Professional Documents
Culture Documents
Guide
dutilisation
Users
Guide
Learn how to use
your Fujitsu
LIFEBOOK LH531
notebook
WARNING
HANDLING THE CORD ON THIS PRODUCT WILL EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER HANDLING.
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Address:
Telephone:
(408) 746-6000
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device may not cause harmful interference, (2) This device must accept any interference received,
including interference that may cause undesired operation.
When using your notebook equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury
to persons, including the following:
Do not use this product near water for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with
local codes for possible special disposal instructions.
SAVE THESE INSTRUCTIONS
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH THE SAME TYPE AND
RATING FUSE.
To order a new battery for your Fujitsu mobile computer, go to the Fujitsu shopping site at www.shopfujitsu.com in the US or
www fujitsu.ca/products/notebooks in Canada.
** RBRC is an independent third party to which Fujitsu provides funding for battery recycling; RBRC is in no way affiliated with Fujitsu.
5-
Contents
Preface
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Conventions Used in the Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Fujitsu Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 1
11
14
16
17
19
20
21
21
21
21
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Controlling the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 2
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Opening the Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Adjusting Display Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Using the Windows Mobility Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Closing the Display Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Power/Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Sleep Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Hibernation (Save-to-Disk) Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Restarting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Powering Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
ENERGY STAR Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapter 3
User-Installable Features
Lithium ion Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Recharging the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Optical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Media Player Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Loading Media on Your Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Removing Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Emergency Optical Drive Tray Release . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using the Media Player Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Using Media Player on Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Internal LAN (RJ-45) Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Headphone/Line-Out Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Microphone/Line-In Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Universal Serial Bus Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
External Video Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Chapter 4
Chapter 5
Chapter 6
System Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Chipset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Mass Storage Device Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Popular Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Included Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Learning About Your Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Glossary/Regulatory
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Preface
About This Guide
The LIFEBOOK LH531 notebook from Fujitsu America provides desktop performance with the new 2nd
generation Intel Core Processor. Your notebook has a built-in 14 WXGA high-definition color
display. This system brings the computing power of a desktop personal computer to a portable
environment.
Your computer comes with Microsoft Windows 7 Home Premium operating system pre-installed.
This manual explains how to operate your LIFEBOOK notebooks hardware and built-in system software.
Conventions Used in the Guide
Keyboard and on-screen keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
Pages with additional information about a specific topic are cross-referenced within the text.
For example: (See Installation Procedure on page 43.)
On screen menu items appear in bold. Example: Click Fujitsu Menu, and select your choice.
THE INFORMATION ICON HIGHLIGHTS INFORMATION THAT WILL ENHANCE YOUR UNDERSTANDING OF
THE SUBJECT MATERIAL.
THE CAUTION ICON HIGHLIGHTS INFORMATION THAT IS IMPORTANT TO THE SAFE OPERATION OF YOUR
COMPUTER, OR TO THE INTEGRITY OF YOUR FILES. PLEASE READ ALL CAUTION INFORMATION
CAREFULLY.
THE WARNING ICON HIGHLIGHTS INFORMATION THAT CAN BE HAZARDOUS TO EITHER YOU, YOUR
LIFEBOOK NOTEBOOK, OR YOUR FILES. PLEASE READ ALL WARNING INFORMATION CAREFULLY.
You can contact Fujitsu Service and Support in the following ways:
Toll free: 1-800-8Fujitsu (1-800-838-5487)
Website: http://www.computers.us.fujitsu.com/support
Before you place the call, you should have the following information ready so that the customer support
representative can provide you with the fastest possible solution:
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Type of device connected, if any
You can go directly to the online store by visiting the website at: www.shopfujitsu.com.
YOU MUST HAVE AN ACTIVE INTERNET CONNECTION TO USE THE ONLINE URL LINKS.
Limited Warranty
Your LIFEBOOK notebook is backed by a Fujitsu International Limited Warranty. Check the service kit
that came with your notebook for the Limited Warranty period and terms and conditions.
Chapter 1
10
Web Camera
Display Panel
Stereo Speaker
Status Indicator Panel
Power/Suspend/
Resume Button
Stereo Speaker
Headphone Jack
Microphone Jack
MS/SD Card Slot
Wireless
Device Switch
Touchpad
Pointing Device
Top Components
The following is a brief description of your LIFEBOOK notebooks top components.
Web Camera
The 1.3 megapixel web camera allows you to take pictures of yourself to send over the internet. For
information on using the microphone and web cam, see the documentation associated with the CyberLink
YouCam application.
11 - Locating the Controls and Connectors
Display Panel
The display panel is a color LCD panel with back lighting for the display of text and graphics.
Status Indicator Panels
The Status Indicator Panels display symbols that correspond with a specific component of your
LIFEBOOK notebook. See Status Indicator Panel on page 19.
Power/Suspend/Resume Button
The Power/Suspend/Resume button allows you to suspend notebook activity without powering off,
resume your LIFEBOOK notebook from suspend mode, power off your notebook, and power on your
notebook when it has been shut down from Windows. See Power/Suspend/Resume Button on page 41.
Stereo Speakers
A full-size keyboard with dedicated Windows keys. See Keyboard on page 22.
Touchpad Pointing Device
The Touchpad pointing device is a mouse-like cursor control with a right button, a left button, and a cursor
control pad. See Touchpad Pointing Device on page 25.
Wireless Device On/Off Switch
The wireless device on/off switch is used to turn the optional wireless devices such as WLAN and
Bluetooth on and off. Switching the device off when not in use will help to extend battery life.See
Activating the WLAN Device on page 128.
Memory Stick/Secure Digital (MS/SD) Card Slot
The Memory Stick/Secure Digital (MS/SD) card slot allows you to install a media card for data storage.
This media allows you to transfer data from a variety of different digital devices. See Secure Digital
Cards on page 57.
Microphone/Line-In Jack
The microphone/line-in jack allows you to connect an external stereo microphone. See
Microphone/Line-In Jack on page 64.
Headphone/Line-Out Jack
The headphone/line-out jack allows you to connect headphones or external speakers. See
Headphone/Line-Out Jack on page 63.
Digital Microphone
The digital microphone is used in conjunction with the web camera. For information on using the
microphone and web cam, see the documentation associated with the CyberLink YouCam application.
DC Power Jack
Air Vents
HDMI Port
The DC power jack allows you to plug in the AC adapter to power your LIFEBOOK notebook and charge
the internal Lithium ion battery.
Air Vents
The air vents allow air to circulate through the system to cool down the components.
TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE PERFORMANCE, BE SURE TO KEEP ALL
AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC CLEANING,
DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.
DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN
TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
The external video port allows you to connect an external monitor or LCD projector. See External Video
Port on page 66.
14 - Locating the Controls and Connectors
HDMI Port
The HDMI port is used to connect compatible digital devices with your computer (such as a highdefinition television or AV receiver).
USB 2.0 Ports
The USB 2.0 ports allow you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480
Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12 Mbps. See
Universal Serial Bus Ports on page 64. Note that of the two USB 2.0 ports on the left side of the system,
the one towards the right has Anytime USB Charge capability, which allows you to charge a USB device
whether or not the system is powered on.
Optical Drive
Release Button
Optical Drive
The optical drive bay contains a Dual-Layer Multi-Format DVD Writer or a Blu-ray drive. See Optical
Drive on page 50.
Optical Drive Release Button
The USB 2.0 port allows you to connect Universal Serial Bus devices. USB 2.0 transfers data at up to 480
Mbps and is backward-compatible with USB 1.1 devices, which transfer data at up to 12 Mbps. See
Universal Serial Bus Ports on page 64.
LAN (RJ-45) Jack
The internal LAN (RJ-45) jack is used for an internal wired 10/100/1000 Gigabit Ethernet LAN
connection. See Internal LAN (RJ-45) Jack on page 63.
Anti-theft Lock Slot
The anti-theft lock slot allows you to attach an optional physical lock down device.
16 - Locating the Controls and Connectors
Air Vents
(multiple locations)
Memory
Upgrade
Compartment
Bottom Components
The following is a brief description of your LIFEBOOK notebooks bottom panel components.
Memory Upgrade Compartment
Your notebook comes with high speed Double Data Rate 3 Synchronous Dynamic RAM (DDR3
SDRAM). The memory upgrade compartment allows you to expand the system memory capacity of your
notebook, thus improving overall performance. See Memory Upgrade Module on page 59. Under
normal circumstances, it should not be necessary to open this compartment.
17 - Locating the Controls and Connectors
The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery
when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion
battery. See Lithium ion Battery on page 45.
Air Vents
The air vents allow air to circulate through the system to cool down the components.
TO PROTECT YOUR NOTEBOOK FROM DAMAGE AND TO OPTIMIZE SYSTEM PERFORMANCE, BE SURE TO
KEEP ALL AIR VENTS UNOBSTRUCTED, CLEAN, AND CLEAR OF DEBRIS. THIS MAY REQUIRE PERIODIC
CLEANING, DEPENDING UPON THE ENVIRONMENT IN WHICH THE SYSTEM IS USED.
DO NOT OPERATE THE NOTEBOOK IN AREAS WHERE THE AIR VENTS CAN BE OBSTRUCTED, SUCH AS IN
TIGHT ENCLOSURES OR ON SOFT SURFACES LIKE A BED OR CUSHION.
NumLk
Power Status
CapsLk
ScrLk
Hard Drive/Optical
Drive Access
Battery Level
Blue, blinking: AC adapter and battery are available and the system is in sleep mode.
Off: AC adapter is not plugged in.
Battery Level Indicator
The Battery Level indicator displays the charge level of the battery pack, as follows.
With AC Adapter connected:
Blue, solid: AC adapter is connected and battery is charged.
Orange, solid: AC adapter is connected and battery is charging.
Without AC Adapter connected:
Orange, blinking: Blinks when the battery charge level is 12% or less.
Purple, blinking: There is a problem with the battery.
Off: There is no AC Adapter connected and/or the battery charge level is between 13% and 100%
If the battery pack is installed while the power is turned off, the battery level indicator will display
the charge level for five seconds after it blinks orange.
If the AC adapter is not connected or the battery pack is not fully charged when the computer is
switched to standby mode, the indicator will blink. The LED blinks at the rate of one second on/six
seconds off.
NumLk Indicator
The NumLk indicator glows when the integral keyboard is set in ten-key numeric keypad mode.
CapsLock Indicator
The CapsLock indicator glows when your keyboard is set to type in all capital letters.
ScrLk Indicator
The ScrLk indicator states that your scroll lock is active.
Keyboard
Function Keys
Start Key
Fn Key
Numeric Keypad
(surrounded by thick black line)
Application Key
Cursor Keys
Figure 7. Keyboard
Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to
the right, left, up, or down within windows, applications and documents.
Function keys: The keys labeled [F1] through [F12], are used in conjunction with the [Fn] key to
produce special actions that vary depending on what program is running.
Windows keys: These keys work with your Windows operating system and function the same as
the onscreen Start menu button, or the right button on your pointing device.
Numeric Keypad
The right-hand section of the keyboard serves as a numeric keypad. To activate the keypad functions, press
the [NumLk] button. Using the keypad keys, you can enter numerals 0 through 9, perform addition ( + ),
subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated
as numeric function key keys. When [NumLk] is not active, you can use the numeric keypad to navigate
(Del, Ins, left, right, up, down).
Windows Keys
Your LIFEBOOK notebook has two Windows keys, consisting of a Start key and an Application key. The
Start key displays the Start menu. This button functions the same as your onscreen Start menu button. The
Application key functions the same as your right mouse button and displays shortcut menus for the
selected item. (Please refer to your Windows documentation for additional information regarding the
Windows keys.)
Cursor Keys
The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down,
left and right in applications. In programs such as Windows Explorer, it moves the focus (selects the
next item up, down, left, or right).
Function Keys
Your LIFEBOOK notebook has 12 function keys, F1 through F12. The functions assigned to these keys
differ for each application. You should refer to your software documentation to find out how these keys
are used.
23 - Keyboard
The [Fn] key provides extended functions for the notebook and is always used in conjunction with
another key.
[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.
[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the Touchpad on and off. Note that the
[Fn+F4] combination only works if Manual Setting is selected in the BIOS. (See BIOS Setup
Utility on page 38)
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.
[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LIFEBOOK
notebook.
[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LIFEBOOK
notebook.
[Fn+F10]: Pressing the [Fn] + [F10] keys allows you to change your selection of where to send your
display video. Each time you press the key combination, you will step to the next choice, as follows:
If you have an external CRT connected, the order is internal -> external CRT -> simultaneous
display > internal display.
[Fn+F11]: Pressing [F11] while holding [Fn] will enable and disable ECO mode. ECO mode is
designed to minimize notebook power consumption by reducing the LCD brightness, shutting
down the optical drive and ExpressCard functionality and enabling the hard disk drives auto power
off mode.
24 - Keyboard
Left Button
Right button
Cursor Control
The Touchpad pointing device comes built into your Fujitsu LIFEBOOK notebook. It is used to control
the movement of the pointer to select items on your display panel. The Touchpad is composed of a cursor
control, a left button and a right button. The cursor control works the same way a mouse does, and moves
the cursor around the display. It only requires light pressure with the tip of your finger. The left and right
buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending
on the application that is being used.
AN EXTERNAL MOUSE CAN BE CONNECTED TO THE USB PORTS ON YOUR LIFEBOOK NOTEBOOK AND
USED SIMULTANEOUSLY WITH THE TOUCHPAD. HOWEVER, IF YOU BOOT THE SYSTEM WITH AN
EXTERNAL MOUSE CONNECTED THE TOUCHPAD WILL BE DISABLED OR ENABLED DEPENDING ON THE
SPECIFICATIONS IN YOUR BIOS SETTINGS. See BIOS Setup Utility on page 38.
Clicking
Clicking means pushing and releasing a button. To
left-click, move the cursor to the item you wish to
select, press the left button once, and then immediately
release it. To right-click, move the mouse cursor to the
item you wish to select, press the right button once,
and then immediately release it. You also have the
option to perform the clicking operation by tapping
lightly on the Touchpad once.
Figure 9. Clicking with button
Double-Clicking
Double-clicking means pushing and releasing the left
button twice in rapid succession. This procedure does
not function with the right button. To double-click,
move the cursor to the item you wish to select, press the
left button twice, and immediately release it. You can
also perform the double-click operation by tapping
lightly on the Touchpad twice.
Figure 11. Double-clicking with button
Dragging
Dragging means pressing and holding the left button,
while moving the cursor. To drag, move the cursor to
the item you wish to move. Press and hold the left
button while moving the item to its new location and
then release it. Dragging can also be done using the
Touchpad. First, tap the Touchpad twice over the item
you wish to move making sure to leave your finger on
the pad after the final tap. Next, move the object to its
new location by moving your finger across the
Touchpad, and then release your finger.
To enable or disable the gesturing functions, go to Start > Control Panel > Hardware and Sound.
Double-click Mouse, and the Mouse Properties window will appear.
Select the Gestures tab and click the checkbox next to the gesture function you want to use or disable.
Double-click Mouse, and the Mouse Properties window will appear. Select any of the ten tabs to modify the
settings of your touchpad.
Volume Control
Your Fujitsu LIFEBOOK notebook has multiple volume controls which interact with each other.
ANY SOFTWARE THAT CONTAINS AUDIO FILES WILL ALSO CONTAIN A VOLUME CONTROL OF ITS OWN. IF
YOU INSTALL AN EXTERNAL AUDIO DEVICE THAT HAS AN INDEPENDENT VOLUME CONTROL, THE
HARDWARE VOLUME CONTROL AND THE SOFTWARE VOLUME CONTROL WILL INTERACT WITH EACH
OTHER. IT SHOULD BE NOTED THAT IF YOU SET YOUR SOFTWARE VOLUME TO
31 - Volume Control
Chapter 2
AC Adapter
AC Adapter
DC In
AC Cable
32
Power Sources
Your Fujitsu LIFEBOOK notebook has three possible power sources: a primary Lithium ion battery, an
AC adapter or an optional Auto/Airline adapter.
Connecting the Power Adapters
The AC adapter or optional Auto/Airline adapter provides power for operating your notebook and
charging the batteries.
Connecting the AC Adapter
1 Plug the DC output cable into the DC power jack of your LIFEBOOK notebook.
2 Plug the AC adapter into an AC electrical outlet.
Connecting the Optional Auto/Airline Adapter
1 Plug the DC output cable into the DC power jack on your notebook.
2 Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or Access,
OR,
Plug the Auto/Airline adapter into the DC power jack on an airplane seat.
THE LITHIUM ION BATTERY IS NOT CHARGED UPON PURCHASE. INITIALLY, YOU WILL NEED TO CONNECT
EITHER THE AC ADAPTER OR THE AUTO/AIRLINE ADAPTER TO USE YOUR NOTEBOOK.
33 - Power Sources
Display Panel
Your Fujitsu LIFEBOOK notebook contains a display panel that is backlit for easier viewing in bright
environments and maintains top resolution through the use of active-matrix technology.
Opening the Display Panel
To open the display, hold the base of the system with one hand, and lift the display backwards with the
other hand, being careful not to touch the screen, until it is at a comfortable viewing angle.
34 - Display Panel
WHEN USING AC POWER YOUR BRIGHTNESS SETTING IS SET TO ITS HIGHEST LEVEL BY DEFAULT. WHEN USING
BATTERY POWER YOUR BRIGHTNESS SETTING IS SET TO APPROXIMATELY MID-LEVEL BY DEFAULT.
THE HIGHER THE BRIGHTNESS LEVEL, THE MORE POWER THE NOTEBOOK WILL CONSUME AND THE FASTER
YOUR BATTERIES WILL DISCHARGE. FOR MAXIMUM BATTERY LIFE, MAKE SURE THAT THE BRIGHTNESS IS SET
AS LOW AS POSSIBLE.
The Power/Suspend/Resume button is used to turn on your LIFEBOOK notebook from its off state. Once
you have connected your AC adapter or charged the internal Lithium ion battery, you can power on your
LIFEBOOK notebook.
WHEN YOU TURN ON YOUR LIFEBOOK NOTEBOOK, BE SURE YOU HAVE A POWER SOURCE. THIS
MEANS THAT A BATTERY IS INSTALLED AND CHARGED, OR THAT THE AC OR AUTO/AIRLINE ADAPTER IS
CONNECTED AND HAS POWER.
To turn on your LIFEBOOK notebook from its off state, press the Power/Suspend/Resume button, located
above the keyboard to the right. When you are done working you can either leave your notebook in
Suspend mode (see Sleep Mode on page 41), or you can turn it off (see Powering Off on page 43).
DO NOT CARRY YOUR LIFEBOOK NOTEBOOK AROUND WITH THE POWER ON OR SUBJECT IT TO
SHOCKS OR VIBRATION, AS YOU RISK DAMAGING YOUR NOTEBOOK.
When you power on your LIFEBOOK, it will perform a Power On Self Test (POST) to check the internal
parts and configuration for correct functionality. If a fault is found, your LIFEBOOK notebook will emit
an audio warning and/or an error message will be displayed. See Power On Self Test Messages on
page 79. Depending on the nature of the problem, you may be able to continue by starting the operating
system or by entering the BIOS setup utility and revising the settings.
After satisfactory completion of the POST, your notebook will load your operating system.
NEVER TURN OFF YOUR LIFEBOOK NOTEBOOK DURING THE POWER ON SELF TEST (POST) OR IT
WILL CAUSE AN ERROR MESSAGE TO BE DISPLAYED WHEN YOU TURN YOUR LIFEBOOK NOTEBOOK ON
THE NEXT TIME. See Power On Self Test Messages on page 79.
Boot Sequence
The procedure for starting-up your notebook is termed the Bootup sequence and involves your notebooks
BIOS. When your LIFEBOOK notebook is first turned on, the main system memory is empty, and it needs
to find instructions to start up your notebook. This information is in the BIOS program. Each time you
power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until
your operating system is found. During booting, your notebook is performing a standard boot sequence
including a Power On Self Test (POST). When the boot sequence is completed without a failure and
without a request for the BIOS Setup Utility, the system displays the operating systems opening screen.
The boot sequence is executed when:
You turn on the power to your LIFEBOOK notebook.
You restart your notebook from the Windows Shut Down dialog box.
The software initiates a system restart. Example: When you install a new application.
Hard Disk Drive Passwords
To provide additional security for your data, you can assign passwords to your hard disk drive(s). This
feature is managed in the system BIOS Setup Utility. See BIOS Setup Utility below for information about
accessing the utility.
REMEMBER YOUR PASSWORDS. IF YOU SET AND FORGET YOUR USER AND MASTER HARD DISK
FUJITSU AMERICA WILL NOT BE ABLE TO RESET IT. YOU MAY LOSE DATA AND HAVE TO
REPLACE YOUR SYSTEM BOARD OR HARD DISK DRIVE.
PASSWORDS,
Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter
the current settings.
To enter the BIOS Setup Utility, press the [F2] key once the Fujitsu logo appears on the screen. This will open
the main menu of the BIOS Setup Utility with the current settings displayed.
The Boot Menu can also be invoked by pressing the [F12] key when the Fujitsu logo appears on the screen.
BIOS Guide
A guide to your notebooks BIOS is available online. Please visit our service and support website at
http://www.computers.us.fujitsu.com/support, then select Users Guides under Online Support. Select
your Product, Series, and Model, then click [Go]. Under the Manuals tab, select the BIOS Guide.
Booting the System
We strongly recommend that you not attach any external devices and do not put a DVD/CD in your drive
until you have gone through the initial power on sequence.
When you turn on your notebook for the first time, it will display a Fujitsu logo on the screen. If you do
nothing the system will load the operating system, and then the Windows Welcome will begin.
38 - Starting Your LIFEBOOK Notebook
IF YOU REJECT THE TERMS OF THE LICENSE AGREEMENT YOU WILL BE ASKED TO REVIEW THE LICENSE
AGREEMENT FOR INFORMATION ON RETURNING WINDOWS OR TO SHUT DOWN YOUR NOTEBOOK.
YOU CANNOT USE YOUR NOTEBOOK UNTIL YOU HAVE ACCEPTED THE LICENSE AGREEMENT. IF YOU STOP THE
PROCESS YOUR NOTEBOOK WILL RETURN TO THE BEGINNING OF THE WINDOWS WELCOME PROCESS, EVEN IF
YOU SHUT YOUR NOTEBOOK DOWN AND START IT UP AGAIN.
Several additional windows will appear, prompting you to enter a name and description for your computer,
an Administrator password, and a domain name. Read the instructions on the screens carefully and fill in
the information as directed. Once you have finished with the setup, it is very important that you install
Click Me!, as detailed below.
ClickMe!
BEFORE INSTALLING THE CLICK ME! UTILITY, BE SURE THE WIRELESS LAN DEVICE IS ENABLED BY
TURNING ON THE WIRELESS DEVICE SWITCH ON THE FRONT EDGE OF THE SYSTEM.
The first time you boot up your system, you will see an icon called Click Me! in the Start menu. It is very
important that you run the Click Me! utility the first time you boot up in order to ensure that the
necessary applications, utilities. and drivers are installed. When you click the Click Me! icon, your
system will automatically create the related icons in the system tray in the bottom right of the screen.
These icons provide links to utilities that you will frequently access.
When you install the Click Me! utility, several applications and utilities are installed; this takes time.
While Click Me! is installing, the system may go into Suspend mode (as indicated by a blinking
power light). If this should occur, slide the Power/Suspend/Resume button momentarily to wake the
system up. Alternately, while Click Me! is installing, slide your finger across the touchpad every few
minutes to keep the system awake.
THERE MAY BE SOME THIRD-PARTY APPLICATIONS THAT DO NOT GET INSTALLED USING THE CLICK ME!
UTILITY. FOR MORE INFORMATION, REFER TO YOUR GETTING STARTED GUIDE.
You can register your notebook by going to our website at: us.fujitsu.com/computers. You will need to
be set up with an Internet Service Provider (ISP) to register online.
Power Management
Your LIFEBOOK notebook has many options and features for conserving battery power. Some of these
features are automatic and need no user intervention. However, others depend on the parameters you set
to best suit your operating conditions, such as those for the display brightness. Internal power management
for your notebook may be controlled from settings made in your operating system, pre-bundled power
management application, or from settings made in BIOS setup utility.
Besides the options available for conserving battery power, there are also some things that you can do to
prevent your battery from running down as quickly. For example, you can create an appropriate power
saving profile, put your notebook into Sleep mode when it is not performing an operation, and you can
limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off
between performance and power savings.
Power/Suspend/Resume Button
When your notebook is active, the Power/Suspend/Resume button can be used to manually put the
notebook into Sleep mode. Push the Power/Suspend/Resume button when the notebook is active, but not
actively accessing anything, and immediately release the button. Note that if you press the button
continuously for four seconds or longer, your notebook will turn off and active data may be lost.
If your notebook is suspended, pushing the Power/Suspend/Resume button returns your notebook to
active operation. You can tell whether the system is Suspended by looking at the Power indicator. If the
indicator is visible and not flashing, your notebook is fully operational. If the indicator is visible and
flashing, your notebook is in Sleep mode. If the indicator is not visible, the power is off or your notebook
is in Hibernation mode. (See Hibernation Feature)
Sleep Mode
Sleep mode in Windows saves the contents of your system memory during periods of inactivity by
maintaining power to critical parts. This mode turns off the CPU, display, hard drive, and all other internal
components except those necessary to maintain system memory and for restarting.
Your notebook will go into Sleep mode due to one of the following actions or conditions:
41 - Power Management
IF RUNNING YOUR NOTEBOOK ON BATTERY POWER, BE AWARE THAT THE BATTERY CONTINUES TO DISCHARGE
WHILE YOUR NOTEBOOK IS IN SLEEP MODE, THOUGH NOT AS FAST AS WHEN FULLY OPERATIONAL.
DISABLING THE POWER/SUSPEND/RESUME BUTTON PREVENTS IT FROM BEING USED TO PUT THE NOTEBOOK INTO
SLEEP OR HIBERNATION (SAVE-TO-DISK) MODE. THE BUTTON RESUME FUNCTION CANT BE DISABLED.
IF YOUR NOTEBOOK IS ACTIVELY ACCESSING INFORMATION WHEN YOU ENTER THE SLEEP OR HIBERNATION MODE,
CHANGES TO OPEN FILES ARE NOT LOST. THE FILES ARE LEFT OPEN AND MEMORY IS KEPT ACTIVE DURING SLEEP
MODE OR THE MEMORY IS TRANSFERRED TO THE INTERNAL HARD DRIVE DURING HIBERNATION MODE.
THE MAIN ADVANTAGE OF USING HIBERNATION (SAVE-TO-DISK) IS THAT POWER IS NOT REQUIRED TO MAINTAIN
YOUR DATA. THIS IS PARTICULARLY IMPORTANT IF YOU WILL BE LEAVING YOUR NOTEBOOK IN A SUSPENDED STATE
FOR A PROLONGED PERIOD OF TIME. THE DRAWBACK OF USING HIBERNATION MODE IS THAT IT LENGTHENS THE
POWER DOWN AND POWER UP SEQUENCES AND RESETS PERIPHERAL DEVICES.
The default settings are enabled. To disable or enable the Hibernation feature, follow these steps:
1
2
From the Start menu, select Control Panel > Power Options.
Select Choose what the power button does or Choose what closing the lid does, then make your selection
(Do Nothing, Sleep, Hibernate, or Shut Down).
42 - Power Management
Click the [Start] button, then move the mouse over the small arrow at the bottom right of the right-hand pane.
Select Restart from the list.
TURNING OFF YOUR LIFEBOOK NOTEBOOK WITHOUT EXITING WINDOWS OR TURNING ON YOUR
NOTEBOOK WITHIN 10 SECONDS OF THE NOTEBOOK BEING SHUT OFF MAY CAUSE AN ERROR WHEN
YOU START THE NEXT TIME.
Powering Off
Before turning off the power, check that the hard drive/optical drive access indicator is off. If you turn off
the power while accessing a disk there is a risk of data loss. To ensure that your notebook shuts down
without error, use the Windows shutdown procedure.
BE SURE TO CLOSE ALL FILES AND EXIT ALL APPLICATIONS PRIOR TO TURNING OFF THE POWER. IF
FILES ARE OPEN WHEN YOU TURN THE POWER OFF, YOU WILL LOSE ANY CHANGES THAT HAVE NOT
BEEN SAVED, AND MAY CAUSE DISK ERRORS.
Using the correct procedure to shut down from Windows allows your notebook to complete its operations
and turn off power in the proper sequence to avoid errors. The proper sequence is:
Click the [Start] button, and then move the mouse over the small arrow at the bottom right of the righthand pane. Click the [Shut Down] button.
43 - Power Management
Chapter 3
User-Installable Features
Lithium ion Battery
Your LIFEBOOK notebook has a Lithium ion battery that provides power for operating your notebook
when no external power source is available. The battery is durable and long lasting, but should not be
exposed to extreme temperatures, high voltages, chemicals or other hazards.
The Lithium ion battery operating time may become shorter if it is used under the following conditions:
When used at temperatures that exceed a low of 5C or a high of 35C. Extreme temperatures not
only reduce charging efficiency, but can also cause battery deterioration. The Charging icon on the
Status Indicator panel will flash when you try to charge a battery that is outside its operating
temperature range. See Status Indicator Panel on page 19.
When using a high current device such as a Multi-Format DVD Writer, CD-ROM drive, optical
drive, or the hard drive, using the AC adapter will conserve your battery life.
DO NOT LEAVE A FAULTY BATTERY IN YOUR NOTEBOOK. IT MAY DAMAGE YOUR AC ADAPTER, OPTIONAL
AUTO/AIRLINE ADAPTER, ANOTHER BATTERY OR YOUR NOTEBOOK ITSELF. IT MAY ALSO PREVENT
OPERATION OF YOUR NOTEBOOK BY DRAINING ALL AVAILABLE CURRENT INTO THE BAD BATTERY.
