You are on page 1of 19

PVS SERIES VARIABLE VOLUME PISTON PUMP

Discharge port

PVS Series Variable Volume Piston Pumps

8.0 to 45.0cm3/rev 21MPa

M 0

*
Suction Drain port port

A
Piston Pumps

Design No. 30 is applied on PVS-0B to make the pump more compact and lighter, and reduce noise. Production of PVS-3B has been discontinued. Use PZS-3B. Pressure adjustment 3 type has been added to PVS-1B-22 and PVS-2B-45. (Design No. 20 is applied only on PVS-2B-45*3.)

Features
Energy-saving Type with Drastically Reduced Loss
A NACHI-proprietary semi-circular barrel swash plate that receives pressure on its surface ensures a stable discharge volume at all times. This eliminates excess discharge volume, and enables the effective use of power corresponding to the load cycle. This "energy-saving type" conserves energy, reduces power loss, and helps to reduce hydraulic costs.

Silent Type That Demonstrates Its Power Quietly


Proprietary low-noise mechanisms are incorporated on the shoe, swash plate, valve plate, and other locations to ensure silent operation. In particular, a semi-circular barrel swash plate stabilizes operation characteristics to ensure silent operation.
Permitted peak pressure MPa {kgf/cm2} 25 {255}

Specifications
Model No. Volume cm3/rev Discharge volume at no-load r/min 1000min-1 PVS-0B-8*0-30 1 2 3 PVS-1B-16*0-(*)-12 1 2 3 PVS-1B-22*0-(*)-12 1 2 3 PVS-2B-35*0-(*)-12 1 2 3 PVS-2B-45*0-(*)-12 1 2 3-(*)-20 1200min-1 1500min-1 1800min-1

Pressure adjustment range MPa {kgf/cm2} 2 to 2 to 3 to 3 to 2 to 2 to 3 to 3 to 2 to 2 to 3 to 3 to 2 to 2 to 3 to 3 to 2 to 2 to 3 to 3 to 13.5 {20.4 to 35.7} 17.5 {20.4 to 71.4} 14. 5 {30.6 to 143 } 21. 5 {30.6 to 214 } 13.5 {20.4 to 35.7} 17. 5 {20.4 to 71.4} 14 .5 {30.6 to 143 } 21. 5 {30.6 to 214 } 13.5 {20.4 to 35.7} 17. 5 {20.4 to 71.4} 14. 5 {30.6 to 143 } 21. 5 {30.6 to 214 } 13.5 {20.4 to 35.7} 17. 5 {20.4 to 71.4} 14 .5 {30.6 to 143 } 21.{ 30.6 to 214 } 13.5 {20.4 to 35.7} 17. 5 {20.4 to 71.4} 14. 5 {30.6 to 143 } 21 .5 {30.6 to 214 }

Rotating speed min-1 Min. Max.

Mass kg

8.0

8.0

9.6

12.0

14.4

500

2000

7.7

16.5

16.5

19.8

24.7

29.7

25 {255}

500

2000

10.5

22.0

22.0

26.4

33.0

39.6

25 {255}

500

2000

10.5

35.0

35.0

42.0

52.5

63.0

25 {255}

500

2000

21

45.0

45.0

54.0

67.5

81.0

25 {255}

500

2000

21

Note) 1. The standard direction of rotation is clockwise when viewed from the shaft end. Consult your agent separately for a counterclockwise direction of rotation. 2. A keyed straight shaft is standard. For details on spline shafts, consult your agent separately.

Handling Cautions during Pump Installation and Piping


zUse flexible couplings for connecting the pump shaft to the drive shaft, and prevent a radial or thrust load from being applied on the pump shaft. xFor centering of the pump shaft, limit the eccentricity between the drive shaft and hydraulic pump shaft to 0.05 mm, and keep the angle error within 1. cSet the clamping length of couplings and hydraulic pump shafts so that it is within at least 2/3 or more of the coupling width. vUse a sufficiently rigid pump mounting base. bSet the pressure on the pump suction side to -0.03 MPa or more (suction port flow velocity within 2 m/sec). nRaise part of the drain piping to above the topmost part of the pump body, and

insert the return section of the drain piping into the hydraulic operating fluid. Also, observe the values in the following table to limit the drain back pressure to 0.1 MPa.
Item
Model No.

PVS-0B PVS-1B
3/8" or more

PVS-2B
1/2" or more

Pipe joint size

Pipe I.D Pipe length

7.6 mm dia or more


1m or less

12 mm dia or more
1m or less

Management of Hydraulic Operating Fluid


zUse good-quality hydraulic operating fluid, and use within a kinematic viscosity range of 20 to 200 mm 2/sec during operation. Use an R&O type and antiwear hydraulic fluid of ISO-VG32 to 68. The optimum kinematic viscosity during operation is 20 to 50 mm2/sec.

xThe operating temperature range is 5 to 60C. When the oil temperature at startup is 5C or less, warm up the hydraulic pump by low-pressure, low-operation speed operation until the oil temperature reaches 5C. cProvide a suction strainer with a filtering grade of about 100m (150 mesh). Be sure to provide a return line filter of grade 20m or less on the return line to the tank. (When the hydraulic pump is used at a high pressure of 14 MPa or more, we recommend providing a filter of 10m or less. vManage the hydraulic operating fluid so that contamination is maintained at class NAS10 or lower. bUse hydraulic operating fluid within an operating ambient temperature of 0 to 60C. (continued on following page)

A-3

A
Piston Pumps

zBefore you start pump operation, fill the pump body with clean hydraulic operating fluid via the lubrication port.
Model No. PVS-0B-8 PVS-1B-16, 22 PVS-2B-35, 45 Injection amount cm3 220 300 650

Discharge volume

Cautions at Startup

Discharge volume adjustment range

vAir entering the pump or pipes may cause noise or vibration. At startup, set the pump discharge side to a no-load state, and operate the pump in the inching mode to release any air in the pump or pipes. bProvide an air bleed valve in circuits where it is difficult to release air at startup. (See "IP Pumps" on page C-13.)

Discharge volume

[Pressure adjustment] Turning the pressure adjusting screw CW increases the pressure. [Discharge volume adjustment] Turning the flow rate adjusting screw CW decreases the discharge volume.

CW CCW
Pressure
Pressure adjustment range

CW CCW

How to Set Pressure and Discharge Volume


The default pump discharge volume is set to "maximum" and default discharge pressure is set to "minimum". Change the discharge volume and discharge pressure settings according to your particular operating conditions.

Pressure

xAn unload is required when the motor is started under condition _ 3. Consult your agent regarding the circuit. cMake sure that the pump operates in the direction of rotation the same as that indicated by the arrow on the pump body.

Note) For details regarding the relationship between flow rate adjustment length rand pump capacity q, see the tables provided in the installation dimension drawings for each of the pumps. Firmly tighten the lock nuts after you have finished adjustments.

