Professional Documents
Culture Documents
I!~, '"
REV 2
SAFETY SUMMARY
This manual applies to the ATRT-03 52, ATRT-03A 52, and ATRT-3B 52 current transformer turns-ratio meters. The operating procedures are virtually the same for all three models, and any differences are clearly described where applicable.
WARNING
Do not remove test leads during a test. Failure to heed this warning can result in electrical shock to personnel and damage to the equipment.
REV 2
TABLE OF CONTENTS
CONVENTIONS USED IN THIS DOCUMENT 1.0 INTRODUCTION 1.1 General Description and Features 1.2 Technical Specifications 1.2.1. ATRT-03 52 Technical Specifications 1.2.2. ATRT-03A 52 Technical Specifications 1.2.3. ATRT-03B 52 Technical Specifications 1.3 Controls and Indicators 2.0 PRE-TESTSETUP 2.1 Operating Voltages 2.2 LCD Screen Contrast Control. 2.3 Printer Paper Control 2.4 Printer Paper 2.5 Replacing the load Tap Changer Controller Fuses 3.0 OPERATING PROCEDURES 3.1 Connection Diagrams 3.1.1. Typical Front Panel Connections 3 .. .2. Typical Connections to a Load Tap Changer (LTC) 1 3.1.3. Typical Connections to a Delta-Wye Transformer 3.2 Setting the Test Voltage 3.3 Setting the Date and Time 3.4 Performing Tests 3.4.1. Entering Test Record Header Information 3.4.2. Testing a Single Phase Transformer 3.4.3. Testing a Dynl (12,000 V/208 V) Transformer 3.4.4. Testing a Three Phase Transformer Using Auto Detect Mode 3.5 Working With Test Records 3.5.1. Saving Test Results to a Test Record 3.5.2. Restoring a Test Record From Flash EEPROM 3.5.3. Restoring a Test Record From a USB Flash Drive 3.5.4. Copying Test Records to a USB Flash Drive 3.5.5. Printing or Displaying a Test Record 3.5.6. Printing a Test Record Directory (ATRT-03 S2 and ATRT-03A S2 Only) 3.5.7. Viewing a Test Record Directory on the LCD Screen (ATRT-03B 52 Only) 3.5.8. Erasing Test Records from the Flash EEPROM 3.5.9. Erasing Test Records from a USB Flash Drive 3.6 Working With Test Plans 3.6.1. Performing a Test Using a Transformer Test Plan 3.6.2. Unloading a Test Plan From the Working Memory 3.6.3. Printing a Test Plan Directory (ATRT-03 52 and ATRT-03A 52 Only) 3.6.4. Viewing a Test Plan Directory on the LCDScreen (ATRT-03B 52 Only) 3.6.5. Printing a Test Plan (ATRT-03 S2 and ATRT-03A S2 Only) 1 2 2 4 4 5 6 7 13 13 13 13 13 14 16 16 16 17 18 26 28 29 29 33 42 52 59 59 62 67 71 74 77 80 82 86 89 89 96 97 99 101
~:'::~~'
3.6.6. 3.6.7. 3.6.8. 4.0 4.1 4.2 5.0
REV 2
104 106 108 112 112 114 116 119 120 128 135
APPENDIX A - TRANSFORMER VECTOR GROUP CODES APPENDIX B - Common APPENDIX D - Australian APPENDIX C - CEI/IEC 60076-1
Transformer
REV 2
ATRT-03 52,
LIST OF TABLES
Table Table Table Table Table Table Table Table Table Table 1. ATRT-03 S2 Technical Specifications 2. ATRT-03A 52 Technical Specifications 3. ATRT-03B 52 Technical Specifications 4. Functional Descriptions of ATRT-03 52 Controls and Indicators 5. Functional Descriptions of ATRT-03A S2 Controls and Indicators 6. Functional Descriptions of ATRT-03B S2 Controls and Indicators 7. Descriptions of Single Phase Test Results Elements (Column Format) 8. Descriptions of Single Phase Test Results Elements (Detailed Format) 9. Descriptions of Dynl Test Results Elements (Column Format) 10. Descriptions of Dyn 1 Test Results Elements (Detailed Format) 4 5 6 8 10 12 39 41 49 51
LIST OF FIGURES
Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure Figure 1. ATRT-03 52 Controls and Indicators 2. ATRT-03A S2 Controls and Indicators 3. ATRT-03B 52 Controls and Indicators 4. Typical Front Panel Cable Connections 5. Typical Connections to a Load Tap Changer (LTC) 6. Typical H & X Cable Connections to a Delta-Wye Transformer 7. Typical Connections to a Single Phase Transformer 8. Typical Connections to a Single Phase Auto Transformer 9. Typical Connections to a Type A Voltage Regulator 10. Typical Connections to a Type B Voltage Regulator 11. Typical Connections to a Donut Type (un-mounted) Current Transformer (CT) 12. Typical Connections to a Multi-Tap Current Transformer 13. Typical Connections to a Bushing Mount CT on a Single Phase Transformer 14. Typical Connections to Bushing Mount Cf''s on Delta Transformer 15. Typical Connections to Bushing Mount Cf''s on Wye Transformer 17. Single Phase Test Results Printout - Column Format 18. Single Phase Test Results Printout - Detailed Format 19. Dyn1 Test Results Printout - Column Format 20. Dynl Test Results Printout - Detailed Format 21. Typical USB Flash Drive (Thumb Drive) Test Record Directory Printout 22. Typical Internal Flash EEPROM Test Record Directory Printout.. 23. Test Plan Test Results Printout 24. Sample Printout of a Test Plan from a USB Flash Drive 25. Sample Printout of a Test Plan from Internal Memory 7 9 11 16 17 18 19 19 20 20 21 22 23 24 25 39 40 48 50 79 79 95 102 103
~\I .
Liv
[:
REV 2
When instructions are provided, the menu item that should be selected is outlined with a rectangle as shown below (option 3 should be selected):
I 3. OPTIOH 4. dPTION
2.
1. OPTION
or-r rou
"2"
_.
2 4
5. OPTIot..j
Warning message
WARNING
Important
NOTE
REV 2
,l
1.0
1.1
INTRODUCTION
General Description and Features
The ATRT-03 52 line is Vanguard's third generation family of microprocessor-based, automatic, three phase, transformer turns-ratio testers. The ATRT-03 52 line consists of the following three models: • • The ATRT-03 52 is a line-powered, built-in thermal printer. 100-240 Vac, 50/60 Hz turns-ratio tester featuring a
The ATRT-03A 52 can be powered either by an internal rechargeable lead acid battery, by 100-240 Vac, or by a 12 Vdc external source. The internal battery provides 3 hours of operational time. The ATRT-03A 52 also features a built-in thermal printer. The ATRT-038 52 is a line-powered, built-in thermal printer. 100-240 Vac, 50/60 Hz turns-ratio tester without a
The general term "ATRT-03 52" or "ATRT" is used in this manual to refer to any of the ATRT-03 52 models. Any differences are clearly described where applicable. The ATRT-03 52 determines the transformer turns-ratio using the IEEEC57.12.90 measurement method. The ATRT-03 52 outputs an excitation test voltage to the transformer's primary windings. The induced secondary voltage is sensed and the transformer turns-ratio is calculated. The unit can measure turns-ratios from 0.8 to 15,000. The transformer turns-ratio, excitation current, and phase-angle readings are displayed on the large back-lit LCD.The built-in transformer type detection feature allows the ATRT-03 52 to detect and test 130 transformer types defined by ANSI, CEI/IEC and Australian standards. The ATRT-03 52 can be used as a stand-alone unit or can be computer-controlled. It can be operated locally using its alpha-numeric keypad and rotary switch. Information is displayed on a back-lit LCD screen (64 x 128 dot graphic) that is viewable in both bright sunlight and low-light levels. Test reports can be printed in the field on the unit's built-in 4.5-inch wide thermal printer (ATRT-03 52 and ATRT-03A 52 only). The ATRT-03 52 can store up to 112 test records and 128 test plans in Flash EEPROM. Test records or test plans can be stored or transferred to and from a PCvia the available interfaces (R5-232C port, USB port, USB Flash drive port).