45
ACTUAL BATTERY LIFE WILL VARY BASED ON SCREEN BRIGHTNESS, APPLICATIONS, FEATURES, POWER
MANAGEMENT SETTINGS, BATTERY CONDITION AND OTHER CUSTOMER PREFERENCES.
BLU-RAY
MULTI-FORMAT DVD WRITER, OR HARD DRIVE USAGE MAY ALSO HAVE A SIGNIFICANT IMPACT
ON BATTERY LIFE. THE BATTERY CHARGING CAPACITY IS REDUCED AS THE BATTERY AGES. IF YOUR
BATTERY IS RUNNING LOW QUICKLY, YOU SHOULD REPLACE IT WITH A NEW ONE.
DRIVE,
UNDER FEDERAL, STATE, OR LOCAL LAW IT MAY BE ILLEGAL TO DISPOSE OF BATTERIES BY PUTTING
THEM IN THE TRASH.
PROPERLY. CHECK WITH YOUR LOCAL GOVERNMENT AUTHORITY FOR DETAILS REGARDING RECYCLING
OR DISPOSING OF OLD BATTERIES. IF YOU CANNOT FIND THIS INFORMATION ELSEWHERE, CONTACT
YOUR SUPPORT REPRESENTATIVE AT
1-800-8FUJITSU (1-800-838-5487)
There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery
completely before recharging. The charge times will be significantly longer if your notebook is in use
while the battery is charging. If you want to charge the battery more quickly, put your notebook into
Standby mode, or turn it off while the adapter is charging the battery. (See Power Management on page
41 for more information on Standby mode and shutdown procedure)
When the battery is running low, a low battery notification message will appear. If you do not respond to
the low battery message, the batteries will continue to discharge until they are too low to operate. When
this happens, your notebook will go into Standby mode. There is no guarantee that your data will be saved
once the notebook reaches this point.
ONCE THE LOW BATTERY NOTIFICATION MESSAGE APPEARS, YOU NEED TO SAVE ALL YOUR ACTIVE DATA AND PUT
LIFEBOOK NOTEBOOK INTO STANDBY MODE UNTIL YOU CAN PROVIDE A NEW POWER SOURCE. YOU
SHOULD PROVIDE A CHARGED BATTERY, AN AC POWER ADAPTER, OR AUTO/AIRLINE ADAPTER AS SOON AS
POSSIBLE.
YOUR
WHEN YOU ARE IN STANDBY MODE THERE MUST ALWAYS BE AT LEAST ONE POWER SOURCE ACTIVE. IF YOU
LIFEBOOK NOTEBOOK IS IN STANDBY MODE, ANY DATA THAT HAS
NOT BEEN SAVED TO THE HARD DRIVE WILL BE LOST.
REMOVE ALL POWER SOURCES WHILE YOUR
Once your notebook goes into Dead Battery Suspend mode you will be unable to resume operation until
you provide a source of power either from an adapter, or a charged battery. Once you have provided power,
you will need to press the Power/Suspend/Resume button to resume operation.
In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is
not provided promptly, the Power indicator will stop flashing and go out, resulting in loss of the data that
was not stored. Once you provide power, you can continue to use your notebook while an adapter is
charging the battery.
Shorted Batteries
The Status Indicator panel uses an LED below the battery outline of the Battery Level indicator to display
the operating level available in that battery. If this display shows a Shorted Battery, it means the battery is
damaged and must be replaced so it does not damage other parts of your LIFEBOOK notebook.
47 - Lithium ion Battery
5
6
Insert a new battery into the bay, and press it down so that the latches click into place.
Hot-swapping Batteries
1
2
Optical Drive
Your system may contain one of the following optical drives:
Blu-ray Combo Drive: This drive allows you to access movies, software, and audio DVD/CDs as well
as to read the following media formats: BD-ROM (Single and Dual Layer), BD-R (Single and Dual
Layer), BD-RE (Single and Dual Layer), DVD-ROM (Single and Dual Layer), DVD+R (Single and Dual
Layer), DVD-R (Single and Dual Layer), DVD+RW (Single Layer) DVD-RW (Single Layer), DVDRAM (Ver.2), CD-ROM, CD-R and CD-RW discs.
This drive allows you to write to the following media formats: DVD-RAM (Ver2), DVD+R (Single and
Dual Layer), DVD+RW, DVD-R (Single and Dual Layer), DVD-RW, CD-R, and CD-RW discs. It also
has the same functions as an ordinary CD/DVD/BD-ROM drive.
Dual-Layer Multi-Format DVD Writer: This drive allows you to access movies, software, and audio
DVD/CDs as well as to read and write to CD-R, CD-RW, DVD-R, DVD+R, DVD-RW, DVD+RW, and
DVD RAM discs. The dual-layer architecture allows you to record up to 8.5 GB of data on DVD+R discs.
50 - Optical Drive
DO NOT OPERATE YOUR OPTICAL DRIVE UNLESS YOUR LIFEBOOK NOTEBOOK IS SITTING ON A FLAT SURFACE.
USING A DRIVE WHEN THE SYSTEM IS NOT LEVEL MAY DAMAGE THE DRIVE OR PREVENT PROPER OPERATION.
PROLONGED USE OF THE OPTICAL DRIVE, SUCH AS WATCHING A DVD MOVIE, WILL SUBSTANTIALLY REDUCE
YOUR BATTERY LIFE IF NO EXTERNAL POWER SOURCE IS ATTACHED.
Push and release the eject button on the front of the optical drive to open the holder tray. The tray will come out
of the LIFEBOOK notebook a short distance.
Gently pull the tray out until a media disc can easily be placed in the tray.
YOU SHOULD PERIODICALLY CHECK THE FUJITSU WEBSITE AT US.FUJITSU.COM/COMPUTERS FOR THE
MOST CURRENT DRIVERS.
ALL LIFEBOOK DVD PLAYERS ARE SET TO PLAY DVD TITLES WITH REGION CODE NUMBER 1 WHICH
IS SPECIFIED FOR THE NORTH AMERICAN MARKET. THE REGION NUMBER IS A REGIONAL RESTRICTION
CODE DEFINED BY THE
CODES ARE RECORDED ON VIDEO DVD TITLES FOR PUBLICATION IN DIFFERENT AREAS OF THE WORLD.
IF THE REGIONAL CODE OF THE DVD PLAYER DOES NOT MATCH THE REGIONAL CODES ON THE TITLES,
THEN PLAYBACK IS IMPOSSIBLE.
THE REGION CODE ON THE DVD PLAYER CAN BE CHANGED USING THE PROPERTIES MENU OF THE
DVD SOFTWARE. NOTE: YOU CAN ONLY CHANGE THE REGION CODE UP TO FOUR TIMES. AFTER THE
4TH CHANGE, THE LAST CODE ENTERED BECOMES PERMANENT, AND CANNOT BE CHANGED.
Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised
circle in the center of the tray.
51 - Optical Drive
Gently push the holder tray back in until you hear a click
IF YOU HAVE DISABLED THE AUTO INSERT NOTIFICATION FUNCTION, YOU WILL HAVE TO START THE
DRIVE EITHER BY USING MY COMPUTER OR FROM WITHIN WINDOWS EXPLORER, SINCE YOUR
NOTEBOOK WILL NOT AUTOMATICALLY RECOGNIZE THAT MEDIA HAS BEEN LOADED.
52 - Optical Drive
b.
a.
d.
c.
Removing Media
1
Push and release the eject button on the front of the optical drive. This will stop the drive and the holder tray will
come out of the LIFEBOOK notebook a short distance.
2
3
4
Gently pull the tray out until the disc can easily be removed from the tray.
Carefully remove the media disc from the holder tray.
Gently push the holder tray back in until you hear a click.
Emergency Optical
Drive Tray Release
If for some reason the eject button fails, you
can open the media tray with a paper clip or
similar tool inserted into the eject hole in
the right side of the front of the tray.
Straighten one side of a paper clip and push
it gently into the hole. The tray will pop out.
Figure 25. Emergency Tray Release
Starting a Movie
1
2
Insert the disc into the optical drive of the notebook. If the CD AutoRun feature activates, skip Step 2.
Click OK to close the About DVD Player Performance dialog box and the movie will begin.
The first time you insert a movie into the media tray, you will be prompted to select what you want the system
to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will
receive the same prompt whenever you insert a disc.
54 - Optical Drive
With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to
view. You can do this by using the media player control panel and the mouse.
1
2
The media player software allows you to watch the movie much like a VCR player. You can pause, rewind,
fast-forward and stop the movie at any point.
1
2
To fast-forward the movie, click the button to forward to a specific portion of the movie, or the button to jump
to the ending credits.
To rewind the movie, click the button to rewind to a specific portion of the movie, or the button to return to
the opening screen.
Click the located in the upper right corner of the title bar. This will open a media player dialog box.
Click Yes to stop and exit the movie, or No to close the media player dialog box and return to the movie.
1-877-372-3473.
Power down your notebook and replace the discharged battery with an additional fully-charged battery. If you
do not have an additional battery, you may attach AC power as soon as you see the low battery warning.
Resume operation by pressing the Suspend button again. This is not required if you attached AC power without
entering standby mode.
Restart your media player, locate and skip to the chapter of the movie you were last watching, then continue
watching your DVD movie.
SOME SHORTER DVD MOVIES MAY NOT REQUIRE YOU TO SWAP BATTERIES OR ATTACH AC POWER TO
HOWEVER, IT IS BEST TO BE PREPARED SINCE ACTUAL BATTERY LIFE WHILE
OPERATING THE OPTICAL DRIVE CANNOT BE GUARANTEED.
COMPLETE THEM.
56 - Optical Drive
SD Card
Memory Stick
See your specific card manual for instructions on the installation of your card. Some cards may require that your
notebook is off while installing them.
2
3
4
Make sure there is no card currently in the slot. If there is, see Removing a Memory Stick/SD Card.
Insert your card into the slot with the product label facing up.
Push the card firmly into the slot until it is seated in the connector.
Push the card in until it unlatches. It will then eject from the slot for removal.
THE MEMORY UPGRADE MODULE CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
TO MINIMIZE RISK TO THE MODULE, OBSERVE THE FOLLOWING PRECAUTIONS:
TERMINALS OR COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE
COMPONENTS.
BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING MEMORY MODULES.
EVEN IF THE SYSTEM IS IN HIBERNATE OR STANDBY STATES, DATA COULD BE LOST OR THE
MEMORY COULD BE DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.
Turn off power to your notebook, remove any power adapter (AC or auto/airline). Remove the battery.
Remove the new memory upgrade module from the static guarded sleeve.
Turn the notebook bottom side up, and remove the screw from the memory upgrade module compartment
(Figure 28). Remove the cover.
Align the memory upgrade module with the component side up. Align the connector edge of the memory
upgrade module with the connector slot in the compartment. Be sure the alignment keys line up with those in
the slot.(Figure 29)
Memory Cover
Insert the memory upgrade module at a 45 angle. Press the connector edge of the module firmly down and
into the connector until it lodges under the retaining clip. Youll hear a click when it is properly in place.
Alignment Keys
Retaining Clip
Retaining Clips
Retaining Clip
Figure 29. Installing memory module
Check the memory capacity by clicking [Start] -> Control Panel -> System and Maintenance ->
System. The amount of memory is displayed next to Memory - RAM:
There may be a variation between the actual memory size and what is displayed. This is possible if your
system is configured with an integrated Intel Graphics Media Accelerator which dynamically allocates
system memory to accelerate graphics performance.
IF THE TOTAL MEMORY DISPLAYED IS INCORRECT, CHECK THAT YOUR MEMORY UPGRADE MODULE IS
PROPERLY INSTALLED. (IF THE MODULE IS PROPERLY INSTALLED AND THE CAPACITY IS STILL NOT
CORRECTLY RECOGNIZED, SEE TROUBLESHOOTING ON PAGE 67.
Device Ports
Your Fujitsu LIFEBOOK notebook comes equipped with multiple ports to which you can connect external
devices including: disk drives, keyboards, printers, etc.
Internal LAN (RJ-45) Jack
The internal LAN (RJ-45) jack is used for a 10/100 Ethernet LAN connection. You may need to configure
your notebook to work with your particular network. (Please refer to your network administrator for
information on your network configuration.) To connect the LAN cable follow these steps:
1
Headphone/Line-Out Jack
The headphone/line-out jack allows you to connect headphones or powered external speakers to your
notebook. Your headphones or speakers must be equipped with a 1/8 (3.5 mm) stereo mini-plug. In order
to connect headphones or speakers follow these easy steps:
1
2
Align the connector with the port opening on the front of the system.
Push the connector into the port until it is seated.
IF YOU PLUG HEADPHONES INTO THE HEADPHONE JACK, BUILT-IN STEREO SPEAKERS WILL BE
DISABLED.
63 - Device Ports
Microphone/Line-In Jack
The microphone/line-in jack allows you to connect an external mono microphone. Your microphone must
be equipped with a 1/8(3.5 mm) stereo mini-plug in order to fit into the microphone jack of your
notebook. In order to connect a microphone follow these easy steps:
1
2
USB Ports
Figure 32. Connecting a USB Device
DUE TO THE ONGOING CHANGES IN USB TECHNOLOGY AND STANDARDS, NOT ALL USB DEVICES
AND/OR DRIVERS ARE GUARANTEED TO WORK.
64 - Device Ports
65 - Device Ports
PRESSING THE [FN] + [F10] KEYS ALLOWS YOU TO CHANGE YOUR SELECTION OF WHERE TO SEND
YOUR DISPLAY VIDEO. EACH TIME YOU PRESS THE KEY COMBINATION, YOU WILL STEP TO THE NEXT
CHOICE. IF YOU ONLY HAVE AN EXTERNAL CRT CONNECTED, THE ORDER IS INTERNAL -> EXTERNAL
CRT -> SIMULTANEOUS DISPLAY > INTERNAL DISPLAY.
66 - Device Ports
Chapter 4
Make sure that any devices connected to the external connectors are plugged in properly. You can also
disconnect such devices, thus eliminating them as possible causes of failure.
5
6
7
Turn on your notebook. Make sure it has been off at least 10 seconds before you turn it back on.
Make sure the AC adapter is plugged into your notebook and to an active AC power source.
Make sure that any cards installed are seated properly. You can also remove the card from the slot, thus
eliminating it as a possible cause of failure.
IF YOU KEEP NOTES ABOUT WHAT YOU HAVE TRIED, YOUR SUPPORT REPRESENTATIVE MAY BE
ABLE TO HELP YOU MORE QUICKLY BY GIVING ADDITIONAL SUGGESTIONS OVER THE PHONE.
If you have tried the solutions suggested in the Troubleshooting Table without success, contact your support
representative:
68 - Troubleshooting
Specific Problems
Using the Troubleshooting Table
When you have problems with your LIFEBOOK notebook, try to find the symptoms under the Problem
column of the troubleshooting table for the feature giving you difficulty. You will find a description of
common causes for that symptom under the column Possible Cause and what, if anything, you can do to
correct the condition under Possible Solutions. All possible causes or solutions may not apply to your
notebook.
Troubleshooting Table
Problem
Page
Problem
Page
69 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Manually adjusting the volume should dynamically adjust the volume of the operating (see above). If that doesnt work, adjust the
sound volume control settings in your software or application.
Headphones are
plugged in.
The Audio Driver may be installed or reinstalled by using the Drivers and Applications CD that came with your LIFEBOOK. Refer to
your application and operating system documentation for help.
Click on the Volume icon in the tool tray on the bottom right of the
screen. If Mute is checked, click on it to uncheck it. You can also
use the [Fn+F3] key combination to toggle the volume on and off.
Push on the front of the optical drive tray until it latches. If that
doesnt work, pull out the modular drive latch to remove the device
from the bay, then re-insert the drive until it latched; this ensures
that the drive is properly seated.
DVD/CD-RW/CD-ROM
is dirty or defective.
Audio Problems
There is no sound coming
from the built-in speakers.
70 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive
designations are automatically adjusted.
Check your device and operating system documentation and activate the proper driver.
71 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Check your device and operating system documentation and activate the proper driver.
Remove and re-install the device. See Device Ports on page 63.
Memory Problems
Your System Properties
screen does not show the
correct amount of installed
memory.
72 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Use the Status Indicator panel to verify the presence and condition of the battery. See Status Indicator Panel on page 19. If a
battery is indicating a short, remove that battery and operate from
another power source or replace that battery.
Power Failures
You turn on your LIFEBOOK notebook and nothing seems to happen.
73 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Make sure the adapter is plugged in and the outlet has power.
Install a power adapter and then push the Power/Suspend/Resume button. See Power Sources on page 33.
No battery is installed.
Verify the condition of the battery using the Status Indicator panel
and replace or remove any shorted battery. See Status Indicator
Panel on page 19.
The brightness is
turned all the way up.
74 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Suspend/Resume
button is disabled.
Set the operating source by pressing the [ESC] key while the
Fujitsu logo is on screen or use the [F2] key and enter the setup
utility and adjust the source settings from the Boot menu. See
BIOS Setup Utility on page 38.
Make sure you have the right password. Enter the setup utility and
verify the Security settings and modify them as accordingly. See
BIOS Setup Utility on page 38.
75 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Make sure you select Save Changes And Exit when exiting the
BIOS setup utility.
Pressing [F10] while holding down the [Fn] key allows you to
change your selection of where to send your display video. Each
time you press the keys you will step to the next choice. The
choices, in order are: built-in display only, external monitor only,
both built-in display and external monitor.
Move the display and the brightness control until you have adequate visibility. Pressing either the [F6] or [F7] keys while holding
down the [Fn] key also allows you to change the brightness level
of the display.
Power management
timeouts may be set for
short intervals and you
didnt see the display
come on and go off.
Video Problems
The built-in display is blank
when you turn on your
LIFEBOOK notebook.
76 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Power management
timeouts may be set for
short intervals and you
didnt notice the display
come on and go off.
Check the status indicator panel to verify that the Security icon is
blinking. If it is blinking, enter your password.
Display compression gives a clearer but smaller display for applications that do not support the systems native pixel resolution.
You can fill the screen but have less resolution by changing display compression settings. These settings can be changed in the
Intel GMA control panel.
Power Management
default is set on low to
conserve power.
Press [Fn] + [F7] to increase brightness or double-click on the battery gauge and adjust Power Control under battery settings.
77 - Troubleshooting
Problem
Possible Cause
Possible Solutions
Check your device and operating system documentation and activate the proper driver.
See your monitor documentation and the External Monitor Support portions of the Specifications section. See Specifications on
page 98.
To activate the wireless LAN devices, press the [Fn] and [F5] keys
at the same time. When active, the wireless LAN indicator in the
status indicator panel will glow. To turn the devices off, repeat the
same step.
Application software
often has its own set of
error message displays.
See your application manual and help displays screens for more
information. Not all messages are errors some may simply be status.
Connectivity Problems
You are attempting to connect to the Internet, but you
do not appear to have
power to the WLAN.
Miscellaneous Problems
Error message is displayed
on the screen during the
operation of an application.
78 - Troubleshooting
Problem with NVRAM access. In the unlikely case that you see this message you may have a display
problem. You can continue operating but should contact your support representative for more information.
*Keyboard controller error
The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but
may be able to use an external keyboard until then. Contact your support representative.
*Keyboard not detected
Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to
use an external keyboard until then. Contact your support representative.
*Operating system not found
Operating system cannot be located on either drive A: or drive C: Enter the setup utility and see if both
the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you
have changed your installation greatly, the operating system should be on drive C:. If the setup utility is
correctly set, your hard drive may be corrupted.
*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press [F1] key to Continue or [F2] key to Enter Setup.
*Real time clock error - Check date and time settings
Real-time clock fails BIOS test. May require board repair. Contact your support representative.
*Fan error, system shutdown in 30s. Contact Fujitsu tech support
Fan error occurred during previous boot. Please contact your sales representative.
79 - Troubleshooting
IN ORDER TO INSTALL APPLICATIONS AND DRIVERS, MAKE COPIES OF FACTORY AND SYSTEM IMAGES, AND BURN
DRIVERS AND APPLICATION RESTORE DISCS, APPLICATION MEDIA, AND BOOTABLE DISCS YOU MUST HAVE AN
INTERNAL OR EXTERNALLY CONNECTED WRITABLE DVD DRIVE.
IT IS EXTREMELY IMPORTANT THAT YOU COPY YOUR FACTORY IMAGE TO REMOVABLE MEDIA (E.G., DVD DISCS).
FAILURE TO DO SO COULD RESULT IN AN INABILITY TO RESTORE THE MAGE AT A FUTURE DATE.
WE RECOMMEND THAT YOU USE DVD-R OR DVD+R DISCS FOR YOUR BACKUP, BUT SUPPORTED MEDIA* FOR
IMAGE BACKUPS INCLUDE:
FOR FACTORY IMAGE, DAR, APPLICATION DATA, AND BOOTABLE DISC: DVD-R/+R.
FOR USER-CREATED BACKUP IMAGE: DVD-R/+R, DVD-RW/+RW, DVD-DL.
* DEPENDING UPON YOUR OPTICAL DRIVE AND MEDIA FORMAT USED, SOME MEDIA TYPES MAY BE INCOMPATIBLE
FOR CREATING IMAGE BACKUPS.
DUE TO CERTAIN LICENSING REQUIREMENTS, SOME THIRD-PARTY APPLICATIONS WILL NEED TO BE INSTALLED
SEPARATELY USING THE APPLICATION MEDIA BUNDLED WITH YOUR SYSTEM.
After you launch the ClickMe! utility when you first start up your system, you should make a copy of the
Factory Image to DVD discs. You will need several blank discs (DVD-R or DVD+R discs are
recommended) in order to create the copy. After creating the copy, be sure to label the discs and keep them
in a safe place to ensure they do not get damaged.
Creating Backup Images of Factory Image, DAR, and Discs
SOME CONFIGURATIONS OF CERTAIN LIFEBOOK MODELS DO NOT HAVE APPLICATIONS LOADED ON THE HARD
DRIVE; RATHER, THEY ARE LOADED ON THE DAR DISC. PLEASE TAKE THAT INTO ACCOUNT WHEN READING THE
FOLLOWING PROCEDURES.
Using the [Manage/Change] button, you can create backup images of the Factory Image, DAR,
Application Disc, or Bootable Disc.
1
2
3
4
The message Recovery Disc #1. will be created. Enter your comments and number of media on the DVD.
Click [YES] to burn the Factory Image.
IN THE FOLLOWING STEP, DO NOT USE THE SYSTEM UNTIL THE COPY IS COMPLETE.
While the copy is being made, a Writing to the media screen displays a progress bar. When the copy is
complete, a dialog will appear informing you of the successful completion of the backup.
Repeat the process for the remaining three images on disc (Bootable Disc, Drivers and Applications Restore
Disc, and Application Disc). The number of images available may vary depending on your system model; some
models do not have the applications loaded on the hard drive.
ALL USER-CREATED DATA WILL BE DELETED FROM YOUR SYSTEM WHEN THE FACTORY IMAGE IS RESTORED.
In order to recover your Factory Image, perform the steps outlined in Running Recovery and Utility from
hard disk on page 3.
Backing Up a System Image
User-Configured System Backups: On your desktop, there is a [MyRecovery] icon that
allows you to make backups of your current system image either to another location on your
My Recovery
hard drive or on removable media. A system image is the configuration of your C: drive at a
particular point of time. You may want to make system image backups occasionally in order to have points
to which you can return without having to go all the way back to the Factory Image.
By default, system images are saved in the D: drive in the MyRecovery folder. You can also elect to save
the image to an external hard drive.
1
2
3
After rebooting, the Creating of the backup image window appears, in which you can either click [Create the
image on D drive] or [Select the drive] if you want to save to an external hard disk drive.
6
7
An image appears showing you graphically how the image will be stored. Click the [Next] button.
Click [Execute] to start the backup.
5
6
Select an image title from the list, then click the action button you would like to perform.
Note that if you copy an image to an external hard drive, both the original and the copy will appear in the [Backup
Images] window with identical names, dates, and file sizes, but with the different drive letter to distinguish them.
Before you select [Make DVD], be sure you have a recordable DVD drive connected and blank DVDs available.
Recovery and Utility Tools are preinstalled in a hidden partition by the factory, or they can be accessed by
using the bootable disc. Please note that you can delete Recovery and Utility tools from your hard disk
drive if you modify the partitions. In this case you will not be able to use the hidden partition for booting
to Recovery and Utility Tools, but you will still be able to boot from the disc.
Determining whether Recovery and Utility is pre-loaded
1
Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key.
From the Boot Menu that appears, check whether the <Recovery and Utility> option is present. If it is not
present, it means that the utility must be used from the disc. Proceed to Running Recovery and Utility from the
Bootable Disc if <Recovery and Utility> is unavailable.
Turn on or reboot your system. When the Fujitsu logo appears, press [F12] key.
Cursor down to <Recovery and Utility> and press the [Enter] key.
While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.
When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].
When the Operating System dialog appears, select Use recovery tools..., then click [Next].
If necessary, enter your password, then click [OK].
When System Recovery Options window appears, click on Recovery and Utility.
The Recovery and Utility screen appears on the screen with three tabs: Diagnostics, Recovery and Utility.
Please note that Diagnostics tab is not supported on certain LIFEBOOK/Stylistic models when running
Recovery and Utility from the hard disk. In order to restore the operating system, please use the middle icon
Restoring the Factory Image (only C:\drive) under the Recovery tab.
THE BOOTABLE DISC CAN ONLY BE USED WITH THE SYSTEM WITH WHICH IT WAS PURCHASED.
1
2
3
4
5
6
Power on your system. When the Fujitsu logo appears on the screen. press the [F12] key.
Select the Boot Menu from the menu that appears.
Highlight the CD/DVD option and move it to the top of the list using the up arrow.
Insert the bootable disc into the drive tray.
Click [OK]. While the files are being loaded from the disc, a progress bar will appear at the bottom of the screen.
When the System Recovery Options dialog opens, select a new keyboard layout, if necessary, then click [Next].
85 - Restoring Your Pre-installed Software
7
8
9
10
Diagnostics tab: The Diagnostics tool is designed for use by IT professionals. It is not likely you will
need to use this tool. When you select devices from the Diagnosis window then click [Execute], several
tests are performed on the selected components.
Recovery tab: The Recovery tab contains three tools: Recovering User-Configured System Backups,
Restoring the Factory Image (only C: drive), and Restoring the Factory Image (full hard drive recovery).
You can use these tools to restore the Factory Image from the hidden partition, restore backup image(s)
you created or images stored on DVD discs, and perform a full hard drive recovery. Refer to instructions
above for details on how to create Factory Image Recovery DVDs, user backup DVDs and system image
backup.
Utility tab: The Utility tab contains three tools: Hard Disk Data Delete, Restore Recovery and Utility, and
Windows Complete PC Restore.
The Hard Disk Data Delete utility is used to delete all data on the hard disk and prevent the data
from being reused. NOTE: Do not use the Hard Disk Data Delete utility unless you are
absolutely certain that you want to erase your entire hard disk, including all partitions.
Restore Recovery and Utility allows you to restore the first hidden partition.
Windows Complete PC Restore utility allows you to restore an image created with Windows
Backup and Restore Center. Windows Complete PC Restore will overwrite the data on your hard
disk drive.
If you have installed a new hard drive or your hard drive is not bootable, perform the following steps. Note
that first you will need to create new partitions on the hard drive, then restore the Factory Image:
1
2
3
4
5
6
7
8
9
10
Power on your system. When the Fujitsu logo appears on the screen. press the [F12] key.
11
12
13
14
Click [Execute].
15 Click [Next] to begin the check. Click [Next] again when the check is complete.
16 2. Initializing hard disk drive will be in bold with the message Please insert the Bootable Disc into your optical
drive. Insert the bootable disc. Click [Next] to proceed. A dialog box appears, with a checking disc message.
17 Warning All DATA on the Hard Disk will be completely erased!!! will appear. Select [OK]. The partition creation
process will begin.
18 3. Restoring Factory Image to hidden partition will be in bold with the message Please insert the Recovery
Disk#1 into the optical drive. Click [Next] to proceed.
87 - Restoring Your Pre-installed Software
19 After completion, the tool will automatically go back to "3.Restoring Factory Image to hidden partition" but will
include the note "Please insert your Application Disc(s) starting with #1, then click [OK]. After installation of each
disc, insert the next and continue until all have been installed. If you don't have your Application Disc(s) or you
have inserted all your application discs. Please click [Cancel] to continue." At this point, you can either:
21 After clicking [Cancel], a confirmation message will appear "If you want to skip copying or copy has been
finished, click [OK]. Click [Cancel] to return to Restoring Factory Image to hidden partition."
Allows for manual driver update search. The first time it is used, you are prompted to agree to a user
agreement. After you click the icon, FDU automatically connects with the Fujitsu site to check for updates
and downloads them. While downloading, the icon has a red bar through it, indicating that it cannot be
used while the download is in process. When the update is complete, a message appears informing you.
Enable Automatic Update Notifications
Automatically searches for new updates on a regular basis (approximately every 3 days).
Show update history
Brings up a screen that displays a history of updates that have been made via the FDU.
About Fujitsu Driver Update
89 -
Chapter 5
THE SYSTEM CONTAINS COMPONENTS THAT CAN BE SEVERELY DAMAGED BY ELECTROSTATIC DISCHARGE (ESD).
TO MINIMIZE RISK TO THE COMPONENTS, OBSERVE THE FOLLOWING PRECAUTIONS:
BEFORE DOCKING OR UNDOCKING YOUR LIFEBOOK NOTEBOOK (WHEN USING A PORT REPLICATOR), IT
IS A GOOD PRACTICE TO ALWAYS TOUCH A GROUNDED METAL OBJECT TO DISCHARGE STATIC ELECTRICITY
BUILT UP IN YOUR BODY.