[Note] Variable control mechanism


Standard type N* : Pressure compensation type (manual mode) Option type

Explanation of model No
PVS 1 B 16 N 2 ( * ) 12
Design No. 30: PVS-0* 12: PVS-1*, PVS-2* 20: PVS-2*-45N3 only Auxiliary symbol None: Side port type Z: Axial port type (PVS-1*, PVS-2*) Pressure adjustment range [Note] Reference Variable control mechanism [Note] Reference Max. pump capacity (cm /rev) Nominal 8, 16, 22, 35, 45 Mounting method B: Mounting flange type Pump size 0, 1, 2 PVS series variable piston pump A: Mounting foot type
3

P* N*Q* R*A& S* W*A& S*

: Pressure compensation type (remote control mode) : 2-pressure, 2-flow rate control : Solenoid cutoff control : 2-pressure control

RQ*A& : 2-pressure, 2-flow rate S* control w/ solenoid cutoff C*A& S* : 2-cutoff control

* : Pressure adjustment range


0 : 2 to 3.5MPa {20.4 to 35.7kgf/cm2} 1 : 2 to 7MPa {20.4 to 71.4kgf/cm2} 2 : 3 to 14MPa {30.6 to 143kgf/cm2} 3 : 3 to 21MPa {30.6 to 214kgf/cm2} * : Applicable to solenoid specifications A, S & A&: SA-G01 * S&: SS-G01 * 1 : 100V 50/60Hz 2 : 200V 50/60Hz 3 : DC12V 4 : DC24V

Discharge volume

Discharge volume

Discharge volume

[Example 1] N*: Pressure compensation type (manual mode) PVS-1B-16N2

N2:3-14MPa

[Example 2] P*: Pressure compensation type (remote control mode) PVS-1B-16P2

P2:3-14MPa

[Example 3] N*Q*: 2-pressure, 2-flow rate control PVS-1B-16N2Q1

Q1:2-7MPa

N2:3-14MPa

Discharge pressure Discharge volume Discharge volume

Discharge pressure

Discharge pressure Discharge volume

[Example 4] R*S*: Solenoid cutoff control PVS-1B-16R2S2 Solenoid specifications 200V 50/60Hz SS-G01

P2:3-14MPa

sol"ON"

[Example 5] W*S*: 2-pressure control PVS-1B-16W2S1 Solenoid specifications 100V 50/60Hz SS-G01

W2:3-14MPa

sol"ON" sol"OFF"

[Example 6] RQ*S*: 2-pressure, 2-flow rate control w/ solenoid cutoff PVS-1B-16RQ2S1 Solenoid specifications 100V 50/60Hz SS-G01

R2:3-14MPa sol"ON"

sol"OFF"
Discharge pressure Discharge pressure

sol"OFF"
Discharge pressure

[Example 7] C*S*: 2-cutoff control PVS-1B-16C2S2 Solenoid specifications 200V 50/60Hz SS-G01

Discharge volume

C2:3-14MPa

sol"ON"

sol"OFF"
Discharge pressure

NQ, RS, WS, RQS and CS types are not available for the PVS-0B-8, and the NQ, RQS and CS types are not available for the PVS-1B-16-Z and PVS-2B-35-Z. 22 45

A-4

Variable Control Mechanisms


Standard type
Symbol External View Discharge volume Drain port Pressure adjusting screw Characteristics Hydraulic Circuit
Discharge port

A
Explanation

Piston Pumps

Flow rate adjusting screw N

M 0

*
Suction Drain port port

Discharge pressure

Pressure compensation type (manual system) When the discharge pressure reaches the preset volume set by the pressure compensator, the discharge volume is automatically reduced to hold the pressure at the set pressure.

NACHI

Option type
Discharge volume Pilot port Flow rate adjusting screw P
NACHI

Drain port Differential pressure

adjusting screw (adjustment forbidden)

Discharge Pilotport port

M 0

*
Suction Drain port port Discharge port

Discharge pressure
P2 pressure adjusting screw

Pressure compensation type (remote control mode) This mode demonstrates the same characteristics as the manual mode. The discharge pressure can be adjusted by external pilot pressure. The discharge volume can be adjusted manually. Note 2)

Discharge volume

q1 flow rate adjusting screw q2 flow rate Drain port adjusting screw

q1 P1 q2

NQ
NACHI

*
P2 Discharge pressure

M N 0

*
Suction Drain port port

2-pressure, 2-flow rate control type The discharge volume changes in two stages by the pump's built-in sequence valve. This allows conventional high/ low pressure control to be performed on a single pump unit, and save energy in the hydraulic circuit.

P1 pressure adjusting screw

Discharge volume

Discharge port

RS (RA)

Pressure adjusting screw (at solenoid ON) Flow rate adjusting screw

SOL

Drain port

SOL SOL "OFF" "ON"

*
Discharge pressure

M 0

*
Suction Drain port port Discharge port

Solenoid cutoff control type A solenoid valve for unload is integrated into the pressure compensation type to minimize energy loss when pump output is not required. Only a slight amount of heat is generated.

Pressure adjusting screw (at solenoid OFF)

SOL

WS (WA)

Pressure adjusting screw (at solenoid ON) Drain port

Discharge volume

NACHI

Flow rate adjusting screw


NACHI

SOL "OFF"

SOL "ON"

M 0

*
Suction Drain port port

P1 P2 Discharge pressure Discharge volume q1

2-pressure control type Two pressure compensation types can be obtained by switching the solenoid valve ON/OFF. Two types of output control are possible with the actuator set to a constant speed.

P2 pressure adjusting screw (at solenoid ON)

Discharge port

SOL

RQS (RQA)

q2 flow rate adjusting screw q1 flow rate adjusting screw

Drain port

q2

P1 SOL ON SOL OFF

*
M * N 0 Suction Drain

P1 pressure adjusting screw


Differential pressure adjusting screw (adjustment forbidden)

P2 Discharge pressure

port

port

2-pressure, 2-flow rate control type w/ solenoid cutoff The discharge volume can be changed in two stages by the sequencer valve and solenoid valve for unload mounted on the pump, and unloading is possible when pressure oil is not required.

NACHI

Discharge volume

q1 flow rate adjusting screw q2 flow rate Drain port adjusting screw

q1

Discharge port

CS (CA)
NACHI

q2

SOL ON

*
P1 SOL OFF P2 Discharge pressure

M N 0

*
Suction Drain port port

2-cutoff control type Two types of pressure - flow rate characteristics can be obtained by the solenoid valve and cylinder mounted on the pump.

P2 pressure adjusting screw

Note 1) Many other variable control mechanism are also available in addition to those in the above table. Please consult your agent for details. Note 2) We recommend ZR-T02-*-5895* as the remote control valve. For details, consult your agent. Prevent the pipe volume up to the remote control valve from falling below 150cm3.

