You are on page 1of 48

UMTS

Analysis Guide

November 2005

www.actix.com

The content of this manual is provided for information only, is subject to change without notice, and should not be construed as a commitment by Actix. Actix assumes no responsibility or liability for any errors or inaccuracies that appear in this documentation. Copyright Actix 2005-2008. All rights reserved. All trademarks are hereby acknowledged.

www.actix.com

Contents
1 INTRODUCTION .........................................................................................4 2 OPERATIONAL TASKS AND PROCESSES .............................................................5
2.1 SITE INTEGRATION AND INFRASTRUCTURE TESTING .................................................... 7 2.2 DETAILED CALL SEQUENCE ANALYSIS .................................................................... 8 2.3 BENCHMARKING AND STATISTICAL ANALYSIS ............................................................ 9 2.4 RADIO LINK PERFORMANCE TROUBLESHOOTING........................................................10

3 FEATURE OVERVIEW ................................................................................. 12


3.1 ACTIX ANALYZER ...........................................................................................12 3.2 APPLICATION LAYERS ......................................................................................13 3.2.1 Neighbor List Analysis Module ...............................................................14 3.2.2 CPICH Pollution Analysis Module ............................................................17 3.2.3 Handoff State Analysis Module (for scanner) ...........................................19 3.2.4 Emulated Active Set Module..................................................................22 3.2.5 CPICH before RRC Connection Request Module ........................................23 3.2.6 CPICH before call end or drop Module.....................................................24 3.2.7 CPICH during call Module......................................................................25 3.2.8 CPICH after call end or drop Module .......................................................26 3.2.9 Call Setup Status Module......................................................................27 3.2.10 Call Sequence Analysis Module ............................................................28 3.2.11 Call Statistics Module (CS or PS)..........................................................29 3.2.12 Call Sustainability Module ...................................................................30 3.2.13 Call Timing Analysis Module ................................................................31 3.2.14 File Summary Module.........................................................................32 3.2.15 Coverage Summary Module ................................................................33 3.2.16 Handoff Breakdown Analysis Module (Handset) ......................................34 3.2.17 SHO per event 1a-1b-1c Module ..........................................................35 3.2.18 Overall BLER Module ..........................................................................36 3.2.19 BLER Per call Module ..........................................................................36 3.2.20 BLER during SHO Module ....................................................................37 3.3 FILTERS .....................................................................................................37 3.4 STATEFORMS................................................................................................38 3.4.1 UMTS Data Event Navigator ..................................................................38 3.4.2 UMTS Data Session .............................................................................39 3.4.3 UMTS Throughput ...............................................................................40 3.4.4 UMTS Top 10 Scan Measurements .........................................................41 3.4.5 UMTS UE Active + Monitored Set ...........................................................42 3.4.6 UMTS UE Call Information.....................................................................43 3.4.7 UMTS UE Measurements Charts.............................................................44 3.4.8 UMTS UE Radio Parameters ..................................................................45 3.4.9 UMTS UE Transport Channel Info ...........................................................46 3.4.10 UMTS Voice Event Navigator (CS Only) .................................................47

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Introduction 4

1 Introduction
It is widely recognized that increasing productivity fuelled much of the global economic expansion of the 1990s. Technological advances in software and hardware usually enable these productivity improvements, although there is often a lag between the availability of the new technology, and its widespread acceptance and deployment by industry. This gap is sometimes called the productivity lag factor. Some examples of this include the introduction of automated bank teller technology in the 1980s in the US. When the technology initially became available, it was only sparingly deployed, and the units were often placed inside bank buildings where the productivity enhancements they offered were limited. Likewise, unattended gasoline pump technology has been slow to roll out in Europe, but as the technology has become widely adapted, huge efficiency gains have been realized. The wireless industry is now at a similar point. It understands that the traditional laborintensive techniques for maximizing performance and capacity in wireless infrastructure are fundamentally limited by a lack of structured algorithms to determine improvements. Actix Analyzer offers the possibility to look at drive test data and scanner data to fully optimize a UMTS network. It allows the engineer to understand the causes and reasons for drop calls and access failures. Analyzer offers an unprecedented capability to execute a detailed examination of message flows and automating statistical analyses of performance. Analyzer significantly accelerates the rollout, troubleshooting and optimization of the UMTS network. Actix has embedded intelligence in the software to allow the RF engineer to visualize specific events and understand real problems occurring in the network. Analyzer embodies our extensive experience as the market leader in optimization solutions for CDMA, UMTS and GSM. All of the lessons learned and the techniques developed over a 10-year period have been incorporated into these powerful, vendor-independent solutions for UMTS infrastructure. This document provides an overview of the key benefits, applications and features of Analyzer. For additional information, including white papers and other literature, please refer to www.actix.com.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 5