BE SURE TO POWER DOWN YOUR SYSTEM BEFORE ADDING OR REMOVING SYSTEM COMPONENTS. EVEN
IF THE SYSTEM IS IN HIBERNATE OR STANDBY STATES, DATA COULD BE LOST OR MEMORY COULD BE
DAMAGED IF POWER IS STILL AVAILABLE TO THE SYSTEM.
WHEN INSTALLING OR REMOVING A MEMORY MODULE, HOLD IT BY THE EDGE SO AS NOT TO TOUCH ANY
BE CAREFUL NOT TO TOUCH ANY INTERNAL COMPUTER TERMINALS OR
COMPONENTS; THE OIL FROM YOUR FINGERS COULD CAUSE A SHORT TO THE COMPONENTS.
CONTACTS OR CHIPS.
ELECTRICAL EQUIPMENT MAY BE HAZARDOUS IF MISUSED. OPERATIONS OF THIS PRODUCT OR SIMILAR PRODUCTS,
MUST ALWAYS BE SUPERVISED BY AN ADULT. DO NOT ALLOW CHILDREN ACCESS TO THE INTERIOR OF ANY
ELECTRICAL PRODUCTS AND DO NOT PERMIT THEM TO HANDLE ANY CABLES.
90
Your LIFEBOOK notebook is a durable but sensitive electronic device. Treat it with respect and
care.
Make a habit of transporting it in a suitable carrying case.
Do not attempt to service the computer yourself. Always follow installation instructions closely.
Keep it away from food and beverages.
To protect your notebook from damage and to optimize system performance, be sure to keep all air
vents unobstructed, clean, and clear of debris. This may require periodic cleaning, depending
upon the environment in which the system is used.
Do not operate the notebook in areas where the air vents can be obstructed, such as in tight
enclosures or on soft surfaces like a bed or cushion.
If you accidentally spill liquid on your LIFEBOOK notebook:
1
2
3
4
Turn it off.
Position it so that the liquid can run out.
Let it dry out for 24 hours, or longer if needed.
If your notebook will not boot after it has dried out, call your support representative.
Do not use your Fujitsu LIFEBOOK notebook in a wet environment (near a bathtub, swimming
pool).
Always use the AC adapter and batteries that are approved for your notebook.
Avoid exposure to sand, dust and other environmental hazards.
Do not expose your notebook to direct sunlight for long periods of time as temperatures above 140
F (60 C) may damage your notebook.
Keep the covers closed on the connectors and slots when they are not in use.
Do not put heavy or sharp objects on the computer.
If you are carrying your LIFEBOOK notebook in a briefcase, or any other carrying case, make sure
that there are no objects in the case pressing on the lid.
91 - Caring for your LIFEBOOK Notebook
Never position your notebook such that the optical drive is supporting the weight of the notebook.
Cleaning your LIFEBOOK notebook
Always disconnect the power plug. (Pull the plug, not the cord.)
Clean your LIFEBOOK notebook with a damp, lint-free cloth. Do not use abrasives or solvents.
Use a soft cloth to remove dust from the screen. Never use glass cleaners.
Always shut down the computer, unplug the power adapter, and remove the battery when cleaning
or disinfecting the computer exterior, keyboard or LCD display.
NOTE: Avoid wetting the thermal suede in all cases.
Cleaning guidelines using recommended off-the-shelf cleaners
USE OF INCORRECT CLEANERS CAN RESULT IN OPTICAL IMPAIRMENT OF THE LCD AND/OR DAMAGE
ALWAYS REFER TO THE CLEANER MANUFACTURER'S GUIDELINES AND MATERIAL
SAFETY DATA SHEETS FOR PROPER HANDLING AND USE OF THE PRODUCTS.
TO THE COMPUTER.
NEVER USE AMMONIA, ACIDIC, OR ALKALINE CLEANERS OR ORGANIC CHEMICALS SUCH AS PAINT
THINNER, ACETONE, PROPYL OR ISOPROPYL ALCOHOL, OR KEROSENE. IT MAY DAMAGE SURFACE
FINISHES AND THE COATING OF THE
LCD SCREEN.
NEVER USE COMPRESSED AIR FOR CLEANING STYLISTIC AND LIFEBOOK PCS.
IT IS POSSIBLE THAT THE UNIT MAY NOT AUTOMATICALLY GO TO POWER OFF OR HIBERNATE MODE
WHEN YOU CLOSE THE LID.
ATTEMPTING TO TRANSPORT THE COMPUTER WHILE POWER IS ON MAY DAMAGE THE NOTEBOOK DUE
TO SHOCK OR OVERHEATING SINCE THE AIR VENTS MAY BE BLOCKED OR RESTRICTED.
93 - Caring for your LIFEBOOK Notebook
Location
Outlet Type
Location
It is recommended that you carry your notebook with you while traveling, rather than checking it
in as baggage.
Never put your notebook through a metal detector. Have your notebook hand-inspected by security
personnel. You can however, put your notebook through a properly tuned X-ray machine. To avoid
problems, place your notebook close to the entrance of the machine and remove it as soon as
possible or have your notebook hand-inspected by security personnel. Security officials may
require you to turn your notebook on, so make sure you have a charged battery on hand.
Batteries
Caring for your Batteries
Power your LIFEBOOK notebook through the AC or optional auto/airline adapter whenever
possible.
If your notebook is running on battery power all day, connect it to the AC adapter overnight.
Keep brightness to the lowest level comfortable.
Turn off the Wireless LAN/Bluetooth devices when not in use by clicking the [Fn]+[F5] key
combination.
Set the power management for maximum battery life.
Put your notebook in Standby mode when it is turned on and you are not actually using it.
Limit your media drive access.
Disable the Media Player auto insert notification function.
Always use fully charged batteries.
Eject ExpressCards when not in use.
95 - Caring for your LIFEBOOK Notebook
Media Care
Caring for your Media (DVD/CD/CD-R)
Media discs are precision devices and will function reliably if given reasonable care.
Always store your media disc in its case when it is not in use.
Always handle discs by the edges and avoid touching the surface.
Avoid storing any media discs in extreme temperatures.
Do not bend media discs or set heavy objects on them.
Do not spill liquids or get dust on media discs.
Do not scratch media discs.
If a media disc is subjected to a sudden change in temperature, cold to warm condensation may form
on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room
temperature. DO NOT use a hair dryer or heater to dry media discs.
Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.
If a disc is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting
from the inner edge and wiping to the outer edge.
Your optical drive is durable but you must treat it with care. Please pay attention to the following points:
The drive rotates the compact disc at a very high speed. Do not carry it around or subject it to
shock or vibration with the power on.
Avoid using or storing the drive where it will be exposed to extreme temperatures or a damp or
dusty environment.
Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.
Avoid using or storing the drive where it will be subjected to shock or vibration.
Do not disassemble or dismantle the optical drive.
Use of a commercially available lens cleaner is recommended for regular maintenance of the drive.
96 - Caring for your LIFEBOOK Notebook
Media are durable, but you must treat them with care. The documentation supplied with your card will
provide specific information, but you should pay attention to the following points:
To keep out dust and dirt, store cards in their protective sleeves when they are not installed.
Avoid prolonged exposure to direct sunlight or excessive heat.
Keep the cards dry.
Do not flex or bend the cards, and do not place heavy objects on top of them.
Chapter 6
System Specifications
Specifications
This section provides the hardware and environmental specifications for your Fujitsu LIFEBOOK
notebook. Specifications of particular configurations will vary.
Configuration Label
The configuration label located on the bottom of your notebook contains specific information regarding the
options youve chosen for your notebook. Following is an example configuration label.
Part Number
Configuration ID
No: CP4xxxxxxxxxxx
Part No: FPC0xxxxxxxxxxxxx
LH531, 14.0WXGA, i5-2410M , W7Pro, DL S-MULTI, 4GB, 500G, LAN, WLAN/BT
Model #
Processor
Screen Size
Media Drive
Operating System
98
Hard Drive
Memory
Communications
Microprocessor
New 2nd generation Intel Core Processor (Refer to the system label to determine the model of your
processor).
Chipset
Intel HM65
Memory
System Memory
99 - Specifications
Video RAM (
Intel HD 3000 Graphics controller. The amount of shared video memory is determined by the amount
of system memory, as follows:
System Memory
(Windows 7 32-bit)
Maximum
Graphics Memory
System Memory
(Windows 7 64-bit)
Maximum
Graphics Memory
1 GB
274 MB
1 GB
274 MB
2 GB
786 MB
2 GB
786 MB
4 GB
1430 MB
4 GB
1696 MB
Audio
Realtek codec ALC269 with 2-channel High Definition (HD) audio.
Headphones: Stereo headphone/line-out jack, 3.5 mm, 1 Vrms or less, min. impedance 32
Microphone: Stereo microphone/line-in jack, 3.5 mm, 100 mVp-p or less, min. impedance 10K
Two built-in boxless stereo speakers
Mass Storage Device Options
Hard Drive
Serial ATA, 5400 rpm, 2.5. The hard drive capacity and speed is dependent upon the system
configuration.
Optical Drive
Depending upon your system configuration, one of the following optical drives may be installed:
Dual-Layer Multi-Format Blu-ray Combo Drive: Write: 8x DVD-R (SL), 8x DVD+R (SL), 6x
DVD-R (DL), 6x DVD+R (DL), 6x DVD-RW, 8x DVD+RW, 5x DVD-RAM, 24x CD-R, 6x CD-RW (US,
US+)
100 - Specifications
Power
Battery
Autosensing 100-240V AC, supplying 19V DC, 3.16A, 60W to the LIFEBOOK; includes an AC cable
Power Management
Adobe Reader
Norton Internet Security (60-day free trial)
Roxio Creator
CyberLink YouCam
CyberLink MakeDisc
CyberLink PowerDirector
CyberLink PowerDVD
Google Toolbar
103 - Specifications
All operating systems and most application software have tutorials built into them upon installation. We
highly recommend that you step through the tutorial before you use an application.
Manuals
Included with your notebook you will find manuals for your installed operating system and other preinstalled software. Any manuals that are not included, are available online through the help system of the
software. We recommend that you review these manuals for information on the use of these applications.
Adobe Reader
Adobe Reader allows you to view, navigate, and print PDF files across all major computing platforms.
Roxio Creator
Roxio Creator lets you burn CDs and organize, edit and share digital photos, music, data, or videos.
Norton Internet Security
Your system includes a free 60-day trial version of Symantecs Norton Internet Security. Internet
Security is a suite of tools designed to protect your notebook from computer viruses, hackers, spyware,
and spam. It assists in the protection of data currently on your hard disk from destruction or contamination.
The trial version is activated upon your acceptance of software license agreement. After 60 days, you will
need to purchase a subscription from Symantec to download latest virus, spyware, and spam definitions.
CyberLink PowerDVD
CyberLink MakeDisc allows you to burn data, videos and photographs to CDs or DVDs.
104 - Specifications
CyberLink PowerDirector
CyberLink PowerDirector allows you to edit and enhance your videos, and add special effects to them.
CyberLink YouCam
CyberLink YouCam allows you to capture photos or movies on the embedded webcam, add special effects
to them, and share them in a variety of formats or via social networks.
Google Toolbar
Google Toolbar lets you to search the Internet quickly, block pop-ups, and perform a variety of other tasks
to make your Internet experience easier and more pleasant.
Microsoft Windows Live Essentials
Windows Live Essentials is a suite of programs that make it easier and more enjoyable to use your LIFEBOOK. Live Essentials consists of six Live applications: Messenger, Photo Gallery, Writer, Mail, Movie
Maker, and Silverlight. Messenger lets you quickly communicate and interact with individuals and
groups. Photo Gallery is a flexible application that lets you organize, edit, and share your photos. Writer
can be used to generate blog entries, upload videos and photos to your blogs, and publish your entries
online. Mail makes it easy for you to manage your email accounts. Movie Maker makes great-looking
movies and slideshows from your videos and photos. Its simple to import standard or high definition
video and photos, and then have AutoMovie add animations, music, and a title in minutes. Silverlight
powers rich application experiences and delivers high quality, interactive video across the Web and
mobile devices.
Microsoft Office Starter 2010
Microsoft Office Starter 2010 is a software suite containing reduced-functionality versions of Word 2010
and Excel 2010 with advertising. PowerPoint, Outlook and Publisher are NOT included. Purchase an
Office 2010 Product Key Card to activate full-featured Office software on this PC.
105 - Specifications
Glossary
AC Adapter
A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your
LIFEBOOK notebook.
Access point
Wireless network device used to bridge wireless and wired network traffic.
ACPI
A type of technology for making flat-panel displays which has a transistor or similar device for every
pixel on the screen.
Ad Hoc Mode
Ad Hoc Mode refers to a wireless network architecture where wireless network connectivity between
multiple computers is established without a central wireless network device, typically known as
Access Points. Connectivity is accomplished using only client devices in a peer-to-peer fashion. For
details, refer to on Ad Hoc Mode on page 125
ADSL
Asymmetric Digital Subscriber Line. Technology for transporting high bit-rate services over ordinary
phone lines.
106
AGP
Accelerated Graphics Port. Graphics port specifically designed for graphics-intensive devices, such as
video cards and 3D accelerators.
Auto/Airline Adapter
A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power
outlet to the DC voltage needed to power your LIFEBOOK notebook.
BIOS
Basic Input-Output System. A program and set of default parameters stored in ROM which tests and
operates your LIFEBOOK notebook when you turn it on until it loads your installed operating system
from disk. Information from the BIOS is transferred to the installed operating system to provide it with
information on the configuration and status of the hardware.
Bit
An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).
bps
An abbreviation for bits per second. Used to describe data transfer rates.
Boot
To start-up a computer and load its operating system from disk, ROM or other storage media into
RAM.
Bus
An electrical circuit which passes data between the CPU and the sub-assemblies inside your
LIFEBOOK notebook.
Byte
107 - Glossary
Cache Memory
A block of memory built into the micro-processor which is much faster to access than your system
RAM and used in specially structured ways to make your overall data handling time faster.
CardBus
A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI
architecture.
CD-ROM
Compact disk read only memory. This is a form of digital data storage which is read optically with a
laser rather than a magnetic head. A typical CD-ROM can contain about 600MB of data and is not
subject to heads crashing into the surface and destroying the data when there is a failure nor to wear
from reading.
Channel
Range of narrow-band frequencies used by the WLAN device to transmit data. IEEE802.11b/g - 11
channels, 22 MHz wide channels.
CMOS RAM
Complementary metal oxide semiconductor random access memory. This is a technology for
manufacturing random access memory which requires very low levels of power to operate.
COM Port
An instruction which you give your operating system. Example: run a particular application or format
a floppy disk.
Configuration
The combination of hardware and software that makes up your system and how it is allocated for use.
108 - Glossary
CRT
Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent
screen. It produces a visual image by varying the position and intensity of the beam.
Data
Direct current. A voltage or current that does not fluctuate periodically with time.
Default Value
Dynamic Host Configuration Protocol. A protocol used to automatically acquire parameters required
for the communication, such as IP address. The sender of IP address is called a DHCP server, and the
receiver is called a DHCP client.
DIMM
A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is
highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly
called a diskette.
Disk Drive
The hardware which spins the disk and has the heads and control circuitry for reading and writing the
data on the disk.
Diskette
DMA
Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require
CPU action.
DMI
Domain Name System. A function to control the association between the IP address and the name
assigned to the computer. If you do not know the IP address but if you know the computer name, you
can still communicate to that computer.
Driver
A computer program which converts application and operating system commands to external devices
into the exact form required by a specific brand and model of device in order to produce the desired
results from that particular equipment.
DVMT
Dynamic Video Memory Technology. A video memory architecture that increases the efficiency of the
motherboard by using innovative memory utilization and direct AGP.
ECP
Extended Capability Port. A set of standards for high speed data communication and interconnection
between electronic devices.
Encryption Key (Network Key)
Data encryption key used to encrypt message text and for computing message integrity checks. Data
encryption protects data from unauthorized viewing.
This device uses the same encryption key to encode and decode the data, and the identical encryption
key is required between the sender and receiver.
110 - Glossary
ESD
Electro-Static Discharge. The sudden discharge of electricity from a static charge which has built-up
slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing
hair on a dry day.
FCC
A spinning platter of magnetic data storage media where the platter is very stiff.
I/O
The connector and associated control circuits for data entering and leaving your notebook in electronic
form.
IDE
Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive
unit.
IEEE802.11a
Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11a devices operate in the
5 GHz lower and middle UNII bands.
IEEE802.11b
Wireless LAN standard that supports a maximum data rate of 11 Mbps. 802.11b devices operate in the
2.4 GHz ISM band.
111 - Glossary
IEEE802.11g
Wireless LAN standard that supports a maximum data rate of 54 Mbps. 802.11g devices operate in the
2.4 GHz ISM band.
Infrared
Light just beyond the red portion of the visible light spectrum which is invisible to humans.
Infrastructure
A name of a wireless LAN configuration. This type of communication uses an access point. Another
type of communication is called Ad Hoc.
IP Address
An identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol
route messages based on the IP address of the destination. The format of an IP address is a 32-bit
numeric address written as four numbers separated by periods. Each number can be zero to 255. For
example, 1.160.10.240 could be an IP address.
Within an isolated network, you can assign IP addresses at random as long as each one is unique.
However, connecting a private network to the Internet requires using registered IP addresses (called
Internet addresses) to avoid duplicates.
The four numbers in an IP address are used in different ways to identify a particular network and a
host on that network. Three regional Internet registries -- ARIN, RIPE NCC and APNIC -- assign
Internet addresses from the following three classes.
Class A - supports 16 million hosts on each of 126 networks
Class B - supports 65,000 hosts on each of 16,000 networks
Class C - supports 254 hosts on each of 2 million networks
The number of unassigned Internet addresses is running out, so a new classless scheme called CIDR
is gradually replacing the system based on classes A, B, and C and is tied to adoption of IPv6.
IR
IrDA
Infrared Data Association. An organization which produces standards for communication using
infrared as the carrier.
IRQ
Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred
which needs to be processed.
KB
Local Area Network. An interconnection of computers and peripherals within a single limited
geographic location which can pass programs and data amongst themselves.
LCD
Liquid Crystal Display. A type of display which makes images by controlling the orientation of
crystals in a crystalline liquid.
Lithium ion Battery
A type of rechargeable battery which has a high power-time life for its size and is not subject to the
memory effect as Nickel Cadmium batteries.
MAC Address
Media Access Control Address. A unique physical address of a network card. For Ethernet, the first
three bytes are used as the vendor code, controlled and assigned by IEEE. The remaining three bytes
are controlled by each vendor (preventing overlap), therefore, every Ethernet card is given a unique
physical address in the world, being assigned with a different address from other cards. For Ethernet,
frames are sent and received based on this address.
MB
Megahertz
A repository for data and applications which is readily accessible to your LIFEBOOK notebooks
CPU.
MHz
Megahertz.
MIDI
A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data
terminal to a communication line.
Monaural
Data that is used for encrypting data in data communication. The personal computer uses the same
network key both for data encryption and decryption, therefore, it is necessary to set the same network
key as the other side of communication.
114 - Glossary
When a wireless LAN network is configured, grouping is performed to avoid interference or data theft.
This grouping is performed with Network name (SSID). In order to improve security, the network
key is set allowing no communication unless Network name (SSID) coincides with the network key.
NTSC
National TV Standards Commission. The standard for TV broadcast and reception for the USA.
Open system authentication
Null authentication method specified in the 802.11 standard that performs no authentication checks on
a wireless client before allowing it to associate.
Operating System
A group of control programs that convert application commands, including driver programs, into the
exact form required by a specific brand and model of microprocessor in order to produce the desired
results from that particular equipment.
Partition
A block of space on a hard drive which is set aside and made to appear to the operating system as if it
were a separate disk, and addressed by the operating system accordingly.
PCMCIA
PCMCIA is a trademark of the Personal Computer Memory Card International Association. The
Personal Computer Memory Card International Association is an organization that sets standards for
add-in cards for personal computers.
Peripheral Device
A piece of equipment which performs a specific function associated with but not integral to a
computer. Examples: a printer, a modem, a CD-ROM.
Pitch (keyboard)
Pixel
The smallest element of a display, a dot of color on your display screen. The more pixels per area the
clearer your image will appear.
POST
Power On Self Test. A program which is part of the BIOS which checks the configuration and
operating condition of your hardware whenever power is applied to your notebook. Status and error
messages may be displayed before the operating system is loaded. If the self test detects failures that
are so serious that operation can not continue, the operating system will not be loaded.
PPPoE
Point to Point Protocol over Ethernet. A protocol for Ethernet, using a Point-to-Point Protocol (PPP),
which is used for connection on the phone line.
Program
An integrated set of coded commands to your computers telling your hardware what to do and how
and when to do it.
Protocol
Procedures and rules use to send and receive data between computers.
It is also a method of sending and receiving data and a process used to handle communication errors
Conditions required for communication are organized in procedures for correct transfer of
information.
RAM
Random Access Memory. A hardware component of your LIFEBOOK notebook that holds binary
information (both program and data) as long as it has the proper power applied to it.
RAM Module
A printed circuit card with memory and associated circuitry which allows the user to add additional
memory to the computer without special tools.
116 - Glossary
Reset
The act of reloading the operating system. A reset erases all information stored in RAM.
Restart
See Reset.
Resume
To proceed after interruption. In your notebook this refers to returning to active operation after having
been in one of the suspension states.
ROM
Read Only Memory. A form of memory in which information is stored by physically altering the
material. Data stored in this way can not be changed by your notebook and does not require power to
maintain it.
SDRAM
A connection to another device through which data is transferred one bit at a time on a single wire with
any other wires only for control of the device not for transfer of data.
Shared key authentication
802.11 network authentication method in which the AP sends the client device a challenge text packet
that the client must then encrypt with the correct WEP key and return to the AP. If the client has the
wrong key or no key, authentication will fail and the client will not be allowed to associate with the
AP. Shared key authentication is not considered secure, because a hacker who detects both the cleartext challenge and the same challenge encrypted with a WEP key can decipher the key.
117 - Glossary
SSID
Service Set Identifier, a 32-character unique identifier attached to the header of packets sent over a
WLAN that acts as a password when a mobile device tries to connect to the BSS. The SSID
differentiates one WLAN from another, so all access points and all devices attempting to connect to a
specific WLAN must use the same SSID. A device will not be permitted to join the BSS unless it can
provide the unique SSID. Because the SSID is broadcast in plain text, it does not supply any security
to the network.
Standby
To make inoperative for a period of time. Your LIFEBOOK notebook uses various suspension states
to reduce power consumption and prolong the charge of your battery.
Status Indicator
A display which reports the condition of some portion of your hardware. On your LIFEBOOK
notebook this is an LCD screen just above the keyboard.
Stereo (audio)
A system using two channels to process sound from two different sources.
Subnet mask
TCP-IP network is controlled by being divided into multiple smaller networks (subnets). IP address
consists of the subnet address and the address of each computer. Subnet mask defines how many bits
of IP address comprise the subnet address. The same value shall be set among computers
communicating with each other.
S-Video
An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted
to provide time of day and date.
118 - Glossary
TCP/IP
Transmission Control Protocol/Internet Protocol. A standard Internet protocol that is most widely
used.
TFT
Thin Film Transistor A technology for flat display panels which uses a thin film matrix of transistors
to control each pixel of the display screen individually.
UL
Underwriters Laboratories An independent organization that tests and certifies the electrical safety
of devices.
USB
Universal Serial Bus. Standard that allows you to simultaneously connect up to 127 USB devices such
as game pads, pointing devices, printers, and keyboards to your computer.
VRAM
Video Random Access Memory. A memory dedicated to video display data and control.
WFM
Wired for Management is Intels broad-based initiative to reduce the total cost of ownership (TCO) of
business computing without sacrificing power and flexibility.
Wi-Fi Compatible
Wi-Fi (Wireless Fidelity) Identifies that the product has passed the interoperability test, supplied by
the WECA (Wireless Ethernet Compatibility Alliance), which guarantees the interoperability of
wireless IEEE 802.11 LAN products. For more information on the Wi-Fi standard, go to the WECA
Web site at: www.wirelessethernet.com.
WLAN
Wireless Local Area Network. A wireless interconnection of computers and peripherals within a
single limited geographic location which can pass programs and data amongst themselves.
119 - Glossary
Regulatory Information
Notice
Changes or modifications not expressly approved by Fujitsu could void this users authority to operate the
equipment.
FCC NOTICES
Notice to Users of Radios and Television
This equipment has been tested and found to comply with the limit for class B digital devices, pursuant to
parts 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet that is on a different circuit than the receiver.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables must be employed with this equipment to ensure compliance with the
pertinent RF emission limits governing this device.
DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television
On board an airplane, or
In an explosive environment, or
In situations where the interference risk to other devices or services is perceived or identified as harmful.
In cases in which the policy regarding use of Wireless LAN devices in specific environments is not clear (e.g., airports,
hospitals, chemical/oil/gas industrial plants, private buildings), obtain authorization to use these devices prior to operating the
equipment.
Regulatory Information/Disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with the instructions included in the user
documentation provided with the product. Any changes or modifications made to this device that are not expressly approved
by the manufacturer may void the users authority to operate the equipment. The manufacturer is not responsible for any radio
or television interference caused by unauthorized modification of this device, or the substitution or attachment of connecting
121
cables and equipment other than those specified by the manufacturer. It is the responsibility of the user to correct any
interference caused by such unauthorized modification, substitution or attachment. The manufacturer and its authorized
resellers or distributors will assume no liability for any damage or violation of government regulations arising from failure to
comply with these guidelines.
This device must not be co-located or operated in conjunction with any other antenna or transmitter.
1
2
3
4
122 -
Export restrictions
This product or software contains encryption code which may not be exported or transferred from the US or Canada without
an approved US Department of Commerce export license. This device complies with Part 15 of FCC Rules., as well as ICES
003 B / NMB 003 B. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesirable operation.
Modifications not expressly authorized by Fujitsu America may invalidate the user's right to operate this equipment.
Canadian Notice
The device for the 5150 - 5250 MHz band is only for indoor usage to reduce the potential for harmful interference to co-channel
mobile satellite systems.
The maximum antenna gain of 6 dBi permitted (for devices in the 5250 - 5350 MHz, 5470 - 5725 MHz and 5725 - 5825 MHz
bands) to comply with the e.i r.p. limit as stated in A9.2 of RSS210.
In addition, users are cautioned to take note that high power radars are allocated as primary users (meaning they have priority)
of 5250 - 5350 MHz and 5650 - 5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
123 -
The WLAN device is capable of four operating modes, IEEE802.11b, IEEE802.11g, and IEEE802.11n.
The WLAN device is Wi-Fi certified and operate (as applicable) at a the maximum data rate of 540 Mbps
(theoretical) in IEEE802.11n mode; 54 Mbps in IEEE802.11g mode; and 11 Mbps in IEEE802.11b mode.
The WLAN device supports the following encryption methods - WEP, TKIP, CKIP, and AES encryption.
The Wireless LAN device is compliant with the following standards: WPA, WPA2, CCX1.0, CCX2.0, CCX3.0,
and CCX4.0.
Ad Hoc Mode refers to a wireless network architecture where wireless network connectivity between
multiple computers is established without a central wireless network device, typically known as Access
Point(s). Connectivity is accomplished using only client devices in a peer-to-peer fashion. That is why Ad
Hoc networks are also known as peer-to-peer networks. Ad Hoc networks are an easy and inexpensive
method for establishing network connectivity between multiple computers.
Ad Hoc mode requires that the SSID (service set identifier), network authentication, and encryption key
settings are identically configured on all computers in the Ad Hoc network.
Infrastructure mode refers to a wireless network architecture in which devices communicate with wireless
or wired network devices by communicating through an Access Point. In infrastructure mode, wireless
devices can communicate with each other or with a wired network. Corporate wireless networks operate
in infrastructure mode because they require access to the wired LAN in order to access computers,
devices, and services such as file servers, printers, and databases.
Access Point (Infrastructure) Mode Network
Internet
Wired LAN
ADSL modem,
cable modem,
or similar
Access Point*
Wireless LAN
*An optional hub for a wired
LAN may be required depending
upon the type of access point used.
The WLAN device is an optional device that may come pre-installed in your mobile computer. Under
normal circumstances, it should not be necessary for you to remove or re-install it. The Operating System
that your mobile computer comes with has been pre-configured to support the WLAN device.
Wireless Network Considerations
The WLAN device supports IEEE802.11b, IEEE802.11g, and IEEE802.11n.
The WLAN device operates in the 2.4 GHz ISM band.
Microwave ovens may interfere with the operation of WLAN devices since they operate in the same 2.4 GHz
frequency range as IEEE802.11b/g/n devices.
Wireless devices that transmit in the 2.4 GHz range may interfere with operation of WLAN devices in
IEEE802.11b/g/n modes. Symptoms of interference include reduced throughput, intermittent disconnects,
and many frame errors. It is HIGHLY recommended that these interfering devices be powered off to ensure
proper operation of the WLAN device.
Wireless
Device
Switch
Note that disconnecting via the icon in the system tray does not turn off the radio; it continues to transmit
and receive even though its not connected.
1
2
Right-click the WLAN icon in the taskbar at the bottom right of your screen.
Choose Disconnect from a network.
3
4
5
6
7
Enter the required information. You may need to consult with your network administrator for some information.
If the Control Panel is not in Classic View, select Classic View from the left panel. Double-click the Network and
Sharing Center icon.
Click on the [Add] button.
Depending upon what type of connection you would like to make, make a selection. For an infrastructure
network, select Manually create a network profile. For ad hoc network, select Create an ad hoc network.
In the event you require assistance, go to the Network and Sharing Center window (Start -> Control Panel ->
Network and Sharing Center), and type in relevant keywords in the Search box.
