Professional Documents
Culture Documents
INTRODUCTION
PIPE FITTINGS
OneSteel is Australias largest distributor of Pipes, Pipe Fittings, Valves and associated accessories.
The OneSteel distribution network offers more than 100 outlets throughout Australia, comprising:
OneSteel Piping Systems Capital cities and selected regional centres
OneSteel Fire Systems
OneSteel Metaland
The "Pipe Fittings" catalogue is part of a comprehensive series of catalogues, brochures and data
sheets which are provided to our customers and associated industry groups. This catalogue
describes our range of pipe fittings which are principally manufactured in carbon steel, cast ductile
iron and malleable iron. A separate catalogue describes our range of stainless steel pipes and fittings.
In Australia we have two broad groups of standards which govern the design and manufacture of our
products, viz:
British / Australian Standards
American Standards
Generally covering carbon steel and alloy steel fittings for higher
pressures and temperatures and typically used in the oil, gas,
chemical and heavy processing industries.
Our customers tend to work predominantly with one standard or the other. For your convenience we
have grouped most of the products accordingly. The detailed contents are shown on the opposite page.
For further information please contact your local OneSteel sales office. Details of our locations may
be found on our website at www.onesteel.com.au.
Our catalogues are provided for your assistance. However we are obliged to draw your attention to
the following:
OneSteel provides the information contained in this brochure as a guide only for your information.
OneSteel has taken reasonable care to ensure the accuracy of the material but you should not rely
on the whole or any part of the information. OneSteel expressly disclaims all liability whatsoever for
(including any direct or indirect loss or damage, costs or expenses howsoever incurred by any
person) or reliance on the whole or any part of the information contained in or omitted from this
brochure. OneSteel recommends that you verify any information regarding products with your
independent expert adviser and rely solely on that advisers recommendations.
CONTENTS
Introduction ..........................................................................................................................................................2
Contents ..............................................................................................................................................................3
Galvanised Malleable Fittings ..............................................................................................................................4
Galvanised Malleable Fittings ..............................................................................................................................5
Black and Galvanised Steel Fittings ....................................................................................................................6
Black and Galvanised Steel Fittings ....................................................................................................................7
Black and Galvanised Steel Unions ......................................................................................................................8
Stainless Steel Screwed Fittings BSP ..................................................................................................................8
Sealants for Threaded Joints ................................................................................................................................9
Flanges to Australian Standards ........................................................................................................................10
Flanges to Australian Standards ........................................................................................................................11
Bolting for Australian Flanges ............................................................................................................................12
Denso Corrosion Protection Systems ................................................................................................................13
Denso Corrosion Protection Systems ................................................................................................................14
Denso Corrosion Protection Systems ................................................................................................................15
Buttweld Fittings ................................................................................................................................................16
Buttweld Fittings ................................................................................................................................................17
Buttweld Fittings ................................................................................................................................................18
Buttweld Fittings ................................................................................................................................................19
OLet Fittings ......................................................................................................................................................20
OLet Fittings ......................................................................................................................................................21
High Pressure Fittings ........................................................................................................................................22
High Pressure Fittings ........................................................................................................................................23
High Pressure Fittings ........................................................................................................................................24
High Pressure Fittings ........................................................................................................................................25
Flanges to American Standards..........................................................................................................................26
Flanges to American Standards..........................................................................................................................27
Flanges to American Standards..........................................................................................................................28
Flanges to American Standards..........................................................................................................................29
Flanges to American Standards..........................................................................................................................30
Flanges to American Standards..........................................................................................................................31
Flanges to American Standards..........................................................................................................................32
Flanges to American Standards..........................................................................................................................33
Flange Gaskets ..................................................................................................................................................34
Bolting for ANSI Flanges ....................................................................................................................................35
Roll Grooved System........ ..................................................................................................................................36
Roll Grooved System........ ..................................................................................................................................37
Roll Grooved System........ ..................................................................................................................................38
Roll Grooved System........ ..................................................................................................................................39
Roll Grooved System........ ..................................................................................................................................40
Roll Grooved System........ ..................................................................................................................................41
Shouldered System ............................................................................................................................42
Shouldered
Shouldered
Shouldered
Shouldered
Shouldered
System ............................................................................................................................43
System............................................................................................................................44
System ............................................................................................................................45
System............................................................................................................................46
System ............................................................................................................................47
THREADING
UNEQUAL SIZES
When ordering Reducing Sockets, Nipples, Bushes
and Elbows, always state largest size first
e.g. 80 x 40 bush.
When ordering 3- or 4- way fittings, the sizing
sequence illustrated below should be adopted.
3
1
3
BS 1256
BS 143
20
32
32
32
20
Parallel Threaded Fitting:
Taper Threaded Pipe
32
20
= 32 x 20
= 32 x 20
FINISH
20
25
20
TESTING
Fittings shall be subject to an internal hydraulic
pressure of 2068 kPa without showing any sign of
leakage or abnormality.
32
= 32 x 20
20
= 25 x 20 x 20
10
11
14
12
19
13
15
20
21
16
22
17
18
24
23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
24
Item
Adaptor (not illustrated)
Backnut
Bend 90 M&F
Bend 90 F&F
Bend 45 M&F
Cap
Cross
Elbow 90 F&F
Elbow 90 M&F
Elbow 45 F&F
Elbow 45 M&F
Flange Undrilled
Flange Drilled
Hex Nipple
Plug Hollow.
Plug Solid
Socket
Tee
Union Flat Seat
Union Brass Seat F&F
Bush Reducing
Elbow Reducing F&F
Hex Nipple Reducing
Sockets Reducing
Tees Reducing
Tees Reducing Special
15
8
8
8
15
8
10
8
8
15
15
15
15
8
8
15
8
8
8
8
10 x 6
15 x 8
10 x 8
10 x 8
15 x 8
20 x 15
50
150
150
100
50
150
100
150
100
100
50
150
150
150
150
50
150
150
150
100
150 x 125
50 x 40
100 x 80
100 x 80
100 x 80
80 x 50
MATERIAL
kPa
kPa
kPa
kPa
kPa
kPa
kPa
*25
2070
2410
140
1030
100
1210
192
1210 100
1210
192
32
1720
2070
140
1030
100
1030
192
1030 100
1030
192
40
1720
2070
140
1030
100
1030
192
1030 100
1030
192
50
1380
1720
140
860
100
860
192
860 100
860
192
65
1380
1720
860
100
860
192
860 100
860
192
80
1380
1720
860
100
860
192
860 100
860
192
1030
1380
690
100
860
192
690 100
690
192
125
1030
1380
150
860
1030
Surface Condition
1. Black Steel: These fittings are generally degreased
and protected with a coating of light oil.
2. Zinc Protective Coating: Fittings may be supplied
zinc plated using the Electrolytic Zinc Coating
process on finished Black Fittings.
3. Hot Dip Zinc Galvanising: Galvanising of fittings
shall be performed before the thread cutting
operation, by means of the hot dip method.
4. Zinc Flake: Fittings may be supplied Zinc Flake
Coated. This process being performed on Finished
Black Fittings.
THREADING
Threads for the screwed ends of fittings comply to the
appropriate requirements of AS 1722
Part 1: Sealing pipe threads and also ISO 7-1.
Female Ends: Normally supplied with parallel thread.
Male Ends: Normally supplied with taper threads.
TYPE OF SERVICE
Nominal Water & L.P.G.
Bore of Inert Oil Med &
Pipe Med. Hvy Hvy.
Other Applications
(Inc. Steam & Compressed Air)
Fuel Oil
Medium
Heavy
Medium
Heavy
Press. Temp. Press. Temp. Press. Temp. Press. Temp.
mm
kPa
kPa
kPa
kPa
kPa
kPa
kPa
*25
3450
4140
340
1030
100
1210
192
1210 100
1210
192
32
2760
3450
340
1030
100
1210
192
1210 100
1210
192
40
2760
3450
340
1030
100
1210
192
1210 100
1210
192
50
2410
3100
340
1030
100
1210
192
1210 100
1210
192
65
2410
3100
1030
100
1210
192
1210 100
1210
192
80
2070
2760
1030
100
1210
192
1210 100
1210
192
100
1720
2070
1030
100
1030
192
1030 100
1210
192
125
1720
2070
150
1380
1720
Med. &
Hvy.
Nominal
Bore of Pipe
Med. &
Hvy.
mm
kPa
mm
kPa
*25
1030
50
1030
32
1030
65
1030
40
1030
80
1030
100
1030
100
FINISH
Other Applications
(Inc. Steam & Compressed Air)
Fuel Oil
Medium
Heavy
Medium
Heavy
Press. Temp. Press. Temp. Press. Temp. Press. Temp.
4
2
14
13
10
12
11
15
17
16
Item
Barrel Nipple
(Manufactured from heavy pipe)
80
90 Bend (M&M)
150
150
45 Bend (M&M)
15
100
Reducing Bush
8x6
100 x 80
Elbow F&F
150
Cap
100
Elbow (M&F)
100
100
8x6
100 x 80
Dia. 15
Length 100
10
11
Dia. 50
12
Plug (Hexagon)
100
13
150
14
Half Socket
150
15
Socket (Reducing)
8x6
150 x 100
16
Tee (Equal)
150
17
Tee (Reducing)
10 x 8
150 x 100
WORKING PRESSURES
RANGE
Black
SEATINGS
Zinc Coated
THREADING
Range:
Caps, Elbows 90, Elbows 45, Hex Nipples (equal and reducing), Plugs, Sockets (equal and reducing),
Tees (equal and reducing), Bushes, Unions, Barrel Nipples and Flanges.
Material:
Thread:
Pressure:
Our comprehensive Piping Package includes a variety of accessory products for use with pipes and fittings. These
include flange bolts, as well as a range of sealing materials for threaded and flanged joints. For threaded joints the most
popular materials are shown below.
