You are on page 1of 83

U.S.

Department of Labor
Occupational Safety and Health Administration
1057 Broad Street
Bridgeport, CT 06604
Phone: (203)579-5581 FAX: (203)579-5516

Citation and Notification of Penalty

To: Inspection Number: 109179937


O&G Industries Inc. Inspection Date(s): 02/07/2010-08/02/2010
and its successors Issuance Date: 08/03/2010
112 Wall Street
Torrington, CT 06790

Inspection Site: The violation(s) described in this Citation


1349 River Road and Notification of Penalty is (are) alleged to
Middletown, CT 06457 have occurred on or about the day(s) the
inspection was made unless otherwise
indicated within the description given below.

This Citation and Notification of Penalty (this Citation) describes violations of the Occupational Safety and Health Act
of 1970. The penalty(ies) listed herein is (are) based on these violations. You must abate the violations referred to in
this Citation by the dates listed and pay the penalties proposed, unless within 15 working days (excluding weekends
and Federal holidays) from your receipt of this Citation and Notification of Penalty you mail a notice of contest to the
U.S. Department of Labor Area Office at the address shown above. Please refer to the enclosed booklet (OSHA 3000)
which outlines your rights and responsibilities and which should be read in conjunction with this form. Issuance of
this Citation does not constitute a finding that a violation of the Act has occurred unless there is a failure to contest as
provided for in the Act or, if contested, unless this Citation is affirmed by the Review Commission or a court.

Posting - The law requires that a copy of this Citation and Notification of Penalty be posted immediately in a
prominent place at or near the location of the violation(s) cited herein, or, if it is not practicable because of the nature
of the employer's operations, where it will be readily observable by all affected employees. This Citation must remain
posted until the violation(s) cited herein has (have) been abated, or for 3 working days (excluding weekends and
Federal holidays), whichever is longer. The penalty dollar amounts need not be posted and may be marked out
or covered up prior to posting.

Informal Conference - An informal conference is not required. However, if you wish to have such a conference
you may request one with the Area Director during the 15 working day contest period. During such an informal
conference you may present any evidence or views which you believe would support an adjustment to the citation(s)
and/or penalty(ies).

If you are considering a request for an informal conference to discuss any issues related to this Citation and
Notification of Penalty, you must take care to schedule it early enough to allow time to contest after the informal
conference, should you decide to do so. Please keep in mind that a written letter of intent to contest must be submitted

Citation and Notification of Penalty Page 1 of 83 OSHA-2(Rev. 6/93)


to the Area Director within 15 working days of your receipt of this Citation. The running of this contest period is not
interrupted by an informal conference.

If you decide to request an informal conference, please complete, remove and post the page 4 Notice to Employees
next to this Citation and Notification of Penalty as soon as the time, date, and place of the informal conference have
been determined. Be sure to bring to the conference any and all supporting documentation of existing conditions as
well as any abatement steps taken thus far. If conditions warrant, we can enter into an informal settlement agreement
which amicably resolves this matter without litigation or contest.

Right to Contest - You have the right to contest this Citation and Notification of Penalty. You may contest all
citation items or only individual items. You may also contest proposed penalties and/or abatement dates without
contesting the underlying violations. Unless you inform the Area Director in writing that you intend to contest
the citation(s) and/or proposed penalty(ies) within 15 working days after receipt, the citation(s) and the
proposed penalty(ies) will become a final order of the Occupational Safety and Health Review Commission and
may not be reviewed by any court or agency.

Penalty Payment - Penalties are due within 15 working days of receipt of this notification unless contested. (See
the enclosed booklet and the additional information provided related to the Debt Collection Act of 1982.) Make your
check or money order payable to "DOL-OSHA". Please indicate the Inspection Number on the remittance.

OSHA does not agree to any restrictions or conditions or endorsements put on any check or money order for less than
the full amount due, and will cash the check or money order as if these restrictions, conditions, or endorsements do not
exist.

