Professional Documents
Culture Documents
Assuming the client is capable of operating with Nv2 (correct hardware, correct
encryption key and ROS version), which setting(s) for 'wireless-protocol' should
be enabled on the client so that the client can auto-detect the protocol used b
y the AP and still stay connected with 802.11a or Nv2 : (select all that apply)
A. nv2-nstreme-802.11
B. any
C. Nv2
D. unspecified
6. Wireless Security Profile, Management Protection Key is for:
A. Frame Protection on any Device
B. Frame Protection only on RouterOS Devices
C. Frame Protection on RouterOS Devices and any other devices with Frame Protect
ion Support
7. You have a single AP for all clients to connect to. Which of the following wi
ll cause the clients to NOT be able to communicate with each other directly? (Ch
oose all that apply)
A. Uncheck "Default Forwarding" box in the wireless configuration
B. Uncheck both "Default Forwarding" and "Default Authenticate", add entries in
the access-list and enable only "Authentication"
C. Uncheck "Default Authenticate" in the wireless configuration
D. Uncheck both "Default Forwarding" and "Default Authenticate", add entries in
the access-list that enables both "Authentication" and "Forwarding"
8. Which EAP authentication methods can be used if the RouterOS acts as a client
?
A. EAP-TLS
B. EAP-MD5
C. EAP-TTLS
D. none
9. When several Virtual AP Interfaces are configured, you can add them to a brid
ge and apply layer 2 filter rules between them.
10. In the screenshot, why are two of the three 'Tx/Rx Signal Strength ChX' boxe
s empty?
A. Nv2 is not configured correctly
B. The CCQ is too low.
C. The radio is not configured to use 802.11n.
D. The signal strength is too low or too high
11. Access Point configuration is configured to "Management Protection=allowed"
and a Management Protection Key is set.
Which clients can connect to the AP (Choose the most universal answer)?
A. Any wireless client
B. Mikrotik Client with Management Protection=required
C. Mikrotik Client with Management Protection=allowed
D. Any Mikrotik Client
12. With what mode set wireless interface can be added as bridge port:
A. WDS
B. station
C. station-WDS
D. ap-bridge
13. Can you establish wds connection between 2 RouterBOARDs running wlan interfa
ces in ap-bridge mode on the same frequency and with the same SSID, dynamic wds
and nstreme enabled? FALSE
14. what changes if #WDS slave# wireless mode is set
A. Connect to an SSID as a client in slave mode
B. Enables WDS on AP
C. Adapts to Master WDS frequency
15. Wireless access point is required for customers. Which RouterBoards can be u
sed for it?
A. RB493 with level 4 licence
B. RB411 with level 3 licence
C. RB450G with level 5 licence
D. RB433 with level 4 licence
16. A station can connect to AP if they both use different country regulation se
ttings, but the frequency chosen is allowed in both countries TRUE
17. If the router's wireless interface is in 'station' mode and it is not able t
o connect to the access point in the same band with the same SSID and using the
same security profile, the possible reason for that could be (mark all answers t
hat are correct):
A. the station has "wmm-support=disabled", but the AP has " wmm-support=enabled"
B. the station has setting "scan-list=default" and the APs frequency is not
with in the default range
C. The station has different frequency setting from that of the AP
D. one of the wireless tools, e.g., scanner or snooper, is still running
18. You have a PtP Wireless link that keeps failing. Which of the following may
help determine the cause?
A. Last IP
B. Framing Limit
C. Tx/Rx Frames
D. Tx/Rx Hardware Frames
E. Tx/Rx CCQ
19. Picture shows signal,
A. 802.11a 20mhz channel. width.
B. Microwave oven.
C. 802.11n 20/40ht below 5180 MHz.
D. 802.11n 20/40ht above 5180 MHz.
E. 802.11a 5 MHZ channel width.
20. Country Regulation allows us to use up to 20dBm EiRP. We have a 10 dBi anten
na, total connector loss is 1 dB, pigtail loss is 2 dB, there are no other losse
s.
What should we set as the transmit power in the Wireless tab to conform to regul
ations ?
A. 7 dBm
B. 13 dBm
C. 33 dBm
21. In order to use dynamic keys in your security profile for an AP, you MUST se
t up the dhcp server to provide the dynamic keys. FALSE
22. What can be done to the client side setup in order to increase the receive s
ignal strength/SNR when connecting to an access point without increasing power o
utput of router?
A. use a higher sensitivity wireless card
B. limit the maximum allowed data rate
C. use a higher transmit power wireless card
D. use the nstreme protocol in the wireless system
E. use shorter antenna cable
23. WPA 2 Pre-Shared Key (PSK) is enabled on AP, all your clients have to use th
e same PSK. Only Virtual AP could be used to allow clients to connect with a dif
ferent PSK.
24. The 'access-list' of an AP is for:
A. Limiting transfer speed from RouterOS clients
B. Managing connectivity based on specific MAC, signal strength, Time, Frequency
C. Limiting transfer speed from non-RouterOS clients
D. Limiting transfer speed to RouterOS clients
E. Managing connectivity based on specific MAC, signal strength, Time, Private P
SK
25. Which WDS wireless modes are compatible with one other:
A. Dynamic mode with Static mode
B. Static-mesh mode with Dynamic mode
C. Static-mesh mode with Dynamic-mesh mode
D. Static mode with Dynamic-mesh mode
E. Static mode with Static-mesh mode
F. Dynamic mode with Dynamic-mesh mode