Professional Documents
Culture Documents
calcium chloride CaCl
2
> Ca
2+
+ Cl
+ Cl
sodium phosphate Na
3
PO
4
> Na
+
+ Na
+
+ Na
+
+ PO
4
3
Each equation shows how many ions are produced from each formula when they dissolve in
water. Sodium chloride produces two ions, calcium chloride produces three ions, and sodium
phosphate produces four ions. Even when these salts are made into solutions with the same
concentration, measured as whole formula units per liter, they produce different levels of
conductivity. For example, a solution of sodium phosphate will be twice as conductive as a
solution of sodium chloride with the same concentration.
Pre-Lab Questions
Before handing this lab in, write your answers to these questions.
1. What is an electrolyte and how is it different from a non-electrolyte?
2. Define the terms solute, solvent, and solution in your own words.
3. In your own words, describe the process by which an ionic solute dissolves in water to
make an electrolyte solution.
4. In your own words, describe how electrical current is moved through an electrolyte
solution and how this is different from how electrical current moves through a metal
wire.
5. Do electrolytes carry electricity or produce it? Justify your answer by thinking about
the example of the light bulb and the battery from the introduction.
6. How many ions does one formula unit of MgBr
2
break up into when it dissolves?
How many ions per formula unit does AlCl
3
make?
7. How does the number of ions per formula unit affect the conductivity of a solution?
8. How does changing the concentration of a solution of the same electrolyte change the
conductivity? In other words, what is more conductive, a solution with a high or a low
concentration?
9. Based on your knowledge of ionic compounds, which of the following two
compounds will produce a solution with higher conductivity if the same number of
formula units are dissolved? AlCl
3
or MgBr
2
? Justify your answer.
Materials
Labquest software on a computer
Vernier Conductivity Probe
ring stand
clamp
stirring rod
several 100-mL beakers
distilled water
wash bottle with distilled water
100-ml graduated cylinder
dropper bottle of 0.1 M NaCl
dropper bottle of 0.1 M CaCl
2
dropper bottle of 0.1 M Na
3
PO
4
dropper bottle of 0.1 M C
12
H
22
O
11
(sugar)
dropper bottle of 3% H
2
O
2
(hydrogen peroxide)
Sharpie marker for labelling
Safety
The chemicals used in this activity are all of low toxicity and are used in dilute solutions.
Even so, it is best to wear standard laboratory safety equipment such as splash goggles, long
pants, and nitrile gloves, if desired. Tie back long hair and do not wear dangling jewelry in
the lab.
Part I: Electrolytes vs. Non-electrolytes
Procedure
In this part of the lab you will measure the conductivity of six different substances: distilled
water, hydrogen peroxide (H
2
O
2
) solution, sucrose (C
12
H
22
O
11
) solution, sodium chloride
(NaCl) solution, calcium chloride (CaCl
2
) solution, and sodium phosphate (Na
3
PO
4
) solution.
1. Wear your safety goggles while working in the lab.
2. Set up the Conductivity Probe using the ring stand and clamp. Do not clamp the probe
too tightly and do not submerge the probe completely into water at any time.
3. Set the range selector on the Conductivity Probe to 0 - 200 S/cm.
4. Connect the probe to the computer and start the Logger Lite or Logger Pro software.
5. The software will immediately recognize the probe and produce a data collection
screen.
6. Obtain and label five 100-mL beakers with the formulas of the substances you will be
testing: NaCl, CaCl
2
, Na
3
PO
4
, C
12
H
22
O
11
, and H
2
O
2
. You will use these beakers
throughout this lab without emptying them until it is time to clean up.
7. Fill each beaker with 50 mL of distilled water by measuring with a graduated
cylinder.
8. Test the conductivity of one of the beakers containing distilled water by submerging
the electrode at the bottom completely. Water alone will be the first material you test.
Hold the beaker up to the probe and submerge the end of the probe in the water.