2 Operational Tasks and Processes


Actix Solutions embody our extensive experience as the market leader in optimization solutions for CDMA, UMTS and GSM. All of the lessons learned and the techniques developed over a 10-year period have been incorporated into these powerful, vendorindependent solutions for cdma2000, GPRS and UMTS infrastructure. Analyzers Rollout Verification is a novel solution to the challenge of rolling out, troubleshooting and optimizing real UMTS networks. Analyzer may be used in field trial, benchmarking and operational settings to automate the process of quantifying network performance, thereby mitigating the risk of performance problems during commercial operation. Analyzer offers an unprecedented capability to execute a detailed examination of message flows and automating statistical analyses of performance. Analyzer significantly accelerates the rollout, troubleshooting and optimization of the UMTS network. Actix has embedded intelligence in the software to allow the RF engineer to visualize specific events and understand real problems occurring in the network. Applications addressed by Analyzer first become pertinent during the new technology rollout, as shown in Figure 1. Then, as first-generation technology is rolled out for soft or commercial launches, Analyzer continues to address a number of critical challenges. As new sites are coming on air and more customers are accessing the network, the real challenge for the RF engineer is to maximize the coverage, capacity and quality of service. Analyzer offers a number of applications applicable to these ongoing challenges.

Rollout Verification S l R&D Trials Initial Rollout Immature Buildout Mature Growth

Figure 1: Applicability of Analyzer begins in the Initial Rollout and continues throughout the lifecycle of the network deployment

Analyzer is a powerful tool designed to help the RF engineer analyze data from scanner and handset sources. It gives a detailed analysis during the whole drive route. From missing neighbor to pilot pollution detection, the different embedded events give an absolute advantage to the RF engineer in understanding the source of different problems. Figure 2 depicts some of the major processes performed by engineering teams during the initial rollout, immature buildout and mature growth phases; and indicates the key radiolink configuration tasks that are common across these processes. The following sections provide an outline (plus additional details) of the processes and tasks typically performed during those phases.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 6

R&D / Trials & Planning

Initial Rollout

Immature Buildout

Mature Growth

Phases

Site Calibration Initial Testing

Initial Coverage Analysis

Processes

Subscriber-Perceived Performance

Radio Link Performance

On-going Optimization

Network Growth

Power Measurements

Site Integration and Optimization

Service Coverage Availability

Throughput and Rates Calculation

Event Detections

Tasks

Scanner and Drive Tests Analysis

Benchmarking

Figure 2: Scanner and Drive tests analysis, Site Integration and Optimization are performed as part of critical processes in the Initial Rollout, Immature Buildout and Mature Growth phases

Analyzer allows the user to focus on the following tasks for site integration and testing, coverage analysis, troubleshooting and optimization:

Site Integration and Infrastructure Testing Detailed Call Sequence Analysis Benchmarking and Statistical Analysis Radio Link Performance Troubleshooting Event Detection and Drive Test Analysis

The following sections describe the high-level capabilities of Analyzer for each of these applications. Because Analyzer is based on an open architecture platformwhich includes
www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 7

user-definable query and open data import capabilitiesit may be used for many ad-hoc troubleshooting and performance analysis tasks beyond those covered in this document.

