You are on page 1of 14

1.

i) Trace the different conic sections when the distance of the focus from the
directrix is 30mm and eccentricity is: i) equal to 7/9, ii) equal to 1 and iii) equal to
9/7. Name the curves.
ii) A shot is discharged from the ground level at an inclination of 50o to the ground
which is assumed to be horizontal. The shot returns to the ground at a point 80 m
distant from the point of discharge. Trace the path of the shot. Take suitable scale.

2. i) Draw the involute of a pentagon of 20 mm side.


ii) Draw the involute of a circle of diameter 40 mm. Also draw a tangent and
normal at any point on the curve.

3. Construct an Archimedean spiral for one convolution. The initial and final radius
vectors are 25 mm and 100 mm respectively. Draw a tangent and the normal to the
spiral at a point 50 mm from the pole.

4. Draw the projections of a pentagonal prism 20 mm side of base and axis 40 mm


long resting on a corner such that the two base edges passing through it make equal
inclinations with HP and its base is inclined at 60o to HP, and the axis appears to be
inclined at 30o to the VP in the top view. Insert dimensions suitably.

5. A hexagonal prism base 20 mm side and axis 40 mm long is placed with one of its
base edges on HP such that the axis is inclined at 30o to HP and 45o to VP. Draw its
projections. Insert dimensions suitably.

6. A pentagonal pyramid 20 mm side of base and axis 35 mm long rests with one of
its corners on HP such that the two base edges passing through the corner on which
it rests make equal inclination with HP. The axis is inclined at 45o to VP and 30o to
the HP. Draw the top and front views of the pyramid. Insert dimensions suitably.

7. A hexagonal pyramid, base 30 mm side and axis 60 mm long has one of its slant
edges on HP such that two of its triangular faces containing the slant edge on which
it rests are equally inclined to HP. The top view of the axis appears to be inclined at
45o to VP. Draw its projections when its base is nearer to the observer than its apex.
Insert dimensions suitably.
8. A cone of base 80 mm diameter and height 100 mm is lying with one of its
generators on HP and the axis appears to be inclined to the VP at an angle of 40o in
the top view. Draw its top and front views. Insert dimensions suitably.
9. Draw the top and front views of a right circular cylinder of base 45 mm diameter
and 60mm long when it lies on HP, such that its axis is inclined at 30o to HP and the
axis appears to be perpendicular to the VP in the top view. Insert dimensions
suitably.
10. A hexagonal headed bolt without chamfer is 30 mm in diameter and cylindrical
portion is 65 mm long. The sides of the faces of the hexagonal head are 30 mm in
length and the thickness of the hexagonal head is 25 mm. The bolt is placed with
horizontal edge of the head on ground such that it is perpendicular to VP and the axis
of the bolt is inclined at 30o to HP. Draw the top and front views of the bolt. Insert
dimensions suitably.
11. For 30 feet X 40 feet (9.144 m X 12.19 m) land area is to be constructed by
leaving 2 feet (0.609 m) space at all four sides. And in the remaining area a house is
to be constructed with 2 nos of bed rooms, kitchen and 2 nos of bath cum toilet one
attaching to bed room and other as common. Draw the plan for this residential
house.
12. For 40 feet X 40 feet (12.19 m X 12.19 m) land area is to be constructed by
leaving 2 feet (0.609 m) space at all four sides. And in the remaining area a house is
to be constructed with 3 nos of bed rooms, kitchen and 3 nos of bath cum toilet
each attaching to bed room. Draw plan for this residential house.

13. A hexagonal pyramid 25 mm edge of base and axis 65 mm lies with a triangular
face on HP and the axis parallel to VP. A section plane perpendicular to HP and
inclined at 30o to VP bisects the axis of the pyramid. Draw the sectional front view
and true shape of section. Insert dimensions suitably.

14. A cylinder 60 mm diameter and 80 mm long stands with its circular base on
HP.A section plane perpendicular to VP and inclined at 60o to HP cuts the axis at a
point 28 mm from its top end. Draw the sectional top and right views and the true
shape of section. Insert dimensions suitably.

15. A cone diameter of base 60 mm and axis 70 mm long is resting on its base on
HP. It is cut by a section plane perpendicular to VP and inclined at 45o to HP. The
vertical trace of the section plane passes through the axis at a point 40 mm above
HP. Draw the sectional top view, front view and the true shape of section. Insert
dimensions suitably.

16. A cube of 30 mm edges is cut by a section plane so that the true shape of section
is a regular hexagon. Draw the projections of the cube and find the inclination of the
section plane with HP. Also measure the length of the sides of the regular hexagon in
the true shape of section. Insert dimensions suitably.

17. Draw the isometric view of the block shown in Fig.

18. Draw the isometric view of the block shown in Fig.

19. Draw the front, top and right hand side views of a bearing block shown in Fig.

20 .Draw the front, top and right hand side views of a half journal block shown in
Fig.

21. Draw the following Isometric projections.

22) (a) Draw the front view top view and right side view of the V Block shown in figure using a
Standard drafting package.
(b) Draw the simple steel truss shown in the figure using a standard drafting package.

23) Draw the following Isometric projections.

24. Draw the following plan of the residential building with suitable wall thickness.

25. Draw the 3D model of the given object and obtain the 2-D multi-views

M.P.NACHIMUTHU M.JAGANATHAN ENGINEERING COLLEGE


An ISO 9001:2008 Certified Institution
CHENNIMALAI, ERODE 638 112.

DEPARTMENT OF MECHANICAL ENGINEERING


MODEL PRACTICAL EXAM

ALLOCATION OF MARKS
Description
Allotted
Drawing
60
Dimensioning
20
List of commands used
10
Viva-voce
10
Total
100

Awarded

M.P.NACHIMUTHU M.JAGANATHAN ENGINEERING COLLEGE


An ISO 9001:2008 Certified Institution
CHENNIMALAI, ERODE 638 112.

DEPARTMENT OF MECHANICAL ENGINEERING


MODEL PRACTICAL EXAM

S.No

ROLL NO

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

NAME

Abhijith Anil
Anand Raj.R
Anbalagan.C
Aravindh.M
Arun.L
Arun Raj.S
Arun Ram.K
Ashish Varghese
Balachandhar.C
Balakannan.M
Balamurugan.M
Balasubramaniyam.R
Baskar.M
Gokul.S
Harikrishnan.B
Jayaprakash.B
Jebaz Arul Raj.J
Jithin.P
Jose B Shaju
Kandha Guru.K
Karthick.M
Karthik.G
Karthikeyan.S
Krishnamoorthy.N
Kumar.R

QUESTION
NO

SIGNATURE

M.P.NACHIMUTHU M.JAGANATHAN ENGINEERING COLLEGE


An ISO 9001:2008 Certified Institution
CHENNIMALAI, ERODE 638 112.

DEPARTMENT OF MECHANICAL ENGINEERING


MODEL PRACTICAL EXAM

S.No

ROLL NO

26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

NAME

Manickaraj.R
Manikandan.K
Manimaran.R
Manoj Kumar.A
NishadAli .M.K.
Parthasarathi.M
Prabhu.V
Pranessh.M.V.
Ragul.M
Raguman.M
Rajeesh.R
Rajesh.G
Rathna Kumar.I
Sabari.R
Sabarish.K
Sangeetha.E
Santhoshkumar.S
Saravanan.S
Sathish.D
Sathish.S
Seenuvasan.P
Silambarasan.M
Tinuvenkat.V
Vinothkumar.M
Vivek.V

QUESTION
NO

SIGNATURE

You might also like