Professional Documents
Culture Documents
Pgina 1 de 13
Desarmado y Armado
Nmero de medio -RENR2535-12
i03742880
Assembly Procedure
Table 1 Required Tools Tool Part Number A B 1P-7405 FT-0841 Part Description (3/8 inch NC Lifting Eye) Spring Compressor Qty 2 1
Illustration 1
g00440250
Illustration 2
g00440249
2. Install plate (30) , 44 bolts (31) , and the washers on ring (29) . The weight of plate (30) is 110 kg (242.5 lb). Tighten bolts (31) to a torque of 500 50 Nm (368.8 36.9 lb ft).
Illustration 3
g00440247
NOTICE
Failure to follow the recommended procedure or the specified tooling that is required for the procedure could result in damage to components. To avoid component damage, follow the recommended procedure using the recommended tools.
3. Turn over the assembly. Install two dampers (27) , the 15 friction discs, and 14 plates (28) on the service brake assembly. Note: When the two dampers, the 15 friction discs, and the 14 plates are installed, begin with a damper. Next, install a friction disc. Then, install a plate. Continue installing the friction discs and the plates. After the last friction disc is installed, install the other damper.
Illustration 4
g00440245
4. Install eight studs (26) on ring (29) . Tighten studs (26) to a torque of 100 15 Nm (73.8 11.1 lb ft).
Illustration 5
g00466478
5. Install four plugs (23) and the four O-rings on anchor (3) . 6. Install 21 studs (25) and 47 studs (24) on anchor (3) . Tighten studs (24) to a torque of 230 30 Nm (169.6 22.1 lb ft). Tighten studs (25) to a torque of 400 40 Nm (295.0 29.5 lb ft).
Illustration 6
g00466472
Illustration 7
g00466473
7. Install three O-ring seals (19) , (20) , and (21) on anchor (3) . 8. Install 12 studs (22) on anchor (3) .
Illustration 8
g00466471
9. Install 46 springs (17) and 42 inner springs (18) on anchor (3) . Note: There are four springs (17) at location (X) that do not have inner springs (18) . Refer to the identification marks on the springs for installation purposes.
Illustration 9
g00439623
10. Install guide spring (6) and guide (7) in piston (13) . Use Tooling (B) to compress guide spring (6) . Install the pin. Repeat this step for the remaining three pins, guides (7) , and guide springs (6) .
Illustration 10
g00439583
Illustration 11
g00439495
12. Install two seal rings (14) . Install two seal rings (15) on housing (12) .
NOTICE
Failure to follow the recommended procedure or the specified tooling that is required for the procedure could result in damage to components. To avoid component damage, follow the recommended procedure using the recommended tools.
Note: During installation, proper orientation of the seal rings is important. Improper installation of the seal rings can cause the seals to leak. Note: The yellow side (C) of inside seal ring (D) must face out.
g00467514
g00467518
Illustration 14
g00467520
Illustration 15
g00467526
14. Install housing (12) on the service brake assembly. Install 12 nuts (11) on housing (12) . Tighten nuts (11) by one turn at a time in order to draw the housing downward. After 12 nuts (11) have bottomed out, tighten the nuts to a torque of 271 24 Nm (200 18 lb ft). The nuts should be tightened in a crisscross pattern.
Illustration 16
g00466468
15. Install two ring seals (9) . Install two ring seals (10) on piston (5) . Note: During installation, proper orientation of the seal rings is important. Improper installation of the seal rings can cause the seals to leak. Note: The yellow side (C) of inside seal ring (D) must face out.
g00467514
g00467518
Illustration 19
g00466445
16. Use Tool (A) and a suitable lifting device to install piston (5) . The weight of piston (5) is 83 kg (183.0 lb).
Illustration 20
g00466443
17. Press down piston (5) . Install four pins (8) in four guides (7) .
Illustration 21
g00466441
18. Install two 3/8 inch - 16 NC forcing screws in piston (5) . Evenly tighten forcing screws in order to compress the guide springs. 19. Remove the four pins from four guides (7) . 20. Remove the forcing screws from piston (5) .
Illustration 22
g00466436
21. Turn over anchor (3) . Use a suitable lifting device to install anchor (3) on the ring. Anchor (3) weighs approximately 206 kg (454.2 lb).
Illustration 23
g00466170
22. Install eight nuts (4) on anchor (3) . 23. Tighten eight nuts (4) by one turn at a time in order to draw anchor (3) downward. After all eight nuts (4) have bottomed out, tighten the nuts to a torque of 270 25 Nm (199.1 18.4 lb ft). Tighten the nuts in a crisscross pattern. 24. Install 55 bolts (2) and the 55 washers which hold anchor (3) in place.
Illustration 24
g00466169
25. Turn over the service brake assembly. Install twelve bolts (1) and the washers that are identified in the picture on the service brake assembly. End By: Install the front service and parking brakes that are on the right or the left. Refer to Disassembly and Assembly, "Service and Parking Brake (Rear) - Install" for the correct procedure.
Copyright 1993 - 2011 Caterpillar Inc. Todos los derechos reservados. Red privada para licenciados del SIS.