Professional Documents
Culture Documents
As the rocker arm is moved by the eccentric, the diaphragm is pulled down against
the spring force. This movement causes a partial vacuum in the pump chamber. Now
the delivery valve remains closed and the suction valve opens. This admits fuel into
the pump chamber. At the maximum position of the eccentric, the diaphragm is
flexed to the maximum extent. After this, further rotation of the eccentric will release
the rocker arm. Now the rocker arm will simply follow the eccentric by the action of
the return spring. The diaphragm spring will now push the diaphragm upwards and
force the fuel to flow out, opening the delivery valve, into the delivery tube. Now the
suction valve remains closed.
1
Fuel Pump and Carburetor
2
Fuel Pump and Carburetor
2.2 CARBURETOR
Functions of a carburetor:
a. It maintains a small quantity of petrol in the float chamber at constant head
(height) to ensure uninterrupted supply for vaporization.
b. It vaporizes (atomizes) petrol, i.e. it converts liquid petrol to vapor form for
convenient mixing with the air.
c. It does carburetion i.e. prepares a homogeneous mixture of air and vapor
petrol
d. It delivers correct air-fuel mixture to the engine through the manifold under
varying conditions of load and speed of the engine.
A simple carburetor consists of a float chamber, float, needle valve, jet nozzle,
mixing chamber, venturi, throttle and a choke. The float is a hollow and light weight
part made of thin metal sheet. The float chamber maintains the fuel at a constant
level which is necessary for normal operation of a carburetor. The float chamber is
vented through a hole to communicate with the atmosphere. When the fuel level
sinks, the float goes down, opens the needle valve and admits fuel into the chamber.
And when the fuel level reaches its normal level, the float goes up, closes the needle
valve and stops inflow of the fuel. A normal level is reached when the fuel in the
chamber is 1-2 mm below the edge of the nozzle. This level ensures easy suction of
fuel from the nozzle and prevents leakage when the carburetor is inoperative.
The jet tube - with a calibrated hole of definite diameter meters out the amount of
fuel to be supplied. The pulverizer which takes the form of a pin tube communicates
with float chamber through the jet. Mixing chamber is straight or bent tube one of
whose ends is connected to the engine inlet pipe and the other to the air cleaner.
The fuel is mixed with air precisely in this chamber. Venturi mounted in the mixing
chamber at the end of the nozzle increases the velocity of the air stream in the
mixing chamber and there by provides a more intensive atomization of fuel. Throttle
changes the cross section presented to the combustible mixture. The throttle is
controlled by the driver from the cab. The degree to which the throttle is opened
determines the amount of mixture passed and accordingly changes the power of the
engine. A simple carburetor is shown in the figure below.
3
Fuel Pump and Carburetor
The figure above shows the different types of mixing chamber. The most commonly
used mixing chamber is the down draught type mixing chamber.
4
Fuel Pump and Carburetor
Limitations of simple
carburetor and methods to
5
Fuel Pump and Carburetor
overcome them
A simple carburetor works well when the engine runs at a preset speed and
the stipulated load. It is because the nozzle and the venturi dimensions are set for a
particular speed and the load. But working of carburetor at a single condition is
impracticable.
The construction of a simple carburetor cannot fulfill the fuel demand at different
loads, changing speeds and varying weather conditions. Due to these limitations, a
simple carburetor cannot be used in actual practice. To make it suitable for
commercial applications, its limitations are to be overcome. For that various
arrangements are incorporated in its construction. These arrangements and
difficulties (limitations) overcome by them are given as below.
6
Fuel Pump and Carburetor
Choke is the name given to a butterfly valve (or choke valve) which normally remains
in the dotted position when the choke is not used, but turns about its pivot when the
choke is operated. In doing so, it chokes the air passage and allows a very small
quantity of air to flow past itself. A small quantity of fuel issues out of the jet due to
the vacuum produced in the cylinder on cranking. The proportion of this small
7
Fuel Pump and Carburetor
quantity of petrol forms a rich to very rich mixture with a very small quantity of air.
Hence the mixture ignites without trouble and the engine starts.
The choke valve is fitted on the top of the air horn with its pivot located eccentrically
(fig.2a) or in the centre (fig.2b). The eccentrically mounted choke opens easily and
immediately due to a twisting moment produced by unequal forces on AB and BC
sides of the choke. If a centrally mounted choke is used, a strangler valve is also
employed on it (Fig. 3). This helps in avoiding the mixture from becoming over-rich
by allowing air to pass through it when the engine is started.