Notification of Corrective Action - For each violation which you do not contest, you must notify the Area
Director of the Bridgeport OSHA Area Office, by letter, within 10 calendar days after each abatement date, that you
have taken appropriate corrective action within the time frame set forth on this Citation. Where the citation indicates
that abatement certification is necessary, only the abatement method and date when abatement occurred are required.
Where the citation indicates that abatement documentation is necessary, evidence of the purchase or repair of
equipment, photographs or video, receipts, etc., verifying that abatement has occurred is required. The abatement
letter must be posted at the location where the violation appeared and the corrective action took place or employees
must otherwise be effectively informed about abatement activities. A sample abatement certification letter is enclosed
with this Citation.

Employer Discrimination Unlawful - The law prohibits discrimination by an employer against an employee
for filing a complaint or for exercising any rights under this Act. An employee who believes that he/she has been
discriminated against may file a complaint no later than 30 days after the discrimination occurred with the U.S.
Department of Labor Area Office at the address shown above.

Employer Rights and Responsibilities - The enclosed booklet (OSHA 3000) outlines additional employer
rights and responsibilities and should be read in conjunction with this notification.

Citation and Notification of Penalty Page 2 of 83 OSHA-2(Rev. 6/93)


Notice to Employees - The law gives an employee or his/her representative the opportunity to object to any
abatement date set for a violation if he/she believes the date to be unreasonable. The contest must be mailed to the
U.S. Department of Labor Area Office at the address shown above and postmarked within 15 working days (excluding
weekends and Federal holidays) of the receipt by the employer of this Citation and Notification of Penalty.

Inspection Activity Data - You should be aware that OSHA publishes information on its inspection and citation
activity on the Internet under the provisions of the Electronic Freedom of Information Act. The information related to
these alleged violations will be posted when our system indicates that you have received this citation, but not sooner
than 30 calendar days after the Citation Issuance Date. You are encouraged to review the information concerning your
establishment at www.osha.gov. If you have any dispute with the accuracy of the information displayed, please
contact this office.

Citation and Notification of Penalty Page 3 of 83 OSHA-2(Rev. 6/93)


U.S. Department of Labor
Occupational Safety and Health Administration

NOTICE TO EMPLOYEES OF INFORMAL CONFERENCE

An informal conference has been scheduled with OSHA to discuss the citation(s) issued on

08/03/2010. The conference will be held at the OSHA office located at 1057 Broad Street,

Bridgeport, CT, 06604 on _____________ at _____________. Employees and/or representatives of

employees have a right to attend an informal conference.

Citation and Notification of Penalty Page 4 of 83 OSHA-2(Rev. 6/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 1 Type of Violation: Serious


29 CFR 1926.21(b)(6)(i): The employer did not comply with any specific regulations that apply to work in dangerous
or potentially dangerous areas where employees were required to enter into confined or enclosed spaces.

a.Site - Employees required to enter into confined spaces were not instructed as to the nature of the hazards involved,
the necessary precautions to be taken and in the use of protective and emergency equipment required.

ABATEMENT NOTE: For the purposes for paragraph (b)(6)(i) of this section, "confined or enclosed space" means
any space having limited means of egress, which is subject to the accumulation of toxic or flammable contaminants or
has oxygen deficient atmosphere. Confined or enclosed spaces include, but are not limited to, storage tanks, process
vessels, bins, boilers, ventilation or exhaust ducts, sewers, underground utility vaults, tunnels, pipelines and open top
spaces more than 4 feet in depth such as pits, tubes, vaults and vessels.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 2 Type of Violation: Serious


29 CFR 1926.24: The employer did not develop and maintain an effective fire protection and prevention program
at the job site throughout all phases of the construction, repair, alteration, or demolition work:

a.Site - An effective fire protection and prevention program was not developed nor maintained.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 5 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

The alleged violations below have been grouped because they involve similar or related hazards that may increase
the potential for injury resulting from an accident.

