Professional Documents
Culture Documents
westhq es dce, no requiere clockrate en pc netadmin en terminal: Router>ena Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)#hostname WB2 WB2(config)#enable secret class WB2(config)#line console 0 WB2(config-line)#password cisco WB2(config-line)#login WB2(config-line)#line vty 0 4 WB2(config-line)#password cisco WB2(config-line)#login WB2(config-line)#exit WB2(config)#banner motd iAuthorized access only!# WB2(config)#interface fa0/0 WB2(config-if)#ip address 172.16.100.129 255.255.255.192 WB2(config-if)#no shutdown
WB2(config-if)#interface s0/0/0 WB2(config-if)#ip address 172.16.100.242 255.255.255.252 WB2(config-if)#nmo shutdown ^ % Invalid input detected at '^' marker.
WB2(config-if)#no shutdown
WB2(config-if)#interface Loo %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/0, changed state to up WB2(config-if)#interface Lo0
En wbranch1:
Paso 4
Paso 5 Wbranch1 WB1#conf Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z. WB1(config)#router ospf 1 WB1(config-router)#network 172.16.100.0 0.0.0.127 area 0 WB1(config-router)#network 172.16.100.224 0.0.0.15 area 0 WB1(config-router)#network 172.16.100.244 0.0.0.3 area 0 WB1(config-router)#?
area
log-adjacency-changes Log changes in adjacency state network no Enable routing on an IP network Negate a command or set its defaults Suppress routing updates on an interface Redistribute information from another routing protocol router-id for this OSPF process
WB1(config-router)#passive-interface fa0/0 Wbracnh2 WB2>ena Password: Password: WB2#conf Configuring from terminal, memory, or network [terminal]? t Enter configuration commands, one per line. End with CNTL/Z. WB2(config)#router ospf 1 WB2(config-router)#network 172.16.100.128 0.0.0.63 area 0 WB2(config-router)#network 172.16.100.224 0.0.0.15 area 0 WB2(config-router)#network 172.16.100. 01:55:03: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.0.1 on FastEthernet0/1 from LOADING to FULL, Loading Done WB2(config-router)#network 172.16.100.240 0.0.0.3 area 0 WB2(config-router)#passive-interface fa0/0 Westhq
WHQ(config)#router ospf 1 WHQ(config-router)#network 172.16.100.244 0.0.0.3 area 0 WHQ(config-router)#network 172.16.100.240 0.0.0.3 area 0 WHQ(config-router)#default-information originate
Paso 5 b Wbranch1 WB1(config)#interface fa0/1 WB1(config-if)#ip ospf priority 100 WB1(config-if)#ip ospf hello-interval 20 Wbranch2 WHQ(config-router)#end WHQ#exit WB2(config)#interface f0/1 WB2(config-if)#ip ospf priority 50 WB2(config-if)#ip ospf hello-interval 20 Paso 5c