Professional Documents
Culture Documents
Flow Switch PDF
Flow Switch PDF
The SPDT contact mechanism makes or breaks an electric circuit when flow
starts or stops. The FQS flow switch can be used for any fluid compatible with
copper alloy materials, which are the parts of the switch which come into con-
tact with the fluid.
The paddle consists of three segments that can be removed or trimmed and
fixed to the switch for use in pipes from 1 to 6 in diameter. The standard pad-
dles are made of copper alloy. Stainless steel paddles are also available.
2005.12.13 M.D.
Model Standard
Ambient temperature: -25C to 80C BENEFITS
Fluid temperature: 5 to 80C
Voltage (V) 125V 250V Ambient humidity: FQS-U30G - 80%RH simple mounting and wiring
AC AC FQS-W30G - 95%RH
Currrent (A)
(1)
6 paddle (material: strainless steel) is available
fast and easy to adjust to
Flow Full
Switches Type FQS
Load Amp. 3.5 2.5 upon request different pipe sizes
CHARACTERISTICS
Locked Rotor Amp. 21 15 water-proof version available if
Non-Inductive Amp. 15 15 required
installation in vertical or
horizontal position possible
FLOW AMOUNT - FLOW VELOCITY CHARACTERISTICS
CE and UL approval
1.1
1" Pipe 2" Pipe
1.0 SPDT contact system
3" Pipe
0.9
0.8
Velocity (m/sec)
0.7
0.6
4" Pipe APPLICATIONS
0.5
Q : Flow Amount (liter/min.) chilled water applications for
0.4
5" Pipe V : Velocity (m/sec.) air-conditioning systems
0.3 d : Pipe I.D. (mm)
6" Pipe
0.2 water ow control for heat pumps
0.1 Q= d2/4 x V x 6 x 10-2 (liter/min.)
hot-water supply systems
0 50 100 150 200 250 300 350
Flow Rate (L/min)
re-sprinkler systems
REFRIGERATION AND
AIR CONDITIONING
Q : Flow rate (L/min)
d2
V : Velocity (m/sec) Q= V 6 10 -2 (L/min)
4
2005.12.13 M.D. 2005.12.13 M.D. 2005.12.13
Flow Switches Type FQS Flow Switches Type FQS Flow Switches Type FQS
CHARACTERISTICS CHARACTERISTICS CHARACTERISTICS
PRESSURE DROP CHARACTERISTICS
These charts show fluid pressure drop caused by 1, 2 and 3 paddles that are used for 1, 2 and 3 pipes.
1" Pipe 2" Pipe 3" Pipe
700 1400
1" Paddle
2" Paddle
150 600 1200
1" Paddle 2" Paddle
500 1000
300 600
50 200 400
100 200
FQS_D_2a
FQS_D_1a
0 0.05 0.1 0.15 0.2 0.25 0 0.05 0.1 0.15 0.2 0.25 0 0.05 0.1 0.15 0.2 0.25
Pressure Drop (bar) Pressure Drop (bar) Pressure Drop (bar)
DIMENSIONS
DDIMENSIONS
IMENSIONS
FQS-U30G FQS-W30G
(117)
29 50 64 38 47 70
CE mark label
CE mark label
98.5
98.5
Conduit Gland
JIS F 8801 C-15C 12 1.2 Hex.36
Hex.36
12 1.2
Earth Mark
1.5
1.5
59
59
Unit: mm Unit: mm
INSTALLATION INSTRUCTIONS
1. The switch should be screwed into a pipe to a depth of 12.0 1.2mm. Liquid ow direction should be in accordance with
an arrow mark on the switch body.
2. Install the switch to a pipe where there can be a straight section of pipe with a length of at least ve times the pipe diameter
before the switch in the upper-stream. (This is in order to avoid the risk of incorrect switching which can arise from
turbulent ow.)
3. The switch (FQS) is supplied with the paddle consisting of 3 segments for pipe sizes ranging from 1 to 3 and set at the
2006.02.22
minimum ow rate unless otherwise specied. 2006.02.22
Danfoss Saginomiya Sp. z o.o. can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss
Saginomiya Sp. z o.o. reserves the right to alter its products without notice. This also applies to products already on order, provided that such
alteration can be made without subsequential changes being necessary in specications already agreed. All trademarks in this material are
property of the respective companies. Danfoss Saginomiya and the Danfoss Saginomiya logotype are trademarks of Danfoss Saginomiya
Sp. z o.o. All rights reserved.
PLRCA.PB.GK0.A1.02 July 2006