Connecting to a Network
After you have configured your computer, you can connect to an active network by performing the
following steps:
1
2
3
Possible Cause
Possible Solution
Unavailable
network
connection
Problem
Possible Cause
Possible Solution
Unavailable
network
connection
(continued)
The computer to be
connected is turned off
RF interference from
Access Points or other
wireless networks
Wireless network
authentication has
failed
Incorrectly configured
network settings
Incorrect IP address
configuration
WLAN Specifications
Item
Specification
Type of network
Transfer rate
Active frequency
Number of channels
802.11n:
2.4 GHz - 3 non-overlapping channels when Channel Bonding is not used; 2
non-overlapping channels when Channel Bonding is used.
Security
*
Wi-Fi based indicates that the interconnectivity test of the organization which guarantees the
interconnectivity of wireless LAN (Wi-Fi Alliance) has been passed.
**
The communication ranges shown above will increase or decrease depending on factors such as
number of walls, reflective material, or interference from external RF sources.
***
Encryption with network key (WEP) is performed using the above number of bits, however, users
can set 40 bits/104 bits after subtracting the fixed length of 24 bits.
****
Depending on practical environments, the allowable number of computers to be connected may be
decreased.
1
2
3
4
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The Bluetooth antenna is located on the front edge of the right palm rest and is exempt from minimum
distance criteria due to its low power.
The transmitters in this device must not be co-located or operated in conjunction with any other antenna
or transmitter.
Canadian Notice
To prevent radio interference to the licensed service, this device is intended to be operated indoors and
away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.
Warranty
Users are not authorized to modify this product. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or changed in any way without signed written permission
from Fujitsu. Unauthorized modification will void the equipment authorization from the FCC and
Industry Canada and the warranty.
136
IF YOU PURCHASED A SYSTEM WITH AN INTEL WIRELESS LAN AND OPTIONAL INTEL WIDI TECHNOLOGY, THE
WIDI APPLICATION MAY OR MAY NOT BE PRE-INSTALLED (DEPENDING UPOON YOUR SYSTEM CONFIGURATION).
SYSTEMS WITH INTEL WIDI PRE-INSTALLED WILL HAVE A WIDI ICON LOCATED ON THEIR DESKTOP. IF THE ICON
IS NOT PRESENT, INTEL WIDI WILL BE INSTALLED AS SOON AS YOU RUN CLICKME.
THE INTEL WIDI TECHNOLOGY WILL ONLY WORK IN COMBINATION WITH AN INTEL WIRELESS LAN.
THERE MAY BE A SLIGHT TIME LAG WHEN USING WIDI WHEN YOU MOVE THE MOUSE OR TYPE IN CHARACTERS.
ONLY WINDOWS MEDIA PLAYER CAN BE USED AS THE MEIA PLAYER FOR WIDI 2.0.
BEFORE USING INTEL WIDI, BE SURE THAT THE SYSTEMS WIRELESS DEVICE SWITCH IS TURNED ON.
NOTE THAT SECURE CONTENTS ARE NOT SUPPORTED BY INTEL WIDI 2.0. CONTENT REQUIRING OUTPUT
PROTECTION SUCH AS BLU-RAY AND DVD MOVIE PLAYBACK IS NOT SUPPORTED BY WIDI.
THE FIRST TIME YOU USE WIDI, THE DEFAULT DISPLAY RESOLUTION IS 1280X720. IF YOU WOULD LIKE TO
CHANGE THE RESOLUTION, GO TO THE CONTROL PANEL -> DISPLAY PROPERTIES UNDER THE SETTINGS TAB.
ONCE YOU HAVE SET THE RESOLUTION, IT WILL BECOME THE DEFAULT UNLESS YOU CHANGE IT AGAIN.
Verify that you have a display adapter connected to the television on which you want to use WiDi and turn on
the television.
2
3
4
If you havent yet turned on the wireless device switch on your notebook, do so now.
Click on the WiDi icon on your desktop or the Start menu shortcut.
The PC content is displayed on the big screen TV.
After the initial set-up between the laptop and a compatible display adapter, you can set the adapter as the
default to auto-connect. In the future, simply opening the application will automatically connect the two.
For detailed information about using and troubleshooting the WiDi technology, click on the WiDi icon
then click the [Help] button in the upper right-hand corner to open the Wireless Display Help file.
Index
BIOS 38
Bluetooth 134
Built-in Speakers 70
A
About This Guide 7
AC
adapter 33
plug adapters 94
Air Vents 18
Anti-theft lock slot 16
Anytime USB Charge 64
Auto/Airline Adapter 33
C
Camera 11
CapsLock 21
CD-ROM 70, 71
Click Me! 39
Clicking 26
Cold-swapping 48
Configuration Label 98
Connecting the Power Adapters 33
Controls and Connectors 11
Conventions Used in the Guide 7
Cursor 25
Cursor Keys 23
B
Battery 45
alarm 47
bay 18
care 95
Charge/DC-In Indicator 19
cold-swapping 48
conserving power 41
dead 74
faulty 74
hot-swapping 48
increasing life 95
Level Indicator 20
lithium ion battery 45
low 47
problems 74, 75
recharging 46
shorted 47
Standby mode 47
D
DC Power Jack 33
Device Ports 63, 101
Digital Microphone 12
DIMM 59
Display Panel 12, 34
adjusting 35
brightness 35
closing 35
opening 34
problems 76, 77
138
K
Keyboard 12, 22
cursor keys 23
function keys 23
numeric keypad 22
problems 71
Windows keys 23
E
ECO mode 24
Error Messages 79
External Video Port 14
L
LAN (RJ-45) Jack 16
Line-In Jack 64
Line-Out Jack 63
Lithium ion Battery 45
F
FDU 40, 89
Fujitsu Contact Information 8
Fujitsu Driver Update utility 40, 89
Function Key
F10 24
F3 24
F4 24
F6 24
F7 24
F8 24, 31
F9 24, 31
FN 24
M
Media Player
battery power 55
care 96
Control Panel 55
loading 51
removing 54
Software 51, 54
using 55
Memory
capacity 61
compartment 17, 60
installing 59
problems 72
removing 61
upgrade module 59
Memory Stick
installing 58
removing 58
Microphone 12
Microphone Jack 64
H
Hard Disk Drive
access indicator 21
problems 71
Headphone Jack 63
Hibernation Feature 42
Hot-swapping 48
I
Internal LAN 63
139
SDRAM 17, 59
Secure Digital Card 58
Sleep Mode 41
Specifications 98
Audio 100
Chipset 99
Dimensions and Weight 102
Environmental Requirements 103
Keyboard 102
Mass Storage Device Options 100
Memory 99
Microprocessor 99
Power 102
Video 99
Status Indicator Panel 13, 19
Stereo Speakers 13
Support Button 13
N
NumLk 21
O
Optical Drive 16, 50
Modular Multi-Format DVD Writer 50
release button 16
tray release 54
P
Power
AC adapter 33
Auto/Airline adapter 33
failure 73
management 41
off 43
on 36
problems 75
sources 33
Power Management 41
Power On Self Test 36, 79
Power/Suspend/Resume Button 12
Pre-Installed Software 104
T
Touchpad 25
buttons 25
controls 29
Touchpad Pointing Device 13
Troubleshooting 67
Registration 40
Restarting 43
Restoring Your Pre-installed Software 80
RJ-45 63
V
Volume control 31
S
ScrLk 21
SD Card
installing 58
removing 58
140
W
Warranty 9
Web Camera 11
Windows keys 23
Application key 23
Start keys 23
Windows Power Management 43
Wireless LAN
activating 128
Ad Hoc Mode 125
Before Using the Wireless LAN 124
characteristics 124
configuring 128
connection to the network 129
deactivating 127
disconnecting 128
Infrastructure Mode 126
modes 125
Specifications 132
Troubleshooting 129
Wireless LAN Glossary 130
Wireless LAN On/Off Switch 13
141
Guide
dutilisation
Dcouvrez comment
utiliser votre ordinateur
portable Fujitsu
LIFEBOOK LH531
AVERTISSEMENT
LA MANIPULATION DU CORDON DE CE PRODUIT VOUS EXPOSE AU PLOMB, UNE SUBSTANCE CHIMIQUE QUI,
SELON LTAT DE CALIFORNIE, PEUT CAUSER DES ANOMALIES CONGNITALES OU DAUTRES PROBLMES
DE REPRODUCTION.
LAVEZ-VOUS LES MAINS APRS CHAQUE MANIPULATION.
DCLARATION DE CONFORMIT
selon la partie 15 des rgles de la FCC
Nom de la partie responsable : Fujitsu America, Inc.
Adresse :
Tlphone :
(408) 746-6000
Cet appareil est conforme aux exigences de la partie 15 des rgles de la FCC. Lutilisation est soumise aux deux
conditions suivantes : (1) cet appareil ne doit pas causer dinterfrence nuisible ; (2) cet appareil doit accepter toutes
les interfrences reues, y compris celles pouvant causer un mauvais fonctionnement de lappareil.
Pendant lutilisation de lordinateur portable, observez toujours les consignes de scurit lmentaires ci-aprs afin de rduire au minimum
le risque dincendie, dlectrocution ou dautres blessures. Dautre part :
Nutilisez pas ce produit proximit dun point deau (baignoire, lavabo, vier de cuisine, vier de buanderie) ni dans un sous-sol
humide ou ct dune piscine.
Utilisez uniquement le cordon dalimentation et les piles recommands dans ce manuel. Ne jetez pas les batteries dans le feu. Elles
risquent dexploser. Vrifiez si la rglementation locale comporte des instructions spciales dlimination.
CONSERVEZ CES INSTRUCTIONS
POUR BNFICIER DUNE PROTECTION CONTINUE CONTRE LES RISQUES DINCENDIE, LE FUSIBLE NE DOIT
TRE REMPLAC QUE PAR UN AUTRE FUSIBLE DE MME TYPE ET DE MME CAPACIT.
Recyclage de la batterie
Avec le temps, lautonomie des batteries qui alimentent votre ordinateur portable finira par diminuer ; cest un phnomne naturel pour toutes
les batteries. Lorsque vous remarquerez cela, songez installer une batterie neuve*. Si vous remplacez votre ancienne batterie, il est important
que vous la jetiez comme il convient car, dans le cas contraire, les matriaux quelle contient risquent de nuire lenvironnement.
Chez Fujitsu, nous portons une attention particulire la protection de lenvironnement et nous collaborons donc avec la
Rechargeable Battery Recycle Corporation (RBRC*), une organisation de service publique but non lucratif qui sengage
dans la protection de lenvironnement en recyclant les batteries et piles usages sans aucun frais pour vous.
La RBRC dispose de dizaines de milliers de points de collecte aux tats-Unis et au Canada. Pour trouver le lieu de collecte
le plus proche de chez vous, visitez www.RBRC.org ou appelez au 1-800-822-8837.
Si aucun des lieux proposs par la RBRC ne vous convient, vous pouvez en trouver un en visitant le site de la Consumer Education Initiative
(Initiative pour lducation des consommateurs) de lEIA ladresse http://EIAE.org/.
Rappelez-vous que la protection de lenvironnement est laffaire de tous, vous devriez donc faire tout votre possible afin dy contribuer, pour
la gnration actuelle et les gnrations suivantes.
*
Pour commander une nouvelle batterie compatible avec votre ordinateur portable Fujitsu, visitez le site www.shopfujitsu.com si vous
rsidez aux tats-Unis ou www fujitsu.ca/products/notebooks si vous rsidez au Canada.
** La RBRC est une organisation indpendante dont Fujitsu finance une partie des activits de recyclage ; la RBRC nest en aucune faon
affilie Fujitsu.
5-
Chapitre 1
11
14
16
17
19
20
21
21
21
Clavier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Utilisation du clavier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Rglage du volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Rglage du volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapitre 2
cran . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ouverture de lcran . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Rglage de la luminosit de lcran . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Utilisation du clavier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Utilisation des options dalimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
laide du Centre de mobilit Windows . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Fermeture de lcran . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Gestion de lalimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Bouton dalimentation/veille/reprise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Mode sommeil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Mode veille prolonge (enregistrement sur le disque) . . . . . . . . . . . . . . . . 42
Gestion de lalimentation dans Windows . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Redmarrage du systme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Mise hors tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapitre 3
Lecteur optique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Logiciels du lecteur multimdia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Installation dun disque dans votre lecteur . . . . . . . . . . . . . . . . . . . . . . . . . 51
Retrait dun disque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Ouverture durgence du plateau de chargement du lecteur optique . . . . . . 54
Utilisation des logiciels du lecteur multimdia . . . . . . . . . . . . . . . . . . . . . 54
Utilisation du lecteur multimdia avec alimentation par batterie . . . . . . . . 55
Ports de priphriques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Prise de rseau local (RJ-45) interne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Prise dcouteurs/sortie de ligne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Prise micro/entre de ligne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3
Ports USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Port vido externe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Chapitre 4
Chapitre 5
Entretien
Entretien de votre ordinateur portable LIFEBOOK. . . . . . . . . . . . . . . . . 94
Nettoyage de votre ordinateur portable LIFEBOOK . . . . . . . . . . . . . . . . . 96
Rangement de votre ordinateur portable LIFEBOOK . . . . . . . . . . . . . . . . 97
Voyager avec votre ordinateur portable LIFEBOOK. . . . . . . . . . . . . . . . . 98
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Entretien de votre lecteur multimdia. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Cartes MemoryStick/SD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Chapitre 6
Spcifications techniques
Spcifications techniques du systme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
tiquette de configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Microprocesseur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Puce. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Mmoire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Vido. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Options de mmoire de masse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Caractristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Ports de priphriques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Clavier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Alimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Dimensions et poids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Environnement dexploitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Accessoires prfrs des utilisateurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Logiciels fournis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Apprendre utiliser vos logiciels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Prface
propos de ce guide
Lordinateur portable LIFEBOOK LH531 de Fujitsu America offre toutes les performances dun
ordinateur de bureau grce au nouveau processeur Intel Core de deuxime gnration. Cet ordinateur
portable est dot dun cran couleur haute dfinition WXGA de 14 pouces. Il vous permet daccder la
puissance informatique dun ordinateur de bureau dans un environnement portable.
Votre ordinateur est livr avec le systme dexploitation Microsoft Windows 7 dition Familiale
Suprieure, pr-install.
Ce manuel prsente le mode demploi de lordinateur portable LIFEBOOK et de ses logiciels intgrs.
Conventions utilises dans ce guide
Les touches du clavier et lcran apparaissent entre crochets. Exemple : [Fn], [F1], [chap], [Entre] et [Ctrl].
Le texte contient plusieurs renvois vers des pages contenant des informations supplmentaires sur un sujet
quelconque. Exemple : ( Voir Procdure dinstallation en page 43 ).
Les lments des menus lcran sont indiqus en caractres gras. Exemple : Cliquez sur Menu Fujitsu,
puis faites votre slection.
LICNE DINFORMATIONS MET EN VIDENCE DES RENSEIGNEMENTS QUI VOUS AIDERONT MIEUX
COMPRENDRE LE SUJET TRAIT.
LICNE DE MISE EN GARDE MET EN VIDENCE DES INFORMATIONS IMPORTANTES POUR LUTILISATION
SCURITAIRE DE VOTRE ORDINATEUR OU POUR LINTGRIT DE VOS FICHIERS. VEUILLEZ LIRE
ATTENTIVEMENT TOUTES LES MISES EN GARDE.
LICNE DAVERTISSEMENT MET EN VIDENCE DES INFORMATIONS SUR DES DANGERS POUR VOUS, VOTRE
LIFEBOOK OU VOS FICHIERS. VEUILLEZ LIRE ATTENTIVEMENT TOUS LES AVERTISSEMENTS.
ORDINATEUR
Plusieurs faons soffrent vous pour contacter lquipe de service et assistance de Fujitsu :
Appel sans frais : 1-800-8Fujitsu (1-800-838-5487)
Site Internet : http://www.computers.us.fujitsu.com/support
Avant de nous contacter, veuillez avoir les informations suivantes porte de main pour que notre prpos
du service la clientle puisse vous venir en aide le plus rapidement possible :
Nom du produit
Numro de configuration du produit
Numro de srie du produit
Date dachat
8 - propos de ce guide
POUR UTILISER LES HYPERLIENS, VOUS DEVEZ AVOIR UNE CONNEXION INTERNET ACTIVE.
Garantie limite
Votre ordinateur portable LIFEBOOK est accompagn dune garantie limite internationale de Fujitsu.
Pour connatre les conditions gnrales et la dure de votre garantie limite, consultez la pochette de
service livre avec votre ordinateur.
9 - propos de ce guide
Chapitre 1
10
Camra Web
cran
Haut-parleur stro
Tableau de voyants dtat
Bouton dalimentation/
veille/reprise
Tableau de
voyants dtat
Haut-parleur stro
Prise dcouteurs
Prise de micro
Fente pour cartes MS/SD
Commutateur
de dispositif Pav tactile
sans fil
Touchpad
Composants suprieurs
Voici une courte description des composants se trouvant sur le dessus de votre ordinateur LIFEBOOK.
Camra Web
La camra web de 1,3 mgapixels vous permet de transmettre sur Internet des images de vous-mme.
Pour de plus amples informations concernant lutilisation du microphone et de la camra web, consultez
la documentation accompagnant lapplication CyberLink YouCam.
11 - Emplacement des commandes et des connecteurs
cran
Lordinateur est quip dun cran cristaux liquides couleur avec rtro-clairage, permettant dafficher
des textes et des images.
Tableau de voyants dtat
Les tableaux de voyants dtat contiennent des symboles correspondant divers composants de votre ordinateur
LIFEBOOK. Voir Tableau de voyants dtat en page 19.
Bouton dalimentation/veille/reprise
Le bouton dalimentation/veille/reprise vous permet de mettre votre ordinateur en veille sans lteindre,
de reprendre lutilisation de lordinateur lorsquil a t mis en veille et de le faire dmarrer sil est teint.
Voir Bouton dalimentation/veille/reprise en page 41.
Haut-parleurs stro
Clavier complet avec plusieurs touches spciales Windows. Voir Clavier en page 22.
Pav tactile TouchPad
Le dispositif de pointage Touchpad fonctionne comme une souris, il comprend un bouton droit, un bouton
gauche, ainsi quun pav de commande de curseur. Voir Dispositif de pointage TouchPad en page 25.
Commutateur Marche/Arrt du dispositif sans fil
Ce commutateur permet dactiver/dsactiver les dispositifs sans fil en option tels que WLAN et Bluetooth.
Pour prolonger la longvit de la batterie, teignez ces priphriques entre les utilisations. Voir
Activation de la carte rseau sans fil en page 134.
Fente mixte pour cartes Memory Stick/Secure Digital (MS/SD)
La fente pour cartes Memory Stick/Secure Digital (MS/SD) permet dintroduire une carte mmoire pour
la conservation des donnes. Ce support vous permet de transfrer des donnes partir dune grande varit
de priphriques numriques. Voir Cartes Secure Digital en page 57.
La prise micro/entre de ligne vous permet de connecter un microphone stro externe. Voir Prise
micro/entre de ligne en page 64.
Prise couteurs/sortie
Cette prise permet de connecter des couteurs ou des haut-parleurs externes. Voir Prise
dcouteurs/sortie de ligne en page 64.
Microphone numrique
Le microphone numrique en option est utilis en association avec la camra web. Pour de plus amples
informations concernant lutilisation du microphone et de la camra web, consultez la documentation
accompagnant lapplication CyberLink YouCam.
La prise dalimentation c.c. sert brancher ladaptateur secteur, lequel permet dalimenter lordinateur
LIFEBOOK et de charger la batterie interne au lithium.
Grilles de ventilation
Les grilles permettent lair de circuler dans le systme afin de refroidir les composants.
POUR PROTGER VOTRE ORDINATEUR DES DOMMAGES ET OPTIMISER SES PERFORMANCES, GARDEZ
TOUJOURS LES GRILLES DE VENTILATION DGAGES, PROPRES ET SANS DBRIS. IL EST POSSIBLE
QUE VOUS DEVIEZ LES NETTOYER PRIODIQUEMENT, SELON LENVIRONNEMENT DANS LEQUEL VOUS
UTILISEZ LORDINATEUR.
NE PLACEZ PAS LORDINATEUR DANS UN ENDROIT O LES GRILLES DE VENTILATION POURRAIENT TRE
OBSTRUES, NOTAMMENT DANS UN PETIT ESPACE FERM OU SUR UNE SURFACE MOLLE COMME UN LIT
OU UN COUSSIN.
Le port vido externe permet de connecter un moniteur externe ou un projecteur ACL. Voir Port vido
externe en page 67.
Port HDMI
Le port HDMI est conu pour tre utilis avec des priphriques numriques compatibles avec votre
ordinateur, tels quune tlvision haute dfinition ou un rcepteur AV (audio-vido).
Ports USB 2.0
Les ports USB 2.0 vous permettent de connecter des priphriques USB. La norme USB 2.0 transfre des
donnes un dbit thorique de 480 Mbit/s. Elle est rtrocompatible avec les priphriques USB 1.1 dont
le dbit atteint 12 Mbit/s. Voir Prise dcouteurs/sortie de ligne en page 64. Remarque : les deux ports
USB 2.0 situs sur les cts gauche et droit de lordinateur proposent une capacit de charge USB en tout
temps, laquelle permet de charger un priphrique USB, que lordinateur soit allum ou non.
Lecteur optique
Lecteur optique
Bouton douverture
Prise de rseau
local (RJ-45)
Fente pour
Ports USB 2.0
dispositif antivol
Le compartiment de lecteur optique contient un graveur de DVD multiformat double couche ou un lecteur
Blu-ray. Voir Lecteur optique en page 50.
Bouton douverture du lecteur optique
Le port USB 2.0 vous permet de connecter des priphriques USB. La norme USB 2.0 transfre des donnes
un dbit thorique de 480 Mbit/s. Elle est rtrocompatible avec les priphriques USB 1.1 dont le dbit
atteint 12 Mbit/s. Voir Prise dcouteurs/sortie de ligne en page 64.
Prise de rseau local (RJ-45)
La prise de rseau local interne (RJ-45) peut tre utilise pour raliser une connexion interne Ethernet
10/100/1000 BaseTx. Voir Prise de rseau local (RJ-45) interne en page 63.
Fente pour dispositif antivol
La fente de dispositif antivol vous permet dinstaller un dispositif antivol disponible en option.
16 - Emplacement des commandes et des connecteurs
Grilles de ventilation
(divers emplacements)
Mmoire
de mmoire
module de mmoire
Votre ordinateur est quip en usine dune mmoire vive synchrone dynamique de type 3 double dbit et
haute vitesse (SDRAM DDR3). Le compartiment de mmoire permet daugmenter la capacit de mmoire
systme de votre ordinateur pour en amliorer les performances globales. Voir Module de mmoire
additionnelle en page 59. Normalement, vous ne devriez pas avoir ouvrir ce compartiment.
17 - Emplacement des commandes et des connecteurs
Les grilles permettent lair de circuler dans le systme afin de refroidir les composants.
POUR PROTGER VOTRE ORDINATEUR DES DOMMAGES ET OPTIMISER SES PERFORMANCES, GARDEZ
TOUJOURS LES GRILLES DE VENTILATION DGAGES, PROPRES ET SANS DBRIS. IL EST POSSIBLE
QUE VOUS DEVIEZ LES NETTOYER PRIODIQUEMENT, SELON LENVIRONNEMENT DANS LEQUEL VOUS
UTILISEZ LORDINATEUR.
NE PLACEZ PAS LORDINATEUR DANS UN ENDROIT O LES GRILLES DE VENTILATION POURRAIENT TRE
OBSTRUES, NOTAMMENT DANS UN PETIT ESPACE FERM OU SUR UNE SURFACE MOLLE COMME UN LIT
OU UN COUSSIN.
Verr num
Verr maj
Verr dfil
Bleu clignotant : Ladaptateur secteur et la batterie sont disponibles et le systme est en mode sommeil.
teint : Ladaptateur nest pas branch.
Voyant de niveau de charge
Le voyant de niveau de charge de la batterie affiche le niveau de charge de la batterie comme suit :
Avec adaptateur secteur branch
Bleu continu : Ladaptateur secteur est branch et la batterie est charge.
Orange continu : Ladaptateur secteur est branch et la batterie est en cours de charge.
Aucun adaptateur secteur branch
Orange clignotant : Le clignotement indique que la batterie est charge 12 % ou moins.
Violet, clignotant : Problme de batterie.
teint : Ladaptateur secteur nest pas branch et/ou la batterie est charge entre 13 % et 100 %.
Lorsque la batterie est installe et que lordinateur nest pas sous tension, le voyant de charge
de la pile indiquera le niveau de charge pendant cinq secondes aprs le clignotement orange.
Lorsque ladaptateur secteur nest pas branch ou que la batterie nest pas compltement
charge et que lordinateur se trouve en mode veille, le voyant clignote. Il clignote en sallumant
une seconde toutes les six secondes.
Les batteries soumises des chocs, des vibrations ou des tempratures extrmes risquent
de subir des dgts permanents.
Si une batterie est court-circuite, elle est forcment abme et doit tre remplace.
Clavier
Touches de fonction
Touche Dmarrer
Pav numrique
(dlimit par une ligne noire paisse)
Touche Fn
Touche
dapplication
Touches de curseur
Figure 7. Clavier
Utilisation du clavier
Votre ordinateur portable LIFEBOOK comporte un clavier intgr 86 touches, dont des touches
Windows et des touches de fonctions spciales. Cette section dcrit les touches suivantes.
Pav numrique : Votre ordinateur comprend un pav numrique vous permettant de saisir des
nombres, ainsi que deffectuer des oprations mathmatiques et de navigation. Pour basculer entre
la fonction de navigation et la fonction numrique des touches du pav, utilisez la touche [Verr num].
22 - Clavier
Touches de curseur : Votre clavier contient quatre touches flches permettant de dplacer le
curseur ou le point dinsertion vers la droite, vers la gauche, vers le haut ou vers le bas, dans les
fentres, dans les applications et dans les documents.
Touches de fonction : Les touches [F1] [F12] sutilisent avec la touche [Fn] pour excuter des
actions spciales, selon le programme en cours dutilisation.
Touches Windows : Ces touches fonctionnent de concert avec votre systme dexploitation
Windows et produisent le mme rsultat que si vous cliquiez sur le menu Dmarrer lcran
ou avec le bouton droit de votre pointeur.
Pav numrique
La partie droite du clavier fonctionne comme un pav numrique. Pour activer les fonctions du pav
numrique, appuyez sur la touche [Verr. Num]. Les touches du pav numrique vous permettent de saisir
des chiffres de 0 9, dexcuter des additions ( + ), des soustractions ( - ), des multiplications ( * ), ou des
divisions ( / ), et dentrer des dcimales ( , ) laide des touches de fonction dsignes du pav numrique.
Lorsque la fonction [Verr. Num] est dsactive, vous pouvez vous servir du pav numrique pour naviguer
(Dbut, Insertion, gauche, droite, vers le haut, vers le bas).
Touches Windows
Votre ordinateur portable LIFEBOOK comporte deux touches Windows, soit une touche [Dmarrer] et
une touche [Application]. La touche [Dmarrer] affiche le menu Dmarrer. Ce bouton fonctionne un peu
comme le bouton du menu Dmarrer sur votre cran. La touche [Application] fonctionne comme le bouton
droit de votre souris et affiche un menu de raccourcis sappliquant llment slectionn (pour de plus
amples informations concernant les touches Windows, veuillez consulter votre documentation Windows).
Touches de curseur
Les touches de curseur sont les quatre touches flches qui permettent de dplacer le curseur vers le haut,
vers le bas, vers la gauche et vers la droite dans les applications. Dans les programmes tels que lExplorateur
Windows, elles servent dplacer la mise en vidence (slectionne llment suivant en haut, en bas,
gauche ou droite).
23 - Clavier
Touches de fonction
Votre ordinateur LIFEBOOK comporte 12 touches de fonction, [F1] [F12]. Les fonctions affectes ces
touches varient selon lapplication. Pour les connatre, consultez la documentation du logiciel utilis.
La touche [Fn] permet daccder des fonctions supplmentaires de votre ordinateur portable.
Elle est toujours utilise conjointement avec une autre touche.
[Fn+F3] : Maintenez [Fn] enfonce et appuyez sur [F3] pour activer ou dsactiver la fonction Silence.
[Fn+F4] : Maintenez [Fn] enfonce et appuyez sur [F4] pour activer ou dsactiver le pav tactile
Touchpad. Veuillez prendre note que la combinaison de touches [Fn+F4] fonctionne uniquement
lorsque le paramtre Manual Setting (Configuration manuelle) est slectionn dans le BIOS. (Voir
Utilitaire de configuration du BIOS on page 38.)
[Fn+F6] : Gardez la touche [Fn] enfonce et appuyez plusieurs fois sur [F6] pour diminuer la
luminosit de lcran.
[Fn+F7] : Gardez la touche [Fn] enfonce et appuyez plusieurs fois sur [F7] pour augmenter la
luminosit de lcran.
[Fn+F8] : Gardez la touche [Fn] enfonce et appuyez plusieurs fois sur [F8] pour diminuer le
volume de lordinateur.
[Fn+F9] : Gardez la touche [Fn] enfonce et appuyez plusieurs fois sur [F9] pour augmenter le volume.
[Fn+F10] : Lorsque vous appuyez sur les touches [Fn] + [F10], vous pouvez changer
lemplacement de laffichage vido. chaque combinaison de touches, vous passerez au choix
suivant : Si vous avez un cran tube cathodique externe, lordre est le suivant : cran interne->
cran cathodique externe -> affichage simultan > cran interne.
[Fn+F11] : Maintenez [Fn] enfonce et appuyez sur [F11] pour activer ou dsactiver le mode ECO.
Le mode ECO est conu pour rduire au minimum la consommation de votre ordinateur : la
luminosit de lcran est diminue, le lecteur optique et le lecteur de carte ExpressCard sont teints,
et le mode de mise hors tension automatique du disque dur est activ.
