Professional Documents
Culture Documents
Technical Data
Digital Angle DWM 40 L
Measuring PROFESSIONAL
Device
Article number 0 601 096 603
Assembly
Inserting/Replacing the
Battery (see figure B)
Use only alkali-manganese or recharge-
able batteries.
To open the battery lid 7, slide the lid in
the direction of the arrow tip and fold it
up. Insert the batteries. Pay attention
that the polarity is correct, according to
the representation on the inside of the
battery lid.
After inserting the batteries and clos-
ing the battery lid 7, the measuring tool
is automatically switched on. For the
checking of the display, all indicator
elements appear for approx. 20 sec-
onds. Afterwards, the current angle is
displayed.
When the battery indicator b appears
in the display for the first time, meas-
urements are still possible for approx.
1 – 2 hours.
When the battery indicator b blinks,
the batteries must be replaced. Meas-
urements are no longer possible.
Always replace all batteries at the
same time. Only use batteries from one
brand and with the identical capacity.
f Remove the batteries from the
measuring tool when not using
it for extended periods. When
storing for extended periods, the
batteries can corrode and dis-
charge themselves.
Operation
Initial Operation
Note: Protect the measuring tool
against moisture and direct sun irradia-
tion.
Operating Instructions
Note: Keep the supporting surfaces
and contact edges 14 of the measuring
tool clean. Protect the measuring tool
against impact and shock. Debris par-
ticles or deformation can lead to faulty
measurements.
Projecting/Transferring Angles
(see figure D)
Position the measuring tool with the
fold-out leg or with the base leg against
the workpiece. Adjust the required
angle with the other leg and project the
angle onto the workpiece.
When directly projecting a measured
angle onto a workpiece, pay attention
that the fold-out leg and the base leg
are not moved in relation to each other
and that the “HOLD” mode is not
switched on.
Measuring with Leg Extension
(see figure G–J)
The leg extension 4 (accessory) ena-
bles the measuring of angles when the
contact surface is shorter than the fold-
out leg 1.
Attach the leg extension 4 (see “Attach-
ing the Leg Extension”). Position the
base leg 6 and the leg extension plane
against or on the edges to be meas-
ured.
The reading of the angle w between
base leg and fold-out leg is indicated in
the display. The required angle v
between base leg and leg extension is
calculated as follows:
v = 180° – w
Examples for measuring with leg exten-
sion are shown in figures G to J on the
fold-out page.
Maintenance and
Service
Maintenance and Cleaning
For safe and proper working, always
keep the measuring tool clean.
Do not immerse the measuring tool into
water or other fluids.
Wipe off debris using a moist and soft
cloth. Do not use any cleaning agents
or solvents.
When the measuring tool is exposed to
rain for an extended period, its function
may be impaired. However, after com-
pletely drying off, the measuring tool is
ready for operation. No calibration is
required.
Spare Parts
Battery lid 7 . . . . . . . . . 1 609 203 928
End cap 13 . . . . . . . . . 1 609 203 770
Joint cover 5 . . . . . . . . 1 609 203 927
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service: . +44 (0) 18 95 / 83 87 82
✆ Advice line:
. . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax:. . . . . . . +44 (0) 18 95 / 83 87 89
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
✆ Service: . . . +353 (0)1 / 4 66 67 00
Fax:. . . . . . . . . +353 (0)1 / 4 66 68 88
Disposal
Measuring tools, accessories and pack-
aging should be sorted for environmen-
tal-friendly recycling.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service:
. . . . . . . . . . +44 (0) 18 95 / 83 87 82
✆ Advice line:
. . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax:. . . . . . . +44 (0) 18 95 / 83 87 89
Description du
fonctionnement
Un travail optimal avec
cet appareil de mesure
n’est possible que si
vous lisez complète-
ment les instructions
d’utilisation et les instructions de
travail et que vous respectiez stric-
tement les indications qui y sont
mentionnées. GARDER PRECIEU-
SEMENT CES INSTRUCTIONS DE
SECURITE.
Dépliez le volet sur lequel l’appareil de
mesure est représenté de manière gra-
phique. Laissez le volet déplié pendant
la lecture de la présente notice d’utili-
sation.
Eléments de l’appareil
La numérotation des éléments de
l’appareil se réfère à la représentation
de l’appareil de mesure sur la page
graphique.
1 Branche mobile
2 Voyant pour écran
3 Numéro de série
4 Prolongement de la branche*
5 Couverture du joint
6 Branche de base
7 Couvercle du compartiment à piles
8 Touche « HOLD »
9 Interrupteur Marche/Arrêt
« ON/OFF »
10 Afficheur
11 Bulle d’air pour orientation
horizontale
12 Bulle d’air pour orientation
verticale
13 Capuchon de protection
14 Bord de guidage
15 Etui de protection*
Eléments d’affichage
a Valeur de mesure
b Indicateur de charge de la pile
c Affichage « HOLD »
*Les accessoires décrits ou montrés ne
sont pas compris dans l’emballage
standard.