PLUMBERS HEMP
26m rolls, for use with soap or any jointing paste which is compatible with the line fluid.
PLUMBERS SOAP
Principally for water use, available in 500gm bars.
THREADING
Boss Flanges not exceeding 150mm may be supplied
threaded with a parallel or taper thread in accordance
with AS 1722.
MATERIAL
This section covers flanges made from steel forgings
and plates, but AS 2129 also applies to Stainless Steel.
Forged steel flanges conform to BS 10.
RANGE
FORGED
Table D (Galv) Threaded
Table D (Black) Slip-on weld
Table E (Black) Slip-on weld & Threaded
Table H (Black) Slip-on weld & Threaded
NOM SIZE
15 -150mm
15 - 200mm
15 - 200mm
15 - 200mm
PLATE
Table D
Table D
Table H
Table H
NOM SIZE
15 - 600mm
15 - 600mm
15 - 600mm
15 - 600mm
Pressure, kPa*
Temperature, C
18
to 120
50
to 232
250
275
300
325
350
375
400
425
450
700
650
600
570
550
500
450
400
350
1 400
2 100
3 500
4 800
6 200
8 300
12 400
19 300
1 300
2 000
3 300
4 600
5 900
7 900
11 800
18 400
1 200
1 800
3 100
4 300
5 500
7 400
11 100
17 200
1 100
1 700
2 900
4 000
5 100
6 800
10 300
16 000
1 000
1 600
2 600
3 700
4 700
6 300
9 500
14 700
950
1 400
2 400
3 400
4 300
5 800
8 700
13 500
900
1 300
2 200
3 100
3 900
5 200
7 900
12 200
800
1 200
2 000
2 700
3 500
4 700
7 100
11 000
700
1 100
1 700
2 400
3 100
4 200
6 300
9 800
475
1 200
1 300
1 900
2 400
3 200
4 800
7 500
900
1 300
1 600
2 200
3 300
5 100
Maximum
hydrostatic
test pressure
kPa
1 050
1 800
2 100
3 150
5 250
7 200
9 300
12 450
18 600
28 950
Pressure, kPa*
Temperature, C
100
to 232
250
275
300
325
350
375
400
425
450
475
482
500
525
Maximum
hydrostatic
test pressure
kPa
3 500
4 800
6 200
8 300
12 400
19 300
3 300
4 700
6 000
8 000
12 000
18 600
3 200
4 400
5 700
7 600
11 400
17 600
3 000
4 200
5 400
7 200
10 700
16 700
2 800
3 900
5 100
6 700
10 100
15 700
2 600
3 700
4 700
6 300
9 500
14 800
2 500
3 500
4 400
5 900
8 900
13 800
2 300
3 200
4 100
5 500
8 300
12 800
2 100
3 000
3 800
5 100
7 600
11 900
2 000
2 700
3 500
4 700
7 000
10 900
1 800
2 500
3 200
4 300
6 400
9 900
1 700
2 400
3 100
4 100
6 200
9 700
1 200
1 700
2 200
3 000
4 400
6 900
500
700
940
1 300
1 900
3 000
5 250
7 200
9 300
12 450
18 600
28 950
10
DIAM.
RAISED FACE
DIMENSIONS
FOR LOOSE FLANGES
FLAT FACE
1.6mm
FLAT FACE
COPPER ALLOY
TABLE D
FLANGE
TABLE E
DRILLING
Blank
TABLE F
FLANGE
DRILLING
FLANGE
DRILLING
NOMINAL
NOMINAL
THICKNESS Bolt
SIZE
OD
T3
DN
mm
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
750
800
900
1000
1200
95
100
115
120
135
150
165
185
215
255
280
335
405
455
525
580
640
705
825
910
995
1060
1175
1255
1490
**
T6
mm mm
6
6
8
8
10
10
11
13
16
17
17
19
19
22
25
25
29
32
35
5
5
5
6
6
8
8
10
10
13
13
13
16
19
22
22
25
29
32
35
41
41
48
51
60
Circle
No.
Dia.
of
of
THICKNESS
OD
4
4
4
4
4
4
4
4
4
8
8
8
8
12
12
12
12
16
16
20
20
20
24
24
32
**
T6
T10
T11
mm mm
mm
mm
mm
M12
M12
M12
M12
M12
M16
M16
M16
M16
M16
M16
M16
M20
M20
M24
M24
M24
M24
M27
M27
M30
M33
M33
M33
M33
95
100
115
120
135
150
165
185
215
255
280
335
405
455
525
580
640
705
825
910
995
1060
1175
1255
1490
6
6
8
8
10
10
11
13
16
17
17
19
22
25
25
25
29
32
38
6
6
8
8
10
10
11
13
16
17
17
20
25
28
32
36
41
46
6
6
7
8
9
10
10
11
13
14
17
19
22
25
29
32
35
38
48
51
54
54
64
67
79
TABLE H
FLANGE
Bolt
No.
Dia.
Circle
of
of
THICKNESS
OD
4
4
4
4
4
4
4
4
8
8
8
8
12
12
12
12
16
16
16
20
20
20
24
24
32
T10
T11
**
T6
FLANGE
No.
Circle of
Dia.
of
SIZE
mm
mm
mm
mm
mm
mm
M12
M12
M12
M12
M12
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M24
M24
M24
M30
M30
M33
M33
M33
M36
M36
95
100
120
135
140
165
185
205
230
280
305
370
430
490
550
610
675
735
850
935
1015
1060
1185
1275
1530
8
8
10
10
11
11
13
14
17
19
22
25
25
29
32
32
35
38
41
8
8
10
10
11
12
13
15
17
20
23
28
32
37
42
47
52
57
68
10
10
10
13
13
16
16
16
19
22
22
25
29
32
35
41
44
51
57
60
67
68
76
83
95
67
73
87
98
105
127
146
165
191
235
260
324
381
438
495
552
610
673
781
857
940
984
1105
1194
1441
TABLE J
DRILLING
Bolt
4
4
4
4
4
4
8
8
8
8
12
12
12
16
16
20
20
24
24
24
28
28
32
36
40
mm
DN
M12
M12
M16
M16
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M27
M27
M30
M30
M33
M33
M33
M33
M36
M36
M39
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
750
800
900
1000
1200
TABLE R
DRILLING
FLANGE
DRILLING
NOMINAL
NOMINAL
THICKNESS
SIZE
1.6mm
FLAT FACE
1.6mm
DIAM.
RAISED FACE
T.11
DIAM.
RAISED FACE
PLATE FLANGE
SLIP ON WELD
OD
T10
DN
mm
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
115
115
120
135
140
165
185
205
230
280
305
370
430
490
550
610
675
735
850
T11
mm mm
10
10
11
11
13
13
14
16
19
22
25
32
35
38
41
44
48
51
57
11
11
12
13
14
16
17
19
23
27
30
39
45
52
58
64
71
78
92
*
T6
Bolt
Dia. Circle
No.
Dia.
of
of
R/F
mm
mm
mm
13
13
14
17
17
19
19
22
25
29
29
32
35
41
48
54
60
67
76
57
57
64
76
83
102
114
127
152
178
210
260
311
362
419
483
533
597
699
83
83
87
98
105
127
146
165
191
235
260
324
381
438
495
552
610
673
781
4
4
4
4
4
4
8
8
8
8
12
12
12
16
16
20
20
24
24
Bolt
Thickness
OD
*
T6
Dia. Circle
Dia.
of
of
R/F
mm
mm mm
mm
mm
M16
M16
M16
M16
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M27
M27
M30
M30
M33
115
115
120
135
140
165
185
205
230
280
305
370
430
490
550
610
675
735
850
57
57
64
76
83
102
114
127
152
178
210
260
311
362
419
483
533
597
699
83
83
87
98
105
127
146
165
191
235
260
324
381
438
495
552
610
673
781
16
16
19
19
22
25
25
32
35
38
38
41
48
51
57
64
70
79
92
No.
4
4
4
4
4
4
8
8
8
8
12
12
12
16
16
20
20
24
24
Bolt
Thickness
OD
*
T18
No.
Dia. Circle of
Dia.
of
R/F
mm
mm
mm
mm
mm
M16
M16
M16
M16
M16
M20
M20
M20
M20
M24
M24
M24
M27
M27
M30
M30
M33
M33
M36
115
115
125
135
150
165
185
205
240
280
305
370
430
510
585
640
735
805
19
19
22
22
25
25
29
32
35
41
44
51
60
70
79
89
98
105
64
64
76
76
89
102
114
127
152
178
210
260
311
362
419
483
572
622
83
83
95
98
114
127
146
165
197
235
260
324
387
457
527
584
673
730
4
4
4
4
4
8
8
8
8
12
12
12
16
16
16
20
20
20
SIZE
mm
DN
M16
M16
M16
M16
M20
M16
M20
M20
M24
M24
M24
M27
M27
M30
M33
M33
M36
M39
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
NOTES:
(1) All dimensions are in millimetres (mm).
(2) Only metric preferred sizes listed, except for DN 750 which is a
Non-preferred size.
* * (3) It is impractical to use flange thickness less than 12mm for
Steel Plate Flanges.
IMPORTANT: For DN 150 and DN 200 Flanges, the O.D. of pipe being used must be specified.
11
NOMINAL
TABLE E
TABLE F
TABLE H
FLANGE
No. Bolts
XOX
No. Bolts
XOX
No. Bolts
XOX
No. Bolts
XOX
SIZE
Per
per
per
per
DN
Flange
dia. x lgth.
Flange
dia. x lgth.
Flange
dia. x lgth.