24 - Clavier
Bouton gauche
Bouton droit
Commande du curseur
Votre ordinateur portable LIFEBOOK possde un pav tactile Touchpad intgr. Ce dispositif permet de
commander le dplacement du pointeur et de slectionner des lments affichs lcran. Le pav tactile
Touchpad est compos dune commande de curseur, dun bouton gauche et dun bouton droit. La
commande de curseur fonctionne de la mme faon quune souris, pour faire dplacer le curseur lcran.
Elle fonctionne avec une lgre pression du bout du doigt. Les boutons gauche/droit fonctionnent comme
les boutons dune souris. La fonction exacte des boutons peut varier selon lapplication utilise.
UNE SOURIS EXTERNE PEUT TRE BRANCHE UN PORT USB DE LORDINATEUR PORTABLE
LIFEBOOK ET TRE UTILISE EN MME TEMPS QUE LE PAV TACTILE TOUCHPAD. CEPENDANT, SI
VOUS DMARREZ VOTRE ORDINATEUR AVEC UNE SOURIS EXTERNE DJ CONNECTE, LE PAV TACTILE
TOUCHPAD SERA PAR DFAUT ACTIV OU DSACTIV SELON LES PARAMTRES DE VOTRE BIOS. Voir
Utilitaire de configuration du BIOS on page 38.
Cliquer
Cliquer signifie enfoncer et relcher un bouton. Pour
cliquer gauche, placez le curseur sur llment que
vous dsirez slectionner, puis enfoncez et relchez
immdiatement le bouton gauche. Pour cliquer
droite, placez le curseur sur llment que vous dsirez
slectionner, puis enfoncez et relchez immdiatement
le bouton droit. Vous pouvez galement cliquer en
frappant une fois le pav tactile avec dlicatesse.
Figure 9. Cliquer laide du bouton
Double-cliquer
Double-cliquer signifie cliquer rapidement, deux fois
de suite, avec le bouton gauche. Cette procdure ne
fonctionne pas avec le bouton droit. Pour effectuer
un double-clic, placez le pointeur sur lobjet voulu
et appuyez rapidement deux fois sur le bouton gauche.
Vous pouvez galement effectuer un double-clic en
tapant deux fois lgrement sur le Touchpad.
Figure 11. Double-cliquer laide
du bouton
Glisser
Glisser signifie enfoncer le bouton gauche, sans le
relcher, en dplaant le curseur. Pour faire glisser
un lment, placez dabord le curseur sur cet lment.
Ensuite, enfoncez et tenez le bouton gauche tout en
dplaant llment son nouvel emplacement, puis
relchez. Vous pouvez galement glisser un lment
avec le pav tactile Touchpad. Premirement, placez
le curseur sur llment que vous dsirez dplacer et
frappez lgrement le pav tactile Touchpad deux
reprises en faisant attention de laisser le doigt sur le
pav aprs la dernire frappe. Ensuite, glissez votre
doigt sur le pav tactile jusqu ce que llment soit
lemplacement dsir et retirez votre doigt.
Pour activer ou dsactiver les fonctions gestuelles, allez Dmarrer > Panneau de configuration >
Priphriques (ou Matriel ou quipement) et Sons.
2
3
1
2
Rglage du volume
Votre ordinateur LIFEBOOK Fujitsu est dot de plusieurs commandes de volume fonctionnant en interaction.
LES APPLICATIONS POUVANT REPRODUIRE DES FICHIERS AUDIO PROPOSENT GALEMENT LEUR
PROPRE COMMANDE DE VOLUME (COMMANDE LOGICIELLE). SI VOUS INSTALLEZ UN PRIPHRIQUE
AUDIO EXTERNE DOT DUNE COMMANDE DE VOLUME INDPENDANTE, LA COMMANDE DE VOLUME
DE LAPPAREIL ET LA COMMANDE DE VOLUME LOGICIELLE FONCTIONNERONT EN INTERACTION. VOUS
DEVEZ TOUTEFOIS SAVOIR QUE SI VOUS COUPEZ LE VOLUME AVEC LA COMMANDE LOGICIELLE, LA
COMMANDE DE VOLUME EXTERNE SERA GALEMENT DSACTIVE.
Rglage du volume
Le volume peut tre rgl de plusieurs manires :
Vous pouvez aussi ajuster et couper/remettre le volume avec licne de volume dans la zone
de notification.
Le volume peut galement tre rgl avec les touches de fonction [F8] et [F9]. Gardez la touche [Fn]
enfonce et appuyez plusieurs fois sur [F8] pour rduire le volume sonore de lordinateur. Gardez la
touche [Fn] enfonce et appuyez plusieurs fois sur [F9] pour augmenter le volume sonore de lordinateur.
Si vous dsirez modifier le volume, ouvrez de panneau de configuration, slectionnez une taille
dicne dans le champ Affichage par : , puis slectionnez le Centre de mobilit Windows.
Ensuite, dans la zone Volume , vous pourrez rgler le volume ou passer en sourdine.
Gardez la touche [Fn] enfonce et appuyez sur la touche [F3] pour couper le son. Pour rtablir
le son, appuyez de nouveau sur [Fn+F3].
Le volume peut aussi tre rgl avec les commandes de volume proposes par diverses applications.
Certains priphriques audio pouvant tre connects votre systme sont dots de commandes de volume.
Chaque commande de volume ci-dessus impose une limite suprieure sappliquant aux autres commandes.
Nous vous recommandons dessayer les diffrentes commandes pour dcouvrir le rglage vous convenant
le mieux.
31 - Rglage du volume
Chapitre 2
Adaptateur secteur
Prise c.c.
Cble secteur
Sources dalimentation
Votre ordinateur portable LIFEBOOK Fujitsu peut utiliser trois sources dalimentation diffrentes :
une batterie au lithium principale, un adaptateur secteur et un adaptateur auto/avion.
Connexion des adaptateurs dalimentation
Ladaptateur secteur et ladaptateur auto/avion disponible en option permettent tous deux de faire
fonctionner votre ordinateur portable et de charger les batteries.
Connexion de ladaptateur secteur
1 Branchez le cble de sortie c.c. dans la prise dalimentation c.c. de votre ordinateur LIFEBOOK.
2 Branchez ladaptateur secteur sur une prise lectrique secteur (c.a.).
Connexion de ladaptateur auto/avion disponible en option
1 Branchez le cble de sortie c.c. sur la prise dalimentation c.c. de votre ordinateur portable.
2 Branchez ladaptateur auto/avion sur une prise dallume-cigarette dun vhicule automobile et placez le contact
dallumage sur la position Marche ou Accessoires,
OU
Branchez ladaptateur auto/avion sur la prise dalimentation c.c. de votre sige davion.
Passer dune alimentation sur adaptateur secteur ou auto/avion une alimentation sur batterie
1
2
Assurez-vous quau moins une batterie charge est installe dans votre ordinateur.
Dbranchez ladaptateur secteur ou ladaptateur auto/avion.
LORSQUE VOUS RECEVEZ VOTRE NOUVEL ORDINATEUR, LA BATTERIE AU LITHIUM NEST PAS CHARGE.
LORS DE LA PREMIRE UTILISATION DE VOTRE ORDINATEUR, VOUS DEVEZ CONNECTER LADAPTATEUR
SECTEUR OU LADAPTATEUR AUTO/AVION.
33 - Sources dalimentation
cran
Votre ordinateur portable LIFEBOOK Fujitsu comporte un cran rtro-clairage permettant une lecture
facile dans les environnements forte luminosit. Cet cran offre galement une excellente rsolution
grce une technologie de matrice active.
Ouverture de lcran
Pour ouvrir lcran, tenez la base de lordinateur dune main et inclinez lgrement lcran de lautre,
jusqu obtenir une position confortable, tout en faisant attention de ne pas toucher la surface
daffichage.
34 - cran
LORSQUE VOUS EMPLOYEZ UNE ALIMENTATION SECTEUR, LCRAN UTILISE PAR DFAUT LE NIVEAU DE
LUMINOSIT LE PLUS LEV. LORSQUE VOUS EMPLOYEZ UNE ALIMENTATION SUR BATTERIE, LCRAN
UTILISE PAR DFAUT UN NIVEAU DE LUMINOSIT MOYEN.
PLUS LA LUMINOSIT EST LEVE, PLUS LORDINATEUR CONSOMME DNERGIE ET PLUS LA LONGVIT DE
VOTRE BATTERIE SERA RDUITE. SI VOUS DSIREZ MAXIMISER LA LONGVIT DE LA BATTERIE, RGLEZ LA
LUMINOSIT AU PLUS BAS NIVEAU POSSIBLE.
Fermeture de lcran
Saisissez le bord de votre cran et abaissez-le vers lavant jusqu ce quil soit appuy contre le botier
principal de votre ordinateur LIFEBOOK.
35 - cran
Pour allumer lordinateur LIFEBOOK lorsquil est compltement teint, appuyez sur le bouton
dalimentation/veille/reprise situ en haut droite du clavier. Lorsque vous avez termin de travailler avec
lordinateur, vous pouvez soit le laisser en mode veille (voir Mode sommeil on page 41), soit le mettre
hors tension (voir Mise hors tension on page 44).
LORSQUE LE LIFEBOOK EST ALLUM, NE LE TRANSPORTEZ PAS ET PROTGEZ-LE DES CHOCS ET DES
VIBRATIONS CAR VOUS RISQUERIEZ ALORS DE LENDOMMAGER.
Lorsque vous allumez votre ordinateur LIFEBOOK, ce dernier excute un auto-test de mise sous tension
pour vrifier les composants internes et la configuration. Si une anomalie est dcouverte, votre ordinateur
LIFEBOOK met un avertissement audio et affiche un message derreur. Voir Messages de lautodiagnostic de mise sous tension on page 82. Selon la nature du problme, vous pourrez poursuivre le
dmarrage du systme dexploitation ou vous devrez ouvrir lutilitaire de configuration du BIOS pour
corriger certains paramtres.
Une fois les diagnostics termins, le LIFEBOOK charge le systme dexploitation.
36 - Dmarrage de votre ordinateur portable LIFEBOOK
Procdure damorage
La procdure de dmarrage de lordinateur invoque une procdure damorage, laquelle fait dabord appel
au BIOS. La premire fois que lordinateur LIFEBOOK est allum, la mmoire principale du systme est
vide et doit trouver les instructions de dmarrage de lordinateur. Ces informations se trouvent dans le
programme BIOS. Chaque fois que vous dmarrez ou redmarrez votre ordinateur, il excute une procdure
damorage et lcran affiche le logo Fujitsu jusqu ce que le systme dexploitation soit charg. Cette
procdure comporte diverses oprations dont un auto-test de mise sous tension. Si la procdure damorage
est excute sans chec et sans demande daccs lutilitaire de configuration du BIOS, le message de
bienvenue du systme dexploitation saffiche.
La procdure damorage est excute lorsque :
Vous allumez votre ordinateur portable LIFEBOOK.
Vous redmarrez lordinateur partir de la bote de dialogue Windows darrt du systme.
Un logiciel lance un redmarrage du systme. Exemple : Lorsque vous installez une nouvelle application.
Mots de passe daccs au disque dur
Pour mieux scuriser vos donnes, vous pouvez crer des mots de passe contrlant laccs au(x) disque(s)
dur(s). Cette fonction est gre par lutilitaire de configuration BIOS. Pour savoir comment procder,
reportez-vous la section Utilitaire de configuration du BIOS ci-aprs.
RETENEZ BIEN VOS MOTS DE PASSE. SI VOUS CONFIGUREZ DES MOTS DE PASSE DE MATRE ET
DUTILISATEUR, PUIS QUE VOUS LES OUBLIEZ, FUJITSU AMERICA NE POURRA PAS RINITIALISER
VOTRE SYSTME. VOUS RISQUERIEZ ALORS DE PERDRE DES DONNES ET DE DEVOIR REMPLACER
VOTRE CARTE SYSTME OU VOTRE DISQUE DUR.
Vous pouvez aussi invoquer le menu de la procdure damorage en appuyant sur la touche [F12] lorsque
le logo Fujitsu apparat lcran.
Guide dinformation sur le BIOS
Un guide dinformation sur le BIOS de votre ordinateur portable est disponible en ligne. Pour y accder, veuillez
visiter notre site de service la clientle et dassistance http://www.computers.us.fujitsu.com/support : sous
Online Support (Soutien en ligne), slectionnez Users Guides (Guides dutilisation). Slectionnez votre
produit, sa srie et son modle, puis cliquez sur [Go]. Sous longlet Manuals (Manuels), slectionnez
BIOS Guide (Guide du BIOS).
Dmarrage du systme
Il est fortement recommand de ne pas installer de priphrique externe et de ne pas insrer de DVD/CD
dans votre lecteur avant que la procdure de dmarrage soit entirement termine.
38 - Dmarrage de votre ordinateur portable LIFEBOOK
La premire fois que vous allumez votre ordinateur portable LIFEBOOK, lcran affiche le logo Fujitsu. Si vous
nintervenez pas, lordinateur charge le systme dexploitation et lance la procdure douverture Windows.
Premier dmarrage de Windows
La premire fois que vous faites dmarrer le systme et que vous suivez les instructions lcran, vous
voyez apparatre une fentre de bienvenue. Aprs laffichage de la fentre de bienvenue, lcran se vide
compltement pendant plusieurs minutes. Cela est normal. DURANT CETTE PRIODE, VOUS
NE DEVEZ PAS TENTER DTEINDRE LE SYSTME. Pendant que lcran est vide, le systme
se configure et plusieurs fichiers importants sont installs.
Lors du premier dmarrage, vous devrez lire et accepter les contrats de licence dutilisation de Microsoft
et Fujitsu.
SI VOUS REFUSEZ DACCEPTER LE CONTRAT DE LICENCE, LE SYSTME VOUS DEMANDE DE REVOIR LE CONTRAT
DE LICENCE ET DY LIRE LES INFORMATIONS TRAITANT DE LA PROCDURE DE RETOUR DE WINDOWS SON
FABRICANT, OU DE SIMPLEMENT TEINDRE LORDINATEUR.
VOUS NE POURREZ LUTILISER QUE SI VOUS ACCEPTEZ LE CONTRAT DE LICENCE. SI VOUS NALLEZ PAS AU
BOUT DE CETTE PROCDURE, VOTRE ORDINATEUR RETOURNE LCRAN DE BIENVENUE WINDOWS, MME
SI VOUS ESSAYEZ DTEINDRE LORDINATEUR ET DE LE REDMARRER.
Plusieurs autres fentres safficheront, vous demandant de saisir un nom et une description pour votre ordinateur,
ainsi quun mot de passe dadministrateur et un nom de domaine. Lisez attentivement les instructions saffichant
lcran et remplissez les espaces mesure que le systme vous le demande. Une fois la configuration initiale
termine, il est trs important que vous installiez ClickMe! conformment la procdure ci-dessous.
Installation de Click Me!
ClickMe!
AVANT DINSTALLER LUTILITAIRE CLICK ME!, ASSUREZ-VOUS DACTIVER LE DISPOSITIF DE RSEAU LOCAL
SANS FIL EN ALLUMANT LE COMMUTATEUR DE DISPOSITIFS SANS FIL SITU LAVANT DE LORDINATEUR.
39 - Dmarrage de votre ordinateur portable LIFEBOOK
La premire fois que le systme dmarre, licne Click Me! apparat dans le menu Dmarrer. Il est
trs important dexcuter ClickMe! au premier dmarrage pour vous assurer que les applications,
utilitaires et pilotes ncessaires soient installs. Lorsque vous cliquez sur licne Click Me!, votre
systme configure automatiquement les icnes appropries dans zone de notification en bas droite de
lcran. Ces icnes offrent des liaisons avec des utilitaires susceptibles dtre utiliss frquemment.
Linstallation de ClickMe! est longue car elle implique linstallation de plusieurs applications et utilitaires.
Il se peut que le systme se mette en mode Veille pendant cette procdure (clignotement du voyant
dalimentation). Si cela se produit, poussez momentanment le bouton alimentation/veille/reprise
pour rveiller le systme. En outre, durant lexcution de ClickMe!, vous pouvez glisser votre doigt sur
le pav tactile intervalles de quelques minutes pour garder le systme veill.
IL EXISTE PEUT-TRE DES APPLICATIONS TIERS QUI NE SONT PAS INSTALLES PAR LUTILITAIRE CLICK
ME! POUR PLUS DINFORMATIONS, REPORTEZ-VOUS AU GUIDE DINTRODUCTION.
Pour enregistrer votre ordinateur LIFEBOOK, vous pouvez aller sur notre site Internet :
us.fujitsu.com/computers. Pour vous enregistrer en ligne, vous devez avoir un compte valide
auprs dun fournisseur daccs Internet.
Utilitaire de mise jour des pilotes Fujitsu Driver Update
Votre systme dispose dun outil pratique appel Utilitaire de Mise jour des pilotes Fujitsu (FDU
ou Fujitsu Driver Update). Avec FDU, vous pouvez choisir daller automatiquement ou manuellement
sur le site de Fujitsu pour obtenir les mises jour rcentes de votre systme. Pour obtenir davantage
de renseignements concernant lutilitaire FDU, reportez-vous Tlchargement automatique des mises
jour de pilotes on page 93.
40 - Dmarrage de votre ordinateur portable LIFEBOOK
Gestion de lalimentation
Votre portable LIFEBOOK possde plusieurs dispositifs permettant dconomiser lnergie de la batterie.
Certains dentre eux sont automatiques et ne ncessitent donc aucune intervention. Cependant, dautres
dpendent de paramtres que vous pouvez configurer en fonction de vos conditions dutilisation, notamment
en ce qui concerne la luminosit de lcran. Les paramtres de gestion interne de lalimentation peuvent
tre configurs dans votre systme dexploitation, dans une application intgre de gestion de lalimentation
ou dans lutilitaire de configuration du BIOS.
Outre les dispositifs prcdents de conservation de lnergie de la batterie, dautres moyens sont votre
disposition pour viter lpuisement trop rapide de votre batterie. Par exemple, vous pouvez crer un profil
de gestion de lalimentation, vous pouvez mettre votre ordinateur en mode sommeil lorsquil nexcute
aucune opration ou vous pouvez limiter lutilisation des priphriques consommant le plus dnergie.
linstar de tous les ordinateurs portables aliments par batterie, vous devez trouver le meilleur compromis
entre performance et rendement nergtique.
Bouton dalimentation/veille/reprise
Lorsque lordinateur est allum, vous pouvez utiliser le bouton dalimentation/veille/reprise pour placer
manuellement lordinateur en mode sommeil. Assurez-vous alors que lordinateur nest pas en train daccder
des donnes, puis enfoncez et relchez immdiatement le bouton dalimentation/veille/reprise. Veuillez
prendre note que si vous enfoncez ce bouton pendant au moins 4 secondes, votre ordinateur steindra et
les donnes actives ce moment-l risque dtre perdues.
Pour rveiller lordinateur lorsquil est en mode veille, appuyez de nouveau sur le bouton dalimentation/
veille/reprise. Pour savoir si lordinateur est en mode veille, regardez le voyant lumineux dalimentation.
Si le voyant est allum sans clignoter, lordinateur est entirement fonctionnel. Si le voyant est allum et
quil clignote, lordinateur est en mode sommeil. Si le voyant est teint, lordinateur est teint ou en veille
prolonge (voir la rubrique traitant du mode Veille prolonge).
Mode sommeil
Lorsque le mode sommeil est activ, Windows conserve le contenu de votre mmoire de systme durant
la priode dinactivit en maintenant lalimentation de certains composants critiques. Ce mode teint lunit
centrale, lcran, le disque dur et tous les autres composants internes sauf ceux qui sont ncessaires pour
conserver la mmoire du systme et permettre son redmarrage.
41 - Gestion de lalimentation
Votre ordinateur entrera en mode Veille dans les situations ou suite aux actions suivantes :
En appuyant sur le bouton dalimentation/veille/reprise (si lordinateur est allum).
En slectionnant le mode sommeil partir du menu Arrt de Windows.
Lorsque le dlai dinactivit est atteint.
En laissant la charge de la batterie descendre au niveau Avertissement de batterie faible.
Dans ces situations, la mmoire de systme de lordinateur enregistre gnralement le fichier sur lequel
vous travaillez, des informations sur les applications ouvertes et dautres donnes ncessaires aux oprations
en cours. Lorsque vous quittez le mode sommeil, lordinateur retournera ltat o vous lavez laiss.
Pour reprendre lutilisation de lordinateur, vous devez employer le bouton dalimentation/veille/reprise
et vous devez disposer dune source dalimentation valide.
n
SI LORDINATEUR UTILISE LALIMENTATION PAR BATTERIE, NOUBLIEZ PAS QUE LA BATTERIE CONTINUE SE
DCHARGER MME EN MODE SOMMEIL, MAIS PLUS LENTEMENT QUEN MODE DE FONCTIONNEMENT NORMAL.
SI VOTRE ORDINATEUR ACCDE ACTIVEMENT DES INFORMATIONS AU MOMENT O VOUS LE METTEZ EN MODE
SOMMEIL OU EN MODE VEILLE PROLONGE, LES MODIFICATIONS AUX FICHIERS OUVERTS NE SERONT PAS PERDUES.
LORSQUE VOUS ACTIVEZ LE MODE SOMMEIL, LES FICHIERS SONT LAISSS OUVERTS ET LA MMOIRE DEMEURE ACTIVE.
SI VOUS CHOISISSEZ LE MODE VEILLE PROLONGE, LA MMOIRE EST TRANSFRE SUR LE DISQUE DUR INTERNE.
LE PRINCIPAL AVANTAGE DU MODE VEILLE PROLONGE EST QUAUCUNE NERGIE NEST NCESSAIRE POUR CONSERVER
VOS DONNES. CET AVANTAGE EST PARTICULIREMENT IMPORTANT SI VOUS COMPTEZ LAISSER VOTRE ORDINATEUR
EN VEILLE PENDANT DE LONGUES PRIODES. LES PRINCIPAUX INCONVNIENTS DE LA VEILLE PROLONGE SONT
UNE PLUS LONGUE DURE DES PROCDURES DE MISE EN VEILLE ET DE REPRISE, AINSI QUE LA RINITIALISATION
DES PRIPHRIQUES.
Dans la configuration par dfaut, cette fonction est active. Pour activer ou dsactiver la fonction de veille
prolonge, excutez les oprations suivantes :
1
2
Cliquez sur le bouton [Dmarrer], puis positionnez le curseur sur la petite flche situe en bas droite du panneau
de droite.
43 - Gestion de lalimentation
Si vous arrtez votre systme depuis Windows, vous permettez lordinateur de terminer les oprations
en cours, vous lui permettez aussi dexcuter les oprations de mise hors tension dans le bon ordre et vous
vitez les risques derreur. La procdure approprie est la suivante :
Cliquez sur le bouton [Dmarrer], puis positionnez le curseur sur la petite flche situe en bas droite du
panneau de droite. Cliquez sur le bouton [Arrter].
44 - Gestion de lalimentation
Chapitre 3
45
LAUTONOMIE RELLE DE LA BATTERIE PEUT VARIER SELON LA LUMINOSIT DE LCRAN, SELON LES
APPLICATIONS, LES FONCTIONS ET LES PARAMTRES DE GESTION DE LALIMENTATION QUE VOUS
UTILISEZ, SELON LTAT DE LA BATTERIE ET SELON DAUTRES PRFRENCES QUE VOUS POUVEZ
CONFIGURER.
DISQUE DUR PEUT GALEMENT AVOIR UN IMPACT SIGNIFICATIF SUR LA DURE DE VIE DE LA BATTERIE.
IL EST POSSIBLE QUE DES LOIS FDRALES, PROVINCIALES OU LOCALES INTERDISENT DE JETER DES
BATTERIES DANS LES DCHETS DOMESTIQUES. CONTRIBUEZ LA PROTECTION DE LENVIRONNEMENT ET
JETEZ VOS BATTERIES USES CONFORMMENT AUX LOIS EN VIGUEUR. POUR OBTENIR DES INFORMATIONS
SUR LE RECYCLAGE ET LA MISE AUX REBUTS DES VIEILLES BATTERIES, CONSULTEZ LES AUTORITS
LOCALES OU PROVINCIALES COMPTENTES. SI VOUS NARRIVEZ PAS TROUVER CES INFORMATIONS,
CONTACTEZ UN PRPOS DU SERVICE LA CLIENTLE AU
1-800-8FUJITSU (1-800-838-5487).
Puisque les batteries au lithium nont aucun effet de mmoire, il nest pas ncessaire de dcharger
compltement votre batterie avant de la recharger. La dure de charge sera nettement plus longue si vous
utilisez lordinateur pendant que la batterie se charge. Si vous dsirez charger la batterie le plus rapidement
possible, placez votre ordinateur en mode veille ou teignez-le pendant que la batterie se charge (pour de
plus amples informations sur le mode veille et la procdure darrt, reportez-vous Gestion de
lalimentation en page 41).
46 - Batterie au lithium
Batterie faible
Lorsque la batterie est faible, le systme affiche un avis de batterie faible. Si vous ne prtez pas attention
cet avis de batterie faible, la batterie continuera se dcharger jusqu ce quelle ne puisse plus faire
fonctionner le systme. Lorsque cela se produit, lordinateur se place en mode veille. Dans un tel cas, rien
ne garantit que toutes vos donnes seront sauvegardes.
n
LORSQUE LAVIS DE BATTERIE FAIBLE APPARAT, VOUS DEVEZ ENREGISTRER TOUTES VOS DONNES ACTIVES ET
LIFEBOOK EN MODE VEILLE JUSQU CE QUE VOUS PUISSIEZ DISPOSER DUNE
AUTRE SOURCE DALIMENTATION. VOUS DEVEZ CONNECTER LE PLUS RAPIDEMENT POSSIBLE UNE BATTERIE
CHARGE, UN ADAPTATEUR SECTEUR OU UN ADAPTATEUR AUTO/AVION.
PLACER VOTRE ORDINATEUR
LORSQUE LORDINATEUR EST EN MODE VEILLE, IL DOIT TOUJOURS DISPOSER DAU MOINS UNE BONNE SOURCE
SI VOUS RETIREZ TOUTES LES SOURCES DALIMENTATION ALORS QUE LORDINATEUR EST EN
MODE VEILLE, TOUTES LES DONNES NAYANT PAS T SAUVEGARDES SONT PERDUES.
DALIMENTATION.
Lorsque lordinateur est en mode veille de batterie puise, il est impossible den reprendre lutilisation
avant davoir connect une source dalimentation valide provenant dun adaptateur ou dune batterie
charge. Lorsque vous avez connect une alimentation valide, vous devez ensuite appuyer sur le bouton
dalimentation/veille/reprise pour reprendre lutilisation de lordinateur.
Lorsque lordinateur est en mode veille de batterie puise, vos donnes peuvent tre sauvegardes
pendant une certaine priode, mais si vous ne connectez pas rapidement une source dalimentation valide,
le voyant dalimentation cesse de clignoter et steint, provoquant la perte de toutes les donnes nayant
pas t enregistres. Si vous connectez un adaptateur, vous pouvez poursuivre lutilisation de lordinateur
pendant que la batterie se recharge.
Batterie court-circuite
Le voyant de charge de la batterie (dans le tableau de voyants dtat) contient un symbole indiquant le niveau
de charge disponible. Si ce symbole indique que la batterie est court-circuite, cette dernire est endommage
et doit tre remplace pour viter quelle nendommage dautres composants de votre ordinateur.
47 - Batterie au lithium
Remplacement de la batterie
Si vous achetez une batterie supplmentaire de rechange, vous pourrez remplacer la batterie principale si
elle vient se dcharger compltement. Deux mthodes soffrent vous pour remplacer votre batterie : le
remplacement hors tension et le remplacement sous tension.
Remplacement hors tension
Pour remplacer la batterie alors que le systme est hors tension, excutez les oprations suivantes :
1
2
3
4
5
6
Pour remplacer la batterie alors que le systme est sous tension, excutez les oprations suivantes :
AVANT DENLEVER LA BATTERIE, ASSUREZ-VOUS QUE LADAPTATEUR SECTEUR EST BIEN CONNECT.
LORDINATEUR NE DISPOSE DAUCUNE BATTERIE TEMPORAIRE POUR FAIRE FONCTIONNER LE SYSTME
DURANT LE REMPLACEMENT DE LA BATTERIE. SI VOUS NUTILISEZ PAS LADAPTATEUR SECTEUR, VOUS
PERDREZ TOUTES LES DONNES NON ENREGISTRES.
1
2
Branchez ladaptateur secteur sur votre ordinateur, puis sur une prise lectrique sous tension.
Suivez les tapes 3 et 4 de la section Remplacement hors tension .
SI LE CONNECTEUR DE LA BATTERIE AU LITHIUM NEST PAS BIEN ENFONC, VOUS RISQUEZ DE NE PAS
POUVOIR UTILISER LORDINATEUR OU DE NE PAS POUVOIR RECHARGER LA BATTERIE.
48 - Batterie au lithium
Loquet de dgagement
de la batterie
Loquet de dgagement
de la batterie
49 - Batterie au lithium
Lecteur optique
Votre systme est dot dun des lecteurs optiques suivants :
Lecteur ROM Blu-ray : Ce lecteur vous permet de lire des films, des logiciels et des DVD/CD audio,
ainsi que de lire des disques des formats suivants : BD-ROM (couche simple et double couche), BD-R
(couche simple et double couche), BD-RE (couche simple et double couche), DVD-ROM (couche simple
et double couche), DVD+R (couche simple et double couche), DVD-R (couche simple et double couche),
DVD+RW (couche simple) DVD-RW (couche simple), DVD-RAM (Ver.2), CD-ROM, CD-R et CD-RW.
Ce lecteur permet de graver des disques des formats suivants : DVD-RAM (Ver2), DVD+R (couche
simple et double couche), DVD+RW, DVD-R (couche simple et double couche), DVD-RW, CD-R
et CD-RW. Il offre galement toutes les fonctions dun lecteur de CD/DVD/BD-ROM ordinaire.