2.1 Site Integration and Infrastructure Testing


Part of the process in rolling out a network is to be able to test and integrate new sites. Analyzer provides the following features for site integration and infrastructure testing:

The file summary report allows the engineer to have a quick look at the overall performance during the entire drive test. Embedded charts and graphs help to visualize key parameters like Ec/No or RSCP in the active set. Detailed reports on call statistics on cell by cell basis User-definable queries allow creation of customized statistical analysis Automated report generation containing statistical summaries of key performance indicator

Figure 3: Charts and graphs for UMTS site integration and infrastructure testing

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 8

2.2 Detailed Call Sequence Analysis


Analyzer provides these analyses of call sequence and call setup procedures:

Detailed call sequence analysis on a message by message basis Automated report generation for visualization of call sequence messages Automated report generation statistical summaries of call setup problems

Figure 4: Statistical summaries of call setup procedures and failure causes

Figure 5: Detailed call sequence analysis

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 9

2.3 Benchmarking and Statistical Analysis


Analyzer provides the following features for benchmarking and statistical analysis:

Automated report generation for quick visualization of call statistics such as drop calls, access failures, call sustainability, etc. Working with different sources of data to create homogeneous set of reports for benchmarking User-defined queries allowing easy access to different statistics

Figure 6: Charts and graphs representing different call statistics

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 10

Figure 7: Various call statistics filtered by cells

2.4 Radio Link Performance Troubleshooting


Analyzer may be used to diagnose and determine remedial action for key radio-link configuration problems, including:

Distant servers Too many servers Unnecessarily large neighbor lists Excessive soft handoff area

Figure 8: Identify problems for UMTS radio networks by visualizing pilot signals as lines drawn to serving cells on a map

Radio Link Performance Metrics available from Analyzer will include the following attributes, depending on the specific vendor and specific source (handset or scanner):
www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Operational Tasks and Processes 11

Mobile Transmit Power, Mobile Receive Power, BLER CPICH Ec/No, Ec/Io and RSCP per scrambling code Chip Offset and Delay Spread per SC Ec/Io, RSCP and Pathloss for Nth best SCs CPICH Ec/No and SC in Active and Monitored set Handoff State, Call ID

Figure 9: Charts and graphs for a handoff state analysis

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 12

3 Feature Overview
3.1 Actix Analyzer
Depending on the licenses available to you, Analyzer is able to analyze cdma2000, GSM, GPRS and EDGE, as well as UMTS data. Analyzer provides a core set of capabilities to analyze network performance data:

Interfaces to a large number of network performance data sources Support for a wide variety of wireless protocols from the air-interface to the core network Filtering and binning module Finite state event detection engine Time-series and multi-dimensional statistical query module Data merging and synchronization / correlation module Mapping, charting, and reporting modules Messaging and protocol stack browsers Network element database Open data import and export module

Analyzers flexibility allows it to be configured for a wide range of network performancedata analysis tasks.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 13

3.2 Application Layers


Application Layers can be added to Analyzer to implement task or application specific functionality. Analyzer includes the following application layers: UMTS Accelerated Network Rollout Solution

Neighbor List Analysis Module Handoff State Analysis Module CPICH Pollution Module Emulated Active Set Module

UMTS CPICH Level Analysis CPICH before RRC Connection Request Module CPICH before call end or drop Module CPICH during call Module CPICH after call end or drop Module

UMTS Call Setup Analysis Call Setup Status Module Call Sequence Analysis Module

UMTS Call Statistics Call Statistics Module Call Statistics PS Module Call Sustainability Module Call Timing Analysis Module

UMTS Drive Test Summary File Summary Module Coverage Summary Module

UMTS Handoff Analysis Handoff Breakdown Analysis Module SHO per event 1a-1b-1c Module

UMTS Quality Analysis Overall BLER Module BLER Per call Module BLER during SHO Module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 14

3.2.1 Neighbor List Analysis Module


The Neighbor List Analysis provides an automated approach for generating optimal neighbor lists and overcoming major service-degrading problems such as missing neighbors. The key components of the neighbor-list analysis module are: Generation of recommendations for optimal neighbor list settings based on UMTS/WCDMA scanner drive test data. Integration with Network Element Database to audit existing neighbor lists and suggest changes, and to correlate non-unique measured data attributes such as Scrambling Code with unique identifiers such as Sector ID. The Neighbor List Module implements the following algorithm: Ec/Io measurements below a noise floor are filtered out of the data set before analysis. User definable binning is used to reduce the number of measurements points in each bin to create one value per bin optionally, no binning at all can be applied and the analysis will run on the full data set. At each point along the drive test, a list of prospective neighbors is accumulated as indicated in Figure 19. If a neighbor signal is within a user-definable threshold of the best server in the active set, then it is considered as a potential neighbor. Using the geographic information in the log file and the SC, the network element database is searched to identify the Sector and Cell IDs of the SC. A symmetrical neighbor array is created in memory which records the number of times each sector ID is seen as a prospective neighbor of another sector ID as shown in Table 1. Once all bins in the log file have been compiled into the symmetrical matrix, the results are compared against actual neighbor lists contained in the network element database and the following are calculated:

a list of sector IDs included in the matrix, but not the actual neighbor list a list of sector IDs included in the actual list but not in the matrix

