You are on page 1of 4

HENCO VISION

RADIATOR

SANITARY

Your Connection to Perfection

HENCO VISION: fast and reliablefor installers with Vision


The bench-mark product among push-fit systems.
} } }

Fast and easy to install Highest quality and durabilty For sanitary and heating installations

PVDF, high quality synthetic material with a unique combination of properties. The composition of the push-t tting shows that Henco Vision is the result of intensive product development. All the parts are made with the highest precision and of the best materials. The tting is made of PVDF, a high quality synthetic material with a unique combination of properties:
} } } }

Resistant to high pressure and temperatures Excellent mechanical strength Flexibility of up to 10 Approved for use in drinking water systems

Composition
A B C D E F

A B C D E F

Vision window PVDF body with two EPDM O-rings Stainless steel grab ring Stainless steel support ring PVDF tapered split ring PVDF end cap with EPDM O-ring and demounting slots

Assembling Vision
With Vision there are three simple steps in making a reliable joint:
1. 2. 3. CUT - Ensure the pipe is cut at 90. The Henco guillotine cutter has a handy cradle to support the pipe whilst cutting. CALIBRATE - Calibrate the pipe with the Henco Kalispeed. Slide the calibrator right into the pipe, rotate clockwise

until a continuous bevel is cut to both the inner and outer edges of the pipe. Important, removal all swarth. PUSH - After removing the protection cap push the pipe all the way into the tting. Use the Vision window to ensure the pipe is fully home.
CUT

2
90

CALIBRATE

PUSH

Demounting Vision
Henco Vision can be demounted very quickly. Even O-rings can easily be changed; for example when you remark a leak during pressure testing, probably caused by bad calibration.
1 2

Unscrew the sleeve.

Pull the pipe, together with the sleeve, out of the tting body.

3a

3b

If the pipe is long enough, cut it behind the sleeve.

If the pipe cannot be shortened, open the sleeve with the HencoVision key.

Cut the grab ring and remove it together with the other elements on the pipe.

CALIBRATE!

Take a replacement set (new sleeve and set of 0-rings) and change the damaged O-rings carefully without damaging the tting body and the new O-rings.

Screw the new sleeve clockwise onto the tting body. Push the calibrated pipe into the tting. (See ) There we are!

ADVANTAGES
Henco Vision is supplied with a protection cap to avoid dirt getting into the tting. Vision quickly demountable.

The outer O-ring and Vision window cover forms a seal to prevent the ingress of dirt, water, additives or concrete into the tting.

Vision easily reassembled.

Two internal O-rings form a seal on the inside of the pipe.

Vision pleasing to the eye.

Vision has a unique support ring providing extra strength and stability to the grab ring. Safety guaranteed!

Vision easily installed where space is restricted.

Visions innovative design incorporates a unique tapered split ring. In addition to providing support to the stainless steel rings, this ground breaking design prevents expansion of the pipe within the tting, eliminating pull-out failure.

95C/10 bar

Vision ttings withstand up to a 10 ection.

Vision visibly better.

Vision is available in diameters of 16, 20 and 26mm.

In line with our history of innovation, and after years of ground-breaking research and intensive development, Henco are proud to introduce Vision A further addition to Hencos comprehensive range. This condence is underlined by the 10 year Henco system guarantee.

Your Connection to Perfection

Henco nv Toekomstlaan 27 - B-2200 Herentals Tel. +32 14 285 660 Fax +32 14 21 87 12 www.hencovision.be

IMA3611.3-07UK

Imaprorealisations.com

You might also like