operation.
The following scheme shows the SIM Toolkit commands and unsolicited results that are
exchanged.

+STSF=X,XXXXXXXX
STEP 1: Configuration and Activation

+STIN=X
STEP 2: SIM sends pro-active command

WAVECOM +STGI=X Customer


Product Application
+STGI response
STEP 3: Customer application gets all the information.

+STCR:X
+STGR=X,XXXXXX
STEP 4: User response is sent to the SIM

Figure 5: The Development Toolkit Environment

On the first step the customer application informs the WAVECOM product which facilities
are supported. This operation is performed with the +STSF (SIM ToolKit Set Facilities)
command, which also allows to activate or deactivate the SIM Toolkit functionality.
On the second step an unsolicited result +STIN (SIM ToolKit indication) is sent by the
product, in order to indicate the customer application which command type the SIM
Application Toolkit is running on the SIM card. The last SIM Toolkit indication can be
requested by the +STIN? command.
On the third step the customer application uses the +STGI (SIM ToolKit Get Information)
command to get all the information about the SIM ToolKit command, given by +STIN.
On the fourth step the customer application uses the +STGR (SIM Toolkit Give Response)
to send its response (if any) to the SIM ToolKit Application.
The +STCR (SIM Toolkit Control response) indication is an unsolicited result sent by the
SIM when Call control functionality is activated and before the customer application has
performed any outgoing call, SMS, SS, or USSD.

171
16.3 SIM TOOLKIT COMMANDS

16.3.1 SIM ToolKit Set Facilities (+STSF)

16.3.1.1 Description:
This command allows SIM ToolKit facilities to be activated, deactivated or configured.
16.3.1.2 Syntax:
Command syntax: +STSF=<mode>[,<config>][,<Timeout>][,<AutoResponse>]
COMMAND POSSIBLE RESPONSES
+STSF=<Mode>[,<Config>] OK
[,<Timeout>][,<AutoResponse>] +CME ERROR: <err>
+STSF? +STSF: <Mode>,<Config>,<Timeout>,<Autoresponse>
+STSF=? +STSF: (0-2), (160060C01F - 5FFFFFFF7F),(1-255),(0-1)
OK
16.3.1.3 Defined values:
<mode>
0: Deactivates the SIM Toolkit functionalities.
1: Activates the SIM Toolkit functionalities.
2: Configures the SIM Toolkit functionalities.

<Config>
(160060C01F – 5FFFFFFF7F) (hex format)

<Timeout>
1-255: Timeout for user responses (multiple of 10 seconds).

<Autoresponse>
0: Automatic response is not activated
1: Automatic response is activated

The activation or deactivation of the SIM Toolkit functionalities requires the use of the
+CFUN (Set phone functionality) command to reset the product (this operation is not
necessary if PIN is not entered yet).

The <Config> parameter gives the coding of the TERMINAL PROFILE, precisely the list of
SIM Application Toolkit facilities that are supported by the customer application.

The <Timeout> parameter (multiple of 10 seconds) sets the maximum time the user has
for reacting (to select an item, to input a text, etc).

When the <Autoresponse> is activated, the +STIN indication for Play Tone (5), Refresh (7),
Send SS (8), Send SMS (9) or Send USSD (10) is automatically followed by the
corresponding +STGI response.

172
NOTE: Some bits are related to the product only and not to the customer application. The product
automatically sets these bits to either 0 or 1 whatever the user enters with the +STSF command. Those
values are given in Appendix C.
Each facility is coded on 1 bit:

❑ bit = 1: facility is supported by the customer application.


❑ bit = 0: facility is not supported by the customer application.
Only the first five bytes of the TERMINAL PROFILE (Class 2) can be configured, the other
are set to 0. (See structure of TERMINAL PROFILE in APPENDIX C)

16.3.1.4 Error codes:


+CME ERROR: 3 Operation not allowed. This error is returned when a wrong parameter
is entered.
16.3.1.5 Example:

AT+CMEE=1 Enable the reporting of mobile equipment errors


OK
AT+WIND=15 Set Wavecom indications
OK
AT+CPAS Query ME Status
+CPAS: 0 ME is ready.
OK
AT+STSF=? Test command SIM ToolKit Set Facilities
+STSF: (0-2), (160060C01F – 5FFFFFFF7F),(1-255)
OK
AT+STSF?
+STSF: 0,”160060C000”,3 No activation of SIM ToolKit functionality
OK
AT+STSF=2,”5FFFFFFF7F” Set all SIM ToolKit facilities (class 3).
OK
AT+STSF=3 Syntax Error
+CME ERROR: 3
AT+STSF=1 Activation of SIM ToolKit functionality
OK
AT+CFUN=1 Reboot Software.
OK
AT+CPIN? Is the ME requiring a password?
+CPIN: SIM PIN Yes, SIM PIN required
AT+CPIN=0000
OK PIN Ok
+WIND: 4 Init phase is complete
AT+STSF?
+STSF: 1,”5FFFFFFF7F”,3 SIM ToolKit functionality activated with all facilities
OK

16.3.2 SIM ToolKit Indication (+STIN)

173
16.3.2.1 Unsolicited result:
In order to allow the customer application to identify the pro-active command sent via SIM
ToolKit, a mechanism of unsolicited SIM ToolKit indications (+STIN) is implemented.

Syntax: +STIN: <CmdType>


Option : <CmdType>
0: Indicates that a ‘Setup Menu’ pro-active command has been sent from the SIM.
1: Indicates that a ‘Display Text’ pro-active command has been sent from the SIM.
2: Indicates that a ‘Get Inkey’ pro-active command has been sent from the SIM.
3: Indicates that a ‘Get Input’ pro-active command has been sent from the SIM.
4: Indicates that a ‘Setup Call’ pro-active command has been sent from the SIM.
5: Indicates that a ‘Play Tone’ pro-active command has been sent from the SIM. (*)
6: Indicates that a ‘Sel Item’ pro-active command has been sent from the SIM.
7: Indicates that a ‘Refresh’ pro-active command has been sent from the SIM. (*)
8: Indicates that a ‘Send SS’ pro-active command has been sent from the SIM. (*)
9: Indicates that a ‘Send SMS’ pro-active command has been sent from the SIM. (*)
10: Indicates that a ‘Send USSD’ pro-active command has been sent from the SIM. (*)
11: Indicates that a ‘SETUP EVENT LIST’ pro-active command has been sent from the SIM.
98: Indicates the timeout when no response from user.
99: Indicates that a “End Session” has been sent from the SIM.

(*) if the automatic response parameter is activated, this indication is followed by the
corresponding +STGI response.
16.3.2.2 Last SIM toolkit indication:
The last SIM toolkit indication sent by the SIM can be requested by the AT+STIN?
command. This command is only usable between the sending of the STIN indication by
the SIM (step 2 : see section 16.2) and the response of the user with the +STGI command
(step 3).
Command Syntax: +STIN?
COMMAND POSSIBLE RESPONSES
+STIN? +STIN: 0
OK
Note: Ask for the last SIM toolkit indication Note: the last SIM toolkit indication was a Setup Menu
sent by the SIM
+STGI=0 Note: Display the SIM toolkit application menu
+STIN? +CME ERROR: 4
Note: Ask for the last SIM toolkit indication Note: operation not supported, the +STGI
sent by the SIM command has been already used

174
16.3.3 SIM ToolKit Get Information (+STGI)

16.3.3.1 Description:
This command allows to get the information (text to display, Menu information,
priorities…) of a pro-active command sent from the SIM.
The information is returned only after receiving a SIM Toolkit indication (+STIN).
16.3.3.2 Syntax:
Command Syntax: +STGI=<CmdType>
COMMAND POSSIBLE RESPONSES
+STGI=<CmdType> See Table 1
+CME ERROR: <err>
+STGI=? +STGI: (0-11)
OK

175
Table 1
Cmd Type Description Possible responses
0 Get information about ‘Setup +STGI: <Alpha Identifier menu>
Menu’ pro-active command. +STGI: <Id1>,<NbItems>,<Alpha Id1 Label>,
<Help Info>[,<NextActionId>]<CR><LF>
+STGI: <Id2>,<NbItems>,<Alpha Id2 Label>,
<Help Info>[,<NextActionId>]<CR><LF>
[…]]
No action expected from SIM.
1 Get information about ‘Display +STGI: <Prior>,<Text>,<ClearMode>
text’ pro-active command. No action expected from SIM.
2 Get information about ‘Get Inkey’ +STGI: <Format>,<HelpInfo>[,<TextInfo>]
pro-active command. SIM expects key pressed (+STGR).
3 Get information about ‘Get Input’ +STGI: <Format>,<EchoMode>,<SizeMin>,
pro-active command. <SizeMax>,<HelpInfo>[,<TextInfo>]
SIM expects key input (+STGR).
4 Get information about ‘Setupt call’+STGI: <Type>,<CalledNb>,<SubAddress>,<Class>
pro-active command. SIM expects user authorization (+STGR).
5 Get information about ‘Play Tone’ +STGI: <ToneType>[,<TimeUnit>,
pro-active command. <TimeInterval>,<TextInfo>]
No action.
6 Get information about ‘Sel Item’ +STGI: <DefaultItem>,
pro-active command. <Alpha Identifier menu><CR><LF>
+STGI: <Id1>,<NbItems>,<Alpha Id1 Label>,
<Help Info>[,<NextActionId>]<CR><LF>
+STGI: <Id2>,<NbItems>,<Alpha Id2 Label>,
<Help Info>[,<NextActionId>]<CR><LF>
[…]]
SIM expects an item choice (+STGR).
7 Get information about ‘Refresh’ +STGI: <RefreshType>
pro-active command. No action (Refresh done automatically by product).
8 Get information about ‘Send SS’ +STGI:<TextInfo>
pro-active command. No action (Send SS done automatically by product).
9 Get information about ‘Send SMS’+STGI: <TextInfo>
pro-active command. No action (Send SMS done automatically by product).
10 Get information about ‘Send USSD’ +STGI: <TextInfo>
pro-active command. No action (Send USD done automatically by product).
11 Get information about ‘SETUP +STGI: <Evt>
EVENT LIST’ pro-active command.

176
16.3.3.3 Defined values:
Values when CmdType=0 (Setup menu)
<Alpha Idenitifer menu> Alpha identifier of the main menu.
<Idx> (1-255) Menu item Identifier.
<NbItems> (1-255) Number of items in the main menu.
<Alpha Idx Label> Alpha identifier label of items in ASCII format.

<HelpInfo>
0: No help information available.
1: Help information available.

<NextActionId> Contains a pro-active command identifier. (see the table in APPENDIX D)


Compared to other commands the customer application can always get information about
setup menu after having received the +STIN:0 indication.

Values when CmdType=1 (Display text)


<Prior>
0: Normal priority of display.
1: High priority of display.

<Text> Text to display in ASCII format.

<ClearMode>
0: Clear message after a delay (3 seconds)
1: Wait for user to clear message.

Values when CmdType=2 (Get Inkey)


<Format>
0: Digit (0-9, *, #,and +)
1: SMS alphabet default.
2: UCS2

<HelpInfo>
0: No help information available.
1: Help information available.

<TextInfo> Text information in ASCII format.

Values when CmdType=3 (Get Input)


<Format>
0: Digit (0-9, *, #,and +)
1: SMS alphabet default.
2: UCS2
3: Unpacked forma
4: Packed format.

177
<EchoMode>
0: Echo off.
1: Echo on.
<SizeMin> (1-255) Minimum length of input.
<SizeMax> (1-255) Maximum length of input.

<HelpInfo>
1: No help information available.
0: Help information available.

<TextInfo> Text information in ASCII format.

Values when CmdType=4 (Setup Call)


<Type>
0: Set up call but only if not currently busy on another call.
1: Set up call, putting all other calls (if any) on hold.
2: Set up call, disconnecting all other calls (if any).

<CalledNb> Called party number in ASCII format.

<SubAdress> Called party sub-address in ASCII format.

<Class>
0: Voice call.
1: Data call.
2: Fax call

Values when CmdType=5 (Play tone)


<ToneType>
0: Tone Dial.
1: Tone Busy.
2: Tone Congestion.
3: Tone Radio ack
4: Tone Dropped.
5: Tone Error.
6: Tone Call waiting.
7: Tone Ringing.
8: Tone General beep.
9: Tone Positive beep.
10: Tone Negative beep.

<TimeUnit>
0:Time unit used is minutes.
1:Time unit used is seconds.
2:Time unit used is tenths of seconds.

178
<TimeInterval> (1-255) Time required expressed in units.
<TextInfo> Text information in ASCII format.

Values when CmdType=6 (Sel Item)


<DefaultItem> (1-255) Default Item Identifier.
<Alpha Idenitifer menu> Alpha identifier of the main menu.
<Idx> (1-255) Identifier items.
<NbItems> (1-255) Number of items in the menu.
<Alpha Idx Label> Alpha identifier label of items in ASCII format.
<HelpInfo>
0: No help information available.
1: Help information available.

<NextActionId> Contains a pro-active command identifier. (see the table in APPENDIX D)

Values when CmdType=7 (Refresh)


<RefreshType>
0: SlM initialization and full file change notification.
1: File change notification.
2: SIM initialization and file change notification.
3: SIM initialization.
4: SIM reset.

Values when CmdType=8 (Send SS)


<TextInfo> Text information in ASCII format.

Values when CmdType=9 (Send SMS)


<TextInfo> Text information in ASCII format.

Values when CmdType=10 (Send USSD)


<TextInfo> Text information in ASCII format.

Values when CmdType=11 (Setup Event List)


<Evt>
1: Reporting asked for an ‘Idle Screen’ event.
2: Reporting asked for an ‘User Activity’ event.
3: Reporting asked for ‘Idle Screen’ and ‘User Activity’ events.
4: Cancellation of reporting event.

REM.: For the UCS2 format texts are displayed in Hexa Ascii format. Example : When the
SIM sends a TextString containing 0x00 0x41 the text displayed is “0041”.

179
16.3.3.4 Error codes:
+ CME ERROR: 3 Operation not allowed. This error is returned when a wrong parameter
is detected.

+CME ERROR: 4 Operation not supported. This error is returned when the user wants to
get information about a SIM ToolKit pro-active command (with SIM
ToolKit functionality not activated.)

+CME ERROR: 518 SIM ToolKit indication not received. This error is returned when the
SIM Toolkit indication (+STIN) has not been received.
16.3.3.5 Example:
Initially, all facilities are activated, the PIN is not required and SIM toolkit functionality is
activated.

AT+CMEE=1 Enable the reporting of mobile equipment errors


OK
AT+WIND=15 Set Wavecom indications
OK
AT+STSF?
+STSF: 1,”5FFFFFFF7F”,3 SIM ToolKit functionality activated with all facilities.
OK
+STIN: 0 The main menu has been sent from the SIM.
AT+STIN?
+STIN: 0
OK
AT+STGI=0 Get information about the main menu
+STGI: ”SIM TOOLKIT MAIN MENU” Main menu contains 3 items.
+STGI: 1,3,”BANK”,0
+STGI: 2,3,”QUIZ”,0
+STGI: 3,3,”WEATHER”,0
OK
AT+STIN?
+CME ERROR: 4

180
16.3.4 Unsolicited Result : SIM ToolKit Control Response (+STCR)
When the customer application makes an outgoing call or an outgoing SMS and if the call
control facility is activated, CALL CONTROL and SMS CONTROL responses can be
identified. This is also applicable to SS calls.
Syntax: +STCR: <Result>[,<Number>,<MODestAddr>,<TextInfo>]
Option :
<Result>
0: Control response not allowed.
1: Control response with modification.

<Number> Called number, Service Center Address or SS String in ASCII format.

<MODestAddr> MO destination address in ASCII format.

<TextInfo> Text information in ASCII format.

16.3.5 SIM ToolKit Give Response (+STGR)

16.3.5.1 Description:
This command allows the application/user to select an item in the main menu, or to
answer the following proactive commands :

❑ GET INKEY Key pressed by the user.


❑ GET INPUT Message entered by the user.
❑ SELECT ITEM Selected item.
❑ SETUP CALL User confirmation.
❑ DISPLAY TEXT User confirmation to clear the message.
❑ SETUP EVENT LIST Reporting events.

It is also possible to terminate the current proactive command session by sending a


Terminal Response to the SIM, with the following parameters :

❑ BACKWARD MOVE Process a backward move


❑ BEYOND CAPABILITIES Command beyond ME capabilities
❑ UNABLE TO PROCESS ME is currently unable to process command
❑ NO RESPONSE No response from the user
❑ END SESSION User abort.

181
16.3.5.2 Syntax:
Command Syntax: +STGR=<CmdType>[,<Result>,<Data>]
COMMAND POSSIBLE RESPONSES
+STGR=<CmdType>[,<Result>,<Data>] OK
+CME ERROR: <err>
For GetInput with <Result>=1:
+STGR=3,1<CR> OK
<Data><Ctrl Z> +CME ERROR: <err>
For GetInkey with <Result>=1 OK
+STGR=2,1,”<Data>” +CME ERROR: <err>
+STGR=? OK
16.3.5.3 Defined values:
<CmdType>
0: Item selection in the main menu.
1: User confirmation to clear a ‘Disp Text’.
2: Response for a ‘Get Inkey’.
3: Response for a ‘Get Input’.
4: Response for a ‘Setup call’.
6: Response for a ‘Sel Item’.
11: Reponse for a ‘Setup event list’.
95: Backward move
96: Command beyond ME capabilities
97: ME currently unable to process command
98: No response from the user.
99: User abort.

Values when CmdType=0 (Select an item from the main menu)


<Result>
1: Item selected by the user.
2: Help information required by user.
<Data> Contains the item identifier of the item selected by the user.

Values when CmdType=1 (Confirm the display text clearing)


No values.

Values when CmdType=2 (Get Inkey)


<Result>
0: Session ended by user.
1: Response given by the user.
2: Help information required by user.
<Data> Contains the key pressed by the user.

182
Values when CmdType=3 (Get Input)
<Result>
0: Session ended by user.
1: Response given by the user.
2: Help information required by user.
<Data> Contains the string of characters entered by the user.

NOTE: For Inputs in UCS2 format, the data are entered in ASCII format. Example : For
“8000410042FFFF” entered, the SIM receives 0x00 0x41 0x00 0x42 with UCS2 DCS. (See the Appendix
E about the different UCS2 syntaxes).

Values when CmdType=4 (Setup call)


<Result>
0: User refuses the call.
1: User accepts call.

Values when CmdType=6 (Select Item)


<Result>
0: Session terminated by the user
1: Item selected by the user
2: Help information required by the user
3: Return to the back item
<Data> Contains the item identifier selected by the user

Values when CmdType=11 (Setup Event List)


<Result>
1: Idle screen available.
2: User activity event.

Sending a Terminal Response to the SIM:


Values when CmdType=95 (Backward Move)
Values when CmdType=96 (Command beyond ME capabilities)
Values when CmdType=97 (ME currently unable to process command)
Values when CmdType=98 (No response from the user)
Values when CmdType=99 (SIM Toolkit Session aborting by the user)
No values.
It is possible to send a Terminal Response after the +STIN indication (step 2, cf §16.2), or
after the +STGI command (step 3).

NOTE: For the SETUP MENU Proactive Command, it is only possible to send a Terminal Response
after the +STIN: 0 indication, not after a +STGI=0 request.
All of the Terminal Responses are not possible with all of the Proactive Commands. Compatibility
between available Terminal Responses and Proactive Commands is given in Appendix B, Table 2. If a
Terminal Response is attempted during a incompatible Proactive Command session,
a +CME ERROR: 3 will be returned.

183
16.3.5.4 Possible error codes:
+ CME ERROR: 3 Operation not allowed. This error is returned when a wrong parameter
is detected.
+CME ERROR: 4 Operation not supported. This error is returned when the user gives a
response with SIM ToolKit functionality not activated. Or if the SIM
Toolkit indication (+STIN) has not been received.
16.3.5.5 Example:
Initially, all facilities are activated, the PIN is not required and the SIM toolkit functionality
is activated.

+STIN: 0 The main menu has been sent from the SIM.
AT+STGI=0 Get information about the main menu
+STGI: 1,3,”BANK”,0 The main menu contains 3 items.
+STGI: 2,3,”QUIZ”,0
+STGI: 3,3,”WEATHER”,0
OK
AT+STGR=0,1,1 The item 2 of the main menu has been selected.
OK
+STIN: 6 The Sel item menu has been sent from the SIM.
AT+STGI=6 Get information about the BANK menu
+STGI: 1,”BANK” The BANK menu contains two items.
+STGI: 1,2,”PERSONAL ACCOUNT ENQUIRY”,1
+STGI: 2,2,”NEWS”,0
OK
AT+STGR=6,1,1 Select Item 1.
OK
+STIN: 3 User request to enter Password sent.
AT+STGI=3 Get information about this request.
+STGI: 0,0,4,4,0,”Enter Account Password:’
OK
AT+STGR=3,1<CR> The user enters the Password.
>0000<Ctrl Z>
OK
+STIN:1 A text info has been sent from the SIM.
AT+STGI=1 Get information about this text.
+STGI: 0,”Password correct, please wait for response”,0
OK
+STIN: 9 SIM requests a bank account update from bank server via the network (SEND SMS)
AT+STGI=9 Get all information about the SEND SMS
+STGI: ”Send account balance of user, authorization ok”
OK

184
********* After a short period of time. ********

+STIN: 5 Transaction is complete: BEEP


+STGI=5 Get information about the Tone
+STGI: 9,1,1
+STIN: 1 Display text indication
AT+STGI=1
+STGI: 0,”Your account balance is 1000 $”,0
OK

185
17 Other AT commands

17.1 V.25 ter recommendation


The commands not listed in this document are not supported. For these commands, the
product will then answer with "ERROR".
All modulation control, error control and data compression commands are not recognized.
An "ERROR" string will be returned.

17.2 GSM 07.05 recommendation


All the 07.05 commands not described in this manual are not implemented. The product
will then answer "ERROR" to these commands.

17.3 GSM 07.07 recommendation


All the 07.07 commands not described in this manual are not implemented. The product
will then answer "ERROR" to these commands.

186
18 Appendices

18.1 ME error result code : +CME ERROR: <error>


<error> Meaning Resulting from the following commands
3 Operation not allowed All GSM 07.07 commands (+CME ERROR: 3)
4 Operation not supported All GSM 07.07 commands (+CME ERROR: 4)
5 PH-SIM PIN required (SIM lock) All GSM 07.07 commands (+CME ERROR: 5)
10 SIM not inserted All GSM 07.07 commands (+CME ERROR: 10)
11 SIM PIN required All GSM 07.07 commands (+CME ERROR: 11)
12 SIM PUK required All GSM 07.07 commands (+CME ERROR: 12)
13 SIM failure All GSM 07.07 commands (+CME ERROR: 13)
16 Incorrect password +CACM, +CAMM, +CPUC, +CLCK, +CPWD,
+CPIN, +CPIN2 (+CME ERROR: 16)
17 SIM PIN2 required +CPBW (FDN), +CLCK (FDN),
18 SIM PUK2 required +CACM, +CAMM, +CPUC, +CPBW (FDN),
+CPIN, +CPIN2, +CLCK (FDN), +CPWD
20 Memory full +CPBW
21 Invalid index +CPBR, +CPBW, ATD>[mem]index, +WMGO
22 Not found +CPBF, +CPBP, +CPBN, +CGSN, +WOPN,
ATD>[mem]”name”
24 Text string too long +CPBW, +CPIN, +CPIN2, +CLCK, +CPWD
26 Dial string too long +CPBW, ATD, +CCFC
30 No network service +VTS, +COPS=?, +CLCK, +CCFC,
+CCWA, +CUSD
32 Network not allowed – +COPS
emergency calls only
40 Network personalization All GSM 07.07 commands (+CME ERROR: 40)
PIN required (Network lock)

18.2 Message service failure result code: +CMS ERROR : <er>


<er> is defined as below :
<er> Meaning Resulting from the following commands
1 to 127 Error cause values from the GSM +CMGS, +CMSS
recommendation 04.11 Annex E-2
301 SMS service of ME reserved +CSMS (with +CMS: ERROR 301)

187
302 Operation not allowed All SMS commands (+CMSS, +CMGL,
+CPMS, +CSMP…
303 Operation not supported All SMS commands
304 Invalid PDU mode parameter +CMGS, +CMGW
305 Invalid text mode parameter +CMGS, +CMGW, +CMSS
310 SIM not inserted All SMS commands
311 SIM PIN required All SMS commands
312 PH-SIM PIN required All SMS commands
313 SIM failure All SMS commands
316 SIM PUK required All SMS commands
317 SIM PIN2 required All SMS commands
318 SIM PUK2 required All SMS commands
321 Invalid memory index +CMGR, +CMSS, +CMGD
322 SIM memory full +CMGW
330 SC address unknown +CSCA?, +CMSS, +CMGS
340 no +CNMA acknowledgement +CNMA
expected

18.3 Specific error result codes


<error> Meaning Resulting from the following commands
500 unknown error. All commands
512 MM establishment failure (for SMS). +CMGS, +CMSS (+CMS ERROR: 512)
513 Lower layer failure (for SMS) +CMGS, +CMSS (+CMS ERROR: 513)
514 CP error (for SMS). +CMGS, +CMSS (+CMS ERROR: 514)
515 Please wait, init or command All commands ( “+CME ERROR: 515” or
processing in progress. “+CMS ERROR: 515”)
517 SIM Toolkit facility not supported. +STGI
518 SIM Toolkit indication not received.+STGI
519 Reset the product to activate or +ECHO, +VIP
change a new echo cancellation algo.
520 Automatic abort about get +COPS=?
plmn list for an incoming call.
526 PIN deactivation forbidden +CLCK
with this SIM card.
527 Please wait, RR or MM is busy. +COPS
Retry your selection later.

188
528 Location update failure. +COPS
Emergency calls only.
529 PLMN selection failure. +COPS
Emergency calls only.
531 SMS not sent : the <da> +CMGS, +CMSS (+CMS ERROR: 531)
is not in FDN phonebook, and
FDN lock is enabled. (for SMS)
532 the embedded application is +WOPEN
actived so the objects flash
are not erased

18.4 Failure Cause from GSM 04.08 recommendation (+CEER)


Cause
Diagnostic
value
1 Unassigned (unallocated) number
3 No route to destination
6 Channel unacceptable
8 Operator determined barring
16 Normal call clearing
17 User busy
18 No user responding
19 User alerting, no answer
21 Call rejected
22 Number changed
26 Non selected user clearing
27 Destination out of order
28 Invalid number format (incomplete number)
29 Facility rejected
30 Response to STATUS ENQUIRY
31 Normal, unspecified
34 No circuit/channel available
38 Network out of order
41 Temporary failure
42 Switching equipment congestion
43 Access information discarded
44 Requested circuit/channel not available

189
47 Resources unavailable, unspecified
49 Quality of service unavailable
50 Requested facility not subscribed
55 Incoming calls barred with in the CUG
57 Bearer capability not authorized
58 Bearer capability not presently available
63 Service or option not available, unspecified
65 Bearer service not implemented
68 ACM equal to or greater than ACMmax
69 Requested facility not implemented
70 Only restricted digital information bearer capability is available
79 Service or option not implemented, unspecified
81 Invalid transaction identifier value
87 User not member of CUG
88 Incompatible destination
91 Invalid transit network selection
95 Semantically incorrect message
96 Invalid mandatory information
97 Message type non-existent or not implemented
98 Message type not compatible with protocol state
99 Information element non-existent or not implemented
100 Conditional IE error
101 Message not compatible with protocol state
102 Recovery on timer expiry
111 Protocol error, unspecified
127 Interworking, unspecified

All other values in the range 0 to 31 shall be treated as cause 31.


All other values in the range 32 to 47 shall be treated as cause 47.
All other values in the range 48 to 63 shall be treated as cause 63.
All other values in the range 64 to 79 shall be treated as cause 79.
All other values in the range 80 to 95 shall be treated as cause 95.
All other values in the range 96 to 111 shall be treated as cause 111.
All other values in the range 112 to 127 shall be treated as cause 127.

190
18.5 Specific Failure Cause for +CEER
240 FDN is active and number is not in FDN
241 Call operation not allowed
252 Call barring on outgoing calls
253 Call barring on incoming calls
254 Call impossible
255 Lower layer failure

18.6 GSM 04.11 Annex E-2: Mobile originating SM-transfer


These error causes could appear for SMS commands (+CMGS, +CMSS, +CMGD…)

CAUSE NO 1: "Unassigned (unallocated) number"


This cause indicates that the destination requested by the Mobile Station cannot be
reached because, although the number is in a valid format, it is not currently assigned
(allocated).
CAUSE NO 8: "Operator determined barring"
This cause indicates that the MS has tried to send a mobile originating short message
when the MS's network operator or service provider has forbidden such transactions.
CAUSE NO 10: "Call barred"
This cause indicates that the outgoing call barred service applies to the short message
service for the called destination.
CAUSE NO 21: "Short message transfer rejected"
This cause indicates that the equipment sending this cause does not wish to accept this
short message, although it could have accepted the short message since the equipment
sending this cause is neither busy nor incompatible.
CAUSE NO 27: "Destination out of service"
This cause indicates that the destination indicated by the Mobile Station cannot be
reached because the interface to the destination is not functioning correctly. The term "not
functioning correctly" indicates that a signaling message was unable to be delivered to the
remote user; e.g., a physical layer or data link layer failure at the remote user, user
equipment off-line, etc.
CAUSE NO 28: "Unidentified subscriber"
This cause indicates that the subscriber is not registered in the PLMN (e.g.. IMSI not
known)
CAUSE NO 29: "Facility rejected"
This cause indicates that the facility requested by the Mobile Station is not supported by
the PLMN.
CAUSE NO 30: "Unknown subscriber"
This cause indicates that the subscriber is not registered in the HLR (e.g.. IMSI or directory
number is not allocated to a subscriber).
CAUSE NO 38: "Network out of order"
This cause indicates that the network is not functioning correctly and that the condition is
likely to last a relatively long period of time; e.g., immediately reattempting the short
message transfer is not likely to be successful.

191
CAUSE NO 41: "Temporary failure"
This cause indicates that the network is not functioning correctly and that the condition is
not likely to last a long period of time; e.g., the Mobile Station may wish to try another
short message transfer attempt almost immediately.
CAUSE NO 42: "Congestion"
This cause indicates that the short message service cannot be serviced because of high
traffic.
CAUSE NO 47: "Resources unavailable, unspecified"
This cause is used to report a resource unavailable event only when no other cause
applies.
CAUSE NO 69: "Requested facility not implemented"
This cause indicates that the network is unable to provide the requested short message
service.
CAUSE NO 81: "Invalid short message transfer reference value"
This cause indicates that the equipment sending this cause has received a message with a
short message reference which is not currently in use on the MS-network interface.
CAUSE NO 95: "Invalid message, unspecified"
This cause is used to report an invalid message event only when no other cause in the
invalid message class applies.
CAUSE NO 96: "Invalid mandatory information"
This cause indicates that the equipment sending this cause has received a message where
a mandatory information element is missing and/or has a content error (the two cases are
undistinguishable).
CAUSE NO 97: "Message type non-existent or not implemented"
This cause indicates that the equipment sending this cause has received a message with a
message type it does not recognize either because this is a message not defined or
defined but not implemented by the equipment sending this cause.
CAUSE NO 98: "Message not compatible with short message protocol state"
This cause indicates that the equipment sending this cause has received a message such
that the procedures do not indicate that this is a permissible message to receive while in
the short message transfer state.
CAUSE NO 99: "Information element non-existent or not implemented"
This cause indicates that the equipment sending this cause has received a message which
includes unrecognized information elements because the information element identifier is
not defined or it is defined but not implemented by the equipment sending the cause.
However, the information element is not required to be present in the message so that the
equipment sends the cause to process the message.
CAUSE NO 111: "Protocol error, unspecified"
This cause is used to report a protocol error event only when no other cause applies.
CAUSE NO 127: "Interworking, unspecified"
This cause indicates that there has been interworking with a network which does not
provide causes for actions it takes; thus, the precise cause for a message which is being
sent cannot be ascertained.
All values other than specified should be treated as error Cause No 41

192
18.7 Unsolicited result codes

Numeric
Verbose result code Description
(V0 set)
CALA: < time string>,<index> As verbose Alarm notification
+CBM: <length><pdu> (PDU) or
+CBM:<sn>,<mid>,<dcs>,<page>, As verbose Cell Broadcast Message
<pages>… (Text mode) directly displayed
+CBMI: “BM”,<index> As verbose Cell Broadcast Message
stored in mem at location <index>
+CCCM : <ccm> As verbose Current Call Meter value
+CCED: <values> As verbose Cell Environment
(specific) Description indication
+CCWA :<number>,<type>, As verbose Call Waiting number
<class> [,<alpha>]
+CDS: <fo>, <mr>… (text mode) As verbose SMS status report after
or +CDS: <length>,… (PDU) sending a SMS
+CDSI: <mem>,<index> As verbose Incoming SMS Status Report after
sending a SMS, stored in <mem>
(“SR”) at location <index>
+CKEV: <keynb> As verbose Key press or release
+CLIP : <number>, <type> [,,,<alpha>] As verbose Incoming Call Presentation
+CMT: <oa>… (text mode)
or +CMT: [<alpha>,]… (PDU) as verbose Incoming message directly displayed
+CMTI: <mem>,<index> as verbose Incoming message stored in
<mem> (“SM”) at location <index>
+CREG : <stat> [,<lac>,<ci>] As verbose Network registration indication
+CRING : <type> As verbose Incoming call type (VOICE, FAX ...)
+CSQ: <RxLev>,99 As verbose Automatic RxLev indication with
AT+CCED=1,8 command
+CSSU: <code2>[<number>,<type>] As verbose Supplementary service notification
during a call
+STIN: <ind> As verbose SIM Toolkit Indication
(specific)
+WIND: <IndicationNb> [,<CallId>] As verbose Specific unsolicited indication (SIM
(specific) Insert/Remove, End of init, Reset,
Alerting, Call creation/release)
+WVMI: <LineId>,<Status> As verbose
(specific) Voice Mail Indicator notification
(cf. +CPHS command)

193
+RUI: <UserInfo> As Verbose
(specific) Receive additional User Info on a MT
call setup, or a remote call release
RING 2 Incoming call signal from network

18.8 Final result codes

Numeric
Verbose result code Description
(V0 set)
+CME ERROR: <err> As verbose Error from GSM 07.05 commands
+CMS ERROR: <err> As verbose Error from SMS commands (07.07)
BUSY 7 Busy signal detected
ERROR 4 Command not accepted
NO ANSWER 8 Connection completion timeout
NO CARRIER 3 Connection terminated
OK 0 Acknowledges correct
execution of a command line
RING 2 Incoming call signal from network

18.9 Intermediate result codes

Numeric
Verbose result code Description
(V0 set)
+COLP :<number>,<type> as verbose Outgoing Call Presentation
+CR : <type> as verbose Outgoing Call report control
+ILRR: <rate> as verbose Local TA-TE data rate
CONNECT 300 10 Data connection at 300 bauds
CONNECT 1200 11 Data connection at 1200 bauds
CONNECT 1200/75 12 Data connection at 1200/75 bauds
CONNECT 2400 13 Data connection at 2400 bauds
CONNECT 4800 14 Data connection at 4800 bauds
CONNECT 9600 15 Data connection at 9600 bauds
CONNECT 14400 16 Data connection at 14400 bauds
+CSSI: <code1>[,<index>] As verbose Supplementary service notification
during a call setup

194
18.10 Parameters storage
Parameters storage mode
AT&W Command AT+CSAS AT&F
Command Default values
(E2P) (E2P) (SIM, E2P) (SIM, E2P)

General commands
+CSCS X X “PCCP437”
+WPCS X X “TRANSPARENT”
+CMEE X X 0
+CRSL X X 6

Call Control commands


%D X X 0
ATS0 X X 0 (no auto-answer)
+CICB X X 2 (speech)
+CSNS X X 0 (voice)
+VGR X X 64 (speaker 1)
32 (speaker 2)
+VGT X X 64 (mic 1 & ctrl 1)
0 (others)
+SPEAKER X X 0 (Spk 1 & Mic 1)
+ECHO X X ,1,0,3,10,7 (Algo ID 1)
,3,30,8000,256 (Algo ID 3)
+SIDET X X 1,1

Network Service commands


+COPS X X X 0,2
+CREG X X 0

Phonebook commands
+WAIP X X 0
+CSVM X X 0

195
Parameters storage mode
AT&W Command AT+CSAS AT&F
Command Default values
(E2P) (E2P) (SIM, E2P) (SIM, E2P)

SMS commands
+CSMS X 0
+CMGF X X 1 (text)
+CSDH X X 0
+CNMI X X 0,1,0,0,0
+CSMP X X 1,167,0,0
+CSCA X SIM dependant (phase 2)
+WUSS X X 0

Supplementary Services commands


+CCWA X X 0
+CLIP X X 0
+COLP X X 0
+CSSN X X 0,0
+CUSD X X 0
+CCUG X 0,0,0

Data commands
+CBST X X 0,0,1
+CR X X 0
+CRC X X 0
+ILRR X X 0
+CRLP X X 61,61,48,6,1
+DOPT X X 1,1
%C X X 2
+DS X X 3,0,4096,20
+DR X X 0
\N X X 0

196
Parameters storage mode
AT&W Command AT+CSAS AT&F
Command Default values
(E2P) (E2P) (SIM, E2P) (SIM, E2P)

Fax Class 2 commands


+FBOR X X 0
+FCQ X X 0
+FCR X X 1
+FDCC,+FDIS X X 0,5,0,0,2,0,0,0,0
+FPHCTO X X 30

V24 – V25 commands


+IPR X 9600
+ICF X 3,4
+IFC X 2,2
E X 1
&C X 1
&D X 1
&S X 1
Q X X 0
V X X 1
E X 1
wmux X X 0

197
Parameters storage mode
AT&W Command AT+CSAS AT&F
Command Default values
(E2P) (E2P) (SIM, E2P) (SIM, E2P)

Specific commands
+WIND X X 0
+ADC X X 0
+CMER X X 0
+WIOM X 255,0
+WVR X 5
+WDR X 2
+WSVG X X 0
+WRIM X X 0
+WCDM X X 0,0
+CPHS X X 0
+WBCM X X 0,0,4200,3300,100,5000,0
+WOPEN X 0
+WBM X 0,0 for SPI bus
0,4 for I2C Soft bus

SIM Toolkit commands


+STSF X 0,”160060C01F”,3,0

198
18.11 GSM sequences list
In accordance with GSM 02.30, the product supports the following GSM sequences, which
can be used through the ATD and the +CKPD commands.

18.11.1 Security
**04*OLDPIN*NEWPIN*NEWPIN# Change PIN code
**042*OLDPIN2*NEWPIN2*NEWPIN2# Change PIN2 code
**05*PUK*NEWPIN*NEWPIN# Unlock PIN code
**052*PUK2*NEWPIN2*NEWPIN2# Unlock PIN2 code
*#06# Show the IMEI number

18.11.2 Call forwarding


*SC# Activate
**SC*PhoneNumber# or Register and activate
**SC*PhoneNumber*BS# or
**SC*PhoneNumber*[BS]*T#
*#SC# or *#SC**BS# Check status
#SC#Deactivate
##SC# or ##SC**BS# Unregistered and deactivate

The Service codes (SC) are:


002 all call forwarding
004 all conditional call forwarding
21 call forwarding unconditional
61 call forwarding on no answer
62 call forwarding on not reachable
67 call busy

The Network service codes (BS) are:


No
All tele and bearer services
code
10 All teleservices
11 Telephony
12 All data teleservices
13 Fax services
16 Short Message Services
19 All teleservices except SMS

199
20 All bearer services
21 All asynchronous services
22 All synchronous services
24 All data circuit synchronous
25 All data circuit asynchronous
26 All dedicated packet access
27 All dedicated PAD access
The no reply condition timer (T), is only used for SC = 002, 004 or 61.

18.11.3 Call barring


*SC*Password# or *SC*Password*BS# Activate
*#SC# or *#SC**BS# Check status
#SC*Password# or #SC*Password*BS# Deactivate
**03*330*OLDPWD*NEWPWD*NEWPWD# Change password for call barring
**03**OLDPWD*NEWPWD*NEWPWD#
*03*330*OLDPWD*NEWPWD*NEWPWD#
*03**OLDPWD*NEWPWD*NEWPWD#

The Service codes (SC) are the followings:


33 call barring of outgoing call
330 all barring service (only for deactivation)
331 call barring of outgoing international call
332 call barring of outgoing international calls except to HPLMN
333 all outgoing barring service (only for deactivation)
35 call barring of incoming calls
351 call barring of incoming calls if roaming
353 all incoming barring service (only for deactivation)

The Network service codes (BS) are the same as these of the call forwarding sequences.

200
18.11.4 Call waiting
*43# Activate
*#43# Check status
#43# Deactivate

18.11.5 Number presentation


*#30# CLIP check status
*#31# CLIR check status
*31#PhoneNumber Invoke CLIR for a voice call
#31#PhoneNumber Suppress CLIR for a voice call
*#76# COLP check status

201
18.12 Operator names

Country MCC MNC Preferred Presentation of Country Initials Abbreviated Mobile


Initials and Mobile Network Name Network Name
A 232 01 A1 A1
A 232 03 A max. max.
A 232 05 one one
A 232 07 A tele.ring telering
AL 276 01 AMC-AL AMC
ALG 603 01 ALG RAMN AMN
AN 344 30 APUA PCS ANTIGUA APUA-PCS
AND 213 03 STA-MOBILAND M-AND
AUS 505 01 Telstra MNet Telstra
AUS 505 02 YES OPTUS Optus
AUS 505 03 VODAFONE AUS VFONE
AUS 505 08 One.Tel One.Tel
AZE 400 01 AZE-AZERCELL ACELL
AZE 400 02 AZE RBKCELL BKCELL
B 206 01 BEL PROXIMUS PROXI
B 206 10 B mobistar mobi*
BD 470 03 SHEBA SHEBA
BE 206 20 Orange Orange
BG 284 01 M-TEL GSM BG M-TEL
BGD 470 01 BGD-GP GP
BGD 470 02 BGD AKTEL AKTEL
BHR 426 01 BHR M-PLUS M.PLUS
BIH 218 03 BIH-ERONET ERONET
BIH 218 05 GSM-MS1 GSM-MS1
BIH 218 90 PTT-GSMBIH BHGSM
BRU 528 11 BRU-DSTCom DSTCom
BW 276 00 BW MASCOM MASCOM
BW 652 01 BW MASCOM MASCOM
BY 257 01 BY VELCOM VELCOM
CAN 302 37 CAN-MCELL MCELL
CH 228 01 SWISS GSM SWISS

202
CH 228 02 diAx Swiss diAx
CH 228 03 orange CH orange
CHN 460 00 CMCC CMCC
CHN 460 01 CHN-CUGSM CU-GSM
CHU 466 92 Chunghwa CHGHWA
CI 612 03 CI Ivoiris Ivoir
CI 612 05 TELECEL-Cl TELCEL
CL 730 01 CL ENTEL PCS ENTEL
CL 730 10 CL ENTEL PCS ENTEL
CMR 624 02 Mobilis CAM 02
CPV 625 01 CPV MOVEL CMOVEL
CY 280 01 CY CYTAGSM CY-GSM
CZ 230 01 CZ PAEGAS PAEGAS
CZ 230 02 EUROTEL - CZ ET - CZ
D 262 01 D1-TELEKOM T-D1
D 262 02 D2 PRIVAT D2
D 262 03 E-Plus E-Plus
D 262 07 D Interkom Ik
DK 238 01 DK TDK-MOBIL TD MOB
DK 238 02 DK SONOFON SONO
DK 238 20 TELIA DK TELIA
DK 238 30 DK Mobilix #mbix
DO 370 01 orange orange
E 214 01 E AIRTEL AIRTL
E 214 02 MOVISTAR MSTAR
E 214 03 E AMENA AMENA
E 214 07 MOVISTAR MSTAR
EE 248 01 EE EMT GSM EMT
EE 248 02 EE RLE RLE
EE 248 03 EE Q GSM Q GSM
EGY 602 01 EGY MobiNiL MobiNiL
EGY 602 02 EGY CLICK CLICK
ETH 636 01 ETH-MTN ET-MTN
F 208 01 Orange F Orange

203
F 208 10 F SFR SFR
F 208 20 BOUYGTEL BYTEL
F 340 01 F AMERIS AMERIS
F 547 20 F-VINI VINI
F 647 10 SFR REUNION SFR RU
FI 244 03 FI TELIA TELIA
FI 244 05 FI RL RL
FI 244 09 FI FINNET FINNET
FI 244 91 FI SONERA SONERA
FIJ 542 01 VODAFONE FIJ VODAFJ
GEO 282 01 GEO-GEOCELL GCELL
GEO 282 02 MAGTI-GEO MAGTI
GH 620 01 GH SPACEFON SPACE
GH 620 02 GH GTGSM GTGSM
GIB 266 01 GIBTEL GSM GIBTEL
GN 611 02 GN LAGUI LAGUI
GR 202 01 GR COSMOTE C-OTE
GR 202 05 GR PANAFON PAN
GR 202 10 GR TELESTET TLSTET
H 216 01 H PANNON GSM PANNON
H 216 30 H-WESTEL 900 W-900
H 216 70 Vodafone H-70
HK 454 00 CSL CSL
HK 454 04 HK Orange ORANGE
HK 454 06 HK SMC HKSMC
HK 454 10 NEW WORLD NWPCS
HK 454 12 PEOPLES PEOPLES
HK 454 16 SUNDAY SUNDAY
HR 219 01 HR-CRONET CRON
HR 219 10 HR-VIPNET VIP
I 222 01 I TIM TIM
I 222 10 I OMNITEL OMNI
I 222 88 I WIND I WIND
I 222 98 I BLU BLU

204
IL 425 01 IL ORANGE ORANGE
INA 404 01 ESSARH ESSARH
INA 404 07 INA TATA TATA
INA 404 10 INA-AIRTL AIRTL
INA 404 11 INA ESSAR ESSAR
INA 404 12 INA - ESCOTEL ESCOTL
INA 404 14 MODICOM INA MODICO
INA 404 15 ESSARU ESSARU
INA 404 20 INA MaxTouch MAXTCH
INA 404 21 BPL MOBILE BPL MOBILE
INA 404 27 BPL MOBILE BPL MOBILE
INA 404 30 INA COMMAND COMMND
INA 404 41 INA RPG RPG
INA 404 42 INA AIRCEL AIRCEL
INA 404 43 BPL MOBILE BPL MOB
INA 404 46 BPL MOBILE BPL MOB
INA 404 60 ESSARR ESSARR
IND 404 44 IN-44 SPICE
IND 510 01 IND SAT-C SAT-C
IND 510 10 IND RT-SEL T-SEL
IND 510 11 IND GSM-XL EXCEL
IRL 272 01 IRL Eircell Eircell
IRL 272 02 IRL DIGIFONE DIGI
IS 274 01 IS SIMINN SIMINN
IS 274 02 IS TAL TAL
JOR 416 01 Fastlink FSTLNK
KGZ 437 01 BITEL KGZ BITEL
KHM 456 01 MOBITEL-KHM MT-KHM
KHM 456 02 KHM-SM KHM-SM
KSA 420 01 ALJAWWAL KSA
KSA 420 07 EAE-ALJAWWAL EAE
KT 419 02 KT MTCNet MTC
KT 419 03 KT WATANIYA WATANIYA
KZ 401 01 KZ K-MOBILE K-MOBILE

205
KZ 401 02 KZ KCELL KCELL
L 270 01 L LUXGSM LUXGSM
L 270 77 L TANGO TANGO
LAO 457 01 LAO GSM LAO GSM
LBR 618 01 LBR OMEGA OMEGA
LSO 651 01 VCL COMMS VCLCOM
LT 246 02 LT BITE GSM BITE
LTU 246 01 OMNITEL LT OMT
LV 247 01 LV LMT GSM LMT
LV 247 02 LV BALTCOM B-COM
M 278 01 VODAFONE MLA VODA M
MAC 455 01 MAC-CTMGSM CTMGSM
MD 259 01 MD VOXTEL VOXTEL
MDG 642 02 MDG-ANTARIS ANTARI
MKD 294 01 MKD-MOBIMAK MOBI-M
MOR 604 00 Meditel MEDITEL
MOR 604 01 MOR IAM IAM
MOZ 643 01 MOZ-mCel mCel
MRU 617 01 CELLPLUS-MRU CELL +
MRU 617 10 EMTEL-MRU EMTEL
MV 472 01 MV DHIMOBILE D-MOBILE
MW 650 01 MW CP 900 CP 900
MW 650 10 CELTEL MW CELTEL
MY 502 12 MY Rmaxis maxis
MY 502 13 TMTOUCH TMTOUCH
MY 502 16 MY DIGI 1800 MT18
MY 502 17 MY-ADAM 017 ADAM
MY 502 19 MY CELCOM CELCOM
N 242 01 N Telenor TELENOR
N 242 02 N NetCom GSM N COM
NCL 546 01 NCL MOBILIS MOBNCL
NL 204 04 NL LIBERTEL LIBTEL
NL 204 08 NL KPN NL KPN
NL 204 12 NL TELFORT TELFORT

206
NL 204 16 Ben NL Ben NL
NL 204 20 Dutchtone Dtone
NZ 530 01 VODAFONE NZ VODA
OMN 422 02 OMAN MOBILE OMAN
P 268 01 P TELECEL TLCL
P 268 03 P OPTIMUS OPTIM
P 268 06 P TMN TMN
PGY 744 01 HOLA PARAGUAY S.A. HPGYSA
PGY 744 01 HOLA PARAGUAY S.A. HPGYSA
PH 515 01 ISLACOM ISLA
PH 515 02 GLOBE PH GLOBE
PH 515 03 PH SMART SMART
PL 260 01 PL-PLUS PLUS
PL 260 02 PL-ERA GSM ERAGSM
PL 260 03 PL-IDEA IDEA
PSE 425 05 JAWWAL-PALESTINE JAWWAL
QAT 427 01 QAT-QATARNET Q-NET
R 635 10 R-CELL RCELL
RA 283 01 RA-ARMGSM ARMMO1
RL 415 01 RL Cellis CLLIS
RL 415 03 RL LibanCell LibCL
RO 226 01 RO CONNEX CONNEX
RO 226 10 RO dialog dialog
RUS 250 01 MTS-RUS MTS
RUS 250 02 NWGSM RUS NWGSM
RUS 250 05 SCS RUS SCS
RUS 250 07 RUS BMT BMT
RUS 250 12 Far East RUS FEast
RUS 250 13 KUGSM KUGSM
RUS 250 17 RUS 17 ERMAK
RUS 250 28 EXTEL RUS EXTEL
RUS 250 39 Uraltel UTL
RUS 250 44 NC-GSM NC-GSM
RUS 250 93 --- ---

207
RUS 250 99 BEE L Bee Line
S 240 01 TELIA TELIA
S 240 07 S COMVIQ IQ
S 240 08 EURO EURO
SA 655 01 VodaCom-SA VODA
SA 655 10 MTN-SA MTN
SDN 634 01 SDN MobiTel SD-MOB
SEZ 633 01 SEZ SEYCEL SEYCEL
SEZ 633 10 SEZ AIRTEL AIRTEL
SGP 525 01 ST-GSM-SGP STGSM
SGP 525 02 GSM1800 GSM1800
SGP 525 03 M1-GSM-SGP M1-GSM
SGP 525 05 STARHUB-SGP STARHUB
SI 293 40 SI.MOBIL SI.MOBIL
SI 293 41 SI SI-GSM SI-GSM
SK 231 01 SVK GT SVK GT
SK 231 02 EUROTEL-SK ET-SK
SN 608 01 SN ALIZE ALIZE
SN 608 02 SENTEL SENTEL
SRI 413 02 SRI DIALOG DALOG
SRI 413 03 SRI - CELLTEL CELLTEL
SYR 417 09 SYR MOB SYR MOBILE
SZ 653 10 Swazi-MTN SwaziMTN
TG 615 01 TG-TOGO CELL TGCELL
TH 520 01 TH AIS GSM TH AIS
TH 520 10 TH ORANGE ORANGE
TH 520 18 TH-DTAC DTAC
TH 520 23 TH-HELLO HELLO
TN 605 02 TUNISIE TELECOM TT
TR 286 01 TR RTCELL TCELL
TR 286 02 TR TELSIM TELSIM
TWN 466 01 FarEastone FET
TWN 466 06 TWN TUNTEX TUNTEX
TWN 466 88 KGT-ONLINE KGT

208
TWN 466 93 Mobitai TW MOB
TWN 466 97 TWN GSM PCC
TWN 466 99 TransAsia
TZ 640 01 Tritel-TZ TRITEL
TZ 640 03 ZANTEL-TZ ZANTEL
UA 255 01 UA UMC UMC
UA 255 03 UA-KYIVSTAR UA-KS
UA 255 05 UA-GOLDEN UA-GT
UAE 424 02 UAE ETISALAT ETSLT
UG 641 01 UG CelTel CELTEL
UG 641 10 MTN-UGANDA MTN-UG
UK 234 10 BTCELLNET BTCNET
UK 234 15 UK VODAFONE VODA
UK 234 30 one2one ONE2ONE
UK 234 33 ORANGE ORANGE
UK 234 50 JT GSM JT GSM
UK 234 55 GSY-TEL GSY-TEL
UK 234 58 MANX MANX
UKR 255 02 FLASH-UKR FLASH
USA 310 10 USA MCI ---
USA 310 11 USA Wireless 2000 Telepho WTTCKy
USA 310 12 USA D&E Com ---
USA 310 13 USA MobileTel ---
USA 310 20 USA Sprint ---
USA 310 30 USA PCS PRIME ---
USA 310 31 USA-AERIAL AERIAL
USA 310 40 USA PCS PRIME ---
USA 310 50 USA PCS PRIME ---
USA 310 60 USA PCS PRIME ---
USA 310 70 USA PCS PRIME ---
USA 310 80 USA PCS PRIME ---
USA 310 90 USA PCS PRIME ---
USA 310 100 USA PCS PRIME ---
USA 310 110 USA Wireless 2000 Telepho WTTCKy

209
USA 310 120 USA PCS PRIME ---
USA 310 130 USA PCS PRIME ---
USA 310 140 USA PCS PRIME ---
USA 310 150 BellSouth Mobility DCS BSMDCS
USA 310 160 USA OMNIPOINT ---
USA 310 170 USA PAC BELL ---
USA 310 180 USA PAC BELL ---
USA 310 190 USA COX ---
USA 310 200 VoiceStream VStream
USA 310 210 VoiceStream VStream
USA 310 220 VoiceStream VStream
USA 310 230 VoiceStream VStream
USA 310 240 VoiceStream VStream
USA 310 250 VoiceStream VStream
USA 310 260 VoiceStream VStream
USA 310 270 USA Powertel, Inc. USA27
USA 310 280 USA PowerTel ---
USA 310 290 USA PowerTel ---
USA 310 300 USA Aerial ---
USA 310 310 USA-AERIAL AERIAL
USA 310 320 USA Aerial ---
USA 310 330 USA Aerial ---
USA 310 340 USA Aerial ---
USA 310 350 USA Aerial ---
USA 310 380 USA Pocket ---
USA 310 390 USA Pocket ---
USA 310 400 USA Pocket ---
USA 310 410 USA Pocket ---
USA 310 420 USA Pocket ---
USA 310 430 USA Pocket ---
USA 310 440 USA Pocket ---
USA 310 450 USA Pocket ---
USA 310 460 USA OMNIPOINT ---
USA 310 470 USA OMNIPOINT ---

210
USA 310 480 USA OMNIPOINT ---
USA 310 490 USA OMNIPOINT ---
USA 310 500 USA OMNIPOINT ---
USA 310 510 USA OMNIPOINT ---
USA 310 520 USA OMNIPOINT ---
USA 310 530 USA OMNIPOINT ---
USA 310 540 USA OMNIPOINT ---
USA 310 550 USA OMNIPOINT ---
USA 310 560 USA OMNIPOINT ---
USA 310 570 USA OMNIPOINT ---
USA 310 580 USA OMNIPOINT ---
USA 310 610 USA OMNIPOINT ---
USA 310 620 USA OMNIPOINT ---
USA 310 630 USA OMNIPOINT ---
USA 310 640 USA Einstein ---
USA 310 660 USA DiGiPH ---
USA 310 670 USA WTTCKy ---
USA 310 680 USA NPI ---
USA 310 690 USA Conestoga ---
USA 310 770 Iowa Wireless USA IWS
USA 310 790 USA PinPoint Wireless PnPt
UZB 434 04 UZB DAEWOO DW-GSM
UZB 434 05 UZB CSOCOM COSCOM
VN 452 01 VN Mobi Fone VMS
VN 452 02 VN VINAFONE GPC
VZ 734 01 VZ INFO INFONT
VZ 734 02 DIGITEL DIGITEL
YU 220 01 YU MOBTEL MOBTEL
ZW 648 01 ZW NET*ONE NET*1

211
18.13 Data / Commands multiplexing protocol

18.13.1 Introduction
The Wavecom multiplexing protocol operates between a DCE (Data Communication
Equipment: the product) and a DTE (Data Terminal Equipment). It allows a double session
over a serial link interface : one for AT commands and one for DATA communications.
AT+WMUX=1 activates the Multiplexing Mode. With this mode, AT commands and DATA
are encapsulated into packets. The header of these packets allows to recognize whether it
is a DATA packet or an AT command packet. AT+WMUX=0 deactivates the Multiplexing
Mode and gets the product back to the default mode.
This appendix presents how the multiplexing mode handles the DATA and the AT
commands flow. It also describes the format of DATA packets and AT command packets.

18.13.2 AT command packets


An AT command is encapsulated into a packet with a header which allows to separate it
from DATA packets. This packet is formed by a header (3 bytes), the AT command itself
and a checksum (1 byte):

b7 b6 b5 b4 b3 b2 b1 b0
Start pattern ➡ 0xAA
AT command length LSB
AT command pattern ➡ 0x1D AT command length MSB
AT command
Checksum

The 3 bytes of the header are:


❑ the first byte (0xAA) is used to identify the packet,
❑ the second byte represents the 8 LSB (Low Significant Bits) bits of the length of
the AT command,
❑ the third byte is made of 2 parts :
- the 3 LSB bits are the 3 MSB (Most Significant Bits) bits of the length of the
AT command,
- the 5 MSB bits (0x1D which equals to 0xE8 with the 3 bits offset) are used to
identify an AT command.

The maximum length of an AT command could be 2047 bytes which is greater than all the
existing AT commands.

The checksum is the addition (modulo 256) of all the transmitted bytes (header bytes and
AT command bytes).

212
18.13.3 Data packets
Like for AT commands, DATA are encapsulated into packets. These packets are composed
of a header (3 bytes), the data bytes and the checksum (1 byte):

b7 b6 b5 b4 b3 b2 b1 b0
Start pattern ➡ 0xDD
Data packet length LSB
Data packet type Data packet length MSB
Data Bytes
Checksum

The 3 bytes of the header are:


❑ the first byte (0xDD) used to identify the packet,
❑ the second byte represents the 8 LSB bits of the length of the data field,
❑ the last byte is made of 2 parts :
- the 3 LSB bits represent the 3 MSB bits of the length of the data field,
- the 5 MSB bits represent the packet type.

Data packets can have different values according to the type of packet:
❑ 0 – DATA packet : the packet contains the data to transmit on the radio link or
received from the radio link,
❑ 1 – STATUS packet: the packet contains the status of SA, SB, X bits( ) and the
break condition coding as follow :

SA SB X BRK RI Spare Spare Spare


- the length of data for the status packet is always equal to 1,
- whenever a status changes (except break), all the status bits are included,
- these bits are off by default (and therefore the bits DTR and RTS), so it is
necessary to send a status packet to the target at the beginning of the
multiplexing to start the transmission,
❑ 2 – READY packet : the packet indicates that the target is ready to receive data :
- no data are transmitted in this packet (so the length is null),
❑ 3 – BUSY packet : the packet indicates that the target is busy and can not receive data :
- like the ready packet, no data are transmitted,
❑ other values currently, these values are not used (reserved for future
enhancement).

The checksum is calculated like the AT command packet checksum (addition of all the
transmitted bytes including the header bytes).

213
18.13.4 Examples

18.13.4.1 AT command and its answer


When there is no encapsulation the AT command transmitted on the serial link is like this
(in ASCII and hexadecimal):

AT\r\n 0x41 0x54 0x0D 0x0A


and the answer is like this :
\r\nOK\r\n 0x0D 0x0A 0x4F 0x4B 0x0D 0x0A

With the encapsulation in the serial link, the packet transmitted is (in hexadecimal) :
0xAA 0x04 0xE8 0x41 0x54 0x0D 0x0A 0x42

and the answer is like this :


0xAA 0x06 0xE8 0x0D 0x0A 0x4F 0x4B 0x0D 0x0A 0x60

18.13.4.2 Initialisation and Data packet


When the Multiplexing Mode is activated (+WMUX=1), the product sends 2 Data packets
after the establishment of a DATA call (after the CONNECT xxxx message) : 1 READY
Packet and 1 STATUS Packet. To set the different signals to the right value, it is necessary
to send a STATUS packet to the product.

Here are some examples of STATUS packets :


0xDD 0x01 0x08 0x40 0x26 bit RTS is on
to start a data call, all the bits should be on :
0xDD 0x01 0x08 0xC0 0xA6 bits DTR and RTS are on

18.13.5 Restriction
The autobauding mode is not available when the Multiplexing Mode is activated : the
serial link speed must be set to a fixed rate.

214
19 APPENDIX A (informative)
This chapter gives illustrative examples of the general AT commands used for a
communication.

19.1 Examples with the PIN required


Example 1 : when the ME is powered off.

AT+CMEE=1 Enable the report mobile equipment errors


OK
AT+CREG=1 Report registration
OK
AT+CPAS Query ME Status
+CPAS: 5 (ME is asleep)
OK
AT+CFUN=1 Set ME to full functionality
OK
AT+COPS=0 Ask for automatic operator selection and registration.
+CME ERROR: 11 SIM PIN required.
AT+CPIN=1234 User entered a wrong PIN
+CME ERROR: 16 Incorrect password.
AT+CPIN=0000
OK PIN Ok
AT+COPS=0 Ask for automatic operator selection and registration.
OK
+CREG:1 Registered on the network
AT+COPS=3,0 Select the long name alphanumeric format.
OK
AT+COPS? Get the operator name
+COPS: 0,0,”I OMNITEL”
OK
Example 2: When the ME has already been powered on.

AT+CMEE=1 Enable the report mobile equipment errors


OK
AT+CPAS Get the ME Status
+CPAS: 0 ME is ready to receive commands
OK
AT+CPIN? Is ME requiring a password?
+CPIN: SIM PIN Yes, SIM PIN required
AT+CPIN=0000
OK PIN Ok

215
19.1.1 Examples where a voice call is originated.
Example 3 : When the ME is powered on and the SIM PIN has been entered.

AT+CMEE=1 Enable the reporting of mobile equipment errors


OK
AT+WIND=63 Ask to display the general indications.
OK
AT+CPIN? Is ME requiring a password?
+CPIN: READY product is ready
ATD0607103543; Make a voice call
+WIND: 5,1 Indication of call
+WIND: 2 Remote party is ringing.
OK Call setup was successful
Conversation…
ATH Release the call
OK

When a voice call is attempted from a phonebook :

ATD>”John Pamborn”;
+CME ERROR: 22 The “John Pamborn” entry is not found.
ATD>”Joel Guerry”;
+WIND: 5,1 Indication of outgoing call.
+WIND: 2 Remote party is ringing.
OK Call setup was successful
Conversation…
ATH Release the call
OK

19.1.2 Example with incoming calls


When the ME is powered on and the SIM PIN has been entered.

AT+CMEE=1 Enable the report mobile equipment errors


OK
AT+WIND=63 Ask to display the general indications.
OK
AT+CLIP=1 Enable the calling line identification presentation.
OK
AT+CRC=1 Enable extended format of incoming indication.
OK

216
AT+CNUM Query own number (voice number) or MSISDN.
+CNUM: “Speech”,”+33608971019”,145
OK
Call the number from another ME.

+WIND: 5, 1 Indication of call (Ring)


+CRING: VOICE Type of call is VOICE.
+CLIP: "+33607103543",145,,,"John Panborn" Identification of the remote party.
+CRING: VOICE
ATA Answer the call.
OK
…Conversation…
NO CARRIER The call has been released by the remote party.
+WIND: 6,1 Indication of call release.

19.1.3 Example of a call forwarding


When the ME is powered on and the SIM PIN has been entered.

AT+CMEE=1 Enable the report mobile equipment errors


OK
AT+CFCC=1,3,”0607492638” Register to a call forwarding when ME is busy.
OK
AT+CCFC=2,3,”0149293031”,129 Register to a call forwarding when it does answer.
+CME ERROR: 30 No network service
AT+CCFC=1,2 Interrogate
+CCFC: 1,1,”+33607492638”,145 Call forwarding active for a voice call.
AT+CFCC=1,4 Delete call forwarding ME busy
OK

19.1.4 Example of a multiparty call


When the ME is powered on and the SIM PIN has been entered.

AT+CMEE=1 Enable the report mobile equipment errors


OK
AT+WIND=63 Ask to display the general indications.
OK
AT+CCWA=1,1 Enable call waiting.
OK
ATD>”John Panborn”;
+WIND: 5,1 Indication of call.
+WIND: 2 Remote party is ringing.

217
OK Call setup was successful
…Conversation…
+WIND: 5,2 Indication of another call.
+CCWA: “+33595984834”,145,”Dolores Claiborne” Another call is waiting.
AT+CHLD=2 Put first call on hold and answer the second one.
OK
…Conversation…
AT+CHLD=3 Every call is part of a multiparty conversation.
OK
AT+CHLD=11 Release the first call (with John Panborn) and recover the second call (with Dolores Claiborne)
…Conversation …
ATH Release the second call.

19.2 Examples about phonebooks


For each example illustrated in this section: at the beginning the ME is powered on and the
SIM PIN has been entered.

19.2.1 Example 1 : The whole phonebook of the ME is read

AT+CPBS=? Query supported phonebook memories


+CPBS: (“SM”,”FD”,”ON”) ADN, FDN, and MSISDN phonebooks supported.
AT+CPBS=”SM” Select ADN phonebook..
OK
AT+CPBR=? Read the index range and the length of the elements.
+CPBR: (1-80),20,14 80 locations (from 1 to 80), max length of 20 for the phone number, 14 characters max
for the text.
AT+CPBR=1,80 Read all entries (only the ones set are returned).
+CPBR: 1,“0346572834”,129,”Dolores Claiborne”
+CPBR: 2,”1284374523”,129,”Thad Beaumont”
+CPBR: 3, “1243657845”,129,”John Panborn”
OK

19.2.2 Example 2 : Erase or Write a phonebook entry

AT+CPBW=? Get the phonebook type.


+CPBW: (1-80),20,(129,145),14 80 locations, max length of 20 for the phone number,
TON/NPI of 129 or 145 and 14 characters max for the text.
AT+CPBW=3 Erase location 3
OK
AT+CPBW=3,”4356729012”,129,”Carry” Write at location 3.
Ok
AT+CPBR=1,80 Read all entries (only the ones set are returned).

218
+CPBR: 1,“0346572834”,129,”Dolores Claiborne”
+CPBR: 2,”1284374523”,129,”Thad Beaumont”
+CPBR: 3,”4356729012”,129,”Carry”
OK

19.2.3 Example 3 : Find phonebook entries

AT+CPBF=? Get the phonebook type.


+CPBF: 20,14 Max length of 20 for the phone number, 10 characters for the text.
AT+CPBF=”D” Read entries starting with “D”.
+CPBF: 1,“0346572834”,129,”Dolores Clairborne”
OK
AT+CPBF=”W” Read entries with “W”.
+CME ERROR: 22 Entry not found.

19.2.4 Example 4 : Phonebook and custom character set

AT+CPBS? Query the current phonebook


+CPBS: 3,80 ADN selected, 3 entries stored
OK
AT+WPCS? Query the current phonebook charset
+WPCS: “TRANSPARENT” Transparent mode selected
OK
AT+CPBR=1
+CPBR: 1,”0146290800”,129,”S bastien” GSM character “é” is not displayed
OK
AT+WCCS=1,0,0,255
>202020202020202020200A20200D202020202020205F20202020202020202020202122230
225262728292A2B2C2D2E2F303132333435363738393A3B3C3D3E3F004142434445464748
494A4B4C4D4E4F505152535455565758595A2020202011206162636465666768696A6B6C6
D6E6F707172737475767778797A20202020202020202020202020202020202020202020272
720202020202020202020202020204020012403205F20202020202D2020202020202720202
02020202020202060414141415B0E1C09451F454549494949445D4F4F4F4F5C200B5555555
E59201E7F6161617B0F1D630405656507696969207D086F6F6F7C200C0675757E792079
OK
AT+WCCS=1,1,0,127
>40A324A5E8E9F9ECF2C70AD8F80DC5E5205F20202020202020202020C6E6DFC920212
223A425262728292A2B2C2D2E2F303132333435363738393A3B3C3D3E3FA14142434445
464748494A4B4C4D4E4F505152535455565758595AC4D6D1DCA7BF61626364656667686
96A6B6C6D6E6F707172737475767778797AE4F6F1FCE0
OK Set the custom character set tables to enable a GSM to default font conversion

219
AT+WPCS=”CUSTOM” Use the custom character set
OK
AT+CPBR=1
+CPBR: 1,”0146290800”,129,”Sébastien” GSM character “é” is correctly displayed
OK

19.3 Examples about short messages

19.3.1 Example 4 : Send a short message

AT+CNMI=0,1,1,1,0 SMS-DELIVERs are directly stored, SMS-STATUS- REPORTs are displayed


OK
AT+CSMP=17,169,0,0 SMS-SUBMIT message with a validity period (one day)
OK
AT+CMGF=1 ” ” Text mode to send a Short Message
OK
AT+CSCA=”+33608080706” Set Service Center Address to +33608080706
OK
AT+CMGS=0601290800 Send a SMS-SUBMIT to mobile phone
Product sends a 4 characters sequence: 0x0D 0x0A 0x3E 0x20
This is the first text line Edit first line and press carriage return (<CR>, 0x0D)
This is the last text line Edit last line and send message by pressing <ctrl-Z> (0x1A)
+CMGS: 5 Success: message reference 5 is returned from the SMS Service Center
+CDS: 2,5,”0601290800”,129,”99/05/01 14:15:10+04 ” ” ” ” Success: report of
successful message delivery received

19.3.2 Example 5: Read short messages

AT+CMGF=1 Text mode to read Short Messages


AT+CMGL=”ALL” List all stored messages
+CMGL: 1,”REC READ”,”+336290918”,,”99/05/01 14:15:10+04” This is the first message
+CMGL: 2,”REC UNREAD”,”+336290918”,,”99/05/01 14:19:44+04” This is the second message
OK
AT+CMGR=1 ” ” Read the first message
+CMGR: ”REC READ”,”+336290918”,,”99/05/01 14:19:44+04”
OK

220
19.4 Examples about Fax class 2
The normal characters are generated DTE. The bold characters are modem generated.

19.4.1 Example 1 : Send a fax class 2

AT+FCLASS=2 Select fax class 2


OK
AT+FLID="LocalFax"
OK
ATD0601234567 Call establishment
+FCON Connection OK
[+FCSI:"RemoteFax"]
+FDIS:0,3,0,2,0,0,0,0
OK
AT+FDT Beginning of the data transfer
+FDCS:0,3,0,2,0,0,0,0
CONNECT
<0x11h> Send carrier
First page data terminated by <0x10h><0x03h>
OK Page transmitted
AT+FET=0 Send another page
+FPTS:1 First page acquitted
OK
AT+FDT
CONNECT
<0x11h> Send carrier
Second page data terminated by <0x10h><0x03h>
OK Page transmitted
AT+FET=2 No more page
+FPTS:1 First page acknowledged
+FHNG:0 Normal end of connection
OK

221
19.4.2 Example 2: Receive a fax class 2

AT+FCR=1
OK
AT+FLID="LocalFax"
OK
RING Incoming call
ATA Answer
+FCON Connection OK
[+FTSI:"RemoteFax"]
+FDCS:0,3,0,2,0,0,0,0
OK
AT+FDR
+FCFR
+FDCS:0,3,0,2,0,0,0,0
CONNECT
<0x12h> Receive page carrier
First page data terminated by
<0x10h><0x03h>
OK Page received
+FPTS:1 First page acknowledged
FET:0 To receive another page
OK
AT+FDR
+FDCS:0,3,0,2,0,0,0,0
CONNECT
<0x12h> Receive page carrier
Second page data terminated by
<0x10h><0x03h>
OK Page received
+FPTS:1 First page acknowledged
+FET:2 No more page to receive
OK
AT+FDR
+FHNG:0 Normal end of connection
OK

222
20 APPENDIX B:
Support of SIM ToolKit by The M.E.
TABLE 1 – Support of SIM Toolkit classes
This has been extracted from the 11.14.
Classes
Command description 1 2 3
CALL CONTROL X X
CELL BROADCAST DOWNLOAD X X
DISPLAY TEXT X X
EVENT DOWNLOAD
- MT call X
- Call connected X
- Call disconnected X
- Location status X
- User activity X
- Idle screen available X
GET INKEY X X
GET INPUT X X
GET READER STATUS $(MultipleCard)$ Lc
MENU SELECTION X X
MO SHORT MESSAGE CONTROL X
MORE TIME X X
PERFORM CARD APDU $(MultipleCard)$ Lc
PLAY TONE X X
POLLING OFF X X
POLL INTERVAL X X
POWER ON CARD $(MultipleCard)$ Lc
POWER OFF CARD $(MultipleCard)$ Lc
PROVIDE LOCAL INFORMATION X X
REFRESH X X X
RUN AT COMMAND $(AT$) Lc
SELECT ITEM X X
SEND SHORT MESSAGE X X
SEND SS X X

223
SEND USSD X
SET UP CALL X X
SET UP EVENT LIST X
SET UP IDLE MODE TEXT $(IdleModeText)$ X
SET UP MENU X X
SMS-PP DOWNLOAD X X X
TIMER MANAGEMENT $(Timer)$ Lc
TIMER EXPIRATION $(Timer)$ Lc

TABLE 2 - Compatibility between available Terminal Responses and Proactive Commands

Proactive commands
Terminal Menu Display Get Get Setup Play Select Send Send Send Setup
Refresh
Reponses Setup Text Inkey Input Call Tone Item SS SMS USSD event
(0) (1) (2) (3) (4) (5 (6) (7) (8) (9) (10) list (11)
Backward
Move ● ● ● ●
(95)
Command
beyond ME ● ● ● ● ● ● ● ● ● ● ● ●
capabilities (96)
ME currently
unable to process ● ● ● ● ● ● ● ● ● ● ● ●
command (97)
No response
from the user ● ● ● ●
(98)
SIM session
terminated ● ● ● ● ● ●
by the user (99)

224
21 APPENDIX C:
Structure of TERMINAL PROFILE
First byte (Download):

b8 b7 b6 b5 b4 b3 b2 b1
Profile download User choice
SMS-PP data download Set by product to 1
Cell Broadcast data download Set by product to 1
Menu selection User choice
'9E XX' response code for SIM
data download error Set by product to 1
Timer expiration Set by product to 0
USSD string data object supported
in Call Control User choice
RFU, bit=0

Second byte (Other):

b8 b7 b6 b5 b4 b3 b2 b1
Command result User choice
Call Control by SIM User choice
Cell identity included in Call
Control by SIM User choice
MO short message control by SIM User choice
Handling of the alpha identifier
according to subclause 9.1.3 User choice
UCS2 Entry supported User choice
UCS2 Display supported User choice
Display of the extension text User choice

Third byte (Proactive SIM):

b8 b7 b6 b5 b4 b3 b2 b1
Proactive SIM: DISPLAY TEXT User choice
Proactive SIM: GET INKEY User choice
Proactive SIM: GET INPUT User choice
Proactive SIM: MORE TIME User choice
Proactive SIM: PLAY TONE User choice
Proactive SIM: POLL INTERVAL Set by product to 1
Proactive SIM: POLLING OFF Set by product to 1
Proactive SIM: REFRESH User choice

225
Fourth byte (Proactive SIM):

b8 b7 b6 b5 b4 b3 b2 b1
Proactive SIM: SELECT ITEM User choice
Proactive SIM: SEND SHORT MESSAGE User choice
Proactive SIM: SEND SS User choice
Proactive SIM: SEND USSD User choice
Proactive SIM: SET UP CALL User choice
Proactive SIM: SET UP MENU User choice
Proactive SIM: PROVIDE LOCAL INFORMATION
(MCC, MNC, LAC, Cell ID & IMEI) Set by product to 1
Proactive SIM: PROVIDE LOCAL INFORMATION
(NMR) Set by product to 1

Fifth byte (Event driven information):

b8 b7 b6 b5 b4 b3 b2 b1
Proactive SIM: SET UP EVENT LIST Set by product to 1
Event: MT call Set by product to 1
Event: Call connected Set by product to 1
Event: Call disconnected Set by product to 1
Event: Location status Set by product to 1
Event: User activity User choice
Event: Idle screen available User choice
Event: Card reader status Set by product to 0

Sixth byte: (reserved for Event driven information extensions)

b8 b7 b6 b5 b4 b3 b2 b1
RFU, bit = 0

Seventh byte: (Multiple card proactive commands) for class "a"

b8 b7 b6 b5 b4 b3 b2 b1
Proactive SIM: POWER ON CARD Set by product to 0
Proactive SIM: POWER OFF CARD Set by product to 0
Proactive SIM: PERFORM CARD APDU Set by product to 0
Proactive SIM: GET READER STATUS Set by product to 0
RFU, bit = 0 Set by product to 0

226
Eighth byte (Proactive SIM):

b8 b7 b6 b5 b4 b3 b2 b1
Proactive SIM: TIMER MANAGEMENT
(start, stop) Set by product to 1
Proactive SIM: TIMER MANAGEMENT
(get current value) Set by product to 1
Proactive SIM: PROVIDE LOCAL INFORMATION
(date, time and time zone) Set by product to 0
Binary choice in GET INKEY Set by product to 0
SET UP IDLE MODE TEXT Set by product to 0
RUN AT COMMAND
(e.g.. class "b" is supported) Set by product to 0
2nd alpha identifier in SET UP CALL Set by product to 0
2nd capability configuration parameter
(see 9.1.6) Set by product to 0

Ninth byte:

b8 b7 b6 b5 b4 b3 b2 b1
Sustained DISPLAY TEXT (see 6.4.1) Set by product to 0
SEND DTMF command (see 6.4.24) Set by product to 0
RFU, bit = 0
RFU, bit = 0
RFU, bit = 0
RFU, bit = 0
RFU, bit = 0
RFU, bit = 0

Subsequent bytes:

b8 b7 b6 b5 b4 b3 b2 b1
RFU, bit = 0

227
22 APPENDIX D:
Command Type and Next Action Indicator.
This table has been extracted from the 11.14.

Used for Type of used for Next Action


Value Name
Command coding Indicator coding
'00' - -
'01' REFRESH X
'02' MORE TIME X
'03' POLL INTERVAL X
'04' POLLING OFF X
'05' SET UP EVENT LIST X
'10' SET UP CALL X X
'11' SEND SS X X
'12' SEND USSD X X
'13' SEND SHORT MESSAGE X X
'14' SEND DTMF X
'20' PLAY TONE X X
'21' DISPLAY TEXT X X
'22' GET INKEY X X
'23' GET INPUT X X
'24' SELECT ITEM X X
'25' SET UP MENU X X
'26' PROVIDE LOCAL INFORMATION X
'27' TIMER MANAGEMENT X
'28' SET UP IDLE MODEL TEXT X X
'30' PERFORM CARD APDU class "a" only X X
'31' POWER ON CARD class "a" only X X
'32' POWER OFF CARD class "a" only X X
'33' GET READER STATUS class "a" only X X
'34' RUN AT COMMAND class "b" only X
'81' End of the proactive session not applicable X

228
23 APPENDIX E:
Coding of Alpha fields in the SIM for UCS2
The coding can take one of the three following structures. If the ME supports UCS2 coding
of alpha fields in the SIM, the ME shall support all three coding schemes for character sets
containing 128 characters or less; for character sets containing more than 128 characters,
the ME shall at least support the first coding scheme. If the alpha field record contains
GSM default alphabet characters only, then none of these schemes shall be used in that
record. Within a record, only one coding scheme, either GSM default alphabet, or one of
the three described below, shall be used.

➊ If the first octet in the alpha string is '80', then the remaining octets are 16 bit UCS2
characters, with the more significant octet (MSO) of the UCS2 character coded in the
lower numbered octet of the alpha field, and the less significant octet (LSO) of the UCS2
character is coded in the higher numbered alpha field octet, e.g.. octet 2 of the alpha
field contains the more significant octet (MSO) of the first UCS2 character, and octet 3 of
the alpha field contains the less significant octet (LSO) of the first UCS2 character (as
shown below). Unused octets shall be set to 'FF', and if the alpha field is an even
number of octets in length, then the last (unusable) octet shall be set to 'FF'.
Example 1

Octet 1 Octet 2 Octet 3 Octet 4 Octet 5 Octet 6 Octet 7 Octet 8 Octet 9


'80' Ch1 MSO Ch1 LSO Ch3 MSO Ch2 LSO Ch3 MSO Ch3 LSO 'FF' 'FF'

➋ If the first octet of the alpha string is set to '81', then the second octet contains a value
indicating the number of characters in the string, and the third octet contains an 8 bit
number which defines bits 15 to 8 of a 16 bit base pointer, where bit 16 is set to zero,
and bits 7 to 1 are also set to zero. These sixteen bits constitute a base pointer to a "half-
page" in the UCS2 code space, to be used with some or all of the remaining octets in the
string. The fourth and subsequent octets in the string contain codings as follows; if bit 8
of the octet is set to zero, the remaining 7 bits of the octet contain a GSM Default
Alphabet character, whereas if bit 8 of the octet is set to one, then the remaining seven
bits are an offset value added to the 16 bit base pointer defined earlier, and the resultant
16 bit value is a UCS2 code point, and completely defines a UCS2 character.
Example 2

Octet 1 Octet 2 Octet 3 Octet 4 Octet 5 Octet 6 Octet 7 Octet 8 Octet 9


'81' '05' '13' '53' '95' 'A6' 'XX' 'FF' 'FF'

In the above example;


- Octet 2 indicates there are 5 characters in the string
- Octet 3 indicates bits 15 to 8 of the base pointer, and indicates a bit pattern of
0hhh hhhh h000 0000 as the 16 bit base pointer number. Bengali characters for
example start at code position 0980 (0000 1001 1000 0000), which is indicated by
the coding '13' in octet 3 (shown by the italicised digits).

229
- Octet 4 indicates GSM Default Alphabet character ‘53’, e.g.. "S".
- Octet 5 indicates a UCS2 character offset to the base pointer of '15', expressed in
binary as follows 001 0101, which, when added to the base pointer value results in
a sixteen bit value of 0000 1001 1001 0101, e.g.. '0995', which is the Bengali letter
KA.
- Octet 8 contains the value 'FF', but as the string length is 5, this a valid character
in the string, where the bit pattern 111 1111 is added to the base pointer, yielding
a sixteen bit value of 0000 1001 1111 1111 for the UCS2 character (e.g.. '09FF').

➌ If the first octet of the alpha string is set to '82', then the second octet contains a value
indicating the number of characters in the string, and the third and fourth octets contain
a 16 bit number which defines the complete 16 bit base pointer to a "half-page" in the
UCS2 code space, for use with some or all of the remaining octets in the string. The fifth
and subsequent octets in the string contain coding as follows; if bit 8 of the octet is set
to zero, the remaining 7 bits of the octet contain a GSM Default Alphabet character,
whereas if bit 8 of the octet is set to one, the remaining seven bits are an offset value
added to the base pointer defined in octets three and four, and the resultant 16 bit value
is a UCS2 code point, and defines a UCS2 character.
Example 3

Octet 1 Octet 2 Octet 3 Octet 4 Octet 5 Octet 6 Octet 7 Octet 8 Octet 9


'82' '05' '05' '30' '2D' '82' 'D3' '2D' '31'

In the above example


- Octet 2 indicates there are 5 characters in the string
- Octets 3 and 4 contain a sixteen bit base pointer number of '0530', pointing to the
first character of the Armenian character set.
- Octet 5 contains a GSM Default Alphabet character of '2D', which is a dash "-".
- Octet 6 contains a value '82', which indicates it is an offset of '02' added to the
base pointer, resulting in a UCS2 character code of '0532', which represents
Armenian character Capital BEN.
- Octet 7 contains a value 'D3', an offset of '53', which when added to the base
pointer results in a UCS2 code point of '0583', representing Armenian Character
small PIWR.

230
24 APPENDIX F:
Specification of Power Down Control
via RS232
This appendix aims at describing how the power down mode of the product can be
activated and deactivated via the RS232 serial link.
In this document, the term “DTE” refers to the customer device driving the product, which
is referred to as the “DCE”.
The terms referring to the RS232 signals and levels are used according to
recommendations V.24 and V.28. However they are worth at remembering:
DTR is the circuit 108/2, TX is the circuit 103, RX is the circuit 102 and CTS is the circuit 106.
The logical level “HIGH or ON” corresponds to the electrical level of 12 V, whereas the
level “LOW or OFF” corresponds to –12 V.
Basically the activation and deactivation is always initiated from the DTE and is carried out
through the handshaking of DTR and CTS.
The power down mode can be entered only when the DCE is idle, e.g.. when no
connection to the network is in progress.

Into the details :


Whenever the DTE requests the DCE to enter the power down mode, the DTE drops (
ON-to-OFF transition) DTR. From this time on, the DTE must not send any more characters
on the TX line e.g.. even the TX FIFO must be empty.
The DCE acknowledges entry in the power down mode by dropping CTS, which can occur
at maximum 5s after the DTR drop. However during that latency period the DTE is
prohibited from sending any more AT commands.
AT responses can be sent back to the DTE even if the DCE is in power down mode
(actually the DCE exits the power down mode, sends the AT response and enters back the
power down mode). Therefore the DTE can drop DTR just after sending an AT command
and before receiving the AT response.
The DCE is made to exit the power down mode by raising the DTR. DCE is not ready to
receive further AT commands until it raises in turn CTS, which can take up to 2s from the
DTR raise.
Here below is a diagram depicting the handshaking:

DTR 2 6

CTS 4 7

1 8
TX XXXX XXXX
3 5 9
RX XXXX XXXX XXXX

231
Description of the stages:
➊ the DTE sends an AT command
➋ the DTE drops DTR to make the DCE enter the power down mode. Warning: this mode
will not really enter until CTS is dropped (stage 4). The DTE could also have dropped
DTR after receiving the AT response (stage 3).
➌ the DCE sends back the AT response (if any)
➍ the DCE drops CTS and does enter the power down mode.
➎ the DCE sends back an unsolicited response (for instance a RING or +SMTI (incoming
SMS indication))
➏ the DTE wants to reply to that unsolicited response so it causes the DCE to exit the
power down mode by raising its DTR.
➐ in turn the DCE acknowledges the exit of the power down mode by raising CTS.
➑ & ➒ exchange of AT commands/responses.

NOTE 1: The DTE must not send any AT commands from stage 2 on up to stage 7.
NOTE 2: During the latency period (between stages 2 and 4) should the DTE want to abort the power
down mode, it raises DTR and should wait for 150us before assessing CTS. If CTS is still high than the
DCE has aborted the power down mode and is ready to receive AT commands.
The 150us wait should get around the race condition between DTR raise and CTS drop.

232
25 APPENDIX G :
Conditions for command execution
and dependence to SIM

25.1 General commands

AT commands Conditions SIM dependence Intermediate


AT+CGMI None N N
AT+CGMM None N N
AT+CGMR None N N
AT+CGSN None N N
AT+CSCS +WIND: 4 N N
AT+WPCS +WIND: 4 N N
AT+CIMI +WIND: 4 Y N
AT+CCID +WIND: 1 Y N
AT+GCAP None N N
A/ Depends on Depends on prev. N
previous command command N
AT+CPOF +WIND: 3 without SIM, N N
+WIND: 1 with SIM N N
AT+CFUN None N N
AT+CPAS None N N
AT+CMEE None N N
AT+CKPD Depends of the sequence used Y/N N
AT+CCLK +WIND: 4 Y N
AT+CALA None N Y
AT+CRMP None N N
AT+CRSL None N N

25.2 Call Control commands

AT commands Conditions SIM dependence Intermediate


ATD Depends of sequence used Y/N Y
ATH None N N
ATA None N N
AT+CEER +WIND: 4 Y N
AT+VTD None N N
AT+VTS None N N
ATDL None N Y
AT%D None N N
ATS0 None N N
AT+CICB None N N

233
AT+CSNS None N N
AT+VGR None N N
AT+VGT None N N
AT+CMUT None N N
AT+SPEAKER None N N
AT+ECHO None N N
AT+SIDET None N N
AT+VIP None N N
AT+DUI PIN N N
AT+HUI PIN N N
AT+RUI PIN N N

25.3 Network service commands

AT commands Conditions SIM dependence Intermediate


AT+CSQ None N N
AT+COPS +WIND: 4 Y N
AT+CREG None N Y
AT+WOPN None N N
AT+CPOL +WIND: 7 Y Y

25.4 Security commands

AT commands Conditions SIM dependence Intermediate


AT+CPIN +WIND: 1 Y N
AT+CPIN2 after PIN entered Y N
AT+CPINC +WIND: 1 Y N
AT+CLCK +WIND: 4 Y N
AT+CPWD +WIND: 4 Y N

25.5 Phonebook commands

AT commands Conditions SIM dependence Intermediate


AT+CPBS +WIND: 4 Y N
AT+CPBR +WIND: 4 Y Y
AT+CPBF +WIND: 4 Y Y
AT+CPBW +WIND: 4 Y N
AT+CPBP +WIND: 4 Y Y
AT+CPBN +WIND: 4 Y Y
AT+CNUM +WIND: 4 Y N
AT+WAIP None N N
AT+CSVM +WIND: 4 N N

234
25.6 Short Messages commands

AT commands Conditions SIM dependence Intermediate


AT+CSMS +WIND: 4 Y N
AT+CNMA +WIND: 4 Y N
AT+CPMS +WIND: 4 Y N
AT+CMGF +WIND: 4 Y N
AT+CSAS +WIND: 4 Y N
AT+CRES +WIND: 4 Y N
AT+CSDH +WIND: 4 Y N
AT+CNMI +WIND: 4 Y N
AT+CMGR +WIND: 4 Y Y
AT+CMGL +WIND: 4 Y Y
AT+CMGS +WIND: 4 Y N
AT+CMGW +WIND: 4 Y Y
AT+CMSS +WIND: 4 Y N
AT+CSMP +WIND: 4 Y N
AT+CMGD +WIND: 4 Y N
AT+CSCA +WIND: 4 Y N
AT+CSCB +WIND: 4 Y N
AT+WCBM +WIND: 4 Y N
AT+WMSC +WIND: 4 Y Y
AT+WMGO +WIND: 4 Y N
AT+WUSS None N N

25.7 Supplementary Services commands

AT commands Conditions SIM dependence Intermediate


AT+CCFC +WIND: 4 Y N
AT+CLCK +WIND: 4 Y N
AT+CPWD +WIND: 4 Y N
AT+CCWA +WIND: 4 Y N
AT+CLIR +WIND: 4 Y N
AT+CLIP +WIND: 4 Y N
AT+COLP +WIND: 4 Y N
AT+CAOC +WIND: 4 Y Y
AT+CACM +WIND: 4 Y N
AT+CAMM +WIND: 4 Y N
AT+CPUC +WIND: 4 Y N
AT+CHLD +WIND: 4 Y N
AT+CLCC None N N

235
AT+CSSN None N N
AT+CUSD None N N
AT+CCUG +WIND: 4 Y Y

25.8 Data commands

AT commands Conditions SIM dependence Intermediate


AT+CBST None N N
AT+FCLASS None N N
AT+CR None N N
AT+CRC None N N
AT+ILRR +WIND: 4 N N
AT+CRLP None N N
AT+DOPT None N N
AT%C None N N
AT+DS None N N
AT+DR None N N
\N None N N

25.9 Fax commands

AT commands Conditions SIM dependence Intermediate


AT+FTM None N N
AT+FRM None N N
AT+FTH None N N
AT+FRH None N N
AT+FTS None N N
AT+FRS None N N

25.10 Class 2 commands

AT commands Conditions SIM dependence Intermediate


AT+FDT None N N
AT+FDR None N N
AT+FET None N N
AT+FPTS None N N
AT+FK None N N
AT+FBOR None N N
AT+FBUF None N N
AT+FCQ None N N
AT+FCR None N N
AT+FDIS None N N

236
AT+FDCC None N N
AT+FLID None N N
AT+FPHCTO None N N

25.11 V24-V25 commands

AT commands Conditions SIM dependence Intermediate


AT+IPR None N N
AT+ICF None N N
AT+IFC None N N
AT&C None N N
AT&D None N N
AT&S None N N
ATO +WIND: 4 N N
ATQ None N N
ATV None N N
ATZ None N N
AT&W None N N
AT&T None N N
ATE None N N
AT&F None N N
AT&V None N N
ATI None N N
AT+WMUX None N N

25.12 Specific AT commands

AT commands Conditions SIM dependence Intermediate


AT+CCED None N N
AT+WIND None N N
AT+ADC None N N
AT+CMER +WIND: 4 N N
AT+WLPR +WIND: 1 N N
AT+WLPW +WIND: 1 N N
AT+WIOR None N N
AT+WIOW None N N
AT+WIOM None N N
AT+WAC None N N
AT+WTONE None N N
AT+WDTMF None N N
AT+WDWL None N N

237
AT+WVR None N N
AT+WDR None N N
AT+WHWV None N N
AT+WDOP None N N
AT+WSVG None N N
AT+WSTR None N N
AT+WSCAN None N N
AT+WRIM None N N
AT+W32K None N N
AT+WCDM None N N
AT+WSSW None N N
AT+WCCS +WIND: 4 N N
AT+WLCK None (PIN for auto CNL) N (Y for auto CNL) N
AT+CPHS +WIND: 4 Y N
AT+WBCM None N N
AT+WFM None N N
AT+WCFM None N N
AT+WMIR None N N
AT+WCDP None N N
AT+WMBN PIN Y N
AT+WOPEN None N N
AT+WRST None N N
AT+WSST None N N
AT+WLOC PIN Code Y N
AT+WBR None N N
AT+WBW None N N
AT+WBM None N N

25.13 SIM Toolkit commands

AT commands Conditions SIM dependence Intermediate


AT+STSF None N N
AT+STIN +WIND: 4 Y N
AT+STGI +WIND: 4 Y N
AT+STGR +WIND: 4 Y N

238
WAVECOM S.A. - 12, boulevard Garibaldi - 92442 Issy-les-Moulineaux Cedex - France - Tel: +33 (0)1 46 29 08 00 - Fax: +33 (0)1 46 29 08 08
WAVECOM, Inc. - 4810 Eastgate Mall - Second floor - San Diego, CA 92121 - USA - Tel: +1 858 362 0101 - Fax: +1 858 558 5485
WAVECOM Asia Pacific Ltd - 5/F Shui On Centre - 6/8 Harbour Road - Hong Kong, PRC - Tel: +852 2824 0254 - Fax: +852 2824 0255

www.wavecom.com

You might also like