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 15

C Neighbour 2

D Not a Neighbour

A Best Server B Neighbour 1

Drive Test Route

E Excluded from Analysis

Figure 19: Cell A is the best server by CPICH Ec/Io. Cells B and C are within a user-specified threshold of Cell As Ec/Io, and so are counted as potential neighbors of A. Cell D is not within the required threshold and so is not counted as a prospective neighbor, nor is Cell E which did not have a measurable signal contribution at this point in the drive test.

A A B C D N/A 10 2 15

B 10 N/A 40 0

C 2 40 N/A 12

D 15 0 12 N/A

Table 1: A sample symmetric prospective neighbor array using sector IDs A, B, C, and D

Limitations of the algorithm: Results are only produced in areas that have been tested, so the test areas should be carefully considered before removing any Sectors from the neighbor lists Drive tests do not necessarily emulate the radio environment encountered by pedestrian and in-building users; however, walk tests and in-building tests may be included in the analysis as desired Results are presented in the following application reports:

Neighbor List Summary

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 16

Neighbor List Audit Recommended Neighbor Lists

Figure 20: A sample Recommended Neighbor Lists report

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 17

3.2.2 CPICH Pollution Analysis Module


The CPICH or Pilot Pollution Analysis uses an emulated Active Set to estimate which pilots would have been actively demodulated by the UE, and then detects other pilots above a user-definable threshold that cause excessive interference. Please see the Emulated Active Set Module section for more details on how the Active Set is estimated based on WCDMA scanner measurements. The pilot pollution algorithm has these components:

Ec/Io measurements below a noise floor are filtered out of the data set prior to analysis. User definable binning is used to reduce the number of measurements points in each bin to create one value per bin optionally, no binning at all can be applied and the analysis will run on the full data set. At each point along the drive test, CPICH Ec/Io data for each Scrambling Code is used to assign SCs to an Active Set or a Pollution Set (please see the Emulated Active Set Module section for more details). The Pollution Set consists of all SCs that are not in the Active Set, and have a CPICH Ec/Io within a user specified pollution threshold of the strongest CPICH Ec/Io in the Active Set (see Figure 21). Using the geographic information in the log file and the SC, the network element database is searched to identify the Sector and Cell IDs of the SC. A pollution array is created in memory which records the number of times each sector ID is seen as a source of pilot pollution as shown in Table 2 All bins in the log file are then processed into the pollution matrix.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 18

D Pollution Source C Active Set

A Active Set Drive Test Route

B Active Set

E Not a Pollution Source, or in Active Set

Figure 21: Cell A, B and C are part of the Active Set, as determined by the Emulated Active Set module. Cell D has a CPICH Ec/Io within a user-specified pollution threshold of the Active Sets best server Ec/Io, and so is counted as a contributor to pilot pollution at this point in the drive test. Cell E has a CPICH Ec/Io that is not within this threshold and so is not a pollution source.

Sector ID A B C D

Pollution Count 0 150 45 12

Table 2: A sample pollution array indicating the number of points at which each sector caused pilot pollution for sector IDs A, B, C, and D

Results are presented in the Pilot Pollution Analysis application report as shown in Figure 22. In addition, Pilot Pollution may be geographically analyzed for each SC by accessing the Pollution_for_SC attribute in the workspace view.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 19

Figure 22: The Pilot Pollution Analysis report indicates the worst interferers sorted by Scrambling Code

3.2.3 Handoff State Analysis Module (for scanner)


The Handoff State Analysis module uses the emulated Active Set to determine the handoff state at each point along a drive test. Statistics on handoff state may then be calculated and presented in a report format. Excessive handoff state reduces capacity and increase infrastructure costs for a given traffic level. Please see the Emulated Active Set Module section for more details on how the Active Set is estimated based on WCDMA scanner measurements. The handoff state algorithm has the following components:

The Active Set of pilots is determined using the Emulated Active Set module Using the geographic information in the log file and the SC, the network element database is searched to identify the Sector and Cell IDs of the SC Handoff state is calculated by determining the configuration of the sectors in the Active Set as shown in Figure 23 All bins in the log file are then processed into the handoff state matrix

Reports showing the percentage of handoff state for each sector and for the total drive test may then be calculated as shown in Figure 24.

