Professional Documents
Culture Documents
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. ignore this completely i cut if off at the end because what i originally wanted to do didnt work 2. also ignore this little opening 3. ball of extra duct tape from all my duct tape projects
Image Notes 1. i did this quick so it wasn't neat but i went over it later with another piece to make it look smooth 2. pocket 1 3. pocket 2 4. pocket 3 5. pocket 4 6. pocket 5 7. pocket 6 8. secret pocket under here 9. ID pocket 10. main pocket
Image Notes 1. all these messy parts can have duct tape added to make it look neater, i was going quickly 2. License or other id can go here
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. 4 inches 2. 3 1/2 inches 3. 2 of these in total 4. 3 6/8 inches 5. 1 7/8 inches 6. 6 of these
Image Notes 1. 6 3/8 inches 2. 3 1/2 inches 3. 3 6/8 inches from the right and fold
Image Notes 1. you only need to duct tape the smaller side
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. trace more than you think you will need
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. trim to fit smaller side of the piece you just made
Image Notes 1. This is where the pocket will be taped so it has to be trimmed to fit n this piece. Male sure you tape the pocket on this side,
Image Notes 1. after you are done trimming cut out a small semi circle so you can remove your ID easily
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
2. This is the 4 inch by 3 1/2 inch piece laying on the larger section that didn't have tape on it before 3. Tape together here 4. tape together here 5. tape together here 6. try not to put too much tape where you bent the foil because the more tape will make it harder to bend
Image Notes 1. smaller piece 2. larger piece underneath 3. tape here 4. tape here 5. tape here
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. 4 inch by 3 1/2 inch piece 2. ID Piece 3. tape here 4. tape here 5. tape here 6. tape here but tuck the tape into the pocket so you don't tape the pocket closed 7. tape here but tuck the tape into the pocket so you don't tape the pocket closed 8. tape here also 9. tape 10. don't tape here or else no secret pocket
Image Notes 1. start adding pockets. start from the top then go down about 5/8 of an inch and repeat for a total of three pockets on each side Image Notes 1. pocket piece 2. center it on another piece of tape
Image Notes 1. 3 pockets 2. 3 pockets Image Notes 1. the flap is unfolded here ID card is facing other way 2. pockets go here for a total of three on each side
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. i did this quick so it wasn't neat but i went over it later with another piece to make it look smooth 2. pocket 1 3. pocket 2 4. pocket 3 5. pocket 4 6. pocket 5 7. pocket 6 8. secret pocket under here 9. ID pocket 10. main pocket
Image Notes 1. i did this quick so it wasn't neat but i went over it later with another piece to make it look smooth 2. pocket 1 3. pocket 2 4. pocket 3 5. pocket 4 6. pocket 5 7. pocket 6 8. secret pocket under here 9. ID pocket 10. main pocket
Image Notes 1. all these messy parts can have duct tape added to make it look neater, i was going quickly 2. License or other id can go here
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
Image Notes 1. I still need to make it neat and add something to decorate it. i just wanted to get this done so i could upload it.
Image Notes 1. ignore this completely i cut if off at the end because what i originally wanted to do didnt work 2. also ignore this little opening 3. ball of extra duct tape from all my duct tape projects
Related Instructables
Code Geass Themed Duct Tape Wallet & RFID Chip Blocker (Photos) by Shadow_Force
Comments
50 comments Add Comment view all 73 comments
awesomeness12345 says:
I made it and it was awesome
ColleenG says:
Feb 11, 2011. 1:05 PM REPLY I've used two peices of clear packaging tape place against each other to for a clear "cover, just do that twice and you've got this!
Goodhart says:
The table on the left appears to have some notebooks on it.
bubblebut says:
i tried to do it but I failed
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
cable511 says:
you dont need paper or foil just paste 2 sides of dt together holds up fine
maethor says:
why infoil?
Jun 19, 2010. 1:01 PM REPLY Would you be able to send me instructions on making it two colored? if so email: dkoberst@yahoo.com or if anyone is able to do that. Please respond or tell me how
epicismymiddlename says:
just use different duct tape for the different parts, i.e. use a different color for the credit card slots
troyqaz says:
This is taking a long time.
jagnat4000 says:
ikr
Ripstikr27 says:
Jeez... An hour and a half of my life has gone by putting tape on tin foil
janhunter says:
i dont understand!
jamesdude says:
i dont either
jagnat4000 says:
should I cover the back as well?
jagnat4000 says:
so that the outer one folds over the inner one neatly without overlapping at the edges.
iSpazz2 says:
i did mine in lime green duct tape. you can find it at hobby lobby and it looks awesome so far
mattspd says:
i dont get this with the folding and all.
jumpertoad says:
you did great for your first instructable!!!!!!!!!!!! this is the best one ive seen yet!
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
grannyjj says:
what picture?? Directions too vague..
grannyjj says:
directions not very clear!! Which way does the 4 x 31/2 lay?
sharlston says:
woaa thats well good,neat design -sharlston
swimmer95 says:
what is the "secret pocket" for and how do you get to it?
AznPanda says:
Mar 6, 2009. 11:12 PM REPLY I think mine turned out really well :O ur instructions weren't very precise so half way through i just made mine some other way but the basic design :o This one has 6 card pockets 1 ID pocket 1 Coin pocket and 2 Money pockets >.> i dont know about the others but yeah
Gh{O}sT says:
nice :D
buttonhead says:
Hey thanks a bunch for posting this i just made one and it looks awesome! :)
bazrakin says:
chrome leather!
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/
May 27, 2009. 5:07 PM REPLY Can you make it without paper or tin foil? Because everytime I've made somethin out of duck tape, I diddnt use anything else and they held up fine. :)
mchs60chip says:
Great Instructable i just finished my first in under 45 minutes
jacmaster88 says:
Do you need to add duct tape to the front AND back of the smaller side?
troyqaz says:
i think so.
troyqaz says:
I have no idea!
rawrulz17 says:
yes you do
troyqaz says:
I had the same problem.
troyqaz says:
I used construction paper. Much stronger
rensjuuuh says:
Mar 24, 2009. 9:08 AM REPLY Thanks! I got rid of the ID pocket, was hard to make and I didn't have ziploc bag either, but it turned out quite good :) And it took me about one hour..
Orpington2019 says:
Jan 22, 2009. 7:02 PM REPLY I was wondering if someone could either post a "How to tape" guide or direct me to one. I have made two of these wallets using this guide but dropping the ID holder and the first one took me 3 hours and the second was almost 4 hours. I must be doing something wrong. I would think it should only take about an hour. Any help would be great. Thanks!
AznPanda says:
I love mine mine is sooo awesome . it took me... 3 or 4 hours i lost count lool One way or another mines awesome .
austinburke. says:
Feb 4, 2009. 5:16 PM REPLY yeah, I've been working on mine for about an hour and I'm not even half way done! (: it is a bit challenging the first time I guess.
austinburke. says:
Finished it.. yeah I won't even post pictures it looks quite embarrassing.
Apollo2947 says:
it took me less than 30 min but it is kinda sloppy
Ridley006 says:
what kind of Tin Foil or Paper did you use?? is it the same thing as aluminum foil?? I think aluminum foil would be to week...
http://www.instructables.com/id/Awesome-Duct-Tape-Wallet-1/