Professional Documents
Culture Documents
VHF FM TRANSCEIVER
iV8000
This device complies with Part 15 of the FCC rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FOREWORD IMPORTANT
Thank you for purchasing this Icom product. The IC-V8000 READ ALL INSTRUCTIONS carefully and completely
VHF FM TRANSCEIVER is designed and built with Icom’s supe- before using the transceiver.
rior technology and craftsmanship. With proper care, this prod-
uct should provide you with years of trouble-free operation. SAVE THIS INSTRUCTION MANUAL— This in-
struction manual contains important operating instructions for
We want to take a couple of moments of your time to thank the IC-V8000.
you for making your IC-V8000 your radio of choice, and hope
you agree with Icom’s philosophy of “technology first.” Many
hours of research and development went into the design of
your IC-V8000. EXPLICIT DEFINITIONS
WORD DEFINITION
D FEATURES Personal injury, fire hazard or electric shock
R WARNING!
may occur.
❍ 75 W* of high transmit output power
CAUTION Equipment damage may occur.
(except Taiwan version)
Recommended for optimum use. No risk of
❍ Front mounted speaker for clear audio NOTE
personal injury, fire or electric shock.
readability
❍ Tone squelch, DTCS squelch standard
❍ Dual color (amber & green) LCD backlight
❍ Remote control microphone available
(optional for some versions) Icom, Icom Inc. and the logo are registered trademarks of Icom
Incorporated (Japan) in the United States, the United Kingdom, Ger-
❍ Optional DTMF decoder many, France, Spain, Russia and/or other countries.
i
CAUTIONS
RWARNING RF EXPOSURE! This device emits NEVER place the transceiver where normal operation of the
Radio Frequency (RF) energy. Extreme caution should be ob- vehicle may be hindered or where it could cause bodily injury.
served when operating this device. If you have any questions re-
garding RF exposure and safety standards please refer to the
NEVER let objects impede the operation of the cooling fan on
the rear panel.
Federal Communications Commission Office of Engineering and
Technology’s report on Evaluating Compliance with FCC Guide- DO NOT push the PTT when not actually desiring to transmit.
lines for Human Radio frequency Electromagnetic Fields (OET
Bulletin 65)
DO NOT allow children to play with any radio equipment con-
taining a transmitter.
RWARNING! NEVER connect the transceiver to an AC During mobile operation, DO NOT operate the transceiver
outlet. This may pose a fire hazard or result in an electric shock.
without running the vehicle’s engine. When the transceiver’s
RWARNING! NEVER operate the transceiver while dri- power is ON and your vehicle’s engine is OFF, the vehicle’s bat-
ving a vehicle. Safe driving requires your full attention—anything tery will soon become exhausted.
less may result in an accident.
BE CAREFUL! The transceiver will become hot when op-
NEVER connect the transceiver to a power source of more erating it continuously for long periods.
than 16 V DC. This will ruin the transceiver.
AVOID using or placing the transceiver in direct sunlight or in
NEVER connect the transceiver to a power source using re- areas with temperatures below –10°C (+14˚F) or above +60°C
verse polarity. This will ruin the transceiver. (+140˚F).
NEVER cut the DC power cable between the DC plug and AVOID the use of chemical agents such as benzine or alcohol
fuse holder. If an incorrect connection is made after cutting, the when cleaning, as they can damage the transceiver’s surfaces.
transceiver may be damaged.
USE Icom microphones only (supplied or optional). Other man-
NEVER expose the transceiver to rain, snow or any liquids. ufacturer’s microphones have different pin assignments and may
The transceiver may be damaged. damage the transceiver if attached.
NEVER operate or touch the transceiver with wet hands. This
may result in an electric shock or ruin the transceiver.
ii
SUPPLIED ACCESSORIES TABLE OF CONTENTS
FOREWORD ........................................................................................... i
IMPORTANT ............................................................................................ i
q w e EXPLICIT DEFINITIONS ......................................................................... i
CAUTIONS ............................................................................................. ii
SUPPLIED ACCESSORIES .................................................................. iii
r TABLE OF CONTENTS ......................................................................... iii
QUICK REFERENCE GUIDE ............................................................ I–VI
t y ■ Installation ....................................................................................... I
■ Your first contact ........................................................................... IV
■ Repeater operation ........................................................................ V
■ Programming memory .................................................................. VI
1 PANEL DESCRIPTION ................................................................. 1–8
■ Front panel ..................................................................................... 1
■ Function display ............................................................................. 3
■ Rear panel ..................................................................................... 5
q DC power cable (3 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ■ Microphone (HM-133V) .................................................................. 6
w Mobile mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . 1 ■ Microphone keypad ........................................................................ 7
e Microphone (HM-133V)* . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 SETTING A FREQUENCY .......................................................... 9–12
■ Preparation .................................................................................... 9
r Fuse (20 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
■ Using the tuning dial ...................................................................... 9
t Mounting screws, nuts and washers . . . . . . . . . . . . 1 set ■ Using the keypad ......................................................................... 10
y Microphone hanger† . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ■ Using the [Y]/[Z] keys ................................................................. 10
*HM-118N HAND MICROPHONE or HM-118TN/TAN DTMF MICROPHONE ■ Tuning step selection ................................................................... 11
supplied versions are also available. ■ Lock functions .............................................................................. 12
†
Depending on version. 3 BASIC OPERATION ................................................................. 13–16
■ Receiving ..................................................................................... 13
■ Monitor function ........................................................................... 13
■ Audio mute function ..................................................................... 14
■ Squelch attenuator ....................................................................... 14
■ Transmitting ................................................................................. 15
■ Selecting output power ................................................................ 15
■ One-touch PTT function ............................................................... 16
iii
1
2
4 REPEATER OPERATION ......................................................... 17–23 ■ Transmitting a DTMF code .......................................................... 46
■ Accessing a repeater ................................................................... 17 ■ DTMF speed ................................................................................ 47 3
■ Subaudible tones ......................................................................... 19 10 POCKET BEEP AND TONE SQUELCH ................................... 48–51