Citation 1 Item 3a Type of Violation: Serious


29 CFR 1926.28(a): Appropriate personal protective equipment was not worn by employee(s) in all operations
where there was exposure to hazardous conditions:

a.Site: Employees working in the HRSG #1 knockout tank sump area and exposed to drowning hazards were not
wearing personal flotation devices.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 3b Type of Violation: Serious


29 CFR 1926.106(a): Employee(s) working over or near water where the danger of drowning existed, were not
provided with U.S. Coast Guard approved life jacket(s) or buoyant work vest(s):

a.Site: Employees working in the HRSG #1 knockout tank sump area and exposed to drowning hazards were not
provided with personal flotation devices.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 6 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 4 Type of Violation: Serious


29 CFR 1926.65(q)(1): The employer did not develop and implement an emergency response plan to handle
anticipated emergencies prior to the commencement of emergency response operations.

a.Site - An emergency response plan was not developed and implemented.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 5 Type of Violation: Serious


29 CFR 1926.150(e)(1): An alarm system was not established by the employer whereby employees on the site
could be alerted for emergencies:

a.Site - An alarm system had not been established where employees onsite could be alerted for emergencies.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 7 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 6 Type of Violation: Serious


29 CFR 1926.150(e)(2): The alarm code or reporting instructions were not conspicuously posted at phones or at
employee entrances:

a.Site - Alarm codes were not posted.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 7 Type of Violation: Serious


29 CFR 1926.153(j): Container(s) of liquefied petroleum gas (LPG) were stored within building(s):

a.Throughout the Site - Three LPG cylinders were stored indoors.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 8 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 8 Type of Violation: Serious


29 CFR 1926.405(a)(2)(ii)(C): Receptacles for uses other than temporary lighting were installed on branch circuits
which supplied temporary lighting:

a.Gas Compressor Building: Receptacles for temporary power and temporary lighting were installed on the same
branch circuit.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 9 Type of Violation: Serious


29 CFR 1926.453(b)(2)(v): A Safety Harness was not worn and a lanyard attached to the boom or basket when
working from an aerial lift.

a.Power Generation Building, Between CT#1 and CT#2 @ Column G-4: An employee who was working in an
aerial lift was not tied off with a full body harness and lanyard attached.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 9 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 10 Type of Violation: Serious


29 CFR 1926.501(b)(4)(i): Each employee on walking/working surfaces were not protected from falling through
holes more than 6 feet above lower levels, by personal fall arrest systems, covers, or guardrail systems erected
around such holes:

a.Power Generation Building, Alongside CT#1: Employees were not protected from stepping into holes by the use
of covers.

b.Power Generation Building, Alongside CT#2: Employees were not protected from stepping into holes by the use
of covers.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 11 Type of Violation: Serious


29 CFR 1926.502(i)(4): All covers were not secured when installed so as to prevent accidental displacement by the
wind, equipment, or employees:

a.Between HRSG 1 and HRSG2 - Floor hole covers were not secured.

b.Near Water Treatment Building - Floor hole covers were not secured.

c.East side of HRSG #1 - Floor hole covers were not secured.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 10 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 12 Type of Violation: Serious


29 CFR 1926.502(i)(4): All covers were not color coded or marked with the word "HOLE" or "COVER" to
provide warning of the hazard:

a.Between HRSG 1 and HRSG2 - Floor hole covers were not color coded nor marked.

b.Near Water Treatment Building - Floor hole covers were not color coded nor marked.

c.East side of HRSG #1 - Floor hole covers were not color coded nor marked.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 13 Type of Violation: Serious


29 CFR 1926.602(c)(1)(ii): Modifications or additions which will affect the capacity or safe operations of the
equipment or reduce the orginial safety factor were made without the manufacturer's written approval.

a.Outside of Power Generation Building Fork extensions were used on a JLG forklift without the manufacturer's
written approval. Also the capacity tags on the unit had not been updated to reflect the added piece
of equipment.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 11 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 1 Item 14 Type of Violation: Serious


29 CFR 1926.1053(b)(1): When the side rails of portable ladder(s) were unable to extend at least 3 feet above the
landing because of the portable ladder's length, the ladder(s) were not secured at top to rigid support(s) and
grasping devices, such as a grabrail were not provided:

a.Power Generation Building - Where the side rails of a stepladder could not extend above the electrical cabinets,
the ladder was not secured at top to rigid support(s) and a grasping device, such as a grabrail, was
not provided.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

Citation 1 Item 15 Type of Violation: Serious


29 CFR 1926.1053(b)(13): The top or top step of a stepladder was used as a step:

a.Power Generation Building - When accessing the top of an electrical cabinet, workers were using the top step and
top of the stepladder.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 7000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 12 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 1 Type of Violation: Willful


Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employmnent
and a place of employment which were free from recognized hazards that were causing or likely to cause death or
serious physical harm to employees in that employees were exposed to the hazards of falls, drowning and/or
asphyxiation:

a.Site: Workers were exposed to the hazards of falls, drowning and asphyxiation when they were allowed to enter
confined spaces without benefit of air monitoring, fall protection and/or protection from drowning.