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 20

Single-sector

3-way Softer

3 sectors same node B Softer Soft

2 sectors same node B 3-way soft Soft-softer

2 sectors same node B

Figure 23: The Handoff State Analysis examines Sector IDs involved in call at a given drive test point and determines which of the above states applies, based on UMTS scanner data

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 21

Figure 24: A report showing the percentage of drive test in each handoff state for scanner data

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 22

3.2.4 Emulated Active Set Module


CPICH Pollution Analysis and Handoff Analysis are both based on a calculated Active Set, which is determined by the Emulated Active Set module. The Emulated Active Set module implements the 3GPP handoff algorithm and uses scanner Ec/Io measurements in conjunction with user-specific 3GPP handoff thresholds to emulate the Active Set at each point along a drive test. Figure 25 shows a sample set of scanner data for three individual SCs with color and vertical lines indicating transitions of pilots into and out of the Active Set.

Figure 25: Using Scanner Ec/Io measurements to implement 3GPP handoff algorithms for the Active Set

Figure 26 shows the list of attributes available for modification by the user, as indicated in the 3GPP specifications:

Figure 26: Setting 3GPP handoff algorithm attributes including Reporting Range: Hysteresis Event and Time to Trigger Event

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 23

3.2.5 CPICH before RRC Connection Request Module


The CPICH before RRC Connection Request module helps the engineer to understand the environment right before the call started or to be more precise, before the first RRC connection request happens. For every call in the log file, the report can show the following parameters:

Call Identification, based on the attribute Uu_Call_id Time of the first RRC Connection Request for a specific call Site the call was placed, based on the attribute ServingCellid Scrambling Code the call originated on, based on the attribute Uu_ActiveSet_SC_0 Ec/Io of that same Scrambling Code, based on the attribute Uu_ActiveSet_EcNo_0 RSCP of that same Scrambling Code, based on the attribute Uu_ActiveSet_RSCP_0 or the calculated RSCP if the regular RSCP values are not present or were not logged. Site, SC, Ec/Io and RSCP of the Monitored Set if applicable End result of that particular call

For any of these parameters, the module searches 5 seconds before the first RRC Connection Request for the specific details. If it cannot find the parameters during those 5 seconds, the value No Data is shown. Figure 27 shows a typical analysis executed by the CPICH before RRC Connection Request module. For the engineer, it is an easy way to look at the conditions before the call started and the end result.

Figure 27: Example of a log file analyzed by the CPICH before RRC Connection Request module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 24

3.2.6 CPICH before call end or drop Module


The CPICH before call end or drop module helps the engineer to understand the environment right before the call ended or dropped. For every call in the log file, the report can show the following parameters:

Call Identification, based on the attribute Uu_Call_id Time when the call ended or dropped (see event definitions) Site ID of the active site when the call ended or dropped (attribute ServingCellid) Scrambling Code of the 1st finger in the Active Set Ec/Io of that same Scrambling Code RSCP of that same Scrambling Code Site, SC, Ec/Io and RSCP of the Monitored Set if applicable End result of that particular call

Figure 28 shows a typical analysis executed by the CPICH before call end or drop module. For the engineer, it is an easy way to look at the conditions right before the call ended.

Figure 28: Example of a log file analyzed by the CPICH before call end or drop module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 25

3.2.7 CPICH during call Module


The CPICH during call module helps the engineer to understand the environment during a particular call. For every call in the log file, the report can show the following parameters:

Call Identification Site ID of the most common active site (site associated with the scrambling code of the first finger in the active set) Most common Scrambling Code of 1st finger in the Active Set Average Ec/Io during the entire call Average RSCP during the entire call Site ID of the most common monitored site (site associated with the scrambling code of the first finger in the monitored set) Most common Scrambling Code in the Monitored Set Average Ec/Io during the entire call Average RSCP during the entire call End result of that particular call

Figure 29 shows a typical analysis executed by the CPICH during call module. For the engineer, it is an easy way to look at the average conditions during the call.