Flange
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
750
800
900
1000
1200
4
4
4
4
4
4
4
4
4
8
8
8
8
12
12
12
12
16
16
20
20
20
24
24
32
M12
M12
M12
M12
M12
M16
M16
M16
M16
M16
M16
M16
M20
M20
M24
M24
M24
M24
M27
M27
M30
M33
M33
M33
M33
X
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
40 mm*
40 mm*
40 mm*
40 mm*
40 mm*
45 mm*
45 mm*
45 mm*
45 mm*
45 mm*
45 mm*
45 mm*
55 mm*
60 mm*
75 mm*
75 mm*
80 mm*
85 mm*
100 mm*
100 mm*
120 mm*
120 mm*
140 mm*
140 mm*
160 mm*
M12
M12
M12
M12
M12
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M24
M24
M24
M30
M30
M33
M33
M33
M36
M36
4
4
4
4
4
4
4
4
8
8
8
8
12
12
12
12
16
16
16
20
20
20
24
24
32
X
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
40 mm*
40 mm*
40 mm*
40 mm*
40 mm*
45 mm*
45 mm*
45 mm*
45 mm*
50 mm*
60 mm*
60 mm*
70 mm*
80 mm*
85 mm*
100 mm*
100 mm*
110 mm*
130 mm*
140 mm*
150 mm*
150 mm*
170 mm*
180 mm*
200 mm*
4
4
4
4
4
4
8
8
8
8
12
12
12
16
16
20
20
24
24
24
28
28
32
36
40
M12
M12
M16
M16
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M27
M27
M30
M30
M33
M33
M33
M33
M36
M36
M39
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
40 mm*
40 mm*
45 mm*
45 mm*
45 mm*
50 mm*
50 mm*
50 mm*
60 mm*
70 mm*
70 mm*
75 mm*
85 mm*
100 mm*
100 mm*
120 mm*
130 mm*
140 mm*
150 mm*
160 mm*
170 mm*
180 mm*
200 mm*
220 mm*
240 mm*
4
4
4
4
4
4
8
8
8
8
12
12
12
16
16
20
20
24
24
dia. x lgth.
M16
M16
M16
M16
M16
M16
M16
M16
M16
M20
M20
M20
M24
M24
M27
M27
M30
M30
M33
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
45 mm*
45 mm*
50 mm*
55 mm*
55 mm*
60 mm*
60 mm*
65 mm*
70 mm*
80 mm*
80 mm*
90 mm*
100 mm*
110 mm*
130 mm*
140 mm*
160 mm*
170 mm*
190 mm*
Length
1/4
5/16
3/8
1/2
5/8
3/4
M6
M8
M10
M12
M16
M20
7/8
1
1-1/8
1-1/4
1-3/8
1-1/2
USE
FOR
USE
FOR
Bolt
Diam.
M24
M27
M30
M33
M36
M39
12
A Quality Commitment
ENVIRONMENT
RECOMMENDED SYSTEM
Pipe lengths
Bends, Joints
Above ground
No mechanical impact
or abrasion
(To 60C)
Pipe lengths,
Bends, Joints
Above ground
Infrequent mechanical impact
or abrasion
(To 60C)
Pipe lengths,
Bends, Joints
Above ground
Frequent mechanical impact
Heavy abrasion
(To 60C)
Pipe lengths,
Bends, Joints
Below ground
Selected Backfill
(To 55C)
(To 75C)
Pipe lengths,
Bends, Joints
Below ground
Original Backfill
(To 75C)
Pipe lengths,
Bends, Joints
Below ground
Rock Backfill
(To 75C)
Below ground
(To 55C)
(To 75C)
Above ground
No mechanical impact
or abrasion
(To 60C)
Above ground
Infrequent mechanical impact
or abrasion
(To 60C)
Above ground
Frequent mechanical impact
Heavy abrasion
(To 60C)
13
COLOURTAPE SYSTEM
Denso Steelcoat 300 System comprises a selected
coloured petrolatum tape (Denso Colour Tape) and
compatible neutral coloured mastic (Denso Superlight
Mastic) which is ideally suited for small to medium
diameter pipes. No primer is necessary and
application by hand or wrapping machine is quick and
easy. The choice of tape colours gives an attractive
finished appearance and is also ideal for colour coding
when necessary. A clear adhesive tape (Denso Clear
Tape) can be utilised as an additional outerwrap to
provide plastic sealing properties and extra
mechanical protection.
14
PRODUCT DESCRIPTION
UNITS / CARTON
18
Denso Tape
36
x
x
x
x
x
10m
10m
10m
10m
10m
roll
roll
roll
roll
roll
24
18
12
9
6
x
x
x
x
10m
10m
10m
10m
roll
roll
roll
roll
36
24
18
12
Colour Tape
x
x
x
x
10m
10m
10m
10m
roll
roll
roll
roll
36
24
18
12
50mm
75mm
100mm
150mm
40
20
15
18
12
20
12
15
BUTTWELD FITTINGS
90 ELBOW (LONG)
T (STRAIGHT)
90 ELBOW (SHORT)
T (REDUCING)
45 ELBOW (LONG)
REDUCER (CONCENTRIC)
REDUCER (ECCENTRIC)
CAP
Buttweld Pipe Fittings are the recognised standard for leak-proof pipe fabrication in medium and
high pressure systems and in pipelines handling corrosive and hazardous fluids.
OneSteel carries premium quality buttweld fittings covered by major international oil and
petrochemical company approvals, and an alternative low-cost range of fittings for other
applications.
All stock carbon steel buttweld fittings comply fully with the material and manufacturing standards
detailed here, with the added advantage of .23% maximum carbon content for optimum weld-joint
integrity.
DIMENSIONAL SPECIFICATIONS
ASME B16.9: Steel buttweld fittings. Covers dimensions and tolerance of buttweld fittings 15 to 600mm.
B16.9
STRAIGHT TEES
LONG RADIUS WELDING ELBOWS, RETURN BENDS & CAPS
REDUCING TEES
45
180
90
180
ASME B16.25: Buttweld ends. Covers the preparation and design details of buttweld ends for all components of
buttwelded pipe systems.
MSS SP-48:
16
Steel buttweld fittings 650mm and larger. Covers dimensions and tolerance of long radius elbows,
tees and reducers in sizes 650 to 900mm.
BUTTWELD FITTINGS
MATERIAL SPECIFICATIONS
SEAMLESS CARBON STEEL: Buttweld fittings are made to the material specifications of ASTM A234, grades WPA,
WPB or WPC; which correspond exactly to the material specifications of seamless carbon steel pipes to ASTM A106
grades A, B, or C.
LOW TEMPERATURE FITTINGS: For low temperature applications, a wide range of fittings in materials to ASTM
A420 can be offered.
HIGH YIELD FITTINGS: On an indent basis, we offer a range of fittings having a high yield strength suitable for use
with the various grades of API 5LX linepipe.
FERRITIC ALLOY STEEL FITTINGS: For high temperatures, OneSteel offers a range of alloy fittings to
ASTM specification A335, in the following grades:
P1 - 1/2%Mo
P11 - 11/4%Cr1/2%Mo
P5 - 5%CR1/2%Mo
P12 - 1%Cr1/2%Mo
P7 - 7%Cr 1/2%Mo
P22 - 21/4%Cr1%Mo
P9 - 9%Cr1%Mo
AUSTENITIC STAINLESS STEEL FITTINGS: OneSteel stocks stainless steel fittings in ASTM grades 304L
and 316L. Other grades available to order.
WORKING PRESSURES
Buttweld fittings are designed and manufactured to standards which demand a bursting strength equal to or greater than
that of Seamless Pipe of the same material specification, nominal diameter and wall thickness, and their allowable
working pressures are equal to those shown for pipe in the OneSteel pipe catalogue. Maximum allowable working
pressures for:
CARBON STEEL FITTINGS: Equal to seamless pipes to ASTM A106, (Grade B unless otherwise specified).
HIGH TEMPERATURE (Ferritic Alloy): Fittings (Grades WP5, WP11 etc), are equal to seamless pipes to ASTM A335
of similar grade (P5, P11, etc).
LOW TEMPERATURE: Fittings (Grade WPL6-ASTM A420) are equal to seamless pipes to Grade 6 - ASTM A333.
STAINLESS STEEL: Fittings (Grades 304 and 316, also 304L and 316L) are equal to stainless steel pipes to
ASTM A312 of equal grade and schedule.
NB: Stainless Steel Fittings in Schedule 10S and 5S are not designed for applications where pressure is a prime
consideration, and the relevant standard, MSS SP43 establishes the working pressures substantially lower than those
yielded by the application of the basic formula.
QUALITY CONTROL
Buttweld fittings from OneSteel are subject to strict quality control. Manufacturers plants are visited regularly, and the
source of mother tube is verified. Test certificates are available as required. OneSteel liaises with major customers to
ensure that all fittings are obtained from sources approved by the customer or by specific industry groups.
17
BUTTWELD FITTINGS
CARBON STEEL BUTTWELD FITTINGS TO ASME B16.9, B16.28 & BS.1640
B16.9
LONG RADIUS WELDING ELBOWS, RETURN BENDS & CAPS
45
90
B16.28
SHORT RADIUS WELDING ELBOWS
& RETURN BENDS
180
90
OD
DN NPS mm
Sch.
10
Sch.
20
Sch.
30
Std.
Wt.
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
6.35
6.35
6.35
6.35
6.35
7.92
7.92
6.35
6.35
6.35
7.92
7.92
7.92
9.53
9.53
12.70
12.70
7.04
7.80
8.38
9.53
9.53
11.13
12.70
14.27
15.88
15.88
2.77
2.87
3.38
3.56
3.68
3.91
5.16
5.49
5.74
6.02
6.55
7.11
8.18
9.27
9.53
9.53
9.53
9.53
9.53
9.53
9.53
9.53
21.3
26.7
33.4
42.2
48.3
60.3
73.0
88.9
101.6
114.3
141.3
168.3
219.1
273.1
323.9
355.6
406.4
457
508
610
762
914
Sch.