■ Offset frequency .......................................................................... 21 ■ Pocket beep operation ................................................................. 48 4
■ Repeater lockout .......................................................................... 21 ■ Tone/DTCS squelch operation ..................................................... 50
■ Reverse duplex mode .................................................................. 22 ■ Tone scan ..................................................................................... 51
5
■ Auto repeater ............................................................................... 23 11 PAGER/CODE SQUELCH ........................................................ 52–57 6
5 MEMORY OPERATION ............................................................ 24–34 ■ Pager function .............................................................................. 52
■ General description ...................................................................... 24 ■ Code programming ...................................................................... 52 7
■ Memory channel selection ........................................................... 24 ■ Pager operation ........................................................................... 55
■ Programming a memory channel ................................................. 25 ■ Code squelch ............................................................................... 57 8
■ Transferring memory contents ..................................................... 27 12 OTHER FUNCTIONS ................................................................ 58–70
■ Memory clearing .......................................................................... 29 ■ Set mode ...................................................................................... 58 9
■ Channel names programming ...................................................... 30 ■ Initial set mode ............................................................................. 62
■ Memory bank selection ................................................................ 32 ■ Weather channel operation .......................................................... 65 10
■ Memory bank setting .................................................................... 33 ■ Microphone keys .......................................................................... 67
■ Transferring bank contents .......................................................... 34 ■ Partial reset .................................................................................. 68
11
6 CALL CHANNEL OPERATION ................................................ 35–36 ■ All reset ........................................................................................ 68 12
■ Call channel selection .................................................................. 35 ■ Data cloning ................................................................................. 69
■ Call channel transferring .............................................................. 35 13 MAINTENANCE ........................................................................ 71–73 13
■ Programming a call channel ........................................................ 36 ■ Troubleshooting ........................................................................... 71
7 SCAN OPERATION .................................................................. 37–42 ■ Fuse replacement ........................................................................ 72 14
■ Scan types ................................................................................... 37 ■ Optional unit installation ............................................................... 73
■ Scan start/stop ............................................................................. 38 14 SPECIFICATIONS AND OPTIONS ................................................. 74 15
■ Scan edges programming ............................................................ 39 15 MODE ARRANGEMENT ........................................................... 75–76
■ Skip channel setting ..................................................................... 41
■ Scan resume condition ................................................................ 42
8 PRIORITY WATCH .................................................................... 43–44
■ Priority watch types ...................................................................... 43
■ Priority watch operation ............................................................... 44
9 DTMF MEMORY ENCODER ..................................................... 45–47
■ Programming a DTMF code ......................................................... 45
iv
QUICK REFERENCE GUIDE
■ Installation
D Location D Using the mounting bracket
Select a location which can support the weight of the trans- ➀ Drill 4 holes where the mounting bracket is to be installed.
ceiver and does not interfere with driving in any way. We rec- • Approx. 5.5–6 mm (1⁄4″) when using nuts; approx. 2–3 mm (1⁄8″)
ommend the locations shown in the diagram below. when using self-tapping screws.
➁ Insert the supplied screws, nuts and washers through the
NEVER place the transceiver where normal operation of the mounting bracket and tighten.
vehicle may be hindered or where it could cause bodily injury. ➂ Adjust the angle for the clearest view of the function dis-
play.
NEVER place the transceiver where air bag deployment may
be obstructed.
DO NOT place the transceiver where hot or cold air blows di- Nut
rectly onto it. Spring washer
Flat washer
AVOID placing the transceiver in direct sunlight. Mounting
bracket
I
QUICK REFERENCE GUIDE
IC-V8000
IC-V8000
DC power
⊕ red − black supply 13.8 V
+ red
_ black
Fuses
20 A to an
AC − ⊕
outlet
12 V
battery Fuses
12 V Supplied
− black 20 A
DC power cable
⊕ red
NOTE: Crimp Solder
Use terminals for the
cable connections.
II
QUICK REFERENCE GUIDE
;y
(10 mm ≈ 3⁄8 in)
NOTE: There are many publications covering proper an-
tennas and their installation. Check with your local dealer
for more information and recommendations.
D Connecting a microphone
Connect a microphone to the eight-pin modular socket on the
front panel of the transceiver.
to antenna
*HM-133V; A different microphone may be
supplied with some versions of the IC-V8000.
III
QUICK REFERENCE GUIDE
Push
Set both [VOL] and [SQL] controls to
9–10 o’clock positions.
Push
Although you have purchased a brand new transceiver, some
settings may be changed from the factory defaults because
of the QC process. Resetting the CPU is necessary to start
from factory default. Push
Push
■ Repeater operation
1. Setting duplex Using the HM-133V
Push [LOW(DUP)] for 1 sec. once or twice to select minus du- Plus or minus duplex selection and the repeater tone setting
plex or plus duplex. can be made easily via HM-133V.
• The USA and CSA versions have an auto repeater function, there- Push [DUP– 7(TONE)] for minus duplex; [DUP+ 8(TSQLS)]
fore, setting duplex is not required. for plus duplex selection, push [FUNC] then [DUP– 7(TONE)]
to turn the repeater tone ON.
Push
[LOW(DUP)]
Push
2. Repeater tone
Push [TONE(T-SCAN)] several times until “ ” appears, if the
repeater requires a subaudible to be accessed.
Push , then
[TONE(T-SCAN)]
V
QUICK REFERENCE GUIDE
■ Programming memory
channels Using the HM-133V
q In VFO mode, set the desired operating frequency, includ-
The IC-V8000 has a total of 200 memory channels (including ing offset direction, tone settings, etc.
6 scan edges and 1 call channel) for storing often used oper- w Push [FUNC] then [CLR A(MW)].
ating frequency, repeater settings, etc. • “M” indicator and memory channel number blink.
1. Setting a frequency
In VFO mode, set the desired operating frequency with re- Push ,
peater, tone and tuning steps, etc.
then
2. Selecting a memory channel
Momentarily push [MW(S.MW)], then rotate the tuning dial to
e Push [Y]/[Z] to select the desired memory channel.
select the desired memory channel.