A-5

Pressure Compensation Type

Manual mode: standard type

A
Piston Pumps

PVS-0B-8N*-30

Installation Dimension Drawing


Pressure compensator 47 29 3 Lubrication port 6

Pump capacity q cm3/rev

214( MAX) 164.5(MAX) Drain port (flow rateadjustmentlength) Rc3/8 10 5 Lock nut Lock nut

49.5 18 14 MIN 6 Pressure adjusting screw

Relationship between flow rateadjustment length ( ) and pump capacity (q)


10 8

Key width 4.76 Flow rate adjusting screw 42.5 25.4 5


0 19.05 0.021 0 21.2 0.25 f 82.6 0.036 0.071

0 0.012

cm3/rev

PV
4 3 2 5

78

142

11

77

S-

8N B-

*-3

132

Flow rate adjustment range


10 15

Discharge port G(Former PF)1/2 11 127.5 149.5

49

R4 6

Flow rate adjustment length mm


53.2 Discharge port G(Former PF)1/2 106.4 110 130 Suction port G(Former PF)3/4

Set a flow rate adjustment length within the above range. Oil will leak if the pump is operated below the adjustment range lower limit.

Cross-sectional Drawing

Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Part Name Body Case Shaft Cylinder barrel Valve plate Piston Shoe Shoe holder Barrel holder Swash plate Thrust bush Spring holder Gasket Spring C

Part No. 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Part Name Spring S Control piston Guide pin Parallel key Retainer Needle Ball bearing Needle bearing Oil seal Snap ring Snap ring Snap ring O-ring O-ring

Part No. 29 30 31 32 33 34 35 36 37 38 39 40

Part Name Parallel pin Spring pin Hexagon socket head bolt Cross-recessed countersunk head screw Hexagon socket set screw Hexagon nut Hexagon plug Metal plug Nameplate Lubrication port plate CAUTION plate Rivet

List of Sealing Parts


Part No. 13 23 27 28 Part Name Packing Oil seal O-ring O-ring Q'ty 1 1 1 1 PVS-0B-8 Size PS46-100000 TCV-254511 1B-P9 1B-P11 Remarks 3 Bond N.O.K JIS B 2401 JIS B 2401

Performance Curves
General Performance
Discharge volume Q liter/min Discharge volume Q 1800min1 Volume efficiency v 15 14 13 12

Parts marked by an asterisk "*" are not available on the market. Consult your agent.

Typical characteristics at hydraulic operating fluid kinematic viscosity of 32 mm2/s

Discharge volume Q liter/min

Pressure - Discharge Volume Characteristics


Discharge volum eQ 1800min1 1500min1
7 6 5 4 3 2 1 0 0

Axial Input

14 12

Efficiency ,v%

Drain volume DR liter/min

Input Lin kW

Input Lin

4 2 0

4 2 0 0

in 0m 180

150

0min

4 2 0

Drain volume DR
7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Input Lin kW

100 90 80 70 60 50

Overall efficiency
in 0m 180 1 n 0mi 150 1

6
Input Lin

Axial Input kW

1500min1

Q=14.4 r/min Q=12 r/min Q=10 r/min Q=8 r/min Q=6 r/min

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Axial Input at Full Cutoff


2.0 Axial input at full cutoff kW 1.5 1.0 0.5 0 0 Noise level dB(A) 80

Noise Characteristics
Measurement position: 1m rear of pump

70

1800

min

1500m

in

7 14 21 {71.4} {143} {214} Full cutoff pressure MPa {kgf/cm2}

in 00m 0/18 150 60 1 in 1800m 1 in 1500m At full cutoff 50 0 7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

A-6

Installation Dimension Drawing


PVS-1B-16 N*-(Z)-12 22 (side port type)
Flow rate adjustment length r Flow rate adjusting screw 236.5(MAX) 77 Drain port Rc3/8 23 Pressure adjusting screw (MIN)

A
Relationship between flow rate adjustment length (r) and pump capacity (q)
3 49.5 6

Piston Pumps

30
42 Lubrication port

Flow rate adjustment range Pump capacity q cm3/rev 22 20 16.5 10 7 5 Flow rate adjustment range 0 5 10 15 20
-1 2 B2N

43 25.4 47.50.2
NACHI

88 73

Key width 0 4.76 0.012 5

5.5

S PV

4-M10X16

220.2 158 181

12.5

0 19.05 0.021 0 21.2 0.25

24

2 *-1 6N B-1 S-1 PV

*-1

82 106.4 124 130 52 137 Suction port SAEJ518b-1

82.6 0.036 0.071

Discharge port SAEJ518b-3/4

11

Flow rate adjustment lengthr mm


Set a flow rate adjustment length within the above range. Oil will leak if the pump is operated below the adjustment range lower limit.

(axial port type)


236.5(MAX) Flow rate adjustment length r Flow rate adjusting screw 77 23(MIN) Drain port Rc3/8
Pressure adjusting screw

49.5 6 3 82 11 106.4 130 52 Pressure compensator 42 Lubrication port

120

42.5

Key width 0 4.76 0.012 5 88 73

55

25.4

12.5 183

4-M10X16

26.20.2 30 110

220.2 30

4-M10X16

Cross-sectional Drawing
Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Part Name Body Case Shaft Cylinder barrel Valve plate Piston Shoe Shoe holder Barrel holder Swash plate Thrust bush Seal holder Gasket Spring C Spring S Control piston Needle Key Nut Retainer Plug Part No. 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Part Name Ball bearing Needle bearing Oil seal Snap ring Snap ring Snap ring O-ring O-ring O-ring Pin Hexagon socket head bolt Cross-recessed countersunk head screw Hexagon socket set screw Metal plug Nameplate CAUTION plate Spring holder Lubrication port plate Rivet Guide pin

List of Sealing Parts


Part No. 13 24 28 29 30 Name Gasket Oil seal O-ring O-ring O-ring Q'ty 1 1 1 1 1 Size Remarks Nihon Gasket N.O.K JIS B 2401 JIS B 2401 JIS B 2401

0 19.05 0.021 0 21.2 0.25

SAE J518b-1 (suction port 24 mm dia.)

SAE J518b-3/4 (discharge port 24 mm dia.)

82.6 0.036 0.071

52.40.2

47.50.2

*
TCN-254511 1B-G55 1B-P9 1B-P14

Parts marked by an asterisk "*" are not available on the market. Consult your agent.

