Professional Documents
Culture Documents
1. A Wi-Fi router that connects to the Internet (should have the SSID and password of this router)
2. A gateway
3. An android phone
note: If the SEG-X1 gateway does not flash green, follow the guide in the Gateway manual or mobile app.
1. Power on your gateway and wait for the LED light to start flashing purple (This means the gateway is
in AP mode)
2. Connect to phone to the Wi-Fi of the router
note: If the gateway LED light is not flashing in purple, please follow the gateway manual to reset it to
factory settings.
Step 5. In the APP Permission interface, turn on all the access and tap "Confirm"
Step 6. Open the app (You could also open the "SmartOWON" app in the home screen)
note: You can also download the app from Huawei market and Baidu application market.
Step 2. To register an account, you can register using your regular email address or mobile number.
note: If you are an old user, please register a new account first. Login to your account, restore your
gateway's Wi-Fi and restart the configuration wizard (to restore the gateway's Wi-Fi, simply press the reset
button ONCE while holding the wifi button of the gateway)
Step 3. If you use your mobile phone number to register, the “Area Code” will be displayed automatically on
the right side of the account name. Please confirm whether the identified area code is correct. If not, you
can modify it manually.
Step 4. After the registration is successful, you can log in to use the account.
note: If you use your mobile phone number to register, the “Area Code” will be displayed automatically on
the right side of the account name. Please confirm whether the identified area code is correct. If not, you
can modify it manually.
Step 2. You may tap “Forgot Password” and follow the instructions to reset your password if needed
Step 3. If you need other login methods, you can select the “Other options” at the bottom left of the login
interface and log in according to the guidelines
Chapter 5 Add new devices
note: No devices will be shown on the inteface during your initial login.
Step 1. After logging in to the account, tap the "+" sign in the upper left corner
note: If you have bound the gateway to your account, but your router has been replaced, you can first
restore the gateway's Wi-Fi and configure the gatway to the new router (To restore gateway's Wi-Fi and
restart the configuration wizard (to restore the gateway's Wi-Fi, simply press the reset button ONCE while
holding the wifi button of the gateway)
Step 7. Tap the "Start" button, wait for the SEG-X3/SEG-X3N gateway to flash blue, and the application
software prompts that the binding is successful. Now you can find the gateway in the gateway list
note:If you have multiple gateways that are powered on at the same time, and they are all used for the first
time, you have to configure the gateway one by one. You may tap "refresh" to find more gateways (if any)
Step 8. If your gateway is flashing blue, you can also bind to your account by tapping the "others" -> "scan
gateway's QR code" -> OK
Step 1. Be sure that your phone is connected to the same router connected by the SEG-X1
Step 2. After logging in to the account, tap the "+" sign in the upper left corner
Step 3. Select SEG-X1
Step 5. Scan and obtain the QR code on the SEG-X1 and click "OK" to bind
Step 6. If your gateway is not flashing green, please choose other method for binding
note: If you cannot find the gateway that you want to bind in the list, please confirm that the mobile phone
Wi-Fi and the gateway are connected to the same router, then click the "Refresh" button to find more
gateways (if any)
1. After the gateway configuration is successfully, the gatway will be displayed on the gateway list
interface
2. Select the desired gateway that you want for the system
You can find the Home, Energy, Comfort, light, Security, Video, Setting interfaces in the menu bar.
Step 2. Tap "Edit" and select a scene to enter the scene editing interface
Step 3. Tap the "+" button to select devices and corresponding state (Arm/Disarm or On/off)
Step 4. Select the desired device in the device list and tap "Done" button
Step 5. After selecting the devices, "save" the scene and execute it in the scene interface
Energy measuring devices such as smartplug, power clamp, etc. will be shown in this interface. The App
interface will be as below:
6.4 Comfort interface
1. Thermostats, air conditioners, temperature and humidity sensors, etc. will be shown in this interface.
The App interface will be as below:
1. Power relays, light LED bulbs, etc. will be shown on this interface.
2. Users may control the lighting devices as well as adjust brightness and color temperature in this
interface. The App interface will be as below:
1. All security sensors including door/windows sensors, PIR (motion sensors), smoke detector sensors,
etc. will be shown on this interface. The App interface will be as below:
2. In a armed state, an alarm will be sent to your mobile phone if the sensor is triggered
5. In a disarmed state, only emergency sensors (Smoke detector, CO detector, Gas detector, SOS etc)
will trigger the siren
6.7 Video interface
1. For first time users, please enter the account name and follow the pop-up window to add the camera
2. If there is no pop-up window shown in the screen, please tap the "add" in the upper left corner to add
the camera
note: For old users, after you bind the gateway with your new account, a window will ask you to enter the
old username of the camera when you enter the video interface
1. To set the linkage between control device (e.g. power relay, smart plug, etc.) and sensors
1. To change password
2. To upgrade APP
3. To view help
Switch to the Settings interface, then tap "Add new devices", then the system will allow devices to be
added. The App interface will be as below:
note: for this step, your could also do the following: press the “Z" button of the gateway for three seconds
until the blue light turns solid. Then it will allow devices to be added into the network for the next 60
seconds.