• “M” indicator and memory channel number blink. r Push [FUNC] then push [CLR A(MW)] for 1 sec. to pro-
gram.
• 3 beeps sound
• Memory channel number automatically increases when continu-
ing to push [CLR A(MW)] after programming.
[MW(S.MW)]
VI
1 PANEL DESCRIPTION
■ Front panel
Function display (p. 3) !3 !2 !1 !0
q PWR TONE
T-SCAN
LOW
DUP
w M/CALL
PRIO
V/MHz
SCAN
MONI
ANM
SET MW
LOCK S.MW
e BANK
OPT
r t y u i o Speaker
2
1 PANEL DESCRIPTION
■ Function display
!5 !4 !3 !2 !1
q
!0
r t y u i o
4
1 PANEL DESCRIPTION
■ Rear panel
e r
w
q SPEAKER JACK [SP] e COOLING FAN
Accepts an 8 Ω speaker. Rotates while transmitting.
• Audio output power is more than 2.0 W. Also rotates while receiving depending on the setting in set
mode and transceiver’s temperature. (p. 61)
w POWER RECEPTACLE [DC13.8V]
Accepts 13.8 V DC ±15% with the supplied DC power r ANTENNA CONNECTOR [ANT]
cable. Connects a 50 Ω antenna with a PL-259 connector and a
50 Ω coaxial cable.
☞ NOTE: DO NOT use a cigarette lighter socket as a
power source when operating in a vehicle. The plug
may cause voltage drops and ignition noise may be su-
perimposed onto transmit or receive audio.
5
PANEL DESCRIPTION 1
■ Microphone keypad
Starts and stops priority watch. (p. 44) Turns the one-touch PTT function ON and
OFF. (p. 16)
Selects high output power. (p. 15) Turns the DTCS squelch ON. (p. 50)
After pushing :
Transmits the appropriate
Selects mid. output power. (p. 15) Turns the DTCS pocket beep function ON. DTMF code. (pgs. 20, 46)
(p. 49) When the DTMF memory en-
Selects low output power (p. 15) Turns the DTMF memory encoder function coder is activated, push [0] to
ON. (p. 45) [9] to transmit the appropriate
Selects minus duplex operation. (p. 18) Turns the subaudible tone encoder ON. DTMF memory contents .
(p. 18) (p. 46)
Selects plus duplex operation. (p. 18) Turns the CTCSS pocket beep function
ON. (p. 49)
Selects simplex operation. (p. 18) Turns the tone squelch function ON.
(p. 50)
No primary function. Sends a 1750 Hz tone signal while pushing
and holding. (p. 20)
7
PANEL DESCRIPTION 1
8
2 SETTING A FREQUENCY
9
SETTING A FREQUENCY 2
Push
Push
Push
Push
10
2 SETTING A FREQUENCY
Tuning steps are the minimum frequency change increments z Push [VFO/LOCK] to select VFO mode, if
when you rotate the tuning dial or push [Y]/[Z] on the micro- VFO/LOCK necessary.
phone. The following tuning steps are available. x Push [SET B(D-OFF)] to enter set mode.
• 5 kHz • 10 kHz • 12.5 kHz • 15 kHz c Push [SET B(D-OFF)] or [ENT C(T-OFF)]
• 20 kHz • 25 kHz • 30 kHz • 50 kHz several times until “TS” appears.
v Push [Y] or [Z] to select the desired tuning
☞NOTE: For convenience, select a tuning step that matches
step.
the frequency intervals of repeaters in your area.
b Push [CLR A(MW)] to exit set mode.
q Push [V/MHz(SCAN)] to se-
lect VFO mode, if neces-
sary.
w Push [SET(LOCK)] to enter
[SET(LOCK)] Tuning dial set mode.
[MW(S.MW)] e Push [SET(LOCK)] or
[MW(S.MW)] several times
until “TS” appears as shown
at left.
r Rotate the tuning dial to se-
15 kHz tuning step lect the desired tuning step.
t Push [TONE(T-SCAN)] to
exit set mode.
11
SETTING A FREQUENCY 2
■ Lock functions
To prevent accidental channel changes and unnecessary D Microphone keypad lock 2
function access, use the lock function. The transceiver has 2 This function locks the microphone keypad.
different lock functions.
➥ Push [FUNC] then [SQLZ D(16KEY-L)] to
D Frequency lock 16KEY-L switch the microphone keypad lock function
This function locks the tuning dial and switches electronically ON and OFF.
and can be used together with the microphone lock function. • [PTT], [VFO/LOCK], [MR/CALL], [BANK/OPTION],
[Y], [Z], [F-1], [F-2], [DTMF-S] and [FUNC] on the
➥ Push [SET(LOCK)] for
microphone can be used.
1 sec. to turn the lock func- • All switches on the transceiver can be used.
tion ON and OFF. • The keypad lock function is released when the
• [PTT], [MONI(ANM)], [VOL] power is turned OFF then ON again.
Push [SET(LOCK)] for 1 sec. and [SQL] can be used while
the channel lock function is in
use. Also, TONE-1, TONE-2,
DTMF tones or DTMF mem-
ory contents can be transmit-
ted from the microphone.
Appears
12
3 BASIC OPERATION
✔CONVENIENT!
The squelch level can also be adjusted with
SQLY [SQLY D(MUTE)] and [SQLZ #(16KEY-L)].
D
SQLZ
#
13
BASIC OPERATION 3
Noise squelch
Squelch
threshold
Appears
Squelch is Squelch
open. attenuator
Shallow Deep
14
3 BASIC OPERATION
15
BASIC OPERATION 3
16
4 REPEATER OPERATION
■ Accessing a repeater
q Set the receive frequency (repeater output frequency). r Push and hold [PTT] to transmit.
(pgs. 9, 10) • The displayed frequency automatically changes to the transmit
w Push [LOW(DUP)] for 1 sec., one or two times, to select frequency (repeater input frequency).
minus duplex or plus duplex. • If “OFF” appears, confirm that the offset frequency (p. 21) is set
• “–” or “+” appears to indicate the transmit frequency for minus correctly.
shift or plus shift, respectively. t Release [PTT] to receive.