ABATEMENT NOTE: Among other methods, one feasible and acceptable means of abatement is to follow
ANSI/ASSE Z117.1-2009, entitled Safety Requirements for Confined Spaces.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 13 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 2 Type of Violation: Willful


Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and
a place of employment which were free from recognized hazards that were causing or likely to cause death or
serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas
through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an
explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in
close proximity to where, ignition sources existed. The following conditions and practices contributed to the
existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power
Generation Building, in between two approximately 115 foot tall Heat Recovery Steam Generators (HRSGs) and
well below the tops of all of those structures; the failure to eliminate open flame ignition sources, including but not
limited to propane heaters; construction work occurring during the gas blow process; individuals other than those
essential to conducting the gas blows working in the area during the gas blow process; and the inability to readily
control the amount of gas and pressure flowing through the main gas fuel line.

On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion
hazard created when a large amount of natural gas was blown at high velocity through CT#1 Main Knockout Drum
Vent Pipe (561-TNK-1002) into the area between the two HRSGs and close to buildings, scaffolding, partially
enclosed work areas, and other structures that were adjacent to the Power Generation Building in which employees
worked and in or around which open flame ignition sources, including but not limited to propane heaters, existed,
construction work was occurring, and numerous employees non-essential to conducting the gas blow were working.

When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or
materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power
Generation Building and all other nearby structures, or horizontally to a location away from structures that could
inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and
all construction activity ceases during the gas blow process; ensure that all workers other than those essential to
conducting the gas blows are removed from the building and area around which the gas blows are occurring; and
ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve
and a gas pressure control valve.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 14 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 15 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 3 Type of Violation: Willful


Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and
a place of employment which were free from recognized hazards that were causing or likely to cause death or
serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas
through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an
explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in
close proximity to where, ignition sources existed. The following conditions and practices contributed to the
existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power
Generation Building, in the area immediately east of the two approximately 115 foot tall Heat Recovery Steam
Generators (HRSGs) and well below the tops of all of those structures; the failure to eliminate open flame ignition
sources, including but not limited to propane heaters; construction work occurring during the gas blow process;
individuals other than those essential to conducting the gas blows working in the area during the gas blow process;
and the inability to readily control the amount of gas and pressure flowing through the main gas fuel line.

On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion
hazard created when a large amount of natural gas was blown at high velocity through CT#2 Main Knockout Drum
Vent Pipe (561-TNK-2002) into the area immediately east of HRSG number 2 and close to buildings, scaffolding,
partially enclosed work areas, and other structures that were adjacent to the Power Generation Building in which
employees worked and in or around in which open flame ignition sources, including but not limited to propane
heaters, existed, construction work was occurring, and numerous employees non-essential to conducting the gas
blow were working.

When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or
materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power
Generation Building and all other nearby structures, or horizontally to a location away from structures that could
inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and
all construction activity ceases during the gas blow process; ensure that all workers other than those essential to
conducting the gas blows are removed from the building and area around which the gas blows are occurring; and
ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve
and a gas pressure control valve.

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 16 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 17 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 4 Type of Violation: Willful


Section 5(a)(1) of the Occupational Safety and Health Act of 1970: The employer did not furnish employment and
a place of employment which were free from recognized hazards that were causing or likely to cause death or
serious physical harm in that the method used to clean the 561 main fuel gas line pipes - blowing natural gas
through them at high velocity - was not implemented in such a way as to protect employees from the hazard of an
explosion caused by venting large amounts of natural gas into areas where it could accumulate and where, or in
close proximity to where, ignition sources existed. The following conditions and practices contributed to the
existence of this hazard: the vent pipe configured close to and below scaffolding, in close proximity to the Power
Generation Building, in the area immediately east of the two approximately 115 foot tall Heat Recovery Steam
Generators (HRSGs) and well below the tops of all of those structures; the failure to eliminate open flame ignition
sources, including but not limited to propane heaters; construction work occurring during the gas blow process;
individuals other than those essential to conducting the gas blows working in the area during the gas blow process;
and the inability to readily control the amount of gas and pressure flowing through the main gas fuel line.

