You are on page 1of 74

22 LCD TV chassis PL12.

Service Manual
Contents
TYPE A
22PFL4507/F7 22PFL4507/F8 PHILIPS PHILIPS (Serial No.: ME1) (Serial No.: XA1)

TYPE B
22PFL4907/F7 PHILIPS (Serial No.: ME1)

This service manual contains information of different types of models. This service manual contains information of different types of models. Make sure to refer to the section describing your model. Make sure to refer to the section describing your model.
2012 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes. with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law. 120406

IMPORTANT SAFETY NOTICE


Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended. It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.

TABLE OF CONTENTS
Specifications [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Electrical Adjustment Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Firmware Renewal Mode [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Wiring Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 Exploded Views [TYPE A]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1 [TYPE B]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 Parts List [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1 [TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-4 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

SPECIFICATIONS
[TYPE A]
< TUNER / NTSC >
ANT. Input ---------------------- 75 Unbal., F type Description 1. AFT Pull-In Range 2. Synchronizing Sens. Condition --TV.ch.4 CA.ch.31 CA.ch.87 Unit MHz dB dB dB Nominal 2.3 18 18 18 Limit 2.1 20 20 23

< TUNER / ATSC >


Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) Condition --ch.4 ch.10 ch.41 Unit kHz dBm dBm dBm Nominal --------Limit 100 -76/0 -76/0 -76/+4

< LCD PANEL >


Description 1. Native Pixel Resolution 2. Brightness (w / filter) 3. Viewing Angle Condition Horizontal Vertical --Horizontal Vertical Unit pixels pixels cd/m2 Nominal 1366 768 250 -85 to 85 -80 to 80 Limit -----------

< VIDEO >


Description 1. Over Scan 2. Color Temperature 3. Resolution (composite video) Condition Horizontal Vertical x y Horizontal Vertical line line Unit % % K Nominal 5 5 12000 0.272 0.278 400 350 Limit 55 55 --0.01 0.01 -----

< AUDIO >


All items are measured across 8 load at speaker output terminal with L.P.F. Description 1. Audio MAX Output (ATSC 0dBfs) 2. Audio Distortion (NTSC) Condition Lch/Rch 500mW: Lch/Rch Unit W % Nominal 2.0/2.0 0.5/0.5 Limit 1.8/1.8 2.0/2.0

1-1

PL12.0SP

[TYPE B]
< TUNER / NTSC >
ANT. Input ---------------------- 75 Unbal., F type Description 1. AFT Pull-In Range 2. Synchronizing Sens. Condition --TV.ch.4 CA.ch.31 CA.ch.87 Unit MHz dB dB dB Nominal 2.3 18 18 18 Limit 2.1 20 20 23

< TUNER / ATSC >


Description 1. Received Freq. Range (-28dBm) 2. ATSC Dynamic Range (min / max) Condition --ch.4 ch.10 ch.41 Unit kHz dBm dBm dBm Nominal --------Limit 100 -76/0 -76/0 -76/+4

< LCD PANEL >


Description 1. Native Pixel Resolution 2. Brightness (w / filter) 3. Viewing Angle Condition Horizontal Vertical --Horizontal Vertical Unit pixels pixels cd/m2 Nominal 1366 768 250 -85 to 85 -80 to 80 Limit -----------

< VIDEO >


Description 1. Over Scan 2. Color Temperature [composite video, 100% RASTER] 3. Resolution (composite video) Condition Horizontal Vertical x y Horizontal Vertical line line Unit % % K Nominal 5 5 12000 0.272 0.278 400 350 Limit 55 55 --4% 4.5% -----

< AUDIO >


All items are measured across 8 load at speaker output terminal with L.P.F. Description 1. Audio MAX Output (ATSC 0dBfs) 2. Audio Distortion (NTSC) Condition Lch/Rch 500mW: Lch/Rch Unit W % Nominal 2.0/2.0 0.5/0.5 Limit 1.8/1.8 2.0/2.0

1-2

PL12.0SP

IMPORTANT SAFETY PRECAUTIONS


Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for LCD TV Circuit


1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items: a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage. b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.

d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.

READING SHOULD NOT BE ABOVE 0.5 mA


DEVICE BEING TESTED LEAKAGE CURRENT TESTER

TEST ALL EXPOSED METAL SURFACES

ALSO TEST WITH PLUG REVERSED USING AC ADAPTER PLUG AS REQUIRED

EARTH GROUND

ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES. 2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.

2-1

LTVN_ISP

3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom. 4. Hot Chassis Warning a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.

7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

2-2

LTVN_ISP

Precautions during Servicing


A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc. C. Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double insulated wires 3) High voltage leads D. Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape 2) PVC tubing 3) Spacers 4) Insulators for transistors. E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering. F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.) G. Check that replaced wires do not contact sharp edged or pointed parts. H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it. I. Also check areas surrounding repaired locations. J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set. K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet. L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.

2-3

LTVN_ISP

Safety Check after Servicing


Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1) Table 1: Ratings for selected area AC Line Voltage 110 to 130 V Region U.S.A. or Canada Clearance Distance (d), (d) 3.2 mm (0.126 inches)

Chassis or Secondary Conductor Primary Circuit d' d

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

Fig. 1

2. Leakage Current Test


Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below. Measuring Method: (Power ON) Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

Exposed Accessible Part Z AC Voltmeter (High Impedance)

Earth Ground Power Cord Plug Prongs Fig. 2

Table 2: Leakage current ratings for selected areas AC Line Voltage 110 to 130 V Region U.S.A. or Canada Load Z 0.15 F CAP. & 1.5 k RES. Connected in parallel Leakage Current (i) i 0.5 mA rms Earth Ground (B) to: Exposed accessible parts

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2-4

LTVN_ISP

STANDARD NOTES FOR SERVICING


Circuit Board Indications
1. The output pin of the 3 pin Regulator ICs is indicated as shown.

How to Remove / Install Flat Pack-IC


1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)

Top View Out In Input

Bottom View

2. For other ICs, pin 1 and every fifth pin are indicated as shown.

5 Pin 1

10
3. The 1st pin of every male connector is indicated as shown.

Fig. S-1-1
2. Remove the flat pack-IC with tweezers while applying the hot air.

Pin 1

Pb (Lead) Free Solder


Pb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) CAUTION: 1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC. 2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)

Pb free mark

3-1

TVN_SN

3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.

With Soldering Iron: 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)

CBA

Hot-air Flat Pack-IC Desoldering Machine

Flat Pack-IC

Desoldering Braid

Soldering Iron Masking Tape Tweezers Flat Pack-IC Fig. S-1-3


2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)

Fig. S-1-2

Sharp Pin Fine Tip Soldering Iron

Fig. S-1-4

3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)

3-2

TVN_SN

With Iron Wire: 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5. 4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6) 5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6) Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.

2. Installation
1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. The I mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.) 3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.

Example :

Hot Air Blower

Pin 1 of the Flat Pack-IC is indicated by a " " mark.

Fig. S-1-7

or Iron Wire Soldering Iron To Solid Mounting Point Fig. S-1-5

Presolder

Flat Pack-IC CBA CBA Fine Tip Soldering Iron Fig. S-1-8

Flat Pack-IC Tweezers Fig. S-1-6

3-3

TVN_SN

Instructions for Handling Semiconductors


Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.

1. Ground for Human Body


Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.

2. Ground for Workbench


Be sure to place a conductive sheet or copper plate with proper grounding (1 M) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.

<Incorrect>

CBA

<Correct>

Grounding Band

1M

CBA

1M Conductive Sheet or Copper Plate

3-4

TVN_SN

CABINET DISASSEMBLY INSTRUCTIONS


1. Disassembly Flowchart
This flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
[3] Power Supply CBA [5] Speaker [1] Rear Cover [2] Stand Assembly [6] Stand Holder [8] LCD Panel Assembly [9] Rear Frame [7] Function CBA [4] Digital Main CBA Unit

Step/ Loc. No. [10] [11] (1)

Part LCD Module Front Cabinet (2)

Fig. No.

Removal

Note

D4 --------------D4 -------------- (3) (4)

1,3 3 (5)

*1: TYPE A *2: TYPE B Note: (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures. (2) Parts to be removed or installed. (3) Fig. No. showing procedure of part location (4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connector e.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2) Note (5) Refer to the following "Reference Notes in the Table."

[10] LCD Module [11] Front Cabinet

2. Disassembly Method
Step/ Loc. No. [1] [2] Part Fig. No. Removal 4(S-1), 6(S-2)*1, 7(S-2)*2

Rear Cover D1 Stand Assembly Power Supply CBA

-----

Precautions concerning the LCD Panel Assembly:


1. When you disassemble the LCD Panel Assembly Be careful not to scratch the Reflection Sheet with the edge of Rear Frame when disassembling/ re-assembling it. Be careful not to drop any plastic chip on the Reflection Sheet when/after you remove the Screws. Prohibit to put any external pressure on the Reflection Sheet because the scratch on the back of the Reflection Sheet have direct repercussion on the display screen. Prohibit to put any external pressure on the Sheet Holder or LED Heat Sink Assembly either because it also has repercussion on the display screen via the Reflection Sheet. You need to remove any visible dust from the Reflection Sheet which creates the external pressure between the Reflection Sheet and the Sheet Holder/LED Heat Sink Assembly as a result.

D1 2(S-3) D2 3(S-4), CN601, D5 CN631, CN1001

[3]

---

[4]

4(S-5), CN3011*1, Digital Main D2 CN3905*2, CN3101*1, CBA Unit D5 CN3105*2, CN3801, Jack Holder Speaker Stand Holder Function CBA LCD Panel Assembly D3 --------------D3 (S-6), 2(S-7) D3 Sensor Plate D5 D3 ---------------

---

[5] [6] [7] [8] [9]

----2,3 3 1,3

Rear Frame D4 9(S-8), 2(S-9)

4-1

PL12.0-AB_DC

To prevent the Screw from being stripped, the screw tightening torque should be 13.23 lbfin(6 kgfcm) for the Rear Frame Screw and 5.512 lbfin(2.5 kgfcm) for the LED Heat Sink Assembly Screw. Do not pull the FFC Cable and Board Cable forcefully when you re-assemble. 2. When you disassemble/re-assemble the Function CBA on the Front Cabinet Detach the Function CBA, which is attached on the Front Cabinet with double-sided tape, without breaking it. When you put the Function CBA back on the New Front Cabinet, you need to use specified new double-sided tape and put the Function CBA onto the New Front Cabinet with equal pressure to the Board. (The gap more than 0.015 inch (0.4 mm)

between the Front Cabinet and Function CBA will impair the sensor sensitivity.) Prepare for substitutional Function CBA in case you break it when you detach it from the Front Cabinet. 3. Performance Test after reassembling the LCD Panel Assembly After you swap any of the Front Cabinet, Rear Frame or Function CBA, you need to make sure that there is no Gomikami/Black Spot with foreign material or Mura/White Spot on the display screen. Make sure there is no malfunction on the display screen by checking the White Mode and White 20% Mode in the Purity Check Mode. Check the operational sensitivity on Touch Sensor Control Panel to make sure everything functions normally.

TYPE A
(S-1)

(S-1)

(S-2)

[2] Stand Assembly

[1] Rear Cover

TYPE B

(S-1)

(S-1)

(S-3)

(S-2)

Fig. D1

4-2

PL12.0-AB_DC

TYPE A

[4] Digital Main CBA Unit

(S-4)

Jack Holder

(S-5)

[3] Power Supply CBA


(S-4)

Jack Holder

TYPE B Fig. D2

[8] LCD Panel Assembly*1

[6] Stand Holder

Sensor Plate Double-sided tape

(S-6)

[7] Function CBA*1

(S-7)

[5] Speaker Fig. D3

*1: Make sure to read all the precautions on page 4-1, 4-2 when you disassemble/re-assemble the LCD Panel Assembly.

4-3

PL12.0-AB_DC

[11] Front Cabinet*1

[10] LCD Module*1


Reflection Sheet Cable FFC Cable Sheet Holder

[9] Rear Frame*1


(S-8)

(S-8)

(S-8) LED Heat Sink Assembly

Sheet Holder (S-8) (S-8) (S-9)

Fig. D4
*1: Make sure to read all the precautions on page 4-1, 4-2 when you disassemble/re-assemble the LCD Panel Assembly.

4-4

PL12.0-AB_DC

TV Cable Wiring Diagram

To LCD Panel Assembly

To LCD Panel Assembly Digital Main CBA Unit

Power Supply CBA


CN1001 *1 CN3011 *2 CN3905

*1 CN3701 CN631 *2 CN3601

CN601 CN3801

*1 CN3101 *2 CN3105 To Speaker To AC Cord

*1: TYPE A *2: TYPE B

Function CBA
CN4001

Fig. D5

4-5

PL12.0-AB_DC

ELECTRICAL ADJUSTMENT INSTRUCTIONS


[TYPE A]
General Note: CBA is abbreviation for Circuit Board Assembly.
Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

1. Purity Check Mode


This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. 1. Enter the service mode. 2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.

Purity Check Mode


White mode [7] button

Test Equipment Required


1. Remote control unit 2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
[7] button Black mode

How to set up the service mode:


Service mode:
1. Turn the power on. 2. Press [MENU] button to display Setup menu. 3. Select Features. 4. Select Software Upgrade. 5. Select Current Software Info. 6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
"*" differs depending on the models.

[7] button White 50% mode

[7] button Red, Green, Blue mode

Code: Pic code: Panel-Option code: MIPS:

*******-**-**-****-** ***-*****-***-***-*-** **-***-***-***-*** Push 0 key

[7] button V-ramp mode


Press "POWER" key to exit. Safety: HDMI EDID: HDMI UART: Touch Sensor Ver: Safety_Non ** OFF -.-- / ---

Total Watch Time: ***** Lightsensor: **

[7] button White 20% mode

Note: When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.

5-1

PL12.0EA

The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.

6. Press [MENU] button. The internal Raster signal appears in the screen. (Internal (Single) appears in the upper right of the screen as shown below.)

2. White Balance Adjustment


Internal (Single)

Purpose: To mix red and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. ITEM Color temperature Input Signal SPECIFICATION x= 0.272 0.002 y= 0.278 0.002 Internal pattern (40/80% raster) CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310. 60min. (Retail MODE/100IRE Raster HDMI 1080i@60) Shipment setting/ Retail MODE 25C 5C
Internal (Single) HDB 0

7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000K (x= 0.272 / y= 0.278 0.002). 8. Press [1] button to select the HDR for High Drive Red adjustment (HDR appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. 9. If necessary, adjust the HDB or HDR again. 10. Press [6] button to select the LDB for Low Drive Blue adjustment (LDB appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

Measurement point Screen center M. EQ.

Aging time MODE setting of TV Ambient temperature

1. Operate the unit for more than 60 minutes. 2. Enter the service mode. 3. Press [VOLUME DOWN] button three times on the remote control unit to select Drive setting mode. Drive appears in the screen. 4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
To avoid interference from ambient light, this adjustment should be performed in a dark room. Perpendicularity

LDB

11. Press [4] button to select the LDR for Low Drive Red adjustment (LDR appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. 12. If necessary, adjust the LDB or LDR again. 13. Press [VOLUME DOWN] button to shift to the Debugging Message mode. If there is no message under [WB] section, this adjustment completes. If Drive settings are NG. Retry. is displayed, repeat above steps from 5. to 12. Then check Debugging Message again. If Drive settings are NG. Retry. is displayed, replace the LCD Panel or Digital Main CBA. 14. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.

Color Analyzer

Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 5. Press [3] button to select the HDB for High Drive Blue adjustment. (HDB appears in the screen.)

5-2

PL12.0EA

[TYPE B]
General Note: CBA is abbreviation for Circuit Board Assembly.
Note: Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

1. Purity Check Mode


This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels. 1. Enter the service mode. 2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.

Purity Check Mode


White mode [7] button

Test Equipment Required


1. Remote control unit 2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.

[7] button Black mode

How to set up the service mode:


Service mode:
1. Turn the power on. 2. Press [0], [6], [2], [5], [9], [6], and [INFO] buttons on the remote control unit in this order. The following screen appears.
"*" differs depending on the models.

[7] button White 50% mode

[current] File code: Total checksum: Panel-Option code:

***-****_***_* Push "0" key **-***-***-***-***-*** ***-***-***-***-***

[7] button Red, Green, Blue mode

Press "POWER" key to exit. MAC address: ESN: Tuner: HDMI UART: Touch Sensor Ver: EDID: **:**:**:**:**:** *****************************

**** TotalWatchTime: OFF SystemTime: -.-- / --Push "0" key Lightsensor:

***** **:** **

[7] button V-ramp mode

[7] button White 20% mode

Note: When entering this mode, the default setting is White mode.

3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.

5-3

PL12.0_B (A2776UH)_EA

The White Balance Adjustment should be performed when replacing the LCD Panel or Digital Main CBA.

6. Press [MENU] button. The internal Raster signal appears in the screen. (Internal (Single) appears in the upper right of the screen as shown below.)

2. White Balance Adjustment


Internal (Single)

Purpose: To mix red and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish. ITEM Color temperature Input Signal SPECIFICATION x= 0.272 0.002 y= 0.278 0.002 Internal pattern (30/50/80% raster) CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310. 60min. (Retail MODE/100IRE Raster HDMI 1080i@60) Shipment setting/ Retail MODE 25C 5C
Internal (Single) HDB 0

7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000K (x= 0.272 / y= 0.278 0.002). 8. Press [1] button to select the HDR for High Drive Red adjustment (HDR appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. 9. If necessary, adjust the HDB or HDR again. 10. Press [9] button to select the LDB for Low Drive Blue adjustment (LDB appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.

Measurement point Screen center M. EQ.

Aging time MODE setting of TV Ambient temperature

1. Operate the unit for more than 60 minutes. 2. Enter the service mode. 3. Press [VOLUME DOWN] button three times on the remote control unit to select Drive setting mode. Drive appears in the screen. 4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
To avoid interference from ambient light, this adjustment should be performed in a dark room. Perpendicularity

LDB

11. Press [7] button to select the LDR for Low Drive Red adjustment (LDR appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. 12. If necessary, adjust the LDB or LDR again. 13. Press [CH RETURN] or [PREV CH] to shift to the initial screen in the service mode. If [White Balance] message with a green color is displayed on the upper right of the screen, this adjustment completes. If [White Balance] message with a red color is displayed, repeat above steps from 5. to 12. Then check the initial screen in the service mode again. If [White Balance] message with a red color is displayed, replace the LCD Panel or Digital Main CBA. 14. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.

Color Analyzer

Note: The optical receptor must be set perpendicularly to the LCD Panel surface. 5. Press [3] button to select the HDB for High Drive Blue adjustment. (HDB appears in the screen.)

5-4

PL12.0_B (A2776UH)_EA

HOW TO INITIALIZE THE LCD TV


The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.

[TYPE A]
1. Turn the power on. 2. Enter the service mode. - To cancel the service mode, press [ ] button on the remote control unit. 3. Press [FREEZE] button on the remote control unit to initialize the LCD television. 4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initialization is completed.

[TYPE B]
1. Turn the power on. 2. Enter the service mode. - To cancel the service mode, press [ ] button on the remote control unit. 3. Press [COLOR(red)] button on the remote control unit to initialize the LCD television. 4. "INITIALIZE" will appear in the upper right of the screen. The whole screen color will change to green and "INITIALIZE FINISH" will appear in the center of the screen when initialization is completed.

6-1

PL12.2_INT

FIRMWARE RENEWAL MODE


[TYPE A]
Equipment Required
a. USB storage device b. Remote Control Unit

Firmware Update Procedure


User Upgrade (Filename example: TVNB012_00_UF_XX91_AA.ecc)
Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add FACT_ at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the FACT_ from the filename. Update procedure 1. Turn the power on. 2. Press [MENU] button to display Menu. 3. Select Features. 4. Select Software Upgrade. 5. Select Upgrade to display Upgrade screen. 6. Press [OK] button to display Software Upgrade screen. 7. Select USB and press [OK] button. 8. Insert the USB storage device to the USB port as shown below.
Rear Cabinet USB port

11. The update will start and the following will appear in the screen.
"*" differs depending on the models.

Software Upgrade

Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Current Version: *******-***-*-***-**** New Version: *******-***-*-***-****

*1

Downloading... 0%

Note: If the above screen isnt displayed, repeat from step 1. The appearance shown in *1 is described as follows.

USB storage device

Appearance Downloading... Writing... Checking...

State Downloading the firmware from the USB storage device. Writing the downloaded firmware in flash memory. Checking the new firmware.

12. When the firmware update is completed, the following will appear in the screen.
Software Upgrade

9. Select Check and press [OK] button. 10. Select Upgrade and press [OK] button to start software upgrade.

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again. 7-1 PL12.0_A FW

Factory Upgrade (Firmware Upgrade/Flash Upgrade)


Firmware Upgrade (Filename example: FACT_TVNB012_00_UF_XX91_AA.ecc) Upgrade the firmware and initialize the setting values. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add FACT_ at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the FACT_ from the filename. Flash Upgrade (Filename example: ALL_TVNB012_00_UF_XX91_AA.ecc) Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc. Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the TV after the initialization. The Flash Upgrade will be done by it's unique file. The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade. Update procedure 1. Turn the power off. 2. Insert the USB storage device to the USB port as shown below.
Rear Cabinet USB port

The appearance shown in *1 is described as follows. Appearance Downloading... Writing... Checking... State Downloading the firmware from the USB storage device. Writing the downloaded firmware in flash memory. Checking the new firmware.