A-7

137

NACHI

Performance Curves

Typical characteristics at hydraulic operating fluid kinematic viscosity of 32 mm2/s

A
Piston Pumps

PVS-1B-16 N*(Z)-12
Discharge volume Q r/min Discharge volume Q r/min

General Performance
Discharge volume Q 1800min1 30 28 26 24 22

30 28 24

Pressure - Discharge Volume Characteristics


Discharge 1800min1 volume Q Axial input kW 14 12 10 8 6 4 2 0 0

Axial Input

Drain volume DR r/min

Input Lin kW

Input Lin

4
18

in 00m

150

0min

8 4 0

Input Lin kW

100 90 80 70 60 50 40

Volume efficiency v

1500min1

1500min1

Q=30 Q=25 Q=20 Q=15 Q=10

r/min r/min r/min r/min r/min

Efficiency ,v%

Overall efficiency

in 0m 180 1 n 0mi 150

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

12 10 8 6 4 2 0

Input Lin

12

2 0 0

Drain volume DR
7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Axial Input at Full Cutoff


Axial input at full cutoff kW 2.0 Noise level dB(A) 1.5 1.0 0.5 0 0 80

Noise Characteristics
Measurement position: 1m rear of pump

Oil Temperature Rise Characteristics PVS-1B-16N1-12


30 Revolution speed 1800 min1 Temperature difference

70

in 800m

in 1500m

min 1800 1 in 1500m

20 10 0

60 At full cutoff

Full cutoff pressure 7MPa Full cutoff pressure 3.5MPa Tank capacity 40

7 14 21 {71.4} {143} {214} Full cutoff pressure MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

4 5 Time Hr

30

Revolution speed 1800 min1

Performance Curves
PVS-1B-22N*-(Z)-12 General Performance
Discharge volume Q liter/min
Discharge 1 volume Q 1800min

Typical characteristics at hydraulic operating fluid kinematic viscosity of 32 mm2/s

Temperature difference

20 10 0

Full cutoff pressure 7MPa Full cutoff pressure 3.5MPa Tank capacity 60

1500min1 100 90 80 70 60 50 Efficiency ,v% Volume efficiency v Overall efficiency


1

40 35 30 25

Discharge volume Q liter/min

Pressure - Flow Rate Characteristics


40 30 Discharge volume Q 1800min1 1500min1

4 5 Time Hr

16 14 12 in 0m 0 10 18 1 8 n Input Lin mi 6 00 15 4 2 21 0 0 7 14 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Input Lin
1 m 800 in
1

Input Lin kW

12
1

Drain volume DR liter/min

4 2 00

15

in 00m

8 4

Drain volume DR

0 7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Input Lin kW

16

Axial Input
16 Q=40 14 Axial input kW 12 10 8 6 4
r/min

Axial input at full cutoff kW


Axial input at full cutoff kW 2.0 Noise level dB(A) 1.5 1.0 0.5 0 0 80 70 60 50 7 14 21 {71.4} {214} {143} Discharge pressure P MPa {kgf/cm2}

Noise Characteristics
Measurement position: 1m rear of pump

Q=35
r/min

Q=30
r/min

1800

min

min 1800 1 in 1500m

Q=25
r/min

Q=20
r/min

1500m

in

At full cutoff 0

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

2 00 7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

A-8

Installation Dimension Drawing


PVS-2B- 35 N*-(Z)-12(20) 45 (side port type)
317 (MAX) Flow rate adjustment length Flow rate adjusting screw
r

Relationship between flow rate adjustment length (r) and pump capacity (q)
3
Pressure adjusting screw

A
Piston Pumps

Lock nut

Drain port Rc1/2

Pressure compensator

45

60 MIN

6 Key width 6.3 +0.015 0.010 53 38

Pump capacity q cm3/rev

88

60

Lubrication port

50 45 40 35 30 20 11 10 8 0 20

Flow rate adjustment range


) 20 2( *-1 N 45 B-12 -2 N* S -35 PV 2B SPV

69.5

3 101.6 0.051
0

104 65 172 13

52.40.2

NACHI

28 A B

Flow rate adjustment range 25 30 35

4-M10X16

26.20.2 192 222

15

Discharge port SAEJ518b-1


A
0 22.23 0.021 24.9 0

144 146 172

Suction port SAEJ518b-11/4

Flow rate adjustment lengthr mm


Set a flow rate adjustment length within the above range. Oil will leak if the pump is operated below the adjustment range lower limit.

Pressure cm3/rev Range Design No.

B
0 0.5 0

35 45

0 to 3 0 to 2 12D 3 20D

25.385 0.025 27.850.25

(axial port type)


128 Flow rate adjustment length Flow rate adjusting screw r Lock nut

257 (MAX) Drain port Rc1/2 88 60(MIN)


Pressure adjusting screw

60 6

Pressure compensator

45

Key width +0.015 6.3 0.010 53 38 NACHI 104

69.5

101.6 0.051

3 65

Lubrication port

58.70.2

SAE J518b-11/4 (suction port 28 mm dia.) 4-M10X16 30.20.2 37 140 26.20.2 37

52.40.2

SAE J518b-1 (discharge port 28 mm dia.) 15 4-M10X16


Range

A B

220
cm3/rev Pressure Design
No.

146 172

A 22.23
0 0.021

B 24.9
0 0.5

35 45

0 to 3 12D 0 to 2 3 20D

Part No.

Part Name Body Case Shaft Cylinder barrel Valve plate Piston Shoe Shoe holder Barrel holder Swash plate Thrust bush Seal holder Gasket Spring C Spring S

Part No.

Part Name Control piston Needle Key Nut Retainer Plug Ball bearing Needle bearing Oil seal Snap ring Snap ring Snap ring O-ring O-ring O-ring

Part No.

172

13

Part Name Backup ring Pin Hexagon socket head bolt Cross-recessed countersunk head screw Flow rate adjusting screw Metal plug Nameplate CAUTION plate Spring holder Guide Lubrication port plate Orifice Rivet

0 0 25.385 0.025 27.850.25

Cross-sectional Drawing
PVS-2B- 35 N*-(Z)-12 45

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

31 32 33 34 35 36 37 38 39 40 41 42 43

List of Sealing Parts


Part No. 13 24 28 29 30 31 Part Name Gasket Oil seal O-ring O-ring O-ring Backup ring Q'ty 1 1 1 1 1 1 PVS-2B-35/45 Size * TCN-305011Z 1B-G70 1B-P14 1B-P11 T2-P11 Remarks Nihon Gasket N.O.K JIS B 2401 JIS B 2401 JIS B 2401 JIS B 2407

Parts marked by an asterisk "*" are not available on the market. Consult your agent.

Part No.

Part Name Body Case Shaft Cylinder barrel Valve plate Piston Shoe Shoe holder Barrel holder Swash plate Thrust bush Seal holder Gasket Spring C Spring S Control piston

Part No.

Part Name Needle Key Nut Retainer Plug Roller bearing Needle bearing Oil seal Snap ring Snap ring Snap ring O-ring O-ring O-ring Backup ring Pin

Part No.

Part Name Hexagon socket head bolt Cross-recessed countersunk head screw Flow rate adjusting screw Metal plug Nameplate CAUTION plate Spring holder Guide Lubrication port plate Orifice Rivet Orifice Pin O-ring Plug

PVS-2B-45N3-(Z)-20

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

List of Sealing Parts


Part No. 13 24 28 29 30 46 31 Part Name Gasket Oil seal O-ring O-ring O-ring O-ring Backup ring Q'ty 1 1 1 1 1 2 1 1B-G70 1B-P14 1B-P11 1B-P5 T2-P11 Size * TCN-305011Z

PVS-2B-45N3 Remarks Nihon Gasket N.O.K JIS B 2401 JIS B 2401 JIS B 2401 JIS B 2401 JIS B 2407

Parts marked by an asterisk "*" are not available on the market. Consult your agent.