On February 7, 2010, employees were exposed to serious or fatal impact and other injuries from an explosion
hazard created when a large amount of natural gas was blown at high velocity through CT#2 Pilot Gas Filter
Separator "A" Vent Pipe (561- SEP-2000A) into the area immediately east of HRSG number 2 and close to
buildings, scaffolding, partially enclosed work areas, and other structures that were adjacent to the Power
Generation Building in which employees worked and in or around in which open flame ignition sources, including
but not limited to propane heaters, existed, construction work was occurring, and numerous employees non-
essential to conducting the gas blow were working.

When natural gas is chosen for this method of cleaning gas line pipes, feasible means of abatement to eliminate or
materially reduce the hazard are to ensure that the vent pipe is positioned vertically and above the Power
Generation Building and all other nearby structures, or horizontally to a location away from structures that could
inhibit the adequate dispersal of the gas; ensure that any and all ignition sources are eliminated; ensure that any and
all construction activity ceases during the gas blow process; ensure that all workers other than those essential to
conducting the gas blows are removed from the building and area around which the gas blows are occurring; and
ensure the use of devices to control the amount and pressure of gas vented, such as a fast closing pipe shut-off valve
and gas pressure control valve.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 18 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 5 Type of Violation: Willful


29 CFR 1926.20(b)(2): The employer did not initiate and maintain a safety program which provides for frequent
and regular inspections of jobsites, materials, and equipment to be made by a competent person (i.e., a person who
is capable of identifying existing and predictable hazards in the surroundings or working conditions which are
unsanitary, hazardous, or dangerous to employees, and who has the authority to take prompt corrective measures to
eliminate them):

a.Site - A competent person did not conduct frequent and regular inspections of the jobsite, materials and
equipment as required.

ABATEMENT NOTE: A "competent person" means one who is capable of identifying existing and predictable
hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and
which has authorization to take prompt corrective measures to eliminate them.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 19 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 6 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct Employee #1 in the recognition and avoidance of
hazards related to gas blow operations.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 7 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct Employee #2 in the recognition and avoidance of
hazards related to gas blow operations.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 20 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 8 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct Employee #3 in the recognition and avoidance of
hazards related to gas blow operations.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 9 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct Employee #4 in the recognition and avoidance of
hazards related to gas blow operations.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 21 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 10 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct Employee #5 in the recognition and avoidance of
hazards related to gas blow operations.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 11 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Keystone Construction and Maintenance was instructed in the recognition and avoidance of
hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Keystone Construction and Maintenance have been
administratively combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 22 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 12 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Bluewater Energy Services was instructed in the recognition and avoidance of hazards related to
gas blow operations.

NOTE: For penalty purposes, the exposed employees of Bluewater Energy Services have been administratively
combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 23 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 13 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
United Anco Services was instructed in the recognition and avoidance of hazards related to gas
blow operations.

NOTE: For penalty purposes, the exposed employees of United Anco Services have been administratively
combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 24 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 14 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Instrument Sciences and Technology was instructed in the recognition and avoidance of hazards
related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Instrument Sciences and Technology have been
administratively combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 25 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 15 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Coverflex Manufacturing Inc. was instructed in the recognition and avoidance of hazards related to
gas blow operations.

NOTE: For penalty purposes, the exposed employees of Coverflex Manufacturing Inc. have been administratively
combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 26 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 16 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Api
Group Inc. was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Api Group Inc. have been administratively combined into
a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 27 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 17 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Ducci
Electrical Contractors, Inc. was instructed in the recognition and avoidance of hazards related to
gas blow operations.