USB storage device

5. When the firmware update is completed, the following will appear in the screen.
Software Upgrade

3. Turn the power on. 4. The update will start and the following will appear in the screen.
"*" differs depending on the models.

The software upgrade is completed. Remove USB storage device, turn TV off then on again.

Software Upgrade

Software upgrade in progress. Please wait. Do not remove the USB storage device or turn the TV off while upgrade is in progress. Current Version: *******-***-*-***-**** New Version: *******-***-*-***-****

Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Service mode initial screen with a word INITIALIZED will appear in the screen. The color of the word INITIALIZED will change from red to green when initialization is completed.

*1

Downloading... 0%

Note: If the above screen isnt displayed, repeat from step 1.

7-2

PL12.0_A FW

[TYPE B]
Equipment Required
1. USB storage device 2. Remote Control Unit (Files included in the USB storage device are displayed.)
"*" differs depending on the models.
Select an upgrade file

Firmware Update Procedure


1. Turn the power off and unplug the AC Cord. 2. Insert the USB storage device to the USB port as shown below.
Rear Cabinet USB port

*****_******.upg *****_******.upg *****_******.upg

Cancel

1 23

USB storage device

Note: To cancel the update mode, select Cancel and press the [OK] button. 10. Select the file and press [OK] button. 11. The update will start and the following will appear in the screen.
"*" differs depending on the models.
Current Version: ***-****-***-* New Version: ***-****-***-* Are you sure you want to update?

3. Plug the AC Cord and turn the power on. 4. After few seconds, the menu mode will appear in the screen. Note: After 30 seconds without an operation, the menu mode will disappear automatically. To display the menu mode again, press the [MENU] button on the remote control unit. 5. Select Setup and press the [OK] button to display the setup menu. 6. Select Software. 7. Select Software update. 8. Select USB. 9. Press the [OK] button on the remote control unit to enter the update mode. Update file selection screen appears as follows.
No Yes

Note: If the above screen isnt displayed, repeat from step 1. 12. Select Yes and press the [OK] button to update. Note: Do not remove the USB storage device or turn the TV off while update is in progress. 13. When the firmware update is completed, the following will appear in the screen.

Update your TV with new software:

Done

Software update is successful. Please remove the USB storage device and restart the TV set.

Remove the USB storage device from the USB port. Turn the power off and turn the power on again. 7-3 PL12.0_B (A2776UH)_FW

TROUBLESHOOTING
[Power Supply Section]
FLOW CHART NO.1 The power cannot be turned on. No Yes

Is the fuse (F601) normal?

See FLOW CHART No.2 <The fuse blows out.>

Is normal state restored when once unplugged power cord is plugged again after several seconds?
Yes Is the P-ON+21V line voltage normal? Yes

No Check if there is any leak or short-circuit on the primary circuit component and repair it if defective. (D601, D602, D603, D604, Q601, Q602, T601)

No

Check each rectifying circuit of the secondary circuit and repair it if defective.
FLOW CHART NO.2 The fuse blows out.

Check if there is any leak or short-circuit on the primary circuit component and repair it if defective.

Check if there is any leak or short-circuit on the each rectifying circuit component of secondary side and repair it if defective.

Make sure to repair the primary circuit component before replacing the fuse.
FLOW CHART NO.3 When the output voltage fluctuates.

Does the photocoupler circuit on the secondary side operate normally?


Yes

No

Check IC601, D660, D661B, Q652, Q653 and their periphery circuit. Repair it if defective.

Check IC601, D605, D607, D608, D609, D610, Q601, Q602 and their periphery circuit. Repair it if defective.

FLOW CHART NO.4 When buzz sound can be heard in the periphery of power circuit.

Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side. Repair it if defective. (D650, D653, Q656)

8-1

PL12.0ATR

FLOW CHART NO.5 P-ON+21V is not output.

Is approximately +21V voltage supplied to the cathode of D650?


Yes

No

Check D650, C651, C652 and their periphery circuit. Repair it if defective.

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

FLOW CHART NO.6 AMP+13V is not output. No

Is approximately +13V voltage supplied to the cathode of D653?


Yes

Check D653, D654, C654, C655 and their periphery circuit. Repair it if defective.

Check if there is any leak or short-circuit on the load circuit. Repair it if defective.

FLOW CHART NO.7 AL+3.3V is not output. No

Is approximately +21V voltage supplied to the collector of Q656?


Yes

Check D650, C651, C652 and their periphery circuit. Repair it if defective.

Is approximately +4V voltage supplied to the base of Q656?


Yes

No

Check D662 and their periphery circuit. Repair it if defective.

Replace Q656.

8-2

PL12.0ATR

[Video Signal Section]


FLOW CHART NO.1 The key operation is not functioning. No

When touching each buttons, does the Pin(6) voltage of CN4001 decrease?
Yes Replace Digital Main CBA Unit.

Is approximately +3.3V voltage supplied to Pin(1) of CN4001? Yes Replace IC4001 or Function CBA. No Check AL+3.3V line and repair it if defective.

FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) No

Is approximately +3.3V voltage supplied to Pin(3) terminal of the remote control receiver (RS4051)? Yes Is the "L" pulse supplied to Pin(1) terminal of remote control receiver (RS4051) when the infrared remote control is activated? Yes Is the "L" pulse supplied to Pin(5) of CN4001?
Yes Replace Digital Main CBA Unit.

Check AL+3.3V line and repair it if defective.

No

Replace the remote control receiver (RS4051) or the remote control unit. Check the line between Pin(1) of remote control receiver (RS4051) and Pin(5) of CN4001. Repair it if defective.

No

FLOW CHART NO.3 Picture does not appear normally. No

Is approximately +21V voltage supplied to Pin(1, 2, 7, 8) of CN631?


Yes

See FLOW CHART NO.5 <P-ON+21V is not output. [Power Supply Section]> See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

Is approximately +3.3V voltage supplied to Pin(13) of CN631?


Yes

No

Digital Main CBA Unit or LCD Panel Assembly may be defective. Check and replace these parts.

8-3

PL12.0ATR

[Audio Signal Section]


FLOW CHART NO.1 Audio is not output normally.

Is approximately +13V voltage supplied to Pin(10, 11) of CN631? Yes Is approximately +3.3V voltage supplied to Pin(13) of CN631? Yes Are the audio signals output to Pin(1, 4) of CN3801?
Yes

No

See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]>

No

See FLOW CHART NO.7 <AL+3.3V is not output. [Power Supply Section]>

No

Replace Digital Main CBA Unit.

SP3801, SP3802 or CL3801 may be defective. Check and replace these parts.

8-4

PL12.0ATR

IC3005 (MAIN MICRO CONTROLLER)

KEY-IN1 A15 REMOTE C14 LED1 D14 LED DRIVE Q3501, Q3502

RS4051
AL+3.3V

REMOTE SENSOR
D4051 POWER

IC4001 (TOUCH SENSOR) POWER 16 SOURCE 17 MENU 18


2 SOURCE 3 MENU

POWER SOURCE MENU CH UP 19 CH DOWN 21 VOL UP 22


6 CH UP

TO VIDEO/AUDIO BLOCK DIAGRAM

VGA-SCL VGA-SDA AUDIO-MUTE

G14 VGA-SCL F14 VGA-SDA C1 AUDIO-MUTE

CN3101 5 6 2 1 4
REMOTE LED1 SCL SDA KEY-IN1

CN4001 5 4 8 9 6

4 SCL 5 SDA 1 POWER

CH UP CH DOWN VOL UP VOL DOWN 23


11 CH DOWN 12 VOL UP 13 VOL DOWN

[TYPE A] 1. System Control Block Diagram

TU3901 (TUNER UNIT) SCL R12 SDA T12


4 SCL 3 SDA

VOL DOWN

BLOCK DIAGRAMS

9-1
AL+3.3V

IC3006 (MEMORY)

FUNCTION CBA
P-ON-H2 B16 Q3005 SCK SIN SOUT CS Q3006

SCK SI SO CS

6 5 2 1

T11 P11 R11 P12

RESET J15

RESET IC3009

CN3701 7 P-ON-H2 8 RESET

CN631 17 16

P-ON-H2 RESET

TO POWER SUPPLY BLOCK DIAGRAM

X3001 25MHz OSC

H15 XIN25 H16 XOUT25

PROTECT3 B13 BACKLIGHT-SW E2 BACKLIGHT-ADJ F3

CN3701 4 PROTECT3 2 BACKLIGHT-SW 3 BACKLIGHT-ADJ

CN631 20 22 21

PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ

TO LED BACKLIGHT DRIVE BLOCK DIAGRAM

BACKLIGHT-SW

TO VIDEO/AUDIO BLOCK DIAGRAM

PL12.0ABLS
DIGITAL MAIN CBA UNIT

POWER SUPPLY CBA

VIDEO SIGNAL

AUDIO SIGNAL

JK3001 PC-RGB IN

13

IC3013

VGA-R-IN VGA-G-IN VGA-B-IN VGA-HSYNC VGA-VSYNC

BUFFER GATE

14

IC3014

BUFFER GATE

15

Q3301

BUFFER

12

Q3302

BUFFER

TU3901 (TUNER UNIT)


DIF-OUT1 DIF-OUT2 IF-AGC

DIF-OUT1 6 DIF-OUT2 7 IF-AGC 5

JK3702

2. Video/Audio Block Diagram

COMPONENT -Y/VIDEO-IN

COMPONENT -Pb-IN

COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN COMP-DET

TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM

COMPONENT -Pr-IN

9-2
Q3701 BUFFER
IC3801 (AUDIO AMP)
4

JK3701

AUDIO(L)-IN

AUDIO(L)-IN AUDIO(R)-IN

AUDIO(R)-IN

DIGITAL AUDIO-OUT (COAXIAL)

SPDIF

DRIVE
1

AMP(R)-OUT

JK3703 HEADPHONE JACK


6

DRIVE MUTE CONTROL

9 8

AMP(L)-OUT

Q3801 Q3803 AMP+13V Q3804

AUDIO-MUTE VGA-SCL VGA-SDA BACKLIGHT-SW

SP3801 SPEAKER L-CH

SP(L) GND SP(R) GND

CN3801 1 2 4 3

TO SYSTEM CONTROL BLOCK DIAGRAM

PL12.0ABLVA

SP3802 SPEAKER R-CH

DIGITAL MAIN CBA UNIT

VIDEO SIGNAL IC3005 (DIGITAL SIGNAL PROCESS)


A14 HSYNC B14 VSYNC

AUDIO SIGNAL

VGA-HSYNC VGA-VSYNC

LCD PANEL ASSEMBLY

VGA-R-IN VGA-G-IN VGA-B-IN COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN SW A/D CONVERTER


C11 A9 C7 C9 D8 B11 C10

LVDS TX

TO VIDEO/AUDIO BLOCK DIAGRAM


A12 B12

DIF-OUT1 DIF-OUT2

DEMODULATOR /MPEG DECODER

IF-AGC COMP-DET
A16 IF-AGC N12 COMP-DET

N15 N16 P15 P16 R15 R16 T14 R14 T15 T16
ED0(+) ED0(-) ED1(+) ED1(-) ED2(+) ED2(-) ED3(+) ED3(-) EC(+) EC(-)

CN3011 19 20 16 17 14 15 8 9 11 12

AUDIO(L)-IN AUDIO(R)-IN SPDIF AMP(L)-OUT AMP(R)-OUT


A8 B8 N10 B7 A7

AUDIO I/F

AUDIO DECODER DIGITAL SIGNAL PROCESS

3. Digital Signal Process Block Diagram

9-3
HDMI I/F Q3201 B3 A3 B2 A2 B1 A1 B4 A4 C15 C16 VIDEO DECODER

JK3003 HDMI-IN

7 9 4 6 1 3 10 12 16 15

TMDS-D0(+) TMDS-D0(-) TMDS-D1(+) TMDS-D1(-) TMDS-D2(+) TMDS-D2(-) TMDS-CLOCK(+) TMDS-CLOCK(-) HDMI-DATA HDMI-CLOCK

BUFFER

Q3202

BUFFER

IC3002 (DDR2 SDRAM) N4,N7,N8,P3,P4, P6-P8,R3,R4,R6, R8,T2-T5 H1,H2,J1,J2,J4,K1, K3,L1,L2,M1-M3,N1 B1,B9,C2,C8, D1,D3,D7,D9, F1,F9,G2,G8, DATA(0-15) H1,H3,H7,H9 M2,M3,M7,M8, N2,N3,N7,N8, ADDRESS(0-12) P2,P3,P7,P8,R2

PL12.0ABLD

DIGITAL MAIN CBA UNIT

LCD PANEL ASSEMBLY

P-ON+21V

Q1001 IC1001 (LED BACKLIGHT DRIVER)

10 OVP 2

DRIVE

16 14 13 1

DRIVE
3

4. LED Backlight Drive Block Diagram

TO SYSTEM CONTROL BLOCK DIAGRAM DRIVE


5

BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3

CONTROL LOGIC

9-4
DRIVE
4

CN1001 4 6 7 2 1

VLED ILED1 ILED2 ILED3 ILED4

POWER SUPPLY CBA

PL12.0ABLBD

CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
4A 125V

CAUTION ! : For continued protection against risk of fire, replace only with same type 4A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

HOT CIRCUIT. BE CAREFUL.

AC601 AC CORD D601- D604 T601 6


8

F601 4A/125V BRIDGE RECTIFIER Q650 RESET


5 9

L601

CN601 2 1

LINE FILTER

CN631 10,11 13 1,2 7,8


AMP+13V AL+3.3V P-ON+21V P-ON+21V CN3701 13,14 11 16,17 22,23

AMP+13V AL+3.3V P-ON+21V

4A 125V

DIGITAL MAIN CBA UNIT

Q501 SWITCHING

10 4

5. Power Supply Block Diagram

2 11

P-ON+21V

9-5
1 12

Q601 SWITCHING Q656 +3.3V REG.

RESET P-ON-H2

TO SYSTEM CONTROL BLOCKDIAGRAM

IC601 ERROR VOLTAGE DET 4 1 2 3

Q602 SWITCHING CONTROL

Q652

Q653

HOT

COLD
POWER SUPPLY CBA

PL12.0ABLP

IC3101 (MAIN MICRO CONTROLLER) U26 USB0(+) U25 USB0(-) KEY-IN1 AF2 REMOTE Y23 LED1 W23 LED DRIVE Q3101

WIRELESS LAN ADAPTOR

CN3705 USB0(+) USB0(-)

USB JACK

CN3704 USB1(+) USB1(-) V25 USB1(+) U24 USB1(-)

IC3902 (ETHERNET I/F) RS4051


AL+3.3V

ETHERNET JACK

CN3706 TD(+) TD(-) RD(+) RD(-)


REMOTE SENSOR
D4051 POWER

1 2 4 5 23 24 25 26

ETHERNET I/F

14 16 17 18

AA3 W5 W4 AB2 RMII-RXD0 RMII-RXD1 RMII-RXD2 RMII-RXD3

IC4001 (TOUCH SENSOR) POWER 16 SOURCE 17 MENU 18


2 SOURCE 3 MENU

Y3 V6 Y4 Y2 RMII-TXD0 RMII-TXD1 RMII-TXD2 RMII-TXD3


REMOTE LED1 SCL SDA KEY-IN1

POWER SOURCE MENU CH UP 19 CH DOWN 21 VOL UP 22


6 CH UP 11 CH DOWN 12 VOL UP

X3701 25MHz OSC

CN3105 5 6 2 1 4 IC3103 (MEMORY) STM-SCL AC5 STM-SDA AE4


6 SCL 5 SDA

CN4001 5 4 8 9 6

4 SCL 5 SDA 1 POWER

42 XI 43 XO

RESET 29

AD1 HUB-RESET

CH UP CH DOWN VOL UP VOL DOWN 23 VOL DOWN

[TYPE B] 1. System Control Block Diagram

9-6
TU3001 (TUNER UNIT) Y20 AA20 V23 P1 V20 VGA-SCL VGA-SDA AMP-MUTE COMP-DET LCD-P-ON TU-SCL AE10 TU-SDA AD9
6 SCL 5 SDA

TO VIDEO/AUDIO BLOCK DIAGRAM

VGA-SCL VGA-SDA AMP-MUTE COMP-DET LCD-P-ON

13 VOL DOWN

FUNCTION CBA

X3101 24.576MHz OSC

AF3 AXI AE3 AXO

P-ON-H2 AE2 RESET AB6

RESET IC3009

CN3601 7 P-ON-H2 8 RESET

CN631 7 8

P-ON-H2 RESET

TO POWER SUPPLY BLOCK DIAGRAM

PROTECT3 AE1 BACKLIGHT-SW K25 BACKLIGHT-ADJ G6

CN3601 4 PROTECT3 2 BACKLIGHT-SW 3 BACKLIGHT-ADJ

CN631 4 2 3

PROTECT3 BACKLIGHT-SW BACKLIGHT-ADJ

TO LED BACKLIGHT DRIVE BLOCK DIAGRAM

PL12.0BBLS

DIGITAL MAIN CBA UNIT

POWER SUPPLY CBA

VIDEO SIGNAL

AUDIO SIGNAL

VGA-R-IN VGA-G-IN VGA-B-IN VGA-HSYNC VGA-VSYNC

JK3713 PC-RGB IN TU3001 (TUNER UNIT) DIF-OUT1 6 DIF-OUT2 7 IF-AGC 5


DIF-OUT1 DIF-OUT2 IF-AGC

13

14

15

12

JK3701

COMPONENT -Y/VIDEO-IN

COM-VIDEO-Y/VIDEO-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN

COMPONENT -Pb-IN TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM

2. Video/Audio Block Diagram

COMPONENT -Pr-IN

9-7
Q3001 BUFFER
IC3801 (AUDIO AMP)

JK3706

AUDIO(L)-IN

AUDIO(L)-IN AUDIO(R)-IN

AUDIO(R)-IN

DIGITAL AUDIO-OUT (COAXIAL)

SPDIF

39,40
32

DRIVE

PWM

AMP(R)-OUT

JK3801 HEADPHONE JACK

11,12

DRIVE

PWM

19 34

AMP(L)-OUT

Q3801 Q3803
17

CONTROL LOGIC

P-ON+5V Q3802

SP3801 SPEAKER L-CH

SP(L) GND SP(R) GND

CN3801 1 2 4 3

AUDIO-MUTE VGA-SCL VGA-SDA COMP-DET LCD-P-ON

TO SYSTEM CONTROL BLOCK DIAGRAM

PL12.0BBLVA

SP3802 SPEAKER R-CH

DIGITAL MAIN CBA UNIT

VIDEO SIGNAL IC3101 (DIGITAL SIGNAL PROCESS) AB9 VGA-HSYNC AA9 VGA-VSYNC

AUDIO SIGNAL

LCD PANEL ASSEMBLY

VGA-HSYNC VGA-VSYNC

VGA-R-IN VGA-G-IN VGA-B-IN COM-VIDEO-Y/CVBS-IN COM-VIDEO-Pb-IN COM-VIDEO-Pr-IN Y18 AA17 Y17 AA15 AA14 AB14 AB17 SW A/D CONVERTER AE6 AD6 AD7 IF-AGC DEMODULATOR /MPEG DECODER

TO VIDEO/AUDIO BLOCK DIAGRAM

DIF-OUT1 DIF-OUT2 IF-AGC

LVDS TX AUDIO I/F

AMP(L)-OUT AMP(R)-OUT AUDIO(L)-IN AUDIO(R)-IN SPDIF

JK3717 HDMI-IN1
Q3003 BUFFER

AC10 AB11 AD13 AE13 AD10

Q3002 BUFFER

Q3004 MUTE

J3 J2 H3 H2 G3 H1 G1 G2 G4 H4

CN3905 20 19 17 16 15 14 9 8 12 11

LV-ED0(-) LV-ED0(+) LV-ED1(-) LV-ED1(+) LV-ED2(-) LV-ED2(+) LV-ED3(-) LV-ED3(+) LV-ECLK(-) LV-ECLK(+)

AB25 ARC-MUTE AUDIO DECODER DIGITAL SIGNAL PROCESS

3. Digital Signal Process Block Diagram

9-8
HDMI I/F HDMI SW AE23 AF23 AE24 AF24 AE25 AF25 AE22 AF22 AB23 AB22 VIDEO DECODER AE19 AF19 AE20 AF20 AD21 AE21 AD18 AE18 Y21 W21

14 7 9 4 6 1 3 10 12 16 15

ARC DATA0(+) DATA0(-) DATA1(+) DATA1(-) DATA2(+) DATA2(-) CLOCK(+) CLOCK(-) HDMI-DATA HDMI-CLOCK AD15 AE15 AE16 AF16 AE17 AF17 AE14 AF14 AA24 AA22

JK3715 HDMI-IN2

IC3401 (DDR3 SDRAM) DATA(0-15) ADDESS(0-13) IC3402 (DDR3 SDRAM) DATA(16-31) ADDESS(0-13) IC3102 (NAND FLASH MEMORY) DATA(0-7)

7 9 4 6 1 3 10 12 16 15

DATA0(+) DATA0(-) DATA1(+) DATA1(-) DATA2(+) DATA2(-) CLOCK(+) CLOCK(-) HDMI-DATA HDMI-CLOCK

JK3716 HDMI-IN3

7 9 4 6 1 3 10 12 16 15

DATA0(+) DATA0(-) DATA1(+) DATA1(-) DATA2(+) DATA2(-) CLOCK(+) CLOCK(-) HDMI-DATA HDMI-CLOCK

PL12.0BBLD

DIGITAL MAIN CBA UNIT

LCD PANEL ASSEMBLY

P-ON+21V

Q1001 IC1001 (LED BACKLIGHT DRIVER)

10 OVP 2

DRIVE

16 14 13 1

DRIVE
3

4. LED Backlight Drive Block Diagram

TO SYSTEM CONTROL BLOCK DIAGRAM DRIVE


5

BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3

CONTROL LOGIC

9-9
DRIVE
4

CN1001 4 6 7 2 1

VLED ILED1 ILED2 ILED3 ILED4

POWER SUPPLY CBA

PL12.0BBLBD

CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
4A 125V

CAUTION ! : For continued protection against risk of fire, replace only with same type 4A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

HOT CIRCUIT. BE CAREFUL.