A-9

Performance Curves

Typical characteristics at hydraulic operating fluid kinematic viscosity of 32 mm2/s

A
Piston Pumps

PVS-2B-35N*-(Z)-12 General Performance


Discharge volume Q r/min Discharge volume Q 1800min1 65 60 55 50 Discharge volume Q r/min 70 60 50

Pressure - Discharge Volume Characteristics


Discharge volume Q 1800min1 Axial input kW 28 24 20 16 12 8 4 0 0

Axial Input

Q=60
r/min

1500min1
100 90 80 70 60 50 Volume efficiency v Overall efficiency
1

Q=50
r/min

Efficiency ,v%

1500min1

Q=40
r/min

30 Drain volume DR r/min 20 10 0 Input Lin kW Input Lin 4 2 0 0


in 0m 180 1 0min 150
1

30 20 Input Lin kW

Q=30
r/min

Input Lin

180

n 0mi

150

0min

Drain volume DR

10 0

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

7 14 21 {214} {71.4} {143} Discharge pressure P MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

Axial Input at Full Cutoff


Axial input at full cutoff kW 4 3 2 1 0 0
1800 min
1

Noise Characteristics
Noise level dB(A) 80 70 60 50
Measurement position: 1m rear of pump

15

00min

1800min 1 1500min At full cutoff


0

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Full cutoff pressure MPa {kgf/cm2}

Performance Curves
PVS-2B-45N*-(Z)-12(20) General Performance
Discharge volume Q liter/min

Typical characteristics at hydraulic operating fluid kinematic viscosity of 32 mm2/s

Discharge volume Q liter/min

Discharge 1800min1 volume Q 1500min1 100 90 80 70 60 50 Efficiency ,v% Volume efficiency v Overall efficiency

80 75 70 65

Pressure - Discharge Volume Characteristics


80 70 60 Input Lin Discharge volume Q
1800min1 1500min 1

Axial Input
32 28 Axial input kW 24 20 16 12 8 4 00 7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2} Q=80
r/min

Q=70
r/min

Q=60
r/min

Q=50
r/min

Input Lin kW

Q=40
r/min

30 Input Lin
in 0m 180 1 n 0mi 150
1

20 10

Drain volume DR liter/min

4 2 00

min 500

20 10

0 7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2} 0

Drain volume DR

0 14 21 7 {214} {71.4} {143} Discharge pressure P MPa {kgf/cm2}

Axial Input at Full Cutoff


Axial input at full cutoff kW 4 3 2 1 0 0
1

Noise Characteristics
80 Noise level dB(A) 70 60 50
Measurement position: 1m rear of pump

in 1800m

in1 1800m in1 1500m


At full cutoff 0

1500min

21 7 14 {71.4} {143} {214} Full cutoff pressure MPa {kgf/cm2}

7 14 21 {71.4} {143} {214} Discharge pressure P MPa {kgf/cm2}

A-10

Input Lin kW

in 0m 180

30

Response Performance

A
Test Circuit
Piping volume 400 cm3

Pressure MPa

Piston Pumps

t1 t2

Q
Legend

Ps FC (Q=0) 14MPa 1MPa

MPa

M
M 0

1MPa

(Q=MAX) SOL ON

SOL OFF
Time s

SOL OFF

Response Time (s) Model No. t1 PVS-0B-8 PVS-1B-16 PVS-1B-22 PVS-2B-35 PVS-2B-45 0.03 to 0.04 0.05 to 0.06 0.05 to 0.06 0.05 to 0.06 0.05 to 0.06 t2 0.04 to 0.06 0.07 to 0.08 0.07 to 0.08 0.05 to 0.07 0.05 to 0.07

Surge Pressure MPa{kgf/cm2} PS 12 to 4{20.4 to 40.8} 14 to 7{40.8 to 71.4} 15 to 8{51 to 81.6} 16 to 9{61.2 to 91.8} 16 to 9{61.2 to 91.8}

Response performance changes according to pipe volume and size. Use an anti-surging valve to prevent surge voltage.

Pressure Compensator
Part No. 1 2 3 4 5 6 7 Part Name Body Spool Holder Plunger Spring Retainer Pressure adjusting bolt Part No. 8 9 10 11 12 13 14 Part Name Nut O-ring O-ring O-ring Plug Plug Mounting bolt

List of Sealing Parts


Part No. 9 10 11 Name O-ring O-ring O-ring Q'ty 1 3 1 Size For 0B, 1B, 2B 1A-P14 1B-P6 1B-P10

Note) O-ring 1A/B-** refers to JIS B2401-1A/B.

A-11

Pressure Compensation Type

(remote control mode) P-Q Characteristics


Max. pump capacity q cm3/rev
77 6 60 42 49 132 11

A
Piston Pumps

Explanation of model No.: PVS 0 B 8 P * 30


Design No. 30: PVS-0* 12: PVS-1*, PVS-2* 20: PVS-2*-45P3 only Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} P: Pressure compensation type (remote control mode) Max. pump capacity (cm3/rev) Nominal 8, 16, 22, 35, 45 Pump size 0, 1, 2

Set by remote control V

Discharge pressure P MPa

Installation Dimension Drawing


PVS-0B-8P*-30
214(MAX) 164.5(MAX) 93.5 (flow rate adjustr ment length) Pilot port 5 Rc1/4 49.5 6 Drain port Rc3/8

18

10 Lock nut Flow rate adjusting screw

47 29

3 Lubrication port

Key width 0 4.760.012 142 42.5 25.4 5 78

82.6 0.036 0.071

R46

Discharge port G(Former PF)1/2 11 127.5 149.5


0 19.05 0.021 0 0.25

53.2 Discharge port G(Former PF)1/2 106.4 110 130

PVS-1B- 16P*-12 22
236(MAX) Pilot port Rc1/4 77 49.5 Drain port Rc3/8 Differential pressure adjusting screw (adjustment forbidden) 6 43 25.4 47.50.2 Key width 0 4.76 0.012 5

Flow rate adjustr ment length Flow rate adjusting screw

21.2

Suction port G(Former PF)3/2

Lubrication port 3 82 106.4 124 130 52 Suction port SAEJ518b-1

55

88 73

82.6 0.036 0.071

24

4M10x16

220.2 158 181

12.5

19.05 0.021

21.2

0 0.25

Discharge port SAEJ518b-3/4

PVS-2B- 35P*-12(20) 45
Flow rate adjustment length r 317(MAX) Drain port Rc1/2 Pilot port pp Flow rate adjusting screw Rc1/4 Lock nut Differential pressure adjusting screw (adjustment forbidden) 88 60 6 Key width +0.015 6.3 0.010 69.5 53 38 52.40.2
NACHI