NOTE: For penalty purposes, the exposed employees of Ducci Electrical Contractors, Inc. have been
administratively combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 28 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 18 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of North
American Energy Services (NAES) was instructed in the recognition and avoidance of hazards
related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of North American Energy Services (NAES) have been
administratively combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 29 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 19 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Siemens Energy was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Siemens Energy have been administratively combined
into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 30 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 20 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Smedley Crane was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Smedley Crane have been administratively combined into
a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 31 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 21 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Tucker Mechanical was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Tucker Mechanical have been administratively combined
into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 32 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 22 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Worley Parsons was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Worley Parsons have been administratively combined into
a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 33 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 23 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of Team
Industrial was instructed in the recognition and avoidance of hazards related to gas blow
operations.

NOTE: For penalty purposes, the exposed employees of Team Industrial have been administratively combined into
a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 34 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 24 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Securitas was instructed in the recognition and avoidance of hazards related to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Securitas have been administratively combined into a
single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 35 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 25 Type of Violation: Willful


29 CFR 1926.21(b)(2): The employer did not instruct each employee in the recognition and avoidance of unsafe
condition(s) and the regulation(s) applicable to his work environment to control or eliminate any hazard(s) or other
exposure to illness or injury:

a.Site - On or about February 7, 2010, O&G failed to instruct each employee or ensure that each employee of
Contech Technical Services Co. was instructed in the recognition and avoidance of hazards related
to gas blow operations.

NOTE: For penalty purposes, the exposed employees of Contech Technical Services Co. have been
administratively combined into a single citation.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 36 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 26 Type of Violation: Willful


29 CFR 1926.352(c): The employer did not ensure that welding, cutting and heating was not performed where the
application of flammable paints, or the presence of other flammable compounds, or heavy dust concentrations
created a hazard.