Figure 29: Example of a log file analyzed by the CPICH during call module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 26

3.2.8 CPICH after call end or drop Module


The CPICH after call end or drop module helps the engineer to understand the environment right after the call ended or dropped. For every call in the log file, the report can show the following parameters:

Call Identification Time when the call ended or dropped Site ID of the active site when the call ended or dropped Scrambling Code of the 1st finger in the Active Set Ec/Io of that same Scrambling Code RSCP of that same Scrambling Code Site, SC, Ec/Io and RSCP of the Monitored Set if applicable End result of that particular call

Figure 30 shows a typical analysis executed by the CPICH after call end or drop module. For the engineer, it is an easy way to look at the conditions right after the call ended.

Figure 30: Example of a log file analyzed by the CPICH after call end or drop module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 27

3.2.9 Call Setup Status Module


The Call Setup Status module offers a general overview on how and when the call failed. The normal call sequence should go like this:

RRC Connection Request (MOC) or Paging Type1 (MTC) RRC Connection Setup RRC Connection Complete MM CM Service Request (MOC) or Paging Response (MTC) MM CM Service Accept Authentication Request Authentication Accept

Security Mode Command Security Mode Complete CC Setup CC Call Proceeding Radio Bearer Setup Radio Bearer Setup Complete CC Alert CC Connect

If all messages are received properly, the call is a success. If it fails to reach the CC Connect, it should be pegged as a call failure and this module should give the reason for it. Refer to section 3.2 Event Definitions for more details. Figure 31 shows a typical analysis executed by the call setup status module.

Figure 31: Example of a log file analyzed by the call setup status module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 28

3.2.10 Call Sequence Analysis Module


The Call Sequence Analysis module offers a general overview on how call failed and when they failed. This module has the same structure and analysis as the call setup status module except for a few differences. It doesnt summarize as what is the cause of the failure. On the other hand, it gives the call sequence with detailed information on every call and the outcome of it. It gives the engineer the possibility to look at individual calls on a message-by-message basis.

Figure 32: Example of a log file analyzed by the call sequence analysis module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 29

3.2.11 Call Statistics Module (CS or PS)


The Call Statistics Module helps the engineer to have a quick look at the overall performance during a specific drive test. The following parameters' statistics are defined in each file: Total Number of calls: Number of Mobile Originated Calls (MOC) + Number of Mobile Terminated Calls (MTC). This includes all calls, even failures. Successful Incoming Calls: Number of successful Mobile Terminated Calls (MTC). To be successful, a call needs to follow the call sequence as mentioned in section 3.2 Successful Outgoing Calls: Number of successful Mobile Originated Calls (MOC). To be successful, a call needs to follow the call sequence as mentioned in section 3.2 Total Successful Calls: Successful Incoming Calls + Successful Outgoing Calls Connected Percentage: Total Successful Calls/Total number of calls * 100 Call Failures Incoming: Access Failure for a Mobile Terminated Call (MTC) as defined in section 3.2 Call Failures Outgoing: Access Failure for a Mobile Originated Call (MOC) as defined in section 3.2 Access Failure Rate: Total Access Failures/Total number of calls * 100 Total Drops: Total number of dropped calls. A dropped call is defined as one of the following: Drop Rate percentage: Total Drops/Total Successful Calls * 100 Total Completed Calls: Total number of completed calls. A completed call is defined as the following: Success Rate: Total completed calls/Total Successful Calls * 100

Figure 33: Example of a log file analyzed by the Call Statistics Module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 30

3.2.12 Call Sustainability Module


The call sustainability module helps the engineer to have a quick view at the call duration for all calls during the drive route. The statistic is calculated on a per call basis and is the difference in time when the call ends and when the call starts. More precisely: Call Sustainability = Time when RRC Connection request happens (or paging type 1) Time when call drops or ends. Figure 34 shows the call sustainability statistics and the call duration distribution.

Figure 34: Example of a log file analyzed by the call sustainability module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 31

3.2.13 Call Timing Analysis Module


The Call Timing Analysis gives various time statistics on differences between specific messages. In cases where the RRC Connection Request terminology is used, it relates to the first RRC Connection Request message transmitted.