11

0 0.051

28

101.6

A B

4M10x16

26.20.2 192 222

15

Discharge port SAEJ518b-1

144 146 172

cm3 /rev Pressure Design A Range No. 35 0 to 3 12D 22.23 0 to 2 45 3 20D 25.385

B
0 0.021 0 0.025

24.9

0 0.5 0

27.85 0.25

A-12

65 Suction port SAEJ518b-11/4

172

13

104

45

Lubrication port

137

NACHI

2-pressure, 2-flow Rate Control Type


Explanation of model No.: PVS 1 B 16 N 3 Q 1 12
Design No. 12: PVS-1*, PVS-2* 20: PVS-2*-45N3Q* Pressure adjustment range N*: High-pressure adjustment range, P2 Q*: Low-pressure adjustment range, P1 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} NQ: 2-pressure, 2-flow rate control Max. pump capacity (cm3/rev) Pump size 1, 2 Nominal 16, 22, 35, 45

A
Piston Pumps

Installation Dimension Drawing


PVS-1B- 16N*Q*-12 22

296(MAX) Drain port Rc3/8 77 P2 pressure adjusting screw 23 (MIN) 3 49.5 6 Pressure compensator 42 Lubrication port

P-Q Characteristics
q1

43

Key width 88
0 4.76 0.012

P1 pressure adjusting screw 73 82

25.4 47.50.2 q1 flow rate adjusting screw q2 flow rate adjusting screw

5
82.6 0.071
0.036

Pump capacity q cm3/rev (Note 2) Pump capacity q cm3/rev (Note 2)


172 3 13 104 Suction port SAEJ518b-11/4

24

11

137

19.05 0.021

4M10x16

220.2 158 181

12.5

21.2 0.25

107.5(MAX) Discharge port SAEJ518b-3/4 106.4 124 130 Suction port SAEJ518b-1

52

NACHI

q2

P1 P2 Discharge pressure P MPa

PVS-2B- 35N*Q*-12(20) 45

P-Q Characteristics
q1

352(MAX) Drain port Rc1/2 88 P2 pressure adjusting screw 60(Min) 60 Pressure compensator 6 Key width +0.015 6.3 0.010 q1 flow rate adjusting screw q2 flow rate adjusting screw 52.40.2
28
NACHI

45

Lubrication port

P1 pressure adjusting screw

q2

101.6 0.051

53 38

0
65

P1 P2 Discharge pressure P MPa

4M10x16 26.20.2 192 222 15

A B

Discharge port SAEJ518b-1 144 146 172

107.5(MAX)

cm3/rev Pressure Design A B Range No. 0 0 35 0 to 3 22.23 0.021 24.9 0.5 0 to 2 12D 45 0 0 3 20D 25.385 0.025 27.85 0.25

Pump Model No. PVS-1B-16 PVS-1B-22 PVS-2B-35 PVS-2B-45

q2 Adjustment Range (cm3/rev) 0 to 10 0 to 13 0 to 19 0 to 24

Default q2 (Setting cm3/rev) 3.3 4.4 7 9

Note 1) The setting range of maximum pump capacity q1 varies according to the setting of q2. Note 2) Overall efficiency at a low flow rate is worse than at the maximum flow rate. Pay attention to this when selecting the motor capacity for the drive.

A-13

Solenoid Cutoff Control Type

A
Piston Pumps

Explanation of model No.: PVS 1 B 16 R 2 S 1 12


Solenoid power supply 1: AC100V 2: AC200V 3: DC12V 4: DC24V Solenoid specifications A: SA-G01 S: SS-G01 Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} R A : Solenoid cutoff control S Max. pump capacity (cm3/rev) Nominal 16, 22, 35, 45 Pump size 1, 2

P-Q Characteristics
Pump capacity q cm3/rev

SOL "OFF"

SOL "ON"

Discharge pressure P MPa

Installation Dimension Drawing


PVS-1B- 16R*A*-12 22 S
199.8 42

SOL b Pressure adjusting screw (at solenoid ON) Drain port Rc3/8 77 47.4 49.5 6 108 43 25.4 47.50.2
NACHI

Differential pressure adjusting screw (adjustment forbidden) Lubrication port 177(SA-G01) 215(SS-G01)
194.5(SA-G01) 236(SS-G01) 172 Suction port SAEJ518b-11/4 65 Discharge port SAEJ518b-1 144 146 172

Flow rate adjusting screw

55

Key width 0 4.76 0.012 5

82 106.4 124 130 45


Differential pressure adjusting screw (adjustment forbidden) Lubrication port 3 104 13

3 52 137

19.05 0.021

4M10x16

220.2 158 181

12.5

21.2

0 0.25

82.6 0.071

0.036

Discharge port SAEJ518b-3/4

11

Suction port SAEJ518b-1

PVS-2B- 35R*A*-12(20) 45 S
317(MAX) Pilot port Rc1/4 Drain port Rc1/2 Differential pressure adjusting screw (adjustment forbidden) 88 60 6 Key width +0.015 6.3 0.010 53 38 52.40.2
NACHI

Pressure adjusting screw (at solenoid ON) Lock nut Flow rate adjusting screw

SOL b

69.5

28

26.20.2 192 222

15

cm3 /rev Pressure Design Range No. 0 to 3 35 45

A B

4M10x16

101.6

0 0.051

A
0

B
0

22.23 0.021 24.9 0.5 0 to 2 12D 0 0 3 20D 25.385 0.025 27.850.25

The coil surface temperature increases if this pump is kept continuously energized. Do not touch the surface of the coil directly with your hands.

A-14

90.5

2-pressure Control Type


Explanation of model No.: PVS 1 B 16 W 2 S 1 12
Solenoid power supply 1: AC100V 2: AC200V 3: DC12V 4: DC24V Solenoid specifications A: SA-G01 S: SS-G01 Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} W A : 2-pressure control S Max. pump capacity (cm3/rev) Nominal 16, 22, 35, 45 Pump size 1, 2

P-Q Characteristics
Pump capacity q cm3/rev

A
Piston Pumps

SOL "OFF"

SOL "ON"

P2 P1 Discharge pressure P MPa

Installation Dimension Drawing


PVS-1B- 16 W*A*-12 22 S
42

Pressure adjusting screw (at solenoid OFF)

SOL b

Drain port Rc 3/8 Pressure adjusting screw (at solenoid ON)

Differential pressure adjusting screw (adjustment forbidden) 195(SA-G01) 233(SS-G01) 137 106.4 124 130
Differential pressure adjusting screw (adjustment forbidden) 212.5(SA-G01) 254(SS-G01) 172 65 144 146 172 13 SAEJ518b-11/4

Lubrication port

Flow rate adjusting screw

77

49.5 6 43 25.4 Key width 0 4.76 0.012 5 127

55

82.60.036 0.071

47.50.2

11

4M10x16

158 181

220.2

12.5

19.050.021 0 21.2 0.25

Discharge port SAEJ518b-3/4

PVS-2B- 35 W*A*-12(20) 45 S
317 (MAX ) Pilot port pp Rc 1/4 Drain port Rc 1/2 Pressure adjusting screw (at solenoid ON) Differential pressure adjusting screw (adjustment forbidden) 88 Flow rate adjusting screw 60 6 Key width +0.015 6.3 0.010 45

Pressure adjusting screw (at solenoid OFF) Lock nut

SOL b

69.5

52.40.2

4M10x16 26.20.2 192 222 15

A B

101.6

0 0.051

53 38
NACHI

Discharge port
SAEJ518b-1

90.5

Suction port

cm3/rev Pressure Design A B Range No. 0 0 35 0 to 3 12D 22.23 0.021 24.9 0.5 0 to 2 45 0 0 3 20D 25.385 0.025 27.85 0.25

The coil surface temperature increases if this pump is kept continuously energized. Do not touch the surface of the coil directly with your hands.