AC601 AC CORD D601- D604 T601 6


8

F601 4A/125V BRIDGE RECTIFIER Q650 RESET


5 9

L601

CN601 2 1

LINE FILTER

CN631 10,11 13 1,2 7,8


AMP+13V AL+3.3V P-ON+21V P-ON+21V CN3601 13,14 11 16,17 22,23

AMP+13V AL+3.3V P-ON+21V

4A 125V

DIGITAL MAIN CBA UNIT

Q501 SWITCHING

10 4

5. Power Supply Block Diagram

2 11

P-ON+21V

9-10
1 12

Q601 SWITCHING Q656 +3.3V REG.

RESET P-ON-H2

TO SYSTEM CONTROL BLOCKDIAGRAM

IC601 ERROR VOLTAGE DET 4 1 2 3

Q602 SWITCHING CONTROL

Q652

Q653

HOT

COLD
POWER SUPPLY CBA

PL12.0BBLP

SCHEMATIC DIAGRAMS / CBA AND TEST POINTS


Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark # in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.

Notes:
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared. 2. All resistance values are indicated in ohms (K = 103, M = 106). 3. Resistor wattages are 1/4W or 1/6W unless otherwise specified. 4. All capacitance values are indicated in F (P = 10-6 F). 5. All voltages are DC voltages unless otherwise specified. 6. This schematic diagrams are masterized version that should cover the entire PL12.0 chassis models. Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the PL12.0 chassis. Please refer to the parts lists for each models. 7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.

10-1

PL12.0SC

LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V.

2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since the drawings were prepared. 2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.

4. Voltage indications on the schematics are as shown below:


Plug the TV power cord into a standard AC outlet.:

1 (Unit: Volt) 5.0

3 5.0 Power on mode

Voltage

Indicates that the voltage is not consistent here.

5. How to read converged lines


1-D3 Distinction Area Line Number (1 to 3 digits) 3 AREA D3 1-B1

2 Examples: 1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 1 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".

AREA B1 1-D3 A B C D

6. Test Point Information


: Indicates a test point with a jumper wire across a hole in the PCB. : Used to indicate a test point with a component lead on foil side. : Used to indicate a test point with no test pin. : Used to indicate a test point with a test pin.

The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function.

10-2

PL12.0SC

Power Supply Schematic Diagram


CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.

4A 125V

CAUTION ! : For continued protection against risk of fire, replace only with same type 4A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

HOT CIRCUIT. BE CAREFUL.

POWER SUPPLY CBA


R601 1.2M/1/2W C603 OPEN SA601 SURGE ABSORBER

BC1002 WIRE

C1001 330/25V

C1002 OPEN

C1003 1

C1004 1

L1001 47uH D1001 SK110TC D1004 OPEN C1007 OPEN Q1001 AP18T10AGH-HF 22.4 D (SWITCHING) G 2.6 0.1 S R1003 0.33/1W R1002 200 C1006 470P C1005 OPEN

D102A HSC119TRF-E D1002 R1001 10

AC601 AC CORD

CN601 1 2 F601 4A/125V

C1010 47/100V

C1009 C1008 R1004 1/100V 1/100V 160K R1005 430K

C1014 1000P

D1005B OPEN

D1005 OPEN

R1006 27K

4A 125V

C604 0.47/275V L601 LINE FILTER C601 OPEN D601 1N5397BD D604 1N5397BD R602 1.2/3W D602 1N5397BD D603 1N5397BD C650 1500P/1KV D650 SB3150BH C651 470/25V C652 1000/25V D652 OPEN D652A OPEN 3.0 1 0.5 2 0.5 3 0.5 4 IC1001 HA7209PC LED BACKLIGHT DRIVER

C1015 OPEN

R1011 100K

R1010 10K

C1011 OPEN

C1012 OPEN

C1013 1/100V

24 1.2 DRIVE DRIVE NU 23 COMP 22 1.4 MCP 21 0 SEL 20 0 VIN 19 19.3 GND 18 0 DRIVE LDO 17 4.9 16 2.6 15 0 14 0.1 13 3.0

R403 OPEN R1012 C1016 1 100 C1018 OPEN R1019 0 R1015 240 R1018 OPEN C1017 0.1 C1021 OPEN R1014 240

D402B 24BSB-T26

D402 TFZGTR24B

R401 4.7K D401 D401A HSC119TRF-E R402 3K

3
C605 R614 100 /200V 330K R603 330K R604 330K T601 POWER TRANS R501 47/2W Q501 2SK3498 (SWITCHING) 3.9 3.6 BC601 WIRE 4 C606 470P /2KV 165.4 D G 0.1 S Q601 TK5A50D (SWITCHING) 3.9 C607 1200P 3.9 0 D607A OPEN Q602 2SC2120-Y SWITCHING CONTROL 0.4 R610 OPEN R608 1.2K R608A OPEN D605B OPEN D605 MM5Z4V3B C602 2200P/250V C501 0.1 D502 R502 UDZSNPTE-1730B 1.5M D501 R605 UDZSNPTE-1733B 330K 9 1 11 160.4 2 10

DRIVE 0.5 5 DRIVE 0 6 GND 0 7 DRIVE 0 8 0 9 DRIVE

D653 SK210TD C654 470/25V C655 470/25V D654 1ZB20BB D654A OPEN C658 OPEN Q650 KTC3875S -Y-RTK/P (RESET) 0 R650 5.6K R650A OPEN R1008 1.1K R1009 16K

DRIVE 1.3 10 OVP 1.3 11 ISET 1.0 12 RT R1007 100K

C1019 4.7 R1016 10K C1022 470P C1020 R1017 OPEN 100K R1501 0 R1503 0 R1502 OPEN R1504 OPEN R1020 0 R1021 0 CN1001 0.5 1 0.5 2 3 44.6 4 5 0.5 6 0.5 7 TO LCD PANEL ASSEMBLY ILED4 ILED3 NU VLED NU ILED1 ILED2

CONTROL LOGIC

5 R606A R607A OPEN OPEN C608 0.047 R606 270 R607 270 6

12

R651 D656 0 RS1BJTB C656 1/50V

D657 MM5Z20B D657B OPEN

R652 12K

D666

3.4 0 D405 OPEN D405A OPEN D406 OPEN D406A OPEN

R678 100K D666A HSC119TRF-E

R653 43K D610A HSC119TRF-E R613A OPEN D610 R613 220 IC601 TLP781F(D4-FUNBLLF) ERROR VOLTAGE DET 15.7 20.7 0.4 2 3 1 4 19.6 R655A OPEN R655 180 R657 3.9K R657A OPEN C660 0.1 D661B D661 PZU5.6B2.115 5V6BSB-T26 D660 SL431A-AT R661 3.3K R658 2.7K R654A OPEN R654 180 C659 OPEN R659 22K R660 2.7K Q655 OPEN R676 OPEN R673 5.6 C664 OPEN 21.0 4.0 3.4 Q656 2SC2120-Y R662 (+3.3V REG.) 1.5K R680 10K R665 10K R666 OPEN R667 OPEN C662 OPEN R675 OPEN Q654 OPEN R670A OPEN R670 180 R671A OPEN R671 180 R672A OPEN R672 180 D662 SL431A-AT R677 10K D663 OPEN D663A OPEN C665 R682 0.1 0

C632 OPEN C631 OPEN C630 OPEN

D607 1ZB27BB

D658A OPEN

D658 OPEN

D609A HSC119TRF-E D609 D608A OPEN D608 1ZB36BB R611 0.68 /2W C609 0.082 R612 2.2K R612A OPEN C610 1000P

C633 OPEN C661 OPEN JS632

C635 OPEN

C636 OPEN

JS631 OPEN

C663 C637 100/10V OPEN

C638 OPEN C639 OPEN

15.0 BC602 BEAD 0 BC603 OPEN

Q652 KTC3875S-Y-RTK/P (SWITCHING) R664 10K 0.1 R663 47K

R681 10K

0.1 0.7 Q653 KTC3875S-Y-RTK/P (SWITCHING) 0

R669 10K R668 22K

HOT

COLD

CN631 23 3.3 22 3.3 21 3.3 20 0 19 18 3.3 17 3.3 16 0 15 0 14 3.3 13 0 12 14.2 11 14.2 10 0 9 21.0 8 21.0 7 0 6 0 5 0 4 0 3 21.0 2 21.0 1

TO DIGITAL MAIN CBA UNIT CN3601 or CN3701 VCOM-PWM(NU) BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 PROTECT1 P-ON-H1(NU) P-ON-H2 RESET OE2(NU) GND AL+3.3V GND AMP+13V AMP+13V GND P-ON+21V P-ON+21V GND GND GND GND P-ON+21V P-ON+21V

UNLESS OTHERWISE SPECIFIED: DIODES ARE HSS4148TE-E.

C
10-3

G
PL12.0SCP

Function Schematic Diagram

R4052 6.8K

R4063 OPEN R4062 0

C4054 0.1

R4061 OPEN

VCC GND VOUT

3
R4051 56 D4053 OPEN C4051 10

RS4051 GP1USC32XP (REMOTE SENSOR)

D4051 SML813WBC8W1 POWER

R4055 OPEN IC4051 OPEN 1 OUT NU 6 C4058 OPEN R4057 OPEN D4052 OPEN C4057 OPEN 2 GND 3 VCC NU 5 NU 4 R4058 OPEN

R4059 OPEN

3 2 1

CN4001 3.3 1 5.0 2 0 3 2.0 4 3.3 5 3.3 6 0 7 3.3 8 3.3 9

TO DIGITAL MAIN CBA UNIT CN3101 or CN3105 AL+3.3V P-ON+5V LIGHT LED1 REMOTE KEY-IN1 GND SCL SDA

R4054 1K C4056 10 C4052 1000P C4055 OPEN

R4053 2.2K

R4056 OPEN

C4053 0.1

D4001 MM5Z5V6B

C4003 OPEN

POWER CH UP CH DOWN

R4001 560 R4003 560 R4005 560 0 18


CH DOWN

CH UP

POWER

2
SOURCE C4001 1 MENU VOL UP VOL DOWN

0 17

0 16

0 15
GND

0 14
GND

3.3 13 12 3.3 MENU 11 3.3 NU 10 0 GND 9 0 GND 8 0

R4008 18K R4009 8.2K

R4007 560

0 19 3.3 20 VDD

SOURCE

VOL DOWN VOL UP

R4006 560 R4004 560 R4002 560

0 21 MENU 0 22 VOL UP 0 23 VOL DOWN


CH DOWN SOURCE POWER CH UP

R4017 OPEN R4010 4.7K

SCL

1 2 3 4 5 6 3.3 3.3 3.3 3.3 3.3 3.3 IC4001 CY8C20336A -24LQXIT (TOUCH SENSOR)

SDA

1.0 24 NU C4002 2200P

NU 7 0

R4011 2.7K R4012 2.2K R4014 2.2K R4013 100 R4021 10 R4022 10 D4003 MM5Z5V6B D4004 MM5Z5V6B D4002 OPEN C4006 OPEN

1
FUNCTION CBA

C
10-4

D
PL12.0SCF

Digital Main 1 Schematic Diagram [TYPE A]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/5) ~ IC3005 (5/5) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 4 PROTECT3 VCOM-PWM OE2

DIGITAL MAIN CBA UNIT


D3008 HSC119 R3045 OPEN C3110 OPEN C3045 OPEN C3047 OPEN C3052 OPEN R3081 OPEN Q3207 AP2301GN-HF (SW+5V) S D R3044 OPEN R3047 OPEN R3046 OPEN C3058 OPEN C3057 R3039 OPEN OPEN R3242 47K C3241 0.47 G R3244 33K Q3206 2SC4081UBTLQ (SWITCHING) R3085 OPEN R3038 OPEN C3512 OPEN R3035 OPEN R3524 OPEN IC3010 OPEN 1 BST C3061 OPEN 2 VIN 3 SW 4 GND R3604 OPEN C3608 OPEN L3004 OPEN SS 8 EN 7 COMP 6 FB 5 R3071 OPEN C3068 OPEN R3075 OPEN R3074 OPEN C3077 OPEN R3080 OPEN R3037 OPEN C3100 OPEN C3093 OPEN R3078 OPEN C3089 OPEN R3245 470 C3078 OPEN C3514 OPEN D3004 OPEN C3513 OPEN CONTINUE DIGITAL 4 P-ON+5V P-ON+21V P-ON+3.3V CN3006 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN3001 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (NO CONNECTION) LCD+21V LCD+21V GND VCOM-PWM PWR-CTRL P-ON+3.3V GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCLK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE OE2 STV (NO CONNECTION) LCD+21V LCD+21V LCD+21V GND VCOM-PWM PWR-CTRL P-ON+3.3V GND LLV0(+) LLV0(-) LLV1(+) LLV1(-) LLV2(+) LLV2(-) GND LLVCLK(+) LLVCLK(-) GND LLV3(+) LLV3(-) LLV4(+) LLV4(-) LLV5(+) LLV5(-) GND TP POL CPV OE OE2 STV

CONTINUE DIGITAL 3 CELL-PWR-CTRL

0 OPEN 0 0

R3048 OPEN

C3000 OPEN

Q3007 OPEN R3240 10K C3240 R3241 OPEN OPEN

TO LCD PANEL ASSEMBLY OD0(-) OD0(+) OD1(-) OD1(+) OD2(-) OD2(+) GND OC(-) OC(+) OD3(-) OD3(+) ED0(-) ED0(+) GND ED1(-) ED1(+) ED2(-) ED2(+) GND EC(-) EC(+) GND ED3(-) ED3(+) GND GND LCD+5V LCD+5V LCD+5V LCD+5V LCD+5V

R3160 R3162 R3163 R3164

CN3011 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C3167 1000P

R3121 R3122 R3123 R3124 R3125 R3126 R3127 R3128 R3129 R3130

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

D3010 OPEN D3009 OPEN C3098 OPEN R3076 OPEN

C3054 OPEN

R3028 OPEN R3090 OPEN

R3073 OPEN

*1 IC3005(1/5) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER R16 R15 P14 P13 N16 N15 P16 P15 T16 T15 R14 T14 R13 T13

C3166 4.7

C3168 OPEN

LVDS TX

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

OPEN OPEN OPEN OPEN OPEN OPEN

R3088 9.1K

C3368 C3365 C3364 C3363 C3369 C3367 C3372 C3371 C3370 C3366

C
10-5

C3161 C3162 C3163 C3164 C3169 C3165

R3117 R3118 R3119 R3120 R3132 R3041

OPEN OPEN OPEN OPEN OPEN OPEN

LO-2N M16 LO-CP M13 TO DIGITAL LO-3N N14 MAIN 2 IC3005(2/5) LO-3P N13 TP L13 POL M15 CPV L16 OE L15 OE2 L14 STV M14 NU K15

C3355 C3356 C3349 C3350 C3351 C3352 C3353 C3354 C3357 C3358 C3359 C3360 C3361 C3362

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

R3512 R3513 R3518 R3519 R3521 R3520

OPEN OPEN OPEN OPEN OPEN OPEN

R3152 OPEN

F
PL12.0SCAD1

Digital Main 2 Schematic Diagram [TYPE A]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/5) ~ IC3005 (5/5) in this Digital Main Schematic Diagram Section.

TU3901 TUNER UNIT


DIF-OUT1 DIF-OUT2

TU3902 OPEN
DIF-OUT1 DIF-OUT2

DIGITAL MAIN CBA UNIT


IF-AGC SCL

IF-AGC

+3.3V

+3.3V

GND

SDA

SCL

GND

SDA

IC3013 74LVC1G126GW (BUFFER GATE) 1 VCC 5 2 3 GND 4 C3214 0.1 Q3301 2SK3018 (BUFFER) Q3302 2SK3018 (BUFFER)

4
C3901 D3901 OPEN MM5Z5V6B C3903 0.1 C3902 0.1 C3905 10 C3906 OPEN C3904 OPEN L3913 2.2uH C3934 OPEN C3909 OPEN D3903 MM5Z5V6B C3910 10P D3904 MM5Z5V6B D3902 MM5Z5V6B C3908 OPEN R3204 2.7K R3203 2.7K

CONTINUE DIGITAL 5 VGA-SDA VGA-SCL

IC3014 74LVC1G126GW (BUFFER GATE) 1 VCC 5 2 3 GND 4

CONTINUE DIGITAL 4 P-ON+3.3V P-ON+5V

R3298 10

R3296 10 R3326 4.7K R3321 4.7K JK3001 PC-RGB-IN

*1 IC3005(2/5) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

TO DIGITAL MAIN 5 IC3005(5/5)

SCL R12 SDA T12 B12 DEMODULATOR /MPEG DECODER A12

R3206 47 R3207 47 C3176 33P C3175 33P C3173 33P C3172 33P R3251 10 R3343 10 R3250 10 R3339 10 C3177 1000P

D3041 OPEN

D3054 OPEN

11 12 13

6 7 8 9

1 2 3 4 5

R3358 10K R3347 10K R3301 OPEN R3302 OPEN

D3050 OPEN D3045 OPEN D3049 OPEN D3053 OPEN D3055 OPEN

14

IF-AGC A16

R3202 2.7K R3205 18K

R3194 1K C3178 0.1

15 10

HSYNC A14 VSYNC B14 A9 C7 C11 SW C10 C9 D8 B11 A10 C8 D9 B9

C3194 0.1 C3195 0.1 C3196 0.1 C3198 C3199 C3200 C3201 0.01 0.1 0.1 0.1 C3291 33P C3292 33P C3293 33P

R3285 47 R3286 47 R3284 47 R3356 75 R3327 10 R3328 10 R3329 10 C3289 33P C3288 33P C3287 33P R3377 75 R3364 75

R3303 OPEN

CONTINUE DIGITAL 3 COMP-DET

A/D CONVERTER

2
DIGITAL SIGNAL PROCESS

NU NU NU NU TO DIGITAL MAIN 3 IC3005(3/5) TO DIGITAL MAIN 3 IC3005(3/5)

JK3702 R3711 7.5K C3717 OPEN C3714 OPEN C3708 0.1 C3701 OPEN C3702 OPEN Q3701 2SC4081UBTLQ (BUFFER) R3709 220 R3708 110 C3706 1 C3715 OPEN C3709 100P R3704 100K R3705 100K C3703 OPEN R3701 75 R3702 75 R3703 75 COMPONENT -Y/VIDEO-IN COMPONENT -Pb-IN COMPONENT -Pr-IN JK3701 DIGITAL AUDIO-OUT (COAXIAL) AUDIO(L)-IN

R3710 100 C3707 1 C3197 OPEN C3335 2.2 C3716 OPEN R3712 10K

TO DIGITAL TO DIGITAL MAIN 1 MAIN 5 IC3005(5/5) IC3005(1/5)

NU B10 NU A11 NU D10

C3285 0.1 C3286 0.1 C3336 1

AUDIO(R)-IN CONTINUE DIGITAL 5 SCL SDA AUDIO(L)-IN AUDIO(R)-IN CONTINUE DIGITAL 5 SPDIF

I
10-6

L
PL12.0SCAD2

Digital Main 3 Schematic Diagram [TYPE A]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/5) ~ IC3005 (5/5) in this Digital Main Schematic Diagram Section.

