Professional Documents
Culture Documents
Please Note:
Insert the batteries following the markings inside the battery
compartment.
Immediately dispose of any leaking batteries.
Dispose old batteries as per manufacturers instruction.
HELPLINE 0845-6021348
Testing the Controller for Operation
Once the batteries have been inserted, press any of the buttons
to ensure that the Red LED flashes; this confirms correct
installation of the batteries. If for any reason there is no response
from the controller then check the battery installation or the
condition of the batteries. If during its life the easytip 4 operating
range diminishes then the batteries may need replacing. Your
easytip 4 controller has an inbuilt special feature which allows
you to change batteries without losing pre-programmed
information, however, do not touch any of the controls during
battery exchange or pre-programmed date will be lost.
In the back pages of this manual you will find the 3-number codes
which allow you to set-up your easytip 4 controller.
Before starting, make a note of all the codes for the appliances
you wish to control with your easytip 4 so that they are easily to
hand while you are doing the programming.
HELPLINE 0845-6021348
Quick Set-up Reference (TV Programming)
Example
HELPLINE 0845-6021348
Please re-check the 3-number code in the manual or
restart Item 5 completing the programming within the
allotted time.
VCR Programming
AUX Programming
The Aux. button allows you to setup additional TV’s, Sat, VCR so
that 2 devices can be controlled from the one controller.
Depending on the type of equipment to be controlled by the
easytip 4, use the relevant instructions above. You will find the
correct 3-number code from the appropriate section (TV, VCR,
Sat) at the back of this manual.
HELPLINE 0845-6021348
Programming the easytip 4 in Automatic mode
If the listed codes failed to operate the TV, or if your TV was not
included in the manual, it is possible to enter into automatic
search mode. Automatic mode allows the controller to search and
test every code in the manual. As there are many codes for the
controller to select and test, automatic mode will take several
minutes to perform.
HELPLINE 0845-6021348
Changing the direction of the search when in
automatic mode:
First insert a video cassette into your VCR and push the play key
on your VCR, then follow the TV example above, however,
instead of using the Power ON / OFF key, please use the STOP
key.
ATTENTION!
Code search begins from the last code number found in the
previous search. When the end of the code list is reached the
LED will flash 3 times. The search is then repeated from the
beginning. Please be patient, there may be many codes for your
TV to search and test before finding the correct one. At the AUX
level there is no possibility to run automatic mode!
Step 1 Select the Item you wish to check (TV, VCR, Sat)
Step 2 Press and hold the chosen button on your easytip 4
controller until the LED flashes twice
Step 3 Within the next 5 second input the code 002, this alerts
the controller to provide its programmed code settings.
Step 4 After entering the code the LED will Flash twice
confirming your choice. Immediately after, press the
numeric keys 1,2,or 3 on the keypad.
HELPLINE 0845-6021348
Step 5 Each successive number will induce the LED to flash its
internal code number, for example, if after pressing key
1 on the keypad the LED flashes 3 times, then the initial
part of the 3 digit code is 3. By immediately pressing
key 2 on the keypad the LED flash according to the next
number of the code, the same applies to key 3. If no
flash occurs, then the code number is 0 (zero). Finally
you will have the full code. There is no need to hurry, if
you misscount the number of flashes then you can
press the key once more. Provided you keep pressing
the 1, 2 & 3 keys within a 5 second period the remote
will continue to flash the code number. If no buttons are
pressed for 5 seconds then the remote returns to
normal function.
TV
VCR
Satellite
AUX
Button 1 = Brightness
Button 2 = Color
Button 3 = Contrast
Button 4 = Treble
Button 5 = Bass
Button 6 = Balance
Step 2 Now you can operate the function by using the VOL Up
and VOL Down keys. After adjusting, the remote will
return to normal function within 5 seconds.
HELPLINE 0845-6021348
Understanding your easytip 4
Channel Buttons
HELPLINE 0845-6021348
Channels 10~99
Function keys explained
HELPLINE 0845-6021348
X TV: Current Teletext site. Choose a
teletext site then push this key, after that
the TV will return to normal viewing
whilst seaching teletext in background.
When the teletext site is found the TV
set will turn automatically to the teletext
screen.
SAT: Switch between SAT and TV
channels
HELPLINE 0845-6021348