Graveur de DVD multiformat double couche : Ce lecteur vous permet daccder des films, logiciels
et DVD/CD audio, ainsi que de lire et dcrire sur des disques CD-R, CD-RW, DVD-R, DVD+R, DVDRW, DVD+RW et DVD-RAM. Larchitecture double couche permet denregistrer jusqu 8,5 Go sur les
disques DVD+R.
50 - Lecteur optique
NE FAITES FONCTIONNER VOTRE LECTEUR OPTIQUE QUE SI VOTRE ORDINATEUR PORTABLE LIFEBOOK SE
TROUVE SUR UNE SURFACE PLATE. LUTILISATION DUN LECTEUR LORSQUE LE SYSTME NEST PAS NIVEAU
RISQUE DENDOMMAGER LE LECTEUR OU DEMPCHER SON FONCTIONNEMENT APPROPRI.
UNE UTILISATION PROLONGE DUN LECTEUR OPTIQUE (NOTAMMENT POUR VOIR UN FILM DVD) RDUIRA
CONSIDRABLEMENT LA LONGVIT DE VOTRE BATTERIE, MOINS QUE VOUS NUTILISIEZ UNE SOURCE
DNERGIE EXTERNE.
Appuyez et relchez la touche djection situe lavant du lecteur optique afin douvrir le plateau de
chargement. Le plateau sortira lgrement du portable LIFEBOOK.
Tirez doucement le plateau de chargement jusqu ce quun disque puisse y tre dpos facilement.
TOUS LES LECTEURS DE DVD LIFEBOOK SONT COMPATIBLES AVEC LES TITRES DE DVD DONT LE
1, CORRESPONDANT AU MARCH NORD-AMRICAIN. LE NUMRO DE RGION
DVD QUI AGIT SELON LES
EXIGENCES DE HOLLYWOOD. DIFFRENTS CODES RGIONAUX SONT ENREGISTRS SUR LES TITRES DE
DVD VIDO POUR PUBLICATION DANS DIFFRENTES RGIONS TRAVERS LE MONDE. SI LE CODE
RGIONAL DU LECTEUR DE DVD NE CORRESPOND PAS AUX CODES RGIONAUX DES TITRES, LA
LECTURE EST IMPOSSIBLE.
NUMRO DE RGION EST
51 - Lecteur optique
Placez le disque dans le plateau de chargement, ltiquette vers le haut, avec lorifice au milieu du disque.
Enfoncez le disque dans le cercle surlev situ au centre du plateau.
Fermez le plateau de chargement en le poussant doucement jusqu ce que vous entendiez un clic.
SI VOUS AVEZ DSACTIV LA FONCTION AVIS DINSERTION AUTOMATIQUE, VOUS DEVREZ FAIRE DMARRER
LE LECTEUR SOIT PARTIR DU POSTE DE TRAVAIL SOIT AVEC LEXPLORATEUR WINDOWS, CAR
LORDINATEUR PORTABLE NE RECONNATRA PAS AUTOMATIQUEMENT QUE LE DISQUE A T CHARG.
52 - Lecteur optique
b.
a.
d.
c.
Appuyez et relchez la touche djection situe lavant du lecteur optique. Le lecteur sarrtera et le plateau
sortira lgrement de lordinateur LIFEBOOK.
2
3
4
Insrez le disque dans le lecteur optique de lordinateur. Si la fonction Excution automatique senclenche,
ignorez ltape 2.
Lorsque vous insrerez un film dans le tiroir du lecteur pour la premire fois, on vous invitera choisir ce que
vous aimeriez que le systme fasse lorsque les disques sont insrs (par exemple, dmarrer automatiquement
ou attendre le message-guide). Ce mme message saffichera chaque fois que vous insrerez un disque
jusqu ce que vous fassiez votre slection.
Cliquez sur [OK] pour fermer la bote de dialogue propos du lecteur de DVD , et le film commencera.
54 - Lecteur optique
La plupart des DVD-ROM vous permettent de modifier la faon dont le film est visionn et ce que vous
aimeriez voir. Pour cela, il suffit dutiliser le panneau de configuration du lecteur multimdia et la souris.
1
2
Cliquez droite sur lcran du film pour ouvrir le menu droulant des options.
Pour afficher toutes les commandes disponibles, slectionnez Afficher, puis Lecteur. Vous verrez alors
apparatre le panneau de configuration dans le bas de lcran.
Le logiciel du lecteur multimdia vous permet de visionner un film tout comme le fait un magntoscope
cassettes. Vous pouvez faire une pause, rembobiner, avancer rapidement ou arrter un film tout moment.
1
2
Pour faire avancer le film, cliquez sur le bouton pour avancer jusqu un point spcifique de votre choix
ou cliquez sur le bouton . pour passer aux crdits de fermeture.
Pour faire reculer le film, cliquez sur le bouton pour revenir jusqu un point spcifique de votre choix ou
cliquez sur le bouton pour revenir lcran de bienvenue.
Cliquez sur le bouton situ dans le coin suprieur droit de la barre de titre. Vous voyez apparatre une bote
de dialogue du lecteur multimdia.
Cliquez sur [Oui] pour arrter et quitter le film ou sur [Non] pour fermer la bote de dialogue et retourner au film.
55 - Lecteur optique
LA DURE DUN GRAND NOMBRE DE FILMS EST SUPRIEURE LAUTONOMIE DUNE SEULE BATTERIE.
SI VOUS REGARDEZ UN FILM DVD AVEC UNE ALIMENTATION PAR BATTERIE, VOUS AUREZ PROBABLEMENT
BESOIN DUNE BATTERIE ADDITIONNELLE CHARGE OU DE BRANCHER UN ADAPTATEUR SECTEUR
DURANT LE FILM POUR POUVOIR LE VOIR EN ENTIER.
POSSDEZ PAS UNE BATTERIE SUPPLMENTAIRE, VOUS POUVEZ VOUS EN PROCURER UNE SOIT EN
LIGNE HTTP://WWW.COMPUTERS.US.FUJITSU.COM, SOIT EN APPELANT AU
1-877-372-3473.
Ayez votre disposition une batterie supplmentaire charge fond ou un adaptateur secteur.
Commencez la lecture du film DVD.
Lorsque le voyant de batterie faible sallume, arrtez immdiatement le film et quittez le lecteur multimdia.
SI VOUS NARRTEZ PAS LE LECTEUR MULTIMDIA RAPIDEMENT ET QUE LE PORTABLE LIFEBOOK
TENTE DE SARRTER AUTOMATIQUEMENT (TAT CRITIQUE DE BATTERIE FAIBLE), LE PORTABLE
LIFEBOOK STEINDRA DE FAON INAPPROPRIE. SI CETTE SITUATION SE PRODUIT, VOUS DEVRIEZ
EXCUTER UN REDMARRAGE FROID ET SUIVRE LES INSTRUCTIONS, LE CAS CHANT, QUI VOUS
SONT PRSENTES AVANT QUE LE SYSTME NE REDMARRE.
Mettez votre ordinateur hors tension et remplacez la batterie dcharge par la batterie supplmentaire charge
fond. Si vous ne disposez pas dune batterie supplmentaire, vous pouvez brancher un adaptateur secteur
ds que vous voyez lindicateur de faible batterie.
Pour reprendre lutilisation de lordinateur, appuyez nouveau sur le bouton dalimentation/veille/reprise. Cette
opration nest pas ncessaire si vous avez connect un adaptateur secteur sans utiliser le mode veille.
Redmarrez votre lecteur multimdia et retrouvez lendroit o vous avez laiss le film, puis continuez le regarder.
CERTAINS FILMS PLUS COURTS PEUVENT TRE ENTIREMENT VUS SANS NCESSITER DE BATTERIE
SUPPLMENTAIRE OU LE BRANCHEMENT DUN ADAPTATEUR SECTEUR. TOUTEFOIS, IL EST PRFRABLE
DTRE PRT PUISQUE LA LONGVIT RELLE DE LA BATTERIE PENDANT LE FONCTIONNEMENT DU
LECTEUR OPTIQUE NE PEUT PAS TRE GARANTIE.
56 - Lecteur optique
Carte SD
Le guide dutilisation de la carte mmoire vous indiquera comment linstaller. Certaines cartes pourraient
ncessiter que votre portable soit teint pendant que vous les installez.
Avant dinsrer votre carte, assurez-vous quaucune autre carte nest dj installe dans la fente. Si une carte
sy trouve, reportez-vous la rubrique Retrait dune carte Memory Stick ou SD.
3
4
Enfoncez la carte jusqu ce que vous sentiez un dclic. La carte sjecte ensuite de la fente pour que vous
puissiez la retirer.
LE MODULE DE MMOIRE ADDITIONNELLE PEUT TRE FORTEMENT ENDOMMAG PAR UNE DCHARGE
LECTROSTATIQUE
SUIVANTES
ASSUREZ-VOUS DE NE TOUCHER
LA PEAU
DGAGE UNE SUBSTANCE HUILEUSE QUI POURRAIT CAUSER UN COURT-CIRCUIT AUX COMPOSANTS.
AUCUNE BORNE DE CONNEXION NI AUCUN COMPOSANT INTERNE DE LORDINATEUR.
Coupez le courant de votre ordinateur portable et dbranchez ladaptateur dalimentation (adaptateur secteur
ou adaptateur auto/avion), le cas chant. Retirez la batterie.
Tournez lordinateur portable lenvers et retirez la vis du compartiment du module de mmoire additionnelle
(voir Figure 28). Retirez le couvercle.
59 - Module de mmoire additionnelle
3
4
Insrez le module de mmoire additionnelle en oblique, 45. Poussez fermement le bord du connecteur du
module vers le bas et appuyez sur le connecteur jusqu ce quil se loge sous la cl de serrage. Vous entendrez
un clic lorsque celui-ci sera bien en place.
Clavettes dalignement
Cl de serrage
Cls de serrage
Cl de serrage
Figure 29. Installation du module de mmoire
Si vous dsirez vrifier la capacit de mmoire, cliquez sur [Dmarrer] > Panneau de configuration >
Systme et entretien > Systme. La capacit de mmoire est indique ct de Memory - RAM:
(ou Mmoire - RAM).
Il peut y avoir un cart entre la capacit de mmoire installe et celle qui est affiche. Cette situation peut
dcouler du fait que votre systme est configur avec un contrleur vido Intel Graphics Media Accelerator
intgr qui alloue la mmoire systme de manire dynamique afin dacclrer les performances graphiques.
SI LA MMOIRE TOTALE AFFICHE EST INCORRECTE, VRIFIEZ SI LE MODULE DE MMOIRE
ADDITIONNELLE EST BIEN INSTALL. SI LE MODULE EST BIEN INSTALL MAIS QUE LA CAPACIT NEST
TOUJOURS PAS BIEN RECONNUE, CONSULTEZ LA SECTION DPANNAGE EN PAGE 68.
Ports de priphriques
Votre ordinateur portable Fujitsu LIFEBOOK est quip de plusieurs ports auxquels vous pouvez brancher
des priphriques : lecteurs de disque, claviers, imprimantes, etc.
Prise de rseau local (RJ-45) interne
La prise de rseau local interne (RJ-45) peut tre utilise pour raliser une connexion en rseau local Ethernet
(10/100 Gigabit). Il est possible que vous deviez configurer votre ordinateur portable selon les particularits
de votre rseau (pour de plus amples informations sur la configuration de votre rseau, veuillez consulter
votre administrateur de rseau). Pour brancher le cble de rseau local, excutez ces oprations :
1
63 - Ports de priphriques
Ports USB
Les ports Universal Serial Bus 2.0 (USB) vous permettent de connecter divers priphriques USB tels que
des tablettes de jeu externes, des dispositifs de pointage, des claviers et/ou des haut-parleurs. Votre LIFEBOOK
est dot de quatre ports USB 2.0 : deux sur le ct gauche et deux sur le ct droit. La norme USB 2.0 transfre
des donnes un dbit thorique de 480 Mbit/s. Elle est rtrocompatible avec les priphriques USB 1.1
dont le dbit atteint 12 Mbit/s. Le port USB 2.0 situ sur le ct gauche lavant de lordinateur offre une
capacit de charge USB en tout temps (Anytime USB Charge), ce qui signifie que mme si votre ordinateur
est teint, ce port peut tre utilis pour alimenter des priphriques externes.
64 - Ports de priphriques
.
Pour connecter un
priphrique USB, alignez le
connecteur avec l'ouverture
du port, puis pousser le
connecteur l'intrieur
jusqu' ce qu'il s'y enclenche
correctement.
Ports USB
EN RAISON DES CHANGEMENTS CONTINUS APPORTS LA TECHNOLOGIE ET AUX NORMES USB, IL EST
IMPOSSIBLE DE GARANTIR LA COMPATIBILIT DE TOUS LES DISPOSITIFS ET/OU LECTEURS USB..
65 - Ports de priphriques
66 - Ports de priphriques
LORSQUE VOUS APPUYEZ SUR LES TOUCHES [FN] + [F10], VOUS POUVEZ CHANGER LEMPLACEMENT
DE LAFFICHAGE VIDO. CHAQUE FOIS QUE VOUS APPUYEZ SUR CES TOUCHES, VOUS PASSEZ AU
CHOIX SUIVANT. SI VOUS NAVEZ QUUN CRAN TUBE CATHODIQUE, LORDRE SERA LE SUIVANT :
CRAN INTERNE -> CRAN CATHODIQUE EXTERNE -> AFFICHAGE SIMULTAN > CRAN INTERNE.
67 - Ports de priphriques
Chapitre 4
Assurez-vous que les cartes ventuellement installes sur lordinateur sont bien branches. Vous pouvez
galement enlever la carte de la fente pour vous assurer quelle nest pas la raison de la panne.
Assurez-vous que tous les priphriques connects aux connecteurs externes sont bien branchs. Vous
pouvez galement dconnecter ces priphriques pour vous assurer quils ne sont pas lorigine de la panne.
Allumez votre ordinateur portable. Assurez-vous quil soit rest hors fonction pendant 10 secondes au moins
avant de le remettre en marche.
Assurez-vous que ladaptateur secteur est connect votre ordinateur portable et une source dalimentation
secteur active.
68
6
7
SI VOUS PRENEZ EN NOTE TOUT CE QUE VOUS ESSAYEZ, LE SERVICE DASSISTANCE POURRA VOUS
AIDER PLUS RAPIDEMENT EN VOUS DONNANT DES SUGGESTIONS SUPPLMENTAIRES AU TLPHONE.
Si vous avez essay les solutions suggres par le tableau de dpannage sans succs, communiquez avec le
service dassistance :
69 - Dpannage
Problmes spcifiques
Utilisation du tableau de dpannage
Lorsque vous prouvez des problmes avec votre ordinateur portable LIFEBOOK, essayez de trouver les
symptmes sous la colonne Problme du tableau suivant pour la fonction qui vous cause des problmes.
Vous trouverez une description des causes communes pour ce symptme sous la colonne Cause possible ;
le cas chant, ce que vous pouvez faire pour corriger la situation se trouve sous la colonne Solutions
possibles. Il est possible que certaines causes et solutions possibles ne sappliquent pas votre ordinateur.
Tableau de dpannage
Problme
Page
Problme
Page
Problmes dalimentation
lectrique . . . . . . . . . . . . . . . . . . . page 74
Problmes darrt et de
dmarrage . . . . . . . . . . . . . . . . . . page 77
70 - Dpannage
Problme
Cause possible
Solutions possibles
Le volume logiciel
est rgl un niveau
trop bas.
Problmes audio
Aucun son ne sort des hautparleurs incorpors.
71 - Dpannage
Problme
Cause possible
Solutions possibles
Lordinateur portable
LIFEBOOK ne reconnat
pas les DVD/CD-RW/
CD-ROM.
(suite)
Le tiroir du lecteur
optique nest pas
bien ferm.
Le DVD/CD-RW/
CD-ROM est sale
ou dfectueux.
Un mauvais
identificateur dunit a
t utilis pour le disque.
La fonction dinsertion
automatique Windows
est active et vrifie si un
disque est prt tre lu.
Un mauvais identificateur
dunit a t utilis par
une application lorsquun
disque damorage a t
utilis pour dmarrer
votre ordinateur.
Le voyant daccs au
disque situ sur le Tableau
de voyants dtat clignote
intervalles rgulier sans
quun disque nait t insr.
72 - Dpannage
Problme
Cause possible
Solutions possibles
Les paramtres de
scurit exigent un
mot de passe pour le
dmarrage du systme
dexploitation.
Votre application a
verrouill votre clavier.
Le logiciel de votre
systme dexploitation
nest pas configur avec
le bon pilote pour ce
priphrique.
Votre priphrique
externe nest pas
bien install.
Le logiciel de votre
systme dexploitation
nest pas configur
avec le bon pilote pour
ce priphrique.
73 - Dpannage
Problme
Cause possible
Solutions possibles
Votre module de
mmoire additionnelle
nest pas bien install.
Problmes de mmoire
Lcran Proprits du
systme nindique pas la
quantit de mmoire
installe correctement.
Le pilote ne correspond
pas votre priphrique.
Ladaptateur de courant
(secteur ou auto/avion)
est dfectueux.
74 - Dpannage
Problme
Cause possible
Solutions possibles
La batterie installe
est compltement
dcharge ou aucun
adaptateur de courant
nest install.
Ladaptateur secteur
ou auto/avion est mal
branch.
Ladaptateur de courant
ne reoit pas dnergie
de la prise secteur, de
la prise de sige davion
ou de lallume-cigare
de voiture.
Les paramtres de
gestion dalimentation
sont rgls des
temporisations (dlais
dinactivit) automatiques
trop courtes par
rapport vos besoins
dexploitation.
75 - Dpannage
Problme
Cause possible
Solutions possibles
Ladaptateur
dalimentation est tomb
en panne ou a perdu sa
source dnergie.
Lordinateur est
aliment par batterie et
vous navez pas tenu
compte dun
avertissement de
batterie faible ;
lordinateur est donc
maintenant en mode
veille car batterie
puise .
Le LIFEBOOK ne
fonctionne pas lorsquil est
aliment uniquement par
batterie.
76 - Dpannage
Problme
Cause possible
Solutions possibles
La batterie semble se
dcharger trs vite.
Les fonctions
dconomies
dnergie sont peuttre dsactives.
Remplacez la batterie.
Remplacez la batterie.
Le bouton veille/reprise
est dsactiv.
77 - Dpannage
Problme
Cause possible
Solutions possibles
Le systme se met en
marche et affiche les
informations sur la mise en
marche, mais nest pas en
mesure de charger le
systme dexploitation.
Les paramtres
damorage de lutilitaire
de configuration du
BIOS sont incompatibles
avec votre configuration.
Lauto-diagnostic de
mise sous tension
(POST) a dtect
un problme.
La batterie de rtention
du BIOS CMOS fait
dfaut.
Les modifications
que vous avez
apportes la
configuration du BIOS
ntaient pas t
sauvegardes lorsque
vous avez quitt
lutilitaire.
Un message derreur
saffiche durant la
procdure damorage
de lordinateur.
78 - Dpannage
Problme
Cause possible
Solutions possibles
Langle de laffichage
et les paramtres de
luminosit ne sont pas
adapts vos
conditions dclairage.
Les temporisations de
gestion de lalimentation
peuvent tre rgles
des intervalles trop
courts et vous navez
pas remarqu que
lcran sest allum,
puis teint de nouveau.
Lauto-diagnostic de
dmarrage (POST) a
dtect une dfaillance
qui ne permet pas
lcran de fonctionner.
Lordinateur portable
sest retrouv en
temporisation vido, en
mode veille ou en mode
veille prolonge car
vous ne lavez pas
utilis pendant un
certain moment.
Problmes vido
Lcran daffichage intgr
demeure vide lorsque vous
mettez en marche votre
ordinateur LIFEBOOK.
79 - Dpannage
Problme
Cause possible
Solutions possibles
Les temporisations de
gestion de lalimentation
peuvent tre rgles
des intervalles trop
courts et vous navez
pas remarqu que
lcran sest allum,
puis teint de nouveau.
Lcran daffichage ne se
ferme pas.
Ne faites rien.
Lcran dapplication
nutilise quune partie de
la surface daffichage et est
entour dun cadre fonc.
80 - Dpannage
Problme
Cause possible
Solutions possibles
Appuyez sur [Fn] + [F7] pour augmenter la luminosit ou doublecliquez sur lindicateur de batterie pour ajuster le Rglage de
lalimentation dans les Paramtres de la batterie.
Le systme
dexploitation nutilise
pas le bon pilote.
Problmes de connectivit
Vous essayez de vous
connecter Internet mais
le dispositif de rseau local
sans fil semble ne pas tre
aliment.
Les fonctions du
dispositif sans fil
ont t teintes.
Pour activer le dispositif de rseau local sans fil, appuyez sur les
touches [Fn] et [F5] en mme temps. Une fois le dispositif activ,
le voyant correspondant dans le tableau de voyants dtat
sallumera. Pour teindre le dispositif, rptez la mme tape.
Les applications
gnrent souvent leurs
propres messages
derreur.
Problmes divers
Un message derreur
saffiche sur lcran durant
lexcution dune application.
81 - Dpannage
Problme daccs la mmoire NVRAM. Au cas o ce message safficherait, ce qui est peu probable,
vous pourriez avoir un problme daffichage. Vous pouvez continuer utiliser votre ordinateur mais vous
devriez communiquer avec le service dassistance pour plus dinformations.
*Erreur du contrleur de clavier
Le test du contrleur de clavier a chou. Vous pourriez avoir besoin de remplacer votre clavier ou le
contrleur de votre clavier mais vous pourriez utiliser un clavier externe en attendant. Communiquez
avec le service dassistance.
*Le clavier na pas t dtect
Le clavier ne fonctionne pas. Vous pourriez avoir besoin de remplacer votre clavier ou le contrleur de
votre clavier mais vous pourriez utiliser un clavier externe en attendant. Communiquez avec le service
dassistance.
*Systme dexploitation introuvable
Le systme dexploitation ne peut pas tre localis ni sur le lecteur A: ni sur le lecteur C: Accdez
lutilitaire de configuration et vrifiez si le disque fixe et le lecteur A: sont bien identifis et si la squence
damorage est bien configure. Le systme dexploitation devrait tre sur le lecteur C: sauf si vous avez
chang sensiblement votre installation. Si lutilitaire de configuration est bien install, votre disque dur
pourrait tre corrompu.
*Appuyez sur <F1> pour reprendre, sur <F2> pour CONFIGURER
Affich aprs tout message derreur rcuprable. Appuyez sur [F1] pour continuer le dmarrage ou sur
[F2] pour accder lutilitaire de configuration.
82 - Dpannage
Lhorloge de temps rel a chou le test du BIOS. Une rparation de la carte mre pourrait tre ncessaire.
Communiquez avec le service dassistance.
*Erreur de ventilateur, le systme sarrtera dans 30 secondes. Contactez le service de support
technique Fujitsu.
Une erreur de ventilateur sest produite. Communiquez avec votre reprsentant commercial.
*Une erreur de ventilateur sest produite durant lamorage.
Une erreur de ventilateur sest produite durant lamorage. Communiquez avec votre reprsentant commercial.
83 - Dpannage
POUR INSTALLER DES APPLICATIONS ET DES PILOTES, POUR COPIER LIMAGE DORIGINE ET LES IMAGES DE SYSTME,
POUR GRAVER UN DISQUE DE PILOTES ET DE RESTAURATION DAPPLICATIONS, DES DISQUES DAPPLICATIONS OU
DES DISQUES DAMORAGE, VOUS DEVEZ AVOIR UN GRAVEUR DE DVD INTERNE OU EXTERNE.
IL EST EXTRMEMENT IMPORTANT DE COPIER VOTRE IMAGE DORIGINE SUR DES SUPPORTS AMOVIBLES (P. EX. DISQUES
DVD). DANS LE CAS CONTRAIRE, VOUS RISQUEZ DE NE PAS POUVOIR RESTAURER LIMAGE UNE DATE
ULTRIEURE.
NOUS VOUS RECOMMANDONS DUTILISER DES DISQUES DE TYPE DVD-R OU DVD+R POUR VOS SAUVEGARDES,
MAIS LES SUPPORTS DE SAUVEGARDE DIMAGE SUIVANTS* SONT AUSSI PRIS EN CHARGE
POUR LIMAGE DORIGINE, LE DISQUE PRA, LES DONNES DAPPLICATIONS ET LE DISQUE DAMORAGE : DVD-R/+R.
POUR LES IMAGES DE SYSTME CRES PAR LUTILISATEUR : DVD-R/+R, DVD-RW/+RW, DVD-DL.
* SELON LE LECTEUR OPTIQUE ET LE FORMAT DU SUPPORT UTILIS, CERTAINS TYPES DE SUPPORTS PEUVENT NE
PAS CONVENIR LA CRATION DIMAGES DE SYSTME.
TANT DONN CERTAINES LIMITES LGALES, CERTAINES APPLICATIONS TIERCES DEVRONT TRE INSTALLES SPARMENT
LAIDE DU SUPPORT DAPPLICATIONS JOINT VOTRE ORDINATEUR.
Aprs avoir install lutilitaire ClickMe! lors du premier dmarrage de votre systme, une invite vous demandera
de faire une copie de limage dorigine sur des DVD. Plusieurs disques vierges (les DVD-R ou DVD+R
sont recommands) vous seront ncessaires pour crer la copie. Lorsque vous avez termin la copie, assurezvous dtiqueter clairement les disques et de les conserver en lieu sr.
Cration dimages de sauvegarde de limage dorigine, du disque PRA et dautres disques
SUR CERTAINS MODLES DE LIFEBOOK, LES APPLICATIONS NE SONT PAS SUR LE DISQUE DUR MAIS SUR LE
DISQUE PRA. VEUILLEZ PRENDRE CELA EN COMPTE EN LISANT LES PROCDURES QUI SUIVENT.
Le bouton [Grer/Changer] permet galement de crer des copies de sauvegarde de limage dorigine, du
disque PRA, du disque dapplications ou du disque damorage.
1
2
3
4
Vous voyez apparatre le message Le disque de restauration 1 sera cr. Inscrivez quelques commentaires
et un numro de disque sur le DVD. Cliquez sur [OUI] pour commencer graver limage dorigine.
Assurez-vous que la case indique le numro 2 (remarque : selon la taille de limage, il est possible que le chiffre
de limage dorigine indiqu soit suprieur).
POUR LTAPE SUIVANTE, VEILLEZ NE PAS UTILISER LORDINATEUR TANT QUE LA COPIE NEST PAS TERMINE.
Lorsque le systme copie, il affiche un cran criture sur disque avec une barre de progression. Une fois
lopration termine, une bote de dialogue vous informe que la copie de sauvegarde a t cre avec succs.
85 - Restaurer vos logiciels prinstalls
Rptez la procdure avec les trois autres disques dimages (disque damorage, disque de pilotes et de restauration
dapplications, disque dapplications). Le nombre dimages disponibles peut varier selon le modle du systme ;
sur certains modles, les applications ne sont pas charges sur le disque dur.
Si vous dsirez restaurer votre image dorigine, excutez les oprations indiques en page 3 dans la rubrique
Excution de la fonctionnalit Restauration et Utilitaires partir du disque dur .
Cration dune image de systme
Copies de sauvegarde de limage systme configures par lutilisateur : Sur votre bureau,
il existe une icne [MyRecovery] (Ma restauration) qui vous permet de faire des sauvegardes
My Recovery
de votre image systme actuelle sur un autre emplacement de votre disque dur ou sur un support
externe. Une image systme est un enregistrement de la configuration de votre unit de disque C : un moment
prcis. Il est conseill de faire occasionnellement une copie de scurit de limage systme afin de pouvoir
revenir certains stades prcdents sans avoir revenir au tout dbut, limage dorigine.
Par dfaut, les images de systme sont enregistres dans lunit de disque D : lintrieur du dossier
MyRecovery. Vous pouvez galement dcider denregistrer limage sur un disque dur externe.
1
2
3
Aprs le redmarrage, vous voyez apparatre une fentre Cration de limage de scurit vous proposant
de Crer limage sur lunit de disque D ou de Slectionner une unit de disque pour le cas o vous
prfreriez conserver limage sur un disque dur externe.
Vous voyez apparatre une illustration graphique de la faon dont limage sera enregistre. Cliquez sur
le bouton [Suivant].
5
6
Slectionnez un titre dimage dans la liste, puis cliquez sur le bouton correspondant laction que vous dsirez excuter.
Les outils Restauration et Utilitaires sont pr-installs en usine dans une partition cache et sont disponibles
sur le disque auto-amorage. Veuillez prendre note que si vous modifiez la configuration des partitions
de votre disque dur, vous risquez de supprimer les outils Restauration et Utilitaires . Dans un tel cas,
vous ne pourrez plus utiliser la partition cache pour lancer les outils Restauration et Utilitaires , mais
vous pourrez toujours amorcer le systme partir du disque.
Comment dterminer si la fonctionnalit Restauration et Utilitaires est dj installe
1
Allumez ou redmarrez votre systme. Lorsque le logo Fujitsu apparat, appuyez sur la touche [F12].
88 - Restaurer vos logiciels prinstalls
Dans le menu Amorage qui apparat, vrifiez si loption <Restauration et Utilitaires> est prsente. Si elle ny est pas,
cela signifie que la fonctionnalit doit tre utilise partir du disque. Si loption <Restauration et Utilitaires> nest
pas disponible, reportez-vous Excution de la fonctionnalit Restauration et Utilitaires partir du disque .
Allumez ou redmarrez votre systme. Lorsque le logo Fujitsu apparat, appuyez sur la touche [F12].
Lorsque la bote de dialogue Systme dexploitation apparat, slectionnez Utiliser les outils de restauration...
et cliquez sur [Suivant].