40
10.31
11.13
12.70
14.27
15.09
17.48
19.05
Sch.
60
X
Stg.
10.31
12.70
14.27
15.09
16.66
19.05
20.62
24.61
3.73
3.91
4.55
4.85
5.08
5.54
7.01
7.62
8.08
8.56
9.53
10.97
12.70
12.70
12.70
12.70
12.70
12.70
12.70
12.70
12.70
12.70
Sch.
80
SAME AS X. STG.
1
11/4
1
1 /2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
30
36
1/2
3/4
180
15.09
17.48
19.05
21.44
23.83
26.19
30.96
Sch.
100
Sch.
120
Sch.
140
Sch.
160
X.X.
Stg.
15.09
18.26
21.44
23.83
26.19
29.36
32.54
38.89
11.13
12.70
14.27
18.26
21.44
25.40
27.79
30.96
34.93
38.10
46.02
20.62
25.40
28.58
31.75
36.53
39.67
44.45
52.37
4.78
5.56
6.35
6.35
7.14
8.74
9.53
11.13
13.49
15.88
18.26
23.01
28.58
33.32
35.71
40.49
45.24
50.01
59.54
7.47
7.82
9.09
9.70
10.15
11.07
14.02
15.24
16.15
17.12
19.05
21.95
22.23
25.40
25.40
A
38
38
38
47.5
57
76
95
114
133
152
190
229
305
381
457
533
610
686
762
914
1143
1372
16
47.5
19
43
22
55.5
70
25.4
29
82.5
35
106
44.5 132
159
51
184
57
63.5 210
79
262
95
313
127
414
517
159
190
619
222
711
813
254
914
286
1016
318
381
1219
470
1524
565
19
33
25.4
41
32
52
62
38
81
51
63.5 100
76
121
89
140
102
159
197
127
152
237
203
313
254
390
467
305
533
356
610
406
457
686
762
508
914
610
1143
762
914
1372
E.
Nom. Size
Std.Wt.
&
Ex.Stg. DN NPS
25.4
25.4
38.1
38.1
38.1
38.1
38.1
50.8
63.5
63.5
76.2
88.9
102
127
152
165
178
203
229
267
267
267
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
1/2
3/4
1
11/4
1
1 /2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
30
36
18
28.6
28.6
38.1
38.1
38.1
47.6
47.6
47.6
47.6
57.2
57.2
57.2
57.2
57.2
63.5
63.5
63.5
63.5
63.5
76.2
76.2
76.2
76.2
76.2
85.7
85.7
85.7
85.7
85.7
85.7
95.3
95.3
95.3
95.3
95.3
28.6
38.1
38.1
47.6
47.6
47.6
57.2
57.2
57.2
57.2
60.3
57.2
50.8
44.5
69.9
66.7
63.5
57.2
82.6
76.2
73.0
69.9
66.9
92.1
88.9
82.6
79.4
38.1
50.8
50.8
50.8
50.8
50.8
63.5
63.5
63.5
63.5
76.2
76.2
76.2
76.2
88.9
88.9
88.9
88.9
88.9
88.9
88.9
88.9
88.9
102
102
102
102
NOMINAL SIZE
DN
NPS
Large Small Large
End
End
End
100
90
80
4
100
65
50
40
125
100
90
125
5
80
65
50
150
125
100
6
150
90
80
65
200
150
8
125
200
100
80
250
200
10
250
150
125
100
300
250
300
12
200
150
100
350
300
350
14
250
200
150
Small
End
4
31/2
3
21/2
2
11/2
5
4
31/2
3
21/2
2
6
5
4
31/2
3
21/2
8
6
5
4
3
10
8
6
5
4
12
10
8
6
4
14
12
10
8
6
105
105
105
105
105
105
124
124
124
124
124
124
143
143
143
143
143
143
178
178
178
178
178
216
216
216
216
216
254
254
254
254
254
279
279
279
279
279
102
98.4
95.3
88.9
85.7
117
114
111
108
105
137
130
127
124
121
168
162
155
152
203
194
191
184
241
229
219
210
270
257
248
238
102
102
102
102
102
127
127
127
127
127
140
140
140
140
140
152
152
152
152
178
178
178
178
203
203
203
203
330
330
330
330
NOMINAL SIZE
DN
NPS
Large Small Large Small
End
End
End
End
400
16
305
350
14
305
305
300
12
305
295
16
400
250
10
305
283
200
8
305
273
150
6
305
264
450
18
343
400
16
343
330
350
14
343
330
18
450
300
12
343
321
250
10
343
308
200
8
343
298
500
20
381
368
450
18
381
356
400
16
381
356
20
500
350
14
381
346
300
12
381
333
250
10
381
324
200
8
381
600
24
432
432
500
20
432
419
450
18
432
24
600
406
400
16
432
406
350
14
432
397
300
12
432
384
250
10
432
750
30
559
533
600
24
559
508
30
750
500
20
559
495
450
18
559
483
400
16
559
900
673
36
635
750
673
30
610
900
36
600
673
24
584
500
673
20
572
450
673
18
NOTE
All dimensions are in millimetres (mm)
356
356
356
356
356
381
381
381
381
381
508
508
508
508
508
508
508
508
508
508
508
508
610
610
610
610
610
610
610
610
BUTTWELD FITTINGS
MASS
(weight)
90 ELBOWS
SIZE
mm
LONG RAD
SHORT RAD
LONG RAD
XS
STD
LONG RAD
Approx. Wt.
180 RETURNS
45 ELBOWS
XS
STD
XS
REDUCERS
SHORT RAD
XS
STD
CAPS
STD
XS
STD
XS
15
.08
.10
.04
.05
.16
.20
20
.08
.10
.04
.05
.16
.20
.07
.10
.14
.31
.40
.21
.13
.16
.10
.14
25
.15
.20
.10
.11
32
.26
.34
.17
.17
.22
.53
.69
.35
.17
.23
.14
.18
.29
.76
1.00
.50
.66
.26
.34
.18
.23
40
.38
.48
.25
.33
.23
50
.68
.91
.45
.60
.37
.49
1.36
1.85
.90
1.22
.41
.57
.27
.32
.95
2.67
3.50
1.78
2.32
.77
1.01
.41
.45
65
1.32
1.73
.88
1.14
.74
80
2.08
2.78
1.38
1.83
1.10
1.47
4.19
5.62
2.78
3.72
1.00
1.36
.64
.82
1.49
2.90
5.90
7.98
3.90
5.31
1.36
1.89
.95
1.27
90
2.92
3.96
1.93
2.61
100
3.95
5.40
2.62
3.58
1.96
2.66
7.94
10.98
5.26
7.30
1.63
2.27
1.13
1.54
125
6.67
9.34
4.42
6.21
3.31
4.63
13.47
18.96
8.94
12.56
2.77
3.92
1.91
2.59
150
10.39
15.47
6.89
10.25
5.13
7.58
20.91
31.25 13.93
20.73
3.95
5.94
2.95
4.10
200
20.87
31.34
13.83
20.68
10.34
15.42
41.91
63.50 27.94
42.00
6.49
9.84
5.00
7.30
250
36.97
49.44
24.49
32.89
18.33
24.45
66.48
10.70 14.47
9.10
11.80
300
53.98
71.22
36.06
47.17
26.99
95.26
15.01 19.78
13.60
17.20
350
69.85
91.63
46.27
61.24
34.70
45.36
26.85 35.35
15.90
20.80
400
91.17 120.20
61.24
80.29
45.36
59.88
33.11
44.0
20.00
26.30
450
116.12 153.32
77.57 102.06
58.06
76.20
26.00
34.00
500
143.79 190.06
96.16 126.10
71.67
94.35
33.00
43.00
46.00
61.00
700
87.09 114.76
244.49 323.42
326.59 432.28 217.73 287.58 162.39 215.46
750
550
600
650
174.64 230.43
BR
15
16
20
15
25
20
32
25
40
32
50
40
65
50
80
55
STD
.11
.10
.17
.15
.34
.29
.61
.53
.92
.80
1.34
1.21
2.36
2.08
3.37
3.09
XS
.16
.13
.21
.19
.42
.36
.74
.66
1.12
1.00
1.69
1.54
2.92
2.61
4.29
3.90
RUN
90
100
125
150
200
250
300
350
BR
90
80
100
90
125
100
150
125
200
150
250
200
300
250
350
300
STD
4.47
4.09
5.72
5.26
8.98
8.21
13.29
21.11
24.36
22.09
41.37
37.65
59.88
54.89
76.20
65.32
XS
5.72
5.31
7.44
6.94
4.98
10.98
19.05
17.15
34.66
31.93
53.52
49.44
75.75
70.31
92.08
84.37
19
OLET FITTINGS
WELDOLETS
Used to make full size and reducing branch connections from 6 to 750mm
from run pipes 10 to 900mm in order to:
Weldolet
Improve flow.
Assure economical, clean and strong connections.
Sockolet
Latrolet
INSTALLATION GUIDE
Less fit up time is required for Olets than for
most other fittings or fabricated connections. When proper
welding procedure is followed, the resultant cost is more
economical than constructing branch connections by any
other method.
BRANCH
PIPE
WELD
ROOT
GAP
ROOT
GAP
OR
20
45
HEADER
PIPE
ROOT
GAP
1.6mm MAX.
