You are on page 1of 6

www.hilti.com Profis Anchor 2.4.

8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

1
MGM New RW
9/1/2014

Specifier's comments: Connection for Option 1 for Joint D
1 Input data
Anchor type and diameter: HIT-HY 200 + HIT-V (8.8) M30
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: h
ef,opti
= 120 mm (h
ef,limit
= 600 mm)
Material: 8.8
Evaluation Service Report: ETA 11/0493
Issued I Valid: 8/8/2012 | 12/23/2016
Proof: design method SOFA design method + fib (07/2011) - after ETAG BOND testing
Stand-off installation: without clamping (anchor); restraint level (anchor plate): 2.00; e
b
= 20 mm; t = 18 mm

Hilti Grout: , multipurpose, f
c,Grout
= 30.00 N/mm
2
Anchor plate: l
x
x l
y
x t = 450 mm x 300 mm x 18 mm; (Recommended plate thickness: not calculated)
Profile: no profile
Base material:
uncracked concrete, C25/30, f
c
= 25.00 N/mm
2
; h = 800 mm, Temp. short/long: 40/24 C
Installation: hammer drilled hole, installation condition: dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm)
no longitudinal edge reinforcement
Reinforcement to control splitting according to fib (07/2011), 16.1.5 present
Geometry [mm] & Loading [kN, kNm]
www.hilti.com Profis Anchor 2.4.8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

2
MGM New RW
9/1/2014

2 Load case/Resulting anchor forces
Load case: Design loads
Anchor reactions [kN]
Tension force: (+Tension, -Compression)
Anchor Tension force Shear force Shear force x Shear force y
1 0.000 40.633 0.000 40.633
2 0.000 40.633 0.000 40.633
3 0.000 40.633 0.000 40.633
4 0.000 40.633 0.000 40.633
5 0.000 40.633 0.000 40.633
6 0.000 40.633 0.000 40.633
max. concrete compressive strain: - []
max. concrete compressive stress:
- [N/mm
2
]
resulting tension force in (x/y)=(0/0): 0.000 [kN]
resulting compression force in (x/y)=(0/0): 0.000 [kN]

1 2 3
4 5 6
x
y
3 Tension load SOFA (fib (07/2011), section 16.2.1)
Load [kN] Capacity [kN] Utilization
bbbbN
[%] Status
Steel Strength* N/A N/A N/A N/A
Combined pullout-concrete cone failure** N/A N/A N/A N/A
Concrete Breakout Strength** N/A N/A N/A N/A
Splitting failure** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (anchors in tension)
www.hilti.com Profis Anchor 2.4.8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

3
MGM New RW
9/1/2014

4 Shear load SOFA (fib (07/2011), section 16.2.2)
Load [kN] Capacity [kN] Utilization
bbbbV
[%] Status
Steel Strength (without lever arm)* 40.633 179.200 23 OK
Steel failure (with lever arm)* 40.633 65.418 63 OK
Pryout Strength** 243.800 274.916 89 OK
Concrete edge failure in direction ** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (relevant anchors)
4.1 Steel Strength (without lever arm)



V
Rk,s
[kN]




gM,s






V
Rd,s
[kN]





V
Sd
[kN]


224.000 1.250 179.200 40.633
4.2 Steel failure (with lever arm)



l [mm]




aM



44 2.00



N
Sd
/ N
Rd,s






1 - N
Sd
/ N
Rd,s






M
0
Rk
[kNm]





M
Rk,s
= M
0
Rk,s
(1 - N
Sd
/N
Rd,s
) [kNm]


0.000 1.000 1.799 1.799



V
M
Rk,s
=
aM
* M
Rk,s
/ l [kN]




gMs,b,V






V
M
Rd,s
[kN]





V
Sd
[kN]


81.773 1.250 65.418 40.633
4.3 Pryout Strength (Concrete Breakout Strength controls)



A
c,N
[mm
2
]