• When the auto repeater function is turned ON (available for the
USA and CSA versions), steps w and e are not necessary.
(p. 23)
[TONE(T-SAN)] Appears
17
REPEATER OPERATION 4
z Set the receive frequency (repeater output fre- m Push [SIMP 9(TSQL)] to return to simplex opera-
DUP– quency). (pgs. 9, 10) SIMP tion.
7 9
x Push [DUP– 7(TONE)] to select minus duplex; • “+” or “–” indicator disappears.
push [DUP+ 8(TSQLS)] to select plus duplex. , To turn OFF the subaudible tone encoder, push
DUP+ [FUNC] then [ENT C(T-OFF)].
8 Push
4
Push
Push ,
then .
18
4 REPEATER OPERATION
Push
[SET(LOCK)]
r Rotate the tuning dial to select and set the desired sub- v Push [Y] or [Z] to select and set the desired
audible frequency. subaudible tone frequency.
• Push and hold [Y]/[Z] to change the above tones
t Push [TONE(T-SCAN)] to exit set mode.
continuously.
☞NOTE: The subaudible tone encoder frequency can be set b Push [CLR A(MW)] to exit set mode.
in a memory/call channel temporarily. However, the set fre-
• Subaudible tone frequency list (unit: Hz)
quency is cleared once another memory channel or VFO
67.0 79.7 94.8 110.9 131.8 156.7 171.3 186.2 203.5 229.1
mode is selected. To store the tone frequency permanently,
69.3 82.5 97.4 114.8 136.5 159.8 173.8 189.9 206.5 233.6
overwrite the channel information. 71.9 85.4 100.0 118.8 141.3 162.2 177.3 192.8 210.7 241.8
74.4 88.5 103.5 123.0 146.2 165.5 179.9 196.6 218.1 250.3
77.0 91.5 107.2 127.3 151.4 167.9 183.5 199.5 225.7 254.1
19
REPEATER OPERATION 4
Push ,
Push ,
then push desired keys. then or .
20
4 REPEATER OPERATION
[SET(LOCK)]
e Rotate the tuning dial to set the desired offset frequency. While pushing [SET(LOCK)],
turn power ON.
r Push [TONE(T-SCAN)] to exit set mode.
e Push [SET(LOCK)] or [MW(S.MW)] several times until the
z Push [SET B(D-OFF)] to enter set mode.
SET “RLO” display appears as shown below.
x Push [SET B(D-OFF)] or [ENT C(T-OFF)] until “±”
B r Rotate the tuning dial to turn the repeater lockout function
and offset frequency appear.
to “RP,” “BU” or OFF.
Push
Repeater lockout function is Repeater lockout function is
turned OFF. turned ON.
• “RP”: Transmit is inhibited when a signal with un-matched sub-
c Push [Y] or [Z] to set the desired offset. audible tone is received.
• Direct frequency entry from the keypad is not possi- • “BU”: Transmit is inhibited when a signal is received.
ble. t Push [PWR] to exit initial set mode.
v Push [CLR A(MW)] to exit set mode.
21
REPEATER OPERATION 4
22
4 REPEATER OPERATION
23
MEMORY OPERATION 5
■ General description
The transceiver has 207 memory channels including 6 scan D Using the [Y]/[Z] keys
edge memory channels (3 pairs), and 1 call channel. Each of z Push [MR/CALL] to select memory mode.
these channels can be individually programmed with operat- MR/CALL x Push [Y] or [Z] to select and set the desired
ing frequency (pgs. 9, 10), duplex direction (p. 19) and offset memory channel. 4
(p. 21), subaudible tone encoder or tone squelch and its tone • Pushing [Y]/[Z] for 1 sec. activates a scan.
frequency (pgs. 19, 48–50) and skip information* (p. 41). Y/Z • If scan is activated, push [Y]/[Z] again or push
5
In addition, a total of 10 memory banks, A to J, are available [CLR A(MW)] to stop it.
for usage by group, etc.
*except for scan edge memory channels.
D Using the keypad
z Push [MR/CALL] to select memory mode.
MR/CALL x Push [ENT C(T-OFF)] to activate the keypad
■ Memory channel selection for numeral input.
c Push 3 appropriate digit keys to input a chan-
D Using the tuning dial Y/Z
nel number.
q Push [M/CALL(PRIO)] • When inputting non-programmed channel num-
once or twice to select bers, the previous memory channel appears.
memory mode. • Push only 1 appropriate digit key, [MONI 1(ANM)],
• “M” indicator appears [SCAN 2(T-SCAN)] or [PRIO 3(PTT-M)], then push
Push [M/CALL(PRIO)] to select w Rotate the tuning dial to M(TONE-1)] or [SQLZ #(16KEY-L)] to select scan
[M
memory mode. edge channels. “MM” and “#” can be used for “A”
select the desired mem-
and “b” respectively.
ory channel.
• Programmed memory
channels only can be se-
lected.
Appears
24
5 MEMORY OPERATION
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel) via the front panel.
V/MHz MW
Push SCAN Rotate for setting frequency, etc. Push S.MW momentarily.
Rotate Push MW
S.MW for 1 sec. and continue to push ➠
“
“Beep
“ Beep
“ Beep
“
25
MEMORY OPERATION 5
z Set the desired frequency in VFO mode. v Push [FUNC] then [CLR A(MW)] for 1 sec. to program.
➥ Push [VFO/LOCK] to select VFO mode. ➥ 3 beeps may sound and the VFO contents (including
➥ Set the frequency using the keypad. the subaudible tone frequency, etc.) are programmed. 5
➥ Set other data (e.g. offset frequency, duplex direction, sub- ➥ Memory channel number increases when continuing to
audible tone encoder ON/OFF and its frequency) , if neces- push [CLR A(MW)] after programming.
sary.
x Push [FUNC] then [CLR A(MW)] momentarily.
c Select the memory channel to be programmed.