104

Lubrication port

52 Suction port SAEJ518b-1

82

NACHI

A-15

2-pressure, 2-flow rate Control Type w/ Solenoid Cutoff


Pump capacity q cm3/rev

A
Hydraulic Pumps

Explanation of model No.: PVS 1 B 16 RQ 2 S 1 12


Solenoid power supply 1: AC100V 2: AC200V 3: DC12V 4: DC24V Solenoid specifications A: SA-G01 S: SS-G01 Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} A : 2-pressure, 2-flow rate control w/ RQ S solenoid cutoff Max. pump capacity (cm3/rev) Nominal 16, 22, 35, 45 Pump size 1, 2

P-Q Characteristics

SOL "ON"

SOL "OFF" Discharge pressure P MPa

Installation Dimension Drawing


PVS-1B- 16RQ*A*-12 22 S
296(MAX) 42

P2 pressure adjusting screw (at solenoid ON) 177(SA-G01) 215(SS-G01) q1 flow rate adjusting screw q2 flow rate adjusting screw
SOL b

Drain port Rc 3/8 77 23 49.5 6 43 25.4 Key width 0 4.76 0.012 5

Differential pressure adjusting screw (adjustment forbidden) Lubrication port 3 82


172 107.5(MAX) Discharge port SAEJ518b-1 cm3/rev Pressure Design A B Range No. 0 0 35 0 3 12D 22.23 0.021 24.9 0.5 0 2 45 0 0 3 20D 25.385 0.025 27.85 0.25 144 146 172 Suction port SAEJ518b-11/4 65 194.5(SA-G01) 236(SS-G01)

P1 pressure adjusting screw

11

82.6 0.036 0.071

47.50.2

19.050.021

4M10x16

220.2 158 181 221

12.5

21.2 0.25

Discharge port SAEJ518b-3/4

107.5(MAX) 106.4 124 130

Suction port SAEJ518b-1

PVS-2B- 35RQ*A*-12(20) 45 S
352(MAX) Drain port Rc 1/2 Pressure adjusting screw (at solenoid ON) q1 flow rate adjusting screw q2 flow rate adjusting screw 45

SOL b

Differential pressure adjusting screw (adjustment forbidden)

88
6

Key width +0.015 6.3 0.010 53 38 52.40.2


8 2
NACHI

P1 pressure adjusting screw 90.5 104

0 0.051

4M10x16

26.20.2 192 222

15

The coil surface temperature increases if this pump is kept continuously energized. Do not touch the surface of the coil directly with your hands.

A-16

A B

101.6

13

60

Lubrication port

52

137

NACHI

2-cutoff Control Type


Explanation of model No.: PVS 1 B 16 C 2 S 1 12
Solenoid power supply 1: AC100V 2: AC200V 3: DC12V 4: DC24V Solenoid specifications A: SA-G01 S: SS-G01 Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} 3: 3-21MPa {30.6-214kgf/cm2} C A : 2-cutoff control S Max. pump capacity (cm3/rev) Nominal 16, 22, 35, 45 Pump size 1, 2

P-Q Characteristics
Pump capacity q cm3/rev

A
Hydraulic Pumps

SOL "ON" SOL "OFF" Discharge pressure P MPa

Installation Dimension Drawing


PVS-1B- 16 C*A*-12 22 S

296(MAX) q1 flow rate adjusting screw Drain port q2 flow rate adjusting screw Rc 3/8 77

49.5 6 80 3 82 11 102 Discharge port SAEJ518b-3/4 106.4 124 130 Suction port
SAEJ518b-11/4

Differential pressure adjusting screw (adjustment forbidden) 43 25.4


NACHI

42

Lubrication port

88

Key width 0 4.76 0.012

P1 pressure adjusting screw

24

82.6 0.036 0.071

47.50.2

0 19.050.021

220.2 25 295(SA-G01) 331(SS-G01) 158 181

12.5

4M10x16

PVS-2B- 35C*A*-12(20) 45 S

352(MAX) q1 flow rate adjusting screw q2 flow rate adjusting screw 88 Drain port Rc 1/2

60 6

21.2 0.25

Lubrication port

Key width 6.3 +0.015 0.010 53 38 52.40.2


2
8
NACHI

P1 pressure adjusting screw 90.5 104

0 101.6 0.051

13

A B

4M10x16

26.20.2 192 222 351(SA-G01) 387(SS-G01)

15

Discharge port SAEJ518b-1 144 146 172


cm3/rev Pressure Design A B Range No. 0 0 35 0 3 12D 22.23 0.021 24.9 0.5 0 2 45 0 0 3 20D 25.385 0.025 27.85 0.25

102

Suction port SAEJ518b-11/4

The coil surface temperature increases if this pump is kept continuously energized. Do not touch the surface of the coil directly with your hands.

65

172

P2 pressure adjusting screw

Differential pressure adjusting screw (adjustment forbidden) 45

52

137

A-17

Foot Mounting Kit

A
Piston Pumps
Kit Model No. IHM-2-10 IHM-4-10 Applicable Pump Model No. PVS-0B PVS-1B PVS-2B Accessories Bolt TB-1030 TB-1230 Q'ty 2 2 Washer WP-10 WP-12 Dimensions H 96 140 (I) 64.5 56.7 (J) 32 44 K 17.5 16 N 13 16 P M10 M12 Q 135 195.5 (S) 32.5 12.7 T 36.5 53
D d1 d2 d3 d4

Dimensions Q'ty 2 2 A 127.7 220.7 B 152.5 246.5 C 69.8 107.95 E 1 1 F 150.8 114.3 Weight kg 2.0 5.5

Kit Model No. IHM-2-10 IHM-4-10

82.6 101.6

22 22

11 11

106.4 146

50 40

When only the mounting feet are required, the pump mounting bolts, washers and other parts are sold together as the Foot Mounting Kit.

Coupling kit
Kit for PVS-0B: PSCF-100000
Applicable Pump Model No. Plunger Kit model No. L L1
K D

PVS-0B-8 Suction port 46 16


36 16

Discharge port 40 14
27 12

H G screw size Rc screw size O-ring size

36 G3/4 Rc3/4 1B-P24

27 G 1/ 2 Rc1/2 1B-P18

Notes) 1. Joints are on sale in the Joint Kit which includes O-rings. 2. The dimensions of the O-ring seal section on the connector conforms with JIS B2351. 3. O-ring 1B/B-** refers to JIS B2401-1B.

