You are on page 1of 16

U S E R

M A N U A L

F200 ADSL USB MODEM

CONTENTS

1. 2. 2.1 2.2 2.3 3. 3.1 3.2 3.3 3.4 3.5 3.6 4.

Introduction Specifications ADSL Standards supported Supported Protocols Connections Hardware Installation Procedures Hardware Requirements Preparing your network information Configure the ISP parameters for your Windows XP Driver Installation on Windows XP Software Configuration Connection to the Internet Troubleshooting

4 4 4 4 5 5 5 5 6 7 8 11 13

1. Introduction
F200 ADSL USB modem is a high performance and high-speed device that provides a full rate ADSL modem with the superb reliability and is a complete solution for home and office. The F200 ADSL USB modem can have a maximum downstream data rate of up to 8Mbps and an upstream of up to 1Mbps. You can safely enjoy the new generation broadband Internet with the F200 ADSL USB modem. Included drivers for Win98/ ME/ 2000/ XP.

2. Specifications
2.1 ADSL Standards supported: Supports ITU-T G.992.1(G.DMT) and ANSI T1.413 Issue 2 Supports G.992.2 (G.LITE) Annex A & B 2.2 Supported Protocols: WAN PPP over ATM (PPPoA) VC MUX PPP over ATM (PPPoA) with LLC/SNAP PPP over Ethernet (PPPoE) with LLC/SNAP PPP over Ethernet (PPPoE) with VC MUX LAN Bridged Ethernet (IP over ATM) with LLC/SNAP Bridged Ethernet (IP over ATM) with VC MUX Routed IP over ATM with LLC/SNAP Classical IP over ATM This package includes: F200 USB modem 1 USB cable 1 RJ11 telephone cable 1 CD with drivers 1 users manual 4

2.3 Connections

USB Connects the USB cable from the USB port of the F200 modem to the USB port of the computer. LINE Connects the RJ11 telephone cable from the telephone line port of F200 modem to the telephone plug.. LED indications: POWER: After successfully installing the modem, the POWER LED light turns on. It will stay on every time you start your computer.

3. Hardware Installation Procedures


3.1 Hardware Requirements The following hardware is necessary to configure and use the F200: RJ-11 (ADSL Ready) telephone Line USB cable (Included in the package) 3.2 Preparing your network information To configure your ADSL modem smoothly, it is required that you contact your ISP (Internet Service Provider) and acquire the following information: Type of Mode Encapsulation used: a. PPPoE, PPPoA, IPoA, Bridged or Routed. DSL connection parameters: b. For PPPoE or PPPoA, refer to Table 3 and fill-in all values (provided by your ISP). During the driver installation, select WAN. c.For Bridged, Routed, or IPoA, refer to Table 4 and fill-in all values (provided by your ISP). During the driver installation, select LAN. 5

Table 3 WAN (PPPoE/PPPoA parameters)


PVC Settings Login Information Line Modulation Information VPI VCI Encapsulation (LLC VCMux) Username Password Automatic ITU G.dmt or G.lite preferred Automatic ANSI T1.413 i2 preferred ITU (G.dmt or G.lite) G.dmt G.lite Value

table 4 LAN (Bridged/Routed/IPoA parameters)


PVC Settings IP Information Information VPI VCI Encapsulation (LLC or VC Mux) IP Address Subnet Mask Gateway IP Address Preferred DNS address Alternate DNS address (If available) Automatic ITU G.dmt or G.lite preferred Automatic ANSI T1.413 i2 preferred ITU (G.dmt or G.lite) G.dmt G.lite Value

Line Modulation

3.3 Configure the ISP parameters for your Windows XP F200 is initially set to function on Annex B protocol (ADSL over ISDN). To install the F200 based on Annex A protocol ( ADSL over PSTN), follow the procedure below. NOTE: THE FOLLOWING PROCEDURES APPLY FOR PPPoA MODE..
Annex Driver Setup Protocol Encapsulation Modulation VPI VCI USERNAME PASSWORD Table 5 A WAN PPPoA VCMUX Automatic ITU G.dmt or G.lite preferred 8 35 test test_passw

3.4 Driver Installation on Windows XP


Step 1: Windows will detect the newly installed device and the screen below will appear after the F200 USB ADSL Modem is attached to the systems USB port. Select "Install from a specific Location", and click "NEXT".

Step 2: Select "Include this location in the search" and type d:\driver\Wan (where D:\ the CD-ROM) Note: If the protocol being used is Bridged, Routed or IpoA, then type d:\driver\Lan

Step 3: Click Continue Anyway. This window appears only on Windows XP.