E':'User Interface
REV 2
The ATRT-03 52 features a back-lit LCDscreen (64 x 128 dot graphic) that is viewable in both bright sunlight and low-light levels. The test results screen displays the transformer turns-ratio, excitation current, phase angle, and percentage error. The unit is controlled via a rugged, 16key, membrane keypad and a digital rotary switch.
Computer Interface
In computer-controlled mode, the unit can be controlled via the RS-232C or U5B port using the supplied PCsoftware (Transformer Turns-Ratio Analyzer application provided with each ATRT03 52). This Windows® XP/Vista-based software can be used to run a test and to store test results on a Pc. Test results can also be exported to Microsoft" Excel.
REV 2
1.2
Technical Specifications
Table 1. ATRT-03 $2 Technical Specifications
TYPE PHYSICAL SPECIFICA TlONS METHOD OPERA TlNG VOL TAGE MEASUREMENT TURNS-RATIO Portable, lightweight, automatic, 3-phase transformer turns-ratio meter 18"W x 7"H x 15"D (45.7 em x 17.8 em x 38.1 em); Weig ht: 20 lbs (9.0 kg) 100 - 240 Vac, 50/60 Hz ANSI/IEEE C57.12.90
MEASURING RANGE
0.8 -15,000
0.8 - 1,999: ±0.1 %, 2,000 - 3,999: ±0.25%. 4,000 - 15,000: ±1 % @ 8 Vac 0.8 - 1,999: ±O.1%, 2,000 - 3,999: ±0.20%. 4,.000 - 15,000: ±1 % @ 40 Vac 0.8 - 1,999: ±O.1 %, 2,000 - 3,999: ±0.15%. 4,000 - 15,000: ±1 % @ 100 Vac 8 Vac @ 1Amp, 40 Vac @ 0.2 Amp, 100 Vac @ 0.1 Amp 0 - 2 Amperes; Accuracy: ±O.1 mA, ±2% of reading (±1 mAl 0 - 360 Degrees; Accuracy: ±0.2 degree (±1 digit) Back-I it LC D screen (64 x 128 dot graph ic display); Viewable in brig ht sunlight and low-light levels Built-in 4.5-inch wide thermal printer One RS-232C port, One USB port One USB Flash drive interface port; Up to 999 transformer test records can be stored on a USB Flash drive (not included). Windows<BlXP/Vista-based Transformer Turns-Ralio included with purchase price Analyzer application is
TEST VOL TAGES EXCITA TlON CURRENT READING RANGE PHASE-ANGLE MEASUREMENT DfSPLA Y PRINTER COMPUTER EXTERNAL INTERFACES DATA STORAGE
PC SOFTWARE
INTERNAL TEST RECORD STORAGE TEST PLAN STORAGE
Can store 112 transformer test records internally. Each record holds the test record header and up to 33 readings per phase. The readings include turns ratio readings, excitation current readings, and nameplate voltages. Can store 128 transformer test plans internally. Test plans can be transferred to the unit from the PC via the RS-232C/USB port or via the USB Flash drive interface 240Vac, 2 Amps
INTERNAL
LOAD TAP CHANGER CONTACT SAFETY ENVIRONMENT HUMIDITY (MAX) AL TlTUDE (MAX) CABLES
Designed 10 meel UL 61010A-1 and CAN/CSA C22.2 No. 1010.1-92 standards Operating: -10' to 50' C (15' to +122· F); Storage: _30· C to 70· C (-22· to +158' F) 90% RH @40' C (104' F) non-condensing
2000m (6562 ft) to fully safely specifications One 15-foot Single-phase set, One 15-foot 3-phase set, One 25-foot extension set, One safely ground, One USB, One RS-232C, One LTC cable, cable bag One year on parts and labor
WARRANTY
. The §l~o;ve,?p,e~cjf(q;ltipn?:are.'lali~·?t ominat operating.veltage.and at a n J~~.p.~rtaJ!Jr.e ?~OC (77°F.).;·S:R~Cifl~a;t~0n_~ t;if may chqngewitbQ'41~·p'r.iornotice.
"
NOTE
r~i:':
PHYSICAL
REV 2
Specifications
TEST VOLTAGES EXCITA TlON CURRENT READING RANGE PHASE-ANGLE MEASUREMENT DISPLA Y PRINTER COMPUTER INTERFACES EXTERNAL DATA STORAGE PC SOFTWARE INTERNAL TEST RECORD STORAGE TEST PLAN STORAGE
Can store 112 transformer test records internally. Each record holds the test record header and up to 33 readings per phase. The readings include turns ratio readings, excitation current readings, and nameplate voltages. The unit can store 128 transformer test plans. Test plans can be transferred to the unit from the PC via the RS-232C/USB port or via the USB Flash drive interface 240 Vac, 1 Amp Designed to meet UL 61010A-1 and CAN/CSA C22.2 No. 1010.1-92 standards Operating: -10' to 50' C (15 to +122" F); Storage: -30' C to 70' C (-22' to +158" F)
0
INTERNAL
LOAD TAP CHANGER CONTACT SAFETY ENVIRONMENT HUMIDITY (MAX) AL TITUDE (MAX) CABLES
90% RH @ 40' C (104' F) non-condensing 2000m (6562 ft) to fully safety specifications One is-foot single-phase set, One 15-foot 3-phase set, one 25-foot extension set, One safety ground, One USB, One RS-232, One LTC cable, cable bag One year on parts and labor
WARRANTY
REV 2
S2 USER'S MANUAL
,,]
S2 Technical Specifications
Portable, lightweight, automatic, 3-phase transformer turns-ratio meter 18"W x 7"H x 15"0 (45.7 cm x 17.8 cm x 38.1 cm); Weight: 20 Ibs (9.0 kg) 100 - 240 Vae, 50/60 Hz ANSI/IEEE C57.12.90 0.8 -15,000 0.8 - 1,999: ±O.1%, 2,000 - 3,999: ±0.25%. 4,000 - 15,000: ±1 % @ 8 Vac 0.8 - 1,999: ±O.1%, 2,000 - 3,999: ±0.20%. 4,000 - 15,000: ±1 % @ 40 Vae 0.8 - 1,999: ±O.1%, 2,000 - 3,999: ±0.15%, 4,000 - 15,000: ±1 % @ 100 Vac 8 Vac@ 1Amp, 40 Vac@ 0.2 Amp, 100 Vae@O.1 Amp 0 - 2 Amperes; Accuracy: ±O.1 mA, ±2% of reading (±1 mAl 0 - 360 Degrees; Accuracy: ±0.2 degree (±1 digit) Back-lit LCD screen (64 x 128 dot graphic display); Viewable in bright sunlight and low-light levels One RS-232C port, One USB port One USB Flash drive interface port; Up to 999 transformer test records can be stored on a USB Flash drive (not included). Windows'Bl XPlVista-based Transformer Turns-Ratio Analyzer application is included with purchase price Can store 112 transformer test records internally. Each record holds the test record header and up to 33 readings per phase. The readings include turns ratio readings, excitation current readings, and nameplate voltages. Can store 128 transformer test plans internally. Test plans can be transferred to the unit from the PC via the RS-232C/USB port or via the USB Flash drive interface 240 Vac, 2 Amps Oesig ned to meet UL 61 01OA-1 and CAN/CSA standards
0
MEASURING RANGE
TEST VOLTAGES EXCITATION CURRENT READING RANGE PHASE·ANGLE MEASUREMENT DISPLAY COMPUTER EXTERNAL INTERFACES
DA TA STORAGE PC SOFTWARE
INTERNAL
INTERNAL
LOAD TAP CHANGER CONTACT SAFETY ENVIRONMENT HUMIDITY (MAX) AL TITUDE (MAX) CABLES
Operating: _10 to 50" C (is" to +122· F); Storage: -30· C to 70' C (-22' to +158· F) 90% RH @ 40" C (104 F) non-condensing
0
2000m (6562 ft) to fully safety specifications One 15-foot Single-phase set, One 15-foot 3-phase set, One 25-foot extension set, One safety ground, One USB, One RS-232C, One LTC cable, cable bag One year on parts and labor
WARRANTY
T-~e:abovespecifications
NotE
a rfd~a~. a
It;"
1.3
REV 2
The ATRT-03 52, ATRT-03A 52, and ATRT-03B 52 controls and indicators are shown in Figure 1, Figure 2, and Figure 3, respectively. A leader line with an index number points to each control and indicator, which is cross-referenced to a functional description in the corresponding table. The purpose of the controls and indicators may seem obvious, but users should familiarize themselves with them before using the ATRT. Accidental misuse of the controls will usually cause no serious harm. Users should also familiarize themselves with the safety summary information found on the front page of this User's Manual.