8
Fuel Pump and Carburetor
Idling Passage: During idling of an engine, the suction developed inside the
engine is not sufficient to draw fuel from the main nozzle. Since engine remains
operative and throttle valve remains slightly opened in this condition, therefore fuel is
supplied through an idling hole, which is provided above the air screw hole.
Compensator Jet: When engine operates at low speeds at the throttle is wide
open, the suction produced within engine is not very strong. Hence petrol is lifted
from compensator nozzle 1 and also from the main nozzle 2. The main nozzle is
being fed from open well 3 as shown in figure above. The action of compensator
nozzle holds down the supply of petrol and so the open well is emptied.
9
Fuel Pump and Carburetor
Compound Jet. In this case a compensatory jet is also provided for supply of
petrol in addition to a main jet (nozzle) the provision also involves an open well which
is vented to atmosphere. Its use is required when the engine is not running. In that
case the level of petrol in it remains the same as that in the float chamber, and petrol
does not flow via the compensatory jet. The arrangement is known as compound jet
because it involves use of two jets: main jet and the compensatory (or submerged)
jet.
While operating at high speeds, the suction is greatly increased as indicated by
several arrows in Figure. Now supply of petrol is maintained mainly through the
main nozzle, however the auxiliary nozzle still gives the same measured quantity of
petrol because of the suction of compensatory
nozzle.
The quantity of petrol supplied by the two jets is a function of throttle opening. At
lesser throttle opening the supply is mainly through the compensating jet which
diminishes with increase in the throttle opening. The supply from main jet is just
opposite to it. It increases with an increase in the throttle opening. Since flow of air
increases at higher speeds but the flow of petrol from compensatory jet remains
constant, therefore a weaker mixture is the outcome for vehicle’s requirement. A
compound jet arrangement has been incorporated in Zenith carburetor.
10
Fuel Pump and Carburetor
Quite often we need sudden acceleration of the vehicle for which the throttle is
suddenly opened. This causes a large quantity of air to rush into the carburetor at
once. However, the petrol through the main jet does not flow immediately. Its effect
is a weak mixture due to lagging petrol supply which causes ‘spluttering’ and so the
acceleration to the vehicle is hampered.
11
Fuel Pump and Carburetor
In normal state (released pedal position as shown in figure, the piston sucks the
petrol from the float chamber, and delivers the same when the accelerator pedal is
pressed. The stiffness of the spring is such that it gets compressed only when a
sudden force is applied on the accelerator pedal. Otherwise, it does not influence
normal working of the accelerator or pedal.
12
Fuel Pump and Carburetor
13
Fuel Pump and Carburetor
Figure above shows approaching full throttle: Fuel is drawn from the main discharge system and fed
into the venturi.
14
Fuel Pump and Carburetor
Figure shows the acceleration module: The extra fuel required is supplied by the accelerator pump,
which also delivers into the venturi
A sliding piston controls the area of the venture throat, and the position of the
piston is determined by the degree of throttle opening. If the throttle is almost
closed, as when the engine is idling, the flow of air through the venture drops. The
weight of the piston and its spring causes the piston to fall, leaving only a small gap
for the passage of air.
When the throttle is opened by depressing the accelerator pedal, the swifter
passage of air through the venture increases the partial vacuum above the piston.
This causes the piston to rise, and further increases the flow of air into the engine.
15
Fuel Pump and Carburetor
The flow of fuel is controlled by a tapered needle attached to the piston and passing
into the fuel jet. As the piston rises, the needle rises too, allowing more petrol to be
drawn from the jet. The position of the jet and shape of the needle ensure the
correct proportion of petrol and air.
Since the air pressure in the venture remains reasonably constant at any
given engine speed, there is no need to provide a separate fuel circuit for idling, as in
the fixed-jet carburetor. The fuel is fed into the air stream at the point of maximum
velocity, ensuring efficient atomization (breaking up into droplets) of the fuel.
The idling –mixture strength can be altered by an adjusting nut, which controls the jet
position, and the idling speed is controlled by a throttle-stop screw.
16
Fuel Pump and Carburetor
17
Fuel Pump and Carburetor
18
Fuel Pump and Carburetor
Operational details of SU
Constant depression carburetor
Also rigidly attached to the piston assembly is the tapered needle N which therefore, as the piston
moves, simultaneously varies the annular orifice between itself and the jet. The jet sleeve J can be
raised or lowered for overriding the setting, for idling or starting. This is done by means of a cam and
link connection to the throttle and cold start controls. Petrol is delivered through a nylon tube to the
lower end of the jet sleeve, from the float chamber – which can be bolted on to either side of the
carburetor body, to suit the particular installation.
19
Fuel Pump and Carburetor
Exercise 2
b) Electromagnetic Pump
3. What are the requirements of air fuel mixture and their properties?
20