➥ Push [Y] or [Z] to select the memory channel (direct nu-
meral input cannot be used).
[EXAMPLE]: Programming 145.870 MHz into memory channel 20 (blank channel) via the microphone.
Push Push Push then momentarily.
HM-133V operation:
Push to select memory mode. Select memory channel. Push then push for 1 sec.
27
MEMORY OPERATION 5
HM-133V operation:
Select the memory channel, push then push . Push then push for 1 sec.
28
5 MEMORY OPERATION
■ Memory clearing
Contents of programmed memories can be cleared (blanked), r Push [MW(S.MW)] momentarily, then push [MW(S.MW)]
if desired. again for 1 sec.
☞ This operation must be performed within 1.5 sec.
q Push [V/MHz(SCAN)] to select VFO mode. • 3 beeps sound, then the frequency is cleared.
w Push [MW(S.MW)] momentarily. • “M” indicator blinks continuously.
• “M” indicator and the memory channel number blink. • When clearing the call channel, the current VFO conditions are
e Rotate the tuning dial to select the memory channel to be re-programmed into the call channel automatically.
cleared. t Push any switch, except [MW(S.MW)], to return to VFO
• Memory channels not yet programmed are blank. mode.
MW MW
“
“Beep MW
Push S.MW momentarily, then push S.MW again for 1 sec. Push any switch, except S.MW .
“ Beep
“ Beep
“
29
MEMORY OPERATION 5
30
5 MEMORY OPERATION
z Select the memory/call channel to be assigned memory b Push [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cur-
names. sor to left or right, respectively.
➥ Push [MR/CALL] to select memory mode, then select n Repeat steps v and b until the desired channel names
the desired memory channel via [Y]/[Z] or keypad. are displayed.
• Scan edge channels can also be selected. m Push [CLR A(MW)] to program the name and exit the chan-
➥ Push [MR/CALL] for 1 sec. to select the call channel. nel name programming condition.
x Push [FUNC], then [MONI 1(ANM)] momentarily. , Push [FUNC], then push [MONI 1(ANM)] to return to fre-
c Push [SET B(D-OFF)]. quency indication if desired.
• Frequency readouts disappear.
v Push [Y]/[Z] to select the desired character.
• The selected character blinks.
31
MEMORY OPERATION 5
32
5 MEMORY OPERATION
33
MEMORY OPERATION 5
[EXAMPLE]: Programming 145.120 MHz into the call channel via the microphone.
Push to select VFO mode. Set the frequency. Push , then .
Push until large “C” appears. Push , then push for 1 sec. ➠“ “ “
Beep
Beep
“ Beep
“
36
7 SCAN OPERATION
■ Scan types
Scanning searches for signals automatically and makes it There are 3 scan types and 4 resume conditions to suit your
easier to locate new stations for contact or listening purposes. operating needs.
FULL SCAN (p. 38) Repeatedly scans all frequen- PROGRAMMED SCAN Repeatedly scans between
cies over the entire band. (p. 38) two user-programmed fre-
Band Band Used as the simplest scan quencies. Used for checking
edge edge without any preliminary set- for frequencies within a speci-
Band Scan edges Band
Scan
tings necessary. edge edge fied range such as repeater
output frequencies, etc. 3
Scan
pairs of scan edges are avail-
Jump able.
Jump
MEMORY SCAN (p. 38) Repeatedly scans memory SCAN RESUME 4 resume conditions are avail-
channels except those set as CONDITION (p. 42) able: 3 timer scans and pause
skip channels. Used for often- scan. When receiving a sig-
SKIP
called channels and for by- Receiving nal, pause scan pauses until
M1 M2 M3 a signal
passing normally busy Pause
the signal disappears; timer
M0 M4 channels such as repeater scan scans pause for 5, 10 or
M 199 M6 M5
SKIP frequencies. 2 sec. 15 sec.
Timer
scan
Pausing
☞ NOTE: A tone scan function is available to search for subaudible tones (e.g. when you want to find a subaudible tone fre-
quency necessary to open a repeater). See p. 51 for details.
37
SCAN OPERATION 7
■ Scan start/stop
D Preparation
Scan resume condition (p. 42); program the scan edges z Push [VFO/LOCK] to select VFO mode for
SCAN full/programmed scan; push [MR/CALL] to select
(pgs. 39, 40); program 2 or more memory channels (pgs. 25, 2
26); set skip settings, if desired (p. 41). memory mode for memory scan.
• Push [BANK/OPTION] to select a bank for bank
SET scan.
D Operation B
q Select VFO mode for full/programmed scan with x Set the squelch to the point where noise is just
[V/MHz(SCAN)]; or memory mode for memory scan with muted.
[M/CALL(PRIO)]. c Push [SCAN 2(T-SCAN)] to start the scan. 7
• Push [Y] or [Z] for 1 sec. also starts the scan.
• Select the desired bank with [BANK(OPT)] for bank scan.
w Set the squelch to the point where noise is just muted. v Push [SET B(D-OFF)] to switch full and pro-
e Push [V/MHz(SCAN)] for 1 sec. to start the scan. grammed scan (P1, P2 and P3).
• To change the scanning direction, rotate the tuning dial. b To stop the scan push [SCAN 2(T-SCAN)] or
• The memory channel readout blinks the scan type as follows: [CLR A(MW)].
r Push [SET(LOCK)] to switch full and programmed scan
(P1, P2 and P3).
t To stop the scan, push [V/MHz(SCAN)].
Push MW
S.MW for 1 sec. and continue to push ➠
“
“Beep “Beep
“ Beep
“ Beep
“
39
SCAN OPERATION 7
[EXAMPLE]: Programming 145.300 MHz and 145.800 MHz into scan edges 1A and 1b, respectively.
Push Push Push then momentarily.
The memory skip function speeds up scanning by checking z Select a memory channel.
only those memory channels not set as skip channels. Set SET ➥ Select memory mode by pushing [MR/CALL].
