Professional Documents
Culture Documents
SRD2900
If you need additional assistance for set-up or operating after reading owners manual, please call TOLL FREE : 1- 800 - 968-3429 Please read before using this equipment.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION: INSIDE, NEAR THE DECK MECHANISM. FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR VITER LES CHOC LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
EN
1L25
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6. Attachments - Do not use attachments not recommended by the video product manufacturer as they may cause hazards. 7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories - Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power Sources - This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE
GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMP POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) ANTENNA LEAD WIRE
S2898A
14. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges. 15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product. 18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or damaged in any way. f. When the video product exhibits a distinct change in performance this indicates a need for service. 20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards. 21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 22. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
EN
1L25
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
Remote control Two AA batteries A/V cables RF cable
(NA206CD)
WPZ0901TM002
VCR
: refers to playback of video cassette tapes.
DVD
: refers to playback of DVD video discs.
CD
: refers to playback of audio CDs.
MP3
: refers to playback of MP3 discs.
EN
1L25
TABLE OF CONTENTS
I LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3 ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4 I FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 I PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 I OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . . . 9 DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12 LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 12 I VIDEO/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . 13 I HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . . 14 SETTING THE CH3/CH4 SWITCH . . . . . . . . . . . . . . . . . . . 14 CONNECTING TO A TV . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 CONNECTING TO A TV THAT HAS AN S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS . . . . . . . . . . . . 14 CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 CONNECTING TO A DOLBY DIGITAL DECODER OR DTS DECODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 CONNECTING TO AN ANALOG AUDIO . . . . . . . . . . . . . . 16 I SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 17 TO CHANGE THE ON-SCREEN LANGUAGE . . . . . . . . . . 18 CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 I PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 NORMAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 19 SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 I RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 20 VIEWING AND RECORDING THE SAME PROGRAM . . . 20 VIEWING AND RECORDING DIEFERENT PROGRAM . . 20 OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . . . . . . 20 TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 21 I SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 22 MTS (Multi-Channel Television Sound) SYSTEM. . . . . . . . . 22 AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 REAL TIME TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . 23 I PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 PLAYING A DVD VIDEO OR AN AUDIO CD . . . . . . . . . . 23 USING THE DVD MENUS . . . . . . . . . . . . . . . . . . . . . . . . . 23 USING THE TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . 24 PAUSING PLAYBACK OR DISPLAYING A STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 RESUMING PLAYBACK FROM THE POINT WHERE PLAYBACK STOPPED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 STEPPING THROUGH FRAMES . . . . . . . . . . . . . . . . . . . . 24 FAST FORWARD/REVERSE . . . . . . . . . . . . . . . . . . . . . . . . 25 SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 STARTING FROM A DESIRED TRACK . . . . . . . . . . . . . . . 25 PLAYING FROM A DESIRED TITLE OR A CHAPTER . . . 25 STARTING FROM A DESIRED TIME COUNT. . . . . . . . . . 26 MARKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 RANDOM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 PROGRAM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ZOOM PLAYBACK (enlargement on-screen) . . . . . . . . . . . . 28 PLAYING AN MP3 DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 CHANGING THE ON-SCREEN DISPLAY DURING MP3 DISC PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 PLAYING A DESIRED TRACK FROM AN MP3 DISC . . . 30 PLAYING AN MP3 DISC RANDOMLY . . . . . . . . . . . . . . . 30 PLAYING AN MP3 DISC IN A PROGRAM. . . . . . . . . . . . . 30 SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 CHANGING THE AUDIO LANGUAGE OR SOUND MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 CHANGING THE SUBTITLE LANGUAGE . . . . . . . . . . . . 32 CHANGING THE CAMERA ANGLE (Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 33 BLACK LEVEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . 33 TruSurround SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 CHANGING THE SETUP ITEMS . . . . . . . . . . . . . . . . . . . 34 LANGUAGE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 DISPLAY SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 LANGUAGE CODE LIST . . . . . . . . . . . . . . . . . . . . . . . . . . 38 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 39 HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . 40 DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
I I I I
INDICE
I CONTROLES DEL FUNCIONAMIENETO Y SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 I CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 I CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 DVD/VCR A CONEXIN DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 AJUSTANDO EL CONMUTADOR CH3/CH4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 CONECTANDO A UN TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE S-VDEO o TOMAS DE ENTRADA DE VDEO COMPONENTE . . . 46 CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT . 46 CONECTANDO A UN DESCODIFICADOR DIGITAL DOLBY O DESCODIFICADOR DTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 CONECTANDO A UN AUDIO ANALGICO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 I PREPARACIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 PREPARACIN DE CANAL AUTOMTICA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 PREPARACIN DE RELOJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 I REPRODUCCIN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
EN
1L25
FEATURES
DVD Mode
Dolby Digital sound On-screen display
This player can handle Dolby Digital surround sound with 5.1 channels when connected to a Dolby Digital decoder.
Still/fast/slow/step playback
Information about the current operation can be displayed on the TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.
DTS (Digital Theater System)
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in random order.
Program playback for audio CD and MP3
You can program the order of tracks to play them in any desired order.
DVD menus in a desired language
You can display DVD menus in the desired language, if available on the DVD.
Screen saver/Auto power-off functions
You can enjoy 5.1 channel surround system developed by the Digital Theater System Co. which reproduces the original sound as truthfully as possible. Search Chapter search: Search for a chapter designated by user is possible. Title search: Search for a title designated by user is possible. Track search: Search for a track designated by user is possible. Time search: Search for a time designated by user is possible.
Repeat
The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program has been activated for 30 minutes, the player is automatically turned off.
Subtitles in a desired language
Chapter:
You can select the desired language for the subtitle display, if that language is available on the disc.
Selecting a camera angle
You can select the desired camera angle, if the disc contains sequences recorded from different angles.
Choices for audio language and sound mode
You can select the desired audio language and sound mode, if different languages and modes are available on the disc.
Parental lock
Repeated playback of the chapter of the disc being played is possible. Title: Repeated playback of the title of the disc being played is possible. Track: Repeated playback of the track of the disc being played is possible. Disc (audio CD): Repeated playback of the entire disc being (MP3) played is possible. A-B: Playback of the section between A and B (designated by user) is possible. Album: Repeated playback of the album of the MP3 disc being played is possible.
Zoom
A 2 and 4 magnified screen can be displayed. A part designated by user can be called back.
You can set the control level to limit playback of discs which may not be suitable for children.
Automatic detection of discs
This player automatically detects if the loaded disc is DVD, audio CD or MP3 on disc.
Playing an MP3 disc
User can resume playback from the part at which the play was stopped even if the power is turned off.
SRS TruSurround
You can search for the desired title, chapter, and track with the Number buttons during playback or in stop mode.
You can enjoy a stereophonic virtual space on your existing stereo system. Component Video Out Jacks Jacks located on the back of the DVD/VCR COMBINATION UNITS are used to send high-quality video to a TV via Component Video In Jacks.
Dimmer
This unit employs TruSurround system of SRS Labs, Inc. as virtual technology. TruSurround and the symbol are trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS Labs, Inc.
EN
1L25
VCR Mode
Hardware specifications
Auto Head Cleaner 4 Head HiFi Stereo Bilingual on-screen menu display selectable in
Playback
S-VHS Quasi Playback (SQPB)
er tuner with direct station call (A cable converter box may be necessary to view scrambled cable channels.)
Recording
1 Year, 7 events (including Daily and Weekly Timer
Automatic functions
Auto power on system
Recording)
OTR (One Touch Recording)
PRECAUTIONS
INSTALLATION LOCATION
For safety and optimum performance of your DVD/VCR COMBINATION UNITS: Install the DVD/VCR COMBINATION UNITS in a horizontal and stable position. Do not place anything directly on top of the DVD/VCR COMBINATION UNITS. Do not place the DVD/VCR COMBINATION UNITS directly on top of the TV. Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the DVD/VCR COMBINATION UNITS. Avoid locations subject to strong vibration or strong magnetic fields.
EN
1L25
DISC TYPES
[DVD] Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If a function you selected does not run as desired, refer to the manual accompanying the disc.
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
Audio CD
12 cm Sound 8 cm (singles)
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as PAL or SECAM. Some discs include region codes as shown below.
[AUDIO CD] Data on an audio CD is divided into sections called tracks, each of which is given a track number.
world, and a disc encoded in a specific region format can only be played back on DVD/VCR COMBINATION UNITS with the same region code. The following discs cannot be played back on this DVD/VCR COMBINATION UNITS.
DVD with region codes other than 1 or ALL. DVD-ROM DVD-RAM (Never attempt to play back,
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
otherwise a malfunction may result.) CD-ROM VSD CDV (Only plays back the audio part.) CD-G (Only plays back the sound.) CD-R/CD-RW (Only plays back discs on which audio CD or MP3 are recorded.) CD-I (Never attempt to play back, otherwise a malfunction may result.) SACD
Photo CD
[MP3] Data on an MP3 is divided into sections called "albums", and then into subsections called "tracks", each of which is given an album or track number.
Example
Album 1
Track 1 Track 2 Track 3 Track 4
Album 2
Track 1 Track 2
(Never attempt to play back, otherwise a malfunction may result.) Any other discs without compatibility indications
EN
1L25
VIDEO DVD OPERATION OUTPUT VCR OPERATION CHANNEL TIMER SET VCR/TV OPEN/CLOSE STOP SKIP/REV PLAY FWD/SKIP STOP/EJECT REW PLAY F.FWD REC/OTR CST.IN L AUDIO R
25
23 24 56 22
7. 8.
21 20
19 18
17 16
15
REMOTE CONTROL
27 28
1 4 7 2 5 8 0
DISPLAY DVD POWER SPEED AUDIO
26
13 11 14 12 10
3
SKIP/CH.
55
VCR/TV
9.
29
6 9
+100
SLOW
54 53
10.
+ 10
VCR PAUSE
30 31 32 33
RECORD PLAY STOP
52 51 49
12.
50
11.
34 35 37 39 41
MENU
48
ENTER
13. 14.
