You are on page 1of 6

OCXO 91-30

P.O. BOX 3389 CHARLOTTESVILLE, VIRGINIA 22903 PHONE: (804) 295-3101 FAX: (804) 977-1849

CRYSTAL OSCILLATOR SPECIFICATION


This specification defines the operating characteristics of an ovenized crystal oscillator. Long term stability is assured through use of premium components.

REV. A B

DESCRIPTION OF REVISION

REQ. BY TST

DWN. BY TST TST TST

DATE 10-12-93 02-03-94 06-23-94

Added temperatures to 2.8., Reordered sequency in 9., Added spaces to 9.5. Added 1.6.b., In 2.2.a. 48 was 24, In 2.5. Added after 40 minutes on, 2.10. was 6x10-9, 2.1. was 2x10-8, 7. was -30 dBi and - 43 dBm Added note to 2.1. and 3. In 9.8. added spaces before and after the =. In 9.8.c. added 5 spaces. In 5.3. spec. was < 0.002 VDC. 2.11. was total gamma and added 250 Hz to 1 kHz range.

ADB TST

TST

TST

09-21-94

D E

TST TST

DLR DLR

11-14-94 03-22-95

ISOTEMP RESEARCH INC. CODE ID. CHARLOTTESVILLE, VA. USA 31785

PART NO. OCXO 91-30

PAGE OF TOTAL DWG. NO. REV. 1 5 114-597 E

OCXO 91-30
1. OUTPUT 1.1. Frequency 1.2. Waveform 1.3. Level 1.4. Load 1.5. Harmonics 1.6. Spurious a. Into 50 s b. Into 180 pF, 620 pF, 2000 pF, .47 uH, 1.8 uH, and 5.6 uH 2. FREQUENCY STABILITY 2.1. Ambient

5.000 MHz Sine wave > +7 dBm 50 10% < -25 dBc < -80 dBc < -60 dBc

from -30C to +70C (referenced to +25C) NOTE: The AMBIENT specification is set tighter internally by ISOTEMP to eliminate correlation differences and guarantee that the customer requirement is met with a Cpk of > 1.5. a. With Cpk > 1.5 < 2.2x10-8 b. Internal to ISOTEMP < 9x10-9 2.2. Aging after storage of up to 90 days a. Daily after 48 hours < 2x10-8 b. Daily after 14 days < 3x10-9 c. Monthly after 14 days < 5x10-8 d. Yearly after 14 days < 3x10-7 e. 10 years < 1.4 PPM 2.3. Aging at time of shipment < 3x10-9/day 2.4. Voltage a. Dynamic (10 seconds to 10 minutes, no stabilization time) < 3x10-9/10% change b. Static (1 hour stabilization time) < 5x10-9/over voltage range 2.5. Short term < 3x10-11/second root Allan variance After 40 minutes on 2.6. Load < 5x10-9/10% change 2.7. Phase noise a. @ 100 Hz < -135 dBc b. @ 1 kHz < -140 dBc c. @ 50 kHz < -145 dBc

ISOTEMP RESEARCH INC. CODE ID. CHARLOTTESVILLE, VA. USA 31785

PART NO. OCXO 91-30

PAGE OF TOTAL DWG. NO. REV. 2 5 114-597 E

OCXO 91-30
2.8. Retrace Time a. 25 < 1x10-7 @ -30C b. 30 < 5x10-8 @ -30C c. 60 < 2x10-8 @ +25C (After "Time" minutes from turn on, following 12 hours minimum on time, and 24 hours off time. At constant temperature and voltage. Referenced to frequency at off time.) 2.9. Humidity < 1x10-8 (For 100 hours at +60C 90/95% relative humidity) 2.10. Acceleration sensitivity < 12x10-9/g total gamma 2.11. Vibration sensitivity (per axis) a. 125 Hz to 600 Hz < 1.2x10-8/g b. 250 Hz to 1 kHz < 6x10-8/g c. 1 kHz to 2 kHz < 1.2x10-7/g 3. ELECTRICAL FREQUENCY ADJUSTMENT NOTE: The ELECTRICAL FREQUENCY ADJUSTMENT is specified internally by ISOTEMP such that: 1. It will meet the customer specification of >2.2 PPM and <5.2 PPM from +0.3 VDC to the actual reference voltage minus 0.3 VDC. 2. It will not cause excessive frequency drift over the ambient temperature range due to: a. The reference voltage b. The external device controlling the electrical frequency adjustment. 3.1. Range > 2.2 PPM < 3.2 PPM (Cpk > 1.5) (At time of shipment) (Referenced to nominal frequency) 3.2. Control +0.3 VDC to +6.14 VDC 3.3. Center +3.22 VDC 0.2 VDC (Voltage in which the VCO input pin is internally held, by a resistor divider network.) 3.4. Slope negative 3.5. Slope ratio < 2 (The ratio between the maximum and minimum slope over the control voltage range.) 3.6. Input impedance > 20 k 4. INPUT POWER 4.1. Voltage 4.2. Current 4.3. Steady state +10 VDC +3.2/-1 VDC < 800 mA @ turn on < 2.85 Watts @ +25C