REV 2
ATRT-03 S2} ATRT-03A 52, AND ATRT-03B 52 USER'SMANUAL Table 4. Functional Descriptions of ATRT -03 52 Controls and Indicators
~I
Item
Number 1 2
3 4 5
Panel Markings
EMERGENCY TURN OFF "PUSH"
Functional Description
Emergency turn-off test voltage switch.
Back-lit LCD screen (62 x 128 dot graphic). viewable in bright sunlight and low-light levels.
H
USB MEM
H voltage connector. USB Flash drive interface port. X voltage connector. Load Tap Changer controller connector. 4.5-inch wide thermal printer.
X
LTC CONTROL 120-240 Vac, 2A, 50-60Hz Fuse: 250Vac, SA Fast-Blow GROUND CHANGE "PUSH" TO SELECT LTC CONTROL TEST IN PROGRESS RS-232C USB PC
6
7
8
9 10
Input power connector and fused power switch with third-wire safety ground. Ground stud for connecting to sub-station ground. Control knob. You can scroll through menu items by turning the control knob. A highlighted menu item can be selected by pushing the control knob. LoadTap Changer control buttons. Rugged alpha-numeric keypad. This LED flashes in response to commands or when a test vollage is applied to the test transformer. RS-232C PC interface connector. USB PC interface connector.
11 12 13 14 15
lIt ~
REV 2
REV 2
ATRT-03 52, ATRT-03A 52, AND ATRT-03B S2 USER'SMANUAL Table 5. Functional Descriptions of ATRT-03A S2 Controls and Indicators
':;1
Item Number 1 2
3
Panel Markings
EMERGENCY TURN OFF "PUSH"
Functional Description
Emergency turn off test voltage switch.
H
USB
H voltage con nector. USB Flash drive interface port. X voltage connector Load Tap Changer controller connector. Power sWitch Input power connector with third-wire safety ground. Ground stud for connecting to sub-station ground. LED is lit when internal batteries are being charged. 12 VDC input connectors. 4.5-inch wide thermal printer,
4 5 6
7 8 9 10 11 12 13
MEM
X LTC CONTROL POWER 120-240 Vac, 2A, 50-60Hz Fuse: 250Vac, SA Fast-Blow GROUND CHARGE +12V GROUND
Control knob. You can scroll through menu items by turning the control knob. A highlighted menu item can be selected by pushing the control knob. Load Tap Changer control buttons. Rugged alpha-numeric keypad This LED flashes in response to commands or when a test voltage is applied to the test transformer. RS-232C PC interface connector. USB PC interface connector.
14 15 16 17
18
k: ,
REV 2
REV 2
ATRT-03 52, ATRT-03A S2, AND ATRT-038 S2 USER'S MANUAL Table 6. Functional Descriptions of ATRT-038 82 Controls and Indicat.ors
Item Number
1
Panel Markings
EMERGENCY TURN-OFF "PUSH"
Functional Description
Emergency turn off test vollage switch ..
2 3
4 5 6 7 H USB MEM
USB Flash drive interface port. X voltage connector. Load Tap Changer controller connector. Input power connector and fused power switch with third-wire safety ground,. Ground stud for connecting to sub-station ground. Control knob. You can.scrof through menu items by turning the control knob ..A highlighted menu item can be selected by pushing the control knob Load Tap Changer control buttons. Rugged alpha-numeric keypad.
X
LTC CONTROL
8
9
10
11
12
13 14
This LED flashes in response to commands or when a test voltage is applied to the test transformer. RS-232C PC interface connector. USB PC interface connector.
lir"
2.0
2.1
ATRT-03
REV
PRE-TEST SETUP
Operating Voltages
All three ATRT-03 52 models can be powered by ac line voltage of 100-240 Vac, 50/60 Hz. For greater flexibility, the ATRT-03A 52 features an internal rechargeable lead acid battery and can also be powered by a 12 Vdc external source. The ATRT-03 S2 has built-in ground fault isolation detection and will only operate with voltages that are ground-fault isolated.
2.2
To increase the LCD screen contrast, press and hold the [PAPER A Contrast] key for two seconds. Release the button when the desired contrast level has been reached. To decrease the LCD screen contrast, press and hold the [PAPER v Contrast] key for two seconds. Release the button when the desired contrast level has been reached.
2.3
To advance the thermal printer paper, press and release the [PAPER
Contrast] key.
To retract the thermal printer paper, press and release the [PAPER v Contrast] key.
2.4
Printer Paper
The ATRT-03 52 and ATRT-03A 52's built-in thermal printers use 4.s-inch wide thermal paper for printing test results. To maintain the highest print quality and to avoid paper jams, the use of thermal paper supplied by Vanguard Instruments Company is highly recommended. Additional paper can be ordered from the following sources:
Vanguard Instruments
Co, Inc.
1520 S. Hellman Avenue Ontario, CA 91761 Tel: 909-923-9390 Fax: 909-923-9391 Part Number: VIC TP-4 paper
BG Instrument Co.
13607 E. Trent Avenue Spokane, WA 99216 Tel: 509-893-9881 Fax: 509-893-9803 Part Number: VIC TP-4 paper
REV 2
~~::~
2.5
The ATRT-03 52 features a built-in Load Tap Changer (LTC) controller that can raise or lower the LTCtap position from the front panel. The LTCcontroller circuit uses two 250 Vac/2A, NO, relay contacts to simulate the LTC Raise/Lower switches. Each relay contact is protected by a 1A/250 Vac fuse (5 X 20mm, fast acting). The fuse should be replaced with a Littlefuse PIN 217001 or equivalent. Follow the instructions below to replace the LTCcontroller fuses: a. Remove the ATRT-03 52 from its casing by removing the four screws from the bottom of the case:
Ir:,
REV 2
b. The LTCcontrol board is located under the left side of the front panel as shown in the figure below. Flip the unit over to easily access the LTCcontrol board fuses.
c. d.
Replace any fuses as necessary with Littlefuse PIN 217001 or equivalent (250 Vac/lA, X 20mm fast-acting type). Re-secure the unit in its casing with the screws that were removed in step a.
REV 2
"::1
3.0
OPERATING PROCEDURES
The ATRT-03 52 should always be grounded with the provided ground cable before connecting H and X cables. The transformer bushings should also be grounded before connecting test leads to the transformer. This will prevent inducing any voltages into the ATRT-03 52. All transformer bus connections must be removed, and the transformer must be isolated before performing any tests. Typical transformer connection diagrams are illustrated in the sections below.
3.1
Connection Diagrams
r'
1\,.. "
LOWER
REV 2
CS
L LOWER
R
RAISE
REV 2
- ...::1
(X2) (X1)
(XO)
(X3)
to a Oelta-Wye Transformer
I1r~ .
r
REV 2
m~~~:-..2X~1~ III
II.
III • II.
H1
III~~
REV 2
-"
::J1
L._I_._
SERIES WINDING
_._._ ..._.
R
LOAD H1
~ RAISE_._._._j X1
I . I
COMMON
H2
{: ,,"
REV 2
X1
H2
Current Transformer
(CT)
~e'f~£Qr;
REV 2
,if
H2
IIr,"
_.---..
,ATRT-03
H1
HZ
REV 2
~I
H2
"B"PHASE BUSHINGCT
I ..__.......,~......;..;:....o
1._,
I I
H2
JUMPER "A" PHASE CABLE
"c" PHASE
JUMPER
CABl.E
~I':
ii,,, '
REV 2
H3 H2
HO
X1
H1 -
.,•
X1
X1
NOTE
REV 2
'"~~
3.2
The ATRT~03 S2 offers three test voltages, 8 Vac, 40 Vac, and 100 Vac. The unit always defaults to 40 Vac at power-on. The 8 Vac test voltage is for testing transformers which require low test voltages, such as metering Current Transformers (C1's). For metering C1's, higher voltages may drive the C1's into saturation, thus giving invalid results. The 40 Vac test voltage is recommended for testing power transformers. The 100 Vac test voltage is recommended for testing power transformers in noisy environments. Follow the steps below to set the test voltage: a. Turn on the unit and start from the "START~UP" menu: 1. RU~~ TEST 12. SETUP -.:; TEST PLANS I 4. II r AGt~OS;T C TH1E: DATE:
11:23:,01
07/20 .... ·10
~:ECORD ID TESt VOLTAGE I 7: PRINT RECORD _'. 4. SAVE/~~ESTORE RECORD TIME ..J. ::;ET
1.