B
skip channels as follows. ➥ Push [Y] or [Z] to select the desired channel
to be a skip channel.
The display shows that x Push [SET B(D-OFF)] to enter set mode.
memory channel 1 is set c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several
as a skip channel. times until “CHS” appears as shown at left.
v Push [Y] or [Z] to set or cancel the skip setting.
• See item r at left for skip indicator details.
b Push [CLR A(MW)] to exit set mode.
q Select a memory channel:
➥ Push [M/CALL(PRIO)] to select memory mode.
➥ Rotate the tuning dial to select the desired channel to ☞ NOTES:
be a skip channel. Even though scan edge channels cannot be set as skip
w Push [SET(LOCK)] to enter set mode. channels, they ARE skipped during memory scan.
e Push [SET(LOCK)] or [MW(S.MW)] several times until SET mode cannot be accessed when memory names are
“CHS” appears as shown above. displayed. To set the scan resume condition, return to fre-
r Rotate the tuning dial to turn the skip function ON or OFF quency indication by pushing [MONI(ANM)] on the front
for the selected channel. panel for 1 sec., or push [FUNC] then [MONI 1(ANM)] (HM-
• “~” appears : The channel is skipped during scan. 133V) to cancel the channel name indication, then set as
(CHS-ON)
described on this page.
• “~” disappears : The channel is scanned during scan.
(CHS-OFF)
t Push [TONE(T-SCAN)] to exit set mode.
41
SCAN OPERATION 7
The scan resume condition can be selected as timer or pause z Push [SET B(D-OFF)] to enter set mode.
scan. The selected resume condition is also used for priority SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] several
B
watch. (p. 44) times until “SCT” or “SCP” appears as shown at
left.
The display shows that the c Push [Y] or [Z] to select the scan resume condi-
scan will resume 15 sec. tion.
after it stops. • See item e at left for scan resume condition details. 7
v Push [CLR A(MW)] to exit set mode.
☞ NOTE:
q Push [SET(LOCK)] to enter set mode. Set mode cannot be accessed when memory names are
w Push [SET(LOCK)] or [MW(S.MW)] several times until displayed. To set the scan resume condition, return to fre-
“SCT” or “SCP” appears as shown above. quency indication by pushing [MONI(ANM)] on the front
• When “d” is displayed in place of the 100 MHz digit, cancel the panel for 1 sec., or push [FUNC] then [MONI 1(ANM)] (HM-
DTMF memory encoder in advance. (p. 46) 133V) to cancel the channel name indication, then set as
e Rotate the tuning dial to set the desired timer: described on this page.
• “SCT-15” : Scan pauses 15 sec. while receiving a signal.
• “SCT-10” : Scan pauses 10 sec. while receiving a signal.
• “SCT-5” : Scan pauses 5 sec. while receiving a signal.
• “SCP-2” : Scan pauses until the signal disappears and then
resumes 2 sec. later.
r Push [TONE(T-SCAN)] to exit set mode.
42
8 PRIORITY WATCH
43
PRIORITY WATCH 8
44
9 DTMF MEMORY ENCODER
Push Push
45
DTMF MEMORY ENCODER 9
46
9 DTMF MEMORY ENCODER
47
POCKET BEEP AND TONE SQUELCH 10
■ Pocket beep operation
This function uses subaudible tones for calling and can be y Push [TONE(T-SCAN)] several times until “ ” or “ ”
used as a “common pager” to inform you that someone has are displayed to turn ON the pocket beep with tone
called while you were away from the transceiver. squelch or DTCS squelch, respectively.
48
10 POCKET BEEP AND TONE SQUELCH
49
POCKET BEEP AND TONE SQUELCH 10
50
10 POCKET BEEP AND TONE SQUELCH
■ Tone scan
By monitoring a signal that is being operated with pocket r When the CTCSS tone frequency or 3-digit DTCS code is
beep, tone or DTCS squelch function, you can determine the matched, the squelch opens and the tone frequency is
tone frequency or DTCS code necessary to open a squelch. temporarily programmed into the selected condition such
as memory or call channel.
q Set the channel to be checked for a tone frequency or • The tone scan pauses when a CTCSS tone frequency or 3-digit
code. DTCS code is detected.
w Push [TONE(T-SCAN)] several times to select the tone • The decoded CTCSS tone frequency or 3-digit DTCS code is
condition or type to be scanned. used for the tone encoder or tone encoder/decoder depending
• One of “ ,” “ ” or “ ” appears on the selected tone condition or type in step w.
e Push [TONE(T-SCAN)] for 1 sec. to start the tone scan. - No indication : Cannot be used for operation.
• To change the scanning direction, rotate the tuning dial. -“ ” : CTCSS tone encoder
-“ ” : CTCSS tone encoder/decoder
-“ ” : DTCS tone encoder/decoder
t Push [V/MHz(SCAN)] to stop the scan.
52
11 PAGER/CODE SQUELCH
D Code programming
An ID code MUST be programmed into code channel C0. Up y Push [MW(S.MW)] to select 2nd digit, then rotate the tuning
to 6 transmit codes are programmable into code channels, C1 dial to set the desired code.
to C6, if required. • 2nd digit blinks (1st digit stop blinking).
• Repeat this step for 3rd digit programming.
q Push [BANK(OPT)] for 1 sec.
• Pager mode is selected.
• 100 MHz digit shows “P.”
53
PAGER/CODE SQUELCH 11
54
11 PAGER/CODE SQUELCH
■ Pager operation
Optional UT-108 required
D Calling a specific station
z Program the desired code channel in ad-
q Program the desired code channel in advance (p. 53). BANK/OPTION vance (p. 54).
w Set the operating frequency.
• Set the [VOL] and [SQL] to the desired level as in normal opera- x Set the operating frequency.
tion. c Push [BANK/OPTION] for 1 sec. to select
e Push [BANK(OPT)] for 1 sec. to select pager mode. pager mode.
• 100 MHz digit shows “P.” • 100 MHz digit shows “P.”
v Select the desired transmit code channel:
➥ Push [SET(LOCK)].