ISOTEMP RESEARCH INC. CODE ID. CHARLOTTESVILLE, VA. USA 31785

PART NO. OCXO 91-30

PAGE OF TOTAL DWG. NO. REV. 3 5 114-597 E

OCXO 91-30
5. REFERENCE VOLTAGE 5.1. Voltage 5.2. Current 5.3. Temperature stability 6. ENVIRONMENTAL 6.1. Humidity 6.2. Storage temperature 6.3. Vibration 6.3. Shock (non-operating)

+6.71 VDC 0.27 VDC 2 mA < 0.0055 VDC (Cpk > 1.5) (Over temperature range in 2.1.) MIL-STD-202F, Method 103B, Test Condition B, except +60C (95% R.H. @ +60C, non-condensing, 240 hours) -40C to +85C MIL-STD-202F Method 204D, Test Condition C, except 5 gs peak. (5 gs peak, 55 to 2,000 Hz) 20 gs, 11 ms half-sine in three mutually perpendicular planes in each direction (total 6 shocks), without any degradation in performance. MIL-STD-202F, Method 112C, Test Condition D. Unit must be able to withstand 24 cycles over the storage temperature range with maximum transition time of 20 seconds and a soak time of 1 hour, without any degradation in performance.

6.4. Seal 6.5. Temperature cycling

7. EMITTED NOISE ON SUPPLY LINE The noise generated by the oscillator shall be < -27 dBi below 1 mA rms at any specific frequency in the range of 150 kHz to 1.2 GHz. Measured per RTCA/DO-160C, section 21, equipment category B. (With a supply source impedance of < 10 at 200 kHz and 49 20% at 5 MHz, the noise generated by the oscillator shall be < -40 dBm at any specific frequency in the range of 150 kHz to 1.2 GHz.) 8. TEST DATA 8.1. ISOTEMP shall maintain data for each unit verifying compliance with sections 1.3. (output level), 2.1. (ambient frequency stability), 2.3. (daily aging rate at time of shipment), 3.1. (electrical frequency adjustment range), and 4.3. (Steady state power) of this specification for a minimum of two years. ISOTEMP shall supply statistical data for the first three shipments verifying compliance with sections 2.1. (ambient frequency stability), 3.1. (electrical frequency adjustment range), and 5.3. (reference voltage temperature stability) of this specification. ISOTEMP shall retain statistical data on all subsequent shipments verifying compliance with sections 2.1., 3.1., and 5.3. of this specification.

8.2.

ISOTEMP RESEARCH INC. CODE ID. CHARLOTTESVILLE, VA. USA 31785

PART NO. OCXO 91-30

PAGE OF TOTAL DWG. NO. REV. 4 5 114-597 E

OCXO 91-30
9. MARKING The unit will be marked with the following information. 9.1. ISOTEMP RESEARCH INC. logo 9.2. Customer part number 9.3. ISOTEMP RESEARCH part number 9.4. Serial number in the form of "S/N WWWWW-NNNN" where WWWWW = Internal ISOTEMP work order number NNNN = The number of unit shipped against the work order 9.5. Date in the form of "DATE YYWW" where YY = Last two digits of the year WW = The number of the week into the year 9.6. VREF NOMINAL = 6.71V 9.7. FREQ. 5.000000 MHz 9.8. Electrical frequency adjustment data in the form of a. "A = +XX.XX" text b. "A+XX.XX" bar code 39, > 0.125" high c. " B = +XX.XX" text (5 spaces over from the other characters.) d. "B+XX.XX" bar code 39, > 0.125" high e. "C = +XX.XX" text f. "C+XX.XX" bar code 39, > 0.125" high Where +XX.XX is the frequency offset from nominal in Hz at the following voltages. for A +0.84 VDC for B +3.36 VDC for C +5.87 VDC 10. MECHANICAL 10.1. Applicable series 10.2. Model number 10.3. Outline drawing OCXO 91 series OCXO 91-30 125-445

ISOTEMP RESEARCH INC. CODE ID. CHARLOTTESVILLE, VA. USA 31785

PART NO. OCXO 91-30

PAGE OF TOTAL DWG. NO. REV. 5 5 114-597 E

You might also like