36 38 40
47
RETURN
SETUP
TITLE
SEARCH MODE
46 45 43 44 42
MODE
ZOOM
CLEAR/ C.RESET
A-B
1. Disc loading tray 2. DVD OUTPUT Light (Green) [page 13] This light appears when the DVD output mode is selected. You can only watch DVDs when the green DVD OUTPUT Light is on. To make the green DVD OUTPUT light come on, press the DVD button on the remote control or the OUTPUT button on the front panel. 3. VCR OUTPUT Light (Green) [page 13] This light appears when the VCR output mode is selected. You can only watch tapes when the green VCR OUTPUT light is on. To make the green VCR OUTPUT light come on, press the VCR button on the remote control or the OUTPUT button on the front panel. 4. CASSETTE COMPARTMENT 5. REC/OTR Light [page 20] Lights up during recording. 6. TIMER SET Light [page 20] The Timer light on current VCR does not glow during One Touch Timer Recording(OTR). It flashes if the TIMER SET button is pressed for a timer recording, but there is no tape in the VCR. It flashes when all timer recordings or One-Touch Recordings are
15. 16.
17.
18.
finished. POWER Button [page 17] Press to turn the power on and off. POWER Light Lights up when the power is on. VIDEO In Jack Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source (laser disc player, camcorder, etc.) here. AUDIO In Jacks Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here. TIMER SET Button [page 21] Press to put the VCR into standby mode for a timer recording. CST IN Light [page 19] Lights up when a cassette is in the VCR. VCR/TV Light [page 17] Lights up when the VCR is in the VCR position, and goes off when it is in the TV position. CHANNEL Buttons [page 17] In VCR mode, press to change TV channels on the VCR; press to adjust the tracking during normal or slow motion playback; press to remove vertical jitter in a Still picture. REC/OTR Button (VCR) [page 20] Press once to start recording. Press 2 times or more and the unit will record in 1/2 hour increments. F.FWD Button (VCR) [page 17] Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search). When setting program (For example:setting clock or timer program), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numbers during channel preset. PLAY Button (VCR) [page 17] Press to begin playback. Press to enter digits when setting program (For example: setting clock or timer program). Press to advance settings during on screen menu. REW Button (VCR) [page 18] Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search). Press to cancel a setting of timer program when in on screen menu. Press to correct digits when setting program (For example: setting clock or timer program). Press to add or delete channel numbers during channel preset. EN
1L25
19. STOP/EJECT Button (VCR) [page 21] GEJECT Button Press to remove the tape from the VCR. G STOP Button Press to stop the tape motion. Press to enter digits when setting program (For example:setting clock or timer program). Press to select the setting modes from the on screen menu. 20. OUTPUT Button [page 13] Press to select DVD mode or VCR mode. G You can switch the output mode either by pressing the OUTPUT button on the front panel, or by pressing the DVD or the VCR button on the remote control. However, if you press the OUTPUT button on the front panel first, you need to re-select the corresponding mode by pressing the DVD or the VCR button on the remote control. 21. FWD/SKIP Button (DVD) [page 25] Plays back from the beginning of the next chapter or track. Hold down for fast forward playback. 22. PLAY Button (DVD) [page 23] Press to begin playback. 23. SKIP/REV Button (DVD) [page 25] Plays back from the beginning of the current chapter or track. Hold down for fast reverse playback. 24. STOP Button (DVD) [page 23] Stops operation of the disc. 25. OPEN/CLOSE Button [page 23] Press to insert discs into or remove them from the tray. 26. Display, Remote Sensor Window 27. SPEED Button [page 20] Press to select the VCRs recording speed (SP or SLP) 28. POWER Button Press to turn the power on and off. 29. Number Buttons G DVD mode [page 25] Press to directly select a Track (Audio CD) for playback. Press to program Tracks (Audio CD) for playback. G VCR mode [page 17] Press to select TV channels on the VCR. To select channels, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 then 6. +100 Button: If you want to select channels 100 and above, press this button first, then press the last two digits. For example, to select channel 125, press +100 button first, then press 2 and 5. 30. DISPLAY Button G DVD mode [page 29] Press to access or remove the display screen during DVD or Audio CD playback. G VCR mode [page 22] Press to access or remove the VCRs on-screen status display. 31. DVD Button [page 13] Press to select DVD mode for the remote control. G You can switch the output mode either by pressing the OUTPUT button on the front panel, or by pressing the DVD or the VCR button on the remote control. However, if you press the OUTPUT button on the front panel first, you need to re-select the corresponding mode by pressing the DVD or the VCR button on the remote control.
32. h (REV) Button G DVD mode Press to view the DVD picture in fast reverse motion or to reverse playback of an Audio CD. G VCR mode Press to rewind the tape, or to view the picture rapidly in reverse during the playback mode (Rewind Search). Press to cancel a setting of timer program. Press to correct digits when setting program (For example: setting clock or timer program). Press to add or delete channel numbers during channel preset. 33. STOP Button G DVD mode Press to stop the disc motion. G VCR mode Press to stop the tape motion. Press to enter digits when setting program (For example: setting clock or timer program). Press to select the setting modes from the on screen menu. 34. RECORD Button Press once to start recording. 35. MENU Button G DVD mode [page 23] Press to display the menu of the Disc. G VCR mode [page 17] Press to access the VCR menu. 36. TITLE Button[page 24] 37. SETUP Button [page 34] Press to enter the setup mode. 38. ZOOM Button [page 28] Enlarges part of a DVD-reproduced image. 39. MODE Button [pages 26] Activates program playback or random playback mode when playing CDs or MP3. Sets Black level or SRS TruSurround. 40. SUBTITLE Button [page 32] Press to select the desired subtitle language. 41. ANGLE Button [page 32] Press to change the camera angle to see the sequence being played back from a different angle. 42. REPEAT Button [page 27] Repeats playback of the current disc, title, chapter or track. 43. A-B REPEAT Button [page 27] Repeats playback of a selected section. 44. SEARCH MODE Button G DVD mode [page 25] Press to access or remove the Search display, which allows you to go directly to a specific Title/Chapter/Track/Time. G VCR mode [page 19] Press to perform a Time Search or an Index Search. 45. CLEAR/C.RESET Button G DVD mode [page 26] Press to reset the setting. G VCR mode [page 18] Press to reset the counter. Press to exit from the MENU screen. 46. RETURN Button Returns to the previous operation in the DVD MODE. 47. Arrow Buttons Use when making settings while watching the display on a TV screen. EN
1L25
10
48. ENTER Button Press to accept a setting. 49. g (FWD) Button G DVD mode Press to fast forward the Disc. Press the PAUSE button, then press this button to begin slow motion playback. Press this button repeatedly to change the forward speed of slow motion. G VCR mode Press to rapidly advance the tape, or view the picture rapidly in forward during playback (Forward Search). When setting program (For example: setting clock or timer program), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numbers during channel preset. 50. PLAY Button G DVD mode Press to begin playback. G VCR mode Press to begin playback. Press to enter digits when setting program (For example: setting clock or timer program). Press to select the setting modes from the on screen menu. 51. VCR Button [page 13] Press to select VCR mode for the remote control. G You can switch the OUTPUT mode either by pressing the OUTPUT button on the front panel, or by pressing the DVD or the VCR button on the remote control. However, if you press the OUTPUT button on the front panel first, you need to reselect the corresponding mode by pressing the DVD or the VCR button on the remote control. 52. PAUSE Button G DVD mode [page 24] Press to pause Disc playback. Press repeatedly to advance the DVD picture step by step (or one frame at a time). G VCR mode [page 19] While recording, press to temporarily stop the recording (pause). Press a second time to resume normal recording. You can not pause a One-Touch Recording. Or, press during tape playback to freeze the picture. Press to advance the picture one frame at a time during still mode.
53. SLOW Button [page 19] During tape playback, press to view the video tape in slow motion. Press again to resume normal playback. This button does not affect DVD playback. 54. VCR/TV Button [page 21] Use to select VCR or TV position. If the VCR/TV light appears on the front of the VCR, it is in VCR position (in either VCR or DVD mode). If the VCR/TV light doesnt appear on the front of the VCR, it is in TV position. G VCR Position When the green VCR OUTPUT light appears on the front of the VCR, use the VCR to watch a tape, watch a TV program while recording it, or watch a TV broadcast using the CHANNEL or the Number buttons to change channels at the VCR. When the green DVD OUTPUT light appears on the front of the DVD, use the DVD to view Disc playback or menus. G TV Position Use to watch TV (changing channels at the TV) or watch one program while recording another. 55. SKIP/CH. Buttons G DVD mode Press to skip Chapters or Tracks. G VCR mode Press to change TV channels on the VCR. 56. AUDIO Button [page 31] Press to select a desired audio language or sound mode.
Notes To use the remote control to operate the DVD/VCR COMBINATION UNITS and its features, press the DVD button on the remote control before pressing other DVD buttons. Verify that the green DVD OUTPUT Light is on. To use the remote control to operate the VCR and its features, press the VCR button on the remote control before pressing other VCR buttons. Verify that the green VCR OUTPUT Light is on.
REAR VIEW
57
58
DVD/VCR OUT
59
60
COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
67 66 65
57. AC Power Cord
64 63
62 61
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.
EN
1L25
Connect the supplied audio cables here and to the Audio In jacks of a television or other audio equipment.
60. COMPONENT VIDEO OUT Jacks (DVD Video only)
Connect optional component video cables here and to the component Video In jacks of a television. 61. COAXIAL Jack Connect an optional coaxial digital audio cable here and to the Coaxial Digital Audio In jack of a decoder or audio receiver. 62. S-VIDEO OUT Jack (DVD Video only) Connect an optional S-Video cable here and to the S-Video In jack of a television. 63. DVD/VCR VIDEO OUT Jack Connect the yellow video cable (supplied) here
Connect a cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.) here. 65. CH3/CH4 Switch Set to channel 3 or 4 to use your TV with your VCR. 66. ANT-IN (Antenna In) Jack Connect your antenna, Cable Box, or Direct Broadcast System. 67. ANT-OUT (Antenna Out) Jack Use the supplied RF cable to connect this jack to the ANTENNA IN Jack on your TV. Notes The S-VIDEO OUT jack, COAXIAL jack, and COMPONENT VIDEO OUT jacks are only useful in DVD mode.
DISPLAY
Lit when the A-B repeat function is on. Lit when the repeat function is on. Lights up when a DVD is inserted into the tray.
Lights up when the inserted disc comes to a pause. Lit when the inserted disc is being played back.
Displays how long the current title or track has been playing. When a chapter or track is switched, the number of the new title, chapter or track is displayed.
12
EN
1L25
VCR/DVD SWITCHING
Since this product is both a VCR and DVD player, it is necessary to select the correct output mode.
SWITCHING TO VCR MODE
Press the VCR button on the remote control. (Verify that the VCR OUTPUT Light is lit.)
Notes Pressing only the OUTPUT button on the front panel does not switch the mode of the remote control. You always need to select the correct mode on the remote control too.
POWER
VIDEO DVD OPERATION OUTPUT VCR OPERATION CHANNEL TIMER SET VCR/TV OPEN/CLOSE STOP SKIP/REV PLAY FWD/SKIP STOP/EJECT REW PLAY F.FWD REC/OTR CST.IN L AUDIO R
POWER SPEED
AUDIO
1 4 7
2 5 8 0
3
SKIP/CH.
6
VCR/TV
9
+100
SLOW
VD OPERATION
OUTPUT
DVD OUTPUT Light DVD button VCR OUTPUT Light VCR button VCR OPERATIO
+ 10
VCR PAUSE
DISPLAY
DVD
PLAY
STOP RECORD
MENU
LAY
FWD/SKIP
STOP/EJECT REW
SETUP TITLE MODE ZOOM
ENTER RETURN
SEARCH MODE CLEAR/ C.RESET
OUTPUT button
A-B
13
EN
1L25
HOOKUPS
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the AC outlet. 2. Disconnect the antenna or cable from the TV. 3. Connect the antenna or cable to the ANT-IN jack of the DVD/VCR COMBINATION UNITS. 4. Connect the DVD/VCR COMBINATION UNITS to the TV using the RF cable. 5. Plug the AC power cords of the DVD/VCR COMBINATION UNITS and TV into the AC outlets.
[VHF/UHF combination antenna] [Indoor antenna] [Back of the DVD/VCR] RF cable (supplied)
UHF/VHF
CH3 CH4
IN
OR
ANT - IN
OR
ANT - OUT
Note to CATV system installer This reminder is provided to call the CATV system installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.
CONNECTING TO A TV
IN DVD/VCR OUT COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
To ANT. IN of TV To VIDEO INPUT jack To Right (red) and Left (white) To AUDIO INPUT jacks To VIDEO OUT jack To AUDIO OUT jacks
[Fig. 1]
Notes Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.
IN ANT - IN L AUDO
COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
To Right (red) and Left (white) To AUDIO INPUT jacks To AUDIO OUT jacks To S-VIDEO INPUT jack To S-VIDEO OUT jack
[Fig. 2]
EN
1L25
14
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality pictures. Note The component video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION UNITS. Therefore, in order to use the VCR features or view TV channels at the DVD/VCR COMBINATION UNITS, you still need to either connect the RF cable to the ANT-OUT jack of the DVD/VCR COMBINATION UNITS and the TVs Antenna In jack, or connect the yellow video cable as described earlier (Fig. 1). To connect the supplied RF cable, see DVD/VCR TO TV CONNECTION on page 14.
A/V-compatible or wide screen TV To COMPONENT VIDEO INPUT jacks To Right (red) and Left (white) AUDIO INPUT jacks To Right (red) and Left (white) AUDIO OUTPUT jacks
DVD/VCR OUT COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
[Fig. 3]
CONNECTING TO AN AMPLIFIER EQUIPPED WITH COAXIAL DIGITAL INPUT JACKS FOR DVD AUDIO ONLY
Use an audio coaxial digital cable (not included) for the audio connections. Connect to an amplifier equipped with coaxial digital input jacks.
DVD/VCR OUT
COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
Amplifier equipped with coaxial digital input jacks, MD deck, DAT deck, etc.
CH3 CH4
VIDEO
[Fig. 4]
Notes The audio source on a disc in the 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck. Be sure to turn off the power to all components in the system before connecting them together. Refer to the Owners Manuals for the components to be connected to the DVD/VCR COMBINATION UNITS. Set Dolby Digital and DTS to off for audio output in the setup mode. Playing a DVD disc using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 36 to set Dolby Digital and DTS to on)
Notes To listen to TV sound and VHS Hi-Fi stereo video tapes through the audio system, you must make the analog audio connection outlined in Fig.6 on page 16.
15
EN
1L25
CONNECTING TO A DOLBY DIGITAL DECODER OR DTS DECODER FOR DVD AUDIO ONLY
If using this DVD/VCR COMBINATION UNITS to play a DVD disc in 5.1 channel Dolby Digital surround, or DTS surround formats, the DVD/VCR COMBINATION UNITS outputs a Dolby Digital, or DTS data stream from its COAXIAL DIGITAL AUDIO OUT jack. By hooking the DVD/VCR COMBINATION UNITS up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic ambience with powerful and highquality surround sound of a professional standard such as can be heard in movie theaters. Use an audio coaxial digital cable (not included) for the audio connections.
DVD/VCR OUT
COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
[Fig. 5] Notes Be sure to turn off the power to all components in the system before connecting them together. Refer to the Owners Manuals for the components to be connected to the DVD/VCR COMBINATION UNITS. If the output is Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio output in the setup mode. If the output is DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode. Unless connected to a Dolby Digital decoder, or a DTS decoder, set Dolby Digital or DTS to off for audio output in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. DTS and DTS Digital Out are trademarks of Digital Theater Systems Inc. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Stereo system To Right (red) and Left (white) AUDIO OUT jacks
[Fig. 6]
Notes Be sure to turn off the power to all components in the system before connecting another component. Refer to the Owner's Manuals for stereo systems and any other components to be connected to the DVD/VCR COMBINATION UNITS. EN 16
1L25
SETUP
AUTOMATIC CHANNEL SET UP
VCR
The VCR can automatically program the tuner to scan only the channels which are available in your area. Channel memory programming is NOT needed when the VCR is connected to a cable box or a satellite box as in "DVD/VCR TO TV CONNECTION" on page 14. In this case, set the CH3/CH4 Switch (which is located on the back of your VCR) to either CH3 or CH4, whichever is not used for normal broadcasts in your area. Then set your TV to the same channel. The channel you want to record or view will be selected from the cable or the satellite box. Follow the steps below once. Repeat only if there is a power failure or if the VCR is unplugged for more than 30 seconds. (In these cases, the programmed channels are erased.) You must follow the steps below before attempting to play or record a video tape.
AUTO SET UP
check the cable connections. Press the F.FWD button once again and the VCR will begin preset again.
You can select the desired channel by using the CHANNEL buttons (o/p) or by directly pressing the Number buttons on the remote control. Note for using the Number buttons: When selecting cable channels which are higher than 99, press the +100 button first, then press the last two digits. You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).
3 Turn on the VCR by pressing the POWER button. Both the POWER and the VCR/TV light will come on.
TO PRESET THE CHANNELS AGAIN 1 Press the MENU button until the main menu
appears. (If you have already set the clock, you only have to press it once. If not, you have to press it twice).
rized channel.
17
EN
1L25
TO ADD/DELETE CHANNELS
When scanning, some channels may be skipped due to a weak signal. In such cases, you can add the channels to the VCR memory manually.
CLOCK SET UP
VCR
Set the clock accurately for proper automatic timer recording. We suggest that you use a TV or radio station as your time source.
Press the MENU button until the main menu appears. (If you have already set the clock, you only have to press it once. If not you have to press it twice). - MENU TIMER PROGRAMMING [OFF] AUTO REPEAT CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT [ON] TV STEREO SAP
4 Enter the desired channel number by pressing the PLAY or the STOP button.
Press the PLAY button or the STOP button repeatedly. Then, press the F.FWD button.
2) Set the day
Press the PLAY button or STOP repeatedly. Then, press the F.FWD button.
3) Set the year
Press the PLAY button or the STOP button repeatedly. Then, press the F.FWD button. The day of the week will appear automatically.
4) Set the hour
Press the PLAY button or the STOP button repeatedly. Then, press the F.FWD button.
5) Set the minute
Press the PLAY button or the STOP button repeatedly. Then, press the F.FWD button.
6) Set AM or PM
CLOCK SET MONTH DAY YEAR 03 / 18 MON 2002 HOUR MINUTE AM/PM 05 : 40 PM AM PM
18
EN
1L25
PLAYBACK FUNCTION
NORMAL PLAYBACK
VCR 1 Insert a prerecorded tape. The VCR will turn
on, and the VCR/TV Light and the CST IN Light comes on. If the safety tab has been removed,
SEARCH FUNCTIONS
VCR PICTURE SEARCH
If you want to skip or repeat a scene during playback, press the F.FWD or the REW button. Press it again and the VCR will now search at super high speed. (in the LP/SLP modes only).
(Digital Tracking function) when you start playback. To adjust the tracking manually, press the CHANNEL buttons (o/p) on the VCR. When a tape has reached the end, the VCR will automatically rewind the tape to the beginning, and eject the tape. S-VHS Quasi Playback (SQPB): This unit allows you to view a tape recorded in S-VHS format. (Noise lines may appear on the picture.)
INDEX SEARCH
The index signal is recorded on the tape automatically when a recording is started. If you want to view a recording at a specific start point, this can be done easily.
F.FWD button. If you want to go in the reverse direction, press the REW button. After index search, the VCR will play the tape automatically.
TIME SEARCH
This feature allows you to fast forward or rewind the tape for the desired length of time.
TIME SEARCH 2 : 50
F.FWD button.
If you want to go in the reverse direction, press the
REW button.
After time search, the VCR will play the tape auto-
matically.
EN
1L25
19
RECORDING FUNCTION
VCR
It may be UNLAWFUL to record copyrighted material without the consent of the copyright owner. Accidental Erasure Prevention To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the Record safety tab hole with cellophane tape.
Number buttons on the remote control or the CHANNEL buttons (o/p). (If you connected the VCR to a cable box or satellite box as in "DVD/VCR TO TV CONNECTION" on page 14, set the VCR to channel 3 or 4 i.e. the same channel as the CH3 or CH4 switch on the back of the VCR. Then, select the channel you want to record with the cable box or satellite box. In this case, you can ONLY record and view the SAME channel.) There is a tape with a safety tab in the VCR. The desired recording speed is selected in SP (standard play) or SLP (super long play) mode by pressing the SPEED button on the remote control.
Tape Speed Type of tape SP mode SLP mode T60 1 hour 3 hours Recording/Playback Time T120 2 hours 6 hours T160 2-2/3 hours 8 hours
OTR(7:30)
the tape, and switch to the DVD mode automatically as the TIMER SET light blinks. (If the DVD power is off, the VCR will switch to STANDBY status). When OTR is finished , the VCR turns off automatically. To use the VCR again, press the TIMER SET button on the VCR.
TIMER RECORDING
VCR
You may set the VCR to start recording while you are away. You can set seven programs to record on specific days, daily or weekly within a 1 year period.
If you have not yet set the clock, "CLOCK SET" appears. If so, follow the steps [3] and [4] in "CLOCK SET" section on page 18. Then, set the timer recording.
1 Insert a tape with its safety tab intact. 2 Press the MENU button. 3 Select "TIMER PROGRAMMING" by pressing the
PLAY or the STOP button. Then, press the F.FWD button. The set up screen is displayed.
TIMER PROGRAMMING PROG. 1234567 DATE START TIME END TIME CHANNEL REC SPEED
PAUSE button. After the VCR has been in Pause mode for 5 minutes, it will stop automatically to protect the tape and the video head from damage.
4 Set the timer. If you make mistakes, press the REW button repeatedly to go back to the item you want to correct.
If you press the REW button after step 7), all the
information youve just entered for that program number will be cleared.
PROGRAM NUMBER 4 DATE --/-START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - -
A program number which is not allocated flashes. Press the PLAY button or the STOP button repeatedly for the desired program number. Then, press the F.FWD button.
2) Set the frequency of the recording
Press the PLAY button or the STOP button to select the desired frequency from ONCE, DAILY, or WEEKLY recording. Then, press the F.FWD button.
EN
1L25
First, press the PLAY button or the STOP button for the month. Then, press the F.FWD button. Next, press the PLAY button or the STOP button for the day. Then, press the F.FWD button.
4) Set the start time
ONE TIME PROGRAM PROGRAM NUMBER 4 DATE --/-- -START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - -
First, press the PLAY button or the STOP button for the hour. Then, press the F.FWD button. Next, press the PLAY button or the STOP button for the minute. Then, press the F.FWD button. And then, press the PLAY button or the STOP button for AM or PM. Then, press the F.FWD button.
5) Set the end time
ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME - - : - - - END TIME - - : - - - CHANNEL -REC SPEED - -
Follow the same instructions as "Set the start time" to set the end time.
6) Set the channel number
ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME 07: 30 PM END TIME - - : - - - CHANNEL -REC SPEED - -
VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER SET light blinks. (If the DVD power is off, the VCR will switch to STANDBY status). If a tape is not in the VCR, or the tape does not have a safety tab, the TIMER SET light flashes and timer recording will not operate. Please insert a recordable tape. When all timer recordings are finished, the TIMER SET light will flash. To use the VCR again as usual, press the TIMER SET button to disable the flashing TIMER SET light, then press the VCR/TV button to select the VCR position. The VCR/TV light will appear. Press the VCR button to choose VCR or DVD mode, then continue with the other features as described in this manual. When timer recordings are set, the TIMER SET light will come on. To use the VCR as usual until the time for the recording, press the TIMER SET button so that the TIMER SET light disappears. Press the VCR/TV button to choose the VCR position. The VCR/TV light will come on. Press the VCR button to choose VCR or DVD modes, then continue with the other features as described in this manual.
Press the PLAY button or the STOP button repeatedly for the desired channel number. Then, press the F.FWD button.
ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME 07: 30 PM END TIME 08: 30 PM CHANNEL -REC SPEED - -
If you want to use the DVD player during a VCR timer recording or while the TIMER SET light is on or flashes.
You can use the DVD player while the TIMER SET light
If you connected the DVD/VCR to a cable box or satellite box as in "DVD/VCR TO TV CONNECTION" on page 14, set the DVD/VCR to channel 3 or 4 i.e. the same channel as the CH3 or CH4 switch on the back of the DVD/VCR. Then, select the channel you want to record with the cable box or satellite box. Leave the cable box or satellite box on for timer recording.
is on or flashes, or during a timer recording. Press the POWER button to turn on the VCR. Press the VCR/TV button to choose VCR position. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You dont have to set the TIMER off to use the DVD.
Press the PLAY button or the STOP button repeatedly for the desired tape speed. Then, press the F.FWD button.
ONE TIME PROGRAM PROGRAM NUMBER 4 DATE 05 /13 MON START TIME 07: 30 PM END TIME 08: 30 PM CHANNEL 16 REC SPEED SP SP SLP
TO CHECK, CORRECT, OR CANCEL AN AUTOMATIC TIMER PROGRAM 1 Turn the power on by pressing the POWER
button. (If the VCR is in TIMER STANDBY status, press the TIMER SET button instead of the POWER button.)
es to STANDBY status, and switches to DVD OUTPUT mode automatically. When DVD sits idle for more than thirty-five minutes, the DVD power will be turned off automatically. If you press the TIMER SET button under such condition, the VCR power will be turned off and switch to STANDBY status.
3 Select "TIMER PROGRAMMING" by pressing the PLAY or the STOP button. Then, the F.FWD button.
TO CLEAR A PROGRAM
Follow the steps from 2 to 3. Select the program number you want to clear, and then press the REW button.
TV screen.
Go to the digit you want to change by pressing the
F.FWD or the REW button. Then, enter correct numbers by pressing the PLAY or the STOP button. You may cancel the entire program by pressing the REW button while the program number flashes.
for more than 30 seconds, the clock setting and all 6 timer settings will be lost. 21
SPECIAL FEATURES
COPYING A VIDEO TAPE
VCR
You can make copies of video tapes made by friends or relatives for your enjoyment. Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. Connect the recording VCR (this unit), the playing VCR (another source) and your TV using the following diagram. You can use the AUDIO/VIDEO input jacks on the front panel of the VCR instead of using the jacks on the back.
[Recording VCR] (this unit)
DVD/VCR OUT IN ANT - IN L AUDO R ANT - OUT 3CH 4CH VIDEO R Cb DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT PCM / BITSTREAM OUT COAXIAL COMPONENT VIDEO OUT
RCA-type connectors. Standard audio cables are not recommended. You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs in place of the playing VCR.
TO MONITOR THE RECORDING 1 Turn on the TV and set the TV to channel 3 or 4. Now set the CH3/CH4 switch on the back of the
DVD /VCR to match the channel selected on the TV.
Cr
LEFT RIGHT
OUT IN VIDEO
AUDIO
ANT in
and sub audio, you must select the Recording mode to TV STEREO or SAP before you record a broadcast.
HiFi, HiFi will disappear from the TV screen and the VCR will automatically play in monaural. select "L1" position by pressing [0], [0], [1] on the remote control or the CHANNEL buttons (o/p). When you use the A/V input jacks on the front of the VCR, MTS RECORDING/MONITOR MODE select "L2" position by pressing [0], [0], [2] on the remote Display on the STEREO/SAP Type of Hi-Fi audio track Normal audio TV screen Selection broadcast (2-channel) track control or the CHANNEL buttons (o/p). L-channel R-channel Regular -Invalid-NoneNote (monaural audio) Mono Mono Mono L1 and L2 are found before the lowest memo-InvalidL Stereo STEREO R L+R broadcast rized channel. (Example: CH2) TV STEREO* Main audio Main audio Main audio SAP
4 Press the REC/OTR button on the recording VCR. 5 Begin playback of the tape in the playing
VCR. For best results during dubbing, use the VCRs front
panel controls whenever possible. The remote control might affect the playing VCRs operation. Always use video-quality shielded cables with 22
EN
1L25
AUTO REWIND
When a tape reaches the end during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the VCR will eject the tape. The VCR will not rewind the tape automatically during timer recording or One Touch Recording.
in hours, minutes, and seconds. (The displayed time will not change during blank portions of the tape.) The indication will appear when the tape is rewound further than 0:00:00 on the tape counter.
PLAYING A DISC
PLAYING A DVD VIDEO OR AN AUDIO CD
DVD Getting started
Turn on the power of the TV, amplifier and any other components which are connected to the DVD. (Select the correct audio input on your audio system to match what you wish to view: Coaxial Digital Audio for DVD and analog for TV, VHS Hi-Fi stereo video tapes.) Notes A prohibited icon may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.
If a disc is dirty or has scratches, the pictures may
CD
appear distorted and the playback operation may stop. In such cases, clean the disc and unplug the power cord and then plug it again before resuming playback.
With DVDs that use titles for playback program
signals, playback may start from the second title, or it may skip these titles.
During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a malfunction.
then start from the first chapter or track of the disc. You need to press the PLAY button only when the tray has been closed by pressing the OPEN/CLOSE button.
If your DVD has a title menu, it may appear on the
2 Select the desired title. Press the Arrow buttons (L/K/B/s) to change the
setting, and then press the ENTER button.
screen. In this case, refer to USING THE DVD MENUS in the next section, or USING THE TITLE MENU on page 24.
Press 'PLAY' to play from here. To play the beginning, press 'STOP' first and then 'PLAY'.
2 Select the desired title. Press the Arrow buttons (L/K/B/s) to select a
desired title, and then press the ENTER button.
Note
The contents of menus and corresponding menu
Note
The resume function can be reset by pressing the
operations may vary between discs. Refer to the manual accompanying the disc for details.
muted.
24
EN
1L25
FAST FORWARD/REVERSE
DVD CD
1 Press the g (FWD) or the h (REV) button during playback. For DVDs, pressing the g (FWD) or h (REV)
button cycles the playback speed in four steps. In the case of DVDs, the sound will mute. For audio CDs, the playback speed is fixed at 16.
REV Button x2 FWD Button x2
You can also press the SEARCH MODE button and use the Number buttons to enter the track number. When the track number is entered in the entry box, playback of the desired track will start automatically.
TR : 5
x8
x8
TRICKS WITH THE SKIP BUTTONS (H, G) If the SKIP button G is pressed during playback or while playback is paused, the current track will be skipped and the next track will start. If the SKIP button H is pressed once, the beginning of the current track will be located for replay. If the SKIP button H is pressed again within 2 seconds after playback begins, the previous track will be located.
x30
x30
x60
x60
SLOW MOTION
DVD
speed in three steps. Select the appropriate speed while referring to the speed indication on the screen.
FWD Button 1/16
1/8
1/2
title or chapter will start automatically. Notes If you didnt press 0 before entering the single digit number, you have to press ENTER to go to the desired title or the chapter.
Notes Slow playback is not available with audio CDs. Reverse slow motion is not available. Slow playback from a TITLE to other TITLE is not possible. 25
EN
1L25
MARKER
DVD
You can define the part to be called back.
CD
CHAPTER SEARCH:
title or chapter will start automatically. Notes Play back from a desired title or chapter is not available with some DVDs. If the title being played does not display the chapter number, that means the chapter search function is not available with that title. TRICKS WITH THE SKIP BUTTONS (H, G) If the SKIP button G is pressed during playback or while playback is paused, the current chapter will be skipped and the next chapter will start. If the SKIP button H is pressed once, the beginning of the current chapter will be located for replay. If the SKIP button H is pressed again within 2 seconds after playback begins, the previous chapter will be located.
Set the marker Using the Arrow buttons (s/ B), position the cursor on to the marker number shown as NOT SET. Press the ENTER button when the screen to be reviewed appears. The marked time will be displayed. Up to 5 points can be marked. Call back the marker Using the Arrow buttons (s/ B), position the cursor on to the marker number to be called back and press the ENTER button. Clear the marker Using the Arrow buttons (s/ B), position the cursor on to the marker number to be cleared and press the CLEAR/C.RESET button. To clear all markers, place the cursor on AC (All clear markers) and press the ENTER button.
30 seconds 12330 Notes For a DVD, Time Search in Title is effective. (But Time Search in Chapter is ineffective.) For a CD, Time Search in Track is effective. (But Time Search in the entire disc is ineffective.) Playback from a desired time count is not available with some discs or if the unit is in stop mode. If the wrong numbers are entered, press the CLEAR/C.RESET button and re-enter the correct numbers.
START : PLAY
EXIT : MODE
Note
Program playback is not available during random
playback.
26
EN
1L25
REPEAT
DVD CD
A-B REPEAT
DVD CD
For DVDs
A single title or chapter can be played back repeat-
edly.
Pressing the REPEAT button cycles the display on
selected.
No repeat playback.
The current chapter is played back repeatedly. The current title is played back repeatedly.
end point (B) of the desired section. The selected section will be
REPEAT [A-B]
repeatedly.
Pressing the REPEAT button cycles the display on
Notes
With DVDs, the A-B repeat section can be set only
No repeat playback.
REPEAT [TRACK]
The current track is played back repeatedly. The whole disc is played back repeatedly.
REPEAT [ALL]
DVD.
To cancel the A point which was set, press the
CLEAR/C.RESET button.
A-B repeat playback does not function when title,
chapter, or repeat (all) playback has been set. If the REPEAT button is pressed once during program/random playback, the current track will be played back repeatedly. If the REPEAT button is pressed again, the program/random playback will be performed repeatedly. Notes Repeat playback is not available with some discs. The REPEAT setting will be cleared when moving to an other title, chapter or track. Repeat playback does not function during A-B repeat playback. 27
EN
1L25
--
screen.
START: PLAY RANDOM: MODE DELETE: CLEAR EXIT: RETURN
02 05 07 04 10 14 06 15 21 08 20 28 10 25 35 12 30 42 11 34 49 16 40 58 18 45 63 01 03 _
button works as follows. Press the STOP button once and then press the PLAY button again. Playback will restart from the point where the STOP button was pressed. (Program continued)
steps to the right, 4 steps to the left, 4 steps to the top, and 4 steps to the bottom when times 2 zooming. The frames will move 6 steps when times 4 zooming.
The current position will be displayed on the right-
bottom of the screen. Press the ENTER button, and the display will disappear.
TO CLEAR THE PROGRAM 1 Press the STOP button twice, and the program will be cleared.
Notes
Adding programs is not possible during program
playback. You must stop the current playback before such operations can be carried out.
Press the CLEAR/C.RESET button to cancel a pro-
Note
Zooming function does not work while the disc
setting.
The programs will be cleared when you turn the
power off. 28
EN
1L25
screen, L appears to go to the next page. If there is a previous page, K appears on screen. To the left of L, the current page and the total number of pages are displayed.
The player can recognize 255 albums and tracks
altogether.
will be displayed when repeat play has been selected. T: Track repeat A: Album (folder) repeat D: Disc repeat
0:02:31 A TRACK11 TRACK12 TRACK13 TRACK14 TRACK15
[When a TRACK is selected] Starting from the selected track, the rest of the tracks will be played in order. [When an ALBUM is selected]
ALBUM01 +ALBUM11 +ALBUM12 +ALBUM13 +ALBUM14 +ALBUM15 SELECT: RETURN: / ENTER: START: PLAY
3 Press the DISPLAY button again, and the display screen disappears.
Press the Arrow button (B). The track selection screen shows up. Using the Arrow buttons (K/L), select the tracks to be played.
Choose FIRST PLAY, and the albums and tracks
be called back.
Albums can be played up to the 8th hierarchy.
29
EN
1L25
will be highlighted. In the case of RESUME OFF, the first track of the disc will be highlighted. Press the RETURN button, and the SEARCH menu disappears.
ALBUM NAME +ALBUM01 TRACK11 TRACK12 TRACK13 TRACK14 SELECT: RETURN: /
+ALBUM11 +ALBUM12 TRACK11 TRACK12 TRACK13 1/11 START: PLAY RANDOM: MODE
TRACK11
Notes
During play, a desired track can be searched for
directly. Just enter the track number with the Number buttons.
If the track number entered is not available, the dis-
ous hierarchy.
If the entire program cannot be displayed at once on
count.
Notes
Press the CLEAR/C.RESET button, and the last-
30
EN
1L25
SETTINGS
Notes Pressing the Audio button may not work on some DVDs with multiple audio languages (e.g. DVDs DVD CD which allow audio language setting on the disc menu). Operation varies between discs, so refer to the manual accompanying the disc. The DVD has a function which allows you to select the desired audio language and sound mode. The current audio language and sound mode will be displayed when you first press the AUDIO button.
For DVDs
the Audio button several times, the disc does not have an audio source in that language. The audio language resets to the one which was selected in the setup mode every time the power is 2 Press the AUDIO button repeatedly until you turned on or discs are replaced. If that language is see the language of your choice. not available on a disc, a language defined by the The audio language mode can be changed only if the disc will be selected. disc is recorded with a multiple language setting. The screen display will disappear after about 5 seconds. If you use DIGITAL AUDIO OUT jack, the sound mode of audio CDs can not be changed.
The current audio status will appear at the top.
AUDIO 1.ENG DolbyD 5.1CH 48k/3 AUDIO 2.FRE DolbyD 5.1CH 48k/3
HELLO
Bon jour
AUDIO L-CH
AUDIO R-CH
31
EN
1L25
selected language. The screen display will disappear after about 5 seconds. When SUBTITLE NOT AVAILABLE appears on screen, it means that no subtitle has been recorded.
are recorded in multiple languages on the DVD being played. The subtitle language cannot be changed if the subtitles are recorded in a single language on the DVD being played.
SUBTITLE 1.ENG/6
Subtitle 1
ent camera angles, the angle icon ( ) will appear at the top-right of the screen. You can change the camera angle when the icon appears on the screen.
The camera angle cannot be changed if the disc does
SUBTITLE 2.FRE/6
Subtitle 2
SUBTITLE OFF
OFF
Angle 1
language from SUBTITLE 1, SUBTITLE 2 and all the languages recorded. The current subtitle mode will be displayed when you first press the SUBTITLE button. Press the SUBTITLE button, and then press the Arrow button (s/ B) to set it to on or off.
ANGLE 2 / 8
Angle 2
ANGLE 8 / 8
Angle 8
HELLO
Bon jour
Notes Some discs allow subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.) If the desired language is not shown after pressing the SUBTITLE button several times, the disc does not have subtitles in that language. The subtitle language resets to the one which was selected in the setup mode, every time the power is turned on or discs are replaced. If that language is not available on a disc, a language defined by the disc is selected.
Notes The screen display will disappear after about 5 seconds. The current camera angle will be displayed when you first press the ANGLE button.
32
EN
1L25
You can check the information regarding the disc by pressing the DISPLAY button on the remote control.
TIME: Elapsed time of the current disk and remaining time of the current disc.
For DVDs
1 Press the DISPLAY button during playback.
CH 7/49 0:01:46 -0:03:27
3 Press the DISPLAY button or the RETURN butTIME: Elapsed time of the current chapter and remaining time of the current chapter.
BLACK LEVEL : ON
chapter.
C L0
BIT RATE indicator will appear. BIT RATE shows the quantity of information which is recorded on the DVD. Layer number (*) L0: Layer 0 is playing L1: Layer 1 is playing Current Repeat setting C: Chapter repeat T: Title repeat A B: A-B repeat
ON) OFF: The original picture which is recorded on the disc will be shown. Press the RETURN button to exit the display.
TruSurround SETTINGS
You can enjoy stereophonic sound system when you playback Dolby Digital and PCM 48 kHz sound.
4 Press the DISPLAY button or the RETURN button to exit the display.
it more than once), or press the RETURN button to exit the display.
TIME: Elapsed time of the current track and remaining time of the current track.
connected to a TV or a stereo using the red and white AUDIO OUT jacks on the DVD. 33
EN
1L25
desired item, and then press the ENTER button. If OTHER is selected on the AUDIO, SUBTITLE
or DISC MENU setting screen, the Language Code setting screen will appear. Press the Number buttons to enter the desired language code while referring to the list on page 38.
SET-UP LANGUAGE CONTROLS DISC MENU LANGUAGE CODE
EXIT: SETUP
CANCEL: RETURN
screen is displayed. Notes Language Setting for Audio and Subtitle is not available with some discs, so use the Audio and the Subtitle button. Details are on pages 31 and 32. You can also select an item by entering the number besides it using the Number buttons.
When you change the setup items, press the STOP
34
EN
1L25
DISPLAY SETTINGS
DVD 1 Press the SETUP button in STOP mode.
The setup screen will appear.
SET-UP 1.LANGUAGE 2.DISPLAY 3.AUDIO 4.PARENTAL
ANGLE ICON (Default: ON) Display or not display the Angle icon on the screen.
SET-UP DISPLAY CONTROLS 1.TV ASPECT 2.PANEL DISPLAY 3.ANGLE ICON 4.AUTO POWER OFF 5.BACKGROUND SELECT: / EXIT: SETUP 4:3 LETTER BOX BRIGHT ON ON BLUE SET: ENTER CANCEL: RETURN
AUTO POWER OFF (Default: ON) Set or not set to turn off after the screen saver is started and no keys are pressed for 35 minutes.
SET-UP DISPLAY CONTROLS
1.TV ASPECT 2.PANEL DISPLAY 3.ANGLE ICON 4.AUTO POWER OFF 5.BACKGROUND SELECT: / EXIT: SETUP
SELECT: EXIT:
/ SETUP
SET-UP DISPLAY CONTROLS 1.TV ASPECT 2.PANEL DISPLAY 3.ANGLE ICON 4.AUTO POWER OFF 5.BACKGROUND SELECT: / EXIT: SETUP 4:3 LETTERBOX BRIGHT ON ON BLUE SET: ENTER CANCEL: RETURN
SET-UP DISPLAY CONTROLS TV ASPECT 1.4:3 LETTER BOX 2.4:3 PAN & SCAN 3.16:9 WIDE SELECT: EXIT: / SETUP SET: ENTER CANCEL: RETURN
screen will appear. Notes You can also select an item by entering the number besides it using the Number buttons.
PANEL DISPLAY (Default : BRIGHT) Adjust the brightness of the display of the unit. Auto: Stays dim only during playback.
SET-UP DISPLAY CONTROLS 1.TV ASPECT 2.PANEL DISPLAY 3.ANGLE ICON 4.AUTO POWER OFF 5.BACKGROUND SELECT: EXIT: / SETUP 4:3 LETTER BOX BRIGHT ON ON BLUE SET: ENTER CANCEL: RETURN
SET-UP DISPLAY CONTROLS PANEL DISPLAY 1.BRIGHT 2.DIMMER 3.AUTO SELECT: EXIT: / SETUP SET: ENTER CANCEL: RETURN
35
EN
1L25
AUDIO SETTINGS
DVD 1 Press the SETUP button in STOP mode.
The setup screen will appear.
SET-UP 1.LANGUAGE 2.DISPLAY 3.AUDIO 4.PARENTAL
DTS (Default: OFF) On : Output DTS sound Set to On when the unit is connected to DTS Decoder.
SET-UP AUDIO CONTROLS 1.DRC 2.DOLBY DIGITAL 3.DTS 4.DOWN SAMPLING OFF ON OFF AUTO
SELECT: EXIT:
SELECT: / EXIT: SETUP SET: ENTER CANCEL: RETURN
/ SETUP
Down Sampling (Default: AUTO) Set the output for the DVD recorded in PCM 96 kHz (96 kHz or 48 kHz)
Press the Arrow buttons (K/L) to select an item,
SELECT: EXIT:
/ SETUP
AUDIO OPTIONS 1.DRC 2.DOLBY DIGITAL 3.DTS 4.DOWN SAMPLING OFF ON OFF AUTO
SELECT: EXIT:
/ SETUP
SET-UP AUDIO CONTROLS DOWN SAMPLING 1.AUTO 2.48kHz 3.96kHz SELECT: EXIT: / SETUP SET: ENTER CANCEL: RETURN
DRC (Default: OFF) On: DRC (Dynamic Range Control) This function is for controlling the range of sound volume. By compressing the range of sound volume, it is possible not only to suppress the output of loud sound at night and but also to raise the volume of low sound.
This function is effective only for the sound record-
activated and no sound will come out. If you select AUTO, sound will be down sampled at 48 kHz.
SELECT: EXIT:
/ SETUP
Dolby Digital (default: ON) On : Output by Dolby Digital Set to On when the unit is connected to a Dolby Digital Decoder.
SET-UP AUDIO CONTROLS 1.DRC 2.DOLBY DIGITAL 3.DTS 4.DOWN SAMPLING OFF ON OFF AUTO
SELECT: EXIT:
/ SETUP
36
EN
1L25
PARENTAL LOCK
DVD 1 Press the SETUP button in STOP mode.
The setup screen will appear.
SET-UP 1.LANGUAGE 2.DISPLAY 3.AUDIO 4.PARENTAL
SELECT: EXIT:
/ SETUP
ALL 8 7 [NC-17] 6 [R] 5 SELECT: EXIT: / SETUP SET: ENTER CANCEL: RETURN
CONTROL LEVELS
SELECT: / EXIT: SETUP SET: ENTER CANCEL: RETURN
ALL
Only DVD software intended for general use and children can be played back.
Level 1
CHANGE and enter a new password. Then press the ENTER button.
SET-UP PARENTAL CONTROLS PASSWORD Please enter a 4-digit password. ----
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited. Notes
With some DVDs, it may be difficult to find if they
EXIT: SETUP
CANCEL: RETURN
are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
Record the password in case you forget it.
37
EN
1L25
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on pages 31 and 32. If you choose any other languages, --- will be displayed instead. (3 letter language codes are written in square brackets.) EN 38
1L25
TROUBLESHOOTING GUIDE
If the DVD/VCR COMBINATION UNITS does not perform properly when operated as instructed in this Owner's Manual, check the player consulting the following checklist.
PROBLEM
No power.
D V D V C R
CORRECTIVE ACTION
V C R
D V D
Make sure the power plug is connected to an AC outlet. Make sure the power is turned on. The player does not respond to. Check if the power plug is connected to an AC outlet. the remote control. Check the batteries in the remote control. . Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote. You have to be within 7 m of the player. Check if the correct mode is selected. If not switch the mode by pressing the DVD or the VCR button, whichever you need, on the remote control. Timer recording is impossible. Make sure the timer recording is set correctly. Make sure the power is off. Make sure the VCR clock is set correctly. Cannot go into Record mode. Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape. Put he player in VCR mode. Press the VCR button on the remote control so that the green VCR OUTPUT light is lit. ) button on the Playback picture is partially noisy. Adjust tracking control for a better picture by pressing the CHANNEL ( VCR. Cannot view a tape but the Head cleaning may be necessary. Refer to AUTO HEAD CLEANING . audio is OK. Make sure the VCR is not in the Menu mode. No, or poor, playback picture. Select channel 3 or 4 on your TV, then press the VCR/TV button so that the VCR/TV indicator on the VCR comes on. Fine tune your TV. TV programs cannot be seen Re-check the ANT. IN and ANT. OUT connections. See page 14. normally. Press the VCR/TV button so that the VCR/TV indicator on the VCR disappears. Press the VCR button on the remote control to put it in the VCR mode. Check if the green VCR OUTPUT light is lit. Then, set it to the TV position by pressing the VCR/TV button. The VCR/TV light goes off. Video or color fades in and out You cannot copy a copyrighted video tape. You are experiencing copy guard protection. when making a copy of a video tape. Cannot remove the tape. Check if the player is in the VCR mode. If not, press the VCR button on the remote control to switch the mode. No picture. Connect the video cables firmly. Insert a correct video disc that plays on this player. Press the DVD button on the remote control. Check if the DVD OUTPUT Light is lit. Then try other DVD feature buttons. Insert the disc. Disc cannot be played. Clean the disc. Place the disc correctly, with the label side up. Cancel the parental lock or change the control level. Connect the audio cables firmly. No sound. Turn the power of the audio component on. Correct the audio output settings. Correct the input settings on the audio component. Make sure to use a DIGITAL AUDIO OUT jack when outputting the DTS audio. No DTS sound. Connect the player directly to the TV. Distorted picture. There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction. Although pictures may stop for a moment, this is not a malfunction. Audio or subtitle language The selected language is not available for audio or subtitles on the DVD. does not match the set up This is not a malfunction The camera angle cannot be The DVD does not contain sequences recorded from different camera angles. changed. This is not a malfunction. Audio or subtitle language can The DVD does not contain audio source or subtitles in the selected language. not be changed. This is not a malfunction. Prohibited icon appears on the That operation is prohibited by the player or the disc. screen, prohibiting an operation. This is not a malfunction.
Notes Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owners Manual for details on correct operations. Playback from a desired track and random playback are not available during program playback. 39
EN
1L25
HANDLING PRECAUTIONS
SERVICING
Should your DVD/VCR COMBINATION UNITS become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-968-3429 to locate an Authorized Service Center.
CABINET CLEANING
Wipe the front panel and other exterior surfaces of
the DVD/VCR COMBINATION UNITS with a soft cloth immersed in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray
NOTES:
Remember to read the instructions included with the video head cleaner before use. Clean video heads only when problems occur.
insecticide liquid near the DVD/VCR COMBINATION UNITS. Such chemicals may cause damage and discoloration to the exposed surfaces.
TROUBLESHOOTING GUIDE in this Owners Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
Use discs which have the following logos on them. To clean-off, use a soft cloth. Do not use a hard cloth since this will mar the disc. Wipe the disc in a straight line from center to edge. Never wipe with a circular motion.
not used.
40
EN
1L25
SPECIFICATIONS
Product type: Discs: DVD player with Video Cassette Recorder DVD video Audio CD Video Cassette tape VHF Channel 3 or 4. 120 V AC +/- 10%, 60 Hz +/- 0.5% 25 W (standby: 7.2 W) 5C to 40C W 17-1/8 (435 mm) H 4 (99 mm) D 10-1/2 (266 mm) Weight: 8.8 lbs (4 kg)
Designs and specifications are subject to change without notice. If there is a discrepancy between languages, the default language will be English.
41
EN
1L25
VIDEO DVD OPERATION OUTPUT VCR OPERATION CHANNEL TIMER SET VCR/TV OPEN/CLOSE STOP SKIP/REV PLAY FWD/SKIP STOP/EJECT REW PLAY F.FWD REC/OTR CST.IN L AUDIO R
25
23 24 22
21 20
19 18
17 16
15
PANEL REMOTO
27 28
1 4 7 2 5 8 0
DISPLAY DVD POWER SPEED AUDIO
26
56 55
SKIP/CH. VCR/TV
13 11 14 12 10
3 6 9
+100
SLOW
29
54 53 52 51 50 49 48
+ 10
VCR PAUSE
30 31 32 33
RECORD PLAY STOP
34 35 37 39 41
MENU
36 38 40
47
RETURN
CLEAR/ C.RESET
46 45 43 44 42
MODE
ZOOM
A-B
1. Bandeja de carga del disco 2. Luz DVD OUTPUT (verde) Esta luz aparece cuando el DVD/VCR est en modo DVD. Usted slo puede mirar DVDs cuando la Luz DVD OUTPUT verde est encendida. Para hacer que la Luz DVD OUTPUT verde se encienda, presione el Botn DVD en el control remote o el Botn OUTPUT en el panel delantero. 3. Luz VCR OUTPUT (Verde) Esta luz aparece cuando el DVD/VCR est en el modo VCR. Usted puede slo mirar cintas cuando la Luz VCR OUTPUT verde est encendida. Para hacer que la Luz VCR OUTPUT verde se encienda, presione el Botn VCR en el control remote o el Botn OUTPUT en el panel delantero. 4. CASSETTE COMPARTMENT 5. Luz REC/OTR Se enciende durante la grabacin. 6. Luz TIMER SET La luz de temporizador en la VCR no se enciende durante las grabaciones con temporizador o grabacin con temporizador de un toque (OTR). Destella cuando se presiona el botn TIMER SET para una grabacin con temporizador pero no hay cinta en la VCR. Destella cuando se terminan todas las grabaciones con temporizador o grabaciones de un toque. 7. Botn POWER Presione para conectar y desconectar la alimentacin. 8. Luz POWER Se enciende cuando la alimentacin est conectada.
9. Toma VIDEO IN Conecte aqu un cable de vide procedente de la toma de salida de vide de un camcorder, otro VCR o una fuente de vide (reproductor de discos lser, camcorder, etc.). 10. Tomas AUDIO IN Conecte aqu cables de audio procedentes de las tomas de salida de audio de un camcorder, otro VCR o una fuente de audio. 11. Botn TIMER SET Presione para poner el VCR en modo de espera para una grabacin con temporizador. 12. Luz CASSETTE IN Se enciende cuando un cassette est en el VCR. 13. Luz VCR/TV Se enciende cuando el VCR est en la posicin VCR, y se apaga cuando est en la posicin TV. 14. Botones CHANNEL En el modo VCR, presione para cambiar canales TV en el VCR; presione para ajustar el seguimiento durante reproduccin de movimiento normal o lento; presione para remover fluctuaciones verticales en una imagen fija. 15. Botn REC/OTR (VCR) Presione una vez para empezar una grabacin. Presione 2 veces o ms y la unidad grabar en incrementos de 1/2 hora. 16. Botn F.FWD (VCR) Presione para avanzar rpidamente la cinta o ver la imagen rpidamente en avance durante reproduccin. (Bsqueda en Avance). Cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador), presione para determinar su seleccin y proceder al siguiente paso que usted desea entrar. Presione para determinar los modos de ajuste del men en pantalla. Presione para aadir o cancelar nmeros de canal durante preajuste de canal. 17. Botn PLAY (VCR) Presione para empezar la reproduccin. Presione para entrar cifras cuando se ajusta un programa (Por ejemplo: ajuste del reloj o programa con temporizador). Presione para avanzar los ajustes durante los "men en la pantalla". 18. Botn REW (VCR) Presione para rebobinar la cinta o para ver la imagen rpidamente hacia atrs durante el modo de reproduccin (Bsqueda en rebobinado). Presione para cancelar un ajuste del programa con temporizador cuando est en los "men en la pantalla". Presione para corregir las cifras cuando se ajusta el programa (Por ejemplo: ajuste el reloj o el programa con temporizador). Presione para agregar o borrar nmeros de canal durante el prefijado de canales. 19. Botn STOP/EJECT (VCR) GBotn de expulsin Plselo para sacar el videocasete de la VCR. SP
1L25
42
20.
30.
31. 32.
G Botn Stop Presione detener el movimiento de la cinta. Presione para entrar dgitos cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de ajuste del men en pantalla. Botn OUTPUT Presione para seleccionar el modo DVD o el modo VCR. G Usted puede cambiar el modo de salida ya presionando el Botn OUTPUT en el panel delantero o ya presionando el Botn DVD o VCR en el control remote. Sin embargo, si usted presiona el Botn OUTPUT en el panel delantero primero, usted necesita volver a seleccionar el modo correspondiente presionando el Botn DVD o el Botn VCR en el control remote. Botn FWD/SKIP (DVD) Reproduce desde el inicio del siguiente captulo o pista. Retenga abajo para avanzar rpidamente la reproduccin. Botn PLAY (DVD) Comienza la reproduccin del contenido del disco. Botn SKIP/REV (DVD) Reproduce desde el inicio del captulo o pista actual. Retenga abajo para reproduccin inversa rpida. Botn STOP (DVD) Detiene la operacin del disco. Botn OPEN/CLOSE Presione para insertar discos en o removerlos de la bandeja de disco. Ventanilla de Sensor Remoto, Visualizacin Botn SPEED Presiona para seleccionar la velocidad de grabacin de VCR (SP o SLP) Botn POWER Presione para conectar y desconectar la alimentacin. Botones numricos GModo DVD Presione para seleccionar directamente una Pista (CD de Audio) para reproduccin. Presione para programar Pistas (Dcde Audio) para reproducir. GModo VCR Presione para seleccionar canales de TV en el VCR. Para seleccionar canales, entre nmeros de canal como un nmero de dos dgitos para los resultados ms rpidos. Por ejemplo, para seleccionar canal 6, presione 0.6. Botn +100: Si usted desea seleccionar canales 100 y arriba, presione este Botn primero, luego presione los dos dgitos ltimos. Por ejemplo, para seleccionar canal 125, presione Botn +100 primero, luego presione 2 y 5. Botn DISPLAY GModo DVD Presione para tener acceso o remover la pantalla de visualizacin durante reproduccin DVD o CD de audio. GModo VCR Presione para tener acceso o remover visualizacin de estado en pantalla de VCR. Botn DVD Presione antes de utilizar el control remote para funciones DVD. Botn h GModo DVD Presione para ver la imagen DVD en movimiento de inversin rpida o para invertir la reproduccin de un DC de Audio. GModo VCR Presione para rebobinar la cinta o para ver la imagen rpidamente en inversin durante el modo de reproduccin.(Bsqueda en Rebobinado). Presione para cancelar un ajuste de programa con temporizador.
33.
34. 35.
40. 41.
45.
Presione para corregir dgitos cuando ajuste programa. (Por ejemplo: ajuste de reloj o programa con temporizador). Presione para aadir o cancelar nmeros de canal durante preajuste de canal. Botn Stop Presione detener el movimiento de la cinta. Presione para entrar dgitos cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de ajuste del men en pantalla. Botn RECORD Presione para iniciar una grabacin. O, presione repetidamente para iniciar una grabacin de Un-Toque. Botn MENU GModo DVD Presione para visualizar el men del Disco. GModo VCR Presione para tener acceso al men VCR. Botn TITLE Botn SETUP Presione para entrar el modo de preparacin. Botn ZOOM Ampla parte de una imagen reproducida-DVD. Botn MODE Activa modo de reproduccin de programa o reproduccin aleatoria cuando se reproducen CDs o MP3. Ajusta Nivel de negro o TruSurround SRS. Botn SUBTITLE Presione para seleccionar un idioma de subttulo deseado. Botn ANGLE Presione para cambiar el ngulo de cmara para ver la secuencia que se est reproduciendo desde un ngulo diferente. Botn REPEAT Repite la reproduccin del disco, ttulo, captulo o pista actual. Botn A-B REPEAT Repite la reproduccin de una seccin seleccionada. Botn SEARCH MODE GModo DVD Presione para tener acceso o remover la indicacin de bsqueda, que le permite ir directamente a un Ttulo/Captulo/Pista/Tiempo especificado. GModo VCR Presione para avanzar o rebobinar rpidamente la cinta a una longitud especfica de tiempo. Botn CLEAR/C.RESET GModo DVD Presione para reponen el ajuste. GModo VCR Presione para reponer el contador. Presione para salir de la pantalla MEMU. Botn RETURN Vuelve a la operacin previa. Botones de flecha Utilice cuando haga ajustes mientras mira la indicacin en una pantalla de TV. Botn ENTER Presione para aceptar un ajuste. Botn g GModo DVD Presione para avanzar rpidamente el Disco. Presione el Botn PAUSE, luego presione el Botn FWD iniciar a reproduccin en movimiento lento. Presione el Botn FWD repetidamente para cambiar la velocidad de avance del movimiento lento. GModo VCR Presione para avanzar rpidamente la cinta o ver la imagen rpidamente en avance durante reproduccin. (Bsqueda en Avance). Cuando ajuste prograSP
1L25
43
50.
51. 52.
53.
ma. (Por ejemplo: ajuste reloj o programa con temporizador), presione para determinar su seleccin y proceder al siguiente paso que usted desea entrar. Presione para determinar los modos de ajuste del men en pantalla. Presione para aadir o cancelar nmeros de canal durante preajuste de canal. Botn PLAY Presione para comenzar reproduccin. Presione para entrar dgitos cuando ajuste programa. (Por ejemplo: ajuste reloj o programa con temporizador). Presione para seleccionar los modos de ajuste del men en pantalla. Botn VCR Presione antes de utilizar el control remote para funciones de VCR. Botn PAUSE GModo DVD Presione para pausar la reproduccin de Disco. Presione repetidamente para avanzar la imagen DVD paso a paso (o un fotograma cada vez). GModo VCR Mientras graba, presione para detener provisionalmente la grabacin (pausa). Presione por segunda vez para reanudar la grabacin normal. Usted no puede pausar Grabacin de Un-Toque. O, presione durante la reproduccin de cinta para congelar la imagen. Botn SLOW Durante la reproduccin de cinta, presione mirar la cinta de vide a movimiento lento. Presione de nuevo para reanudar la reproduccin normal. Este Botn no afecta la reproduccin DVD.
54. Botn VCR/TV Utilice para seleccionar la posicin VCR o TV. Si la Luz VCR/TV aparece en la parte delantera del VCR, est en la posicin VCR (en cualquier modo VCR o DVD). Si la Luz VCR/TV no aparece en la parte delantera del VCR, est en la posicin TV. GPosicin VCR Cuando la Luz VCR OUTPUT verde aparece en la parte delantera del VCR, utilice la VCR para mirar una cinta, para mirar un programa de TV mientras lo graba o para mirar una radiodifusin de TV utilizando los botones CHANNEL o Numricos para cambiar canales en la VCR. Cuando la Luz DVD aparece en la parte delantera de la DVD, utilice el DVD para mirar la reproduccin de Disco o mens. GPosicin de TV Utilice para mirar TV (cambiando canales en el TV) o para mirar un programa mientras graba otro. 55. Botones SKIP/CH GModo DVD Presione para saltar Captulos o Pistas. GModo VCR Presione para cambiar canales de TV en la VCR.
Notas Para utilizar el control remote para operar el UNIDADES COMBINADAS DE DVD/VCR y sus funciones, presione el Botn DVD en el control remote antes de presionar otros botones DVD. Verifique que la Luz DVD OUTPUT verde est encendida. Para utilizar el control remote para operar la VCR y sus funciones, presione el Botn VCR en el control remote antes de presionar otros botones VCR. Verifique que la Luz VCR OUTPUT verde est encendida.
58
DVD/VCR OUT
VISIN TRASERA
57
59
60
COMPONENT VIDEO OUT DVD/VCR AUDIO OUT L Y S-VIDEO DIGITAL AUDIO OUT Cb OUT PCM / BITSTREAM COAXIAL Cr
67 66 65
64 63
62 61
56. Botn AUDIO Presione para seleccionar un idioma de audio deseado o modo de sonido. 57. Cordn de Alimentacin AC
58.
59.
60.
61.
Conecte a una toma de corriente AC estndar para suministrar corriente al UNIDADES COMBINADAS DE DVD/VCR. Tomas AUDIO IN Conecte aqu los cables de audio procedentes de las tomas de salida de audio de un camcorder, otra VCR o una fuente de audio. Tomas DVD/VCR AUDIO OUT Conecte aqu los cables de audio provistos y a las tomas de entrada de audio de un televisor u otro equipo de audio. Tomas COMPONENT VIDEO OUT Conecte aqu los cables de vide componente opcionales y a las tomas de entrada de Vide componente de un televisor. Toma COAXIAL Conecte aqu un cable de audio digital coaxial opcional y a la toma de entrada Audio Digital Coaxial de un descodificador o receptor de audio.
Conecte aqu un cable de S-Vide opcional y a la toma de entrada de S-Vide de un televisor. Toma DVD/VCR VIDEO OUT Conecte aqu el cable de vide amarillo (provisto) y a la toma de entrada de Vide de TV. Toma VIDEO IN Conecte un cable procedente de la toma de salida de vide de un camcorder, otra VCR o una fuente de audiovisual (reproductor de disco lser, reproductor de disco de vide, etc.) aqu. Cambio CH3/CH4 Ajuste a canal 3 4 para utilizar su TV con su VCR. Toma ANT-IN (Entrada de Antena) Conecte su antena o cable aqu. Toma ANT-OUT (Salida de Antena) Utilice el cable coaxial RF provisto para conectar esta toma a la Toma ANTENNA IN en su TV. Caja de cables o Sistema de Radiodifusin Directa.
Notas La toma S-VIDEO OUT, toma COAXIAL, toma OPTICAL y tomas COMPONENT VIDEO OUT son slo tiles en el modo DVD.
SP
1L25
44
CAMBIO DE VCR/DVD
Como este producto se utiliza del reproductor VCR y DVD, es necesario cambiar uno del otro.
CAMBIO AL MODO VCR
Presione el Botn VCR en el control remote. (Verifique que la Luz VCR OUTPUT est enendida.)
Notas Presionando slo el Botn OUTPUT en el panel delantero no cambia el modo del control remote. Usted siempre necesita seleccionar el modo correcto en el control remote, tambin.
POWER
VIDEO DVD OPERATION OUTPUT VCR OPERATION CHANNEL TIMER SET VCR/TV OPEN/CLOSE STOP SKIP/REV PLAY FWD/SKIP STOP/EJECT REW PLAY F.FWD REC/OTR CST.IN L AUDIO R
POWER SPEED
AUDIO
1 4 7
2 5 8 0
3
SKIP/CH.
6
VCR/TV
9
+100
SLOW
VD OPERATION
OUTPUT
DVD OUTPUT Light DVD button VCR OUTPUT Light VCR button VCR OPERATIO
+ 10
VCR PAUSE
DISPLAY
DVD
PLAY
STOP RECORD
MENU
LAY
FWD/SKIP
STOP/EJECT REW
SETUP TITLE MODE ZOOM
ENTER RETURN
SEARCH MODE CLEAR/ C.RESET
OUTPUT button
A-B
45
SP
1L25
CONEXIONES
DVD/VCR A CONEXIN DE TV
1. Desconecte el cordn de alimentacin AC del toma de corriente AC. 2. Desconecte la antena o cable del TV. 3. Conecte la antena o cable a la toma ANT.IN del UNIDADES COMBINADAS DE DVD/VCR. 4. Conecte el UNIDADES COMBINADAS DE DVD/VCR al TV utilizando el cable RF. 5. Enchufe los cordones de alimentacin CA del UNIDADES COMBINADAS DE DVD/VCR y TV dentro de las tomas de corriente AC.
CONECTANDO A UN TV
Por favor, vea la [Fig.1] en la pgina 14 para detalles.
CONECTADO A UN TV QUE TIENE TOMA DE ENTRADA DE SVDEO o TOMAS DE ENTRADA DE VDEO COMPONENTE
Por favor, vea la [Fig. 2] en la pgina 14 para detalles.
CONECTANDO A UN AMPLIFICADOR EQUIPADO CON TOMAS DE ENTRADA DIGITAL, TALES COMO PLATINA MD O PLATINA DAT
Por favor, vea la [Fig. 4] en la pgina 15 para detalles.
PREPARACIN
PREPARACIN DE CANAL AUTOMTICA
VCR 1 Conecte el TV y ponga el TV en el canal 3 4. 2 Conecte el VCR presionando [POWER].
Ambas Luces POWER y VCR/TV se encendern.
46
SP
1L25
PREPARACIN DE RELOJ
VCR
Ajuste el reloj con precisin para grabacin con temporizador automtica adecuada. Le sugerimos que usted utilice un TV o estacin de radio como su fuente de tiempos.
REPRODUCCIN DE UN DISCO
REPRODUCIENDO UN DVD, VIDEO O UN CD AUDIO
DVD Para empezar
Conecte la alimentacin del TV, amplificador y cualquier otro componente que se encuentre conectado al DVD. (Cambie el sistema de entrada para que se adapte DVD y compruebe que el volumen de sonido sea correcto).
CD
3 Ajuste el reloj.
1) Ajuste el mes
duccin empezar luego desde el primer captulo o pista del disco. Usted necesita presionar el Botn PLAY slo cuando la bandeja se ha cerrado presionando el Botn OPEN/CLOSE.
47
SP
1L25
1-800-4-MY-HOME R
www.sears.com
Our Home
For repair of carry-in items like vacuums, lawn equipment, and electronics, call or go on-line for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparacin a domicilio, y para ordenar piezas:
1-800-361-6665 (Canada)
Au Canada pour service en franais:
1-800-LE-FOYERMC
(1-800-533-6937) www.sears.ca
1-888-SU-HOGARSM
(1-888-784-6427)
R R
MC
Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co. Marca Registrada / TM Marca de Fbrica / SM Marca de Servicio de Sears, Roebuck and Co. Marque de commerce / MD Marque dpose de Sears, Roebuck and Co.
LIMITED 90 DAY WARRANTY If this (product) experiences any failure due to a defect in material or workmanship within 90 days from the date of purchase, return it to your nearest Sears Service Center, and Sears will repair it free of charge. After 90 days and until one (1) year from the date of purchase, Sears will replace defective parts free of charge. You pay for labor. This warranty applies only if this (product) is used for private household purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D/817WA, Hoffman Estates, IL 60179 Sears Roebuck and Co., Dept. 817WA Hoffman Estates, IL 60179 For the location of a Sears Service Center in your area : 1-800-488-1222
Printed in China 0VMN03219 H9228UD #####