C3009 OPEN R3064 100 R3065 100 C3050 OPEN C3051 0.1

*1 IC3005(3/5) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER M5 SD-VREF0 N3 GND XIN25 H15 XOUT25 H16 R8 N8 P7 R6 P6 N7 T5 P8 P4 T3 R4 T2 P3 T4 R3 N4 T6 R5 T7 R7 N5 P5 SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 SD-UDM SD-LDM SD-UDQSN SD-UDQS SD-LDQSN SD-LDQS ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS TO DIGITAL MAIN 2 IC3005(2/5) F15 F16 E16 E15 D16 D15 E14 R3522 10K R3223 1K X3001 25MHz

C3184 16P

4
IC3002 K4T51163QI-HCF7 (DDR2 SDRAM) C3029 C3030 C3031 C3032 C3033 C3034 C3035 C3037 C3038 C3039 C3040 C3041 C3140 0.1 OPEN OPEN OPEN OPEN 0.1 0.1 0.1 OPEN OPEN 0.1 0.1 0.1 *A VDD VREF J2 C3010 0.1 E2 A2 R8 R7 R3 1-O3 2-O3 3-O3 SD-DQ15 SD-DQ10 SD-DQ12 SD-DQ11 SD-DQ13 SD-DQ14 SD-DQ9 SD-DQ8 4-O3 5-O3 6-O3 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 B7 A8 B3 B9 B1 D9 D1 D3 D7 C2 C8 F7 E8 F3 F9 F1 H9 H1 H3 H7 G2 G8 NU NU NU NU NU UDQS UDQS/NU UDM DQ15 DQ10 DQ12 DQ11 DQ13 DQ14 DQ9 DQ8 LDQS LDQS/NU LDM DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 CKE CK CK CS RAS CAS WE BA2/NU BA1 BA0 A12 A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 ODT K2 J8 K8 L8 K7 L7 K3 L1 L3 L2 R2 P7 M2 P3 P8 P2 N7 N3 N8 N2 M7 M3 M8 K9

C3183 16P

SD-DQ15 SD-DQ14 SD-DQ13 SD-DQ12 SD-DQ11 SD-DQ10 SD-DQ9 SD-DQ8 SD-DQ7 SD-DQ6 SD-DQ5 SD-DQ4 SD-DQ3 SD-DQ2 SD-DQ1 SD-DQ0 3-M3 6-M3 2-M3 1-M3 5-M3 4-M3 R3087 R3082 R3034 R3016 R3084 R3021 R3083 R3070 R3030 15 6.8 6.8 15 15 15 15 150 15x4

CN3012 1 2 3 4 5 6 7 8 9 10 R3395 4.7K CN3010 1 2 3 C3253 4 OPEN

(NO CONNECTION) AL+3.3V GND ASEBRKAK-N ASEMD0 TRST-N TCK TDI TDO TMS CPU-RESET-N (NO CONNECTION) P-ON+5V UART0-TX UART0-RX GND

TXD0 G15 RXD0 G16

R3468 100 R3469 100 C3254 OPEN C3255 OPEN R3396 4.7K

R3049 100

BACKLIGHT-ADJ F3 VCOM-PWM F2 GND J14

R3516 100 R3517 OPEN

CONTINUE DIGITAL 2 COMP-DET

CONTINUE DIGITAL 1 CELL-PWR-CTRL R3511 22 R5129 R3211 R3233 R3531 R3188 R3503 10K OPEN 100 OPEN OPEN 22 CONTINUE DIGITAL 4 CELL-PWR-CTRL GPY10 CPU-RESET-N P-ON-H2 P-ON-H1 BACKLIGHT-ADJ BACKLIGHT-SW VCOM-PWM

VSS *B

R3031

15x4

2
IC3006 S25FL032P0XMFI010 (MEMORY) 1 CS 2 SO 3 WP 4 GND VCC 8 NU 7 SCK 6 SI 5

*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1 *B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9

R3032

15x4

R3033 R3102 10K R3107 10K C3073 0.1 R3089 R3092 R3093 R3094 R3095

15x4

L4 R1 R2 L3 H2 H1 N2 H4 M2 N1 M3 P1 K2 L2 M1 L1 J2 K3 K1 J1 J3 H3 J4 K4 P12 R11 P11 T11 T9 R9 R10 T10 P10

SD-WE SD-CLKN SD-CLK SD-CKE SD-A8 SD-A4 SD-BA0 NU SD-A12 SD-A7 SD-A3 SD-BA2 SD-ODT SD-A9 SD-A5 SD-A1 SD-A11 SD-A6 SD-A2 SD-A0 SD-RAS SD-CAS SD-A10 SD-BA1 CS SOUT SIN SCLK VBUS-EN VBUS-ST USBDP USBDN NU

CELL-PWR-CTRL D1 GPY10 E13 P-ON-H2 B16 P-ON-H1 G13 BACKLIGHT-SW E2

TO DIGITAL MAIN 2 IC3005(2/5) LED1 D14 AUDIO-MUTE C1 REMOTE C14

R3510 22K R3515 4.7K R3217 22 R3213 22 R3234 OPEN

CONTINUE DIGITAL 5 SW-EN LED1 AUDIO-MUTE REMOTE CPU-RESET-N BACKLIGHT-SW CONTINUE DIGITAL 4 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V CONTINUE DIGITAL 5 P-ON-H2 HPD-SINK

COMP-DET N12

R3215

22

R3201 33K

R3479 10K C3246 1 D3052 OPEN C3348 220/6.3V

47 47 47 47 22

NU H14

C3072 10 C3071 OPEN

(USB JACK) BUS-POWER USBDN USBDP GND

CN3009 1 2 3 4

R3099 5.6K IC3019 BD2224G-TR (HIGH SIDE SW) 1 VIN VOUT 5 C3327 1 R3480 10K 2 GND 3 /EN /OC 4

L3025 EXC24CG900U

DIGITAL MAIN CBA UNIT

O
10-7

R
PL12.0SCAD3

Digital Main 4 Schematic Diagram [TYPE A]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/5) ~ IC3005 (5/5) in this Digital Main Schematic Diagram Section.

R3218 OPEN *1 IC3005(4/5) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER VCC33STB F12 VCC33STB G12 C3160 0.1 C3182 OPEN G VDD12STB E12 L3030 0 C3181 0.1 VDD12 *C C3123 1 C3130 OPEN AVDD12 M10 C3135 0.1 AVDD12 E8 AVDD12 F8 AVDD12 F9 C3118 10 C3136 1 C3137 OPEN C3155 OPEN L3021 BEAD C3156 OPEN R3228 6.8K C3139 0.1 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 VCCQ18 H5 J5 M4 T1 M6 N6 M7 M8 C3326 10 C3322 10 C3036 1 C3325 OPEN C3321 OPEN C3141 1 C3324 OPEN C3320 10 C3142 OPEN C3343 10 C3319 10 C3143 1 C3266 C3264 OPEN OPEN C3114 OPEN C3144 1 C3318 10 C3145 1 C3081 OPEN L3019 BEAD AVDD33 AVDD33 AVDD33 AVDD33 E10 C2 C3 E11 C3148 1 C3147 OPEN C3149 10 C3150 1 C3117 OPEN C3091 OPEN R3141 OPEN D3113 MM5Z5V6B L3026 BEAD C3085 0.1 C3082 OPEN IC3008 MP2305SDS-LF-Z (+1.2V REG.) 1 BST 2 VIN 3 SW 4 GND L3009 22uH R3602 OPEN C3606 OPEN C3094 330/4V C3067 OPEN C3097 10 SS 8 EN 7 COMP 6 FB 5 C3122 OPEN C3083 0.015 R3134 10K R3137 5.6K C3088 0.015 C3096 10 R3149 3.9K R3145 1.2K R3143 15K C3026 OPEN C3025 OPEN IC3003 MP2305SDS-LF-Z (+5V REG.) C3095 OPEN R3054 OPEN C3042 0.1 1 BST 2 VIN 3 SW 4 GND L3005 22uH R3603 OPEN C3607 OPEN C3053 220/6.3V C3074 10 SS 8 EN 7 COMP 6 FB 5 R3005 5.6K C3043 0.015 C3056 10 R3012 33K R3007 12K R3006 10K C3104 OPEN C3022 OPEN C3105 4.7 R3108 47K D3112 MM5Z12B R3140 20K C3028 0.047 R3098 0 C3121 OPEN R3112 10K R3115 Q3103 OPEN 2SA1576UBTLQ (SWITCHING) C3238 R3139 OPEN 1K R3101 1K C3601 OPEN C3602 OPEN C3015 OPEN C3604 10 C3016 OPEN C3603 1 D3607 OPEN D3602 MM5Z5V6B D3107 HSC119 Q3009 2SC4081UBTLQ (SWITCHING) C3099 OPEN C3080 OPEN C3103 4.7 R3133 10K C3092 OPEN C3090 1 R3142 OPEN L3002 33uH C3065 OPEN R3601 OPEN C3605 OPEN C3020 330/4V C3101 OPEN C3021 10 R3057 OPEN C3014 0.1 C3102 4.7 C3007 OPEN IC3001 MP2305SDS-LF-Z (+3.3V REG.) 1 BST 2 VIN 3 SW 4 GND SS 8 EN 7 COMP 6 FB 5 C3119 OPEN R3001 9.1K C3017 3300P C3059 10 R3004 C3060 33K OPEN R3003 6.2K D3005 PTZTE255.1B D3011 OPEN D3012 OPEN C3002 OPEN C3013 0.047 C3012 OPEN R3091 0 C3001 OPEN C3109 OPEN C3112 OPEN R3014 270 C3237 R3227 OPEN 1.2K Q3011 2SC4081UBTLQ (SWITCHING) D3106 HSC119 C3079 220/6.3V C3076 OPEN R3077 10K R3079 10K C3124 OPEN C3134 10 C3128 1 C3132 OPEN C3133 10 C3126 OPEN D S R3221 100 R3222 10K L3027 BEAD R3464 OPEN Q3006 2SA1576UBTLQ (SWITCHING) R3106 47K R3105 10K R3100 22K Q3101 2SC4081UBTLQ (SWITCHING) D3105 OPEN D3103 HSC119 R3424 100 R3036 100

CONTINUE DIGITAL 3 P-ON+1.8V P-ON+3.3V AL+3.3V P-ON+5V

Q3013 SSM3K309T (SW+12V) Q3005 2SC4081UBTLQ (SWITCHING) D3101 HSC119 D3102 HSC119

C3265 R3138 10 OPEN R3423 R3097 47K 2.2K D3104 HSC119

IC3004 BD00IC0WEFJ (+1.2V REG.) 1 VOUT 2 FB R3061 10K R3060 2.7K R3059 2.7K C3263 OPEN C3019 0.022 R3062 1.8K C3086 10 L3003 BLM21PG221SN1D IC3007 BD00IC0WEFJ (+1.8V REG.) 1 VOUT 2 FB R3111 10K R3110 10K R3109 3.3K C3084 OPEN C3075 0.022 R3103 1.8K C3087 10 3 GND 4 NU VCC 8 NU 7 NU 6 EN 5 C3069 10 C3070 OPEN C3111 OPEN C3066 OPEN 3 GND 4 NU VCC 8 NU 7 NU 6 EN 5 C3024 10 C3108 OPEN C3027 OPEN CONTINUE DIGITAL 2 P-ON+3.3V P-ON+5V CONTINUE DIGITAL 1 P-ON+5V P-ON+21V P-ON+3.3V CONTINUE DIGITAL 5 RESET PROTECT1 PROTECT3 CONTINUE DIGITAL 1 PROTECT3 VCOM-PWM OE2 CONTINUE DIGITAL 5 CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V P-ON+3.3V CONTINUE DIGITAL 3 CELL-PWR-CTRL GPY10 CPU-RESET-N P-ON-H2 P-ON-H1 BACKLIGHT-ADJ BACKLIGHT-SW VCOM-PWM

D3115 HSC119

R3086 4.7K

C3049 R3043 OPEN 180 Q3003 2SC4081UBTLQ (SWITCHING) Q3004 2SC4081UBTLQ (SWITCHING)

C3131 1

VDDCLK G11

R3042 OPEN

AVDD33 E6 C3151 1 VCCQ33 VCCQ33 VCCQ33 VCCQ33 VCCQ33 AVDD33 G4 F5 L12 K13 J12 N11 C3152 1 C3154 1 D3114 MM5Z5V6B

D3006 PTZTE255.1B

R3052 R3051 R3068 R3013 R3009 R3011 R3008 R3053

270 OPEN OPEN 100 100 100 OPEN OPEN

AVDD33 D6 L3006 BEAD

R3136 OPEN

C3157 1

C3159 1

R3002 15K

VSS *D *C:G5,G6,H6,J7,J11,J13,K6,K7, K11,L8,L9,M9,N9,P9,M11. *D:D2~D5,D12,E3~E5,E7,E9,F4,F6, F7,F10,F11,G7~G10,H7~H13,J6, J8~J10,K5,K8~K10,K12,L5~L7, L10,L11,P2,T8

Q3102 2SC4081UBTLQ (SWITCHING)

R3113 10K

C3107 R3104 1K 1 R3072 100

R3114 47K D3007 OPEN

1
DIGITAL MAIN CBA UNIT

C3146 OPEN

C3138 OPEN

C3153 OPEN

U
10-8

C3055 C3063 C3062 C3048 C3008 C3004 C3006 C3003 C3064

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

C3044 OPEN

C3011 OPEN

C3046 OPEN

CN3701 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

TO POWER SUPPLY CBA CN631 VCOM-PWM(NU) BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 PROTECT1 P-ON-H1(NU) P-ON-H2 RESET OE2(NU) GND AL+3.3V GND AMP+13V AMP+13V GND P-ON+21V P-ON+21V GND GND GND GND P-ON+21V P-ON+21V

X
PL12.0SCAD4

Digital Main 5 Schematic Diagram [TYPE A]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3005. IC3005 is divided into five and shown as IC3005 (1/5) ~ IC3005 (5/5) in this Digital Main Schematic Diagram Section.
CONTINUE DIGITAL 4 CHECK+1.8V AL+3.3V P-ON+5V P-ON+3.3V(1) AMP+13V P-ON+3.3V R3537 OPEN R3312 10K

*1 IC3005(5/5) R8A05011BG-U0 DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER D13 NU EXT-RES PLL-XFC-A PLL-XFC-P HDMI-CEC VGA-SDA VGA-SCL C4 B5 A5 B15 F14 G14 B1 A1 B2 A2 B3 A3 B4 A4

R3270 C3187 2.2K 2.2 R3236 560 C3185 0.01 C3186 4700P R3271 C3188 2200P 3K

R3193 4.7K Q3014 2SK3018T106 (BUFFER) R3405 100 R3415 82K D3057 RB751S-40 C3271 OPEN

R3192 4.7K

CONTINUE DIGITAL 2 VGA-SDA VGA-SCL HDMICONNECTOR TMDS-D2(+) D-SHIELD0 TMDS-D2(-) TMDS-D1(+) D-SHIELD1 TMDS-D1(-) TMDS-D0(+) D-SHIELD2 TMDS-D0(-) TMDS-CLOCK(+) C-SHIELD0 TMDS-CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT

C3272 OPEN JK3003 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

CONTINUE DIGITAL 3 SW-EN LED1 AUDIO-MUTE REMOTE CPU-RESET-N BACKLIGHT-SW TO FUNCTION CBA CN4001 SDA SCL GND KEY-IN1 REMOTE LED1 LIGHT P-ON+5V AL+3.3V CN3101 1 2 3 4 5 6 7 8 9

R3532 OPEN

R3535 OPEN

Q3530 OPEN

R3533 OPEN Q3502 2SA1576UBTLQ (LED DRIVE)

R3237 27K

R3534 OPEN

R3558 OPEN

R3559 10K VIDEO DECODER HDMI I/F

R3561 10

R3552 100 Q3531 OPEN

R3560 100K

R3551 100

R3555 OPEN C3557 OPEN Q3501 2SC4081UBTLQ (LED DRIVE)

R3318 22K R3317 10K R3319 10K

C3559 OPEN

C3231 0.22

R3320 OPEN C3330 OPEN C3329 0.01 D3116 OPEN C3323 OPEN R3314 R3315 R3316 R3208 22 OPEN 22 0 A15 B13 A13 C13 C12

TO DIGITAL MAIN 2 IC3005(2/5) HDMI-SCL C16 HDMI-SDA C15 HPD-SINK F13

R3487 4.7K R3514 100 R5128 OPEN Q3201 2SK3018T106 (BUFFER) R3022 10K R3023 18K AUDIO DECODER R3019 10K R3020 10K Q3203 2SA1576UBTLQ (SWITCHING) R3488 4.7K Q3202 2SK3018T106 (BUFFER) R3015 10K

R3183 OPEN C3558 OPEN

Q3010 OPEN

R3536 0 C3555 OPEN C3554 1

C3553 100P

C3556 OPEN

R3212 47K

R3214 47K C3005 R3024 47K 0.1 R3010 1K

R3185 OPEN R3184 OPEN R3186 OPEN

PWR M12 KEY-IN1 PROTECT3 LIGHT-SENS PROTECT1 LPF

CONTINUE DIGITAL 4 RESET PROTECT1 PROTECT3 CONTINUE DIGITAL 2 SCL SDA AUDIO(L)-IN AUDIO(R)-IN CONTINUE DIGITAL 2 SPDIF R3556 10

C3551 33P C3552 33P

R3553 100

D3501 MM5Z5V6B

R3018 10K R3017 10K

Q3205 2SC4081UBTLQ (SWITCHING) Q3204 2SC4081UBTLQ (SWITCHING)

R3557 10

C3328 OPEN R5104 OPEN

CONTINUE DIGITAL 3 P-ON-H2 HPD-SINK

R3335 18K R3336 18K

R3502 C3229 R3501 C3227 C3233 R3500 C3232 R3499

OPEN OPEN OPEN OPEN 1000P OPEN 1000P OPEN

C3217 C3218 C3223 C3224 R3209 R3340 C3219 C3220 C3216

10 10 10 10 100 10K 10 10 10

R3191 100 IC3009 PST8429UR (RESET) 1 GND OUT 4 2 VDD D3108 OPEN D3805 HSC119 R3811 2.2K D3806 MM5Z6V2B C3810 100/25V R3810 R3809 20K 82K R3816 D3802 15K HSC119 R3806 10K R3812 20K R3813 82K Q3803 2SA1576UBTLQ (SWITCHING) R3828 10K R3818 4.7K C3809 0.1 R3820 OPEN R3819 3.3K R3826 47K C3816 0.1 C3817 OPEN R3817 15K C3813 1000P C3811 100/16V C3808 1 C3824 10 C3823 10 C3807 1 C3812 1000P D3807 D3808 HSC119 HSC119 R3831 2.7K R3832 2.7K IC3801 TDA1517P/N3 (AUDIO AMP) 1 2 GND 3 4 5 GND 6 7 VCC 8 9 MUTE CONTROL DRIVE RIPPLE FILTER DRIVE C3825 10 C3826 10 C3106 1 C3252 OPEN CD 3 C3113 0.033 D3111 MM5Z5V6B R3182 56K C3116 1000P D3109 OPEN D3110 OPEN

A8 B8 B7 A7 N10 D11 D7 C6 C5 B6 A6 J15

R5124 OPEN AUDIO I/F

R5113 OPEN R5112 OPEN D5107 OPEN

Q5104 OPEN

Q5105 OPEN R5114 OPEN

R5106 OPEN R5110 OPEN Q5103 OPEN

R5111 OPEN

NU NU NU NU NU NU RESET

R5109 OPEN SW-PU-CONT E1 TO DIGITAL FACTORY-SEL G1 MAIN 2 IC3005(2/5) R5121 OPEN R5125 OPEN R5127 OPEN R3216 100 R5103 OPEN R5119 OPEN Q5109 OPEN R3402 0 R5120 OPEN R5117 OPEN SM-CLK K16 R5122 OPEN C5104 OPEN Q5102 OPEN R5118 OPEN R5101 OPEN R5105 OPEN Q5108 OPEN R3401 0

R5107 OPEN

C5105 OPEN R5126 OPEN

R5123 OPEN C5106 OPEN

Q5110 OPEN

R3178 220

SM-MISO/FACTORY-RX J16 NU F1 NU G2 NU G3

IC5101 OPEN 1 OE VCC 5 2 A 3 GND R5108 OPEN L5102 OPEN L5103 OPEN
C5101 OPEN

C5103 OPEN

Y 4 R5115 OPEN R5102 OPEN L5101 OPEN

D5106 OPEN

NU 18 NU 17 NU 16 NU 15 NU 14 NU 13 NU 12 NU 11 NU 10 C3805 OPEN R3804 OPEN D3803 MM5Z20B C3803 100/25V C3815 100/25V C3821 100/25V C3804 100/25V C3806 OPEN R3805 OPEN D3804 MM5Z20B C3814 100/25V C3822 100/25V

SM-MOSI/FACTORY-TX K14

R3210 100 C5102 OPEN Q5106 OPEN R5116 OPEN Q5107 OPEN Q5101 OPEN

R3802 180 R3821 OPEN R3824 OPEN R3823 OPEN C3818 OPEN R3801 180 C3801 OPEN C3802 OPEN L3803 OPEN C3819 OPEN C3820 OPEN CN3801 1 2 3 4 SP3801 SPEAKER L-CH JK3703 HEADPHONE JACK

Q3802 OPEN

R3829 R3827 10K 10K Q3804 2SC4081UBTLQ (SWITCHING) R3830 OPEN

Q3801 2SC4081UBTLQ (AUDIO-MUTE) R3803 10K R3807 3.3K R3815 470 R3814 470

R3822 OPEN R3825 OPEN

R3808 300 D3801 HSC119

D5105 C5109 D5104 C5108 D5103 D5102 C5107 D5101

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

L5104 OPEN

CN5101 1 2 3 4 5 6

(NO CONNECTION) SM-CLK SM-MISO NU SM-MISI GND REMOTE

SP(L) GND GND SP(R)