.
....... .4..
C'
ATRT-03B S2
~;""
ATRT~03 52, A~RT~03A 52, AND ATRT-03B 52 USER'S MANUAL: c. The following screen will be displayed:
REV 2
1. 8 VOLTS
Select the desired test voltage by pressing the corresponding ([1 J, [2], 0 r [3]). d. The voltage will be set and the following confirmation
40 VOLTS SET
...
REV 2
~
;'1
.. \<
3.3
12.
H: 23: 81 87/28/18
Press the [2] key (SETUP). b. The following screen will be displayed:
Press the [5] key (SET TIME). c. The following screen will be displayed:
.:>
ENTER DATE
Mt1-DD- vv
Enter the date using the alpha-numeric d. The following screen will be displayed:
keypad.
ENTER TIME
HH.:MI"'1: SS
Enter the current time using the alpha-numeric keypad. When the complete time has been entered, you will be immediately returned to the "START-UP" menu.
[~'
REV 2
3.4
Performing Tests
12"
DATE:
Press the [2] key (SETUP). b. The following screen will be displayed:
I 1.
'I 1. RECORD ID
2. TEST VOLTAGE 3. DISPLAY RECORD 4,. SAVE/RESTORE RECORD 5. SET TIME
ATRT-03 5,2 and ATRY-03A S2 Press the [1] key (RECORD /0).
ATRT-03B 52
j/J_ TO POSITION
"EtHER"
Ttl ACCEPT
keypad.
When pressing a key, the corresponding number on the key will be displayed first. Pressing the key again will display the first letter on the key. Pressing the key again will display the second letter on the key. For example, to type the letter "A", you must press the [,2] key twice. To erase the character at the cursor position, press the [CLEAR] key. Press the [PAP'ER 1\ Contrast] key to move to the next character. Press the [PAPER
REV 2
--, "j
v Contra.st] key to move to the previous character. Press the [ENTER] key when you
are done typing the company name. d. The following screen will be displayed:
STATION:
CIRCUIT:
~1A~~UFAC;TURER :
fL. ,
t'10DEL:
REV 2
i/J..
TO PO~:ITlot~
..E~HEF~" TO ACCEPT
Type the transformer's model information press the [ENTER] key. h. The following screen will be displayed: SER I AL NUt1BE~::
i/J..
.TO POSITION
"Et·nER"
TO ACCEPT
I<VA F!.ATING:
T..... J..
TO POS;ITIot~
"Et'HER"
TO ACCEPT
REV 2
_.',::I]
j.
j/1 TO POSITlm~
[~,2, '
11,
REV 2
TIt1E: DATE:
15: 45: 15
07"'20/10
Press the [1] key (RUN TESn. b. The following screen will be displayed:
XFt'1R CO~lFI G:
1. SIt~I3LE PHASE
2. Dy
'ld 4. Dd
..... 111
C"
..... Yy
E.• t·lE:"':T PAGE Press the [1] key (SINGLE PHASE). c. The following screen will be displayed: NAME PLATE VOLTAGE? 1. YES
2.
no
re;~~
key if
YO_W .Wo:~J.di e-to use Hi~":i1a·riie'p[~re-~olb~&~' I ~aJuesJrom :R.~;t~ :~opl~n:((e.tot~p; d. ... ~~~~'" s .
REV 2
J~l
name plate
1. YES
Press the [1] key (YES) if you would like to enter the transformer voltage values. The following screen will be displayed.
Type the H winding name plate voltage value using the numeric keypad. The screen will be updated as shown below:
2,4013
Type the X winding name plate voltage value using the numeric keypad. The screen will be updated as shown below:
2,400
240
Press the [2] key (NO) if you do not want to enter the transformer voltage values. Continue to step d.
name plate
~~"'
REV 2
"STAF<~T" TO TE:3T
OR
"STOP" TO ABORT
Press the [START] key to initiate the test. e. The following screen will be displayed while the test is being performed:
The test results will be displayed on the LCD screen when testing has finished:
RATIO
MA
XDIFF
+10.004 0004
0.04
The polarity is displayed as either a plus sign (+) for "in-phase" or a minus sign (-) for "out-of-phase", The value listed under "% DIFF" is the percentage error.
,N)J]E Press any key to continue. If using an ATRT-03 52 or ATRT-03A 52, continue to step f. If using an ATRT-03B 52, continue to step h.
35~
,~
REV 2
52 USER'S MANUAL
.:.~
\I~
f.
RESULTS?
HO
Press the [1] key (YES) to print the test results. g. The following screen will be displayed:
PRIHT FORt'1AT? 1. COLUl'1t·~
2. DETA.I LED
Press the [1] key (COLUMN) to print a columnar report (see Figure 16) or press the [2] key (DETAILED) to print a detailed report (see Figure 17). h. The following screen will be displayed:
Press the [1] key (YES) to save the reading. i. The following screen will be displayed:
TEST
SAVED
t!;!"~:::,
ATRT-03
REV 2
TEST SAI,lED
j.
1. 'E~=; 2. ~W
I. ..
.,.. •
TEST
REV 2
11.
RECG.RD?
Press the [1] key (YES) to save the test record to the unit's Flash EEPROM.
I.
PLEASE
WAIT •••
RECORD NUMBER 1
U rnhieri't:tl'lctwjllnot
o\tg~v.mitej
11=~,;:::::'f.~_=
Press any key to return to the "START-UP" menu.
r;:.
REV 2
TRANSFORMER
==MF"'O=Or...JY ; 5>T_.:X: Or...J ; C:X:~CLJ:X:T .... MF~. MOOE.L=
TEST
RESULTS
T:J:ME.=.1..S;53:ze
2J---
S;:X:r...J~LE.
p~_S;E.
S_N. KV_
RTG;
.1..Z34=~~e90 .1..0
H_:X:
O ..... ER_TOR.
~.1..
~z
X.1..------
I-t
'AF". TAP.
_ _
VCL..,ACiOE.
lJOL,":"C:;;E:.
><
><
PHS
A
M_RFoTZO
..... 10_ 00_
mAl
__
Figure 16. Single Phase Test Results Printout - Column Format (ATRT-03 52 and ATRT-03A 52 only)
Test record date and time. Test record header information (see section 3.4.1). Test voltage. Type of transformer H tap voltage. X tap voltage, Calculated ratio. Percentage error between the calculated ratio and the measured ratio. Excitation current. Measured ratio. Winding polarity. under test
3
4
5
6 7
B
9
10 11
39:)
REV 2
2l
~
t--_T_R_A_N
J
--;J~l' ... -,
----0
~
~. =::r
""",
:J: l::J1'J
T
'~C::LJ::J:
MFR.
MODEL,
~ __ r--..:I -: RTl::i """ • l::JR' 10< ........""" l::JF" E ~ TEST
~:J:NGLE :L 2
.10
=_~
_FCJRI"""IER
H"""X 4C>
........ OLTAG,E
........... 01 .....
-----------=-----0
~=====i------Q
\::.J
F"_""'~E
1-i2
.....OL.,T·AGE.
TAP SETT;I:NG.
F;"=,,,""" Z '0
10_
OCOO"
_AT
Z 0.
It.
Item Number 1 2 3
4
ATRT-03
REV 2
Table 8. Descriptions of Single Phase Test Results Elements (Detailed Format) Description
Test record date and time. Test record header information (see section 3.4.1). Test voltage. Type of transformer H tap voltage. X tap voltage. Calculated ratio. Measured ratio. Percentage error between the calculated ratio and the measured ratio. Measured transformer turns ratio. Measured voltage ratio. Winding phase angle. Excitation current under test
5 6 7
8 9
10
11 12 13
,,]lI
I 1. RUt·~ TEST
4. DIAG~WSTIC DATE:
TH1E:
3. TEST PLAt~S
2. SETUP
07/20/10
15: 45: 15
Press the [1] key (RUN TESn, b. The following screen will be displayed:
E••
Yy NE::<T PAGE
Press the [2] key (Oy). c. The following screen will be displayed:
2. uo
X0 ACCESSIBLE? 1. YE:3
T· ~
__
'~I
.