CONSOLIDATION
GAP
HEADER
OUTSIDE
SURFACE
OLET FITTINGS
SIZE SELECTION CHART
STANDARD WEIGHT AND EXTRA STRONG WELDOLETS
3000# THREDOLETS
STANDARD WEIGHT AND EXTRA STRONG SOCKOLETS
10
15
25 - 20
65 - 32
900 - 80
x
x
x
x
x
6
6
6
6
6
10
15
25 - 20
65 - 32
900 - 80
x
x
x
x
x
8
8
8
8
8
20
25
40 - 32
65 - 50
125 - 80
300 - 150
900 - 350
x
x
x
x
x
x
x
20
20
20
20
20
20
20
10
10
10
10
25
32
40
50
65
90 - 80
125 - 100
250 - 150
900 - 300
x
x
x
x
x
x
x
x
x
25
25
25
25
25
25
25
25
25
15 x 15
20 x 15
25 x 15
40 - 32 x 15
65 - 50 x 15
200 - 80 x 15
900 - 250 x 15
32
40
50
65
90 - 80
125 - 100
200 - 150
900 - 500
x
x
x
x
x
x
x
x
32
32
32
32
32
32
32
32
15 x
25 - 20 x
65 - 32 x
900 - 80 x
40
50
65
80
100 - 90
150 - 125
300 - 200
600 - 350
900 - 650
x
x
x
x
x
x
x
x
x
40
40
40
40
40
40
40
40
40
50
65
80
90
100
125
150
250 - 200
450 - 300
900 - 500
x
x
x
x
x
x
x
x
x
x
50
50
50
50
50
50
50
50
50
50
65
80
90
100
125
150
200
300 - 250
450 - 350
900 - 500
x
x
x
x
x
x
x
x
x
x
65
65
65
65
65
65
65
65
65
65
80
90
100
125
150
200
250
350 - 300
500 - 400
900 - 600
x
x
x
x
x
x
x
x
x
x
80
80
80
80
80
80
80
80
80
80
90 x 90
100 x 90
125 x 90
150 x 90
200 x 90
250 x 90
350 - 300 x 90
500 - 400 x 90
900 - 600 x 90
100
125
150
200
250
350 - 300
500 - 400
900 - 600
x
x
x
x
x
x
x
x
100
100
100
100
100
100
100
100
Outlet Sizes:
125, 150, 200, 250, 300,
350, 400, 450, 500, 600,
650, 750
Order to specific size
combination.
6000# THREDOLETS
SCHEDULE 160 AND DOUBLE EXTRA STRONG SOCKOLETS
20
32
65
900 - 200
x
x
x
x
15
15
15
15
25
65 - 32
250 - 80
900 - 300
x
x
x
x
20
20
20
20
40 - 32
65 - 50
250 - 80
900 - 300
x
x
x
x
25
25
25
25
40
65 - 50
90 - 80
200 - 100
500 - 250
900 - 600
x
x
x
x
x
x
32
32
32
32
32
32
50
65
90 - 80
125 - 100
200 - 150
450 - 250
900 - 500
x
x
x
x
x
x
x
40
40
40
40
40
40
40
65
80
100
125
150
250 - 200
500 - 300
900 - 600
x
x
x
x
x
x
x
x
50
80
50
50
50
50
50
50
x
x
x
x
x
x
x
15
15
15
20
20
20
20
25
65 - 32
250 - 80
900 - 300
x
x
x
x
25
25
25
25
40 - 32 x 32
65 - 50 x 32
250 - 80 x 32
900 - 300 x 32
40
65 - 50
90 - 80
200 - 100
400 - 250
900 - 600
x
x
x
x
x
x
40
40
40
40
40
40
50
65
90 - 80
125 - 100
200 - 150
450 - 250
900 - 500
x
x
x
x
x
x
x
50
50
50
50
50
50
50
RANGE OF OLETS
The following range of Olets are available:
Weldolets Thredolets Sockolets
Outlet Sizes:
65, 80, 100, 125, 150,
200, 250, 300.
Order to specific size
combination.
15mm
HOW IT WORKS
Each outlet size indicated on chart is designed to fit a number of run pipe sizes, E.G. The 15mm fitting marked
900-100x15 will fit all run pipe sizes from 100mm to 900mm. When placed on a 900mm run pipe, there will be a
maximum gap of 1.6mm between the top of the run pipe and the base of the fitting at the crotch as shown on sketch.
This gap is negligible when welding.
1.6mm MAX
GAP
900mm RUN PIPE
21
Threaded Fittings
2000 lbs
Sch. 40
3000 lbs
Sch. 80
6000 lbs
XXS
Socket-Weld Fittings
3000 lbs
Sch. 80
6000 lbs
Sch. 160
90 ELBOW
45 ELBOW
45 ELBOW
DIMENSIONAL SPECIFICATIONS
TEE
TEE
MATERIAL SPECIFICATIONS
CROSS
COUPLING
CROSS
WORKING PRESSURES
PRESSURE / TEMPERATURE RATINGS
Nominal
Pressure
Ratings
HEXAGON
HEAD PLUG
HEXAGON
HEAD BUSHING
66
93
CAP
204 232 260 288 316 343 371 399 427 427* 482* 510 538
2000 lb
13780 13573 13366 13194 13056 12918 12746 12470 11954 11299 10610 9852 8991 8130 6993 5718 4237 2928 1619
3000 lb
20670 20359 20084 19808 19602 19360 19119 18706 17948 16949 15915 14813 13504 12229 10507 8612 6373 4409 2445
6000 lb
41340 40754 40168 39617 39232 38756 38239 37412 37412 33933 31831 29627 27008 24459 21014 17225 12780 8853 4926
ROUND
HEAD PLUG
All high pressure fittings must be used within the pressure/temperature limitations of
the pipes to which they are attached.
TYPE 2
FINISH
SQUARE
HEAD PLUG
22
Fittings are normally self-coloured or phosphate-finished. Galvanised or cadmiumplated finish is available at extra cost.
TYPE 1
UNION
90 ELBOW
45 ELBOW
TEE
Hexagonal
Nipple
CROSS
90 Elbow
45 Elbow
Tee
Coupling
Half Coupling
Cap
Cross
Hexagonal Nipple
Hexagonal Plug
Round Head Plug
Square Plug
Bush
Coupling
Hexagonal Plug
2000 lb
3000 lb
6000 lb
*All conform
to 6000 lb rating*
Half Coupling
Round Head
Plug
Square
Plug
Cap
Bush
SIZE
RANGE
NORMAL
MANUFACTURE
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
Forged
Forged
Forged
Barstock
Barstock
Barstock
Forged
6-100mm
6-100mm
6-100mm
6-100mm
6-100mm
Forged or Barstock
Forged or Barstock
Barstock
Barstock
Forged or Barstock
90 ELBOW
Tee Equal
& Reducing
45 ELBOW
2000 lb
90 Elbow
45 Elbow
Tee
Coupling
Half Coupling
Cap
Cross
Coupling
Equal & Reducing
Half
Coupling
Cap
Cross
3000 lb
6000 lb
SIZE
RANGE
NORMAL
MANUFACTURE
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm
8-80mm
Forged
Forged
Forged
Barstock
Barstock
Barstock
Forged
23
8
10
15
20
25
32
40
50
65
80
90 100 125 150
SIZE 6
A
7.93 9.52 11.11 12.70 14.28 17.46 17.46 17.46 17.46 23.81 24.60 26.98 28.57 30.16 30.16
mm
Socket-Weld Fittings are designed for welding to American standard pipes (3000 lb. fittings to Sch. 80 pipe
and 6000 lb. fittings to Sch. 160 pipe). The standard does not give dimensions for socket-welding 2000 lb. fittings.
0.8C
PIPE
C
FITTING
FITTING
1.6mm
C
C
PIPE
C MINIMUM = 11/4t
BUT NOT LESS THAN 4mm
t = NOMINAL PIPE
WALL THICKNESS
SCREWED UNIONS
SOCKET-WELD UNIONS
Alternative Collar
Alternative Collar
24
Alternative Collar
PIPE NIPPLES
CLOSE-TAPER
NIPPLES
Seamless Tubular, Screwed.
Swage and Pipe Nipples can also be supplied with non-standard end connections
e.g. One End Screwed, One End Bevelled, or One End Sch. 80, One End Sch. 40.
BUTTWELD TYPE
SCREWED TYPE
PLAIN END
BEVEL END
TYPE 1
For use with Schedule 40 & 80 pipe.
REDUCER INSERT
FITTING
PIPE
TYPE 2
For use with Schedule 160 pipe.
SIZE RANGE: From 15 x 10mm to 100 x 25mm, in all standard reducing sizes.
25
SIZES 15 - 600mm
CLASS 150, 300, 400, 600, 900, 1500 & 2500
Dimensions shown are for Flanges made to the dimensional requirements of
ASME B16.5 which is the accepted American Standard for all Flanges in sizes to
600mm bore.
API 605 gives dimensions for flanges above 600mm, which are different to
MSS, BS and ASME.
26
ANSI FLANGES
ANSI FLANGES
MATERIAL SPECIFICATIONS
American Standard Pipe Flanges are manufactured in a
variety of Carbon, Alloy and Stainless Steels and selection of
a particular grade is determined by the usual criteria of
pressure/temperature requirements and corrosion resistance.
Since these factors determine pipe and fittings to be used in a
piping system, it is then necessary only to select flanges of a
similar material.
The classifications are used to group materials for Flanges Class 150
through Class 2500.
*
General
Classification
Applicable ASTM
Specification Forgings
Carbon Steel
(Refer Table page 28)
A105
A181 Class 60*
A181 Class 70
A350 Grade LFI
other grades also available
Carbon Steel
(low temp.)
Carbon Molv
(Refer Table page 28)
Chrome-Moly Alloy Steels
1/ 2 Cr 1/ 2 Mo
1 Cr 1/ 2 Mo
11/ 4 Cr 1/ 2 Mo
21/ 4 Cr 1 Mo
3 Cr 1 Mo
5 Cr 1/ 2 Mo
5 Cr 1/ 2 Mo-Si
9 Cr 1 Mo
Chrome-Nickel Stainless Steels
Type 304
Type 310
Type 347
Type 321
Type 316
H & L Grades also available
Nickel Steel
31/2 Ni.