Installation continues

Step 4: Click "Finish"

Step 5: Left click on 'My Computer' icon and click on 'Properties_ > _Device Manager' Double click on Network adapters and check to see for: 'Crypto F200 USB ADSL WAN adapter'

3.5 Software Configuration

Continue the setup process of the F200. Step 1: Double click on the Access Runner icon

Step 2: Initially there is no connection / synchronization with the ADSL line Attempting to Activate Line. Press ALT P on your keyboard

Step 3: Here you can see that the connection has not been established. Attempting to Activate Line. Click the Line Setup tab

Step 4: Initially it is set to Annex B (ADSL over ISDN) as shown on the bottom right. Note: If the line was ISDN, then we do not change it.

Step 5: Select Annex A (ADSL over POTS) (given that the line was PSTN). Click Apply. Note: Incase you take out the USB plug from your computer and plug it back to the USB port of the computer again (does not matter if its upon shut-down or while the computer is on), then the Annex selection will automatically be set to Annex B. To set it back to Annex A, please follow this procedure again. Select the Protocol Setup tab

Step 6: In the Virtual Path Identifier (VPI) selection, and under Virtual Circuit 0, the value is 0. and In the Virtual Circuit Identifier (VCI) selection, and under Virtual Circuit 0, the value is 35. 9

Step 7: For the example insert: VPI = 8 VCI = 35 Click Apply.

Step 8: For Encapsulation Mode select the connection protocol: PPP over ATM VCMUX (RFC2364) Click Apply Click on the General tab

Step 9: Under Line Status, the indication ADSL Connection Established, indicates that the connection / synchronization with the ADSL line has been done with success. Note: 1 to 2 minutes are required after you make the above configurations, in order for the F200 to be synchronized with the ADSL line.

Step 10: To see information regarding the connection, click the Physical Layer Statistics tab, and click OK.

10

Double click on the Access Runner icon ADSL Connection Established indicates that the connection / synchronization with the ADSL line has been done with success. Note: After power on the PC, it takes 1 to 2 minutes in order for the F200 to be synchronized with the ADSL line.

3.6 Connection to the Internet

Step 1: To connect to the Internet, double click on the Connect Access Runner DSL icon which is found on the Desktop

Step 2: Insert the "User Login & Password" that has been given to you by your ISP, click Dial to connect.

Step 3: Double click on the connection icon on the Windows toolbar.

11

Step 4: To ensure that the F200 has been successfully installed, under the General tab, check to see that Connected is indicated next to Status. You can also check your connection speed: Speed -> 448.0kbps.

Step 5: Under the Details tab, you can see various information regarding the connection. (i.e. Server Type, Server IP address etc.).

12

4. Troubleshooting
The POWER LED is not on Check to see that the connections between the USB port of the F200 and the USB port of your computer are plugged in correctly. Cannot access ISP If in PPPoA & PPPoE mode, check your login account and password for the remote server. Check your VPI/VCI value and encapsulation mode are the same as your ISP gave you. Try to dial the phone to check if the phone line to CO is good if telephone service is available. Note: Incase you take out the USB plug from your computer and plug it back to the USB port of the computer again (does not matter if its upon shut-down or while the computer is on), then the Annex selection will automatically be set to Annex B. To set it back to Annex A, please follow the procedure of Step 5 of 3.5 Software Configuration. Reset (reset connection) Restart the connection of the F200 modem by pressing Stop and Start in the first window example of section 3.5. Note: Check to see if it is successful or not.

13

Declaration of Conformity
The 'F200 ADSL USB MODEM' is approved for use for within the European Union, and the compatibility of this unit and its basic requirements are declared with the CE symbol. Passage extract of the authentic declaration of conformity: CE Verification of Compliance Technical Standards: EMC: ETSI EN 300 386 v1.3.2/2002.12 LVD: EC LOW VOLTAGE DIRECTIVE 73/23/EEC, 93/68/EEC Measurement standards: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) EN EN EN EN EN EN EN EN EN EN 55022 : 1998 61000-3-2: 2000 61000-3-3: 1995 61000-4-2: 1998 61000-4-3: 1998 61000-4-4: 1995 61000-4-5: 1995 61000-4-6: 1996 61000-4-11: 1994 60950 : 2000

Measurement Facilities: BEST LABORATORY CO., LTD.

Note: Specifications are subject to change without prior notice.

www.crypto.gr

You might also like