A
0
c,N
[mm
2
]




yA,N






c
cr,N
[mm]





s
cr,N
[mm]





k
4



369600 129600 2.852 180 360 2.000



e
c1,V
[mm]




yec1,N






e
c2,V
[mm]




yec2,N





ys,N





yre,N



0 1.000 0 1.000 1.000 1.000



N
0
Rk,c
[kN]




gM,c,p






V
Rd,c1
[kN]





V
Sd
[kN]


72.299 1.500 274.916 243.800
5 Displacements (highest loaded anchor)
Short term loading:
N
Sk
= 0.000 [kN]
dN
= 0.000 [mm]
V
Sk
= 30.099 [kN]
dV
= 0.903 [mm]
dNV
= 0.903 [mm]
Long term loading:
N
Sk
= 0.000 [kN]
dN
= 0.000 [mm]
V
Sk
= 30.099 [kN]
dV
= 1.505 [mm]
dNV
= 1.505 [mm]
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements are
valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not included in
this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
www.hilti.com Profis Anchor 2.4.8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

4
MGM New RW
9/1/2014

6 Warnings
Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
The design method ETAG (filled holes) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by
filling the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means
The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be
followed to ensure a proper installation.
Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice, blow
twice with oil-free compressed air (min. 6 bar)).
Characteristic bond resistances depend on short- and long-term temperatures.
Please contact Hilti to check feasibility of HIT-V rod supply.
The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling
the gap with mortar of sufficient sompressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
The compliance with current standards (e.g. EC3) is the responsibility of the user
Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
Fastening meets the design criteria!
www.hilti.com Profis Anchor 2.4.8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

5
MGM New RW
9/1/2014

Coordinates Anchor [mm]
Anchor x y c
-x
c
+x
c
-y
c
+y
1 -150 100 - - - -
2 0 100 - - - -
3 150 100 - - - -
Anchor x y c
-x
c
+x
c
-y
c
+y
4 -150 -100 - - - -
5 0 -100 - - - -
6 150 -100 - - - -
7 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + HIT-V (8.8) M30
Profile: no profile; 0 x 0 x 0 mm Installation torque: 0.300 kNm
Hole diameter in the fixture: d
f
= 33 mm Hole diameter in the base material: 35 mm
Plate thickness (input): 18 mm Hole depth in the base material: 120 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 190 mm
Cleaning: Premium cleaning of the drilled hole is required

7.1 Required accessories
Drilling Cleaning Setting


Suitable Rotary Hammer


Properly sized drill bit


Compressed air with required accessories
to blow from the bottom of the hole


Proper diameter wire brush


Dispenser including cassette and mixer


Dynamic set


Torque wrench

1 2 3
4 5 6
75 150 150 75
5
0
2
0
0
5
0
x
y
225 225
1
5
0
1
5
0
www.hilti.com Profis Anchor 2.4.8
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Aurecon Indonesia
Christopher Aaron
Alamanda Tower
|
Page:
Project:
Sub-Project I Pos. No.:
Date:

6
MGM New RW
9/1/2014

8 Remarks; Your Cooperation Duties
Any and all information and data contained in the Software concern solely the use of Hilti products and are based on the principles, formulas and
security regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly
complied with by the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using
the relevant Hilti product. The results of the calculations carried out by means of the Software are based essentially on the data you put in.
Therefore, you bear the sole responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you.
Moreover, you bear sole responsibility for having the results of the calculation checked and cleared by an expert, particularly with regard to
compliance with applicable norms and permits, prior to using them for your specific facility. The Software serves only as an aid to interpret norms
and permits without any guarantee as to the absence of errors, the correctness and the relevance of the results or suitability for a specific
application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the
regular backup of programs and data and, if applicable, carry out the updates of the Software offered by Hilti on a regular basis. If you do not use
the AutoUpdate function of the Software, you must ensure that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.

You might also like