DIGITAL MAIN CBA UNIT

SP3802 SPEAKER R-CH

AA
10-9

BB

CC

DD
PL12.0SCAD5

Digital Main 1 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.
CONTINUE DIGITAL 8 P-ON+12V/+21V P-ON+5V R3942 OPEN Q3905 OPEN 1 2 3 4 R3897 OPEN R3898 OPEN C3997 OPEN R3891 OPEN Q3904 OPEN 8 G R3550 OPEN C3951 OPEN R3936 OPEN C3950 OPEN R3899 OPEN 7 6 5 R3895 33K R3892 10K Q3902 2SC4081UBTLQ (SWITCHING) C3994 R3893 OPEN OPEN C3995 R3894 0.47 47K C3948 OPEN C3947 OPEN R3933 OPEN R3935 OPEN R3929 OPEN C3900 OPEN

(NO CONNECTION) CN3906 LCD+12V 1 LCD+12V 2 LCD+12V 3 LCD+12V 4 NU 5 GND 6 GND 7 GND 8 GND 9 GND 10 NU 11 NU 12 LV-ED3(+) 13 LV-ED3(-) 14 GND 15 LV-ECLK(+) 16 LV-ECLK(-) 17 GND 18 LV-ED2(+) 19 LV-ED2(-) 20 LV-ED1(+) 21 LV-ED1(-) 22 LV-ED0(+) 23 LV-ED0(-) 24 GND 25 GND 26 NU 27 NU 28 LV-OD3(+) 29 LV-OD3(-) 30 GND 31 LV-OCLK(+) 32 LV-OCLK(-) 33 GND 34 LV-OD2(+) 35 LV-OD2(-) 36 LV-OD1(+) 37 LV-OD1(-) 38 LV-OD0(+) 39 LV-OD0(-) 40 GND 41 NU 42 NU 43 NU 44 NU 45 NU 46 NU 47 NU 48 NU 49 NU 50 GND 51

R3890 R3889 R3870 R3862

TO LCD PANEL ASSEMBLY LCD+5V LCD+5V LCD+5V LCD+5V LCD+5V GND GND LV-ED3(+) LV-ED3(-) GND LV-ECLK(+) LV-ECLK(-) GND LV-ED2(+) LV-ED2(-) LV-ED1(+) LV-ED1(-) GND LV-ED0(+) LV-ED0(-) GND GND NU NU GND NU NU NU NU NU GND

CN3905 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
0 OPEN 0 0

D3905 OPEN IC3901 OPEN C3949 OPEN C3944 OPEN 1 BS 2 EN 3 SW 4 GND SS 8 EN 7 COMP 6 FB 5 R3938 OPEN L3901 OPEN R3927 OPEN C3970 OPEN R3953 R3951 R3950 R3949 R3948 R3947 R3946 R3943 R3918 R3917 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN C3953 OPEN R3939 OPEN C3956 OPEN

R3952 OPEN D3906 OPEN C3946 OPEN C3996 OPEN

Q3903 AP2301GN-HF (SW+5V) D S

R3934 OPEN R3931 OPEN

R3932 OPEN

C3957 OPEN

C3943 OPEN

Q3901 OPEN

R3937 OPEN

C3954 OPEN

D3901 C3952 OPEN OPEN

C3958 10

C3959 OPEN

R3911 470

R3912 OPEN

CN3904 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R3924 OPEN CN3903 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

(NO CONNECTION) LCD+21V LCD+21V GND VCOM-DC PWR-CTRL P-ON+3.3V GND LVDS-OD0(-) LVDS-OD0(+) LVDS-OD1(-) LVDS-OD1(+) LVDS-OD2(-) LVDS-OD2(+) GND LVDS-OCLK(-) LVDS-OCLK(+) GND LVDS-OD3(-) LVDS-OD3(+) LVDS-OD4(-) LVDS-OD4(+) LVDS-OD5(-) LVDS-OD5(+) GND TP POL CPV OE OE2 STV (NO CONNECTION) LCD+21V LCD+21V LCD+21V GND VCOM-DC PWR-CTRL P-ON+3.3V GND LVDS-OD0(-) LVDS-OD0(+) LVDS-OD1(-) LVDS-OD1(+) LVDS-OD2(-) LVDS-OD2(+) GND LVDS-OCLK(-) LVDS-OCLK(+) GND LVDS-OD3(-) LVDS-OD3(+) LVDS-OD4(-) LVDS-OD4(+) LVDS-OD5(-) LVDS-OD5(+) GND TP POL CPV OE OE2 STV

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

R3923 OPEN R3926 R3922 R3920 R3916 OPEN R3534 R3535 R3536 R3537 R3538 R3539 OPEN OPEN OPEN R3925 OPEN OPEN OPEN OPEN OPEN OPEN OPEN

*1 IC3101(1/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER R3888 R3887 R3971 R3970 OPEN OPEN 0 0 J6 J7 G2 G1 H4 G4 H1 G3 H2 H3 J2 J3
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

R3969 0 R3968 0 R3965 R3962 R3961 R3959 R3958 R3957 0 0 0 0 0 0

L4 L5 L3 L2 K5 K4 LVDS TX K3 L1 J5 J4 K1 K2 K7 K6 P7 A2 D4 B3 B2 D5 C3 R3944 OPEN C4 R3980 OPEN B1 G6 D3 R3901 10K R3945 OPEN

C3926 C3927 C3928 C3929 C3930 C3931 C3932 C3933 C3934 C3935 C3936 C3937 C3960 C3961

R3540 OPEN R3541 OPEN R3542 R3543 R3544 R3545 R3532 R3533 R3974 R3975 R3976 R3977 R3978 R3979 OPEN OPEN OPEN OPEN OPEN OPEN
OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN C3942 C3998 C3941 C3940 C3939 C3938

C3914 C3915 C3916 C3917 C3918 C3919 C3920 C3921 C3922 C3923 C3924 C3925

R3886 OPEN R3885 OPEN

F2 NU F3 NU TO DIGITAL MAIN 5 IC3101(5/8)

OPEN OPEN OPEN OPEN OPEN OPEN

NU TP POL CPV OE OE2 STV

NU NU BACKLIGHT-ADJ VCOM-PWM

R3884 R3928 R3883 R3882 R3881 R3880

R3930 OPEN

CONTINUE DIGITAL 3 FRC-CTRL3 CONTINUE DIGITAL 6 P-ON+3.3V

R3866 OPEN R3867 OPEN R3868 OPEN

C3903 OPEN

C3902 R3896 OPEN OPEN R3940 OPEN C3901 OPEN R3941 OPEN

R3900 OPEN R3903 OPEN R3905 OPEN C3909 OPEN R3902 OPEN C3910 OPEN D3902 1SS400

R3869 OPEN R3906 OPEN R3907 OPEN

CONTINUE DIGITAL 7 VCOM-PWM LCD-PON BACKLIGHT-ADJ OE2 PROTECT3

C3904 OPEN

DIGITAL MAIN CBA UNIT

C
10-10

F
PL12.0SCBD1

Digital Main 2 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

*1 IC3101(2/8) MN2WS0172A MAIN MICRO CONTROLLER /DIGITAL SIGNAL PROCESS MMVCAL M10 MMVREF0 G10 MMVREF1 G18 MMDQ0 MMDQ1 MMDQ2 MMDQ3 MMDQ4 MMDQ5 MMDQ6 MMDQ7 MMDQ8 MMDQ9 MMDQ10 MMDQ11 MMDQ12 MMDQ13 MMDQ14 MMDQ15 MMDQ16 MMDQ17 MMDQ18 MMDQ19 MMDQ20 MMDQ21 MMDQ22 MMDQ23 MMDQ24 MMDQ25 MMDQ26 MMDQ27 MMDQ28 MMDQ29 MMDQ30 MMDQ31 C6 D6 B6 A5 E6 B5 A4 C5 D8 C8 C9 B9 B10 C10 F8 E7 E17 F17 G17 F18 C18 B18 B19 C19 F16 E15 D16 C16 B15 C15 A14 B14 MMDQ0 MMDQ1 MMDQ2 MMDQ3 MMDQ4 MMDQ5 MMDQ6 MMDQ7 MMDQ8 MMDQ9 MMDQ10 MMDQ11 MMDQ12 MMDQ13 MMDQ14 MMDQ15 MMDQ16 MMDQ17 MMDQ18 MMDQ19 MMDQ20 MMDQ21 MMDQ22 MMDQ23 MMDQ24 MMDQ25 MMDQ26 MMDQ27 MMDQ28 MMDQ29 MMDQ30 MMDQ31 C3401 0.1 R3430 1K C3402 R3432 OPEN 270 C3403 OPEN R3429 1K R3431 270 R3433 270

DIGITAL MAIN CBA UNIT


CONTINUE DIGITAL 6 VCC+1.5V IC3401 K4B1G1646G-BCH9 (DDR3 SDRAM) MMA13 MMA12 MMA11 MMA10 MMA9 MMA8 MMA7 MMA6 MMA5 MMA4 MMA3 MMA2 MMA1 MMA0 T3 N7 R7 L7 R3 T8 R2 R8 P2 P8 N2 P3 P7 N3 M7 A13 A12/BC# A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NU VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 VDD8 VDD9 VDDQ1 VDDQ2 VDDQ3 VDDQ4 VDDQ5 VDDQ6 VDDQ7 VDDQ8 VDDQ9 B2 D9 G7 K2 K8 N1 N9 R1 R9 A1 A8 C1 C9 D2 E9 F1 H2 H9 R3435 270 VREFCA M8 R3436 270 VREFDQ H1 VSS1 VSS2 VSS3 VSS4 VSS5 VSS6 VSS7 VSS8 VSS9 VSS10 VSS11 VSS12 VSSQ1 VSSQ2 VSSQ3 VSSQ4 VSSQ5 VSSQ6 VSSQ7 VSSQ8 VSSQ9 A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 B1 B9 D1 D8 E2 E8 F9 G1 G9 R3437 220 MMDQ28 MMDQ24 MMDQ27 MMDQ30 MMDQ29 MMDQ25 MMDQ31 MMDQ26 MMDQ16 MMDQ23 MMDQ18 MMDQ22 MMDQ17 MMDQ19 MMDQ21 MMDQ20 C3413 0.1 C3429 0.1 MMA13 MMA12 MMA11 MMA10 MMA9 MMA8 MMA7 MMA6 MMA5 MMA4 MMA3 MMA2 MMA1 MMA0 T3 N7 R7 L7 R3 T8 R2 R8 P2 P8 N2 P3 P7 N3 M7 IC3402 K4B1G1646G-BCH9 (DDR3 SDRAM) A13 A12/BC# A11 A10/AP A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NU VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 VDD7 VDD8 VDD9 VDDQ1 VDDQ2 VDDQ3 VDDQ4 VDDQ5 VDDQ6 VDDQ7 VDDQ8 VDDQ9 B2 D9 G7 K2 K8 N1 N9 R1 R9 A1 A8 C1 C9 D2 E9 F1 H2 H9 R3439 270 VREFCA M8 R3440 270 VREFDQ H1 VSS1 VSS2 VSS3 VSS4 VSS5 VSS6 VSS7 VSS8 VSS9 VSS10 VSS11 VSS12 VSSQ1 VSSQ2 VSSQ3 VSSQ4 VSSQ5 VSSQ6 VSSQ7 VSSQ8 VSSQ9 A9 B3 E1 G8 J2 J8 M1 M9 P1 P9 T1 T9 B1 B9 D1 D8 E2 E8 F9 G1 G9 R3441 220 C3423 0.1 C3430 0.1

R3434 270

C3404 10 C3408 0.1 C3412 0.1

C3405 0.1 C3409 0.1 C3431 10

C3406 0.1 C3410 0.1

C3407 0.1 C3411 0.1

C3414 10 C3418 0.1 C3422 0.1

C3415 0.1 C3419 0.1 C3432 10

C3416 0.1 C3420 0.1

C3417 0.1 C3421 0.1

C7 B7 F3 G3 D3 E7 MMDQ1 MMDQ3 MMDQ2 MMDQ5 MMDQ0 MMDQ7 MMDQ4 MMDQ6 MMDQ13 MMDQ15 MMDQ11 MMDQ14 MMDQ9 MMDQ8 MMDQ10 MMDQ12 A3 B8 A2 A7 C2 C8 C3 D7 H7 G2 H8 H3 F8 F2 F7 E3

DQSU DQSU# DQSL DQSL# DMU DML DQU7 DQU6 DQU5 DQU4 DQU3 DQU2 DQU1 DQU0 DQL7 DQL6 DQL5 DQL4 DQL3 DQL2 DQL1 DQL0

C7 B7 F3 G3 D3 E7 A3 B8 A2 A7 C2 C8 C3 D7 H7 G2 H8 H3 F8 F2 F7 E3

DQSU DQSU# DQSL DQSL# DMU DML DQU7 DQU6 DQU5 DQU4 DQU3 DQU2 DQU1 DQU0 DQL7 DQL6 DQL5 DQL4 DQL3 DQL2 DQL1 DQL0

MMDQS0 B7 MMXDQS0 A7 MMDQS1 B8 MMXDQS1 A8 MMDQS2 B17 MMXDQS2 A17 MMDQS3 B16 MMXDQS3 A16 MMDM0 MMDM1 MMDM2 MMDM3 MMA0 MMA1 MMA2 MMA3 MMA4 MMA5 MMA6 MMA7 MMA8 MMA9 MMA10 MMA11 MMA12 MMA13 C7 D7 D17 C17 B13 D10 F10 G12 G9 C11 D9 F12 F11 E9 C13 D11 G13 A10 MMA0 MMA1 MMA2 MMA3 MMA4 MMA5 MMA6 MMA7 MMA8 MMA9 MMA10 MMA11 MMA12 MMA13

L2 K3 K1 J3 L3

CS# CAS# ODT RAS# WE#

T2 RESET# L8 ZQ R3438 240 M3 BA2 N8 BA1 M2 BA0

CK J7 CK# K7 CKE K9 NU NU NU NU NU J1 J9 L1 L9 T7

L2 K3 K1 J3 L3

CS# CAS# ODT RAS# WE#

T2 RESET# L8 ZQ R3442 240 M3 BA2 N8 BA1 M2 BA0

CK J7 CK# K7 CKE K9 NU NU NU NU NU J1 J9 L1 L9 T7

MEMORY I/F

TO DIGITAL MAIN 5 IC3101(5/8)

MMBA0 MMBA1 MMBA2 MMCK MMXCK MMXCS0 MMXCS1 MMXRAS MMXCAS MMXWE MMODT0 MMODT1 MMCKE0 MMCKE1 MMXRESET MMRODT

G14 C12 D14 A11 B11 F14 E14 G11 B12 A13 E11 C14 E10 F15 D13 N10

R3420 33 R3421 33

R3425 R3426 R3446 R3447

33 33 33 33 R3427 10K

R3428 240

I
10-11

L
PL12.0SCBD2

Digital Main 3 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

(NO CONNECTION) CN3111 GND 2 BOOTSWAP 1

CONTINUE DIGITAL 6 AL+3.3V P-ON+3.3V

R3135 OPEN R3137 10K R3134 10K

R3222 10K R3223 10K

*1 IC3101(3/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER EAS ECLK ERXW ESZ0 ESZ1 XECS0 XECS1 XECS3 NU XERE XEWE0 XEWE1 XDBG-IRQ FRC-RDY-1 XIRQ3 XIRQ4 XIRQ5 XIRQ6 XIRQ7 PCCD1 PCREADY N4 RMC0 ED0 ED1 ED2 ED3 ED4 ED5 ED6 ED7 NU NU NU NU NU NU NU NU NANDRYBY NFALE NFCLE XNFCE XNFWE XNFWP XNFRE NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU EA0 EA1 EA2 EA3 EA4 EA5 EA6 EA7 EA8 EA9 EA10 EA11 EA12 EA13 EA14 EA15 NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU K20 A25 J20 B24 E22 H20 A24 F21 G20 C23 D22 A23 B23 F20 A22 E21 A19 C20 B20 E19 G19 F19 A20 L24 N26 N24 M20 L25 Y25 W25 V24 T23 Y26 W26 W24 Y24 T21 V4 J21 H26 H22 G24 G26 H23 G25 F24 J22 F25 H21 E24 E25 G23 E26 G22 D24 P3 P5 T1 R2 R4 R3 T3 R6 M22 N22 M21 M25 N20 N25 M23 AA11 AF10 R3115 R3116 R3129 R3130 R3131 R3166 R3167 R3168 100 100 100 100 100 100 100 100 ED0 ED1 ED2 ED3 ED4 ED5 ED6 ED7

R3132 OPEN R3124 10K

CONTINUE DIGITAL 1 FRC-CTRL3 CONTINUE DIGITAL 4 XRST1 R3199 OPEN

CONTINUE DIGITAL 7 RESET

3
(NO CONNECTION) CN3104 GND 10 RESET 9 EJTCK 8 JTDI 7 JTDO 6 JTMS 5 TRSTN 4 EVTRG 3 XRST 2 AL+3.3V 1 C3962 OPEN CONTINUE DIGITAL 9 PWR-DETECT

R3203 56K 4 IC3104 OUT PST8429UR GND (RESET) 1 R3192 220 C3101 1 R3630 270 C3102 OPEN D3102 OPEN R3111 OPEN 3 CD VDD 2 C3132 0.047 C3131 1000P R3208 OPEN

E23 H25 B25 B26 R3216 OPEN C26 D26 F23 C25 F22 D23 G21 C24 E1 R3195 OPEN U2 U3 T6 V2 T5 U6 L20 M24 D2 E4 R3185 OPEN R3198 10K

C3125 0.1 IC3102 K9F2G08U0C-SCB0 (NAND FLASH MEMORY) 1 NU 2 NU BC3105 0 3 NU 4 NU 5 NU 6 NU 7 R/B 8 RE 9 CE 10 NU 11 NU R3128 10K R3123 10K 12 VCC 13 VSS 14 NU

C3126 0.1

MEMORY I/F

NU 48 NU 47 NU 46 NU 45 I/O7 44 I/O6 43 I/O5 42 I/O4 41 NU 40 NU 39 NU 38 VCC 37 VSS 36 NU 35 NU 34 NU 33 I/O3 32 I/O2 31 I/O1 30 I/O0 29 NU 28 NU 27 NU 26 NU 25 ED3 ED2 ED1 ED0 ED7 ED6 ED5 ED4

TO DIGITAL MAIN 5 IC3104(5/8)

R3171 R3172 R3173 R3174 R3175 R3176 R3177

22 22 100 100 39 100 39

AB6 XRSTSTM

AC3 XRST

C3129 OPEN AC26 EJTCK Y22 JTDI AA25 JTDO AB24 JTMS W20 TRSTN D25 BOOTSWAP R3240 1K M6 M5 L7 M4 M3 L6 M2 M7 NU NU NU NU NU NU NU NU

R3138 R3139 R3140 R3141 R3142 R3143 R3144 R3145 R3264

10K 10K 10K 10K 10K 10K 10K 10K 10K

15 NU 16 CLE 17 ALE 18 WE 19 WP 20 NU 21 NU 22 NU

R3127 10K

R3112 10K D3181 OPEN

R3113 10K

R3093 OPEN D3182 OPEN R3180 OPEN R3184 OPEN R3183 OPEN Q3181 OPEN Q3182 OPEN

R3094 OPEN

R3236 1K

23 NU 24 NU

R3227 1K

R3099 OPEN C3190 OPEN

N1 EVTRG R3136 10K CONTINUE DIGITAL 8 P-ON+12V/+21V R3164 OPEN Q3106 OPEN R3147 OPEN Q3105 OPEN R3163 OPEN CONTINUE DIGITAL 5 COMP-DET R3187 47K R3202 10K C3121 OPEN N2 N4 N6 P1 N7 NU NU NU COMP-DET NU

R3224 R3983 R3984 R3985 R3986 R3987 R3988 R3989 R3990

1K 10K 10K 10K 10K 10K 10K 10K 10K

R3189 47K

A3 SCL0 B4 SDA0 AF3 AXI

C3128 10P C3124 10P

X3101 R3169 24.576MHz OPEN R3170 0 AE3 U17 U16 AD2 AA6 N7 P2 N5 AXO NU NU NU NU NU NU NU

R3190 47K R3191 47K R3913 47K R3914 47K

U20 SDA1 U23 SCL1 AA10 SCL0 AB10 SDA0

R3269 10K

DIGITAL MAIN CBA UNIT

O
10-12

R
PL12.0SCBD3

Digital Main 4 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.
CONTINUE DIGITAL 6 P-ON+3.3V AL+3.3V CONTINUE DIGITAL 7 UART1TX UART1RX *1 IC3101(4/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER C22 D21 C2 F6 C1 H6 U25 U26 R23 R22 U24 V25 P23 R21 D1 R24 P24 P20 N23 R25 P21 P26 R20 V3 U5 W2 W1 C21 E20 B21 B22 AC6 AC4 V21 UART0TX UARTORX UARTORX UARTOTX UART1TX UART1RX USB0(-) USB0(+) USB0-OD USB0-EN USB1(-) USB1(+) USB1-OD USB1-EN NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU NU PWR-DETECT C3004 OPEN R3010 4.7K TO DIGITAL TO DIGITAL MAIN 5 MAIN 5 IC3104(5/8) IC3104(5/8) C3011 0.1 DEMODULATOR /MPEG DECODER AE6 AD6 NU AB7 IF-AGC AD7 TU-SDA AD9 TU-SCL AE10 R3004 10K R3006 100 R3007 100 C3009 0.1 DMDSCL1 AE8 DMDSDA1 AD8 NU NU NU NU NU NU NU NU NU NU NU NU NU NU AA7 AF8 AD14 AA8 AC7 AB8 AD5 AD4 AE5 AC19 AD26 AA19 AB19 AE26 C3006 OPEN R3011 47K R3025 47K D3907 MM5Z5V6B C3010 OPEN C3005 OPEN C3008 100P C3026 C3014 OPEN 0.1 C3027 OPEN R3009 4.7K C3002 OPEN C3003 OPEN L3003 3.3uH C3013 L3004 39P 3.3uH D3001 MM5Z5V6B D3002 MM5Z5V6B R3048 270 R3049 270