Please follow the user guide of the corresponding devices to set the devices to joining status. Then the
devices will add into this system automatically while the system is in adding new devices mode ( while the
gateway's blue LED light is solid).
Below 7.2 section will show you details of how to add some typical devices.
Step 1: Plug the smart plug WSP403 into an outlet and turn it on
note: If the LED of WSP403 is solid on (either green or red), please refer to the user guide to return it to
factory settings.
note: for this step, you could also press the "Z" button of the gateway for around three seconds until the
blue LED is solid on.
Then the WSP403 will add into the system automatically. If added successfully, the LED indicator of the
WSP403 will turn to solid, in the meanwhile, the App interface will be as below:
note: If the LED does not flash twice after you power it on, please refer to the user guide to return it to
factory settings.
note: For this step, you could also press the "Z" button of the gateway for around three seconds until the
blue LED is solid on.tThen the LED622 will add into the system automatically. If added successfully, the
LED622 will flash once and the App interface will be as below:
Step 3: Press the side button of the sensor, and the device will flash green
Then the DWS302 will add into the system automatically. If added successfully, the LED indicator of the
DSW302 will become solid for a while then off. The App interface will be like below:
note: this SLC603 is designed to work with a LED bulb such as LED622.
note: For this step, you could also press the "Z" button of the gateway for around three seconds until the
blue LED is solid on.
Step 3: Press the reset button once
Then the SLC603 will be added into the system automatically. If added successfully, the LED indicator of
the reset button will flash green for three times, but this deivice will not be shown in the App.
Regarding how to bind with LED622, please see section "8.1 LED bulb detailed functions—>bind with
SLC603 dimmer switch"
Step 1: Plug the AC201 Split AC control into an outlet facing your air conditioner that you would like to pair
and control
note: If the LED of AC201 is solid yellow, please refer to the user guide to return it to factory settings.
note: For this step, you could also press the "Z" button of the gateway for around three seconds until the
blue LED is on.
Then the AC201 will be added to the system automatically. If added successfully, the LED indicator of the
AC201 will turn solid yellow, in the meanwhile, the App interface will be as below:
Step 3: Pair with your air conditioner
1. Tap "pair"
4. Tap "SCAN"
5. Then the AC201 will be in the process of searching for the paring code, press
"STOP" right after you hear a beep from the air conditioner
6. Tap "Verify"
7. Press "ok" when you see a prompt asking you to verify if this code will work with
your air coditioner or not
8. Then you will enter the below interface, set system, power, temperature, on/off, etc.
to see if the air conditioner responds or not
note: If the LED indicator in the camera is not flahsing, please reset it to factory settings follow the gateway
user guide.
Step 2: For first time users, please enter the username (mobile phone number or email) and password
Step 3: Tap "next" (if no window is pop up, please tap the "add" in the upper left corner
Step 4: Choose your Wi-Fi and enter the password (tap the "refresh" button if your Wi-Fi is not found
Step 5: After the camera is connected to the network, select the corresponding device to bind
Step 6: You will be able to see the video after the binding is successful
Please note:
2. To add the second camera, tap "edit" > "+" and follow the guide
Tap the on or off, the left “plug” icon will be on (white) and off (grey) respectively, also for this smart plug, it
will show you the instant power and energy consumption.
Step 4. Finish
On/off schedule
Step 4. Finish
Step 1. Tap the grey "—" icon to enable this schedule item
Step 2. Tap the orange "—" to disable this schedule item
Step 3. Finish
Delete a schedule item
Step 4. Finish
Tap the "on" or "off" icon, the left “light” icon will be on (white) and off (grey) respectively.
Step 1. Tap the ">" icon will enter dimmer and color temperature setting screen
Step 2. Adjust brightness and color temperature
Change name
Step 4. Finish
On/off schedule
Step 4. Finish
Step 1. Tap the grey "—" icon to enable this schedule item
Step 3. Finish
Delete a schedule item
Step 4. Finish
Please follow the below steps to bind with SLC603 in the mobile app:
Step 3. During the process of identifying, the LED622 will start flashing
Step 4. Press and hold the reset button of the SLC603 for three seconds until the LED indicator flashes
green three times, the SLC603 will bind with the LED622, once succesful, the LED622 will stop flashing,
then you will able to use the SLC603 to control the LED622.
Step 4. Finish
Arm and disarm schedule
Step 1. Tap the grey "—" icon to enable this schedule item
Step 1. Tap the ">" icon to enter the schedule adjustment interface
Step 2. Set and save
Step 3. Finish
Sensor history
note: This setting is in the setting interface next to the gateway list
Step 3: Tap "Check Update" to see if there is an available update app and gateway firmware, if so, tap the
corresponding link to download and update
8.4.2 Upgrade gateway firmware