I '
'
,
u"
Iff.
I
1. Dyn 1 2. Dyn3
3. Dyn5
ATRT~03 52, ATRT~03A 52, AND ATRT-038 52 USER1S MANUAL, d. The following screen will be displayed:
REV 2
4. 5. 6. 7.
Press the [1] key (Oynl). e. The following screen will be displayed:
1.
YES
Press the [1] key (YES) if you would like to enter the transformer voltage values. The following screen will be displayed.
name plate
Type the H winding name plate voltage value using the numeric keypad. The screen will be updated as shown below:
2,40(1
REV 2
:,:'tifj
Press the [ENTER] key. The screen will be updated as shown below:
Type the X winding name plate voltage value using the numeric keypad. The screen will be updated as shown below:
:;<
": 208
Press the [2] key (NO) if you do not want to enter the transformer values. Continue to step f. f. The following screen will be displayed:
"STOP"
TO ABORT
Press the [START] key to initiate the test. g. The following screen will be displayed while the test is being performed:
L._
ATRT-03 S2, ATRT-03A S2, AND ATRT-03B ~2 USER'S MANUAL The screen will be updated with the Phase A test results as shown: TEST RESULTS:'
REV 2
RATIO
mA
A +1.810.04 8002
XDIFF' 0.11
XFf1R TYPE:
Dyn .1
Testing will continue, and the screen will be updated with the Phase B test results as shown: TEST RESULTS: F(~A,TIO MA %DTFF
Finally, the screen will be updated with the Phase C test results as shown:
TEST RESULTS:
RiATTO
MA .%DIFF
0.09
0.11 8.12
Press any key to continue. If using an ATRT-03 52. or ATRT-03A 52, continue to step h. If using an ATRT-03B 52, continue to step h. The following screen will be displayed:
J.
. 2.
11 ..
NO
45
-
REV 2
I.
_J
1. COLUMN 2. DETAILED
Press the [1;] key (COLUMN) to print a columnar report (see Figure 18) or press the [2] key (DETAILED) to print a detailed report (see Figure 19). j. The following screen will be displayed:
1. 'YES
2., HO
Press the [1] key (YES) to save the reading. k. The following screen will be displayed':
TEST SAVED
I.
12.
!IF'
~...
ATRT~03 52, ATRT~03A S2, AND ATRT-03B 52 USER'S MANUAL m. The following screen will be displayed:
REV 2
RECORD?
".'
Press the [1] key (YES) to save the test record to the unit's Flash EEPROM. n. The following screen will be displayed momentarily: SAV I t~G RECORD~••
REV 2
J
....
TRANSFORMER
Co=JM!='F"'lNY = STAT:J:ON. C:J:RCLJ:J:. = MFR.
MClClE'S __ N: •
TEST RESULTS
T :J:ME
:3!5
E------iG)
2
_BC
DYN 12:34!5~7B90 !5C>0 t-tA :J:
VC)'- • "",,(3E
O!::jlr->.:L
..
4<::>
..
e-e
.:L
D8r>1
CD 0
®
6
t-t :::3
H
/\
_
0::31 _ 0::31 0::31
t-t
.:a..
X:::3
XO
..
1-12
><2
><
.-=-P._----..... _RAT:I:O
_100_ _ 1 Oel ..... 100_ A Eo
TAP.
e-e
C.".LCWL_TEO
PHS
c:::
12
Figure 18. Dyn1 Test Results Printout - Column Format (ATRT-03 S2 and ATRT-03A S2 only)
~\,-
f?;:;' .,
Item Number 1 2 3 4 5 6 7 8
9 10 11 12
REV 2
A.
Measured ratio, excitation current, phase angle, and percentage error for Phase B. Measured ratio, excitation current, phase angle, and percentage error for Phase C. Winding polarity.
- 4~ ."
REV 2
_.]
TRANSFORMER
OA~~~~~_~~~oe
COMP~~Y~ ST~TXO~! CIRCLJ:::J:.
MFR:
Tx~e.oe~~4!~9~~
~~N~~~RO FACTORy .1.20V ~l!!IIe
OVJ"'.;l
"''''0'':>
..:La34:i67"8~<::)
VCL..TIAIoGE.
""~1iIW>'
:L 2
000
-----I--{1'1
SEI'~NC;:.
.. ,.,.
><
X
OL-.Ac:;;;K. IIIOiIIIP
lE3oe:"'T",-
ll
.... ·c:o; II
"',,:, ....-rr _.
000 ... ~".2"1!S
----,j1-0
@
.....I:lLTACiiiE
T~P'
$1!!:,...,....:1t--1Cii.
so ..... -
"."""--"""f-G!)
Figure 19. Dyn1 Test Results Printout - Detailed Format (ATRT-03 S2 and ATRT-03 S2A only)
~~.: .
REV 2
Item Number
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
Test H1-H3 and X1-XO section heading. H1-H3 tap voltage. X1-XO tap voltage. H1-H3,.X1cXO calculated ratio. H1-H3, X1-XO measured ratio. H1-H3, X1-XO percentage error between-caloulated H1-H3, X1-XO transformer turns ratio. H1-H3, X1-XO voltage ratio. H1-H3, Xi-XO measured phase angle. H1-H3, X1-XO measured excitation current. Test H2-H1 and X2-XO section heading H2-H1 tap voltage. X2-XO tap voltage. H2-H1, X2-XO calculated ratio. H2-Hi, X2-XO measured ratio. H2-Hi, X2-XO percentage error between calculated ratio and measuredralio. H2-H1, X2-XO transformer turns ratio. H2-Hi, X2-XO voltage ratio. H2-Hi, X2-XO measured phase angle. ratio and measured ratio.
H2-H1, X2-XO measured excitation current. Test H3-H2 and X3-XO section heading. H3-H2 tap voltage. X3-XO tap voltage. H3-H2, X3-XO calculated ratio. H3-H2, X3-XO measured ratio. H3-H2, X3-XO percentage error between calculated ratio and measured ratio. H3-H2, X3-XO transformer turns ratio. H3-H2, X3-XO voltage ratio. H3-H2, X3-XO measured phase angle. H3-H2, X3-XO measured excitation current.
REV 2
"~ J
Press the [1] key (RUN TEST). b. The following screen will be displayed:
..,. I =1.
E:'
1. Sn4GLE PHASE 2. Dy
'j'd
"
v..
>':Ft1R Cm~FIG:
''.,.
4. Dd
"-,I.
I
.
'r'y
6. NEXT PAGE
Select a supported three phase transformer test by pressing the corresponding numeric key on the keypad {[2], [3], [4], or [5]. For this example, we will perform a Yd test (option 3). c. The following screen will be displayed:
H~j ACCE~3SIBLE?
1. I .-.
YES
t~O
""a:
F
1. Y'Nd·1 2,. Y~~d3 3. YNd5 4.'r'Nd7 5. Yt..jd9 6~. YNd 111
ATRT~03 52, ATRT-03A 52, AND ATRT~03B 52 USER'S MANUAL d. The following screen will be displayed:
REV 2
I 7.
AUTO DETECT
Press the [7] key (AUTO DETECn, e. The following screen will be displayed:
t~AME PLATE VOL T!AGE?
1. YES 2. NO
'"
"
1.
YES Press the[1) key (YES) if you would like to enter the transformer voltage values. The following screen will be displayed. name plate
, NAME PUHE
VOLTAGE:
Type the H winding name plate voltage value using the numeric keypad. The screen will be updated as shown below: NAME PLATE
VOLTAGE:
H
1,734
53'
REV 2
"t
Press the [ENTER] key. The screen will be updated as shown below:
Type the X winding name plate voltage value using the numeric keypad. The screen will be updated as shown below:
.X
11313
Press the [2] key (NO) if you do not want to enter the transformer voltage values. Continue to stepf.
name plate
f.