TU3002 OPEN
IF-AGC

TU3001 TUNER UNIT


IF-AGC

+3.3V

DIF-1

DIF-2

+3.3V

DIF-1

GND

SDA

SCL

GND

SDA

(NO CONNECTION) GND UARTORX UARTOTX P-ON+5V TO WIRELESS LAN ADAPTOR USB+5V USB0(-) USB0(+) GND (NO CONNECTION) USB0(+) USB0(-) USB0+5V GND GND GND

CN3101 4 3 2 1 C3115 OPEN CN3705 1 2 3 4 CN3701 1 2 3 4 5 6 CN3704 1 2 3 4 C3116 R3101 OPEN OPEN C3117 R3108 OPEN OPEN L3707 C3787 R3757 OPEN OPEN C3786 R3756 OPEN OPEN OPEN

R3220 OPEN R3221 OPEN

R3241 10k R3121 R3120 R3214 R3213 R3194 R3193 R3217 OPEN OPEN 100 100 100 100 47K

SCL

R3278 10k

R3981 R3982 OPEN OPEN L3706 OPEN

R3964 OPEN C3738 1

IC3703 BD2224G-TR (HIGH SIDE SWITCH) 1 VIN VOUT 5 2 GND 3 /EN R3828 10K /OC 4 C3704 0.1 C3854 220/6.3V C3855 OPEN R3755 100

(USB JACK) USB+5V USB1(-) USB1(+) GND

C3741 R3760 OPEN OPEN IC3701 BD2224G-TR (HIGH SIDE SWITCH) 1 VIN VOUT 5 2 GND 3 /EN R3761 10K /OC 4 C3727 0.1

C3740 R3759 OPEN OPEN

R3963 OPEN C3739 1 CONTINUE DIGITAL 8 P-ON-H2 CONTINUE DIGITAL 7 LCD-P-ON P-ON-H2 (NO CONNECTION) CN3103 AL+3.3V 1 P-ON-H2 2 CONTINUE DIGITAL 9 SW-EN LED1 REMOTE CONTINUE DIGITAL 9 STM-SCL STM-SDA AMP-MUTE CONTINUE DIGITAL 9 PWE DETECT

DIF-2

D3004 OPEN

C3742 220/6.3V

C3743 OPEN

R3758 100

R3118 OPEN R3109 10K

L3001 BK1608HS220-T C3007 OPEN C3023 10 C3001 10 IC3001 OPEN 1 V0 R3039 OPEN C3029 OPEN R3038 OPEN R3037 OPEN R3036 OPEN 2 FB 3 GND 4 NU VCC 8 NU 7 NU 6 EN 5 C3022 OPEN C3024 OPEN CONTINUE DIGITAL 8 P-ON+5V C3021 OPEN C3028 OPEN D3005 MM5Z5V6B

R3021 10K R3197 100 R3196 OPEN R3921 OPEN R3146 22 V23 AMP-MUTE AC23 NU W23 LED1 AB25 ARC-MUTE V20 LCD-PON AA23 NU

R3096 22K

R3162 22 R3212 100K R3158 22

PROTECT1 AA5 PROTECT3 AE1 AE2 P-ON-H2 AC25 STM-EEPROM-WP NU W22 NU U21

R3160 100 R3161 100 R3910 10K

CONTINUE DIGITAL 7 PROTECT1 PROTECT3 P-ON-H1 CONTINUE DIGITAL 8 PROTECT1 CONTINUE DIGITAL 9 LIGHT-SENS KEY-IN1

IC3103 M24C16-WMN6TP (MEMORY) 1 A0 VCC 8 R3154 OPEN 2 A1 3 A2 R3155 10K CONTINUE DIGITAL 5 VGA-SDA VGA-SCL ARC-MUTE 4 VSS WP 7 SCL 6 SDA 5

R3165 100 R3178 100 R3152 4.7K R3153 4.7K R3156 39 R3157 39 R3151 10K

R3148 0

Y20 VGA-SCL AA20 VGA-SDA AC23 NU AC5 STM-SCL AE4 STM-SDA AD25 NU Y19 NU Y23 REMOTE

LIGHT-SENS AB5 KEY-IN1 AF2 R3353 0 P-ON-H1 V22 C3127 0.1 R3354 OPEN Q3104 OPEN R3352 OPEN R3351 OPEN Q3103 OPEN R3349 OPEN R3350 OPEN

CONTINUE DIGITAL 3 XRST1

DIGITAL MAIN CBA UNIT

U
10-13

X
PL12.0SCBD4

Digital Main 5 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 8 P-ON+5V

DIGITAL MAIN CBA UNIT


JK3701 COMPONENT-Y /VIDEO-IN C3771 39P C3770 39P C3703 39P R3725 OPEN R3724 OPEN R3721 OPEN D3702 OPEN D3701 OPEN D3704 OPEN C3723 OPEN C3724 OPEN C3725 OPEN R3713 75 R3702 75 R3704 75 R3289 R3283 R3284 R3285 R3280 R3281 R3282 100 100 100 100 100 100 100 C3200 1 C3219 OPEN

*1 IC3101(5/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER AA16 NU AB16 NU Y14 NU AF13 NU Y13 NU AC14 NU AB17 AB14 AA15 AA14 Y18 AA17 Y17

4
CONTINUE DIGITAL 3 COMP-DET

COMPONENT -Pb-IN COMPONENT -Pr-IN

A/D CONVERTER

R3019 100 DIGITAL AUDIO OUT (COAXIAL) AUDIO(L)-IN JK3706 C3705 100P C3706 1 R3017 220 R3018 110 R3708 91K R3709 91K D3703 OPEN D3707 OPEN R3020 OPEN Q3001 2SC4081UBTLQ (BUFFER) C3019 33P C3721 OPEN C3722 OPEN

R3015 10K R3016 10K

C3016 1

C3196 C3197 C3198 C3193 C3194 C3195 R3840 75

1 1 1 1 1 1

SW

TO DIGITAL MAIN 2 IC3104(2/8) TO DIGITAL MAIN 3 IC3104(3/8) TO DIGITAL MAIN 7 IC3104(7/8) TO DIGITAL MAIN 4 IC3104(4/8)

R3843 75

R3841 75

R3287 100 R3286 100

OPEN OPEN OPEN OPEN OPEN OPEN

C3710 56P C3711 56P

AB9 VGA-HSYNC AA9 VGA-VSYNC AC16 NU AF7 NU

DIGITAL SIGNAL PROCESS

C3192 OPEN R3308 0

AUDIO(R)-IN

JK3713 PC-RGB-IN

C3220 C3218 C3217 C3216 C3215 C3214


R3288 39 R3303 39 R3304 39

1 2 3 4 5

6 7 8 9

11 12 13 14

R3835 OPEN

R3836 OPEN

R3848 OPEN

C3199 1 C3209 1 C3210 1

AB15 AA18 AC17 SCALER

10 15

D3711 1SS400 R3839 4.7K R3838 4.7K

C3207 1 C3208 1

OPEN OPEN 10K 10K

OPEN OPEN OPEN OPEN OPEN

AD10 R3297 110K AD13 R3298 110K AE13

SPDIF

TO DIGITAL MAIN 1 IC3104(1/8)

D3712 1SS400 CONTINUE DIGITAL 4 VGA-SDA VGA-SCL ARC-MUTE CONTINUE DIGITAL 9 AMP(L)-OUT AMP(R)-OUT CONTINUE DIGITAL 6 P-ON+3.3V

C3017 OPEN

C3018 0.01

R3307 10K

C3015 OPEN

C3020 0.01

R3013 220 R3005 220

Q3004 2SA1576UBTLQ (MUTE) R3991 47K R3001 2K

Q3002 2SC4081UBTLQ (BUFFER) R3008 220

R3012 220

CONTINUE DIGITAL 7 BACKLIGHT-SW ARC-OUT

R3003 10K

Q3003 2SA1576UBTLQ (BUFFER)

R3014 56 C3012 1

R3125 10K R3919 10K

R3002 10K

C3025 OPEN

AB13 NU AA13 NU AA12 NU AB12 NU AUDIO AE12 NU I/F AD11 NU AE11 NU AF11 NU R5 NU R7 NU U1 NU T2 NU AE9 NU AC10 AB11 V7 NU AA4 NU AB4 NU Y6 NU L26 NU K24 NU L22 NU K26 NU L21 NU K25 BACKLIGHT-SW J24 NU K22 NU J25 NU K21 NU H24 NU P25 NU T20 NU T25 NU

R3847 R3846 R3831 R3830

D3717 D3716 D3715 D3714 D3713

TO DIGITAL MAIN 7 IC3104(7/8)

TO DIGITAL MAIN 4 IC3104(4/8)

AA
10-14

AB

AC

AD
PL12.0SCBD5

Digital Main 6 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

CONTINUE DIGITAL 1 P-ON+3.3V C3167 OPEN C3159 OPEN C3171 OPEN

BC3101 0 L3106 BEAD L3117 BEAD C3173 1 C3174 0.1 C3156 0.1 C3155 0.1

*1 IC3101(6/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER T10 VDD33 T11 VDD33 R10 AVDDPLLD1-33 R11 AVDDPLLA-33 P16 AVDDPLLD2-33

DIGITAL MAIN CBA UNIT


VDD12 VDD12 VDD12 VDD12 VDD12 VDD12 VDD12 VDD12 VDD12 VDD12 VDDR VDDR VDDR VDDR VDDR VDDR VDDR M15 M16 N11 N13 N14 N15 P10 P11 T13 U12 M13 M14 N12 K11 K12 L11 L12 BC3104 0 C3136 10 C3137 OPEN C3138 0.1 C3139 0.1 C3140 0.1 C3141 0.1 BC3103 OPEN

CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V

L3119 BEAD CONTINUE DIGITAL 3 AL+3.3V P-ON+3.3V CONTINUE DIGITAL 5 P-ON+3.3V L3101 BEAD L3120 BEAD C3135 OPEN C3158 OPEN C3176 0.1

M12 DPAVDD33

BC3102 0 C3142 10 C3143 0.1 C3144 0.1 C3151 OPEN

F4 LVVDD33 C3134 0.1 P17 AVDDAPUSB33-0 C3133 0.1 R17 AVDDAPUSB33-1

L3123 BEAD CONTINUE DIGITAL 7 P-ON+3.3V AL+3.3V L3121 BEAD L3108 BEAD CONTINUE DIGITAL 9 AL+3.3V CONTINUE DIGITAL 10 P-ON+3.3V L3115 0 L3110 0 R3205 0 CONTINUE DIGITAL 2 VCC+1.5V R3204 510 C3164 10 C3163 OPEN C3170 0.1

VDDRA M11 Y11 AVDDEVE33 LVVDD12 E2 AD22 AVDDH33 C3175 1 Y10 AVDDADA33 C3162 0.1 Y12 AVDDHP33 C3114 0.1 L10 VDD25TCON C3105 0.1 M17 VDD5 C3104 0.1 VDDIOCK15 H8 C3224 1 AF5 VDD33STM C3150 1 Y7 STMADAVDD33 C3152 0.1 T22 VDDSD18-33 C3172 0.1 AD23 AVDDH18 C3161 0.1 VREFLSIF AC8 U14 VDDAVAD18 C3160 0.1 Y8 AVDDSIF18 C3113 0.1 Y9 AVDDV33 C3103 0.1 L3116 OPEN VREFH0 Y16 VREFL0 Y15 USB0RREF T26 USB1RREF T24 AE7 VCOMP NU *A FPEN R12 TESTSEL T12 GND *B VREF1V5 AD12 VREFHSIF AC9 C3182 1 C3180 1 C3181 1 C3183 1 C3185 0.01 C3187 1 C3184 1 C3186 1 R3211 6.2K R3210 6.2K VDD12STM AF4 C3153 1 VDDIO15-1 VDDIO15-2 VDDIO15-3 VDDIO15-4 F7 G8 G15 G16 C3146 1 C3147 1 C3148 0.1 C3149 0.1 VDDUSB12 N17 C3166 10 C3165 0.1 C3157 0.1 R3181 4.7 C3145 0.47

L3102 BEAD

L3107 BEAD

L3109 BEAD

L3124 BEAD

L3103 BEAD

L3105 0

L3114 BEAD

CONTINUE DIGITAL 8 P-ON+3.3V VCC+1.5V AL+3.3V AL+1.25V VCC+1.8V VCC+1.25V

L3111 0 L3112 BEAD L3113 BEAD L3104 BEAD

*A:D18~D20,E13.E18,F13,J23,K23,L23,N3,N21,P4, P6,P22,R16,T4,T16,U4,U22,AC12,AC13,AC15, AC18,AD16,AD17,AD19 *B:A1,A26,D12,D15,E3,E5,E8,E12,E16,F5,F9,G5, G7,H5,H7,K10,K13~K17,L13~L17,N16,P12~P15, R13~R15,T14,T15,T17,U10,U11,U13,U15,W7, AC11,AC21,AD3,AD20,AF1,AF26

AE

AF

AG
10-15

AH

AI

AJ
PL12.0SCBD6

Digital Main 7 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT


CONTINUE DIGITAL 4 LCD-PON P-ON-H2 *1 IC3101(7/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER JK3717 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 HDMICONNECTOR-1 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC ARC HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT CONTINUE DIGITAL 5 BACKLIGHT-SW ARC-OUT

CONTINUE DIGITAL 1 VCOM-PWM LCD-PON BACKLIGHT-ADJ OE2 PROTECT3

(NO CONNECTION) CN3602 BACKLIGHT-SW 1 BACKLIGHT-ADJ(DC) 2 P-ON-H1 3 GND 4 BACKLIGHT-ADJ(PWM) 5 AL+5V 6 GND 7 GND 8 GND 9 GND 10 P-ON+12V 11 P-ON+12V 12 P-ON+12V 13 AMP+13V 14

R3660 OPEN C3683 OPEN C3678 OPEN C3677 OPEN R3663 OPEN C3679 OPEN

R3666 OPEN R3665 OPEN R3667 OPEN C3690 OPEN

C3687 OPEN

C3686 OPEN D3616 OPEN R3668 OPEN R3659 OPEN C3689 OPEN

HDMI I/F

R3664 OPEN C3692 OPEN C3688 OPEN C3691 OPEN C3685 OPEN

C3646 R3955 C3648 C3647 C3649 C3656 C3658 C3657 C3659

TO POWER SUPPLY CBA CN631 VCOM-PWM(NU) BACKLIGHT-SW BACKLIGHT-ADJ PROTECT3 PROTECT1 P-ON-H1 P-ON-H2 RESET OE2(NU) GND AL+3.3V GND AMP+13V AMP+13V GND P-ON+21V P-ON+21V GND GND GND GND P-ON+21V P-ON+21V

CN3601 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

R3601 OPEN R3620 100 R3603 100 R3645 OPEN R3629 OPEN R3647 100 R3636 OPEN AUDIO DECODER VIDEO DECODER

AE17 AF17 AE16 AF16 AD15 AE15 AE14 AF14 AD21 AE21 AE20 AF20 AE19 AF19 AD18 AE18 AE25 AF25 AE24 AF24 AE23 AF23 AE22 AF22

C3767 0.1

R3791 10K R3960 47K R3705 10K

R3787 47K R3706 10K

R3788 47K R3786 1K

C3769 OPEN D3721 OPEN

C3768 OPEN

OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN

R3790 Q3701 2SC4081UBTLQ OPEN (SWITCHING)

C3766 OPEN JK3716 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 HDMICONNECTOR-3 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND +5V HOT PLUG DETECT

C3660 OPEN C3652 OPEN C3653 OPEN C3675 OPEN

R3956 OPEN C3651 OPEN C3650 OPEN C3676 OPEN C3655 OPEN C3632 OPEN R3628 100 Q3611 OPEN R3627 OPEN R3972 OPEN R3973 OPEN

TO DIGITAL MAIN 5 IC3101(5/8)

TO DIGITAL MAIN 5 IC3101(5/8) HDMI-CEC STMCECPUL HDMI0-SCL HDMI0-SDA HDMI1-SCL HDMI1-SDA HDMI2-SCL HDMI2-SDA

AA21 AB18 AA22 AA24 W21 Y21 AB22 AB23

R3179 100 R3992 R3993 R3994 R3995 R3996 R3997 39 39 39 39 39 39 C3759 0.1

R3784 10K R3785 47K R3707 10K

R3781 47K R3710 10K

R3780 47K R3779 1K

C3760 OPEN D3720 OPEN

C3761 OPEN

HDMI0-HPD AB21 HDMI1-HPD AD24 HDMI2-HPD AC24 HDMIO-5V AB20 HDMI1-5V AC22 HDMI2-5V AC20

R3783 Q3702 2SC4081UBTLQ OPEN (SWITCHING)

C3758 OPEN JK3715 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 HDMICONNECTOR-2 DATA2(+) TMDS DATA2 SHIELD DATA2(-) DATA1(+) TMDS DATA1 SHIELD DATA1(-) DATA0(+) TMDS DATA0 SHIELD DATA0(-) CLOCK(+) TMDS CLOCK SHIELD CLOCK(-) HDMI-CEC NU HDMI-CLOCK HDMI-DATA GND HDMI+5V HOT-PLUG-DETECT

CONTINUE DIGITAL 4 PROTECT1 PROTECT3 P-ON-H1 CONTINUE DIGITAL 8 P-ON+12V/+21V AL+5.3V CONTINUE DIGITAL 9 LCD-PON CONTINUE DIGITAL 3 RESET CONTINUE DIGITAL 9 AMP+13V CONTINUE DIGITAL 8 DC-DC-EN

R3694 OPEN C3696 OPEN R3637 OPEN

R3623 OPEN Q3612 OPEN HDMI-UART-CTRL AB26

R3863 27K D3722 1SS400

R3865 22

R3671 OPEN R3672 OPEN R3674 OPEN Q3622 OPEN Q3621 OPEN R3670 OPEN C3694 OPEN R3669 OPEN R3675 OPEN Q3620 OPEN

R3673 OPEN R3649 OPEN R3648 OPEN R3684 OPEN C3600 OPEN

R3600 OPEN

R3730 0 Q3706 OPEN R3714 10K R3720 33K R3771 OPEN R3772 OPEN R3717 1K Q3705 2SC4081UBTLQ (SWITCHING) R3715 10K R3716 33K R3777 10K C3750 R3778 0.1 47K R3773 47K R3712 10K R3711 10K R3774 47K R3775 1K C3751 OPEN D3719 OPEN C3749 OPEN C3752 OPEN

Q3704 2SC4081UBTLQ (SWITCHING)

CONTINUE DIGITAL 4 UART1TX UART1RX CONTINUE DIGITAL 6 P-ON+3.3V AL+3.3V

R3776 Q3703 2SC4081UBTLQ 100K (SWITCHING)

AK

AL

AM
10-16

AN

AO

AP
PL12.0SCBD7

Digital Main 8 Schematic Diagram [TYPE B]

CONTINUE DIGITAL 7 DC-DC-EN D3611 MM5Z15B R3695 OPEN R3682 10K Q3601 2SA1576UBTLQ (SWITCHING) R3609 4.7K Q3602 2SC4081UBTLQ (SWITCHING) C3612 0.01 IC3606 MP2303ADN (+1.5V REG.) C3667 0.01 CONTINUE DIGITAL 1 P-ON+12V/+21V P-ON+5V CONTINUE DIGITAL 4 P-ON+5V CONTINUE DIGITAL 5 P-ON+5V C3662 OPEN C3673 4.7 C3674 4.7 C3664 OPEN 1 BS 2 VIN 3 SW 4 GND L3603 22uH R3685 OPEN C3968 OPEN C3668 470/4V C3669 10 SS 8 EN 7 COMP 6 FB 5 R3679 9.1K R3634 560 C3671 10 R3633 11K R3635 4.7K C3666 0.015 D3908 OPEN R3657 OPEN R3658 OPEN R3908 OPEN C3693 OPEN C3661 0.047 R3631 10K C3665 OPEN R3687 OPEN C3967 OPEN C3609 4.7 C3616 4.7 C3610 OPEN R3607 0 R3683 100K C3702 OPEN R3904 OPEN C3604 OPEN