Record the conductivity value on your screen.
9. Now add just one drop of each solution your teacher has provided for you to each
labeled beaker.
10. Stir the NaCl solution with the glass rod. Rinse the rod and dry it before stirring the
next solution. Stir each one with the stirring rod, rinsing and drying in between each
one.
11. Use the Conductivity Probe to measure the conductivity of the NaCl solution. Record
the value in a data table you write down. Dont forget to include distilled water as one
of the substances you tested.
12. Rinse the end of the probe carefully using the wash bottle full of distilled water. This
prevents the probe from giving inaccurate readings when you test the next solution.
13. Now use the probe to measure the conductivity of each of the other solutions. Always
be sure to rinse the probe between tests!
Part II: Electrolyte Conductivity vs. Concentration
Procedure
In this part of the lab you will collect data to show the proportion between concentration and
conductivity for three strong electrolytes.
1. On the Experiment menu, click Data Collection. Choose Events with Entry.
2. For Name enter Number of Drops and for Units enter Drops. Click OK
3. Click the Collect button to start data collection.
4. Raise the beaker containing 50 mL distilled water and one drop of NaCl solution up
over the end of the probe. Click the Keep button and enter 1 for the volume in drops.
5. Add one drop of NaCl solution and stir it using your clean stirring rod.
6. Test the conductivity of the solution by holding it so the end of the probe is
submerged. Swirl it gently, without spilling and watch the conductivity value for
about 5 seconds. Once the reading reaches a steady value, click Keep and enter 2.
7. Repeat this process until you have reached a total of 8 drops.
8. Stop data collection by clicking the Stop button.
9. Next you will use the software to analyze your result by producing a linear regression.
This will calculate the equation of the line and plot a best-fit line for your data.
1. On the Analyze menu choose Linear Fit.
2. When it plots the line and gives you the equation it will be in the form y = mx
+ b. The y variable stands for conductivity, the x value stands for volume in
drops.
3. Record the value of the slope in a data table.
4. Click the File Cabinet icon to Store the data from the first run.
10. Rinse the electrode with the wash bottle.
11. Repeat the data collection procedure with the CaCl
2
solution.
12. Remember to store the data from Run 2 using the File Cabinet icon.
13. Repeat the data collection process with the Na
3
PO
4
solution.
14. As instructed by your teacher, print this graph and/or export the data for further
analysis and formatting in a spreadsheet program. In your report you must include a
well-formatted graph with all three runs properly labeled and showing the slope of
each line.
page break
Post-lab Questions
Answer the following questions in a typed document on a separate paper. As part of your
report you must include the answers to the Pre-lab questions, your formatted and labeled
graph, and the answers to the questions below. This lab does not require a formal lab report.
1. Which of the substances you tested in part one were electrolytes? Which of them were
non-electrolytes? Use your data to justify your answers and recall that distilled water
should have essentially zero conductivity. If your distilled water had a reading slightly
above zero then take this value as equivalent to zero conductivity.
2. Create a data table to compare the conductivity of each different solution with only
one drop of the stock solution.
3. Using the chemical formulas of each compound explain why the conductivity values
follow the pattern that you see.
4. Why do some compounds show essentially zero conductivity?
5. Why are some more conductive than others despite the fact that you added the same
amount of each one?
6. What kind of proportion exists between the conductivity of a solution and the
concentration of ions in the solution? Describe what happens to conductivity as
concentration increases.
7. Compare the slopes of the three lines and put them in order from smallest to largest.
What explains the difference in the slopes since all three were generated starting with
solutions with the same starting concentration?
8. Write equations for when the following salts dissolve in water: Na
2
SO
4
, Mg
3
(PO
4
)
2
,
and Al(OH)
3
.
9. Which of the salts in the previous problem would have the steepest slope if it were
used in Part II of this lab? Which would have the smallest slope? Justify your
answers.
Last updated: Mar 10, 2014