Figure 35: Example of a log file analyzed by the call timing analysis module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 32

3.2.14 File Summary Module


The file summary module helps the engineer to visualize quickly the content of a file. The thresholds for the coverage and quality charts are: Coverage: Good: RSCP > -80 dBm Fair: -80 dBm >= RSCP >= -95 dBm Poor: -95 dBm > RSCP

Quality: Good: Ec/Io > -8 dB Fair: -8 dB >= Ec/Io >= -15 dB Poor: -15 dB > Ec/Io

Figure 36: Example of a log file analyzed by the file summary module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 33

3.2.15 Coverage Summary Module


The file summary module helps the engineer to visualize quickly the statistics related to the strongest RSCP and the strongest Ec/No for a particular file.

Figure 37: Example of a log file analyzed by the coverage summary module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 34

3.2.16 Handoff Breakdown Analysis Module (Handset)


The Handoff State Analysis module for handset uses the Real Active Set from the handset to determine the handoff state at each point along a drive test. Statistics on handoff state may then be calculated and presented in a report format. Excessive handoff state reduces capacity and increase infrastructure costs for a given traffic level. Please see section 3.2.3 for more details on the Handoff State Analysis for scanner. The handoff state algorithm has the following components: Using the geographic information in the log file and the SC, the network element database is searched to identify the Sector and Cell IDs of the SC Handoff state is calculated by determining the configuration of the sectors in the Active Set as shown in Figure 23 Section 3.3.3 All bins in the log file are then processed into the handoff state matrix The Actual SHO Overhead represents the sum of all softhandoff configurations Reports showing the percentage of handoff state for each sector and for the total drive test may then be calculated as shown in Figure 38.
Figure 38: Example of a log file analyzed by the handoff state analysis for handset

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 35

3.2.17 SHO per event 1a-1b-1c Module


The SHO per event 1a-1b-1c module gives a brief summary about the different types of handoff that occur in a file. It shows quickly the number of: Addition: Event 1a Removal: Event 1b Replacement: Event 1c

Also, it reports the number of completion for each of those events and calculates a percentage of success.

Figure 39: Example of a log file analyzed by the soft-handover performance module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 36

3.2.18 Overall BLER Module


The overall BLER (Block Error Rate) module gives a brief summary about the distribution and statistical analysis of BLER for an entire file.

Figure 40: Example of a log file analyzed by the Overall BLER module

3.2.19 BLER Per call Module


The BLER per call module gives a summary of the main statistics associated with the BLER on a call-by-call basis. The maximum value The minimum value The average value for that particular call

Figure 41: Example of a log file analyzed by the BLER per call module

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 37

3.2.20 BLER during SHO Module


The BLER during SHO (soft handover) module provides statistics on the downlink transport channel BLER aggregated across all SHOs and on a call-by-call basis (note that only the calls with BLER measurements during the SHO procedure will be included in this report.

Figure 42: Example of a log file analyzed by the BLER during SHO module

3.3 Filters
Filters can be added to Analyzer to implement task or application-specific functionality. Analyzer includes the following pre-defined filters:

Poor Mobile Receive Power CPICH_RSCP_in_ActiveSet[0] < -95 dBm High Mobile Transmit Power UeTransmittedPower > 0 dBm Low Mobile Transmit Power UeTransmittedPower < -30 dBm High Mobile Receive Power CPICH_RSCP_in_ActiveSet[0] > -80 dBm Poor Ec/No CPICH_EcNo_in_ActiveSet[0] < -15 dB High Ec/No CPICH_EcNo_in_ActiveSet[0] > -8 dB

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 38

3.4 Stateforms
Stateforms can be added to Analyzer to implement task or application-specific functionality. Analyzer includes the following stateforms:

UMTS Data Event Navigator UMTS Data Session UMTS Throughput UMTS Top 10 Scan Measurements UMTS UE Active + Monitored Set

UMTS UE Call Information UMTS UE Measurements Charts UMTS UE Radio Parameters UMTS UE Transport Channel Info UMTS Voice Event Navigator

3.4.1 UMTS Data Event Navigator


The UMTS Data Event Navigator stateform allows the engineer to view the entire drive test with just one quick look. During a data session, it is possible to keep track of the following events:

GPRS_PDPContextAct_Successful GPRS_PDPContextDeact_Successful GPRS_Attach_Successful GPRS_Detach_Successful GPRS_PDPContextAct_Failure GPRS_RAU_Successful Event_Task_Start

While keeping track of the current SC in the active set. Figure 42 shows an example of those different events at different moments in time with the track at the top showing the SC.