a.Site - Welding, cutting and heating were performed where flammable compounds created a hazard.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 27 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Between HRSG #1 and HRSG #2 - On February 7, 2010, the Wacker Neuson Ground Heater was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 37 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 28 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.North Wall near Column B2 - On February 7, 2010, the Dryco heater, number 52-13, was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 29 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.South Wall near Column G2 - On February 7, 2010, the Dryco heater, number 51-03, was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 38 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 30 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Subgrid CC+ near Column B6 - On February 7, 2010, the Dryco heater, number 52-14, was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 31 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-2/D-3 near Column G6 - On February 7, 2010, the Dryco heater, number 52-10, was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 39 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 32 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D3 south of Column B8 - On February 7, 2010, the Dryco heater, number 52-13, was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 33 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.North Wall on Column B1 - On February 7, 2010, the Brasch Electric heater was not used as instructed by its
listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 40 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 34 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.On Column D1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or
certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 35 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 on Column G9 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 41 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 36 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.On Column G1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or
certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 37 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-2/D-3 on Column G5 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 42 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 38 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 on Column B8 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 39 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 on Column B9 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 43 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 40 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-2/D-3 on Column G4 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 41 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.On Column G1 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling or
certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 44 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 42 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 on Column G8 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 43 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Subgrid A - On February 7, 2010, the Miller IV Express Welder was not used as instructed by its listing, labeling
or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 45 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 44 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3, north side of Column G8 - On February 7, 2010, the temporary electric breaker panel SE1 was not used
as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 45 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Subgrid A Column C4 - On February 7, 2010, the temporary electrical breaker panel NW1 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 46 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 46 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 southwest of Column C9 - On February 7, 2010, temporary electrical breaker panel NE1A was not used
as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 47 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-2/D-3 Subgrid j-k - On February 7, 2010, the temporary circuit breaker panel SW1 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 47 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 48 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 west side between Columns D9 and E9 - On February 7, 2010, the Heat Stress Unit C121 was not used
as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 49 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 west side between Columns D9 and E9 - On February 7, 2010, the Heat Stress Units C254R, C123 and
C167 were not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 48 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 50 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grids D-2/D-3 Subgrid I - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 51 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 northwest side of Column C9 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 49 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 52 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grids D-2/D-3 Subgrid K - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 53 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grids D-2/D-3 near Column F6 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 50 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 54 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grids D-2/D-3 Subgrid K - On February 7, 2010, the FM Mafco KVA power distribution panel was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 55 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grids D-2/D-3 near Column G6 - On February 7, 2010, the 25 KVA Power Distribution Panel was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 51 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 56 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 First Floor CG13 and CG14 - On February 7, 2010, the Dryco 51-01 heater was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 57 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4, First Floor between CG13 and CG14 - On February 7, 2010, the Brasch heater was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 52 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 58 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4, First Floor between CG9 and CG10 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 59 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4, First Floor between CG10 and CG11 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 53 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 60 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 First Floor bwteen CG12 and CG13 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 61 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D4 Column G10 - On February 7, 2010, the Brasch electric heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 54 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 62 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 Column G12 - On February 7, 2010, the Brasch electric heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 63 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2, 5th Level East Side HRSG #1 - On February 7, 2010, the Heat Stress Unit C161D was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 55 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 64 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2, 5th Level East Side HRSG #1 - On February 7, 2010, the Heat Stress Unit C126 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 65 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 along West Side HRSG #1 - On February 7, 2010, Heat Stress Unit C162 was not used as instructed by
its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 56 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 66 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 Along west side of HRSG #1 - On February 7, 2010, the Heat Stress Unit #241 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 67 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 3rd Level East/West Mezzanine - On February 7, 2010, Miller Mark VIII-2 8 pack welder was not used
as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 57 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 68 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 between CG14 and CG15 - On February 7, 2010, the Red Arc EX300 welders were not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 69 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Floor between CG9 and CG10 - On February 7, 2010, Miller Mark VIII-2 8 pack welder was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 58 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 70 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Floor between CG11 and CG12 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 71 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Floor between CG9 and CG10 - On February 7, 2010, the 25 KVA power distribution panel was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 59 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 72 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 near Column C15 - On February 7, 2010, temporary circuit breaker panel NE1B was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 73 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 Southeast of HRSG #1 - On February 7, 2010, temporary circuit breaker panel #1 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 60 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 74 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 between Columns CG14 and CG15 - On February 7, 2010, the Brasch Heater was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 75 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 Column F15 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling
or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 61 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 76 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 2nd Floor Column C15 - On February 7, 2010, the Brasch heater was not used as instructed by its
listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 77 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 2nd Floor Column E15 - On February 7, 2010, the Brasch heater was not used as instructed by its
listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 62 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 78 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 2nd Floor Column G10 - On February 7, 2010, the Brasch heater was not used as instructed by its
listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 79 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Column G12 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 63 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 80 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Floor Column D15 - On February 7, 2010, the Brasch heater was not used as instructed by its
listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 81 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-4 3rd Floor Column F15 - On February 7, 2010, the Brasch heater was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 64 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 82 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-5 Administration Bldg Garage on Column - On February 7, 2010, the Brasch heater (#1) was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 83 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-5 Administration Bldg Garage on Column - On February 7, 2010, the Brasch heater (#2) was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 65 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 84 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 Column G7 - On February 7, 2010, the Brasch heater was not used as instructed by its listing, labeling
or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 85 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 Ground Level South Exterior Wall of Power Generation Bldg - On February 7, 2010, temporary circuit
breaker panel #4 was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 66 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 86 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid C-3, Ground Level, North Side of Power Generation Bldg - On February 7, 2010, the temporary power
distribution shed ("North Shack") was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 87 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid F-4, Ground Level, next to South Side of DI Water Treatment Bldg - On February 7, 2010, the temporary
power distribution shed ("South Shack") was not used as instructed by its listing, labeling or
certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 67 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 88 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-5, Ground Level, next to North Side DI Water Treatment Bldg - On February 7, 2010, the temporary
circuit breaker panel (transformer) for the Keystone trailer was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 89 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 Ground Level West Side of Water Treatment Bldg - On February 7, 2010, the temporary circuit breaker
panel #3 was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 68 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 90 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, SE of HRSG #2 - On February 7, 2010, the temporary circuit breaker panel #2 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 91 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, the 25 KVA power distribution panel #1 was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 69 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 92 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 5th Level East Side HRSG #1 - On February 7, 2010, the DP-90 25 KVA power distribution panel was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 93 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 HRSG #2 Feedwater Pump Bldg - On February 7, 2010, the FM Mafco 25 KVA power distribution
panel #15 was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 70 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 94 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 East Side HRSG #2, 5th Level East/West Mezzanine - On February 7, 2010, the FM Mafco 25 KVA
power distribution panel #0036335 was not used as instructed by its listing, labeling or
certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 95 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 3rd Level, North/South Mezzanine, East Side - On February 7, 2010, the FM Mafco 25 KVA power
distribution panel #0042385 was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 71 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 96 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid D-3 near Column G7 - On February 7, 2010, the FM Mafco 25 KVA power distribution panel #15 was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 97 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 72 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 98 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
010638) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 99 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
756043) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 73 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 100 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 101 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder was not
used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 74 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 102 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 3rd Level, East/West Mezzanine - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
383582) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 103 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 5th Level, East Side HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
748681) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 75 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 104 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, Ground Level, South of HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
756047) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 105 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2, 5th Level, East Side of HRSG #1 - On February 7, 2010, the Miller Mark VIII-2 8 pack welder (s/n
0038953) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 76 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 106 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 3rd Level North/South Mezzanine, East Side of HRSG #2 - On February 7, 2010, the Miller Mark VIII-
2 8 pack welder (s/n 242861) was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 107 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 3rd Level North/South Mezzanine, East Side HRSG #2 - On February 7, 2010, the Miller Mark VIII-2 8
pack welder was not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 77 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 108 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-2 5th Level East Side HRSG #1 - On February 7, 2010, the DP-90 25 KVA power distribution panel was
not used as instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 109 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, Heat Stress Unit C128 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 78 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 110 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4 3rd Level East/West Mezzanine - On February 7, 2010, the Heat Stress Unit C134 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 111 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-4, 3rd Level, East/West Mezzanine - On February 7, 2010, Heat Stress Unit 227 was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 79 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 112 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 HRSG Feed Water Pump Bldg - On February 7, 2010, the Heat Stress Unit #1 was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 113 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 5th Level, East Side HRSG #2 - On February 7, 2010, Heat Stress Unit C121 was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 80 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 114 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3, 5th Level, North/South Mezzanine - On February 7, 2010, Heat Stress Unit C119 was not used as
instructed by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