A182-55T Grade F1
A335
A182
A182
A182
A335
A182
A335
A182
Grade
Grade
Grade
Grade
Grade
Grade
Grade
Grade
P2
F12
F11
F22
P21
F5a
P5b
F9
A182
A182
A182
A182
A182
Grade
Grade
Grade
Grade
Grade
F304
F310
F347
F321
F316
27
Tensile Requirements
Composition, %
Classes 60 and 70
Element
Carbon, max
Manganese, max
Phosphorus, max
Silicon
Sulfur, max
Class 60
415
0.35
1.10A
0.05
0.10-0.35
0.05
Class 70
485
205
250
22
18
35
24
ADetermined
ASTM A105
TABLE 1 Chemical Requirements
NOTE For each reduction of 0.01% below the specified carbon maximum
(0.35%), an increase of 0.06% manganese above the specified maximum (1.05%)
will be permitted up to a maximum of 1.35%.
Element
Composition, %
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Copper
Nickel
Chromium
Molybdenum
Vanadium
Columbium
0.35 max
0.60-1.05
0.040 max
0.050 max
0.10-0.35
0.40 maxA
0.40 maxA
0.30 maxA,B
0.12 maxA,B
0.03 maxC
0.02 maxC
485
250
30
30
187
The sum of copper, nickel, chromium and molybdenum shall not exceed 1.00%.
B The sum of chromium and molybdenum shall not exceed 0.32%.
C By agreement between the manufacturer and the purchaser, the limits for
vanadium and columbium, or both, may be increased to 0.10% and 0.05%
respectively.
PN50
CLASS 300
5110
5010
4640
4520
4380
4170
3870
3700
3650
3450
2880
2000
1350
880
520
330
PN100
CLASS 600
10210
10020
9280
9050
8760
8340
7750
7390
7290
6900
5750
4010
2710
1760
1040
650
PN150
CLASS 900
15320
15020
13910
13570
13150
12520
11620
11090
10940
10350
8630
6010
4060
2640
1550
980
PN250
CLASS 1500
25530
25040
23190
22610
21910
20860
19370
18480
18230
17250
14380
10020
6770
4400
2590
1630
PN420
CLASS 2500
42550
41730
38650
37690
36520
34770
32280
30800
30390
28750
23960
16690
11290
7330
4320
2720
FLANGES ABOVE DN 600 ARE NOT INCLUDED IN ASME B16.5 AND THE CLASS DESIGNATIONS
IN THESE LARGE DIAMETERS DO NOT IMPLY SPECIFIC TEMPERATURE / PRESSURE RATINGS
While every effort is made to ensure that correct information is provided in this catalogue, we accept no responsibility for the accuracy or
currency of data reproduced herein.
Standards and specifications are in a constant state of change and references should be made to copies of relevant standards where
current information is critical.
28
SLIP - ON FLANGES
Although recommended practice in attaching Slip-On
type flanges is to weld both at the flange hub and the
pipe end, for mild service conditions only one is
sometimes employed. In this case the weld is normally
made at the pipe end.
THREADED FLANGES
Threaded flanges are, of course, attached by screwing to
threaded pipe ends.
SOCKET-WELD FLANGES
OneSteel stocks Type B stub ends
which are used with normal slip-on weld flanges ie Lap joint backing flanges
are not required.
29
Threaded Flange
Slip-On Flange
Size
DN
NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
30
36
Dia.
of
Fig.
O
90
100
110
120
130
150
180
190
215
230
255
280
345
405
485
535
600
635
700
815
985
1170
Nominal
Size
DN
NPS
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
1/2
3/4
Dia.
of
Fig.
O
Thickness
of
Fig.
Min.
C(1)*
Y(1)*
Y(1)*
11.5
13.0
14.5
16.0
17.5
19.5
22.5
24.0
24.0
24.0
24.0
25.5
29.0
30.5
32.0
35.0
37.0
40.0
43.0
48.0
54.0
60.3
16
48
60.5
16
4
16
52
70.0
16
4
17
56
79.5
16
4
21
57
89.0
16
4
22
62
98.5
16
4
25
64 120.5
20
4
29
70 139.5
20
4
30
70 152.5
20
4
32
71 178.0
20
8
33
76 190.5
20
8
36
89 216.0
22
8
40
89 241.5
22
8
44
102 298.5
22
8
49
102 362.0
26
12
56
114 432.0
26
12
57
127 476.0
30
12
64
127 540.0
30
16
68
140 578.0
33
16
73
145 635.0
33
20
83
152 749.5
36
20
89 130.2 914.0
35
28
95 136.5 1086.0
41
32
PN150 (CLASS 900)
Length
Thick- Thru Hub
ness Thrd.
Dia.
Dia.
No.
Slip- Weld
of
of
of
of
On
Neck Bolt Bolt Bolts
Fig.
Min.
Circle Holes
C(2) Y(2) Y(2)
1
USE PN250 DIMENSIONS
11/4
IN THESE SIZES
1
1 /2
2
21/2
3
240
38.5
54
102 190.5
4
295
44.5
70
114 235.0
5
350
51.0
79
127 279.5
6
380
56.0
86
140 317.5
8
470
63.5
102
162 393.5
10
545
70.0
108
184 470.0
12
610
79.5
117
200 533.5
14
640
86.0
130
213 559.0
16
705
89.0
133
216 616.0
18
785 102.0
152
229 686.0
20
855 108.0
159
248 749.5
24 1040 140.0
203
292 901.5
26
32
35
32
39
39
39
42
45
52
54
68
NOTES:
* 1. The 2 mm Raised Face is included in thickness
C(1) and length through hub Y(1). This applies to
PN20 and PN50 Pressure Ratings.
2. The 7 mm Raised Face is not included in
thickness C(2) and length through hub Y(2).
PN100, 150, 250 and 420 Pressure Ratings are
regularly furnished with 7 mm Raised Face which
is additional to the flange thickness C(2) and Y(2).
3. Always specify bore when ordering weldneck
flanges. Bore dimensions shown opposite also
provide inside pipe diameters.
LARGE DIAMETER FLANGES ABOVE DN 600
For Blind Flanges refer to MSS SP44.
BS 3293 covers Slip-On and Weldneck but excludes
Blind Flanges.
MSS SP44 covers Blind and Weldneck but excludes
Slip-On Flanges.
BS 3293 Weldneck PN20 flange thickness, C(1), is
less than MSS SP44 equivalents.
API - 605 Dimensions for Large Diameter Flanges
vary considerably from both BS 3293 and MSS SP44
Details on request.
30
8
8
8
12
12
16
20
20
20
20
20
20
Dia.
of
Fig.
O
120
130
150
160
180
215
245
270
310
375
395
485
585
675
750
825
915
985
1170
22
22
26
26
30
26
30
33
36
42
39
45
52
56
60
68
76
80
94
4
4
4
4
4
8
8
8
8
8
12
12
12
16
16
16
16
16
16
Nominal
Dia.
No.
of
of
Bolt Bolts
Holes
16
20
20
20
22
20
22
22
26
26
30
30
33
36
36
39
42
45
45
52
54
67
4
4
4
4
4
8
8
8
8
8
8
12
12
16
20
20
20
20
24
24
28
28
Size
DN
NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
30
36
Nominal
Dia.
No.
of
of
Bolt Bolts
Holes
22
22
26
30
33
30
33
36
42
48
56
56
68
76
Size
DN
NPS
4
4
4
4
4
8
8
8
8
8
8
12
12
12
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
1/2
3/4
1
11/4
1
1 /2
2
21/2
3
4
5
6
8
10
12
14
16
18
20
24
DN
NPS
35
43
51
64
73
92
105
127
140
157
186
216
270
324
381
413
470
533
584
692
857
1022
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
NOMINAL
SIZE
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
30
36
O.D.
of
PIPE
mm
21.3
26.7
33.4
42.2
48.3
60.3
73.0
88.9
101.6
114.3
141.3
168.3
219.1
273.1
323.9
355.6
406.4
457.0
508.0
610.0
762.0
914.0
SCH.
SCH.
STD.
SCH.
SCH.
EXT.
SCH.
SCH.
SCH.
SCH.
SCH.
X.X.
10
20
30
WT.
40
60
STG.
80
100
120
140
160
STG.
205.0
257.5
307.1
336.6
387.4
434.9
482.6
581.1
730.2
882.6
15.8
20.9
26.6
35.1
40.9
52.5
62.7
77.9
90.1
102.3
128.2
154.1
202.7
254.5
304.8
336.6
387.4
438.2
489.0
590.6
743.0
895.4
342.9
393.7
444.5
495.3
596.9
746.2
898.6
206.4
260.3
311.1
339.8
390.6
441.4
489.0
590.6
736.6
889.0
303.2
333.3
381.0
428.7
477.8
574.6
876.3
198.5
247.7
295.3
325.4
373.1
419.1
466.8
560.4
13.9
18.9
24.3
32.5
38.1
49.2
59.0
73.7
85.4
97.2
122.3
146.3
193.7
247.7
298.5
330.2
381.0
431.8
482.6
584.2
736.6
889.0
Nominal
242.9
288.9
317.5
363.5
409.5
455.6
547.7
188.9
236.5
281.0
307.9
354.0
398.5
442.9
531.8
92.1
115.9
139.7
182.6
230.2
273.1
300.0
344.5
387.4
431.8
517.6
177.8
222.3
266.7
292.1
333.3
377.9
419.1
504.9
11.8
15.5
20.7
29.5
34.0
42.9
54.0
66.7
6.4
11.0
15.2
22.8
27.9
38.2
45.0
58.4
87.3
109.6
131.8
173.1
215.9
257.2
284.2
325.4
366.7
408.0
490.5
80.1
103.2
124.4
174.6
222.3
273.1
1 STOCK FINISH:
2 SPIRAL SERRATED:
FLAT FACE
RAISED FACE
LAPPED JOINT
RING JOINT
*It is necessary to modify facing dimensions in order to furnish slip-on flanges 40mm and smaller and welding neck
flanges with bores larger than Schedule 40, in sizes 40mm and smaller, for large tongue and groove facing.
