You are on page 1of 14

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

2.18.5

M:DCBCTRLV3
Types of DCBCTRL M:DCBCTRLV3 S30861-Q2128-X-*

Test Connector

LED green LED red LED red

AC BAT 0 RESET

DC BAT 1 TEMP

LED green LED red LED red

Selectable Battery Manufacturer

Selectable Battery Capacities

Selectable Slot-ID

Fig. 2.65

M:DCBCTRL V3

96

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

LEDs AC Presence of the primary power source This LED is on if no mains breakdown alarm is activated DC output voltage within specified tolerance This LED is on if the alarm 48OTB is not activated; the LED must be off in case the internal supply voltage of the controller board is down. Battery system 0 or temperature sensor on battery system 0 is faulty. This LED is on if the alarms BAT_0_FAIL and/or TEMP_SENSE_FAIL0 are activated. Battery system 1 or temperature sensor on battery system 1 is faulty. This LED is on if the alarms BAT_1_FAIL and/or TEMP_SENSE_FAIL1 are activated. Over- / Undertemperature protection This LED is on if the over- or undertemperature protection is triggered. This LED is active during RESET. After Power On of the AC/DC controller this LED goes on. As soon as the microcontroller enters the state of normal operation (is able to retrigger the watchdog and activate the CAN Bus interface), the LED goes off.

DC

BAT 0

BAT 1

TEMP

RESET

Switches Selectable Battery Manufacturer: For selecting a proper characteristic curve for battery charging. Manufacturer Oerlikon Sonnenschein / Exite / Hawker Tab. 2.13 on off Bit 0 Bit 1 not used not used

Battery Manufacturer

Batt Type

Bit 1 Bit 0

ON

Fig. 2.66

Battery Manufacturer DIP Switch

A30808-X3247-K83-7-7620

97

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

Selectable Battery Capacities: 0Ah (no battery), 5Ah, 10Ah,...1275Ah. The battery capacities can be set with two 8 bit DIP switches, one for each battery block; 1 LSB = 5Ah. The setting is calculated by adding all values where the contacts of the DIP switch are set to ON. 640 Ah 320 Ah 160 Ah 80 Ah 40 Ah 20 Ah 10 Ah 5 Ah

ON

Fig. 2.67

Battery Capacity DIP Switch

The state of the object BATTERY does not depend on the existence of a real battery. It depends on the Battery Capacity DIP switch settings on the DCBCTRL module. If one of these two DIP switches is set to a value different from 0 Ah, the respective HMO BATTERY goes to enabled. Selectable Slot-ID: The CAN-Bus address can be set with a 2 bit DIP switch in order to distinguish between two different AC/DC frames mounted to one rack.

Both switches must be in different positions.

Address ACDCP0 ACDCP1 Tab. 2.14 Slot-ID on off

Bit 0 off on

Bit 1

Slot-ID

Bit 1 Bit 0

ON

Fig. 2.68

DCBCTRL Slot-ID DIP Switch

98

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

TEMP RESET

Over / Under Temperature protection has been activated. Active during reset operation of microcontroller.

Connectors VDC + / Terminals for system voltage measurement

COMM Port Serial interface connector

2.18.2

M:DCBCTRLDV1
Types of DCBCTRL M:DCBCTRLDV1 S30861-U4103-X-* Intended for Ethernet Test Connector

Cap Test

Rough Test

FL/EQU

Serial Interface

AC LED green

DC green

BAT_F red

Temp red

Reset red

EQU yellow

MIN yellow

MAJ red

LVDS red

Breaker red

Fig. 2.60

DCBCTRLDV1

A30808-X3247-K83-7-7620

89

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

LEDs AC Presence of the primary power source The LED is on if no mains breakdown alarm is activated DC output voltage within specified tolerance The LED is on if the alarm 48OTB is not activated; the LED must be off in case the internal supply voltage of the controller board is down. The Bat-Fail alarm is activated if one of these conditions has occurred: 1. Temperature sensor on battery is off or failed. 2. Battery Rough Test failed. 3. Battery Capacity Test failed. 4. Battery connected with wrong (inverted) polarity. 5. Signal TEMP_SENSE_FAIL0 is activated (temperature is above 81C (178F), or below -49C (-56F)) This LED is on if the over-/undertemperature protection is activated (temperature is above 67C (153F), or below -1C (30F)) This LED is active during RESET. After Power On of the AC/DC controller this LED goes on. As soon as the microcontroller enters the state of normal operation, the LED goes off. This LED goes on if the charging voltage is switched from float charging (depending on battery type and battery temperature) to equalize charging (setting range: -55.4V ... -57.4V, factory setting: -56.4V). The equalize mode is switched on via push button Fl/EQU on the DCBCTRL front panel, or by software. The equalize mode is switched off after 30 minutes (factory setting), or if one of the following alarms / conditions occurs: 1. AC out of specified range. 2. DC out of specified range. 3. Temp protection. 4: Temp sensor fail. 5: LVD disconnect alarm. 6: Breaker disconnect. 7. Temp alarm. 8. Battery capacity equals to zero. 9. Battery fail alarm 10. Battery capacity test 11. Battery rough test This LED is on if only one rectifier is faulty. This LED is on if two or more rectifiers are faulty.