DIGITAL MAIN CBA UNIT

CONTINUE DIGITAL 4 P-ON-H2 R3610 4.7K C3626 1 D3614 1SS400

R3608 10K

R3611 OPEN

IC3601 MP2303ADN (+3.3V REG.) 1 BS 2 VIN 3 SW 4 GND L3604 22uH C3615 OPEN SS 8 EN 7 COMP 6 FB 5 R3677 47K R3605 100 C3614 10 R3604 15K R3606 11K C3611 0.015 C3607 0.047

D3607 OPEN C3608 10 C3613 OPEN R3643 OPEN D3613 OPEN R3655 OPEN R3656 OPEN

C3603 10

C3606 OPEN

Q3604 OPEN

BC3106 0 C3670 10 C3672 R3642 10 OPEN R3095 10K

CONTINUE DIGITAL 7 P-ON+12V/+21V AL+5.3V CONTINUE DIGITAL 9 P-ON+5V C3663 OPEN

Q3605 OPEN

C3624 OPEN

C3625 4.7

C3631 4.7

R3622 0 R3626 OPEN C3630 OPEN IC3604 MP2303ADN (+1.25V REG.) 1 BS 2 VIN 3 SW 4 GND SS 8 EN 7 COMP 6 FB 5 R3676 5.1K R3689 OPEN C3969 OPEN L3601 10uH C3640 OPEN C3641 10 R3624 560 C3643 10 C3642 OPEN C3644 OPEN R3640 OPEN R3613 10K R3625 4.7K C3638 0.015 C3620 0.01 C3601 0.015 R3686 OPEN C3966 OPEN L3605 10uH

IC3607 MP2303ADN (+5V REG.) 1 BS 2 VIN 3 SW 4 GND SS 8 EN 7 COMP 6 FB 5

C3617 0.047

R3618 10K

R3909 OPEN

CONTINUE DIGITAL 3 P-ON+12V/+21V C3605 OPEN C3645 4.7 C3654 4.7

C3639 0.01 C3629 OPEN

R3678 47K R3616 6.2K C3622 OPEN C3621 10

R3617 10K

C3618 OPEN R3614 10K C3619 4700P

C3628 10

C3623 10

D3612 OPEN

D3610 OPEN D3606 1SS400 Q3606 OPEN (SWITCHING) C3627 OPEN D3615 CRY68 R3644 OPEN R3653 OPEN R3654 OPEN IC3605 BD00IC0WEFJ (+1.8V REG.) 1 V0 VCC 8 NU 7 NU 6 EN 5 C3697 OPEN C3698 OPEN C3681 OPEN C3684 10 R3650 2.2K

CONTINUE DIGITAL 4 PROTECT1

IC3602 AP2126K-ADJTRG1 (+1.25V REG.) 1 VIN VOUT 5 C3637 2.2 C3971 R3681 OPEN OPEN D3604 MM5Z3V6B R3619 100 C3699 OPEN R3615 OPEN D3605 OPEN C3635 OPEN R3612 100K Q3608 2SA1576UBTLQ (SWITCHING) C3972 OPEN R3602 2.2K C3602 10 IC3603 AP2121AK-3.3TRE1 (+3.3V REG.) 1 VIN VOUT 5 2 GND 3 CE C3634 OPEN ADJ 4 R3692 OPEN R3691 OPEN C3974 1 C3636 R3639 OPEN OPEN 2 GND 3 CE ADJ 4 R3621 OPEN R3690 0 C3973 1 C3633 R3638 OPEN OPEN

R3661 OPEN R3662 OPEN

Q3603 OPEN

D3725 1SS400 R3688 100 C3680 220/6.3V C3682 10 R3680 OPEN

2 FB 3 GND 4 NU

C3695 R3651 OPEN 12K R3652 11K

CONTINUE DIGITAL 6 P-ON+3.3V VCC+1.5V AL+3.3V AL+1.25V VCC+1.8V VCC+1.25V

R3632 10K

R3641 10K R3646 22K Q3609 2SC4081UBTLQ (SWITCHING) C3963 0.47

AQ

AR

AS
10-17

AT

AU

AV
PL12.0SCBD8

Digital Main 9 Schematic Diagram [TYPE B]

CONTINUE DIGITAL 6 AL+3.3V CONTINUE DIGITAL 8 P-ON+5V CONTINUE DIGITAL 4 SW-EN LED1 REMOTE R3188 OPEN CN3105 1 2 3 4 5 6 7 8 9 C3111 OPEN Q3107 OPEN R3200 OPEN Q3108 OPEN R3206 OPEN R3215 OPEN

DIGITAL MAIN CBA UNIT

R3207 OPEN R3209 OPEN R3107 100

R3102 1K

TO FUNCTION CBA CN4001 SDA SCL GND KEY-IN1 REMOTE LED1 LIGHT P-ON+5V AL+3.3V

C3107 100P R3117 10

C3109 OPEN R3323 OPEN Q3102 OPEN C3108 OPEN R3106 OPEN R3103 OPEN R3104 OPEN C3106 OPEN R3149 0 C3130 OPEN R3159 OPEN R3182 10K CONTINUE DIGITAL 4 LIGHT-SENS KEY-IN1

C3110 100P

C3112 OPEN Q3101 2SC4081UBTLQ (LED DRIVE)

R3119 OPEN

C3975 R3201 OPEN 0 C3122 OPEN C3123 OPEN R3105 100 D3101 OPEN R3110 33 R3114 33 R3827 10K

3
CONTINUE DIGITAL 4 STM-SCL STM-SDA AMP-MUTE

R3150 10K

CONTINUE DIGITAL 5 AMP(L)-OUT AMP(R)-OUT C3818 10 C3817 4.7

R3998 2.7K C3964 C3808 470P 1 C3819 10 R3814 27K 30 29 28 27 26 25 24 23 22 21

CONTINUE DIGITAL 7 LCD-PON

CONTINUE DIGITAL 3 PWR-DETECT CONTINUE DIGITAL 4 PWR-DETECT

2
Q3801 2SC4081UBTLQ (SWITCHING) CONTINUE DIGITAL 7 AMP+13V R3816 10K

VREFF

PROT

AVCC

R3815 10K

ROSC

GND

GND

GND

GND

GND

NU

R3999 2.7K C3809 1 C3965 470P R3806 R3817 33K 47K

R3818 OPEN

31 GND 32 33

CBIAS 20 19 18 CONTROL LOGIC 17 GND 16 GND 15 PWM GENE. PWM GENE. VDD 14 VDD 13 12 11

C3820 10 R3813 OPEN R3822 10K R3807 OPEN C3833 R3823 0.1 100K R3820 10K

R3851 OPEN Q3803 2SA1576UBTLQ (SWITCHING) R3821 22K Q3802 2SC4081UBTLQ (SWITCHING) L3801 33uH D3801 MM5Z33B R3804 OPEN C3806 OPEN L3802 33uH C3811 0.1 R3819 22K C3825 0.1 C3810 100/25V C3822 100/25V C3812 0.1 C3824 0.1 C3803 100/25V R3824 OPEN C3834 R3826 OPEN OPEN R3825 OPEN R3864 OPEN C3807 OPEN R3832 OPEN CN3801 1 2 3 4 R3805 22K R3850 OPEN R3802 180 R3861 OPEN C3804 100/25V C3823 100/25V C3832 100/25V R3849 OPEN C3830 OPEN R3833 OPEN R3801 180 C3801 OPEN L3803 OPEN C3802 OPEN JK3801 HEADPHONE JACK

R3812 0 34 C3821 0.1 35 GND 36 GND 37 VDD C3827 100/25V C3816 0.1 38 VDD 39 40

DVDD1

GND

HB2

GND

GND

GND

GND

GND

R3808 0 R3809 0 R3810 0 R3811 OPEN

IC3801 R2A15122FP -W00R (AUDIO AMP)

1 C3814 0.1

4 C3828 10

7 R3834 0

HB1
9

10 C3813 0.1 D3802 MM5Z33B

GND

R3803 OPEN C3805 OPEN

R3800 OPEN R3799 OPEN

C3829 C3815 100/25V 0.1

C3826 C3831 100/25V OPEN

Q3804 OPEN

SP(L) GND GND SP(R)

SP3801 SPEAKER L-CH

SP3802 SPEAKER R-CH

AW

AX

AY
10-18

AZ

BA

BB
PL12.0SCBD9

Digital Main 10 Schematic Diagram [TYPE B]


1 NOTE: The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into eight and shown as IC3101 (1/8) ~ IC3101 (8/8) in this Digital Main Schematic Diagram Section.

DIGITAL MAIN CBA UNIT

4
*1 IC3101(8/8) MN2WS0172A DIGITAL SIGNAL PROCESS /MAIN MICRO CONTROLLER

R3875 22 C3980 OPEN R3871 22 C3976 OPEN R3872 22 C3977 OPEN R3873 22 C3978 OPEN R3874 22 C3979 OPEN R3733 22 MII_CRS MII-COL MII-RXCLK RMII-RXD0 RMII-RXD1 RMII-RXD2 RMII-RXD3 RMII-RXDV RMII-RXER T7 Y1 U7 AA3 W5 W4 AB2 W3 AC1 C3756 OPEN R3732 22 R3859 0 C3708 10P C3709 10P C3755 OPEN R3745 OPEN R3737 OPEN R3741 4.7K R3967 OPEN R3726 OPEN R3740 OPEN R3837 OPEN R3739 OPEN R3966 OPEN R3738 4.7K R3727 OPEN

24

23

22

21
VDD

20
GND

19

18

17

16

15
VDD

14

13

25 26 27 28 VDD10 29 PHYRSTB 30 R3723 1K MII-TXCLK RMII-TXD0 RMII-TXD1 RMII-TXD2 RMII-TXD3 RMII-TXEN MII-MDC MII-MDIO MII-MDIO-INTL HUB-RESET WAKEUP WUC AA2 Y3 V6 Y4 Y2 Y5 W6 AC2 AB3 AD1 V5 AB1 R3829 R3842 R3844 R3845 R3852 R3853 R3854 R3855 R3877 0 22 22 22 22 22 22 22 22 R3718 4.7K R3856 22 C3982 OPEN R3736 4.7K R3735 4.7K R3857 22 C3984 OPEN R3722 OPEN 31 32 RECEIVER 33 GND 34 NU 35 NU 36
VDD VDD10-OUT

NU 12 MII/RMII CONTROLLER NU 11 PMEB 10 NU 9 PARALLE TO SERIAL SERIAL TO PARALLEL NU 8 GND 7 VDD 6 5 4 NU 3 TRANSMITTER
AUDIO -OUT

R3728 0 R3767 OPEN R3729 4.7K R3766 OPEN R3765 OPEN R3764 OPEN CN3706 8 7 6 5 4 3 2 1 C3744 0.01 C3701 0.01 (ETHERNET JACK) GND NU RD(-) RCT RD(+) TD(-) TCT TD(+)

R3749 OPEN

R3748 OPEN

RSET

VDD

GND

2 1 IC3902 RTL8201FL-VB-CG (ETHERNET I/F) C3737 0.1 R3747 OPEN R3750 OPEN

XI

XO

NU

37

38

39

40

41

42

43

44

45

NU

46

47

48

C3985 C3986 C3987 C3989 C3990 C3991 C3992

OPEN OPEN OPEN OPEN OPEN OPEN OPEN

R3878 OPEN

R3879 OPEN

R3860 10K

C3993 OPEN

R3754 2.49K

C3732 0.1 R3858 22 R3876 22

R3701 OPEN R3703 0

C3731 0.1

C3730 0.1

C3736 0.1

C3733 0.1

C3999 0.1

X3701 25MHz C3735 12P

CONTINUE DIGITAL 6 P-ON+3.3V

BC3704 BK1608HS220-T C3753 OPEN

C3983 OPEN

C3981 OPEN

R3719 4.7K

R3954 4.7K

C3734 15P

BC

BD

BE
10-19

BF

BG

BH
PL12.0SCBD10

Power Supply CBA Top View


CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

4A 125V

CAUTION ! : For continued protection against risk of fire, replace only with same type 4A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

BA21N0F0102 1
D661B R655

C662

C1007

RISK OF FIREREPLACE FUSE AS MARKED


FH601 FH602

C1010

IC601

J125 GND

D660 D663 J601 GND D610

C1011

F601 4A/125V
CN601 D601 C601 D604 BC603 C605 D603

L1001

R654

BC1002

C604
D650 C651 C652

/BLACK LIVE /WHITE NEUTRAL


L601 D602

C1001

D605B

R601 SA601

C602 R613 R657 J123 GND J120 GND R607

R1003

J116 GND D1002 J117 VCC


1.ILED4 2.ILED3 3.NC 4.VLED 5.NC 6.ILED1 7.ILED2

R608

R612 R606 J602 J603 GND GND D609 Q602 R611

T601

C650

CN1001

P-ON+21V J119 J118 J115 GND

6 D402B

C654

GND

GND

J105 J126 AMP+13V J114 GND

J110 PROTECT3 J111 PROTECT3 J112 BL-Adj

D608 C655 R671 C656 D658

J106 J107 GND P-ON+21V J113 P-ON+21V D406

D607 BC601 Q601 C603

J124 GND

R670

R672

D657B

C60 6
R602

HOT
CN631 2

D1005B

Q656 D654 JS632 ALL+3.3V forR-SoC ALL+5.3V forP-SoC J109

P-ON-H2

COLD

J122

D666

J101 ALL+3.3V/ALL+5.3V D652

D401

D405

J108 RESET

D662

JS631 P-ON+21V forZ-SoC C663

J104 AMP+13V J102 GND

J103 GND

R5 01
GND J121 GND

R650 22

23.NC 22.BL-SW 21.BL-ADJ 20.P3 19.P1 18.NC 17.P-ON-H2 16.RESET 14.15.GND 13.ALL+3.3V /ALL+5.3V 12.GND 10.11.AMP+13V 9.GND 7.8.21V 3.4.5.6.GND 1.2.21V

BC602 1 23

No.4

C7A3

A3
BA21N0F01021

10-20

Power Supply CBA Bottom View


CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F601) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
Because a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing. Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.

4A 125V

CAUTION ! : For continued protection against risk of fire, replace only with same type 4A, 125V fuse. ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.

NOTE: The voltage for parts in hot circuit is measured using hot GND as a common terminal.

C662

C1007 R1004

C1008

Q654 Q652

D661

BA21N0F0102 1
D661B R655 R655A IC601

C1010

D1001

R667

C1003

D1004

F601 4A/125V
FH601 FH602

D663A

J125 GND

R663

R661

C1012 C1011

D660
C1009 Q1001 D663 R664

C1013

C659 R659 R654 R654A

C1002

J601 GND
D610 CN601

L1001

C1016 C1017 C1001

R666 R669

BC1002 C1005

C610

D610A D605B R608A

R657 R665 J123 GND

R668

R660

J116 GND
R1503 R1501 C1018

C1004

R657A C660 R658

R613

J120
R1001

Q653

R606 D605 R612A

C1006

R1005

T601

C1021

C1022

R1012

R1019

R1017 R1015 C1020

R1014

R607A

VCC

J117

C650

R613A

D102A C1019

24

R1002

R606A

13

C609

R612

D1002

GND

R607

R608

R1003

C602

R601 SA601

CN1001

C604
R502

D609A

7 R1021 IC1001

D650
J119 C652 C651

Q501

D402 R1020

R1018

D608A

D609 C608

J118 R1016

J602 GND
R610 D607A L601

R401 1

J115 12 GND R403

C501 C607

GND
GND D652A D654A

J603
D502

R1009

D402B R402

C654

R1502

R1504

R1006

C1014 R1008

J126

GND

C1015

R1011

D653

J105 AMP+13V

Q602
R651 D657

R611

J111 PROTECT3 J112 BL-Adj

D1005

R671A

R652

J106

J114 GND

R1007

D608
D602 D601 D604 C601 R604 R605 D603 R603

D406A

R670A

C655
D658

J110 PROTECT3

R671

J107 GND R675 P-ON+21V D658A R676

R672

R1010

R670

J124 GND

D405A

J113 P-ON+21V
D406

C656

D656

D607
D657B R662 C658

R673

C664

C603

R653

BC601

Q601
C60 6

R677 P-ON-H2

D1005B

D401A

R672A

J109

C665

Q650

Q656

Q655

D401

C632

D654 JS632

R680

C661

D666A

D662
JS631 P-ON+21V forZ-SoC C663

J101 ALL+3.3V/ALL+5.3V D652 R681

C631 D405

C633 J108 RESET

R682

D666

D501

C630

R678

R602

BC603 C605
R614

C638

J103 GND J102 GND

C639

J104 AMP+13V
C636

J122 GND
R5 01

R650

23.NC 22.BL-SW 21.BL-ADJ 20.P3 19.P1 18.NC 17.P-ON-H2 R650A 16.RESET 14.15.GND 13.ALL+3.3V /ALL+5.3V 12.GND 10.11.AMP+13V 9.GND 7.8.21V 3.4.5.6.GND 1.2.21V C637

C635

22

J121 GND

CN631 2 BC602

23

10-21

BA21N0F01021

Function CBA Top View

R4056 TP4055 C4058 TP4059

D4052

R4011 R4012 R4014 R4010 R4002 R4004 R4006 C4001 R4007 R4005 R4003 R4001 R4008
IC4001
b

C4006 R4013 C4002

NO.7

R4063
R4053

TP4061 C4053 TP4062 TP4060

R4061
TP4058

C4055 R4054 R4052


C4052

TP4054

R4062

C4054

R4059 R4055

A30C5

C7A3

A3

CN4001

R4058
TP4057 C4057

R4009

POWER

CH +

CH -

SOURCE

D4051

MENU

VOL +

VOL -

D4053 R4051 C4051 TP4056 C4056

R4057

Function CBA Bottom View

IC4051

R4017

RS4051

R4022 C4003 D4001

D4003 D4004
P b

BA2176G0203 2

TPP

D4002

R4021

10-22

BA2176G02032

[TYPE A]

SP3801 SPEAKER L-CH

SP3802 SPEAKER R-CH

CL3801

1 CN3101 CN4001 9 CL3101 1 CN3801

COMPONENT -Y/VIDEO-IN

FUNCTION CBA
1
AC CORD

COMPONENT -Pb-IN

COMPONENT -Pr-IN

REAR

TUNER UNIT

AUDIO(L)-IN

1 CN601

AUDIO(R)-IN

WIRING DIAGRAMS

11-1
CN3701 CN631 23 CL3701 23 1 1

DIGITAL AUDIO-OUT (COAXIAL)

DIGITAL MAIN CBA UNIT

POWER SUPPLY CBA

HDMICONNECTOR

CN1001 1 7

SIDE

PC-RGB-IN

CL1001

USB JACK

CN3011 1 CL3006

LCD PANEL ASSEMBLY


31

HEADPHONE JACK

PL12.0AWI

[TYPE B]

SP3801 SPEAKER L-CH

SP3802 SPEAKER R-CH

CL3801

COMPONENT -Y/VIDEO-IN

1 CN3105 CN4001 9 CL3101 1 CN3801

COMPONENT -Pb-IN

FUNCTION CBA
1
AC CORD

COMPONENT -Pr-IN

AUDIO(L)-IN

TUNER UNIT

REAR

AUDIO(R)-IN

1 CN601

DIGITAL AUDIO-OUT (COAXIAL)

11-2
CN3601 CN631 1 CL3701 23 23 1

ETHERNET JACK

DIGITAL MAIN CBA UNIT

POWER SUPPLY CBA

PC-RGB-IN

HDMICONNECTOR-1

CN1001 1 7

HDMICONNECTOR-2

HDMICONNECTOR-3

CL1001

SIDE

WIRELESS LAN ADAPTOR

CN3905 1 CL3006

USB JACK

LCD PANEL ASSEMBLY


31

HEADPHONE JACK

PL12.0BWI

EXPLODED VIEWS
[TYPE A]
A1

LCD1 A20 A4 CL3006 B1 CL1001 LCD Module L3 A2

A23 L3 Digital Main CBA Unit

L13 B11 S7 CL3701 L51 L13 A14 B18

Function CBA

L3 L3 L23 L3 B3 L13 L13 L14 CL3801 Power Supply CBA CL3101 L13 AC601 B9 L14 L14 L14 A3 B17

See Electrical Parts List for parts with this mark.


SP3801

L4 SP3802

L4

Stand Assembly L4 A18 S7 SSK1

L4

12-1

PL12.0-A_CEX

[TYPE B]

A1

LCD1 A20 A4 CL3006 B1 CL1001 LCD Module L3 A2

A23 L3 Digital Main CBA Unit L13

B11

S7 CL3701 L51 L13

B18 A14

Function CBA

L3 L3 L23 L3 B3 L13 L13 CL3801 Power Supply CBA CL3101 L13 AC601 B9 L14 L14 L14 L14 A3 B17

See Electrical Parts List for parts with this mark.


SP3801

L4 SP3802

L4

L14 L4

Stand Assembly L4 A18 S7 SSK1

12-2

PL12.0-B_CEX

Packing
X1 Stand Assembly Upper Side Lower Side X2 X7

X9

S7

Tape
X12 S3 X3 X4

SSK1

TYPE B X17 X18

Tape

S6

Fixlon Tape

Packing Tape
X6

Packing Tape
S4

S1

RE

E SID R A

S7

R REA

E SID

Packing Tape

Some Ref. Numbers are not in sequence.