The following screen will be displayed while the unit determines the transformer configuration:
TESTIHG
YNdl
,54
REV 2
will start testing the tra nsformer configu rations starting with YNd 1. If is not a type YNdl, it will continue to test for the next type (YNd3, the transformer type has been determined. The screen will' be updated to indicate which configuration is currently being tested for:
TESTING
YNd3 type has been determined, the unit will start performing the test.
h. The screen will be updated with the Phase A test results as shown: TESTRESUL RATIO MA TS·: %DIFF
A +10.057 0.8
0.46
~=<Ft1RTYPE:
Y~·jd1
Testing will continue, and the screen will be updated with the Phase B test results as shown: TEST RESULTS::
RATIO
MR
XDIFF
8.46 0.34
XFMR riPE:
YNdl
REV 2
ATRT-03 52, ATRT-OlA 52, AND ATRT-038 52 USER'S MANUAL Finally, the screen will be updated with the Phase C test results as shown:
'h~J
TEST F.~ESUL : TS
RATIO
A
MA
XDIFF
0.46
0.34
13.46
Press any key to continue. If using an ATRT-03 52 or ATRT-OlA 52, continue to step i. If using an ATRT-038 52, continue to step k. i. The following screen will be displayed:
I .-,
L.
NO
t,
"
Press the [1] key (YES) to print the test results. j. The following screen will be displayed:
PRINT
1.
FORMAT"?
2. DETAILED
C:OLUt1~~
......
")
1. 'tE~;
uo
F'
I.
TEST
ATRT-03 52, ATRT-03A 52, AND ATRT-038 52 USER'S MANUAL The following screen will be displayed:
REV 2
SAVED
12.
Press the [.2] key (NO). n. The following screen will be displayed:
Press the [1] key (YES) to save the test record to the unit's Flash EEPROM. o. The following screen will be displayed momentarily:
PLEASE W'AIT•..
~I
REV 2
,:58
I},~:,." .
3.5
REV 2
memory
and the unit has not been turned memory to a test record
below to save the test results from the working can also be used to re-save a restored USB Flash Drive): a. Perform a test or restore
memory
(see section
3.5.2 and
1- RU"~ TES;T
I
..:...
"
3. TEST
4.
The following
'Z
~III
1- ~~ECORD ID
"
-<--
TEST
~/OLTACiE
I 4.
5. SET TU1E
....'.
t:'
~3ET Tlt1E
S2
ATRT-03B 52
RECORD).
REV 2
' ','~~
1. 2. 3. 4.
Press the [2] key (SAVE RECORD). If a USB Flash drive is connected to the unit, continue to step d. If a USB Flash drive is NOT connected to the unit, continue to step e. d. The following screen will be displayed:
1. SAVE
2. SAVE
1.
SA VE INTERNALL Y Press the [1] key (SAVE INTERNALL Y) to save the test record to the unit's Flash EEPROM. Continue to step e.
2.
SAVE TO THUMB DRIVE Press the [2] key (SAVE TO THUMB DRIVE) to save the test record to the connected USB Flash drive. The following screen will be displayed:
F.~EC_0fH SAVED THUt'1B DR I \"E. TO
f~;<:'
52 USER'S MANUAL
REV 2
REV 2
J.!~
,\:~
12.
1. RUN. TEST
SETUP
15: 45: 15
~:H /2~3/10
The following
I
1. RECOR~D I D
2. TE~3T VOLTAGE
3. PRIN.T
I
4.
RECORD
. 5. SET
1. 2. 3. 4. 5.
F~ECORD I D TEST VOLTAGE DISPLAY RECORD SA.'.... E/RESTORE RECORD SET TINE
ATRT-03 S2and
ATRT-03A
S2
ATRT-03B S2
RECORD).
1. 2. 3. 4.
.
I
S2 USER'S
MANUAL
REV 2
2.THUMB DRIVE
1.
Type the record number using the alpha-numeric the [ENTER] key.
63-.
REV 2
ATRT-03 52, ATRT-03A 52, AND ATRT-038 52 U5ER'5 MANUAL 1.2. The following screen will be displayed:
.Ii
~ II
Press the [1] key (YES) to print the test record. If using an ATRT-03 52 or ATRT-03A 52, continue to step 1.3. If using an ATRT-038 52, continue to step 1.4. 1.3. The following screen will be displayed:
Press the [1] key (PRINT TO LCD) to display the restored test record data on the unit's LCD screen. Continue to step 1.4. Press the [2] key (PRINT TO PRINTER) to print the restored test record data on the unit's built-in thermal printer. The following screen will be displayed:
PR.I~n FORMAT?
1. COLUt1N 2. DETAILED
Press the [1] key (COLUMN) to print the test report in columnar format, or press the [2] key (DETAILED) to print the test report in detailed format. The test report will be printed, and you will be returned to the "STARTUP" menu. The restored test record will remain loaded in the working memory.
1:::';
1.4.
ATRT-03 52, ATRT-03A S2, AND ATRT-038 S2 USER'SMANUAL The basic information shown: 'flM 1
HU~l TE::;TS:
REV 2
07/22/10
07:52:50
Press the [PAPER v Contrast] key, The test record details will be displayed as shown:
1
CI
'r'Hd 1
RATIO A
B
C
MH
XDIFF
Press the [STOP] key to return to the "START-UP" menu. The restored test record will remain loaded in the working memory. 2, SCROLL TO SELECT Press the [2] key (SCROLL TO SELEen to scroll through a directory of the stored test records. 2.1. The following screen will be displayed:
RECORDS "UP" DIRECTORY
TO SCROLL
..m~t·j" TO SCROLL
Hom
Fi:'.,.'S
Press the [PAPER A Contrast] button or the [PAPER v Contrast] key to display the next or previous test record, respectively,
REV 2
ATRT-03 52, ATRT-03A S2, AND ATRT-038 52 USER'SMANUAL The basic test record information will be displayed as shown:
'~\~
ttl
07/21/10 09:05
When you have located the test record that you would like to restored, press the [ENTER] key, Continue to step 1.2 on page 64.
li~·,'",
REV 2
a test record from a USB Flash drive to the ATRT-03 52's working
is inserted
TH1E: DATE:
1. PECOPD ID TE::H \·'OLTAGE "7 -,,, F'PHn F.:ECORD I 4. :=:A',iE/F.:ESTORE PECORD <= .-, SET TU1E
1. RECORD ID TEST VOLTAGE "2' DISPLAY RECORD F.:EcnRD I 4. SA'.,.'E/f':ESTORE <= ~3ET TH1E
.... ..::.
'
_o.
,_I •
S2
ATRT-03B S2
RECORD).
F.:ESTOF.:E F~ECORD 2. SAVE RECORD 3. RECORD DIRECTORY 4. EF.:A:=:E F.:ECOF.:D 5. COPY TO THUMB DRIVE
.....
_ ----------------...
REV 2
'<~,~
Press the [2] key (THUMB DRIVE). e. The following screen will be displayed:
RESTORE
Type the record number that you would like to restore using the alpha-numeric keypad. If you do not know the record number, you can first print (ATRT-03 S2 and ATRT-03A 52) or display (ATRT-03B 52) a test record directory using the instructions in section 3.5.6 and 3.5.7. Press the [ENTER] key. f. The test record will be restored to the unit's working memory and the following screen will be displayed:
•
Press the [1] key (YES) to print or display the restored test record. If using an ATRT-03 52 or ATRT-03A 52, continue to step g. If using an ATRT-038 52, continue to step h.
~~~
REV 2
Press the [1] key (PRINT TO LCD) to display the test record date on the unit's LCD screen. Continue to step h. Press the [2] key (PRINT TO PRINTER) to print the restored test record on the unit's built-in thermal printer. The following screen will be displayed:
Press the [1] key (COLUMN) to print the test record in columnar format, or press the [2] key (DETAILED) to print the test record in detailed format. The test record will be printed, and you will be returned to the "START-UP" menu. The restored test record will remain loaded in the unit's working memory. h. The basic information about the restored test record will be displayed as shown below:
YHdl
~lUt'1 TESTS:
07/22/10
1 07:52:50
REV 2
ATRT-03 52, ATRT-03A 52, AND ATRT-038 52 USER'SMANUAL Press the [PAPER v Contrast] below: 1 'flM 1 key. The test record details will be displayed as shown
'"1
Press the [STOP] key to return to the "START-UP" menu. The restored test record will remain loaded in the working memory.
~r.'
REV 2
I 2.