Piping Flange Kit


For PVS-1B, 2B

Applicable Pump Model No. Plunger Kit model No. A B C D T


d1 d2

PVS-1B-16/22 PSF-101000 Suction port 70 59 52.4 26.2 24


11 28

PVS-2B-35/45 PSF-102000 Discharge port 65 52 47.5 22.0 24


11 22

Suction port 79 73 58.7 30.2 28


11 37

Discharge port 70 59 52.4 26.2 24


11 28

X Mounting bolt Washer O-ring Weight kga

1 TH-1040 WS-B-10 1B-G35 0.6

3/4 TH-1040 WS-B-10 1B-G30 0.5

1-1/4 TH-1045 WS-B-10 1B-G45 0.75

1 TH-1040 WS-B-10 1B-G35 0.6

Notes) 1. The piping flange is on sale in the Flange Kit which includes mounting bolts, washers and O-rings. 2. O-ring 1B/B-** refers to JIS B2401-1B. 3. For details on tightening torque, see page C-11.

A-18

To improve reliability, design Nos. 17 and 31 were adopted due to remodeling of the grease injection system connecting section.

Uni-pump Specifications
Explanation of model No.

A
Piston Pumps
17(31)
Design No. 17: PVS-1B 0.75-5.5kW PVS-2B 3.7 -7.5kW 31: PVS-0B 0.75-3.7kW Auxiliary symbol None: Side port type Z: Axial port type (PVS-1B, 2B) Number of motor poles 4: 4 poles Motor terminal None: Right side viewed from shaft end A: Left side viewed from shaft end

UPV 1 A 16 N 1 1.5

Motor output 0.7: 0.75kW 3.7: 3.7kW 1.5: 1.5 kW 5.5: 5.5kW 2.2: 2.2 kW 7.5: 7.5kW

0A Note) UPV- 1A is 0.75-5.5kW UPV-2A is 3.7-7.5kW

Pressure adjustment range 0: 2- 3.5MPa {20.4- 35.7kgf/cm2} 1: 2- 7MPa {20.4- 71.4kgf/cm2} 2: 3-14MPa {30.6-143kgf/cm2} (Note) Not available at 45 cm3/rev 3: 3-21MPa {30.6-214kgf/cm2} Variable control mechanism N: pressure compensation type Max. pump capacity (cm3/rev) Nominal 8, 16, 22, 35, 45 Motor mounting method Mounting foot type Pump size 0: PVS-0B, 1: PVS-1B, 2: PVS-2B PVS series uni-pump

Motor selection curves

UPV-0A
( /min) 16 Discharge volume Q 14 12 10 8 6 4 2 0 0.75kW 2 4 6 8 10 12 14 16 18 20 21 {20.4}{40.8}{61.2}{81.6} {102} {122} {143} {163} {184} {204} {214} Discharge pressure P MPa {kgf/cm2} 0 1.5kW 2.2kW 3.7kW Discharge volume Q ( /min) 40

UPV-1A
5.5kW 3.7kW 30 2.2kW 1.5kW 20 Discharge volume Q

UPV-2A
( /min) 80 7.5kW 5.5kW 60 3.7kW

40

10 0.75kW 2 4 6 8 10 12 14 16 18 20 21 {20.4}{40.8}{61.2}{81.6} {102} {122} {143} {163} {184} {204} {214} Discharge pressure P MPa {kgf/cm2}

20

2 4 6 8 10 12 14 16 18 20 21 {20.4}{40.8}{61.2}{81.6} {102} {122} {143} {163} {184} {204} {214} Discharge pressure P MPa {kgf/cm2}

How to select the motor The lower side of the output curves for each of the motors shown above indicates the operating range under rated output for that motor.

A-19

Installation Dimension Drawings

A
Piston Pumps

UPV-0A-8**-**-4-31 (side port type)


Drain port Rc 3/8 Lubrication port A terminal KL D KL B terminal
Flow rate adjusting screw

A terminal L

B terminal A Fan cover

164.5 (MAX) 18
Pressure adjusting screw

IL

77

(Round drain hole) 11 G Suction port G3/4 110 E M E J Discharge port G1/2 127.5 port position) 149.5
(suction port, discharge

KD

50

O F N

O F S

View R (4 locations)

UPV-1A- 16 **-**-4-17 22 (side port type)


D A terminal KL Lubrication port KL B terminal
Flow rate adjusting screw

187 (MAX) 77 Drain port Rc 3 /8

L IL
Pressure adjusting screw

A B terminal

A terminal

82

KD

4-M10X16 24 52.40.2

55 47.50.2

Pump model No. nameplate

4-M10X16 24

26.20.2 View R (4 locations)

Suction port shape

UPV-2A- 35**-**-4-17 45 (side port type)


D A terminal KL Lubrication port KL B terminal 257 (MAX)
Flow rate adjusting screw

L 77 IL
Pressure adjusting screw

Suction port S A E J5 1 8 b -1

124 E E

Discharge port SAE518b-3/4

2 2 0 .2

158 port position) 181

(suction port, discharge

O O F F N

A B terminal

Drain port Rc 1/2

A terminal

104

(Round drain hol)

KD

4-M10X16 28 26.20.2 58.70.2 192 port locations) 222


(suction port, discharge

Suction port SAEJ518b-1 1/4

144 E M E

69.5 52.40.2

Discharge port SAEJ518b-1

O O F N S

4-M10X16 28

30.20.2 Suction port shape

View R (4 locations)
Note: A terminal measurements are in parentheses ( ).

1. A class E totally enclosed fan-cooled type is used as the reference motor. 2. 200 V/220 V, 60 Hz and 200 V, 50 Hz are used as the reference motor voltages. 3. Viewed from the pump side, the suction port on the left side and the discharge port on the right side are used as the reference port locations. 4. Broken lines indicate instances for the A terminal. Broken lines pass through to the other side of the pump along its center.

A-20

Motor Specifications
Output kW 0.75 1.5 2.2 3.7 5.5 7.5 Motor Dimensions A 124 IL 107.5 C 80 - 00.5 90 - 00.5 100 - 00.5
0 - 0.5

D 160 178 195 219 276 276

E 62.5 70 80 95 108 108

F 50 62.5 70 70 70 70

G 10 10 13 14 16 16

H 160 179 197.5 221.5 270 270

I 311.5 311.5

J 34 35 45 45 50 50

L 231.5 261 296.5 314.5 380.5 380.5

M 155 170 195 224 250 250

N 135 155 175 175 175 175

ST 1025 1016 1225 1225 1225 1225

KD

KL 126 136 150 161 217 217

O 21 36.5 45.5 53 33.5 33.5

Frame Weight No. 80M 90L 100L 112M 132S 132S 12 16 20 29 48 54

A
Piston Pumps

22 22 22 22 34 34

142.5 118.5 160.5 171 217 217 136

143.5 112

163.5 132 - 00.5 163.5 132


0 - 0.5

A-21

You might also like