6
7
8
Avec le curseur, allez en bas de page jusqu <Restauration et Utilitaires>, puis appuyez sur [Entre].
Une barre de progression apparatra en bas de lcran pendant le transfert des fichiers partir du disque.
Lorsque la bote de dialogue Options de restauration du systme apparat, choisissez une nouvelle configuration
de clavier si ncessaire, puis cliquez sur [Suivant].
Lorsque la fentre Options de restauration du systme apparat, cliquez sur Restauration et Utilitaires .
Lcran Restauration et Utilitaires apparat avec trois onglets : Diagnostics, Restauration et Utilitaires. Veuillez
noter que longlet Diagnostics nest pas pris en charge par certains modles LIFEBOOK/Stylistic lorsque vous
excutez la fonction Restauration et Utilitaires partir du disque dur. Si vous dsirez restaurer le systme dexploitation,
utilisez licne du centre Restauration de limage dorigine (seulement unit de disque C :) sous longlet Restauration.
CE DISQUE PEUT SEULEMENT TRE UTILIS SUR LE SYSTME AVEC LEQUEL IL A T ACHET.
1
2
3
4
5
Mettez le systme sous tension. Lorsque le logo Fujitsu apparat lcran, appuyez sur la touche [F12].
Dans le menu qui apparat, slectionnez le menu Amorage.
Mettez en vidence loption CD/DVD et placez-la en tte de liste avec laide de la flche vers le haut.
Mettez le disque damorage sur le plateau du lecteur.
Cliquez sur [OK]. Une barre de progression apparatra en bas de lcran pendant le transfert des fichiers partir
du disque.
89 - Restaurer vos logiciels prinstalls
Lorsque la bote de dialogue Options de restauration du systme apparat, choisissez une nouvelle
configuration de clavier si ncessaire, puis cliquez sur [Suivant].
7
8
9
10
Onglet Diagnostics : Loutil de diagnostics est conu pour tre utilis par des informaticiens professionnels.
Il y a peu de chances que vous ayez besoin de lutiliser. Lorsque vous slectionnez des dispositifs dans la
fentre Diagnostic et que vous cliquez ensuite sur [Excuter], ceux-ci sont soumis plusieurs tests.
Onglet Restauration : Longlet Restauration comprend trois outils : Restauration de copies de systme
configures par lutilisateur , Restauration de limage dorigine (uniquement lunit de disque C :) et
Restauration de limage dorigine (restauration intgrale du disque dur) . Vous pouvez utiliser ces outils
pour restaurer limage dorigine partir de la partition cache, pour restaurer une image de sauvegarde cre
par vous ou des images enregistres sur des DVD, et pour restaurer compltement votre disque dur. Si vous
dsirez savoir comment crer des DVD de restauration de limage dorigine, des DVD dimage de systme
ou une copie interne de limage de systme, reportez-vous aux sections appropries ci-dessus.
Onglet Utilitaires : Longlet Utilitaires comprend trois outils : Supprimer les donnes sur le disque dur ,
Restaurer la fonctionnalit Restauration et Utilitaires et Restauration complte dordinateur Windows .
Lutilitaire Supprimer les donnes sur le disque dur permet de supprimer toutes les donnes sur votre
disque dur et den empcher leur rutilisation. REMARQUE : Nutilisez pas lutilitaire Supprimer
les donnes sur le disque dur , moins que vous soyez absolument certain de vouloir effacer
votre disque dur en entier, y compris toutes les partitions.
Restaurer la fonctionnalit Restauration et Utilitaires permet de restaurer la premire
partition cache.
Lutilitaire Restauration complte dordinateur Windows permet de restaurer une image cre
avec le Centre de restauration et de sauvegarde Windows. Lutilitaire Restauration complte dordinateur
Windows efface et rcrit toutes les donnes se trouvant sur le disque dur.
90 - Restaurer vos logiciels prinstalls
Si vous avez install un nouveau disque dur ou si votre disque dur na pas de fonction dauto-amorage,
excutez les oprations suivantes. Veuillez prendre note que vous devez dabord crer de nouvelles
partitions sur le disque dur, puis restaurer limage dorigine.
1
2
3
4
5
6
Mettez le systme sous tension. Lorsque le logo Fujitsu apparat lcran, appuyez sur la touche [F12].
7
8
9
10
11
12
13
14
15 Cliquez sur [Suivant] pour dmarrer la vrification. Cliquez sur [Suivant] nouveau lorsque la vrification est termine.
16 2. La mention Initialisation du disque dur saffichera en gras avec le message Veuillez insrer le disque
amorable dans le lecteur optique . Insrez le disque amorable. Cliquez sur [Suivant] pour continuer. Une
bote de dialogue saffiche, avec un message de vrification de disque.
17 Le message Attention ! Toutes les donnes du disque dur seront compltement effaces ! apparatra. Slectionnez
[OK]. Le processus de cration de partition dmarrera.
91 - Restaurer vos logiciels prinstalls
18 3. La mention Restauration de limage dorigine dans une partition cache est affiche en gras avec le message
Veuillez insrer le disque de restauration N 1 dans le lecteur optique . Cliquez sur [Suivant] pour continuer.
19 la fin du processus, loutil retournera automatiquement 3. Restauration de limage dorigine dans une partition
cache et affichera le message suivant : Veuillez insrer le(s) disque(s) dapplications en commenant par
le N1, puis cliquez sur [OK]. Insrez chaque disque lun aprs lautre jusqu les avoir tous installs. Si vous
navez pas de disque dapplications ou si vous avez insrs tous les disques dapplications. Cliquez sur [Annuler]
pour continuer. Vous avez alors deux choix :
21 Lorsque vous avez cliqu sur [Annuler], le message de confirmation suivant apparat : Si vous dsirez sauter
lopration de copie ou si cette operation est termine, cliquez sur [OK]. Cliquez sur [Annuler] si vous dsirez
retourner Restauration de limage dorigine sur une partition cache.
Permet une recherche manuelle des mises jour de pilotes. La premire fois que vous lutiliserez, on vous
demandera daccepter un contrat de licence. Aprs avoir cliqu sur licne, lutilitaire FDU se connectera
automatiquement au site Fujitsu pour vrifier les mises jour et les tlcharger. Pendant le processus de
tlchargement, licne affiche une barre rouge indiquant quelle ne peut pas tre utilise pendant que le
tlchargement est en cours. Lorsque la mise jour est termine, un message apparat pour vous en informer.
Activer les notifications de mises jour automatiques
Recherches automatiques de nouvelles mises jour sur une base rgulire (environ tous les 3 jours).
Afficher lhistorique des mises jour
Affiche un cran qui prsente un historique des mises jour effectues par lutilitaire FDU.
propos de lutilitaire FDU
Affiche le numro de version de lutilitaire FDU et des informations relatives aux droits dauteur.
Fichier Lisez-moi de lutilitaire FDU
Chapitre 5
Entretien
Entretien de votre ordinateur portable LIFEBOOK
Si vous prenez soin de votre ordinateur portable LIFEBOOK Fujitsu, vous augmenterez sa dure de vie
et sa fiabilit. Cette section fournit certains conseils relatifs lentretien de votre ordinateur portable et
de ses dispositifs.
LE SYSTME CONTIENT DES COMPOSANTS POUVANT TRE FORTEMENT ENDOMMAGS PAR UNE DCHARGE
LECTROSTATIQUE (DES). POUR MINIMISER CE RISQUE, VEUILLEZ PRENDRE LES PRCAUTIONS SUIVANTES :
AVANT DE CONNECTER OU DE DCONNECTER VOTRE ORDINATEUR PORTABLE LIFEBOOK (LORSQUE
VOUS UTILISEZ UN DUPLICATEUR DE PORTS), IL EST TOUJOURS RECOMMAND DE TOUCHER UN OBJET
MTALLIQUE MIS LA TERRE AFIN DE DCHARGER LLECTRICIT STATIQUE QUI SEST ACCUMULE
DANS VOTRE CORPS.
ASSUREZ-VOUS DE METTRE VOTRE SYSTME HORS TENSION AVANT DAJOUTER OU DE RETIRER DES
COMPOSANTS DU SYSTME. MME SI LE SYSTME EST EN TAT DE SOMMEIL OU DE VEILLE PROLONGE,
DES DONNES POURRAIENT TRE PERDUES ET LA MMOIRE ENDOMMAGE SI LE COURANT QUI ALIMENTE
LE SYSTME NEST PAS COUP.
LORSQUE VOUS INSTALLEZ OU RETIREZ UN MODULE DE MMOIRE, TENEZ-LE PAR LE BORD DE FAON
ASSUREZ-VOUS DE NE TOUCHER AUCUNE BORNE
DE CONNEXION NI AUCUN COMPOSANT INTERNE DE LORDINATEUR. LA PEAU DGAGE UNE SUBSTANCE
HUILEUSE QUI POURRAIT CAUSER UN COURT-CIRCUIT AUX COMPOSANTS.
TOUT QUIPEMENT LECTRIQUE PEUT TRE DANGEREUX SIL EST UTILIS DE FAON INAPPROPRIE. LE
FONCTIONNEMENT DE CE PRODUIT OU DAUTRES PRODUITS SIMILAIRES DOIT TOUJOURS SE FAIRE SOUS LA
SUPERVISION DUN ADULTE. NE PERMETTEZ PAS AUX ENFANTS DACCDER LINTRIEUR DE TOUT PRODUIT
LECTRIQUE ET NE LEUR PERMETTEZ PAS DEN MANIPULER LES CBLES.
NE TOUCHER AUCUN CONTACT NI AUCUNE PUCE.
94
Votre ordinateur portable LIFEBOOK est durable, mais cest un appareil lectronique sensible.
Traitez-le avec respect et prcaution.
Prenez lhabitude de transporter votre ordinateur dans une mallette convenable.
Nessayez pas de rparer lordinateur vous-mme. Suivez toujours les instructions dinstallation
la lettre.
Gardez-le loin de la nourriture et des boissons.
Pour protger votre ordinateur des dommages et optimiser ses performances, gardez toujours les
grilles de ventilation dgages, propres et sans dbris. Il est possible que vous deviez les nettoyer
priodiquement, selon lenvironnement dans lequel vous utilisez lordinateur.
Ne placez pas lordinateur dans un endroit o les grilles de ventilation pourraient tre obstrues,
notamment dans un petit espace ferm ou sur une surface molle comme un lit ou un coussin.
Si vous renversez par accident un liquide sur votre ordinateur portable LIFEBOOK :
1
2
3
4
teignez-le.
Positionnez-le de sorte que le liquide puisse sortir.
Laissez-le scher pendant 24 heures, ou plus si ncessaire.
Sil ne dmarre pas une fois sec, contactez le service dassistance.
Nutilisez pas votre ordinateur portable LIFEBOOK Fujitsu dans un environnement trs humide
( proximit dune baignoire, dune piscine).
Utilisez toujours ladaptateur secteur dorigine et des batteries homologues pour votre ordinateur
portable.
vitez dexposer lordinateur au sable, la poussire et dautres matires.
Nexposez pas votre ordinateur portable la lumire directe du soleil pendant de longues priodes,
car les tempratures de plus de 140 F (60 C) pourraient lendommager.
Gardez les caches des connecteurs et des fentes ferms lorsque ceux-ci ne sont pas en utilisation.
Ne dposez pas dobjets lourds ou tranchants sur lordinateur.
95 - Entretien de votre ordinateur portable LIFEBOOK
Si vous transportez votre LIFEBOOK dans un porte-documents, ou toute autre mallette, assurezvous quaucun objet dans ltui nappuie sur le couvercle.
Ne placez jamais votre ordinateur portable de faon ce que le lecteur optique supporte le poids
du portable.
Nettoyage de votre ordinateur portable LIFEBOOK
Dbranchez toujours la prise lectrique (tirez la fiche, pas le cordon).
Nettoyez votre ordinateur avec un chiffon humide, non pelucheux. Nutilisez pas de solvant
ou dabrasif.
Utilisez un tissu doux pour enlever la poussire de lcran. Nutilisez jamais de liquide lave-vitre.
Avant de nettoyer ou de dsinfecter lextrieur de votre ordinateur, le clavier ou lcran ACL,
prenez garde toujours teindre le systme, dbrancher ladaptateur secteur et retirer la batterie.
REMARQUE : Dans tous les cas, vitez de mouiller le revtement de type peau retourne.
Suivez les procdures de nettoyage en utilisant des produits nettoyants recommands
disponibles dans le commerce.
cran ACL
Pour nettoyer lcran, utilisez lun des nettoyants suivants :
Kit de nettoyage pour ordinateur portable Office Depot N 154-616
Lingettes Meridrew Enterprises Klear_Screen
* Convient aux crans des PC Tablettes, PC convertibles avec protecteur ACL et ordinateurs
portables standard.
Nettoyez lcran doucement et laissez-le scher avant dallumer votre ordinateur.
Dsinfection des ordinateurs LIFEBOOK
Nettoyez la surface de lordinateur laide dun tissu doux imbib dune solution dthanol 50 % ou
dun autre germicide base dthanol homologu par lEPA ( Environment Protection Agency , ou
Agence amricaine de protection de lenvironnement) en tant que dsinfectant hospitalier.
SI VOUS NUTILISEZ PAS LES BONS PRODUITS, LAFFICHAGE DE LCRAN ACL OU LORDINATEUR LUIMME PEUT EN TRE ENDOMMAG. POUR SAVOIR COMMENT UTILISER ET MANIPULER CONVENABLEMENT
LES PRODUITS NETTOYANTS, PRENEZ GARDE TOUJOURS CONSULTER LES PROCDURES DE
NETTOYAGE DU FABRICANT, AINSI QUE LES FICHES TECHNIQUES DE SCURIT.
Rangez votre ordinateur portable et les batteries sparment. Si vous rangez votre ordinateur
portable alors que la batterie est installe, la batterie se dchargera et sa dure de vie sera rduite.
De plus, une batterie dfectueuse pourrait endommager votre ordinateur.
Rangez votre Fujitsu LIFEBOOK dans un endroit frais et sec. Les tempratures doivent tre
maintenues entre -25C et 60C (13F et 140F).
TEIGNEZ TOUJOURS VOTRE ORDINATEUR AVANT DE LE TRANSPORTER ET/OU DE LEMBALLER. APRS
AVOIR TEINT LE SYSTME, ATTENDEZ QUE LE PANNEAU DE VOYANTS DTAT INDIQUE BIEN LE STATUT
HORS TENSION (CEST DIRE QUAUCUN VOYANT NEST ALLUM).
IL EST POSSIBLE QUE LAPPAREIL NE SE METTE PAS AUTOMATIQUEMENT EN MODE HORS TENSION
OU VEILLE PROLONGE APRS QUE VOUS AVEZ FERM LE COUVERCLE.
SE PRODUIRE EN FONCTION DES PARAMTRES DE SCURIT PAR MOT DE PASSE QUI GRENT
LA PR-INITIALISATION DU SYSTME OU DUNE AUTRE APPLICATION EN COURS DUTILISATION SUR
LORDINATEUR.
Apportez avec vous les adaptateurs de fiches ncessaires lorsque vous voyagez outre-mer.
Vrifiez le diagramme suivant pour dterminer quel adaptateur de fiche vous serait ncessaire
ou renseignez-vous auprs de votre agent de voyage.
Type de prise
Emplacement
Type de prise
Emplacement
Royaume-Uni, Irlande,
Malaisie, Singapour,
certains pays dAfrique
Chine, Australie,
Nouvelle-Zlande
Ne court-circuitez pas les terminaux des batteries (cest dire, ne touchez pas les deux terminaux
avec des objets mtalliques). Ne transportez pas des batteries dans votre poche ou sac main o
elles pourraient entrer en contact avec de la monnaie, des cls ou dautres objets mtalliques. Cela
pourrait causer une explosion ou un incendie.
Il ne faut jamais laisser tomber, percer, dsassembler, abmer ou incinrer une batterie.
Rechargez les batteries uniquement selon les instructions de ce manuel et seulement dans des
endroits ars.
Ne laissez pas les batteries dans des endroits chauds pendant plus dune journe ou deux. Les
grandes chaleurs risquent de raccourcir la dure de vie de votre batterie.
Ne rangez pas la batterie pendant plus de 6 mois sans la recharger.
Augmenter la dure de vie des batteries
Les disques multimdias sont des dispositifs prcis qui fonctionneront de manire fiable si vous en prenez
bien soin.
Rangez toujours vos disques multimdias dans leurs tuis lorsquils ne sont pas utiliss.
Tenez toujours les disques par les bords et vitez den toucher la surface.
vitez de ranger les disques multimdias dans des endroits o les tempratures sont extrmes.
Ne courbez pas les disques multimdias et ne dposez pas dobjets lourds par dessus.
Ne renversez pas de liquides sur les disques multimdia, ne les exposez pas la poussire.
Ngratignez pas les disques multimdias.
Si un disque multimdia subit un changement soudain de temprature, une condensation froid/chaud
pourrait se former sur la surface. Essuyez lhumidit avec un chiffon doux, propre et non pelucheux,
puis laissez le disque scher temprature ambiante. NUTILISEZ PAS de sche-cheveux ou
dautre appareil chauffant pour scher les disques multimdia.
Ncrivez jamais sur la surface de ltiquette avec un stylo bille ou un crayon. Utilisez toujours
un crayon-feutre.
Si un disque est sale, utilisez seulement un nettoyant pour DVD/CD ou essuyez-le avec un chiffon doux,
propre et non pelucheux : commencez par le bord intrieur et essuyez en direction du bord extrieur.
Entretien du lecteur optique
Votre lecteur optique est durable, mais vous devez en prendre soin. Veuillez faire attention aux
points suivants :
Le lecteur fait pivoter le disque compact une vitesse trs leve. Lorsquil fonctionne, vitez de le
dplacer ou de le soumettre des chocs ou des vibrations.
vitez dutiliser ou de ranger le lecteur dans un endroit o il serait expos des tempratures extrmes.
vitez dutiliser ou de ranger le lecteur proximit daimants ou de dispositifs qui gnrent de forts
champs magntiques.
101 - Entretien de votre ordinateur portable LIFEBOOK
Nutilisez pas et ne rangez pas le lecteur dans des endroits exposs des chocs ou des vibrations.
Ne dsassemblez pas ou ne dmontez pas le lecteur optique.
Lusage dun nettoyant spcial pour lentilles est recommand pour lentretien rgulier du lecteur.
Cartes MemoryStick/SD
Entretien de vos cartes
Les cartes ExpressCard et SD sont durables, mais vous devez en prendre soin. La documentation fournie
avec votre carte vous donnera des renseignements spcifiques, mais vous devriez aussi faire attention aux
points suivants :
Pour les protger de la poussire et de la salet, rangez vos cartes dans leurs tuis de protection
lorsquelles ne sont pas installes.
vitez toute exposition prolonge aux rayons du soleil ou une chaleur excessive.
Gardez les cartes au sec.
Ne flchissez pas ou ne courbez pas les cartes et ny placez pas dobjet lourd.
Ne faites pas entrer par force une carte dans une fente.
vitez de faire tomber les cartes ou de les exposer des vibrations excessives.
Chapitre 6
Spcifications techniques
Spcifications techniques du systme
Cette partie prsente les spcifications techniques du matriel et de lenvironnement de votre ordinateur
portable LIFEBOOK Fujitsu. Selon les configurations, les spcifications techniques peuvent varier.
tiquette de configuration
Ltiquette de configuration qui est situe sur le dessous de votre ordinateur portable comporte des informations
spcifiques propos des options que vous avez choisies pour votre ordinateur. Voici un exemple dtiquette
de configuration :
Numro de pice
Identifiant de configuration
No: CP4xxxxxxxxxxx
Part No: FPC0xxxxxxxxxxxxx
LH531, 14.0WXGA, i5-2410M , W7Pro, DL S-MULTI, 4GB, 500G, LAN, WLAN/BT
N de modle
Processeur
Taille dcran
Lecteur multimdia
Systme dexploitation
103
Disque dur
Mmoire
Communications
Microprocesseur
Nouveau Processeur Intel Core2010 2me gnration (reportez-vous ltiquette du systme pour
connatre la vitesse du processeur).
Puce
Intel HM65
Mmoire
Mmoire systme
Contrleur graphique Intel HD 3000. Le volume de mmoire vido partage dpend de la capacit de
mmoire du systme, soit :
Mmoire systme
(Windows 7 32-bit)
Mmoire graphique
maximum
Mmoire systme
(Windows 7 64-bit)
Mmoire graphique
maximum
1 Go
274 Mo
1 Go
274 Mo
2 Go
786 Mo
2 Go
786 Mo
4 Go
1 430Mo
4 Go
1 696 Mo
Audio
Codec Realtek ALC269 avec systme audio haute dfinition (HD) deux canaux.
couteurs : couteurs stro/sortie audio, 3,5 mm, 1 Vrms ou moins, impdance min. 32 ohms
Microphone : Prise dentre de ligne/microphone stro, 3,5 mm, 100 mV crte--crte ou moins,
impdance min. de 10 Kohms.
Deux haut-parleurs stro intgrs sans botier
Options de mmoire de masse
Disque dur
Serial ATA, 5400 r/m, 2.5. La capacit et la vitesse du disque dpendent de la configuration du systme.
Lecteur optique
Selon votre configuration systme, les lecteurs optiques suivants sont fournis :
Lecteur mixte Blu-ray multiformat double couche : criture : 8x DVD-R (SL), 8x DVD+R (SL),
6x DVD-R (DL), 6x DVD+R (DL), 6x DVD-RW, 8x DVD+RW, 5x DVD-RAM, 24x CD-R, 6x CD-RW
(US, US+)
Alimentation
Batterie
Conforme la norme ACPI (Advanced Configuration and Power Interface, ou Interface avance de configuration
et de gestion de lnergie).
Dimensions et poids
Dimensions gnrales
Environ 335 mm de largeur x 240 mm de profondeur x 35,4 mm dpaisseur (13,19 po x 9,45 po x 1,39 po)
Poids
Tous les systmes dexploitation et la plupart des logiciels dapplication ont des didacticiels intgrs ds
leur installation. Nous vous recommandons vivement de passer en revue le tutorial avant dutiliser une
application.
Guides
Sont compris dans votre portable, les guides dutilisation pour votre systme dexploitation et les autres
applications prinstalles. Tous les guides dutilisation non prsents sont disponibles en ligne par lintermdiaire
du systme daide du logiciel. Nous vous recommandons de passer en revue ces guides dutilisation pour
obtenir des informations sur lutilisation des logiciels.
Adobe Reader
Adobe Reader permet de consulter et dimprimer des fichiers PDF sur toutes les plateformes
informatiques courantes.
Roxio Creator
Roxio Creator vous permet de graver facilement des CD ainsi que dorganiser, dditer et de partager des
photos numriques, de la musique, des donnes, ou des vidos.
Norton Internet Security
Votre systme est prinstall avec une version Norton Internet Security dessai de Symantec valable
60 jours. La gamme doutils Norton Internet Security est conue pour protger votre ordinateur portable
contre les virus, les pirates, les logiciels espions et les pourriels. Il aide la protection des donnes
actuellement sur votre disque dur contre toute infection ou destruction. La version dessai est active aprs
acceptation du contrat de licence du logiciel. Aprs 60 jours, vous devrez vous procurer un abonnement
auprs de Symantec pour pouvoir tlcharger les signatures de virus, de logiciels espions et de pourriel les
plus rcentes.
CyberLink PowerDVD
CyberLink PowerDVD vous permet de lire des DVD sur votre ordinateur.
109 - Spcifications techniques du systme
CyberLink Makedisc
CyberLink MakeDisc vous permet de graver des donnes, des vidos et des photographies sur des CD ou
des DVD.
CyberLink PowerDirector
CyberLink PowerDirector vous permet dditer et damliorer vos vidos en les agrmentant notamment
deffets spciaux.
CyberLink YouCam
La webcam intgre CyberLink YouCam vous permet de prendre des photos ou des films, dy ajouter des
effets spciaux, et de les partager sous divers formats ou par lintermdiaire de rseaux sociaux.
Google Toolbar (Barre doutils Google)
La barre doutils Google vous permet de faire des recherches rapides sur Internet, de bloquer les fentres
et de raliser une gamme varie de tches pour rendre votre utilisation dInternet plus facile et plus plaisante.
Microsoft Windows Live Essentials
Windows Live Essentials est une suite de programmes vous permettant dutiliser votre LIFEBOOK avec
plus daisance et de plaisir. Live Essentials comprend six applications Live : Messenger, Photo Gallery, Writer,
Mail, Movie Maker et Silverlight. Messenger vous permet de communiquer et dchanger rapidement avec
des personnes ou des groupes. Photo Gallery est une application souple dutilisation vous permettant dorganiser,
de modifier et de partager vos photos. Writer vous permet de publier des textes sur votre blog, dy tlcharger
des vidos et des photos, et en gnral de publier des textes en ligne. Mail vous permet de grer votre messagerie.
Movie Maker vous permet de crer des films et des diaporamas de trs bonne qualit partir de vos vidos
et photos. Limportation de vidos et photos haute dfinition ou standard est trs simple, et lajout danimations,
de musique et de titres ne prendra que quelques minutes grce AutoMovie. Quant Silverlight, cette
application rendra votre exprience encore plus passionnante grce au partage de fichiers vido de grande
qualit sur Internet et sur appareils mobiles.
Microsoft Office Starter 2010
Microsoft Office Starter 2010 est une suite logicielle comprenant les versions simplifies de Word 2010
et dExcel 2010 avec des publicits. PowerPoint, Outlook et Publisher NE SONT PAS inclus. Pour activer
la version complte dOffice sur cet ordinateur, achetez une carte de cl produit Office 2010.
110 - Spcifications techniques du systme
Glossaire
ACL
Affichage cristaux liquides. Type dcran produisant des images par contrle de lorientation
de cristaux dans un liquide cristallin.
ACPI (Advanced Configuration and Power Interface)
Un dispositif qui convertit le courant continu dun allume-cigare de voiture ou une prise c.c. davion
en courant continu lintensit voulue pour alimenter votre portable LIFEBOOK.
Adaptateur secteur
Appareil convertissant une tension c.a. provenant dune prise murale en un courant c.c. ncessaire
lalimentation de votre ordinateur portable LIFEBOOK.
Adresse IP
Un identifiant pour un ordinateur ou un priphrique sur un rseau TCP/IP. Les rseaux qui utilisent le
protocole TCP/IP acheminent des messages en fonction de ladresse IP de la destination. Le format
dune adresse IP est une adresse numrique de 32 bits qui scrit avec quatre nombres spars par des
points. Chaque numro peut aller de 0 255. Par exemple, 1.160.10.240 pourrait tre une adresse IP.
111
Au sein dun rseau isol, vous pouvez attribuer des adresses IP au hasard tant que chacune delles
reste unique. Toutefois, la connexion dun rseau priv Internet exige lutilisation dadresses IP
enregistres (appeles adresses Internet) afin dviter les doublons.
Les quatre numros dans une adresse IP sont utiliss de diffrentes faons pour identifier un rseau
particulier et un serveur hte. Trois registres rgionaux Internet (ARIN, RIPE NCC et APNIC)
attribuent des adresses Internet partir des trois classes suivantes :
Classe A : accepte 16 millions de serveurs sur chacun des 126 rseaux.
Classe B : accepte 65 000 serveurs sur chacun des 16 000 rseaux.
Classe C : accepte 254 serveurs sur chacun des 2 millions de rseaux.
Le nombre dadresses Internet non attribues commence manquer, aussi un nouveau schma sans
classe, appel CIDR, remplace de plus en plus le systme bas sur les classes A, B et C et est rattach
ladoption de la norme IPv6.
Adresse MAC (Media Access Control)
Adresse de contrle daccs au mdia. Adresse physique unique dune carte rseau. Pour Ethernet, les
trois premiers octets sont utiliss pour indiquer le code du vendeur, contrl et attribu par lIEEE. Les
trois autres octets sont contrls par chaque fabricant (pour empcher toute superposition) ; en
consquence, chaque carte Ethernet reoit une adresse physique unique au monde, ce qui permet de la
distinguer parmi dautres cartes. Lorsque la technologie Ethernet est utilise, des trames sont envoyes
et reues en fonction de cette adresse.
ADSL (Asymmetric Digital Subscriber Line)
Ligne numrique paire asymtrique. Technologie de transport de services haut dbit sur des lignes
tlphoniques ordinaires.
AGP (Accelerated Graphics Port)
Littralement : Port graphique acclr . Port local spcialement conu pour les priphriques
utilisant beaucoup dimages graphiques, notamment les cartes vido et les acclrateurs 3D.
112 - Glossaire
Amorage
Dmarrage dun ordinateur et chargement de son systme dexploitation dans la mmoire vive
(RAM), partir du disque, de la mmoire ROM ou dautres supports de stockage.
Authentification cl partage
Mthode dauthentification rseau tablie par la spcification 802.11, selon laquelle le point daccs
transmet au client un paquet texte que le client doit crypter avec la bonne cl de rseau et renvoyer au
point daccs. Si le client possde la mauvaise cl ou sil nen a pas, lauthentification chouera et il
ne sera pas autoris sassocier au point daccs. Lauthentification cl partage nest pas considre
comme une mthode sre, car un pirate qui accde au texte en clair et au texte crypt avec la cl WEP
pourrait dchiffrer celle-ci.
Authentification ouverte
Mthode dauthentification tablie dans la norme 802.11 selon laquelle un client sans fil nest pas
authentifi avant de pouvoir sassocier.
Batterie au lithium
Type de batterie rechargeable ayant une puissance et une dure de vie importantes compte tenu de sa
taille, et ne subissant pas leffet de mmoire qui caractrise les batteries au nickel-cadmium.