1. F.~UH TEST
Press the [2] key (SETUP). b. The following screen will be displayed:
1. RECOF.:D ID 2. TE:=:T VOLTAGE 3. PF.:INT F.:ECORD RESTORE RECORD I 4. SAVE ..... "_, .. SET TINE
I::"
<:C "_',I.
ATRT-03 52 and ATRT-03A 52 Press the [4] key (SAVE/RESTORE RECORD). c. The following screen will be displayed:
ATRT-03B 52
1. F:ESTORE RECORD 2. SA'·/E F.:ECORD 7 -'. RECOF.~D III RECTOF.~'l 4. EF:A::E RECORD 5. COP\' TO THUNB DRI\IE
REV 2
~']
,~~
COpy REe TO THUMB DRV i.COPY SINGLE RECORD 2.COPY ALL RECORDS
1.
COpy SINGLE RECORD Press the [1] key (COpy SINGLE RECORD) to copy a single test record from the ATRT-03 S2's Flash EEPROM to the connected USB Flash drive. The following screen will be displayed:
Type the record number using the alpha-numeric keypad and then press the [ENTER] key (If you don't know the record number, you can first print or display a test record directory using the instructions in section 3.5.6 and 3.5.7, respectively). The test record will be copied to the USB Flash drive and the following screen will be displayed:
Press any key to return to the "START-UP" menu. 2. COpy ALL RECORDS Press the [2] key (COpy ALL RECORDS) to copy all test records from the ATRT-03 52's Flash EEPROM to the connected USB Flash drive. All test records will be copied from the unit to the connected USB Flash drive. The following screen will be displayed when the process is finished:
r'.~::
REV 2
REV 2
.]
I L.
'-.
1. RUN TEST
SETUP TE:3T PLAN::; D IAGt40ST rc
2'
....'11
4.
TIME: DATE:
15: 45: 15
~7/20/10
Press the [2] key (SETUP). b. The following screen will be displayed:
1. REC:ORII
I ....
.:L.1t
"')
2'
4.
E:'
..•. .1.
.' ,
..
RECOF<~D
2'
_'.
..
4. 5.
..
".'
ATRT-03852
If using an ATRT-03 52 or ATRT-03A 52, continue to step c. If using an ATRT-03B 52, continue to step d.
if;'. ,_
/
I
REV 2
Press the [1] key (PRINT TO LCD) to display the test record date on the unit's LCD screen, Continue to step d. Press the [2] key (PRINT TO PRINTER) to print the restored test record on the unit's built-in thermal printer. The following screen will be displayed:
Press the [1] key (COLUMN) to print the test record in columnar format, or press the [2] key (DETAILED) to print the test record in detailed format, The test record will be printed, and you will be returned to the "START-UP" menu. d. The basic information about the restored test record will be displayed as shown below:
YNd1
REV 2
ATRT~03 52, ATRT~03A 52, AND ATRT-03B 52 USER'S MANUAL Press the [PAPER v Contrast] below: 1 YNd 1
,.,\,]
S ~..'OLTS RATIO
MA 0.S
%DIFF
0.46
'0.34
0.46
Press the [STOP) key to return to the "START-UP" menu. The restored test record will remain loaded in the working memory.
Ii.',
..
_
~~ I
REV 2
3.5.6.
Follow the steps below to print a directory of the test records stored in the unit's Flash EEPROM or on a connected USB Flash drive (ATRT-03 52 and ATRT-03A 52 only): a. Start from the "START-UP" menu:
12,.
4.
nIAGNOST r C
TIME: DATE:
Press the [2] key (SETUP b. The following screen will be displayed:
4. SA\i1E'/RESTORE RECORD .. 1
5. SET TIME
RECORD),
i, 'RESTORE RECORD .2. SAVE RECORD. I 3.RE:CORD iHRECTORY 4 -. ERASE RECORD . 5. COpy TO THUMB DRIVE
Press the [3] key (RECORD DIRECTORy) If a USB Flash drive is connected to the unit, continue to step d. If a USB Flash drive is NOT connected to the unit, continue to step e.
REV 2
;' 'J~
1. INTERNAL DIRECTORY
1.
INTERNAL DIRECTORY Press the [1] key (INTERNAL DIRECTORY) to print a directory of the test records stored in the unit's Flash EEPROM. Continue to step e.
2. THUMB DRIVE DIR Press the [2] key (THUMB DRIVE DIR) to print a directory of the test records stored on the connected USB Flash drive. A full directory of the test records stored on the USB Flash drive will be printed and you will be returned to the "START-UP" menu. Please see Figure 20 for a sample thumb drive directory printout. e. The following screen will be displayed:
DIRECTOR',{,
1. FULL DIRECTORY
Press the [1] key (FULL DIRECTORy) to print a full directory listing. This option will print all test record headers. The full record directory will be printed and you will be returned to the '/START-UP" menu. Press the [2] key (SHORT DIRECTORy) to print a short directory consisting of the last twelve record headers. The short record directory will be printed and you will be returned to the IISTART-UPIImenu. Please see Figure 21 for a sample internal Flash ERRPROMtest record directory printout.
In ,
.-
REV 2
,- t-I LJ .-.
f---t:LJr-1e
E3: ,
C)~
.........
c)I
14-
R , == , 03
OA.E:: '-YPE
~EC_OOO
MODEL S __ N
KV"",
R,-
(:3;
::3
...... e __ .::I......O
ReC~oO 07'" : 52
::L
:
50
TYPE
YN=l1 OF' T
, ,
TES'S
::L
,
::3
K"-""'"
RTG
Figure 20. Typical USB Flash Drive (Thumb Drive) Test Record Directory Printout
,- E:~'
,
,Y_E
;
C)
I ,
RE:C=::.
07'"
CJRY
=
5=
REC::ClRe> NUMBER 07 DA,E __ ,IMe Y N=I::L OF" NUI'""1BER ST_' ICl'" c:: I RCU IT f"1FR
50
TI=:S"'-~
.:L
=
:
, r-1C1c>E'LS __ N
:
K"-""'"
RTG
RECORD
07
4-4-
3.s
::L
= =
R.G
::1.-4- :
"'5 ""'
35
,
=
, ,
MODEL S __ N
=
RTG: 3 NLJr-IBeR 07 ME z NC3'-E OF e
:
K"-""'"
s: .:I.__~.1..___..:1..C) PH_SE
SI
TeSTS
09= OS ><F=ORf"1E'R
37"
MODE''S __ N :: KV"",
,
~TG e :3
Fi ure 21. Typical Internal Flash EEPROM Test Record Directory Printout
S2 USER'S MANUAL
_.
3.5.7. Viewing a Test Record Directory on the LCD Screen (ATRT-038 52 Only)
Follow the steps below to view a directory of all the test records stored in the ATRT-03B 52's internal Flash EEPROM: a. Start from the "START-UP" menu:
1. RUN TE!:H
TH1E: DATE:
Press the [2] key (SETUP) b. The following screen will be displayed:
!::"
~_I III
RECORD).
RECORD :::AVE RECORII 7 '. RECOF:D D I F~ECTOR'y' 4. ERASE R:ECORD ~'. COpy TO THUMB DRIVE
.-, L.
!::"
1. RESTORE
DIRECTORY}.
RECORDS
DIRECTORY
Press the [PAPER A Contrast] or [PAPER v Contrast] key to scroll through the test record directory. The test record header will be displayed as shown:
IIli'
---
REV 2
09:07
You can continue to scroll through the record directory by pressing the [PAPER A Contrast] and [PAPER v Contrast] keys. Press the [STOP] key to return to the "START-UP" menu.
REV 2
52,
..
JII
1. RUt·~ TEST
SETUP PLAH::: D I Am·mST rc 15: 45: 15 ~)7/20/10
3. TEST
4.
TIt1E: DATE:
Press the [2] key (SETUP). b. The following screen will be displayed:
--::.
1. RECORD
..:....
'7 _"
I 4.
C' ...... 1.
ATRT-03B 52
RECORD).
I 4.
3. RECORD D I RECTOR'y'
ERASE RECOF.:D
Press the [4] key (ERASE RECORD). d. The following screen will be displayed:
EF.:ASE F.:ECORD 1.ERASE 2.ERASE SINGLE REC. ALL RECORDS TO £::OT
":3TOP"
EC ' ~
1
ATRT ~0352, ATRT -03A 52, AND ATRT ~03B52 USER'S MANUAL'
REV 2
I
"-
..~.~.' ..