12-3

PL12.0-A_PEX

TYPE A PARTS LIST [22PFL4507/F7 (Serial No.: ME1), 22PFL4507/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

LCD PANEL ASSEMBLY


Ref. No. LCD1 A1 A2 B1 CL1001 CL3006 L3 Description LCD PANEL ASSEMBLY Consists of the following FRONT CABINET A2176UT REAR FRAME PAINT A2170UT GASKET_274X2.5X1.6 A2170UT WIRE ASSEMBLY 7PIN FFC WX1U2A70-F01 LVDS WIRE ASSEMBLY 30PIN WX1U2A70W01 SCREW P-TIGHT 3X10 BIND HEAD+ SCREW M3X4 M3X4 BIND+ (B-NI) LCD MODULE Part No. U2A71PA 1EM029025 1EM127113 1EM437681 WX1U2A70-F01 WX1U2A70-W01 GBHP3100 SBH33040 ----------

Ref. No. A3 A4 A14 A18# A20 A23 AC601# B9 B11 B17 B18 CL3101 CL3701 CL3801 L4 L13 L14 SSK1 SP3801 SP3802 S1 S3 S4 S6 S7 X1 X2# X3 X4 X6 X7 X9 X12

Description STAND ASSEMBLY A2176UT REAR COVER A2176UT DECORATION PLATE A2176UT JACK HOLDER A2176UT RATING LABEL A2176UT LOGO LABEL A21F5UH ENERGY GUIDE LABEL A2176UT

Part No. 1ESA31545 1EM029026 1EM227065 1EM332678 ----------------------------

L51

AC CORD W/O A GND WIRE UL/CSA/1680/NO/ WAC1620LW002 BLACK STAND HOLDER A2176UT SENSOR PLATE A2176UT WALL MOUNT BRACKET A11N0UH WALL MOUNT COVER A2170UT FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/ 90MM FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/ 70MM WIRE ASSEMBLY 4PIN 4PIN/165MM&40MM SCREW P-TIGHT 3X12 BIND HEAD+ BLK SCREW S-TIGHT M3X6 BIND HEAD+ S-TIGHT SCREW M3X6 BIND HEAD+BLACK STAND SCREW KIT A21N0UT SPEAKER MAGNETIC 8OHM/3.5W S0307F19 SPEAKER MAGNETIC 8OHM/3.5W S0307F19 1EM029047 1EM332503 1EM434637 1EM332137 WX1A2170-101 WX1A21N0-109 WX1A21N0-309 GBHP3120 GBJS3060 GBHS3060 1ESA31179 DS08070XQ006 DS08070XQ006 1EM332957 1EM029345 1EM029346 1EM332797 ---------1EM437637 1EMN29340

PACKING
CARTON A2176UT STYROFOAM TOP A2176UT STYROFOAM BOTTOM A2176UT SET BAG A1777UT SERIAL NO. LABEL A01PBUH

ACCESSORIES
POLYETHYLENE BAG HDPE 180X340XT0.02 OWNERS MANUAL A2176UT

REMOTE CONTROL TRANSMITTER YKF259- URMT34JHG001 001 BATTERY R03-B500/01S QUICK START GUIDE A2176UT REGISTRATION CARD (PHILIPS) A2176UT BROCHURE (PHILIPS) A01N2UH XB0M451CZB01 1EMN29341 1EMN29339 1EMN26419

CABLE MANAGEMENT TIE(BLACK) A01F2UH 1EM431197

2012/4/3

13-1

A2176CA.fm

Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....0.25% G.....2% M.....20% D.....0.5% J......5% N.....30% F.....1% K.....10% Z.....+80/-20%
Ref. No. C1019 C1022 CN601# CN631 CN1001 Description CHIP CERAMIC CAP .(1608) B K 4.7F/6.3V CHIP CERAMIC CAP . B K 470pF/50V Part No. CHD0KK30B475 CHD1JK30B471 JCVHC02JG002 JC96J23ER009 JC96J07ER007

CONNECTORS
CONNECTOR S2P3-VH (LF)(SN) FPC/FFC CONNECTOR IMSA-9615S-23C-PPA FPC/FFC CONNECTOR IMSA-9615S-07A-PPA

DIODES
D102A D401A D402 D501 D502 D601 D602 D603 D604 D605 D607# D608# D609A# D610A D650 D653 D654# D656 DIODE SWITCHING HSC119 TRF -E DIODE SWITCHING HSC119 TRF -E ZENER DIODE SMD TFZGTR24B DIODE ZENER SMD UDZSNPTE-1733B DIODE ZENER SMD UDZSNPTE-1730B DIODE 1N5397BD DIODE 1N5397BD DIODE 1N5397BD DIODE 1N5397BD ZENER DIODE MM5Z4V3B DIODE ZENER 1ZB27BB DIODE ZENER 1ZB36BB DIODE SWITCHING HSC119 TRF -E DIODE SWITCHING HSC119 TRF -E DIODE SCHOTTKY BARRIER SB2150BD DIODE SCHOTTKY SMD SK210TD DIODE ZENER 1ZB20BB DIODE FAST RECOVERY RS1BJTB ZENER DIODE MM5Z20B IC SHUNT REGULATOR SL431A-AT DIODE ZENER SMD PZU5.6B2.115 IC SHUNT REGULATOR SL431A-AT DIODE SWITCHING HSC119 TRF -E SCHOTTKY BARRIER DIODE SMD SK110TC QD1Z00HSC119 QD1Z00HSC119 QD1B000TFZ24 QD1B0UDZNP33 QD1B0UDZNP30 NDL1001N5397 NDL1001N5397 NDL1001N5397 NDL1001N5397 ND1BMM5Z4V3B NDWZ0001ZB27 NDWZ0001ZB36 QD1Z00HSC119 QD1Z00HSC119 NDWZ00SB2150 ND1Z0SK210TD NDWZ0001ZB20 ND1Z0RS1BJTB ND1B0MM5Z20B NSZBA0TAUK01 ND1200PZU5R6 NSZBA0TAUK01 QD1Z00HSC119 ND1Z0SK110TC QPEL781FBLLF

DIGITAL MAIN CBA UNIT


Ref. No. Description DIGITAL MAIN CBA UNIT Part No. A2176MMA-002

POWER SUPPLY CBA


Ref. No. Description POWER SUPPLY CBA Consists of the following Part No. A2176MPW-001

D657 D660 D661 D662 D666A D1001 IC601# IC1001#

CAPACITORS
C501 C602# C604# C605 C606 C607 C608 C609# C610 C650 C651 C652 C654 C655 C656 C660 C663 C665 C1001 C1003 C1004 C1006 C1008 C1009 C1010 C1013 C1014 C1016 C1017 CHIP CERAMIC CAP .(1608) F Z 0.1F/50V SAFTY CAP . 2200pF/250V KX CAP METALIZED FILM 0.47F/275V/K CAP ELE 100F/200V/M/85 CERAMIC CAP . 470pF/2KV CHIP CERAMIC CAP . B K 1200pF/50V CHIP CERAMIC CAP .(1608) B K 0.047F/50V CHIP CER. BK 0.082F/50V CHIP CERAMIC CAP .(1608) B K 1000pF/50V CAP CERAMIC HV 1500pF 1KV B K CAP ELE 470F/25V/M/85 CAP ELE 470F/25V/M/85 CAP ELE 470F/25V/M/85 CAP ELE 470F/25V/M/85 CAP ELE 1F/50V/M/85 CHIP CERAMIC CAP .(1608) B K 0.1F/50V CAP ELE 100F/10V/M/85 CHIP CERAMIC CAP .(1608) B K 0.1F/50V CAP ELE 330F/25V/M/85 CHIP CERAMIC CAP .(1608) B K 1F/25V CHIP CERAMIC CAP .(1608) B K 1F/25V CHIP CERAMIC CAP . B K 470pF/50V CHD1JZ30F104 CA2E222MR101 CTA474PKR001 CEB1010S6016 CA3D471PAN04 CHD1JK30B122 CHD1JK30B473 CHD1JK30B823 CHD1JK30B102 CA3A152TE006 CED4710V8006 CED4710V8006 CED4710V8006 CED4710V8006 CEF1R00V8006 CHD1JK30B104 CEB1010V8006 CHD1JK30B104 CED3310V8006 CHD1EK30B105 CHD1EK30B105 CHD1JK30B471

ICS
IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) IC LED BACKLIGHT CONTROLLER HA7209PC NSCA0T00H003 /SOP /24PIN

COILS
L601# L1001 COIL LINE FILTER JLB20154/18MH COIL SEALED POWER INDUCTORS CWKBNP-470K LLEG0Z0XB022 LLF4700KV002

TRANSISTORS
Q501# Q601# Q602# Q650 Q652 Q653 Q656 Q1001# R401 R402 R501# R502 R601# R602 R603 R604 R605 FET 2SK3498(T6L1FUNANQ FET MOS TK5A50D(LS1FND3 QM TRANSISTOR 2SC2120-Y(TE2 F T) CHIP TRANSISTOR KTC3875S-Y-RTK/P CHIP TRANSISTOR KTC3875S-Y-RTK/P CHIP TRANSISTOR KTC3875S-Y-RTK/P TRANSISTOR 2SC2120-Y(TE2 F T) FET MOS SMD AP18T10AGH-HF QF1Z02SK3498 QEE1TK5A50DM QQSY2SC2120F NQ1YKTC3875S NQ1YKTC3875S NQ1YKTC3875S QQSY2SC2120F NF2Z18T10AGH RRXA472HH013 RRXA302HH013 RN02470ZU001 RRXA155HH013 RCX2125T1003 RWJ1R2PAK004 RRX4334HH034 RRX4334HH034 RRX4334HH034

RESISTORS
RES CHIP 1608 1/10W J 4.7k RES CHIP 1608 1/10W J 3.0k METAL OXIDE FILM RES. 2W J 47 RES CHIP 1608 1/10W J 1.5M RES. CARBON FILM J 1/2W J 1.2M RES CEMENT 3W J 1.2 RES CHIP 3216 1/4W J 330k RES CHIP 3216 1/4W J 330k RES CHIP 3216 1/4W J 330k

CHIP CERAMIC CAP .(3216) X7R K 1.0F/100V CA2A105MR080 CHIP CERAMIC CAP .(3216) X7R K 1.0F/100V CA2A105MR080 CAP ELE 47F/100V/M/85 CHIP CERAMIC CAP .(1608) B K 1000pF/50V CHIP CERAMIC CAP .(1608) B K 1F/25V CHIP CERAMIC CAP .(1608) F Z 0.1F/50V CEH4700V8006 CHD1JK30B102 CHD1EK30B105 CHD1JZ30F104 CHIP CERAMIC CAP .(3216) X7R K 1.0F/100V CA2A105MR080

2012/04/04

13-2

A2176EL.fm

Ref. No. R606 R607 R608 R611# R612 R613 R614 R650 R651# R652 R653 R654 R655 R657 R658 R659 R660 R661 R662 R663 R664 R665 R668 R669 R670 R671 R672 R673# R677 R678 R680 R681 R682 R1001 R1002 R1003# R1004 R1005 R1006 R1007 R1008 R1009 R1010 R1011 R1012 R1014 R1015 R1016 R1017 R1019 R1020 R1021 R1501 R1503 B3 BC601 BC602 BC1002 F601# FH601 FH602

Description RES CARBON FILM T 1/4W J 270 RES CARBON FILM T 1/4W J 270 RES CARBON FILM T 1/4W J 1.2k METAL OXIDE FILM RES. 2W J 0.68 RES CARBON FILM T 1/4W J 2.2k RES CARBON FILM T 1/4W J 220 RES CHIP 3216 1/4W J 330k RES CARBON FILM T 1/4W J 5.6k RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W F 12.0k RES CHIP 1608 1/10W F 10.0k RES CARBON FILM T 1/4W J 180 RES CARBON FILM T 1/4W J 180 RES CARBON FILM T 1/4W J 3.9k RES CHIP 1608 1/10W J 2.7k RES CHIP 1608 1/10W F 22.0k RES CHIP 1608 1/10W F 2.70k RES CHIP 1608 1/10W F 3.30k RES CHIP 1608 1/10W F 3.30k RES CHIP 1608 1/10W J 47k RES CHIP 1608 1/10W J 10k RES CHIP 1608 1/10W J 10k RES CHIP 1608 1/10W J 22k RES CHIP 1608 1/10W J 10k RES CARBON FILM T 1/4W J 1.0k RES CARBON FILM T 1/4W J 1.0k WIRE CP STP-S-0.50 RES CHIP 1608 1/10W J 5.6 RES CHIP 1608 1/10W J 10k RES CHIP 1608 1/10W J 100k RES CHIP 1608 1/10W J 100 RES CHIP 1608 1/10W F 10.0k RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W J 10 RES CHIP 1608 1/10W J 200 METAL OXIDE RES. 1W J 0.33 RES CHIP 1608 1/10W F 160k RES CHIP 1608 1/10W F 430k RES CHIP 1608 1/10W F 27.0k RES CHIP 1608 1/10W F 100k RES CHIP 1608 1/10W F 1.10k RES CHIP 1608 1/10W F 16.0k RES CHIP 1608 1/10W J 10k RES CHIP 1608 1/10W J 100k RES CHIP 1608 1/10W F 100 RES CHIP 1608 1/10W J 240 RES CHIP 1608 1/10W J 240 RES CHIP 1608 1/10W J 10k RES CHIP 1608 1/10W J 100k RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W 0 RES CHIP 1608 1/10W 0

Part No. RCX4271T1001 RCX4271T1001 RCX4122T1001 RN02R68ZU001 RCX4222T1001 RCX4221T1001 RRX4334HH034 RCX4562T1001 RRXA000HH014 RTW1202HH008 RTW1002HH008 RCX4181T1001 RCX4181T1001 RCX4392T1001 RRXA272HH013 RTW2202HH008 RTW2701HH008 RTW3301HH008 RTW3301HH008 RRXA473HH013 RRXA103HH013 RRXA103HH013 RRXA223HH013 RRXA103HH013 RCX4102T1001 RCX4102T1001 XZ40F0REN001 RRXA5R6HH013 RRXA103HH013 RRXA104HH013 RRXA101HH013 RTW1002HH008 RRXA000HH014 RRXA100HH013 RRXA201HH013 RN01R33ZU001 RTW1603HH008 RTW4303HH008 RTW2702HH008 RTW1003HH008 RTW1101HH008 RTW1602HH008 RRXA103HH013 RRXA104HH013 RTW1000HH008 RRXA241HH013 RRXA241HH013 RRXA103HH013 RRXA104HH013 RRXA000HH014 RRXA000HH014 RRXA000HH014 RRXA000HH014 RRXA000HH014 1EM435557 XZ40F0REN001 LLBF00STU030 XZ40F0REN001 PAGE20CW3402 XH001Z0LY001 XH001Z0LY001

Ref. No. JS632 L23 SA601# T601#

Description WIRE CP STP-S-0.50 SCREW B-TIGHT D3X8 BIND HEAD+ SURGE ABSORBER 470V+-10PER TRANS POWER BCK-25CN

Part No. XZ40F0REN001 GBJB3080 NVQZ10D471KB LTT2PCMEK038

FUNCTION CBA
Ref. No. Description FUNCTION CBA Consists of the following Part No. A2176MSW-001

CAPACITORS
C4001 C4002 C4051 C4052 C4053 C4054 C4056 CN4001 D4001 D4003 D4004 D4051 IC4001 CHIP CERAMIC CAP .(1005) B K 1F/6.3V CHIP CERAMIC CAP .(1005) B K 2200pF/50V CHIP CERAMIC CAP .(2125) B K 10F/6.3V CHIP CERAMIC CAP .(1005) B K 1000pF/50V CHIP CERAMIC CAP .(1005) F Z 0.1F/16V CHIP CERAMIC CAP .(1005) F Z 0.1F/16V CHIP CERAMIC CAP .(2125) B K 10F/6.3V CHB0KK30B105 CHB1JK30B222 CHE0KK30B106 CHB1JK30B102 CHB1CZ30F104 CHB1CZ30F104 CHE0KK30B106 JC96D09ER014 ND1BMM5Z5V6B ND1BMM5Z5V6B ND1BMM5Z5V6B QP1Z13WBC8W1 NSCB0T0TY063

CONNECTOR
FFC CONNECTOR 9P 9611S-09Y916

DIODES
ZENER DIODE MM5Z5V6B ZENER DIODE MM5Z5V6B ZENER DIODE MM5Z5V6B LED WHITE SMD SML813WBC8W1

IC
IC TOUCH SENSOR MICON CY8C20336A24LQXIT

RESISTORS
R4001 R4002 R4003 R4004 R4005 R4006 R4007 R4008 R4009 R4010 R4011 R4012 R4013 R4014 R4021 R4022 R4051 R4052 R4053 R4054 R4062 RS4051 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 CHIP RES. 1/16W J 560 RES CHIP 1005 1/16W J 18k CHIP RES.(1005) 1/16W J 8.2k CHIP RES. 1/16W J 4.7k CHIP RES.(1005) 1/16W J 2.7k CHIP RES.(1005) 1/16W J 2.2k CHIP RES.(1005) 1/16W J 100 CHIP RES.(1005) 1/16W J 2.2k CHIP RES. 1/16W J 10 CHIP RES. 1/16W J 10 CHIP RES. 1/16W J 56 RES CHIP 1005 1/16W J 6.8k CHIP RES.(1005) 1/16W J 2.2k CHIP RES.(1005) 1/16W J 1k CHIP RES.(1005) 1/16W 0 RRXG561HH004 RRXG561HH004 RRXG561HH004 RRXG561HH004 RRXG561HH004 RRXG561HH004 RRXG561HH004 RRXG183HH004 RRXG822HH004 RRXG472HH004 RRXG272HH004 RRXG222HH004 RRXG101HH004 RRXG222HH004 RRXG100HH004 RRXG100HH004 RRXG560HH004 RRXG682HH004 RRXG222HH004 RRXG102HH004 RRXG000HH005

MISCELLANEOUS
SENSOR REMOTE RECEIVER GP1USC32XP USEJRS0SH004

MISCELLANEOUS
HEAT SINK PNI A11N5UH WIRE CP STP-S-0.50 BEADS INDUCTOR FBR07HA121SB-00 WIRE CP STP-S-0.50 FUSE STC4A125V U/CT FUSE HOLDER MSF-015-RS-SN (B110) FUSE HOLDER MSF-015-RS-SN (B110)

2012/04/04

13-3

A2176EL.fm

TYPE B PARTS LIST [22PFL4907/F7 (Serial No.: ME1)]


Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available.

Different parts from the original model 22PFL4507/F7 (Serial No. : ME1)
Ref. No. A3 A14 A18# A20 A23 CL3701 S1 X2# X3 X6 X17 X18 Description REAR COVER A2776UT JACK HOLDER A27F0UH RATING LABEL A2776UT LOGO LABEL A27F5UH ENERGY GUIDE LABEL A2776UT WIRE ASSEMBLY 23PIN 23PIN/55MM CARTON A2776UT OWNERS MANUAL A2776UT REMOTE CONTROL UNIT YKF255-010 QUICK START GUIDE A2776UT VUDU SHEET A2776UT WIRELESS LAN ADAPTOR WU5502S Part No. 1EM127094 1EM332537 ---------------------------WX1A2770-101 1EM437977 1EMN29439 URMT42JHG004 1EMN29440 1EMN29521 UWLUSBACM004

2012/04/03

13-4

A2776CA.fm

Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1. Parts that are not assigned part numbers (---------) are not available. 2. Tolerance of Capacitors and Resistors are noted with the following symbols. C.....0.25% G.....2% M.....20% D.....0.5% J......5% N.....30% F.....1% K.....10% Z.....+80/-20%

Different parts from the original model 22PFL4507/F7 (Serial No. : ME1)
Ref. No. Description DIGITAL MAIN CBA UNIT POWER SUPPLY CBA C651 C652 D650 R653 R662 R670 R671 R672 R680 Not used ELECTROLYTIC CAP . 1000F/25V M DIODE SCHOTTKY SB3150BH RES CHIP 1608 1/10W F 43.0k RES CHIP 1608 1/10W J 1.5k RES CARBON FILM T 1/4W J 180 RES CARBON FILM T 1/4W J 180 RES CARBON FILM T 1/4W J 180 RES CHIP 1608 1/10W F 10.0k CE1EMZNDL102 NDWZ00SB3150 RTW4302HH008 RRXA152HH013 RCX4181T1001 RCX4181T1001 RCX4181T1001 RTW1002HH008 Part No. A2776MMA-001 A2776MPW-001

2012/04/03

13-5

A2776EL.fm

REVISION HISTORY

Chassis PL12.0
2012/03/01 2012/04/02 2012/04/06 22PFL4507/F7 (Serial No.: ME1) added 22PFL4507/F8 (Serial No.: XA1) added 22PFL4907/F7 (Serial No.: ME1) added

14-1

PL12.0REV

COMPARISON LIST OF MODEL NAMES

Chassis PL12.0
22PFL4507/F7 22PFL4507/F8 22PFL4907/F7 (ME1) (XA1) (ME1) A2176UT A217AMA A2776UT

PL12.0COM

You might also like