Professional Documents
Culture Documents
SPECIFICATIONS
TABLE OF CONTENTS
1. SERVICING NOTES ................................................ 3 7-4. Printed Wiring Board — BD83S Board — .................... 25
7-5. Schematic Diagram — BD83S Board — ....................... 26
2. GENERAL ................................................................... 4 7-6. Printed Wiring Boards
— MAIN Board, REG Board — ..................................... 27
3. DISASSEMBLY 7-7. Schematic Diagram
3-1. Disassembly Flow ........................................................... 6 — MAIN Board (1/3), REG Board — ............................ 28
3-2. Side Panel (R), Side Panel (L) ......................................... 7 7-8. Schematic Diagram — MAIN Board (2/3) — ............... 29
3-3. Top Panel Section ............................................................ 7 7-9. Schematic Diagram — MAIN Board (3/3) — ............... 30
3-4. Mechanical Deck ............................................................. 8 7-10. Printed Wiring Board — AMP Board — ....................... 31
3-5. Belt (MAIN), Belt (R/F) .................................................. 8 7-11. Schematic Diagram — AMP Board — .......................... 32
3-6. Front Panel Section ......................................................... 9 7-12. Printed Wiring Board — PANEL Board — ................... 33
3-7. PANEL Board .................................................................. 9 7-13. Schematic Diagram — PANEL Board — ...................... 34
3-8. JACK Board ..................................................................... 10 7-14. Printed Wiring Boards
3-9. MAIN Board, REG Board ............................................... 10 — POWER Board, JACK Board — ................................ 35
3-10. CD Mechanism Deck Section (BU-K6BD83S2) ............ 11 7-15. Schematic Diagram
3-11. Optical Pick-up (KSM-213DCP), BD83S Board ............ 12 — POWER Board, JACK Board — ................................ 36
3-12. Belt (DLM3A) ................................................................. 13
3-13. DC Fan, Chassis (MAIN MOLD) ................................... 13 8. EXPLODED VIEWS
3-14. POWER Board, AMP Board ........................................... 14 8-1. Overall Section ................................................................ 45
8-2. Front Panel Section ......................................................... 46
4. TEST MODE ............................................................... 15 8-3. Chassis Section ................................................................ 47
8-4. Top Panel Section ............................................................ 48
5. MECHANICAL ADJUSTMENTS ......................... 16 8-5. CD Mechanism Deck Section (BU-K6BD83S2-WOD) . 49
7. DIAGRAMS
7-1. Block Diagram — BD/DRIVER Section — .................. 22
7-2. Block Diagram — TUNER Section — .......................... 23
7-3. Block Diagram — MAIN Section — ............................. 24
2
HCD-GB3
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead- Laser component in this product is capable of emitting radiation
free mark (LF) indicating the solder contains no lead. exceeding the limit for Class 1.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size) NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
: LEAD FREE MARK The laser diode in the optical pick-up block may suffer electrostatic
Unleaded solder has the following characteristics. break-down because of the potential difference generated by the
• Unleaded solder melts at a temperature about 40 °C higher charged electrostatic load, etc. on clothing and the human body.
than ordinary solder. During repair, pay attention to electrostatic break-down and also
Ordinary soldering irons can be used but the iron tip has to be use the procedure in the printed matter which is included in the
applied to the solder joint for a slightly longer time. repair parts.
Soldering irons using a temperature regulator should be set to The flexible board is easily damaged and should be handled with
about 350 °C. care.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful! NOTES ON LASER DIODE EMISSION CHECK
• Strong viscosity The laser beam on this model is concentrated so as to be focused on
Unleaded solder is more viscou-s (sticky, less prone to flow) the disc reflective surface by the objective lens in the optical pick-
than ordinary solder so use caution not to let solder bridges up block. Therefore, when checking the laser diode emission,
occur such as on IC pins, etc. observe from more than 30 cm away from the objective lens.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
LASER DIODE AND FOCUS SEARCH OPERATION
also be added to ordinary solder.
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveforms is output three times.
CAUTION
3
HCD-GB3
SECTION 2 This section is extracted
GENERAL from instruction manual.
"ASIC /PERATIONS
s 4HE MAXIMUM NUMBER OF 4HE SYSTEM OFFERS THE FOLLOWING DISPLAY MODES
!DJUSTING THE SOUND n FOLDERS IS INCLUDING THE ROOT FOLDER
n -0 lLES IS $ISPLAY MODE 7HEN THE SYSTEM IS OFF
n -0 lLES AND FOLDERS THAT CAN BE CONTAINED ON A SINGLE DISC IS $EMONSTRATION 4HE CLOCK DISPLAY IS REPLACED BY
4O ADJUST THE VOLUME
n FOLDER LEVELS THE TREE STRUCTURE OF lLES IS EIGHT
LIGHTING AND mASHING OF THE DISPLAY
0RESS 6/,5-% n ON THE REMOTE OR TURN THE WINDOW
s #OMPATIBILITY WITH ALL -0 ENCODINGWRITING SOFTWARE RECORDING
6/,5-% CONTROL ON THE UNIT ȵ DEVICE AND RECORDING MEDIA CANNOT BE GUARANTEED )NCOMPATIBLE #LOCK 4HE CLOCK IS DISPLAYED
-0 DISCS MAY PRODUCE NOISE OR INTERRUPTED AUDIO OR MAY NOT PLAY
4O ADD A SOUND EFFECT AT ALL 0OWER 3AVING 4HE DISPLAY IS TURNED OFF TO CONSERVE
4O 0RESS -ODE POWER 4HE TIMER AND CLOCK CONTINUE
.OTES ON PLAYING MULTISESSION DISCS
TO OPERATE
'ENERATE A MORE DYNAMIC $3'8 Ȼ ON THE UNIT s )F THE DISC BEGINS WITH A #$
$! OR -0 SESSION IT IS RECOGNIZED
XT AS A #$
$! OR -0 DISC AND PLAYBACK CONTINUES UNTIL ANOTHER
4HE 34!.$"9 INDICATOR Ȫ LIGHTS UP WHEN THE SYSTEM IS OFF
SOUND $YNAMIC 3OUND
XB 'ENERATOR 8
TRA
SESSION IS ENCOUNTERED
7HEN THE SYSTEM IS IN 0OWER 3AVING -ODE THE FOLLOWING FUNCTIONS
s ! DISC WITH A MIXED #$ FORMAT IS RECOGNIZED AS A #$
$! AUDIO ARE UNAVAILABLE
X 3ET THE SOUND EFFECT %1 ȯ DISC n SETTING THE CLOCK
n CHANGING THE !- TUNING INTERVAL
n CHANGING THE #$ POWER MANAGE FUNCTION
RM