Professional Documents
Culture Documents
RXTUG 22H
1MRK 513 001-BEN
Page 1 Issued June 1999 Changed since July 1998 Data subject to change without notice
(SE970173)
Features
Input voltage 24 - 250 V dc Output voltage selectable 12, 18 or 24 V dc, normally factory setting 24 V dc Galvanically separated inputs and outputs Can be loaded with up to 20 W LED indicates proper in service operation
The output voltage is monitored and loss of voltage alarmed by a built-in auxiliary relay Protected against wrong polarity on the input voltage Can be connected in parallel to receive redundant voltage supply
Application
The RXTUG 22H is primarily intended for auxiliary voltage supply of electronic circuits. It is suitable for use when moderate output power is required, e.g. for the supply of protective relays or automatic equipment. The RXTUG 22H converts an incoming dc voltage to an ac voltage which is subsequently transformed, rectified and smoothed to another regulated and stabilized dc voltage. This converter has a high degree of efficiency and it can be loaded up to 20 W for 5 minutes and 15 W continuously. Unsymmetrical load of plus and minus U2 (see Fig. 1) can be accepted up to 100% of rated load. The input and output voltages of the converter are galvanically separated, which contributes to the suppression of any transients occurring in the input voltage. The input is supplied with a voltage polarizing protection to prevent damage in case of faulty connection.
Design
The output voltage is monitored by a built-in auxiliary relay. During normal operation a green LED at the front is lit. If the output is short-circuited the converter drops out. When the short-circuit is removed, the converter restarts automatically. Using two parallel converters to receive redundant voltage supplies, an external diode connection is needed for the secondary side, see Fig. 1. RTXE diodes acc. to 1MRK 513 004-BEN may be used. The RTXE diodes mount in the rear pockets of the terminal bases and therefore do not add to the space requirements.
RXTUG 22H
1MRK 513 001-BEN
Page 2
Design (contd)
RTXC branch connectors acc. to1MRK 513 003-BEN may be used for making easy connections of the wiring from the RTXEs. COMBIFLEX sockets are fitted to the wires from RTXE.
+ U2 0 U 2
U<
316 318
317
Fig. 1
Technical data
Table 1: Energizing quantities, rated values and limits
Nominal input voltage, U1 Nominal output voltage, U2 Max. load continuously 5 min Permitted variation in input voltage Start time Current spike at connection Max output voltage variation Voltage ripple and transients at the output Power dissipation at no load Maximum capacitive load Permitted ambient temperature 24-250 V dc 12 V dc, 18 V dc, 24 V dc (selectable) 15 W 20 W +20% to -20% of the input voltage, U1 < 1,0 s 2A 10% at nominal input voltage POUT = 2-15 W < 0,4 V p-p 1,7 W 1000 F -20C to +55 C
(96000145)
RXTUG 22H
1MRK 513 001-BEN
Page 3
Diagram
+ U1 116 118 117
U<
+ U 2 0 U2
(96000146)
316 318
Fig. 2
317
Terminal diagram
Ordering
Specify: Type RXTUG 22H Quantity Ordering No. 1MRK 000 592-A U2 (if other than 24 V dc)
References
Manufacturer
ABB Automation Products AB Substation Automation Division SE-721 59 Vsters Sweden Tel: +46 (0) 21 34 20 00 Fax: +46 (0) 21 14 69 18
RXTUG 22H
1MRK 513 001-BEN
Page 4