You are on page 1of 2

Krupp Uhde

Mechanical Design Calculations MDC NO- 631

Code
QAFCO-4 Expansion Project
UAN (For QHMA)

Page of

01-3030

Calculations for Adequacy of Thread Engagement Nozzle Mark Type of Nozzle Design Pressure Design Temperature Corrosion Allowance Flange Material Allowable Stress at Design Temperature Allowable Stress at Atmosphere Temperature Joint Efficiency Stud Material Allowable Stress at Design Temperature Allowable Stress at Atmosphere Temperature Size of Stud Length of Hole for Stud (Page-67 of Dennis Moss) Minimum Length of engagement of threads LL = 0.75 x Db x Fbo / Ffo ___________(As per UG-43g) Larger of LL & Db Provided Length of Engagement of threads Lmin [ Lp [ in in. ] ] 0.750 0.760 P t ci Ffo Ffa E Fbo Fba Db Lb LL
[ 2 2

[ [
[ [ [

--2

] ]
] ] ] ]
2

N3, N4 Pad 129.500 210.000 1.500 SA 350 lf2 1403.090 1403.090 1.000 SA 193 Gr. B7 1757.375 1757.375 0.750 1.330 0.705

[ kg / cm C mm -

2 [ kg / cm ]

[ kg / cm

] ] ]

[ kg / cm [ kg / cm

[ [ [

inch inch inch

] ] ]

The Provided length of engagement of the threads with the stud is adequate.

Copyright 2001 Krupp Uhde Gmbh

Doc.ID-Code Q4-KU-T141.000086-002

Rev

Krupp Uhde

Mechanical Design Calculations MDC NO- 631

Code
QAFCO-4 Expansion Project
UAN (For QHMA)

Page of

01-3030

Calculations for Pad Type Nozzle Nozzle Mark Design Pressure Design Temperature Corrosion Allowance
Tapped Hole Area Loss----------As per Table 2.9 of Dennis Moss, Page 67

P t ci Ah tr t trc tc Ini Ino Inic Inr tn h ha trn L F Ar A1 A2

[ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [ [

-2

] ] ] ] ] ] ] ] ] ] ] ] ] ] ] ] ] ]
2 2 2 2

N3, N4 129.500 210.000 0.150 11.871 2.710 2.800 2.560 2.650 60.000 90.000 60.300 30.150 14.850 9.000 6.625 2.95 60.300 1.000 166.239 2.754 157.730 160.484

[ kg / cm ] C cm cm
2

Minimum Reqd. Thickness of Shell (including C.A) Provided Thickness of Shell (including C.A) Minimum Reqd. Thickness of Shell (excluding C.A) Provided Thickness of Shell (excluding C.A) Inside Diameter of the Pad Nozzle Outside Diameter of the Pad Nozzle Inside Diameter of the Pad Nozzle (including C.A) Inside Radius of the Pad Nozzle (including C.A)Inic/2 Thickness of the Pad Nozzle (Ino-Inic) / 2 Provided Height of the Pad Nozzle (projecting outside) Max. Height that can be provided above the shell = 2.5*tc Required Nozzle Thk. trn = (P*(Ini/2 + ci)) / (FfoE - 0.6P)
Horizontal Limit (Greater of Inic or Inr+tn+tc)

cm cm cm cm cm cm cm cm cm cm cm cm cm -cm cm cm cm

Factor F Area Required to be compensated (Inic x trc x F) + Ah Area available in Shell, A1 = 2 (tc-trc) (L-Inr-tn) Area available in pad forging, A2 = 2[min.(h, ha)](tn-trn) Total Area provided, AT = A1+A2 UNSAFE

] ] ] ]

AT [

Copyright 2001 Krupp Uhde Gmbh

Doc.ID-Code Q4-KU-T141.000086-002

Rev

You might also like