31
23
OCTAGONAL
OVAL
23
RINGS
RING GROOVE
WELD NECK
SLIP-ON WELD
THREADED
32
Nominal
Pipe Size
mm
CLASS
150
CLASS
300, 400 & 600
CLASS
900
RING NUMBER
CLASS
1500
CLASS
2500
15
R11
R12
R12
R13
20
R13
R14
R14
R16
25
R15
R16
R16
R16
R18
32
R17
R18
R18
R18
R21
40
R19
R20
R20
R20
R23
50
R22
R23
R24
R24
R26
65
R25
R26
R27
R27
R28
80
R29
R31
R31
R35
R32
90
R33
R34
100
R36
R37
R37
R39
R38
125
R40
R41
R41
R44
R42
150
R43
R45
R45
R46
R47
200
R48
R49
R49
R50
R51
250
R52
R53
R53
R54
R55
300
R56
R57
R57
R58
R60
350
R59
R61
R62
R63
400
R64
R65
R66
R67
450
R68
R69
R70
R71
500
R72
R73
R74
R75
550
R80
R81
600
R76
R77
R78
R79
FLANGE BOLTS
JACKING
SCREW POSITION
PRESSURE
GAUGE
TAPPING POINTS
TYPICAL
ORIFACE PLATE
33
FLANGE GASKETS
FLANGE GASKETS
OneSteel offers an extensive range of pre-cut gaskets to suit the
flanges described in this catalogue. Our stock range mainly
comprises:
Full Face Gaskets: To suit Table D, E and H flanges to AS 2129
Ring Gaskets:
Ring Gasket
34
Spiral Gasket
Type CRIR
*Point Height
NOMINAL
PN20
(CLASS 150)
FLANGE
No.
SIZE
DN
NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
1/2
3/4
1
11/ 4
11/ 2
2
21/ 2
3
31/ 2
4
5
6
8
10
12
14
16
18
20
24
30
36
PN50
(CLASS 300)
PN100
(CLASS 600)
PN150
(CLASS 900)
PN250
(CLASS 1500)
PN420
(CLASS 2500)
NOMINAL
FLANGE
Dia. Stud
No.
Dia. Stud
No.
Dia. Stud
No.
Dia. Stud
SIZE
Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts Bolts
4
4
4
4
4
4
4
4
8
8
8
8
8
12
12
12
16
16
20
20
28
32
ins.
mm
mm
1/ 2
60
65
65
70
70
80
90
90
90
90
90
100
110
115
120
130
135
150
160
175
190
215
45
50
55
55
60
65
75
75
75
75
80
85
90
95
100
110
115
125
135
145
160
180
1/ 2
1/ 2
1/ 2
1/ 2
5/ 8
5/ 8
5/ 8
5/ 8
5/ 8
3/ 4
3/ 4
3/ 4
7/ 8
7/ 8
1
1
1-1/ 8
1-1/ 8
1-1/ 4
1-1/ 4
1-1/ 2
4
4
4
4
4
8
8
8
8
8
8
12
12
16
16
20
20
24
24
24
28
32
ins.
mm
mm
1/ 2
65
75
80
80
90
90
100
110
110
110
120
125
140
155
170
175
190
195
205
230
290
325
55
60
65
65
75
75
85
90
95
95
100
105
110
130
145
150
160
170
180
195
250
280
5/ 8
5/ 8
5/ 8
3/ 4
5/ 8
3/ 4
3/ 4
3/ 4
3/ 4
3/ 4
3/ 4
7/ 8
1
1-1/ 8
1-1/ 8
1-1/ 4
1-1/ 4
1-1/ 4
1-1/ 2
1-3/ 4
2
4
4
4
4
4
8
8
8
8
8
8
12
12
16
20
20
20
20
24
24
28
28
ins.
mm
1/ 2
80
90
90
100
105
105
120
125
140
145
165
170
195
215
220
235
255
275
290
330
355
400
5/ 8
5/ 8
5/ 8
3/ 4
5/ 8
3/ 4
3/ 4
7/ 8
7/ 8
1
1
1-1/ 8
1-1/ 4
1-1/ 4
1- 3/ 8
1-1/ 2
1- 5/ 8
1- 5/ 8
1- 7/ 8
2
2-1/ 2
ins.
mm
USE PN250
DIMENSIONS IN
THESE SIZES
8
8
8
12
12
16
20
20
20
20
20
20
7/ 8
1-1/ 8
1-1/ 4
1-1/ 8
1- 3/ 8
1- 3/ 8
1- 3/ 8
1-1/ 2
1- 5/ 8
1- 7/ 8
2
2-1/ 2
145
170
190
195
220
235
255
275
285
325
345
435
ins.
4
4
4
4
4
8
8
8
8
8
12
12
12
16
16
16
16
16
16
3/ 4
3/ 4
7/ 8
7/ 8
1
7/ 8
1
1-1/ 8
1-1/ 4
1-1/ 2
1- 3/ 8
1- 5/ 8
1- 7/ 8
2
2-1/ 4
1
2- / 2
2-3/ 4
3
3-1/ 2
mm
105
115
125
125
140
145
160
180
195
250
260
290
335
375
405
445
495
540
615
4
4
4
4
4
8
8
8
8
8
8
12
12
12
ins.
mm
DN
NPS
3/ 4
125
125
140
150
170
175
195
220
255
300
345
380
485
540
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
750
900
1/ 2
3/ 4
7/ 8
1
1-1/ 8
1
1-1/ 8
1-1/ 4
1-1/ 2
1-3/ 4
2
2
2-1/ 2
3
2- / 4
3/ 4
1
11/ 4
11/ 2
2
21/ 2
3
31/ 2
4
5
6
8
10
12
14
16
18
20
24
30
36
Raised Face height of 2 mm for PN20 & 50 and 7 mm for PN100, 150, 250 & 420 is included in dimension L (Bolt Length).
MATERIAL SPECIFICATIONS
ASTM A193 Grade B7
Standard specification for alloy steel and stainless steel bolting materials for high temperature service.
ASTM A320
Standard specification for alloy steel bolting materials for low temperature service.
Grade L7 covers alloy steel stud bolts.
Grade L4 covers alloy steel nuts to suit Grade L7 stud bolts.
35
MECH is manufactured by the largest pipe fittings manufacturer in the world, Jinan Meide
Casting Co. Jinan Meides core value of quality provides product of premium levels employing
the latest manufacturing technology. MECHs commitment to quality is reflected in the fact
that every product, even down to the smallest galmal fitting is pressure tested. OneSteel has
enjoyed a very successful twelve year relationship with Jinan Meide and their MECH product range. MECH
products are sold in over 60 countries and are world leaders both in quality and value.
Housing
Groove
Gasket
Bolt/Nut
36
1G-Rigid
25-300mm
1 - 12
1NR-Reducing Coupling
65x50 200x150mm
2 x2 - 8x 6
1N-Flexible
25 300mm
1 12
G-28-Hinged Lever
40 300mm
1 - 12
37
C-7-Outlet Coupling
40x15mm 150x50mm
1 x1/2 6x2
7110LR-Long Radius
Elbow 90deg
50 300mm
212
38
90-Elbow 90deg
25 300mm
1 12
120-Elbow 45deg
25 - 300mm
1 12
130R-Reducing Tee
50x25mm 300x250mm
2x1 12x10
240Concentric Reducer
32x25mm 300x250mm
1 x1 12x10
230-Eccentric Reducer
80x50mm 200x100mm
3x2 8x4
130-Tee
25 300mm
1 12
300-Cap
25 - 300mm
1 12
SS-10-Elbow 90deg
Stainless
25 600mm
1 24
SS-11-Elbow 45deg
Stainless
25 600mm
1 24
SS-20-Tee Stainless
25 600mm
1 24
H305-HDP Coupling
50 500mm
2 20
H307HDP to Groove
Coupling
50-300mm
2 12
39
SJ-300N-Butterfly Valve
Lever
50 300mm
2 12
SJ-300N-Butterfly Valve
Gear
50 600mm
2 24
725G-Suction Diffuser
65 400mm
2 -16
40
726-Y-Strainer
50 400mm
2 16
DCG-300-Check Valve
(Fire)
50 - 200mm
2 8
Z07-Rigid
350 600mm
14 24
7111-Elbow 45deg
350 600mm
14 24
7150-Concentric Reducer
350x150mm 600x500mm
14x6 24x20
SJ-202-Butterfly Valve
350 600mm
14 24
7110-Elbow 90deg
350 600mm
14 24
7120-Tee
350 600mm
14 24
7121-Reducing Tee
350x350x200mm 600x600x500mm
14x14x10 24x24x20
7160H-Cap
350-600mm
14 24
7041-B-Flange Adaptor
350 600mm
14 24
SJ-300N-Butterfly Valve
350 600mm
14 24
41
OPERATING FEATURES
SYSTEM SIMPLICITY
Just as joints are easy to connect so they are
easy to disconnect.
FLEXIBILITY
The system permits limited angular deflection
in any direction without leakage so that uneven ground
may be followed using straight pipes. Transmission of
vibration from machines to pipelines can be minimised by
using at least two adjacent joints.