BIOS
Acronyme signifiant Basic Input-Output System. Programme et ensemble de paramtres par dfaut
stocks dans la mmoire morte : il effectue des diagnostics et fait fonctionner votre ordinateur lorsque
vous le mettez sous tension, et agit ainsi jusqu ce que votre systme dexploitation se soit charg
partir du disque. Les informations du BIOS sont transfres au systme dexploitation pour lui fournir
des donnes sur la configuration et ltat du matriel.
Bit
Contraction de Binary digit . Unit simple dinformation pouvant adopter la valeur 1 (un) ou 0 (zro).
bit/s
Abrviation de bits par seconde . Unit utilise pour mesurer le dbit de transfert de donnes.
113 - Glossaire
Bus
Circuit lectrique qui transmet des donnes entre lunit centrale et les sous-ensembles lintrieur
de lordinateur.
c.c.
Plage de frquences bande troite utilise par la carte rseau sans fil pour transmettre des donnes.
IEEE 802.11b/g : 11 canaux dans la bande de 22 MHz.
CardBus
Version 32 bits plus rapide de linterface PC Card dont les performances sont similaires celles de
larchitecture PCI 32 bits.
Cathodique (CRT Cathode Ray Tube, ou Tube rayons cathodiques)
Tube rayons cathodiques. Moniteur dont laffichage est assur par un faisceau de particules
lectroniques qui frappe lcran luminescent. Une image est produite par la variation de la position
et de lintensit du faisceau.
CD-ROM
Disque compact mmoire morte. Forme de stockage de donnes numriques lues optiquement par
un faisceau laser plutt que par une tte magntique. Gnralement, un CD-ROM peut contenir
environ 600 Mo de donnes et permet dviter les problmes dcrasement de la tte qui dtruisent des
donnes, ainsi que lusure durant la lecture.
Cl de chiffrement (cl rseau)
Cl de chiffrement utilise pour coder les textes de messages et pour effectuer les vrifications de lintgrit
des messages. La cl de chiffrement protge les donnes contre les interceptions non autorises.
Ce dispositif utilise la mme cl de chiffrement pour coder ou dcoder les donnes ; cette dernire est
obligatoire pour que lmetteur et le receveur puissent communiquer.
114 - Glossaire
Cl de rseau
Cl utilise pour le chiffrement des donnes sur le rseau. La cl de rseau tant utilise par
lordinateur personnel pour crypter et dcrypter les donnes, lmetteur et le rcepteur doivent
utiliser la mme cl.
Commande
Instruction que vous transmettez au systme dexploitation. Exemple : excuter une application
particulire ou formater une disquette.
Compatibilit Wi-Fi
Contraction de Wireless Fidelity . Une conformit Wi-Fi indique que le produit a russi le test
dinteroprabilit de la WECA (Wireless Ethernet Compatibility Alliance), ce qui garantit linteroprabilit
de produits de rseau sans fil IEEE 802.11. Pour plus de renseignements sur la norme Wi-Fi, visitez
le site Web de la WECA : www.wirelessethernet.com.
Configuration
Dcharge lectrostatique. Dcharge lectrostatique soudaine provenant dune charge statique qui
sest accumule lentement. Exemple : la dcharge reue dune poigne de porte ou les tincelles
gnres par un brossage des cheveux par temps sec.
DHCP (Dynamic Host Configuration Protocol)
Il sagit dun protocole qui permet un ordinateur qui se connecte sur un rseau dobtenir
dynamiquement sa configuration. Il est utilis pour rcuprer automatiquement des paramtres
ncessaires la communication, tels des adresses IP. Lmetteur dune adresse IP sappelle un
serveur DHCP, et celui qui reoit est un client DHCP.
DIMM
Disque
Support circulaire et plat pour le stockage magntique de donnes. Sil est rigide, il est appel disque
dur. Sil est flexible, il est appel disque souple. Un disque souple log dans un botier rigide dot dun
volet est communment appel disquette.
Disque dur
Support rotatif, circulaire, plat et trs rigide pour le stockage magntique de donnes.
Disquette
Accs direct la mmoire. Circuit spcial de transferts de donnes de mmoire mmoire ne ncessitant
pas lintervention de lUC.
DMI (Desktop Management Interface)
Interface de gestion du mode bureau. Norme qui permet aux applications de gestion dordinateur
dinterroger et de configurer, localement ou distance, des systmes informatiques, des composants
matriels et logiciels, ainsi que des priphriques.
DNS (Domain Name System)
Systme dadressage par domaines Fonction qui contrle la correspondance entre ladresse IP et le
nom attribu lordinateur. Il est possible de communiquer avec les ordinateurs dont les adresses IP
sont inconnues, mais dont le nom est connu.
Donnes
Technologie DVMT ou de mmoire vive pour les fonctions vido. Topologie de mmoire vido
permettant damliorer lefficacit de la carte mre grce une utilisation innovante de la mmoire
et une exploitation en direct de lAGP (port graphique acclr).
116 - Glossaire
E/S
Type dcran plat o un transistor ou un composant similaire est associ chaque pixel de lcran.
FCC (Federal Communication Commission)
Oscillateur frquence prcise qui synchronise le fonctionnement du systme et tablit lheure et la date.
IDE (Intelligent Drive Electronics)
Interface IDE Linterface IDE se caractrise par le fait que le contrleur lectronique du disque dur est
intgr dans le mme botier que ce dernier.
IEEE 802.11a
Norme de rseau sans fil autorisant un dbit maximum thorique de 54 Mbit/s. Les cartes de norme
802.11a fonctionnent dans les bandes de frquences UNII infrieures et intermdiaires de 5 GHz.
IEEE 802.11b
Norme de rseau sans fil autorisant un dbit maximum thorique de 11 Mbit/s. Les cartes de norme
802.11b fonctionnent dans les bandes de frquences ISM de 2,4 GHz.
IEEE 802.11g
Norme de rseau sans fil autorisant un dbit maximum thorique de 54 Mbit/s. Les cartes de norme
802.11g fonctionnent dans les bandes de frquences ISM de 2,4 GHz.
117 - Glossaire
Infrarouge
Lumire dont la frquence est juste en de de la partie rouge du spectre optique visible par lil humain.
Infrastructure
Nom dune configuration de rseau local (LAN) sans fil. Ce type de communication utilise un point
daccs. Il existe galement un autre type de communications appel Ad hoc .
IR
Abrviation de infrarouge .
IrDA (Infrared Data Association)
Association pour le transfert de donnes par infrarouge. Une organisation de constructeurs qui
dveloppe les normes de communication utilisant linfrarouge pour transmettre les donnes.
IRQ (Interrupt Request)
Demande dinterruption. Il sagit dun signal envoy par le matriel lunit centrale indiquant quil
y a ncessit de traiter un vnement externe qui vient de se produire.
Ko
Dispositif qui fait tourner le disque et qui contient les ttes et les circuits de commande permettant
la lecture et lcriture de donnes sur le disque.
118 - Glossaire
Masque de sous-rseau
Le rseau TCP/IP est command laide dune division en plusieurs sous-rseaux. Une adresse IP
se compose dune adresse de sous-rseau et de ladresse de lordinateur. Le masque de sous-rseau
dtermine le nombre de bits formant ladresse de sous-rseau dans ladresse IP. La mme valeur doit
tre utilise pour tous les ordinateurs qui doivent communiquer sur le rseau.
Mgahertz
Dpt de donnes et dapplications auquel lunit centrale de votre ordinateur portable LIFEBOOK
a directement accs.
Mmoire cache
Bloc de mmoire intgr au microprocesseur, auquel il est beaucoup plus rapide daccder qu la
mmoire vive et utilis de manire spciale pour acclrer le dbit global des donnes.
MHz
Mga-hertz
MIDI (Musical Instrument Digital Interface)
Le mode Ad Hoc dsigne une topologie de rseau sans fil dans laquelle la connectivit entre les divers
ordinateurs est tablie sans priphrique central de rseau sans fil, ou point daccs. La connectivit
est tablie uniquement laide de priphriques clients dans une configuration gal gal. Pour plus
de dtails, voir Mode Ad hoc on page 131
119 - Glossaire
Modem
Carte de circuit imprim avec mmoire et circuit associ qui permet lutilisateur dajouter de la
mmoire supplmentaire ?? lordinateur sans outil spcial.
Mono
Systme qui utilise un seul canal pour traiter le son provenant de toutes les sources.
MTU (Maximum Transmission Unit)
La configuration dun rseau local sans fil fait appel un regroupement pour viter les interfrences
et le vol de donnes. Ce regroupement est effectu avec le Nom de rseau (SSID) . Pour amliorer
la scurit, la cl de rseau nautorise aucune communication si le SSID ne lui correspond pas.
NTSC (National TV Standards Commission)
Commission nationale des normes TV. Norme de diffusion et de rception tlvisuelle aux tats-Unis.
Octet
Bloc despace rserv sur un disque dur, que le systme dexploitation considre comme tant un
disque distinct et quil gre en consquence.
120 - Glossaire
PCMCIA est une marque de commerce de la Personal Computer Memory Card International
Association. La PCMCIA (association internationale des cartes de mmoire pour ordinateur
personnel) est lorganisme qui dfinit les normes relatives aux cartes dextension pour ordinateurs.
Priphrique
quipement qui effectue une fonction spcifique associe un ordinateur mais qui ne fait pas partie
de cet ordinateur. Exemples : imprimante, modem, CD-ROM.
Pilote
Programme qui traduit les commandes envoyes par les applications et le systme dexploitation aux
priphriques externes dans la forme exacte exige par une marque et un modle particulier afin de
produire les rsultats voulus avec le matriel employ.
Pixel
Le plus petit lment daffichage, point de couleur lcran. Plus la densit de pixels est leve, plus
limage est nette.
Point daccs
Priphrique de rseau sans fil servant de pont de communication entre un rseau sans fil et un rseau cbl.
Port COM
Connecteur et circuits de commande associs travers lesquels transitent les donnes lectroniques
entrant et sortant de votre ordinateur.
121 - Glossaire
Port srie
Connexion un autre priphrique par lequel les donnes sont transfres raison dun bit la fois
sur un seul fil conducteur, les autres fils conducteurs servant la commande du priphrique et non au
transfert de donnes.
POST (Power On Self Test)
Auto-diagnostic (ou auto-test) de mise sous tension. Programme faisant partie du BIOS, qui vrifie la
configuration et les conditions de fonctionnement de votre matriel chaque fois que votre portable est
allum. Des messages dtat et derreur peuvent tre affichs avant que le systme dexploitation ne
se charge. Si lautotest dtecte une panne qui est si importante que le fonctionnement ne peut pas
continuer, le systme dexploitation ne sera pas charg.
PPPoE (Point to Point Protocol over Ethernet)
Littralement, Protocole Ethernet Point Point Protocole Ethernet faisant appel au protocole point
point (PPP) et utilis pour la connexion une ligne tlphonique.
Programme
Ensemble intgr de commandes codes indiquant lordinateur ce qui doit tre fait, ainsi que quand
et comment le faire.
Protocole
Mmoire accs direct, ou mmoire vive. Composant matriel de votre ordinateur LIFEBOOK
qui stocke des informations binaires (programme et donnes) tant quil est aliment par une source
de courant.
122 - Glossaire
Voir Rinitialisation.
Rinitialisation
Le fait de charger nouveau le systme dexploitation. Une rinitialisation efface toutes les
informations stockes dans la mmoire vive.
Reprise
Continuer aprs une interruption. Dans le cas de votre portable, ceci signifie la reprise des activits
normales partir de lun des modes de veille.
ROM (Read Only Memory)
Mmoire en lecture seule, ou mmoire morte. Type de mmoire o les donnes sont stockes par
transformation physique de la matire. Les donnes stockes de cette faon ne peuvent pas tre
modifies par lordinateur et leur conservation nexige pas de source de courant.
SDRAM
Identificateur de services 32 caractres ajout lentte des paquets transmis sur un rseau sans fil,
qui sert de mot de passe lorsquun priphrique mobile tente de se connecter lensemble de services
de base (BSS, ou Basic Service Set en anglais). Lidentifiant SSID distingue un rseau sans fil dun
autre, de telle manire que tous les points daccs et priphriques qui tentent de se connecter un
rseau donn doivent utiliser le mme identifiant. Un priphrique ne peut tre autoris accder au
BSS que sil fournit le SSID unique. Le SSID tant diffus en texte clair, il nassure aucune scurit
du rseau.
123 - Glossaire
Stro (audio)
Systme qui utilise deux canaux pour traiter le son provenant de deux sources diffrentes.
S-Vido
Super Vido. Systme vido composantes servant grer un cran de tlviseur ou dordinateur.
Systme dexploitation
Groupe de programmes de contrle qui convertissent les commandes des applications, y compris les
pilotes, dans la forme exacte exige par une marque et un modle particuliers de processeur afin de
produire les rsultats voulus avec le matriel employ.
TCP/IP (Transmission Control Protocol/Internet Protocol)
Abrviation de Thin Film Transistor . Technologie dcrans plats qui utilise une mince matrice de
transistors pour commander individuellement chaque pixel de lcran.
UL (Underwriters Laboratories)
L Underwriters Laboratories est un organisme indpendant qui effectue les tests de scurit
lectrique des appareils et accorde les homologations correspondantes.
USB
124 - Glossaire
Veille
Mode dans lequel lordinateur est temporairement inactif. Votre LIFEBOOK utilise plusieurs modes
de veille afin de rduire la consommation lectrique et de prolonger la charge de votre batterie.
Voyant dtat
Voyant indiquant ltat de certains composants de votre systme. Sur votre ordinateur portable
LIFEBOOK, il sagit dun cran ACL situ juste au-dessus du clavier.
VRAM (Video Random Access Memory)
Mmoire vive vido. Mmoire rserve aux donnes et au contrle daffichage vido.
WFM (Wired for Management)
Abrviation de Wired for Management . Vaste programme dIntel visant rduire les cots globaux
de linformatique de gestion, sans sacrifier la puissance et la souplesse.
WLAN (Wireless Local Area Network)
Rseau local sans fil. Interconnexion sans fil dordinateurs et de priphriques dans un emplacement
gographiquement dlimit et permettant lchange de programmes et de donnes.
125 - Glossaire
Cet appareil a t test et jug conforme aux limites tablies pour le matriel numrique de classe B,
selon la Partie 15 des rglements de la FCC.
Ces limites sont conues pour assurer une protection raisonnable contre les interfrences nuisibles dans
un environnement rsidentiel. Cet appareil gnre, utilise et met de lnergie radiofrquence et, si son
installation et son utilisation ne sont pas conformes aux instructions, il peut tre la cause de parasites
nuisibles aux communications radio. Il nest toutefois pas garanti quaucune interfrence ne sera observe
dans un environnement particulier. Si ce matriel cause des interfrences nuisibles la rception des ondes
de radio ou de tlvision, ce qui peut tre vrifi en le mettant hors tension puis sous tension, lutilisateur
devra tenter de les corriger en procdant comme suit :
Rorienter ou dplacer lantenne rceptrice.
Accrotre la distance entre lappareil et le rcepteur.
Brancher lappareil sur une prise relie un circuit diffrent de celui sur lequel le rcepteur est branch.
Consulter le vendeur ou un technicien radio/tlvision expriment pour obtenir de laide.
Des cbles de liaison paires torsades blindes doivent tre utiliss pour assurer la conformit aux limites
dmission RF qui gouvernent ce dispositif.
AVIS DOC (INDUSTRIE CANADA)
Avis aux utilisateurs de postes radio et de tlviseurs
127
1
2
3
4
129 -
La carte rseau sans fil peut tre utilise selon quatre modes de fonctionnement : IEEE 802.11b,
IEEE 802.11g et IEEE 802.11n (version prliminaire).
La carte rseau sans fil est certifie Wi-Fi et fonctionne un dbit maximal thorique de 540 Mbit/s en mode
IEEE 802.11n, de 54 Mbit/s en mode IEEE 802.11g, et de 11 Mbit/s en mode IEEE 802.11b.
La carte rseau sans fil prend en charge les modes de chiffrement WEP, TKIP, CKIP et AES.
La carte rseau sans fil est conforme aux normes suivantes : WPA, WPA2, CCX1.0, CCX2.0, CCX3.0
et CCX4.0.
Le mode Ad hoc dsigne une topologie de rseau sans fil dans laquelle la connectivit entre les divers
ordinateurs est tablie sans priphrique central de rseau sans fil, ou point daccs. La connectivit est
tablie uniquement laide de priphriques clients dans une configuration gal gal. Les rseaux Ad
hoc sont donc galement connus sous le nom de rseaux dgal gal. Un rseau Ad hoc est une mthode
aise et peu coteuse de relier plusieurs ordinateurs en rseau.
Le mode Ad hoc exige que les paramtres de nom de rseau SSID (service set identifier),
dauthentification rseau et de cl de chiffrement soient configurs de faon identique sur tous les
ordinateurs du rseau.
Rseau en mode Ad hoc
Le mode Infrastructure dsigne une topologie de rseau sans fil dans laquelle les appareils communiquent
au sein dun rseau sans fil ou cbl par lintermdiaire dun point daccs. En mode Infrastructure, les
appareils sans fil peuvent communiquer directement entre eux ou sur un rseau cbl. Les rseaux sans
fil dentreprise fonctionnent en mode Infrastructure car ils doivent se servir du rseau local sans fil pour
accder aux ordinateurs, aux priphriques et aux services (par exemple, serveurs de fichier, imprimantes
et bases de donnes).
Rseau en mode point daccs (Infrastructure)
Internet
Modem ADSL
modem cble,
ou similaire
Point daccs*
Rseau local
sans fil
La carte rseau local sans fil est un dispositif en option qui peut tre fourni avec votre ordinateur portable.
Normalement, vous ne devriez pas avoir besoin de la retirer ou de la rinstaller. Le systme dexploitation
de lordinateur est dj configur pour utiliser la carte rseau sans fil.
Remarques concernant les rseaux sans fil
La carte rseau sans fil fonctionne dans les modes IEEE802.11b, IEEE802.11g et IEEE802.11n.
Elle utilise la bande de frquence ISM de 2,4 GHz.
Les fours micro-ondes peuvent interfrer avec la carte rseau sans fil car ils utilisent la mme bande
de frquences (2,4 GHz) que les spcifications IEEE 802.11b/g/n.
Les appareils sans fil qui mettent dans la bande de frquences de 2,4 GHz peuvent nuire au fonctionnement
des priphriques IEEE 802.11b/g/n. Les symptmes associs aux interfrences incluent une rduction
du dbit, des coupures intermittentes de connexion et un nombre important derreurs de trames. Il est
FORTEMENT recommand de mettre hors tension les appareils gnrant des interfrences afin dassurer
le bon fonctionnement de la carte rseau sans fil.
Sans fil
Utilitaire
Commutateur
Notez quavec cette procdure, la radio ne sera pas teinte, lmission et la rception sont toujours actives
bien que la carte ne soit plus connecte.
1
2
Faites un clic droit sur licne Carte rseau sans fil dans la zone de notification en bas droite de lcran.
Choisir Se dconnecter dun rseau.
3
4
5
Entrez les informations requises. Pour obtenir ces renseignements, il est possible que vous deviez consulter
votre administrateur de rseau.
Dans lventualit dun besoin daide, allez la fentre du Centre de rseau et partage (Dmarrer -> Panneau
de configuration -> Centre de rseau et partage) et entrez les mots-cls dans la bote Recherche.
Se connecter un rseau
Aprs avoir configur votre ordinateur, vous pouvez vous connecter un rseau actif en ralisant les
tapes suivantes :
1
2
3
Connexion au rseau
Une fois la configuration effectue, vous pouvez vous connecter un rseau actif en cliquant sur licne
Connexion rseau sans fil de la zone de notification.
Cause possible
Solution possible
Connexion de
rseau non
disponible
Problme
Cause possible
Solution possible
Connexion de
rseau non
disponible
(suite)
Lordinateur
connecter est teint.
Interfrences RF
provenant de points
daccs ou dautres
rseaux sans fil
chec de
lauthentification de la
carte rseau sans fil.
Configuration incorrecte
de ladresse IP
Spcification
Type de rseau
La carte Atheros XSPAN 802.11bgn (HB95) intgre est conforme aux normes
802.11b/g et 802.11n sur les applications Wi-Fi*.
Dbit
Frquence active
Nombre de canaux
802.11n :
2,4 GHz - 3 sans chevauchement si la liaison entre rseaux nest pas utilise,
2 sans chevauchement si la liaison entre rseaux est utilise.
Scurit
Types de chiffrement compatible avec WEP, TKIP, AES***, WPA 1.0 et WPA2, CCX
Longueurs de cls de chiffrement prises en charge : 64 bits et 128 bits 802.1x/EAP
10 ou moins****
Porte nominale**
*
Type Wi-Fi indique que le test dinterconnectivit de la Wi-Fi Alliance a russi.
**
La porte peut varier selon certains facteurs (par exemple : nombre de murs, rflectivit des
matriaux ou interfrences provenant dautres sources de radiofrquences).
***
Le chiffrement par cl de rseau (WEP) est effectu avec le nombre de bits indiqu ci-dessus, mais
lutilisateur peut dfinir une cl de 40 ou 104 bits aprs avoir soustrait la longueur fixe de 24 bits.
****
Selon lenvironnement, le nombre maximum dordinateurs peut tre infrieur.
Utilisation de Bluetooth
Le module Bluetooth intgr (QBTM400) est un composant offert en option pour les ordinateurs
portables Fujitsu.
Prsentation de Bluetooth
La technologie Bluetooth est conue pour assurer la liaison sans fil faible porte entre divers appareils
mobiles, tels que tlphones, ordinateurs portables, imprimantes et camras. La technologie Bluetooth
permet dtablir des rseaux personnels (PAN) entre des appareils situs courte distance les uns des autres.
POUR ACTIVER OU DSACTIVER SPARMENT LA CARTE DE RSEAU LOCAL SANS FIL OU BLUETOOTH,
PROCDEZ COMME SUIT :
Cet quipement respecte les normes de la FCC relatives lexposition aux rayonnements, dfinies pour
un environnement non contrl. Lantenne Bluetooth est situe sur le rebord avant du repose-mains droit
et est exempte des critres de distance minimale en raison de sa faible puissance.
Les metteurs de ce priphrique ne doivent pas tre utiliss avec ou proximit immdiate dune antenne
ou dun autre metteur.
Avis pour le Canada
Pour viter que ce service fourni sous licence soit perturb par des interfrences radio, ce matriel doit tre
utilis lintrieur et distance des fentres. Si lquipement (ou lantenne de transmission) est install
lextrieur, une licence peut tre ncessaire.
Garantie
Les utilisateurs ne sont pas autoriss modifier ce produit. Toute modification annule la garantie.
Cet quipement ne peut tre modifi, altr ou chang en aucune faon sans lautorisation crite
de Fujitsu. Toute modification non autorise annulera les autorisations dquipement de la FCC
et dIndustrie Canada, de mme que la garantie.
142
SI VOUS AVEZ ACHET UN SYSTME AVEC CARTE RSEAU LOCAL SANS FIL INTEL ET TECHNOLOGIE INTEL WIDI
EN OPTION, IL POSSIBLE QUE LAPPLICATION WIDI SOIT PR-INSTALLE (SELON LA CONFIGURATION DE VOTRE
SYSTME). LES SYSTMES AYANT LA FONCTION INTEL WIDI PR-INSTALLE AFFICHENT UN ICNE WIDI SUR
LEUR BUREAU WINDOWS. SI CETTE ICNE NEST PAS AFFICHE, LA FONCTIONNALIT INTEL WIDI SERA
INSTALLE DS QUE VOUS EXCUTEREZ LE LOGICIEL CLICKME.
LA FONCTIONNALIT INTEL WIDI NE PEUT FONCTIONNER QUAVEC UNE CARTE DE RSEAU LOCAL SANS FIL INTEL.
VEUILLEZ PRENDRE NOTE QUE LE CONTENU SCURIS NE PEUT TRE AFFICH AVEC INTEL WIDI 2.0. LES
DOCUMENTS AVEC PROTECTION DE LECTURE DE CONTENU, COMME LES DISQUES BLU-RAY ET LES FILMS
SUR DVD, NE SONT PAS PRIS EN CHARGE PAR WIDI.
EN MODE DAFFICHAGE WIDI, IL EST POSSIBLE QUE VOUS OBSERVIEZ UN LGER DCALAGE LORSQUE VOUS
DPLACEZ LA SOURIS OU QUE VOUS TAPEZ DU TEXTE.
LA PREMIRE FOIS QUE VOUS UTILISEZ LAFFICHAGE WIDI, LA RSOLUTION DAFFICHAGE CHOISIE PAR DFAUT
EST 1280X720. SI VOUS DSIREZ CHOISIR UNE AUTRE RSOLUTION, ALLEZ PANNEAU DE CONFIGURATION ->
PROPRITS DAFFICHAGE, SOUS LONGLET PARAMTRES. LORSQUE VOUS CHOISISSEZ UNE RSOLUTION,
ELLE CONTINUE SAPPLIQUER PAR DFAUT JUSQU CE QUE VOUS CHOISISSIEZ UNE AUTRE RSOLUTION.
SEUL LE LECTEUR WINDOWS MEDIA PEUT TRE UTILIS POUR LIRE DES DOCUMENTS AVEC WIDI 2.0.
AVANT DUTILISER LA FONCTIONNALIT INTEL WIDI, VRIFIEZ SI LE COMMUTATEUR DE RSEAU SANS FIL EST
LA POSITION DE MARCHE.
Assurez-vous quun adaptateur daffichage appropri est connect au tlviseur sur lequel vous dsirez utiliser
laffichage WiDi et allumez le tlviseur.
2
3
4
Si vous navez pas encore activ le commutateur de communication sans fil sur votre portable, faites-le maintenant.
Cliquez sur licne WiDi de votre bureau Windows ou sur le raccourci correspondant de votre menu Dmarrer.
Limage de lordinateur est automatiquement affiche sur le tlviseur grand cran.
Aprs le jumelage initial entre lordinateur portable et un adaptateur daffichage compatible, vous pouvez
paramtrer ladaptateur pour quil soit automatiquement connect par dfaut. Dans le futur, vous naurez
plus qu ouvrir lapplication pour connecter les deux appareils.
143 -
Si vous dsirez des informations dtailles sur lutilisation et le dpannage de la fonctionnalit WiDi,
cliquez sur licne WiDi, puis cliquez sur le bouton [Aide] dans le coin suprieur droit afin douvrir
le fichier daide daffichage sans fil.
144 -
Index
propos de ce guide 7
Adaptateur auto/avion 33
Alimentation
adaptateur auto/avion 33
adaptateur secteur 33
gestion 41
mise hors tension 44
mise sous tension 36
panne 75
problmes 77
sources 33
Auto-diagnostic de mise sous tension 36, 82
problmes 76, 77
recharge 46
remplacement 48
remplacement hors tension 48
remplacement sous tension 48
Batterie au lithium 45
BIOS
guide 38
utilitaire de configuration 38
Bluetooth
informations supplmentaires 140
Bouton dalimentation/veille/reprise 12
Bouton Soutien 13
Batterie 45
alarme 47
augmentation de la dure de vie 100
batterie au lithium 45
batterie/entre c.c. 19
compartiment 18
conservation de lnergie 41
court-circuite 47
dfectueuse 76
entretien 99
puise 76
faible 47
mode veille 47
niveau de charge 20
144
Clavier 12, 22
pav numrique 22
problmes 73
touches de curseur 23
touches de fonction 23
touches Windows 23
Click Me! 39
Cliquer 26
Commande 25
Commandes et connecteurs 11
Connexion des adaptateurs dalimentation 33
Conventions utilises dans ce guide 7
Coordonnes pour contacter Fujitsu 8
F
FDU 40, 93
Fente de dispositif antivol 16
Fonction de veille prolonge 42
activation/dsactivation 43
G
Garantie 9
Gestion de lalimentation 41
Gestion de lalimentation dans Windows 43
Glisser 28
Grilles de ventilation 18
Haut-parleurs incorpors 71
Haut-parleurs stro 13
Dpannage 68
DIMM 59
Disque dur
problmes 72, 73
voyant daccs 21
Double-cliquer 27
L
Lecteur de DVD
problmes 71, 72
Lecteur multimdia
alimentation par batterie 55
chargement 51
entretien 101
panneau de configuration 55
programmes 51, 54
retrait 54
utilisation 55
Lecteur optique 16, 50
bouton douverture 16
graveur de DVD multiformat modulaire 50
ouverture du plateau 54
Logiciels pr-installs
Adobe Acrobat Reader 109
guides dutilisation 109
Loquet de lcran 11
E
cran 12, 34
fermeture 35
luminosit 35
ouverture 34
problmes 79, 80
rglage 35
Emplacement du commutateur Marche/
Arrt de la carte rseau local sans fil 13
Enregistrement 40
Entre de ligne 64
tiquette de configuration 103
145
M
Mmoire
capacit 61
compartiment 17, 60
installation 59
module de mmoire additionnelle 59
problmes 74
retrait 61
Messages derreurs 82
Microphone 12
Microphone numrique 12
Mode ECO 24
Mode sommeil (veille) 41
SDRAM 17, 59
Secteur
adaptateur 33
adaptateurs de fiches 99
Sortie de ligne 64
Souris
problmes 73
R
Redmarrage 43
Rglage du volume 31
Remplacement hors tension 48
Remplacement sous tension 48
146
Spcifications 103
alimentation 107
audio 105
clavier 107
dimensions et poids 108
environnement dexploitation 108
mmoire 104
microprocesseur 104
options de mmoire de masse 105
puce 104
vido 104
U
USB 16, 64, 74
problmes 74
Utilitaire de mise jour des pilotes
Fujitsu Driver Update 40, 93
V
Verr dfil 21
Verr maj 21
Verr num 21
T
Tableau de voyants dtat 13, 19
Touche de fonction
F10 24
F3 24
F4 24
F6 24
F7 24
F8 24, 31
F9 24, 31
Fn 24
Touches de curseur 23
Touches Windows 23
touche application 23
touches dmarrer 23
147