--._
Press the [1] key (ERASE SINGLE REe) to erase a single test record from the unit's inte rna I Flash EEPRO Th e followi ng screen wi II be displayed: M.
ERASE
RECORD ~lUt'1BER:
Type the record number that you would like to erase using the alpha-numeric keypad and then press the [ENTER] key. If you do not know the test record number, you can first print or view a test record directory using the instructions in sectio n 3.5.6 and 3.5.7, respectively.
------------_.
__ ...__ ._._-_.
REV 2
ATRT-03 52, ATRT-03A 52, AND ATRT-038 52 USER'SMANUAL The following screen will be displayed while the record is being erased:
ERAS I t"lG RECORD PLEASE ~~AIT •••
'
.lD
't,'(•
The following screen will be displayed when the test record has been completely erased:
RECORD NUt'1BER :3 E~:AS;ED !
Press any key to continue. You will be returned to the beginning of step d. 2. ERASE ALL RECORDS Press the [2] key (ERASE ALL RECORDS) to erase all the test records from the unit's internal Flash EEPROM"The following warning screen will be displayed:
ERASE ALL RECORDS! ARE "T'OU SURE? "EHTER"
TO
co-rr I t~UE.
You can press the [STOP] key to cancel the process and return to the "START-UP" menu" Press the [ENTER] key to proceed with deleting all the test records from the unit's Flash EEPROM"The following screen will be displayed during the erasure process:
E~~A:::I t"m RECO~:DS PLEASE WAIT •••
~~~:r'
52 USER'5 MANUAL
REV 2
The following screen will be displayed when all test records have been completely erased:
RECOF.:DS EF.:ASED!
REV 2
JI
port, and then start
1- RUt·j TEST
r;>
..:...
3. 4.
ouosr
TIt1E: DATE:
07/20 .. /1(1
15: 45: 15
Press the [2] key (SETUP). b. The following screen will be displayed:
1. ~.
L.
I 4.
3.
5.
PECOF.:D ID TE:3T VOLTAGE PRIHT F£CORD S A\·'E.""F.: EST ORE RECOFm SET Tlt1E
1- RECORD ID
'-1
TEST
3R DISPLA'(
A TRT -03 S2 a nd A TRT -03A S2 Press the [4] key (SAVE/RESTORE c. The following
ATRT-038
S2
RECORD).
I 4.
0::-
~ii
;J .:
.~'",'
ATRT-03 52, ATRT-03A S2, AND ATRT-038 52 USER'S MANUAL' d. The following screen will be displayed:
REV 2
DRV REe).
ERASE RECORD
I
1.
ERASE SINGLE REC. Press the [1] key (ERASE SINGLE REC.) to erase a single test record from the connected USB Flash drive. The following screen will be displayed:
Type the record number that you would like to erase using the alpha-numeric keypad and then press the [ENTER] key. If you do not know the test record number, you can first print a test record directory using the instructions in section 3.5.6 (ATRT-03 52 and ATRT-03A 52 only). The test record will be erased from the USB Flash drive and the following screen will be displayed:
REV 2
:~~
Press any key to continue. You will be returned to the beginning of step e. Press the
[STOP] key to return to the "START-UP" menu. 2. ERASE ALL RECORDS Press the [2] key (ERASE ALL RECORDS) to delete all test records from the connected USB Flash drive. The following warning screen will be displayed:
ERASE ALL THUt'lB PECORDS! APE
DRIVE
'y'OlISlIRE? TO CONTINUE.
"ENTEP"
Press the [STOP] key if you do not want to erase all the test records. You will be returned to the "START-UP" menu. Press the [ENTER] key to proceed with deleting all the test records from the connected USB Flash drive. The following screen will be displayed when all the records have been erased:
RECORDS ERASED!
---------------------
----
!~r:, '
3.6
ATRT -03 52 ATRT -03A 52, AND ATRT -038 52 U5ER 5 MANUAL·
I 1
REV 2
The ATRT-03 52 comes with the Vanguard Transformer Turns Ratio Analyzer Series 2 software (TIRA 52) that can be used to create transformer test plans on a PC (see the TIRA 52 software manual for details). Test plans can then be transferred to the ATRT·03 52 and used to quickly perform tests.
z.
07/20/H3
15: 45: 15
I
I
NOTE
Press the [1] key (LOAD TEST PLAN). If you have a USB Flash drive connected to the unit, continue to step c. I'f you do NOT have a USB Flash drive connected to the unit,continue to step d.
:1, 89]
\
""'
..
REV 2
"jil
1.
INTERNAL STORAGE Press the [1] key (INTERNAL STORAGE) to load a test plan from the unit's Flash EEPROM. Continue to step d.
2.
THUMB DRIVE
Press the [2] key (THUMB DRIVE) to load a test plan from the connected USB Flash drive. The following screen will be displayed:
Type the test plan number to load from the USB Flash drive and then press the [ENTER] key. The following screen will be displayed:
Press the [2] key (NO) to not save the test plan in the unit's Flash EEPROM and to just load it in the working memory. The test plan will be loaded in the working memory and you will be returned to the "START-UP" menu. Continue to step e to perform a test using the loaded test plan. Press the [1] key (YES) to load the test plan to the working memory and also save it in the unit's Flash EEPROM.The following screen will be displayed:
~:~
ATRT-03 52, ATRT-03A S2, AND ATRT-03B S2 USER'SMANUAL TEST PLAN 1001 SAVED!
REV 2
Press any key to continue. The test plan will be loaded in the working memory and also saved to the unit's Flash EEPROM. You will be returned to the "START-UP" menu. Continue to step e to perform a test using the loaded test plan. d. The following screen will be displayed: LOAD TEST PLAN NUt'lBER:
Type the test plan number to load from the unit's Flash EEPROM and then press the [ENTER] key. The test plan will be loaded from the Flash EEPROM and you will be returned to the "START·UP" menu. Continue to step e to perform a test using the loaded test plan. e. Start from the "START-UP" menu again to run a test using the loaded test plan from the steps above:
z.
TEST PLAt·6
4. DIAGNOSTIC TU1E:
DATE:
15: 45: 15
07/20/10
REV 2 f.
...
~cil
The following screen will be displayed (test details will differ depending on the test type defined in the test pian): TP ttl TAPS:
''"'':
.::.
YNDl
1734 1010
Set the transformer to the tap position indicated on the LCD screen. Press the [START] key to run the test using the test plan. h. The unit will start performing the test and the screen will be updated with the test results as shown: TE::;T RESULTS RATIO t~A ~1DIFF
A +H3.(i57
B C
+110.1046 +10.057
::.::n1F.:
TYPE:
vun 1
s, and
C) a "pJ/ or "FJ/will be display.ed to indicate Pass or
1
NOTE
Press any key to continue. If using an ATRT-03 52 or ATRT-03A 52, continue to step i. If using an ATRT-03B 52, continue to step k.
~IlI:"'
i.
ATRT-03 52, ATRT-03A 52, AND ATRT-D3B 52 USER'S MANUAL The following screen will be displayed:
REV 2
PRINT I 1. 'lES 2. uo
TEST RESULTS;?
I
Press the [1] key (YES) to print the test results. j. The following screen will be displayed:
2. DETAILED
FORMAT? 1. COLUMN
Press the [1] key (COLUMN) to print a columnar report or press the [2] key (DETAILED] to print a detailed report. Please see Figure 22 for a sample test results printout. k. The following screen will be displayed:
NO
Press the [1] key (YES) to save the reading. I. The following screen will be displayed: TEST S;A\·'ED
REV 2
]1
m. If the test plan included multiple tests, the start-up screen for the next test will be displayed as shown:
TAP NUMBER 2
x VTG: 240
"STAFU" TO
H VTG:
4160 RUt·~EST T
Repeat steps h through I for this test. n. The following screen will be displayed after the last defined test in the test plan has been performed: END OF TEST PLAt~
SAVE
THIS
1. 'r'E:=:
RECORD?
2. NO
Press the [1] key (YES) to save the test reeo rd to the unit's Flash EEPROM. p. The following screen will be displayed momentarily:
PLEASE L'~AIT•.•