42
Dismantle
two
LOCKED JOINT
1. Locked joints mechanically lock the shouldered pipe
ends together securely and safely. The joints cannot blow
off under pressure nor can they pull out under vibration or
sag, because the shoulder sections of the couplings
engage the circumference of the pipe shoulders.
IMPORTANT:
1
1. PIPE END MUST BE SMOOTH.
The shoulder must be smooth and
any lumps of galvanising behind
the shoulder or on the pipe ends
removed.
2
2. The coupling , when applied , automatically
2. LUBRICATION
3
3. Line pressure automatically strengthens the seal by
acting internally on the ring lips. The higher the pressure
the tighter the seal.
SHOULDERED GASKETS
Standard Gaskets
Grade
R
Temp. Range
-50 to +65
Compound
Natural
rubber
-30 to +80
Nitrile
Recommended for petroleum, oil or gas products, air with oil vapours, vegetable and
mineral oils within the specified temperature range, except hot dry air over 60C and
water over 66C. Not recommended for hot water services.
50
80
100
125
150
150
200
250
300
350
Pipe
O.D.
Test
Pressure
Working
Pressure
mm
KPa
PSI
KPa
PSI
60.3
88.9
114.3
139.7
165.1
168.3
219.1
273.0
323.9
355.6
22000
18000
12500
9000
9000
9000
8000
8000
8000
8000
3190
2610
1810
1305
1305
1305
1160
1160
1160
1160
4150
4150
4150
3000
3000
3000
2660
2660
2660
2660
600
600
600
435
435
435
385
385
385
385
Mass
each
complete
Kg
1.2
1.5
2.0
3.0
3.5
3.8
5.9
9.1
11.8
15.4
43
OUTLET COUPLINGS
OUTLET COUPLINGS
Maximum recommended
Nominal
Pipe
Size
mm
400
450
500
600
Pipe
O.D.
Test
Pressure
Working
Pressure
mm
KPa
PSI
KPa
406.4
457.0
508.0
610.0
8000
8000
6000
6000
1160
1160
870
870
2660
2660
2000
2000
PSI
385
385
290
290
Mass
each
complete
Kg
25.4
29.1
33.8
27.8
Maximum recommended
Nominal
Pipe
Size
mm
50
80
100
150
Pipe
O.D.
Test
Pressure
Working
Pressure
mm
KPa
PSI
KPa
60.3
88.9
114.3
165.1
22000
18000
12500
9000
3190
2610
1810
1305
4150
4150
4150
3000
PSI
600
600
600
435
TOGGLE COUPLINGS
TOGGLE COUPLINGS
Maximum recommended
Nominal
Pipe
Size
mm
100
150
150
200
44
Pipe
O.D.
Test
Pressure
Working
Pressure
mm
KPa
PSI
KPa
PSI
114.3
165.1
168.3
219.1
22000
18000
18000
18000
3190
2755
2755
2755
6900
6900
6900
6900
1000
1000
1000
1000
Mass
each
complete
Kg
4.7
6.2
6.8
14.2
Maximum recommended
Nominal
Pipe
Size
mm
50
80
100
150
200
Pipe
O.D.
Test
Pressure
Working
Pressure
mm
KPa
PSI
KPa
60.3
88.9
114.3
165.1
219.1
11000
10000
8000
7500
6500
1595
1450
1160
1088
945
3660
3330
2660
2500
2156
PSI
530
480
385
360
315
Mass
each
complete
Kg
1.4
1.7
2.2
3.2
Mass
each
complete
Kg
1.3
2.0
3.0
3.3
8.3
Stand Off
5mm for pipe 88.9mm outside diameter and below.
6.5mm for pipe 114.3mm outside diameter up to and
including 762mm outside diameter.
D Dia
Ds Dia
Stand Off
Refer section
VICTAULIC Steel
Shoulder Rings
SHOULDER DIMENSIONS
NOMINAL
PIPE SIZE
OUTSIDE
DIAMETER
mm
50
80
100
125
150
150
200
250
300
350
400
450
500
550
600
650
700
750
TOLERANCE
mm
D
DIAMETER
mm
DS
DIAMETER
mm
PLUS
mm
MINUS
mm
L
DIMENSION
mm
60.3
88.9
114.3
139.7
165.1
168.3
219.1
273
323.9
355.6
406.4
457
508
559
610
660
711
762
60.3
88.9
114.3
139.7
165.1
168.3
219.1
273
323.9
355.6
406.4
457
508
559
610
660
711
762
66.5
97
122
149
174.5
178
232
286
336.5
368.5
419
470
520.5
571.5
622.5
673.1
723.9
774.7
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.4
1.9
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
2.4
16
16
17.5
17.5
17.5
17.5
20.5
20.5
20.5
24
25.5
25.5
25.5
25.5
25.5
25.5
25.5
25.5
ADJUSTABLE BENDS
BENDS
45
90 R
Nominal
Pipe Size
mm
To Suit Pipe
Outside Diameter
mm
A Minimum Length
End to End
mm
Nominal
Pipe Size
mm
To Suit Pipe
Outside
Diameter
mm
L
Centre to
Face
mm
R
Bend
Radius
mm
S Minimum
Length of
Straight
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
197
229
264
333
333
394
445
495
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
222
305
425
610
610
914
1575
1880
146
238
308
457
457
711
1270
1524
76
67
117
152
152
203
305
356
45
ADAPTORS
Shouldered to screwed B.S.P. male thread adaptor.
Shouldered to flanged adaptor.
CROSSES
C
C
M
Nominal
To Suit Pipe
Pipe Size
Outside Diameter
mm
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
Nominal
Pipe
Size
mm
To Suit Pipe
Outside
Diameter
mm
50
60.3
80
88.9
100
114.3
150 Flanged 165.1 / 168.3
150 Screwed
165.1
200
219.1
250
273.0
300
323.9
M Minimum
Overall Length
Nominal
To Suit Pipe
Short Pattern
Pipe Size
mm
mm
mm
mm
mm
318
423
470
507
507
605
757
909
100
100
100
100
150
100
100
100
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
152
203
229
254
254
305
381
457
Standard
ELBOWS 90 AND 45
REDUCERS
OFFSET TEES
45
C1
C2
D
C1
90
C2
45
E
Outside
Diameter
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
188.3
219.1
273.0
323.9
Pipe Size
C Centre
C Centre to Face
to Face
Standard Short Pattern 45 Elbows
mm
mm
mm
152
203
229
254
254
305
381
457
69
91
110
148
148
183
46
78
109
135
173
173
235
Nominal Pipe
Size of
Large End
mm
To Suit Pipe
Outside
Diameter
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
L Minimum Length
End to End
Short Pattern
Standard
mm
mm
203
229
305
305
330
381
457
90
112
150
150
162
Nominal
Pipe
Size
mm
To Suit Pipe
Outside
Diameter
mm
D
Centre
to Face
mm
E
Centre
to Face
mm
50
60.3
215
89
80
88.9
279
127
100
114.3
343
115
150
165.1
394
114
150
168.3
394
114
200
219.1
470
140
Y-PIECES
PIECES
SPRINGS
60
L2
L1
L2
L1
135
Nominal
Pipe
Size
mm
To Suit Pipe
Outside
Diameter
mm
D
Centre
to Face
mm
E
Centre
to Face
mm
Nominal
Pipe
Size
mm
To Suit Pipe
Outside
Diameter
mm
60.3
165
89
50
60.3
300
600
900
80
88.9
229
127
80
88.9
300
600
900
100
114.3
279
127
150
165.1
330
152
100
114.3
300
600
900
150
165.1
300
600
900
150
168.3
300
600
900
150
168.3
330
152
200
219.1
381
178
M
Minimum Overall Length
Lengths Available
mm
50
mm
Outside
Diameter
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
Pipe Size
SETTING PIECES
1121/2
L2 Centre
to Face
to Face
1121/2 Spring 135 Spring
mm
mm
197
273
378
546
546
819
1422
1702
187
260
365
521
521
778
1346
1600
R
Radius
mm
146
238
308
457
457
711
1270
1524
TEES
10
C
R
Standard
Short Pattern
mm
To Suit Pipe
Outside
Diameter
mm
mm
mm
368
413
470
521
521
692
876
978
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
152
203
229
254
254
305
381
457
69
91
110
148
148
183
To Suit Pipe
Pipe Size
Outside Diameter
Radius
mm
mm
50
80
100
150
150
200
250
300
60.3
88.9
114.3
165.1
168.3
219.1
273.0
323.9
C
Centre to Face
Nominal
Pipe
Size
mm
Nominal
47
Available From:
08 8304 7510
07 3860 3300
08 8935 0350
07 4972 8033
07 4955 1555
03 8795 2300
02 4955 0622
08 9494 0900
02 9756 1899
07 4775 5100
02 4271 1788
www.OneSteel.com
www.OneSteelBuildingServices.com
This information is provided for your assistance. However we are obliged to draw your attention to the
following: OneSteel provides the information contained in this brochure as a guide only for your information.
OneSteel has taken reasonable care to ensure the accuracy of the material but you should not rely on the
whole or any part of the information. Technology is changing rapidly and product specifications and or
manufacturing techniques may have changed since the first publication date of this document. OneSteel
expressly disclaims all liability whatsoever for (including any direct or indirect loss or damage, costs or
expenses howsoever incurred by any person) or reliance on the whole or any part of the information
contained in or omitted from this brochure. OneSteel recommends that you verify any information regarding
products with your independent expert adviser and rely solely on that advisers recommendations.
All trademarks are property of their respective owners
Victaulic" and Victaulite trademarks are owned by VICTAULIC COMPANY, Pennsylvania, United States of America
"OneSteel Building Service" is a Trademark of OneSteel Limited ( ABN 63 004 410 833 )
Doc Ref 064 March 04