Figure 43: Example of a log file analyzed by the UMTS Data Event Navigator Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 39

3.4.2 UMTS Data Session


The UMTS Data Session stateform allows the engineer to view the data testing information collected during a data session.

Figure 44: Example of a log file analyzed by the UMTS Data Session Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 40

3.4.3 UMTS Throughput


The UMTS Throughput stateform chart allows the engineer to view the application and IP downlink throughput graphically for the entire drive test. This information comes from the data testing information collected during the drive test.

Figure 45: Example of a log file analyzed by the UMTS Throughput Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 41

3.4.4 UMTS Top 10 Scan Measurements


The UMTS Top 10 Scan Measurements stateform allows the engineer to view important details regarding the scanner measurements. The following parameters are displayed at any specific moment during the drive test replay:

Top 10 Scrambling Code based on their Ec/Io Top 10 Ec/Io for these respective SC Top 10 RSCP for these respective SC Global RSSI

Figure 46: Example of a log file analyzed by the UMTS Top 10 Scan Measurements Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 42

3.4.5 UMTS UE Active + Monitored Set


The UMTS UE Active + Monitored Set stateform allows the engineer to visualize rapidly the content of the active and monitored sets at any specific moment during the drive test. The following parameters are represented for both the active and the monitored sets.

The Scrambling Code The Ec/No for each of those scrambling code The RSCP for each of those scrambling code The Pathloss if applicable

It is a very quick way for the engineer to follow the active and monitored sets. Using the replay tool, the engineer can follow the drive test and analyze very quickly any particular events.

Figure 47: Example of a log file analyzed by the UMTS UE Active + Monitored Set Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 43

3.4.6 UMTS UE Call Information


The UMTS UE call information stateform allows the engineer to have a quick view at the following events:

IMSI Mobiles Identification number used for testing Called Party Number called for that particular test/call Calling Party In case of mobile terminated calls, the number of the party that called Call id The call identification based on the UMTS call tracker Call State The state the mobile is on. Different states are: Init Idle RRC Con Request RRC Con Setup RRC Setup Complete Outgoing Call Setup Incoming Call Setup

Paging In Call Security Mode Command Security Complete CC Setup Authentication Request Authentication Response CC Call Proceeding RAB Setup RAB Complete Channel Reconfig Radio Bearer Reconfig GSM Mode LAC RAC

Figure 48: Example of a log file analyzed by the UMTS UE Call Information Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 44

3.4.7 UMTS UE Measurements Charts


The UMTS UE Measurements Charts stateform allows the engineer to look at the most important information in a log file. It is very easy to visualize rapidly the following parameters:

EcNo Uu_ActiveSet_EcNo RSSI UTRA_UE_CarrierRSSI TxPower UE_TxPow SIR Uu_SIR SIR_Target Uu_TargetSIR

Figure 49: Example of a log file analyzed by the UMTS UE Measurements Charts Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 45

3.4.8 UMTS UE Radio Parameters


The UMTS UE Radio Parameters stateform allows the engineer to view radio parameters at a specific moment during the drive test. The available parameters are:

TxPower RSSI SIR SIR Target UTRA_ARFCN_DL

Figure 50: Example of a log file analyzed by the UMTS UE Radio Parameters Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 46

3.4.9 UMTS UE Transport Channel Info


The UMTS UE Transport Channel Info allows the engineer to visualize the BLER per channel and also the aggregate BLER.

Figure 51: Example of a log file analyzed by the UMTS UE Transport Channel Info Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 47

3.4.10 UMTS Voice Event Navigator (CS Only)


The UMTS Voice Event Navigator stateform allows the engineer to view the entire drive test with just one quick look. During a session, it is possible to keep track of the following events:

Uu_OutgoingCallOK Uu_IncomingCallOK Uu_OutgoingCallSetupFail Uu_IncomingCallSetupFail Uu_CallDropped Uu_CallCompleted

While keeping track of the current SC in the active set. Figure 51 shows an example of those different events at different moments in time with the colored track at the top showing the SC.

Figure 52: Example of a log file analyzed by the UMTS Voice Event Navigator Stateform

www.actix.com

Actix Analyzer UMTS Analysis Guide November 2005

Feature Overview 48

www.actix.com

You might also like