Professional Documents
Culture Documents
constructive solutions
Environmentally
friendly
polyurethane
resin based abrasion resistant heavy duty
skid resistant surface dressing
Uses
Properties
o
+20 C
-20oC
Tensile strength at
break (MN/m2):
22.2
64.0
16.0
3.8
Advantages
Elastic modulus
2
(MN/m )
1350
2850
Hardwearing.
Flexible - excellent flexural and tensile strengths.
Non-slip - even when wet.
Application instructions
Chemical resistant
Limitations
Description
Temperature limitations
Properties
Colour:
Compressive strength
(BS 6319):
Flexible strength
(BS 6319):
Tensile strength
(BS 6319):
Volume solids:
Hardness:
Density:
Pot life:
Foot traffic:
Vehicular traffic:
Full cure:
o
+5 C
+35oC
80% RH
Substrate temperature:
Preparation
Steel
For optimum adhesion, Cicol NT Slurry is applied without
need of a primer. The steel shall be prepared by abrasive
blast cleaning to a minimum of Sa 2. An angular
Page 1
Cicol NT Slurry
amplitude of at least 100 micro-metre is required.The
slurry must be applied immediately after blasting the steel.
Timber
Aluminium
Mix ratio, A : B : C
Comp. A (resin)
9.65 kg
Comp. B (hardener)
4.60 kg
Komp. C (filler)
35.75 kg
Concrete
Application
The concrete shall be clean, dry and free of laitance.
Mechanical
cleaning
or
abrasive
blasting
is
recommended. Remove oil and grease with suitable
detergents, e.g. Fosroc Cleaner C, see separate data
sheet.
Traffic density
Thickness
Coverage per m
Light traffic
3.0 - 3.5 mm
5.4 - 6.3 kg
Medium traffic
3.5 - 4.0 mm
6.3 - 7.2 kg
Heavy traffic
4.0 - 4.75 mm
7.2 - 8.6 kg
Mix ratio, A : B
2 : 1, bw.
Comp. A (base)
9.06 kg
Comp. B (hardener)
4.53 kg
Mixing
: 25 minutes at +20C.
constructive solutions
Page 2
Cicol NT Slurry
Dressing
Aggregate
Filler
Dynagrip
Dynagrip
Dynagrip
Anti-spark Aggregate
Paricle Size
(mm)
0.4 - 1.0
0.4 - 1.0
1.0 - 3.0
3.0 - 5.0
1.0 - 3.0
Consumption
Gross (kg)
12
12
15
22
15
Consumption
Nett (kg)
8
8
10
16
10
Light
Traffic Density
Medium
Heavy
Anti
-spark
Table 2. The dressing aggregate depends on traffic type and traffic density.
Technical support
Fosroc A provides technical advisory service on-site
assistance and advise in the use of Cicol NT Slurry and
Nitoprime 31DK products.
Cleaning
Cicol NT Slurry should be removed from tools, equipment
and mixers with Seco Rensevske immediately after use.
Hardened material can only be removed mechanically.
Precautions
For further information see product safety data sheet.
Storage
Shelf life
Cicol NT Slurry and Nitoprime 31DK have a shelf life of 12
months when stored in the original, unopened bags, cans or
buckets in warehouse conditions below +35C.
Packaging and yield
Cicol NT Slurry is supplied in packs of 50 kg and 100 kg,
see yield in Table 1.
Nitoprime 31DK is supplied in packs of 4.5 litre and 12.5
litre, yield 0.20-0.25 litre/m, dependent on the porosity and
surface structure.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 3
FO SA/Cicol NT Slurry/05/B