Fold and unfold the diagonals. 4 fold and unfold the angle bisectors. Turn the paper over. 8 fold and unfold through both layers. Unfold. Fold the flap at the back down as far as it will go. Turn the model over. 40 fold and unfold. 43 Valley-fold the center flap to the right I and repeat step 42 on the left side. 45 Squeeze the sides together and swing the bottom flap over to the left.
Fold and unfold the diagonals. 4 fold and unfold the angle bisectors. Turn the paper over. 8 fold and unfold through both layers. Unfold. Fold the flap at the back down as far as it will go. Turn the model over. 40 fold and unfold. 43 Valley-fold the center flap to the right I and repeat step 42 on the left side. 45 Squeeze the sides together and swing the bottom flap over to the left.
Fold and unfold the diagonals. 4 fold and unfold the angle bisectors. Turn the paper over. 8 fold and unfold through both layers. Unfold. Fold the flap at the back down as far as it will go. Turn the model over. 40 fold and unfold. 43 Valley-fold the center flap to the right I and repeat step 42 on the left side. 45 Squeeze the sides together and swing the bottom flap over to the left.
Spined Ant ea eas 7
Use foil-backed paper
od
1 Begin with the white side up. 2) Fold and unfold the angle 3. Fold and untold
Fold and unfold the alagonals talsectors. Turn the paper over.
4 Fold and untold Fold and unfold 6 Fold ane untold
e¢
7 Mountain-told pening: Fold and unfold the angle 9 Mountain-fold behing
bisectors through both layers
Unfold to step 710) Fold and unfold the angle 11 Enlarged view. Make the two 12. Collapse on excistin
al 9 P a
bisectors through both layers. vertical mountainefolds and then creases, Next step shows
Unfold start pushing in the area within this step seen from the side
the triangles (see next step).
13 stop 12 ceen trom the side, 14. Petatfold 5. Fold and unfold
partially collapsed Repeat behind through all layers.
ys
fay
- 1/4
Ss
16 Fold the flap at the back 17 swivet-fold. Repeat an the 18 Like this. Closed-sink the
down as far as it will go. right, thus being able to lower triangle upward.
Rotate the model squash flat (see next step),RW Valley-fold the center flap 44 Fold and unfold. 45) open sink
to the right, and repeat step
42 on the left side.my Y
AG etail of sink, Repeat 47 Fold and unfold the 4S Fold and unfold the
steps 44-45 on the angel bisector. angle bisector
left side
AD Revetse-fald 50 spread-squash 51 Reverse-fold
in and out.
52. Reverse-fold two edges. 53> cutaway view. Reverse-fold Repeat steps 51-53 on the
Then unfold each edge three times. left flap. This is easier if
The valley fold is on the the right flap is unfolded
crease made in step 52 during the process.55> enlarged view of the head 56 Lin the fap upward 57 Plest-fold. The divisions,
Reverse-fald the antennae without pressing flat using the edge behind,
to each side as far as they are approximate
will go
58 swire-fold the sides 59 Fold down 60 Reverse-fold
\Valley-fold the top comer. Repeat on the left
side.
61 valiey-fold 62 open up the eyes 63 Rabbitearthe antennae
and squash flat 0 that they point straight
out toward youCollapsing on the creases made
64 Lit the flap at the back 65 the back-body is not shown. 66 jin step 21, put the two edges
and fold the head to the Squash the thick edge flat inside the nearest packets
front, Next view from the The resulting point will point
right side slightly downward. Repeat behind.
;
67 Like this. Next view 68 open up the edges below 69 View fram behind
fiom top of back-bedy and fold comer a over to Fold the edge inside
the right. The body becomes
3dimensional
bd
70 Detail of head. 71 Squashetold 72. Petatfold.
Push in where indicated, Press the
jaws together and fold the resulting
edge to the left at the back-side,
Next view from behind the jawseof
73 Collapse to make a point 74. the head is now 3-D. 75 Pinch between the head and
partly on existing creases Pinch and form mmid-body, and between the
Edge a and b will point the antennae mid-body and back-body
straight backward
76 Pinch points a, b and c. 77 Pinch the two front pairs of legs 78 The finished Spined Ant.
Paint c should be slightly with mountain folds, and the third
raised pair with valley folds. Then cue
and form the legs to make feet ete.
Side view.