➥ Push [Y]/[Z].
➥ Push [CLR A(MW)] to return to the previ-
ous condition.
r Select the desired transmit code channel: b Push [PTT] to transmit the pager code.
➥ Push [SET(LOCK)]. n Wait for an answer back.
➥ Rotate the tuning dial to select the code channel. • When the transceiver receives an answer back
➥ Push [TONE(T-SCAN)] to return to the previous condition. code, the function display shows the other
t Push [PTT] to transmit the pager code. member’s ID or group code.
• Transmits your ID and the selected transmit codes automatically. m After confirming a connection, push
y Wait for an answer back. [BANK/OPTION] for 1 sec. to select the
• When the transceiver receives an answer back code, the func- code squelch operation, or repeat the pre-
tion display shows the other member’s ID or group code. vious key operation again to select non-se-
u After confirming a connection, push [BANK(OPT)] for lective calling system.
1 sec. to select the code squelch operation, or repeat the , Communicate with the other party as nor-
previous key operation again to select non-selective calling mal: push [PTT] to transmit; release to re-
system. ceive.
i Communicate with the other party as normal: push [PTT]
to transmit; release to receive.
55
PAGER/CODE SQUELCH 11
56
11 PAGER/CODE SQUELCH
57
OTHER FUNCTIONS 12
■ Set mode
• Set mode operation
z Push [SET B(D-OFF)] to enter set mode.
q Push [SET(LOCK)] to enter the set mode. SET x Push [SET B(D-OFF)] or [ENT C(T-OFF)] to select
w Push [SET(LOCK)] or [MW(S.MW)] to select the desired B
the desired item.
item.
c Push [Y] or [Z] to select the condition or value.
e Rotate the tuning dial to select the condition or value.
v Push [CLR A(MW)] to exit set mode.
r Push [TONE(T-SCAN)] to exit set mode.
• Set mode items
• Display dimmer • Display color • Repeater tone • Tone squelch tone • DTCS code&polarity
• Wide/Nar. setting* • Channel skip setting† • Transmit permission • Scan resume • Tuning step‡
58
12 OTHER FUNCTIONS
59
OTHER FUNCTIONS 12
D Reverse mode
Sets the reverse function ON and OFF (default).
D Transmit permission
Turns transmission permission ON and OFF. This function
can be set for each memory, call channel and VFO, indepen- 12
dently.
Reverse function OFF (default) Reverse function ON
D Tuning step
Selects tuning step from 5 (default), 10, 12.5, 15, 20, 25, 30
and 50 kHz for the tuning dial or [Y]/[Z] operation. Transmission is permitted. Transmission is inhibited.
(default)
60
12 OTHER FUNCTIONS
Scans the memory channel. Does not scan the memory ☞NOTE: When the transceiver internal temperature exceeds
(does not skip; default) channel (skips). +45˚C (approx.; +113˚F),the fan continuously rotates at mid-
dle or high speed, regardless of this setting.
D Wide/Narrow setting
Sets both the transmission and reception passband width
from wide and narrow.
When narrow is set, the transmission deviation and reception
Auto setting (default) Continuously ON with high
passband width become half of the wide setting (approx.).
speed setting.
This setting can be set for each memory, call and VFO inde-
pendently.
This item appears in some USA versions only. D Weather alert function U.S.A. versions only
Turns weather alert function ON and OFF.
61
OTHER FUNCTIONS 12
The initial set mode is accessed at power ON and al- D Entering initial set mode
lows you to set seldom-changed settings. In this way, q While pushing [SET(LOCK)], push [PWR] for 1 sec. to
you can “customize” transceiver operations to suit your enter initial set mode.
preference and operating style. w Push [SET(LOCK)] or [MW(S.MW)] to select the desired
item.
e Rotate the tuning dial to select the condition or value.
• Initial set mode items r Push [PWR] to exit initial set mode.
• Key-touch beep
• Squelch attenuator • Time-out timer
SET
12
: Push LOCK (front panel); or (microphone)
MW
: Push S.MW (front panel); or (microphone)
62
12 OTHER FUNCTIONS
63
OTHER FUNCTIONS 12
D DTMF speed
D Repeater lockout The rate at which DTMF memories send individual DTMF
characters can be set to accommodate operating needs.
Selects lockout type from repeater, busy and OFF.
•1 : 100 msec. interval; 5.0 cps speed (default) 12
• OF : No lockout is activated. (default)
•2 : 200 msec. interval; 2.5 cps speed
• RP : The repeater lockout is turned ON.
•3 : 300 msec. interval; 1.6 cps speed
• BU : The busy lockout is turned ON.
•5 : 500 msec. interval; 1.0 cps speed
64
12 OTHER FUNCTIONS
D Squelch attenuator
Turns the squelch attenuator function ON and OFF.
• ON : The squelch attenuator activates when [SQL]
control is set between 12 o’clock and fully
clockwise position. (default)
• OF : The squelch attenuator does not function.
65
OTHER FUNCTIONS 12
66
12 OTHER FUNCTIONS
■ Microphone keys
The supplied HM-133V’s (optional for some versions) [F-1] D [UP]/[DN] keys on a microphones
and [F-2] keys memorize the transceiver conditions. (other than HM-133V) AT POWER ON
The [UP]/[DN] keys of the standard or an optional microphone
(other than the HM-133V) can be assigned functions like the The following functions are assigned to the [UP]/[DN] keys on
function keys on the transceiver’s front panel. the other microphones (HM-118N/TAN, etc.) when first apply-
ing power.
D [F-1]/[F-2] keys on HM-133V [UP] : channel up; push and hold to start scan, push again
The following conditions can be memorized into [F-1] and to stop scan.
[F-2] keys, independently. [DN] : channel down; push and hold to start scan, push
• Operating frequency again to stop scan.
• Repeater setting (offset direction and frequency, tone
ON/OFF and frequency)
➥ Assigning a function
• Tone/DTCS squelch (ON/OFF, frequency/code and polarity) q Turn the power OFF.