Citation 2 Item 115 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 Under HRSG #2 - On February 7, 2010, Heat Stress Unit C142 was not used as instructed by its listing,
labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 81 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 116 Type of Violation: Willful


29 CFR 1926.403(b)(2): Listed, labeled, or certified equipment was not installed and used in accordance with
instructions included in the listing, labeling, or certification:

a.Grid E-3 HRSG Feedwater Pump Bldg. - On February 7, 2010, the Heat Stress Unit #2 was not used as instructed
by its listing, labeling or certification.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 82 of 83 OSHA-2 (Rev. 9/93)


U.S. Department of Labor Inspection Number: 109179937
Occupational Safety and Health Administration Inspection Dates: 02/07/2010 - 08/02/2010
Issuance Date: 08/03/2010

Citation and Notification of Penalty

Company Name: O&G Industries Inc.


Inspection Site: 1349 River Road, Middletown, CT 06457

Citation 2 Item 117 Type of Violation: Willful


29 CFR 1926.501(b)(1): Each employee on a walking/working surface with an unprotected side or edge which was
6 feet or more above a lower level was not protected from falling by use of guardrail systems, safety net systems, or
personal fall arrest systems:

a.Power Generation Building: Employees who were working on the top of an electrical cabinet were exposed to
fall hazards of approximately 8 feet.

b.Site - Employees who were working within HRSG #1 knockout tank sump area were not protected from falls.

ABATEMENT DOCUMENTATION REQUIRED FOR THIS ITEM

Date By Which Violation Must be Abated: 08/09/2010


Proposed Penalty: $ 70000.00

__________________________________________________
Robert W. Kowalski
Area Director

See pages 1 through 4 of this Citation and Notification of Penalty for information on employer and employee rights and responsibilities.

Citation and Notification of Penalty Page 83 of 83 OSHA-2 (Rev. 9/93)

You might also like