DC

BAT_F

Temp

Reset

EQU

MIN MAJ

90

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

LVDS

This LED is on if the Low Voltage relay has disconnected (i.e. the magnitude of the DC battery voltage is below -40V 0.5V). The relay is switched on again if the magnitude of the DC battery voltage is above -45V. This LED is on if the battery breaker has disconnected. (currently not used)

Breaker

Switches Cap test Rough test FL \ EQU Pushbutton for starting battery capacity test Pushbutton for starting battery rough test Pushbutton for switchover from float charging to equalize charging

Connectors V+ / VRS 232 ETH Terminals for system voltage measurement Serial interface connector Ethernet connector (optional)

2.18.3

M:DCBCTRLM-2
Types of DCBCTRL M:DCBCTRLM-2 S30861-S2331-X-*

A30808-X3247-K83-7-7620

91

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

2.9

ACT
Types of ACT 2.9.1 ACTAV2 2.9.2 ACTC12V1 2.9.3 ACTCV1 2.9.4 ACTC-3V1 2.9.5 ACTMV2 2.9.6 ACTP S30861-Q2053-X-* S30861-Q2138-X-* S30861-Q2029-X-* S30861-Q2194-X-* S30861-U2079-X-*

2.9.1

ACTAV2
Types of ACTAV2 ACTAV2 S30861-Q2053-X-*

For Base Rack/Shelter/Server: part of ACTMV2

Fig. 2.18

ACTAV2

42

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

X8

X7

X6

X5

X10

X9

X4

X3

X2

X1

Fig. 2.19

Connector Locations of ACTA In case of alarm signal modifications, please refer to the respective base station installation manual (IMN) for more information on the alarm signal assignment.

A30808-X3247-K83-7-7620

43

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

2.9.2

ACTC12V1
Types of ACTC12V1 ACTC12V1 S30861-Q2138-X-*

Fig. 2.20

ACTC12V1

H X 0

H X 1

H X 2

Temperature Sensors

W 1 W 4 W 7

W 2 W 5 W 8

W 3 W 6 W 9
SMOKE RDO SIS BB0 BB1 BB2 BB3

Alarm_IN 16 1

Fig. 2.21

Connector Locations of ACTC12V1 In case of alarm signal modifications, please refer to the respective base station installation manual (IMN) for more information on the alarm signal assignment.

44

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

2.9.3

ACTCV1
Types of ACTCV1 ACTCV1 S30861-Q2029-X-*

Fig. 2.22

ACTCV1

H X 0

H X 1

H X 2

Temperature Sensor

W 1 W 4 W 7

W 2 W 5 W 8

W 3 W 6 W 9 24
SMOKE RDO SIS BB0 BB1 BB2

1 Alarm_IN

Fig. 2.23

Connector Locations of ACTCV1 In case of alarm signal modifications, please refer to the respective base station installation manual (IMN) for more information on the alarm signal assignment.

A30808-X3247-K83-7-7620

45

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

2.9.4

ACTC-3V1
Types of ACTC-3V1 ACTC-3V1 S30861-Q2194-X-*

SMOKE smoke sensor

RDO rack door open 24

Environmental Alarms 1

Temperature Sensors

Fig. 2.24

ACTC-3V1

In case of alarm signal modifications, please refer to the respective base station installation manual (IMN) for more information on the alarm signal assignment.

46

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

2.9.5

ACTMV2
Types of ACTMV2 ACTMV2 S30861-U2079-X-*

For Base Rack/Shelter: consists of ACTA and ACTP

ACTA

ACTP

Fig. 2.25

ACTMV2

A30808-X3247-K83-7-7620

47

HW:BTSE Modules

HW-Manual Base Transceiver Station Equipment

2.9.6

ACTP
Types of ACTP ACTPV2 ACTPV3 S30861-Q2052-X-* S30861-Q4088-X-*

For Extension and Service Rack/Shelter

Fig. 2.26

ACTP

DIPSwitch

Reset LEDs X5 X4

X2

X6

Mounted on soldering side

Fig. 2.27

Connector Locations of ACTP

48

A30808-X3247-K83-7-7620

HW-Manual Base Transceiver Station Equipment

HW:BTSE Modules

LEDs green red

Active if HW and SW are O.K. (tests successfully passed) Active if C is in reset

Switches

ON

1 Fig. 2.28

Rack/Shelter Address DIP Switch (Factory Setting)

Rack/Schelter Type

Rack/ Schelter No. 0

Switch 1

Switch 2

Switch 3

Switch 4

Base Rack/Schelter

off (open) off (open) off (open) on on off (open) off (open) on off (open) on off (open) on on on on on

Extension Rack/Schelter 0 1 Extension Rack/Schelter 1 2 Service Rack/Schelter 0 Service Rack/Schelter 1 Service Rack/Schelter 2 Service Rack/Schelter 3 Service Rack/Schelter 4 Tab. 2.8 3 4 5 6 7

off (open) on on on

off (open) off (open) on on off (open) on on on

off (open) on on on

ACTP Switch Settings

A30808-X3247-K83-7-7620

49

You might also like