• Transmit output power selection w While pushing the desired switch on the transceiver and
• Set mode settings one of either [UP]/[DN] keys on the microphone, turn the
• Initial set mode settings (except display type item) power ON.
• The function is programmed into the key.
➥ Programming the condition
[F-1]/[F-2] Set the desired contents of each condition, ➥ Clearing an assignment
then push [F-1]/[F-2] for 1 sec. q Turn the power OFF.
• 3 beeps sound. w While pushing the desired [UP] or [DN] key on the micro-
phone, turn the power ON.
➥ Re-calling the condition
Push [F-1]/[F-2] momentarily.
67
OTHER FUNCTIONS 12
IMPORTANT!:
Resetting the transceiver CLEARS all memory information
and initializes all values in the transceiver.
While pushing [V/MHz(SCAN)],
turn power ON. ➥ While pushing [SET(LOCK)] and [MW(S.MW)], turn the
power ON to reset the CPU.
12
68
12 OTHER FUNCTIONS
D Cloning error
☞ NOTE: DO NOT push any key on the sub-transceiver dur-
ing cloning. This will cause a cloning error.
When the display at left ap-
pears, a cloning error has oc-
curred.
71
MAINTENANCE 13
■ Fuse replacement 13
If the fuse blows or the transceiver stops functioning, find the
source of the problem if possible, and replace the damaged 20 A
fuse with a new, rated one (FGB 20 A) as shown at right. fuse
72
13 MAINTENANCE
w Detach the front panel from the main unit. t Return the front panel and the allen-socket bolts to their
original position.
73
SPECIFICATIONS AND OPTIONS 14
■ Specifications RECEIVER
• Receive system : Double-conversion superheterodyne
GENERAL • Intermediate frequencies : 1st: 21.7 MHz, 2nd: 450 kHz
• Frequency coverage : (unit: MHz) • Sensitivity (at 12 dB SINAD) : 0.15 µV typical
USA Tx: 144–148/Rx: 136–174* • Squelch sensitivity (threshold) : 0.08 µV typical
Asia, CSA Tx: 144–148/Rx: 136–174* • Selectivity (typical) : 75 dB (wide)/60 dB (narrow)†
(Central South America) • Spurious and image rejection : 75 dB typical
Australia Tx/Rx: 144–148 • AF output power (at 13.8 V DC) : More than 2.0 W at 10% distortion with
Taiwan, Korea Tx/Rx: 144–146 an 8 Ω load
*Guaranteed: 144–148 MHz range only. • Ext. speaker connector : 3-conductor 3.5 (d) mm (1⁄8″)/8 Ω
• Type of emission : FM †
Some versions only.
• Number of memory channels : 207 (incl. 6 scan edges and 1 call)
All stated specifications are subject to change without notice or obligation.
• Frequency resolution : 5, 10, 12.5, 15, 20, 25, 30, 50 kHz
• Operating temperature range : –10°C to +60°C; +14˚F to +140˚F
• Frequency stability
• Power supply requirement
: ±10 ppm (–10°C to +60°C)
: 13.8 V DC ±15% ■ Options
• Current drain (at 13.8 V DC: approx.):
UT-108 DTMF DECODER UNIT
Transmit at 75 W 15 A
Receive standby 0.3 A typical
HM-95/HM-118TAN/TN DTMF MICROPHONES
max. audio 1.0 A HM-118N HAND MICROPHONE
• Antenna connector : SO-239 (50 Ω) HM-133V REMOTE-CONTROL MICROPHONE
• Dimensions (proj. not included) : 150(W) × 50(H) × 150(D) mm SP-10 EXTERNAL SPEAKER 13
529⁄32(W)×2(H)×529⁄32(D) in OPC-440/OPC-647 MIC EXTENSION CABLES
14
• Weight (approx.) : 1.1 kg; 2 lb 7 oz OPC-441 SPEAKER EXTENSION CABLE
OPC-1132/OPC-347 DC POWER CABLES
TRANSMITTER OPC-589 ADAPTER CABLE
• Modulation system : Variable reactance frequency mod.
CS-V8000 CLONING SOFTWARE + OPC-478 CLONING CABLE
• Output power : 75/25/10/5 W* (approx.)
OPC-474 CLONING CABLE
*24/10/5 W only for the Taiwan version.
• Max. frequency deviation : ±5.0 kHz (wide)/±2.5 kHz (narrow)†
• Spurious emissions : Less than –60 dB
• Microphone connector : 8-pin modular (600 Ω)
74
15 MODE ARRANGEMENT
TONE
T-SCAN
When the DTMF
memory encoder is
activated.
M/CALL
PRIO
MEMORY MODE (p. 24) CALL CHANNEL (p. 35) See p. 45 for details.
MONI
ANM CLONE MODE
for 1 sec. BANK
OPT
WEATHER CHANNEL (p. 65)*2
MONI
ANM
CHANNEL NAME BANK CHANNEL (p. 32) *1Appears when accessing from memory mode only.
INDICATION (p. 30) *2Available for USA versions only.
*3Appears in some version only.
*4Appears when accessing from VFO mode only.
75
MODE ARRANGEMENT 15
Beep tone
Display dimmer (p. 59) Tuning step (p. 60)*4 on/off (p. 63)
Time-out
timer (p. 63)
Display color (p. 59) Scan resume timer (p. 60)
Auto repeater*2
(p. 63)
Auto power-
Repeater tone (p. 59) Transmit permission (p. 60)
off (p. 64)
MW MW
SET
LOCK S.MW
SET
LOCK
Repeater S.MW
lockout
Tone squelch tone (p. 59) Skip setting*1 (p. 61) (p. 64)
Squelch
delay (p. 64)
DTCS code and polarity (p. 59) Wide/Nar. selection*3 (p. 61) DTMF speed
(p. 64)
15
Display type
Offset frequency (p. 60) Cooling fan setting (p. 61) (p. 65)
Squelch
attenuator
Reverse mode (p. 60) Weather alert*2 (p. 61) (p. 65)
76
A-6115D-1EX
Printed in Japan
© 2001 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan