Professional Documents
Culture Documents
HDB BLDG Sor 09 11
HDB BLDG Sor 09 11
SCHEDULE OF RATES FOR TERM CONTRACT FOR BUILDING MAINTENANCE WORKS TO VARIOUS HDB INDUSTRIAL ESTATES
PAGE 1 of 19 4 of 19
SCHEDULE OF RATES Excavation Concrete Work Brickwork & Blockwork Floor Finishes Carpentry & Joinery Ironmongery Structural Steelwork & Metalwork Signages Roofing Wall & Ceiling Finishes Painting & Decoration Glazing Fire Equipment Reinstatement of Water/Electricity Work Concrete Repair Water Seepage/Leakage Water/Building Component Test Miscellaneous Sanitary Daywork Supplementary Schedule of Rates 1 2 6 7 10 14 21 33 36 41 44 47 48 49 49 51 52 53 55 101 104
Page 1 of 19 SCHEDULE OF RATES FOR TERM CONTRACT FOR BUILDING MAINTENANCE WORKS TO VARIOUS HDB INDUSTRIAL ESTATES
GENERAL PREAMBLES
INTRODUCTION
The clauses in the General Preambles shall apply to all work items contained in the Standard Schedule of Rates. The Particular Preambles to each Trade shall be read in conjunction with the respective Trade in the Standard Schedule of Rates. All rates include the allowances for complying with the General and Particular Preambles. All rates contained in the Standard Schedule of Rates are fixed basic rates (in Singapore Currency) and no amendment whatsoever shall be made to such rates. The tenderers shall be deemed to have closely studied all rates contained herein and duly noted their implications. All rates contained in this Standard Schedule of Rates are exclusive of any Goods and Services Tax. Any such Goods and Services Tax shall be borne by the HDB as and when the same becomes due and payable. All work, materials and goods described in this Standard Schedule of Rates shall be of the respective kinds described in the Contract and in accordance with the instructions of the Superintending Officer or the Superintending Officer's Representative. Headings to groups of items shall be read as part of the descriptions of the items to which the headings apply. Where brand/trade names are given in the descriptions, they are solely intended for fixing the rates of the items. The products and materials to be used in the contract shall be governed by the specifications, Drawings and other documents forming the contract (and not this Schedule of Rates).
Page 2 of 19 INTRODUCTION (CONTD) 9 Description of Works and Inclusions Unless specifically stated otherwise, the following shall be deemed to be included in the description of the item of work:a) Labour and all costs in connection therewith including the labour in fabricating, assembling, setting, fitting and fixing of materials and goods in position. Materials and goods including materials required for lapping, jointing and the like and all costs in connection therewith such as delivery, unloading, storing, returning of packings, handling, hoisting and lowering. Preparing surfaces to receive work. Protecting materials and work. Waste of materials. All cutting and waste. Use of construction equipment, tools, vehicles and all costs in connection therewith. Cleaning up on completion and making good all work disturbed. General requirements set out in the Specifications, Drawings and other documents forming the Contract. Establishment charges, overhead and profit. Safety provisions required by HDB Safety Units and statutory requirements. Urgent mobilization of labour, plants and equipments in the shortest possible time when instructed by So Representative. Dismantle and removal of existing fittings/works affected by the new installation including make good disturbed areas, cart away and disposal unless otherwise specified. ENVI dumping fees.
b)
c) d) e) f) g)
h) i)
j) k)
l)
m)
n) 10
Unless otherwise stated, all work shall be measured net and for work measured by area, it shall be measured net and flat on the surface as fixed in its place. Unless otherwise stated, pipes are described by their internal diameters.
11
Page 3 of 19 INTRODUCTION (CONTD) Description of Works and Inclusions (Contd) 12 Where minimum deductions of voids are dealt with in this document they shall refer only to openings or voids which are within the boundaries of measured area. Openings or voids which are at the boundaries of measured area shall always be the subject of deductions irrespective of size. Stagings and scaffoldings erected as instructed and approved by SO Representative shall be measured and paid separately unless otherwise specified. Unless otherwise stated, the term as specified means as specified in any of the documents forming part of the Contract. The following abbreviations are used for the units:m m2 m3 no kg ton pr sht ltr hr 16 Linear metre Square metre Cubic metre Number Kilogram Tonne Pair Sheet Litre Hour
13
14
15
The GENERAL PREAMBLES and the PARTICULAR PREAMBLES TO VARIOUS TRADES shall also be applicable to the Supplementary Schedule of Rate.
Page 4 of 19 PARTICULAR PREAMBLES TO VARIOUS TRADES 1.0 EXCAVATION Definition of Ground Ordinary ground:- includes spoil or rubbish of every description, rubbish tip material etc, sand gravel, decomposed granite, red or white earth, loamy or gravelly clay, gravelly laterite, mud, bog or any other formation of pick and shovel and at any depth. Description The description of each item of excavation shall be deemed to include excavating around foundation, piles and confined areas, getting out, removing of bakau piles, trimming, levelling and compacting bottoms of excavations, keeping sides plumb and planking and strutting. Measurement The measurement of all excavations and subsequent disposal shall be those before excavating. The increases in bulk and any extra excavation required for earthwork support, planking and strutting and formwork for concrete shall be deemed to be included in the rates. No allowance for working space shall be made in the measurement of all excavation unless the method of construction requires workmen to operate from the outside of the structure. In such cases, a working space of 600mm shall be measured from the external face of the structure. Filling shall be measured as equal to the void to be filled. Any thickness stated shall be deemed to be after compacting. Rate Rates for each item shall be held to include for keeping all excavation free from water and site dry pumping or bailing if required and providing any temporary drains required. Rates shall be held to include for engaging licensed cables/services detection worker to carry out all cable/services detection works prior to the commencement of excavation works and any piling/penetration works. Breaking-Up/Hacking Rates shall include cutting to concrete/premix surfaces by hand held cutting tools to a required depth as instructed by S.O. Representatives prior to hacking.
1.1
1.2
1.3.1
1.3.2
1.3.3
1.4.1
1.4.2
1.5
Page 5 of 19 2.0 CONCRETE WORK Rate Rates for each item of concrete shall be held to include the following:a) Forming, cutting grooves, chases, mortices, holes and making good any other sundry items of a like nature. Extra labour for laying to falls, or cambers and preparing surfaces to receive screeds or pavings also to be included. All tests on concrete, cement and aggregate etc, as required and compliance with the strengths as specified. Tamping and/or vibrating to give thorough compaction; working between and around reinforcements. Laying on any type of sub-base; preparing and leaving surfaces to receive screeds or paving. Trowel smooth to surface with steel trowel or brush finished.
2.1
b)
c)
d)
e)
f)
2.2
Deduction No deduction shall be made in the measurement of concrete work for:a) b) c) Voids of 0.05 cubic metre or less. Volume of the reinforcement and steelwork. Openings in walls, floor, roof slabs and the like of 0.10 square metre or less.
2.3
Reinforcement Description The description of each item of reinforcement shall be deemed to include:a) b) Allowances in the weight of reinforcement for rolling margins. All cleaning, cutting, bending, fabricating, placing, tying and the provision of all necessary distance blocks, tying wires, spacers or chairs, temporary fixings and supports. Brushing and cleaning all reinforcement free of rust, dust, mill scale, dirt, oil and any other deleterious matter.
2.3.1
c)
Page 6 of 19 2.0 2.3 CONCRETE WORK (CONTD) Reinforcement (Contd) Measurement The conversion factor for the various steel reinforcement bars shall be as follows: 6mm diameter 7mm diameter 8mm diameter 9mm diameter 10mm diameter 13mm diameter 16mm diameter 20mm diameter 22mm diameter 25mm diameter 28mm diameter 32mm diameter 2.4 2.4.1 Fabric Reinforcement Rate Rates for each item of fabric reinforcement shall be held to include for extra material at laps, tying wires and all bending, cutting and notching around obstruction. Only the net area covered shall be measured and no deduction shall be made for opening less than 1.00 square metre. Formwork Description The description of each item of formwork shall be deemed to include:a) All necessary boardings, supports, erecting, framing, cutting, perforations for pipes, angles, cleaning, wetting and treatment with mould oil, mould liquid or limewhite and the like. All splayed edges, notchings, allowance for overlaps and passings at angles, battens, strutting, bolting, wedging, easing, striking and removal. 0.222 kg/m 0.302 kg/m 0.394 kg/m 0.499 kg/m 0.616 kg/m 1.042 kg/m 1.579 kg/m 2.466 kg/m 2.984 kg/m 3.854 kg/m 4.834 kg/m 6.313 kg/m
2.3.2
2.5 2.5.1
b)
2.5.2
Measurement Formwork shall be measured to the surface of work sloping more than 15 degree from the horizontal.
Page 7 of 19 2.0 2.5 CONCRETE WORK (CONTD) Formwork (Contd) Deduction No deduction shall be made in measurement of formwork for:a) b) c) 2.6 Openings less than 1 square metre. Intersection of main and secondary beams. Intersection of beams and stanchion casing or columns.
2.5.3
Unless otherwise stated, rates for concrete, reinforcement and formwork shall be applicable to all work irrespective of locality, positions, shapes and height. Precast Work Description The description of each item of precast work shall be deemed to include concrete, reinforcement, formwork including the formation and filling of pockets, holes, chases and recesses for anchors, bolts and the like, grouting, pointing of joints, surface finishes, delivery, unloading, hoisting, erecting, fixing including all necessary temporary erection gear, bracing and working platforms. Precast Concrete Vent Measurement The measurement of precast concrete vents shall be taken by volumes without deduction of voids. Surface Water Channels Rate Rates for each item of surface water channels shall be held to include for all angles, intersections, ends, outlets and extra labour and material for forming grooves or rebates to sides. Breaking-Up/Hacking Rates shall include cutting to concrete surfaces by hand held cutting tools to a required depth as instructed by S.O. Representatives prior to hacking.
2.7
2.7.1
2.8
2.8.1
2.9
2.9.1
2.10
Page 8 of 19 3.0 BRICK AND DRAINAGE WORK Rate The rates for each item of block, brickwork shall be held to include for all special made blocks, bricks and in-situ concrete in lieu, all rough and fair cuttings, oversailing and receding courses, rough relieving and discharging arches, wedging and pining, raking out joints for and pointing flashings, bedding plates, bedding and pointing of frames, parging and coring flues, labour eaves filling, plumbing angles, forming square and rebated reveals, cut squints or birdsmouths, notches, forming, leaving or cutting chases, holes and mortices, cutting and pining and making good and any other sundry items of a like nature. Rates for blockwork and brickwork shall be applicable to all work irrespective of positions, patterns, shapes and height. Deduction Deductions shall be measured the net sizes of the openings and recesses, including the extra width or rebated reveals. No deductions shall be made for openings of 0.50 square metre or less. Deductions shall be made for strings, sills, lintols and the like only when exceeding 100mm in height.
3.1
3.2
3.3
3.4
4.0
FLOOR FINISHES Description The description of each item of floor finishes shall be deemed to include all temporary rules, temporary grounds, temporary screeds and the like, cutting holes, notching and the like, all normal bedding and pointing materials, providing all necessary samples, cleaning down and making good around pipes, sanitary fixtures and the like, work in narrow widths and small quantities in areas interrupted by seatings, channels and the like, all internal angles, quirks, grooves, throats, drips, coves and rounded external angles not exceeding 25mm radius, angles, stops, intersections, fair ends junctions, wreathed corners and the like on cornices, mouldings, enrichments, coves, skirtings, gutters, channels, strings, kerbs and similar or other sundry items of a like nature. The description of each item of floor finishes shall be deemed to include protecting surfaces from the weather or building operations. Screed/rendering shall include for towelling smooth with steel trowel or brush finished. Rate Rates for each item of skirtings, risers, moulded edges, channels, curbs and the like shall be held to include for all short lengths, formed, cut and purpose made angles, junctions, end, necessary UPVC trimming pieces, etc and making good and any other sundry item of a like nature.
4.1
4.2
4.3
Page 9 of 19 4.0 FLOOR FINISHES (CONTD) Deduction No deduction shall be made for openings of 0.50 square metre or less. Breaking-Up/Hacking Rates shall include cutting to concrete surfaces by hand held cutting tools to a required depth as instructed by S.O. Representatives prior to hacking. ROOFING Description The description of each item of roofing shall be deemed to include:a) All laps, straight, skew and circular cutting at eaves, verges, top edges, abutments, valleys and hips, cutting holes for pipes, nails, screws, clips, pellets, straps and the like. Chasing the structure for burning-in or tucking in edges of coverings, flashing and the like. Holes in coverings, underbeds and insulations for pipes, standards and the like and making good.
4.4
4.5
5.0
5.1
b)
c)
5.2 5.3
Deduction No deduction shall be made for voids of 0.50 square metre or less. Membranes System and Panel Roofing System Rate Rates for Waterproofing Membranes System and Panel Roofing System shall be held to include for narrow widths, small quantities, temporary rules, covering up, protecting after laying and cleaning on completion, all labour to form arrises, fair edges etc., all cuttings and working around pipes, dress down at eaves to form drips or carried up at abutments to walls, pipes, parapets, skirtings, concrete curbs etc. and the like. Profiled Sheet Roofing Description The description of each item of profiled sheet roofing or cladding shall be deemed to include all cutting at square and raking abutments, top edges, bedding and pointing eaves fillers, verges, cutting and fitting and making good around outlets, pipes and any other sundry items of a like nature.
5.3.1
5.4
5.4.1
Page 10 of 19 6.0 CARPENTRY AND JOINERY Description The description of each item of carpentry work shall be deemed to include all cutting, notching, boring, sinking, pelleting, fitting, trimming, mitring, halving, morticing, tenoning, dovetailing, scarfing, wedging and all ends, splayed edges, short lengths and temporary supports and any other sundry of a like nature and also all labour in forming, drilling for bolts and fixing in position complete with nails, screws or adhesives. The description of each item of joinery work shall be deemed to include all nailing, gluing, screwing, plugging, cutting, notching, holes, housing ends, mitring ends and shaped ends, angles, junctions, heading joints, short lengths, tongued angles, splayed or rounded edges, chamfers, rebates, grooves and any other sundry items of a like nature including stops and working cross-grain, fitting and hanging and the like. Nominal sizes are stated for wrot timber and an allowance of 2.5mm is permitted for each wrot face. Rates for windows and doors include hanging and fixing. Where ironmongery is included in the description of doors, it shall be deemed to include hinges, floor springs, door gears, locks, latches, catches, bolts, closers, holders, padlocks, stoppers, push-bars and plates, pull bars and handles, kickplates, locking eyes and the like as specified.
6.1
6.2
6.3
6.4 6.5
7.0
IRONMONGERY Rate Rates for each item shall be held to include for supply, delivery to site and fixing complete with all matching screws of the same finish as ironmongery, nails, pins or brads, cutting sinking and boring and morticing as required, oiling and easing and adjusting all moving parts, taking off and refixing after painting where necessary and handing 3 keys properly labelled to the Superintending Officer or the Superintending Officer's Representative etc unless otherwise described.
7.1
Page 11 of 19 8.0 8.1 STEEL AND IRON WORK Steel Work Description The description of each item of steel work shall be deemed to include:a) b) Allowances for rolling margins and the weight of welding materials. Shop and site fabrication including drilling, cutting (including holes and openings for other trades), notching, splicing, riveting, bolting, machining ends and bearings, delivery, unloading, landing, hoisting, erecting, fitting and fixing in position. Provision of all necessary construction equipment, temporary bracing supports and the like required for erection, providing samples and tests required by the specification, the inspection of welds including the use of any special radio-graphic techniques. Bolts and Nuts (including anchor bolts/studs) and any type of washer which may be required. Preparation of shop Drawings.
8.1.1
c)
d)
e)
8.1.2
Deduction No deduction shall be made for drillings, holes, notchings, splay cuts and the like. Measurement Weights stated shall be net theoretical weights. Steel sections and plates in connections or fitted stiffeners, column cap and base plates, rigid frame bases and butt plates, purlins, girts, eaves, fascias and similar cleats or brackets attached to trusses, lattice girders and open web joists and plates, including chequered plates in landings, treads and risers and similar items shall be weighted at net dimensions. Irregular, including circular shaped plates shall be weighted at the smallest size rectangles from which they can be cut; regular and triangular shaped plates shall be weighted at net dimensions. Half or other parts of steel sections in connections shall be weighted at half the weight of the section from which they have been cut when equal to or less than half the section and at the full weight of the section from which they have been cut when greater than half the section.
8.1.3 8.1.4
8.1.5
8.1.6
Page 12 of 19 8.0 8.2 STEEL AND IRON WORK (CONTD) Metal Work Description The description of each item of metalwork shall be deemed to include:a) b) Allowances for rolling margins and the weight of welding materials. Cutting, notching, mitring, welding, riveting, bolting, fabricating, drilling, delivery, unloading, handling, assembling, hoisting, fitting and fixing in position, bedding, filling in solid, polishing and pointing including necessary lugs or other attachments. Protection such as wrapping finished work with paper, coating with grease or carrying out such other protective measures as may be required and removing and cleaning on completion. Providing samples and testing as required. Preparation of shop Drawings.
8.2.1
c)
d) e)
8.2.2
Deduction Weights stated shall be net theoretical weights. No deduction shall be made for notches, holes and the like.
9.0
WALL AND CEILING FINISHES Rate Rates for each item shall be deemed to include the provision of keys to receive finishes, all temporary rules, temporary grounds, temporary screeds and the like, cramps, dowels, ties, special metal supporting brackets and the like, cutting holes, notching and the like, masking, labour to internal angles other than coved angles, making good around pipes, sanitary fixtures and the like, work in narrow widths and small quantities, joints between different types of work, joints between new and old work, internal angles, fair edges, rounded or chamfered edges or angles, quirks, grooves, V-joints, groin points and other intersections of curved surfaces, rounded coves and external angles not exceeding 25mm radius, necessary UPVC trimming pieces, mitres, stops and the like on cornices, mouldings, architraves, coves, skirtings, gutters, strings and all making good and any other sundry items of a like nature. Rates for each item shall also be deemed to include protecting surfaces from the weather or building operations. Rates for each item of wall tiling shall be held to include for narrow widths and small quantities, fittings around air bricks, pipes and the like and any other sundry items.
9.1
9.2
9.3
Page 13 of 19 9.0 9.4 WALL AND CEILING FINISHES (CONTD) Rates for each item of terrazzo shall be held to include for narrow widths and small quantities, and for all temporary rules, internal angles, arises, joints between different types of terrazzo, quirks and all making good and any other sundry items of a like nature on in-situ terrazzo, fitting around air bricks, pipes and the like and any other sundry items of a like nature on precast terrazzo. Deduction No deduction shall be made for openings of 0.50 square metre or less. Measurement In the measurement of plastering, no deduction shall be made for casings for pipes under 300mm wide or angles which are finished in a different material if these do not exceed 100mm girth. "Within the building" shall mean surfaces within the internal of buildings/flats, corridors, staircases and the like which normally do not entail scaffolding or mechanical cradles to carry out the works. "External face of building" shall mean surfaces such as gable end walls, front/back external walls and any other surfaces which are constantly exposed to weather and/or which normally require the use of scaffolding or mechanical cradles to carry out the work. Work shall be deemed to be executed when scaffolding has been provided during the course of construction. Should scaffolding be required separately just to execute the work, it would be paid as an extra item.
9.5
9.6
9.7
9.8
9.9
10.0
SANITARY, WATER AND GAS INSTALLATION Description The description of each item of pipework shall be deemed to include:a) All short lengths, joints in the running lengths, joints to all branches, tees, sockets, sleeves, connectors, backnuts, nipples, standard pipe framings or supporting clips, saddles, fastening brackets, holderbats, straps and the like. Giving notices. Complying with all requirements of the relevant authorities, paying fees and the like in connection with the installations and preparing and submitting Drawings for approval if required. Removal of existing if necessary unless otherwise specified.
10.1
b) c)
d)
Page 14 of 19 10.0 10.2 SANITARY, WATER AND GAS INSTALLATION (CONTD) Drain Pipes Pipes for soil drains shall be sound salt-glazed unglazed stoneware pipes free from breakage, distortion or fire cracks or approved UPVC pipes and of sizes shown. All drains under buildings shall be of Spun cast iron pipes complying with BS 4622:1970 Class 2 laid on concrete bed. Drain pipes shall be laid in straight lines to even falls. Only flexible jointed pipes approved by the Sewerage Department, shall be used for drain-line pipes. Soil, Waste and Vent Pipes The soil, waste and vent pipes are to be of cast iron (SS 33:1975 OR UPVC SS 213:1979) of the sizes to match existing or as directed. All jointing and fixing requirements shall be in strict accordance with the manufacturer's instruction. Fittings All sanitary fittings shall be of type currently approved by the Board and the relevant local authorities. Sample shall be submitted before hand if required. Squat Pan Squat pans shall be of vitreous China complying with British Standards 3402:1964, of approximate dimensions 660 x 254 x 330 mm deep white glazed washed down type with "P" or "S" traps, cleaning eye and stopper. Pans shall be of pattern and quality currently approved by the Ministry of the Environment. Each pan shall be completed with approved high level flush cistern with 40mm diameter P.V.C. or galvanised iron flush pipes. Flush pipes shall be held at mid height by holderbat securely fixed to wall. Galvanised pipes shall be provided with 150mm high 16mm thick protective cone at base of 1:3 cement mortar. Flushing Cisterns Flushing cisterns shall be of type currently approved by HDB, 9.0/4.5 litres dual action flushing cistern or approved in which pull chain will release either 4.5 or 9.0 litres of water when desired. The levers shall be of aluminium alloy. White Glazed Fireclay Sinks Glazed fireclay sinks where required shall be 610mm x 450mm x 200mm white fireclay "Belfast" or other approved pattern fixed on cantilever brackets complete with traps, outlet pipes, and rubber or vulcanite plugs.
10.3
10.4
10.5
10.6
10.7
Page 15 of 19 10.0 SANITARY, WATER AND GAS INSTALLATION (CONTD) Water Installation All pipes and pipefittings shall be approved by Water Department, PUB unless otherwise specified. (A) Ductile Iron Pipes for Water Supply All ductile iron pipes and fittings for water installation shall comply with BS 4772:1988 and ductile iron flanges shall comply with BS 4504. These pipes shall be cement mortar lined carried out in accordance with the relevant clauses in BS 543:1981. The lining shall be applied centrifugally by spinning the pipe in an approved plant and shall adhere firmly to the internal surface of the pipe. Lining shall also apply to fittings by means of approved process. The cement mortar shall consist of equal volume of Portland Cement, granite dust and sand correctly measured. The maximum grain size of sand or granite dust shall be clean, free from clay, animal, vegetable or other foreign matter. The internal surface of pipes shall be thoroughly cleaned and free from rust, scale or other deposit immediately before lining. The thickness of the lining shall be 6mm, tolerance +3mm, -0mm for 100mm nominal diameter pipe. The lining shall adhere firmly to the inside of the pipe and shall be finished smooth, even and free from any cracks or blemishes. The lining shall be continuous from spigot and to the beginning of the socket for pipes with spigot and socket joint and shall be continuous from face to face of flanges in the case of flanged pipes. (B) UPVC (Service/Distributing Pipes and Fittings) Water Pipe (i) All the service/distributing pipes and fittings shall be of unplasticised P.V.C. Corrosion resistant pipes complying with SS 141:1976 Class E and fittings complying with SS 174:1977 with its latest amendments and all tests as required by Water Department, PUB. Supply and fix all the UPVC pipes to the sizes and locations as shown in the drawings. The diameter shown shall be of norminal size. The mean tolerances on outside diameter shall conform to SS 141:1976. The pipe walls shall internal and external reasonably free from heat marks. The ends axis of the pipe. be homogenous throughout and the surfaces shall be clean, smooth and grooves, blisters, wrinkles, dents and shall be cleanly cut and square with the
10.8
Page 16 of 19 10.0 10.8 SANITARY, WATER AND GAS INSTALLATION (CONTD) Water Installation (Contd) (B) UPVC (Service/Distributing Pipes and Fittings) Water Pipe (CONT'D)
(ii)
The method of fixing UPVC pipes to UPVC pipes shall be as follows:(a) (b) All pipes must be sawn square. All swarf, burr and sharp edges shall be removed after cutting. The pipe end and the socket in pipes or fittings must be cleaned with cleaning fluid or methylated spirit and allowed to dry. No sand paper is allowed for cleaning the pipes and fittings. The spigot shall be marked with a pencil line at a distance to the depth of the socket in fittings or to the depth of sockets formed in pipe. All pipes ends and internal face of socket shall be thoroughly coated with solvent and allowed to dry. Apply the second coat of solvent as before and insert the pipe into socket immediately. Surplus solvent must be removed from the top of socket using a dry cloth. After jointing the joint shall be held firmly for a period of 30 seconds and not disturbed for at least 5 minutes. All joints must be jointed with suitable sockets recommended by the pipe manufacturer. In situations where a pipe and socket joint is not possible, a coupling shall be used. No socket belling shall be allowed when joining UPVC pipes.
(c)
(d)
(e)
(f)
(g)
(h)
Page 17 of 19 10.0 10.8 SANITARY, WATER AND GAS INSTALLATION (CONTD) Water Installation (Contd) (B) UPVC (Service/Distributing Pipes and Fittings) Water Pipe (CONT'D) UPVC adoptors shall be used for jointing of UPVC pipes to other materials and also to the pipe manufacturer's recommendation or as follows:(a) An approved epoxy compound shall be used. A caulking ring or bush shall be glued to the end of the UPVC pipe. For all jointing assemblies the solvent weld cement method shall be used.
(b)
All fixing work shall be carried out in strict accordance with the pipe manufacturer's instructions. (iii) Pipes shall be well supported by UPVC shackle clips. These supports shall sufficiently allow free movement of the pipe during temperature changes. Maximum Maximum Horizontal Support Vertical Support Nominal Size Spacing Spacing (mm) (mm) (mm) 10 15 20 25 32 40 50 65 & Above 400 400 500 600 700 800 900 1000 800 1000 1200 1400 1600 1800 1800 1800
Page 18 of 19 10.0 10.8 SANITARY, WATER AND GAS INSTALLATION (CONTD) Water Installation (Contd) (C) Stainless Steel Water Pipes All Stainless steel Water pipes, fittings and accessories shall be approved by Water Department, PUB and to the requirement of BS 4127:Part 2:1972 with its latest amendments. The internal and external surfaces of the pipes and fittings shall be clean, smooth and free from defects that would impair their performance in service. Cutting and fixing shall be in strict accordance with the manufacturer's instructions. All stainless steel pipes shall not be bent. Pipes shall be well supported by non-corrosive (galvanised steel) supporting clips. Unless otherwise specified, light gauge stainless steel pipes shall be used for water supply. The stainless steel pipefittings shall be of capillary or compression fittings of copper alloy and shall comply with BC 864:Part 2:1983 and all PUB latest requirements. Fittings of 15mm size and longer shall be legibly marked with the marker's name or trademark. Pipes shall be well supported by supporting clips or hangers. Maximum Horizontal Support Spacing (mm) 600 600 1200 1200 Maximum Vertical Support Spacing (mm) 1200 1200 1800 1800
11.0
GLAZING Rate Rates for each item of glazier shall be held to include for cutting and rounded edges, fixing panel pins, clips, brass screws and cup and neoprene strips where necessary and leaving the glass clean on completion.
11.1
Page 19 of 19 12.0 PAINTING AND DECORATING Rate Rates for each item of painting shall be held to include for all necessary preparation of surfaces including cleaning off, sandpapering woodwork, wire brushing metal and leaving all surfaces free from dust, rust, grease and oil before painting, narrow widths, etc. Deduction No deduction shall be made for openings of 0.50 m2 or less. Work shall be deemed to be executed when scaffolding has been provided during the course of construction. Should scaffolding be required separately just to execute the work, it would be paid as an extra item.
12.1
12.2 12.3
13.0
CABLE DETECTION SERVICES Rate All rates for Cable Detection Services shall deemed to include the following: (A) (B) (C) Purchase of Authorities existing utility plans; 3 Sets of detection reports on the pegging of detected services on site; and 3 Sets of detailed drawings on the detected underground services lines.
13.1
14.0
DAYWORK Rate Rates shall be applicable in respect of all work executed on a day work basis. During the continuance of such work, the Contractor shall keep proper records of the names, occupations and working hours of all workmen employed for such work and the quantities and descriptions of all materials and construction equipment employed. Such records, receipts or vouchers must be verified by the Superintending Officer or the Superintending Officer's Representative before payment can be effected. Rates for equipments and plants shall be deemed to include maintenance and fuel unless otherwise specified.
14.1
14.2
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION EXCAVATION Excavation oversite from ground level in ordinary ground to formation level including removing surplus excavate materials from site to contractor's own dumping ground. * Excavation to form trenches for pilecaps, foundations, beams, pier holes, drains etc including forming of bottom, part return, fill and ram and remainder get out and deposit at contractor's own dumping ground *(A002 A003) Not exceeding 1.50m deep Exceeding 1.50m deep Extra over for item A001 to A003 using hand excavation for which mechanical means is not possible or practical. Break-up concrete including cutting of reinforcement if any and removal of concrete from site to Contractor's dumping ground Break-up concrete (including removal of reinforcements if any)/bricks broken to 50-70mm in size as hardcore including levelling, compacting by approved mechanical means including 50mm thick sand blinding Hard-core in beds, comprising of clean broken bricks/concrete, deposit, spread, mechanically consolidated and including sand blinding/topping over. Good earth filling obtained from Contractor's source and fill in layers 300mm thk, including levelling and consolidation of earth by approved mechanical means. Plant mixed crushed granite aggregate spread (max size 50mm & below) deposited, levelled and rolled consolidation by mechanical roller. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A001
m3
10.20
m3 m3 m3
A005
m3
85.80
A006
m3
73.60
A007
m3
18.20
A008
m3
10.40
A009
m3
48.60
PAGE 1 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION EXCAVATION (CONT'D) Quarry waste, spread & level including consolidation by mechanical roller Lay clear/black plastic sheet to prepared sub-base/earth surfaces. CONCRETE WORK * Reinforced concrete to site work, substructure & superstructure, with 20mm to 10mm granite mechanically mixed, working around rod or fabric reinforcement. (Reinforcement formwork measured separately). *(A012 A014) Grade 20. Grade 25. Grade 30. Precast concrete grade 20 in heelstones, cills and lintels including mould and reinforcement. Mild steel/high tensile steel rod reinforcement irrespective of size fabricated and laid in position. Drill holes into concrete 50mm depth and apply 'HILTI-HIT-HY-150' adhesive mortar to bond 10mm diameter reinforcement bar. * Welded steel fabric reinforcement well lapped and tied at joints (measured nett). *(A018 A027) A6. A7. A8. A9 B6. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A010
m3
46.90
A011
m2
0.30
m3 m3 m3 m3
A016
kg
1.30
A017
no
2.70
m2 m2 m2 m2 m2
PAGE 2 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CONCRETE WORK (CONT'D) B7. B8. D4(G) D4 No. 2210 * Timber formwork including all necessary boarding, supports, erecting, framing, cutting, perforation for pipes, angles, cleaning, wetting treatment with mould oil, notching, laps, battens, strutting, bolting, wedging, easing, striking & removal *(A028 A029) Below ground level (Footpath, ground slab, drains, foundation etc) Above ground level 10 x 15mm(depth) expansion joint filled with bitumen. 12 x 25 mm(depth) expansion joint filled with bitumen. 25 x 200mm(depth) expansion joint filled with bitumen and filler board 10mm wide x 40mm depth 'Quicseal 201' or other approved equivalent PU sealant PVC 'L' shaped Floor Strip on cement mortar secured with masonry nails if necessary 10mm thick polystyrene foam to expansion joint 15mm thick polystyrene foam to expansion joint "NH 200" neoprene compression seals system to expansion joints | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m2 m2 m2 m2 m2
A028
m2
15.60
A029 A030
m2 m
24.20 1.00
A031
2.10
A032
3.80
A033
7.20
A034
2.60
A035
m2
1.90
A036
m2
2.20
A037
82.20
PAGE 3 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CONCRETE WORK (CONT'D) Rake out joints to an average depth of 25mm to expansion joint. Brush out all loose joint compound and mortar and fill the groove solid with approved polyurethane sealant to form a continuous joint.(backer rod measured separately) Rake out bitumen from suspended floor slab's 25mm wide expansion joint and refill with approved polyurethane sealant including backer rod. 225-250mm wide (internal) reinforced concrete (Grade 25) surface drain constructed with 75mm thick sides and 100mm thick bottom. All sides and bottom shall be reinforced with a layer of BRC No. B6 wiremesh. All exposed sides, bottoms and arises rendered smooth in cement mortar (1:3) including all necessary excavation, hard-core, sand blinding, formwork and PC channel laid to fall to an average invert depth of 300mm. (Breaking up of existing drain measured separately) Add to (or deduct from) item A040 for each 50mm depth over (or under) 300mm depth. 300mm wide (internal) reinforced concrete (Grade 25) surface drain constructed with 100mm thick sides and bottom. All sides and bottom shall be reinforced with a layer of BRC No B6 wire mesh. All exposed sides, bottom and arises rendered smooth in cement mortar (1:3) including all necessary excavation, hard-core, sand blinding, formwork, and PC channel laid to fall to an average invert depth 400mm. (Breaking up of existing drain measured separately) Add to (or deduct from) item A042 for each 50mm depth over (or under) 400mm depth. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A038
3.70
A039
6.20
A040
62.70
A041
6.90
A042
95.90
A043
7.20
PAGE 4 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CONCRETE WORK (CONT'D) 50mm thick precast concrete slab over 225 to 300mm wide surface drain. 1:3 cement and sand mortar (min 13mm thick) regrading to invert channel of 225 to 300mm wide surface drains including hacking off existing channel/plastering. Sawn cut sides and hack off existing screed of scupper/water channel and regrade to fall with minimum 20mm thick 1:3 cement and sand mortar including make good affected areas. * Reinforced precast concrete paving slabs laid on sand bed and jointed in cement and sand mortar. (excavation & removal of existing slabs to be measured separately) *(A047 A048) 50mm thick 75mm thick 300x300x50mm thick polyproplene fibre reinforced vibro-compacted porous concrete slab with cement and 9 or 14mm thick aggregate (1:4) mix for concealed drain. Labour for take out existing loose or sunken precast concrete paving slabs and stack aside for re-use including cart away damaged slabs Select from stack and re-use existing 50/75 thick concrete slab (including sand binding and jointing in 1:3 cement mortar) 600x400x100 mm thick precast concrete BG slab including sand bed to receive slab and turfing. (excavation measured separately) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A044
14.10
A045
5.50
A046
4.60
m2 m2 m
A050
m2
3.90
A051
m2
6.90
A052
m2
64.50
PAGE 5 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION BRICKWORK AND BLOCKWORK * Common brickwall laid in 1:3 cement mortar with 10mm joints raked 10mm deep flushed pointed as works proceeds *(A053 A054) Half brick thick reinforced with galvanised expanded metal reinforced at every 3rd course One brick thick Extra over ordinary brickwork for forming exposed faces in red/overburnt facing bricks and pointed in approved cement mortar One brick thick wall coping/capping with bull nose facing bricks laid in cement and sand mortar (1:3) including pointing. Half brick-wall in standard common bricks built honeycomb laid in cement and sand mortar (1:3) with raked out joints or flush pointed as work proceeds. * Hollow block wall in cement and sand mortar (1:3) joints including expanded galvanised steel reinforcement at alternate course *(A058 A059) 100mm thick 150mm thick 190(L)x190(B)x95/80(THK)mm glass blocks laid in cement and sand mortar (1:3) and reinforced with expanded metal reinforcement including pointing of joints as specified Approved damp proof course complying with BS 6398 Type B (felt fibre base type) well lapped at joints and bedded in cement mortar (1:3) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A053
m2
28.00
A054 A055
m2 m2
55.50 26.70
A056
13.90
A057
m2
24.70
m2 m2 m2
A061
m2
8.00
PAGE 6 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION BRICKWORK AND BLOCKWORK Breaking up block/brickwall including finishes and cart away. Labour and material pointing joints of brickworks in coloured cement. Labour raking out joints of existing brickwork, clean, re-point with cement grout with a flush joint. Cutting out existing block or brickwork to form chase etc including making good and removing debris off site. Not exceeding 300mm girth. Cutting out existing block or brickwork to form chase etc exceeding 300mm and not exceeding 600mm girth including making good and removing debris off site. Hammer dressed random rubble in granite laid in cement mortar (1:3) as wall including pointing. FLOOR FINISHES Heavy duty unglazed ceramic floor tiles (minimum 8mm thick) complying to BS 301:1984 and bedding on 20mm cement and sand to floor, kerbs, arises etc Heavy duty unglazed ceramic nosing tiles in edging or steps laid and jointed on 20mm cement & sand screed 300 x 300 x 9mm thk homogenous tiles for floor complying to SS 301 and bedding on 20mm thick cement and sand screed to floor, kerbs, risers etc 10.5 mm thick approved homogeneous wall/floor tiles laid with prepack screed and bedded on 20mm thick 1:3 cement and sand mortar rendering (include kerbs and risers). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A062
m3
63.60
A063
m2
3.00
A064
m2
4.90
A065
43.60
A066
49.40
A067
m2
34.80
A068
m2
43.00
A069
9.40
A070
m2
44.20
A071
m2
43.30
PAGE 7 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION FLOOR FINISHES (CONT'D) Mosaic to floor/wall to match existing including 1:3 cement and sand screed Hack off concrete floor surfaces/ finishings to a depth not exceeding 50mm thick, form keys, clean and wash to receive new finishes including cart away debris to dumping ground Hack existing floor to form keys, clean and wash to receive new finishes. Apply one coat of approved bonding agent to concrete surface to receive new rendering/finishings. Apply 2 coats "Quicseal 104"/ "Neogard-Perma III Elastomeric" or approved equivalent flexible cementitious liquid waterproofing membrane. 20mm thick cement and sand (1:3) rendering to floor trowelled to a smooth finish including forming of expansion joints. Add to (or deduct from) item A077 for each additional 5mm thick over (or under) 20mm cement and sand (1:3) rendering * 20mm thick cement and sand (1:3) rendering to skirtings, treads, risers, curbs and returns etc and trowelled to a smooth finish including coved and rounded angles. *(A079 A080) 0 - 150mm girth 151 - 300mm girth 1:3 cement and sand mortar to form kerbs including trowelling smooth, form coved and rounded angles to exposed surfaces (Formwork measured separately). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A072
m2
64.10
A073
m2
5.60
A074
m2
1.30
A075
m2
2.50
A076
m2
15.80
A077
m2
8.80
A078
m2
1.20
m m m3
PAGE 8 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION FLOOR FINISHES (CONT'D) 25mm thick concrete screed (Grade 30) with 10mm maximum size aggregates to concrete floor surface finished with steel trowel. Add to (or deduct from) Item A082 for each 5mm thickness over (or under) 25mm (GRADE 30). Extra over item A077, A078, A082 & A083 for approved waterproofing compound incorporated in the screed for each 5mm thickness. Extra over manual trowelling with two passes of "Helicopter" power trowel to surface of concrete Brick-on-edge paving of red facing bricks laid on 50mm thick 1:3 cement and sand mortar screed, joints and pointing 190mm wide brick-on-edge curb in M211 bullnose/splayed edge red facing bricks and pointed in cement and sand mortar (1:3) as specified. (Cement and sand screed measured separately). Re-pointing joints of existing mosaic floor in white cement including cleaning floor on completion. Saw cut and hack to pot-hole in panel and patch up with 1:3 cement and sand mortar not exceeding 0.05 m2 per panel. 5mm thick natural quartz epoxy screed finished with 2 coats of approved epoxy colour coatings including scarifying of existing surfaces to receive the epoxy screed. 5mm thick approved epoxy screed system to concrete floor including preparation of floor surfaces (Rate include provision of 5 years warranty). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A082
m2
11.10
A083
m2
1.70
A084
m2
1.20
A085
m2
2.20
A086
m2
47.20
A087
16.90
A088
m2
4.60
A089
m2
72.60
A090
m2
42.00
A091
m2
42.60
PAGE 9 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION FLOOR FINISHES (CONT'D) 2 coats approved coloured epoxy coatings to existing epoxy floor including preparing and cleaning of surfaces to receive the coatings. 3mm thick(average) acrylic polymer cementitious coating system to ramps and driveways in multi-storey carpark. Surface of coating shall be brushed finished. Work shall be as specified in specification. * Natural aggregate concrete surface hardener to floor with 5 years warranty *(A094 A096) 5kg/m2 7kg/m2 9kg/m2 CARPENTRY AND JOINERY Sawn Kapoh, Balau,Keruing or Chengai in wall plates rafters, purlins,joists, collars, battens etc including tantalising or two coats of wood preservative. * Wrot Kapoh, Balau or Chengai *(A098 A099) Fascia or barge boards. Frame, head, mullion, transom or cill worked to the required shape. (the backs of door/window frames in contact with masonry work shall be painted with one coat wood preservative) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A092
m2
7.70
A093
m2
28.80
m2 m2 m2
A097
m3
1,323.90
A098 A099
m3 m3
3,249.10 3,024.20
PAGE 10 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CARPENTRY AND JOINERY (CONT'D) * Moulded architrave, cover fillets, etc. *(A100 A101) Not exceeding 500 sq mm in sectional area. Exceeding 500 sq mm and not exceeding 1000 sq mm sectional area. * Louver blades *(A102 A103) Not exceeding 2,000 sq mm sectional area. Exceeding 2,000 sq mm and not exceeding 4,000 sq mm in sectional area. * Timber door (Door frame, ironmongery, wood primer and painting measured separately) *(A104 A106) 38mm thick framed, ledged, braced and batten door comprising of 100 x 38mm styles and top rail, 150 x 19mm bottom ledge, 100 x 19mm middle ledge and braces filled in with 19mm thk tongued and grooved 'V' jointed boarding. 50mm thick framed, ledged, braced and batten door comprising of 100 x 50mm styles and top rail, 150 x 25mm bottom ledge, 100 x 25mm middle ledge and braces filled in with 25mm thk tongued and grooved 'V' jointed boarding. 45mm thk solid cored timber door comprising of 33mm thk tongued and grooved jointed boards fixed together with 3 nos 10mm dia. bolts and filled both faces with 6mm thk plywood lining and 19mm thk hardwood edging all round. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A100
1.80
A101
2.70
A102
3.40
A103
6.20
A104
m2
115.30
A105
m2
170.40
A106
m2
158.90
PAGE 11 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CARPENTRY AND JOINERY (CONT'D) * Louvered Door with framings stop and fill in with 13mm thick timber louvers including fixing fillets. *(A107 A108) 38mm thick. 45mm thick. * Skeleton framed flush door complying to BS 459 c/o hard wood edging all round and filled in both faces with 6mm thick plywood. *(A109 A110) 38mm thick 45mm thick 38mm thick semi-solid cored flush door with fixed timber louvres on top comprising 100 x 38mm top rail and style, 150x38mm bottom rail, 75x25mm intermediate rail and muntin, 150 x 25mm lock rail, filled in on both sides with 6mm thick plywood lining and 16mm thk timber louvres slotted and fixed to style at 60 degrees angle and spaced not more than 30mm apart. 38mm thick panel door in 4 panels filled in with 9.5mm thick plywood comprising of 100 x 38mm styles, intermediate and lock rails, 200 x 38mm top and bottom rails 45mm thick panel door in 4 panels filled in with 9.5mm thick plywood comprising of 100 x 45mm styles, intermediate and lock rails, 200 x 45mm top and bottom rails 45mm thk half hour fire-rated timber door approved by Spring S'pore & FSB c/o of solid timber core with 1.2mm thick aluminium sheet lining on both sides. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A107 A108
m2 m2
149.70 178.60
m2 m2 m2
A112
m2
104.80
A113
m2
164.10
A114
m2
188.50
PAGE 12 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CARPENTRY AND JOINERY (CONT'D) * 45mm thick fire-rated timber door approved by Spring S'pore & FSB (Door frame and ironmongeries measured separately) *(A115 A116) 1/2 hour single/double leaf 1 hour single/double leaf Extra over timber door for 100(w)x600(H)mm view panel comprising of 6mm thk georgian wired glass panel and 23 x 12mm timber beads on both sides. * 2 leave fire-rated composite timber door with wood ply finished approved by Spring S'pore & FSB c/o 2 Nos 150x300mm glass observation panels (Door frame and ironmongeries measured separately) *(A118 A119) 1 hour fire-rated 1/2 hour fire rated * Approved weather proofed (WBP) plywood in panels *(A120 A121) 6mm thick. 12mm thick. Labour & materials filling up door lock holes hinge rebates, etc including timber adhesive,sand-papering and knotting repaired surface (Painting measured separately) Repair to warped timber door by taking down, dismantle, realign, re-tightening with additional screws and refixing. Take down rotten/damaged timber frame, mullion and cills to doors/windows/vents including cutting, jointing and made good affected areas to match existing including a coat primer, one undercoat & 1 finishing coat enamel paint. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m2 m2 no
A118 A119
m2 m2
252.40 180.40
m2 m2 Door
A123
leaf
14.90
A124
24.60
PAGE 13 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CARPENTRY AND JOINERY (CONT'D) Take down decayed timber door/window, renew decayed part of members, refix to position including all necessary dowels and wedges (painting measured separately). Repair to glass door (swing type) by replacing the top pivot and bottom insert including uplifting and re-alignment of door (per leaf) To open locked door to gain access into premises where keys have been lost. IRONMONGERY * Mild Steel flat shoot bolts. *(A128 A129) 100mm. 200mm. * Brass barrel bolts *(A130 A131) 150mm. 250mm. * Stainless steel shoot bolts. *(A132 A133) 90 x 27mm barrel/square shoot bolt. 240 x 27mm barrel/square shoot bolt. 'Tiki' 200x19mm or 300x19mm stainless steel box type L/A flushbolt including dust proof socket. Mild steel pad shoot bolt with "Pad lock" locking device. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A125
m2
17.20
A126
job
108.70
A127
no
6.70
A128 A129
no no
3.20 3.70
A130 A131
no no
2.20 3.50
no no no
A135
no
3.90
PAGE 14 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) * Purpose made mild steel locking bar with 16mm diameter locking rod welded to flat handle with slot including all necessary hooks and shoots: *(A136 A139) 250mm long welded to 38 x 100 x 5mm thick flat handle. 300mm long welded to 38mm x 100mm x 5mm thick flat handle. 360mm long welded to 75 x 100 x 5mm thick flat handle. 460mm long welded to 75mm x 100mm x 5mm thick flat handle. * 4mm thick stainless steel locking eyes: complete set *(A140 A141) Single leaf door. Double leaf door. * Butt hinges *(A142 A148) 100 x 70 x 1.8 mm thick stainless steel. 102 x 76 x 2mm thick stainless steel 102 x 76 x 2.5mm thick stainless steel. 127 x 89 x 3mm thick stainless steel 2BB 75mm pressed steel. 100mm pressed steel. 150mm pressed steel. 100mm(H) x12mm diameter custom made mild steel bolt hinge to mild steel folding door. 600mm mild steel heavy duty hook and band hinges. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A136
no
10.00
A137
no
10.50
A138
no
11.20
A139
no
11.70
A140 A141
set set
17.90 20.70
no no no no no no no no
A150
no
NA
PAGE 15 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) Brass casement stays to metal casement windows. Chromium plated casement fastener complete with handle, nut, washer etc. to metal casement window. 100mm anodised aluminium 'U' shaped door handle. * Black Japanned bow handle. *(A154 A155) 100mm 150mm * Black Japanned cabin hook and eyes. *(A156 A157) 100mm. 150mm. * Hasp and staple *(A158 A162) 100mm Black Japanned. 150mm Black Japanned. 220x75x6mm thk heavy duty brass Heavy duty type for roof top trap door. 600mm mild steel heavy duty type for bin compound door. Castor wheel to metal sliding gate. PVC bearing (roller guide)to metal sliding gate. 8mm thick rubber mat as impact buffer for mild steel sliding gate including fixing accessories | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A151
no
5.90
A152
no
4.60
A153
no
1.80
A154 A155
no no
1.80 2.00
A156 A157
no no
1.00 1.20
no no no
A161 A162
no no
5.40 28.50
A163 A164
no no
27.10 47.60
A165
m2
145.40
PAGE 16 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) 12mm thick rubber mat as impact buffer for mild steel sliding gate including fixing accessories * 5-pin double cylinder mortice lockset *(A167 A169) Union 675-41-278SS, Yale 138L/520.50/ 210.62 or other approved (with handle). Union 214-SC/2.5, Yale 138L/520.50/210.62 or other approved (without handle). 'Accord 7588WO' double cylinder mortice lockset with keys complete. 'Accord 7588WO or 70mm Papiaz' double cylinder with keys to 'Accord 7588WO' mortice lockset. Roller shutter lockset ("Viro 8202/8203" or other approved). 'Accord' 608s mortice lockcase complete with stainless steel lever handle and 200 x 200mm plate. Union 1028 WE or other approved cylinder rim night latch (with handle). Rim drawback lock with deadbolt of Union 1332 or other approved (with handle). Union 2177 or other approved mortice dead lock complete with handle. Union 2295 or other approved mortice sash lock complete with handle. Union 2277 or other approved mortice sash lock complete with handle. Extra over item A174, A175, A176, A177 for rebate component. Union 9301-SS or other approved knobset with emergency release for bathroom/toilet door. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A166
m2
155.00
A167
no
81.30
A168
no
46.10
A169
no
38.30
A170
no
21.60
A171
no
46.40
A172
no
166.40
A173
no
58.80
A174
no
72.90
A175
no
28.60
A176
no
21.40
A177
no
28.60
A178
no
10.40
A179
no
20.50
PAGE 17 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) Double cylinder deadbolt (without key alike ) to handicap toilet door Double cylinder deadbolt (with key alike) to handicap toilet door Stainless steel indicating bolt (without coin opening). Mortice dead lock. (Yale M902) or other approved equivalent Rim latch with locking snib. (Union 1209 or other approved) Cylinder rim night latch. (Union 1022 or other approved) 'Yale 3202A/214.62' mortise night latch in MKAA system including keys. Latchset "Union 2642/SC/4W/rp003.BB" complete with fixing accessories Double cylinder lockset '138 Yale MD 32828' door lockset (exclude rebate). "Yale CRR8747FL US32D" entrance lock with keys. 'Yale 214.62' single cylinder thumbturn cylinder (complete with keys) 'Accord 1405-SN' single cylinder thumbturn mortice including keys. 'Accord 2332/1405' single cylinder thumbturn mortice ('Key-alike') stainless steel night latch. "Accord CH-382" stainless steel cup handle passage latch with cup handle on both sides. Extra over "Accord CH-382" stainless steel cup handle passage latch for brass rebate. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A180
no
12.50
A181
no
19.80
A182
no
11.90
A183
no
28.80
A184
no
21.20
A185
no
47.80
A186
no
91.00
A187
no
37.10
A188
no
92.30
A189
no
81.40
A190
no
47.20
A191
no
34.70
A192
no
59.60
A193
no
37.60
A194
no
14.60
PAGE 18 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) 'Union 2241' key cylinder with keys Aluminium finish mortice lever lockset to metal grille gate. (Yale L315A/M246/2 1/2" or other approved) "Tri-circle 265" 50mm padlock Crescent lock with key to aluminium sliding window. Brass cupboard/drawer lock of approved type Indicating bolt for toilet door. (Union 8098 or other approved). Cam lock for letter box (Abloy 2373, Yale 490 or other approved). Letter box lockset for postman. 'C-S1' or other approved spring lock to dry riser breeching inlet cabinet. 38mm diameter 25mm thick rubber door stop. 'Tiki 90 series, NHN Model 1082, New Star 5002, 'Accord 93' or other approved equivalent slimline door closer with cushioned back checking action 'YTL-60' brass ball catch. 'YTL-DS002S' stainless steel spring loaded dust proof socket. Door closer "Dorma TS 7301" size 3 hold open arms. Door closer 'Dorma 8815' stainless steel level handle. Duplicate key to match existing. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A195 A196
no no
26.20 29.80
A197 A198
no no
7.30 13.00
A199
no
9.90
A200
no
14.10
A201
no
13.20
A202 A203
no no
24.60 21.70
A204
no
2.60
A205
no
67.20
A206 A207
no no
1.90 3.40
A208
no
131.30
A209
no
63.80
A210
no
2.30
PAGE 19 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) Duplicate sub-master key for 'Yale MK48' using original 'Yale' blank key. 300mm long chain with bracket and ring to metal box/door etc. for padlock. * Accessories to steel sliding and folding doors of workshops. *(A213 A235) "Abloy 4960" complete with keys or equal and approved. "Henderson 67/89" intermediate roller guide. "Henderson 67/97" intermediate roller guide. "Henderson 67C/97" intermediate roller guide. "Henderson 68/89" end roller guide. "Henderson 68/97" end roller guide. "Henderson 68C/97" end roller guide. "Henderson 62K" intermediate hanger. "Henderson 62A" intermediate hanger. "Henderson 62C" intermediate hanger. "Henderson 63K" end hanger. "Henderson 63A" end hanger. "Henderson 63C" end hanger. "Henderson 97" steel channel. "Henderson 1A/290" heavy duty alloy bracket including all necessary bolt drilling and painting. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A211
no
38.00
A212
no
4.00
A213
no
159.10
A214
no
30.00
A215
no
30.00
A216
no
86.20
A217 A218 A219 A220 A221 A222 A223 A224 A225 A226 A227
no no no no no no no no no m no
21.20 22.10 51.70 48.10 58.30 167.40 39.10 53.40 95.40 25.70 12.60
PAGE 20 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION IRONMONGERY (CONT'D) "Henderson 1A/301" heavy duty alloy bracket including all necessary bolt drilling and painting. "Henderson 1A/305" heavy duty alloy bracket including all necessary bolt drilling and painting. "Henderson 290" galvanised track. "Henderson 301" galvanised track. "Henderson 305" galvanised track. "Henderson 994R" 380mm galvanised steel shoot with brass roller "Henderson 65" back flap hinges. "Henderson 65C" back flap hinges. STRUCTURAL STEELWORK & METALWORK * Lift Certificate holder *(A236 A237) 170mm x 220mm x 5mm clear perspex sheet with polished edges and 4 Nos stainless steel 'philip' head self tapering screw. 170mm x 220mm x 5mm clear perspex sheet with 13 x 5 x 13mm aluminium 'U' channel framing fix to lift car by pop-riveting. Brass roller to roof top access trap door. Metal rails to roof top access trap door. 1mm thick aluminium sheet as cover, linings and flashing to roof trap door including bending and fixing accessories. 5mm thick stainless steel eye anchor of internal diameter 15mm of Grade A1S1 304 including epoxy putty and nylon plug. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A228
no
21.00
A229
no
42.00
m m m no
A234 A235
no no
21.20 83.40
A236
no
8.30
A237
no
24.00
A238
no
16.40
A239
18.90
A240
m2
25.70
A241
no
2.20
PAGE 21 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) Flag Pole holder hot dipped galvanised comprising of 40mm diameter pipe welded to 5mm thick plate to detail bolted to concrete surface with 10 x 90mm 'Hilti HSAR' or approved anchor bolt. Flag Pole holder hot dipped galvanised comprising of 31 x 31 x 2.3 mm thick square hollow section to detail bolted to concrete surface with 10 x 90 mm 'Hilti Hsar' or approved anchor bolt. Mild steel Grade 43A to BS 4360 for flats, angles, tees,channels, hollow sections, square sections, rivets and bolts, etc. of any size fabricated and fixed including welding or bolting, and painting with one coat of lead and chromate-free primer (structural steel work only) Mild steel flats, angles, tees, channels, rviets and bolts, etc. of any size fabricated and fixed including welding or bolting (for non-structural steel work only) Extra over mild steel rods, flats, angles, tees, channel, hollow sections, rivets, bolts, etc for galvanising in lieu of painting on coat of lead and chromate-free primer. Extra over mild steel rods, flats, angles, tees, channels, hollow sections, rivets, botls, etc. for galvanising 100mm diameter x 6mm thick mild steel hollow section bollards with complete with 6mm thick end cap and 200 x 200 x 6mm thick base plate with stiffener including all necessary welding and painting with 1 primer coat and two coats of enamel paint. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A242
no
44.10
A243
no
43.60
A244
kg
4.60
A245
kg
4.00
A246
kg
0.70
A247
kg
0.90
A248
no
64.50
PAGE 22 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) Spot welding loose / corroded metal work 3mm thick hot-dipped galvanised mild steel chequered plate cut to size and welded to mild steel works. Welded steel fabric RN 228 to vent including all necessary cutting and welding (painting measured separately). Galvanised mesh no. 5518 fixed to openings (excluding frame). 2mm thick perforated aluminium sheet 2mm thick aluminium sheet fixed to frame including fixing accessories(Frame and painting measured separately). * Mild steel vertical trap grating to 250 /300mm wide surface water channel of the following depth comprising 10mm diameter vertical bars spaced 38mm centre, all framed up and welded to 25mm x 25mm x 5mm thick angle horizontal top piece and 25mm x 5mm thick flat intermediate piece, the ends of horizontal top piece split and fixed to sides of channel including 1 priming coat and 2 coats of enamel paint.*(A255 A256) Not exceeding 450mm deep Exceeding 450mm but not exceeding 750mm deep. Labour and materials for refixing fallen bicycle stands | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A249
no
1.00
A250
m2
79.40
A251
m2
9.20
A252
m2
7.70
A253 A254
m2 m2
49.30 44.00
A255 A256
no no
19.10 21.10
A257
no
5.70
PAGE 23 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) Standard bicycle parking rack comprising of 0.63m x 65mm diameter mild steel pipe welded at top diameter mild steel pipe welded at top 480mm above ground level, the other end embedded 150mm deep in concrete (1:2:4) with 2 nos of 0.84m x 13mm diameter mild steel bar bent and welded for single side parking including 3 coats of oil paint and making good etc. Standard bicycle parking rack comprising of 1.68m x 13mm diameter mild steel bar for double sides parking. * 'Hilti-HAS' or other approved adhesive anchor including drilling holes and all necessary preparation according to manufacturer's instruction ( Chemical capsule measured separately). *(A260 A263) 8mm diameter x 80mm length anchor 10mm diameter x 90mm length anchor 12mm diameter x 110mm length anchor 16mm diameter x 126mm length anchor * Chemical Capsule 'Hilti' or other approved equivalent to manufacturer's instruction. *(A264 A267) Hilti HVU M8 Hilti HVU M10 Hilti HVU M12 Hilti HVU M16 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A258
no
27.20
A259
no
28.30
no no no no
no no no no
PAGE 24 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) * Galvanised medium duty expansion anchor bolt 'Hilti HAS-KA' or other approved equivalent including stud anchor, nut and washer *(A268 A273) 6mm diameter x 65mm length 8mm diameter x 75mm length 10mm diameter x 90mm length 12mm diameter x 110mm length 16mm diameter x 145mm length 20mm diameter x 170mm length 20mm diameter galvanised heavy duty expansion anchor bolt 'Hilti HSL' or other approved equivalent including stud anchor, nut and washer. Ramset nail including the use of gun and explosives. Ramset threaded stud including the use of gun and explosive. 25 x 3 x 230mm long steel holdfast. Cut into existing wall and incorporate new 25 x 3 x 230mm long steel holdfast including filling up hole with 1:3 cement mortar and painting/tiling to match. Pop Rivet to aluminium louvre blades or other aluminium fittings. Gauge 18 standard approved aluminium w.c. or bathroom doors 800mm wide x 1800mm height, including hook and band hinges and cabin hook. To re-fasten loose hinges of aluminium door including screw and rivet if necessary. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no no no no no
A275
no
0.40
A276
no
0.80
A277 A278
no no
1.80 4.40
A279
no
0.40
A280
no
108.10
A281
leaf
2.80
PAGE 25 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) Single leat PVC w.c or bathroom door of approved type door opening not exceeding 900 x 2090 height including lockset and necessary fixtures. Gauge 20 purpose-made galvanised sheet expansion joint cover 150mm wide the "V" shaped groove in centre including fixing with masonary nails and washers at 150mm centres at both edge. Take out loose galvanised steel expansion joint and repair to cracked/ chipped wall and refix with masonary nail with washer at 150mm centres at both edge. Natural anodised aluminium letter box, size 400 x 270 x 144mm / 380 x 270 x 150mm/380/270/110mm fabricated in accordance with HDB's standard drawings including locks and keys, engraving with unit numbers (masonry work measured separately). Anodised aluminium letter box flap complete with engraving of unit numbers to match existing. Two-way natural anodized aluminum letter box, o/a size 270 x 150 x 400mm, including master door, locks and keys and engraving with unit numbers, block numbers and street name * 1.2mm thick natural anodised aluminium roller shutter complete with all necessary components in accordance with manufacturer's instructions, fixing accessories and removal of existing if any. *(A288 A290) Manual operated. Chain operated. Motorised operated. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A282
no
58.00
A283
6.80
A284
5.30
A285
set
141.80
A286
no
24.70
A287
no
172.50
m2 m2 m2
PAGE 26 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) 4 hours fire-rated electric operated roller shutter galvanise finished c/w ironmongeries and fixing accessories etc complete including commissioning(Spring S'pore & FSB approved fire-rated) Roller shutter bearing 100mm diameter x 20mm width including reset system to function. Replace chain block of roller shutter door including adjusting shutter's aligment, tightening of loosen parts and greasing. Supply labour, tools and stagging (if necessary) for dismantling and cart away existing roller shutter. Remove existing damaged roller shutter and replace with electrically operated 1 hour fire rated shutter curtain, complete with electric motor, powder coating according to FSB 476 P22, fusible link mechanism, side guide, hand chain, bottom bar, PSB approved fire door certificate and tested to SS489, 2001, including all other necessary accessories Roller shutter IC card including reset to function. PVC weather seal to roller shutter 45mm thick mild steel sliding and folding door constructed of 1.6mm thick plate(preformed and bend to shape in factory) including timber packing piece, mild steel angles, locking eyes, floor channels and shoot bolts (All hanging track, guide and ironmongeries not specified shall be measured separately.) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A291
m2
315.70
A292
no
109.30
A293
no
517.50
A294
job
391.00
A295
m2
359.40
A296
no
281.80
A297 A298
m m2
3.20 163.40
PAGE 27 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) * Fire-rated steel door with approved steel frame, 125mm stainless steel butt hinges, door closer and mortise lock ('Spring' approved fire-rated with label) (Painting measured separately) *(A299 A300) 1 hour fire-rated 2 hours fire-rated 1/2 hour fire-rated heavy duty aluminium door c/o aluminium extruded section frame, ironmongeries and panic hardware from inside(PSB approved fire-rated) 4 hours fire-rated heavy duty aluminium door c/o aluminium extruded section frame, ironmongeries and panic hardware from inside (PSB approved fire-rated) 4 hours fire-rated heavy duty aluminium louvre door fitted with panic hardware from inside, ironmongeries, fixing accessories and door frame complete (PSB approved fire-rated) Provide labour, tools and sundries to take down existing mild steel sliding and folding door to overhaul, cease, adjust and grease all parts. Repairs and replacement to corroded section of door including necessary welding and to reinstall to slide properly.(Replacement of ironmongery item measured separately) Labour to weld back metal gate padlock eye. Labour taking down mild steel gates/ metal grilles including removal of bolts and patch up holes | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m2 m2 m2
A302
m2
977.60
A303
m2
1,073.00
A304
m2
5.50
A305
no
3.50
A306
m2
5.70
PAGE 28 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) * Aluminium adjustable lourved window frames comply with SS212 for louvres per set including rattleproof spring clips and all necessary bolts and nuts and fixed at wood, concrete or brick etc.(Measurement shall be height per light and louvres blades measured separately). *(A307 A309) Natural anodised and single control. Natural anodised and dual control. Bronze anodised and single control Extra over single/double control aluminium adjustable louvre window frame complying to SS 212 for burglar bar (Measurement shall be by height of window per light). * Galvanised steel adjustable louvred windows frames for 150mm wide glass or aluminium lacquered louvres per set including rattleproof spring clips and all necessary bolts and nuts and fixed at wood, concrete or brick etc. (Measurement shall be height per light and louvres blades measured separately). *(A311 A314) Single control Single control and burglar proof type. Dual control. Dual control and burglar proof type. 10mm square galvanised burglar proof bar to louvred window. 1.6mm thick extruded aluminium louvred 5 blades size not exceeding 600mm x 150mm wide in anodised finish to fixed/ adjustable louvred window. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m m m m
m m m m m
A316
no
6.40
PAGE 29 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) Fix re-used metal louvre blade to adjustable louvre window including removal of existing if any. Powder coated aluminium fixed louvred vent c/o 5mm thk tinted glass, alum framing, ironmongery and cill, cement mortar infill and all necessary fixing and jointing accessories. Repair to adjustable louvre window including the use of all necessary fitting parts, easing of window, dismantle and refixing all frames and louvres. (Regardless of height) Bronze anodised extruded aluminium framed casement window with sheet float glass, aluminium fronting, ironmongery and cill with cement mortar infill and all necessary fixing and jointing materials and accessories as specified with 5mm thick clear sheet float glass. Natural anodised extruded aluminium framed casement window with sheet float glass, aluminium fronting, ironmongery and cill with cement mortar infill and all necessary fixing and jointing materials and accessories as specified with 5mm thick clear sheet float glass. Repair to mild steel casement window frame, sash and hinges including all necessary cutting, welding, refixing of glass panel and painting to match existing. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A317
no
1.20
A318
m2
123.40
A319
Light
3.50
A320
m2
180.00
A321
m2
236.10
A322
light
8.80
PAGE 30 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) * Aluminium extruded frame top-hung window complete with glass, aluminium framing, ironmongery and cill with cement mortar infill and sealant joint and fixing accessories as specified: *(A323 A326) Natural anodised with 5mm thick float clear glass Natural anodised with 5mm thick float tinted glass Bronze anodised with 5mm thick float clear glass Bronze anodised with 5mm thick float tinted glass * Aluminium extruded framed fixed window panel c/o glass, aluminium framing, ironmongeries, cill, cement mortar infill, sealant joint. *(A327 A330) Powder-coated with 5mm thick clear float glass Natural anodised with 5mm thick clear float glass Bronze anodised with 5mm thick clear float glass Bronze anodised with 5mm thick tempered glass Stainless steel stair nosing size 50mm x 35mm x 0.8mm thick of grade 304 bedded in cement mortar 1:3. 1100mm height fluorocarbon coated fluorocarbon coated alum sun breaker. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A323
m2
350.20
A324
m2
360.70
A325
m2
378.60
A326
m2
280.00
A327
m2
286.90
A328
m2
256.20
A329
m2
277.00
A330
m2
339.50
A331
11.60
A332
202.00
PAGE 31 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION STRUCTURAL STEELWORK & METALWORK (CONT'D) 1.0m high stainless steel railing c/o 50mm dia X 2mm thick pipe as top rail, intermediate, bottom rail and the same for baluster but @ 1.2m c/c, infilled with 12mm dia, x 1.2mm thick s/s pipe @ 100mm c/c cast in concrete 38mm diameter stainless steel handrail complete with end flanges, covers and fixing accessories. Rubberised bollard (Black) 152mm diameter x 900mm height complete with mild steel cover to conceal bolts. 100mm diameter x 6mm thick mild steel hollow section bollards with 200mm of its length encased in 350 x 350 x 350mm deep grade 20 concrete foundation and 900mm of its length above ground level complete with 6mm thick end cap and 200 x 200 x 6mm thick base plate with stiffener including all necessary welding and painting with 1 primer coat and two coats of enamel paint. 6mm diameter galvanised chain to bollards including all fixtures. Supply and install 10mm galvanised linkchain complete with D-shackles and clear PVC tubing. 256 x 256mm galvanised steel lightning conductor pit cover complete with a 12mm diameter hole and hinges. Supply of cylinder oxygen Supply of cylinder acetylene | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A333
307.50
A334
NA
A335
no
386.40
A336
no
77.80
A337
3.00
A338
11.10
A339
no
4.10
A340 A341
no no
16.10 51.80
PAGE 32 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SIGNAGES Plastic unit number plate 40 x 60mm per digit 700 x 200 x 2mm thick directional aluminium sign plate fixed to wall with approved stainless steel screws and plugs. 200mm (H) street name sign consisting of 2mm thick aluminium plate of Engr's grade reflective sheet with vinyl film non reflective alphabets/nos on both face, 50.8 x 50.8 x 4mm Galvanised SHS pole and 350 x 350 x 500mm G20 concrete foundation. 2mm thick natural aluminium sign plate with helvetica letters, numbers, symbols, logo etc engraved/embossed in approved colour including stainless steels fixing screws/bolts to walls /post. 2mm (14 SWG) sign plate with high intensity grade reflective sheet, letterings, figures and graphics mounted to one face installed to wall/post etc including stainless steel fixing screws/ bolts. (Post measured separately) 3mm thick aluminium HDB standard sign sign plate consisting of embossed block number and lift emergency number of approved colour to lift lobby walls including stainless steel fixing screws/bolts. 3mm thick aluminium sign plate with embossed and reflective paintwork (yellow letterings/numbers with black background) including stainless steel fixing screws/bolts. 300x400mm aluminium standard danger warning sign plate for 415V consumer switchroom with approved silkscreen vinyl. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A342
no
1.00
A343
no
24.20
A344
no
345.30
A345
m2
347.50
A347
m2
349.10
A348
m2
241.40
A349
m2
267.40
A350
no
16.20
PAGE 33 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SIGNAGES (CONT'D) 1.5mm thk stainless steel lift notice plate with helvetica letters, numbers, symbols, logo etc engraved/embossed in approved colour including stainless steels fixing screws/bolts to walls at lift lobby. * Aluminium 'Box' lettering with black matt finish paint. *(A352 A355) 25mm thick (150mm - 250mm height) 30mm thick (>250mm - <=350mm height) 30mm thick (>350mm & <=400mm height) 30mm thick (>400mm & <=500mm height) * Acrylic sign plate of approved design c/o graphics, text(alphabets, numerals), logo, colours etc with approved stickers or spray paint including fixing stainless steel screws/bolts and accessories. *(A356 A360) 2mm thick (not exceeding 0.10m2) 2mm thick (exceeding 0.10m2) 3mm thick (not exceeding 0.10m2) 3mm thick (exceeding 0.10m2) 10mm thick 5mm thick acrylic lift information sign plate of approved design in 4 languages c/o approved sticker or spray paint including stainless steel fixing screws and accessories. 6mm acrylic sheet signage with bend edges c/o approved sticker of building layout plan in approved colour at lift lobby including stainless steel fixing screws/bolts. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A351
m2
251.20
no no no no
m2 m2 m2 m2 m2 m2
A362
m2
782.70
PAGE 34 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SIGNAGES (CONT'D) 10mm thick "Ultimate Flexi Sign" perplex sign plate c/o text/text (alphabets, numerals, etc.) in approved colour, stainless steel fixing screws and accessories. Red colour triangle fire access sticker (approved by FSSB) Vinyl sticker of approved waterproof type with graphics, letters, numbers, symbols etc to sign plate. Vinyl sticker of approved waterproof type with 'cut-out' letterings, numbers, symbols etc to sign plate (Measurement shall be by the perimeter of the complete set of the 'cut-out'). Update directory signs for new tenant complete with Unit Nos and Company's Name including removal of redundant signs if any. The types, size and numbers of alphabets and numerals shall be to match existing and regardless of the numbers of alphabets or numerals and the type of design and material used. Remove aluminium plate (any size) from walls and return to HDB office on instruction of SO's Representatives including making good works disturbed. 50 x 50 x 4mm thick mild steel square hollow section stand (2.20m from ground level to underside of signboard and 0.5m below ground level) with 200 x 200 x 6mm thick base plate welded to stand, 350 x 350 x 450mm Concrete (grade 20) foundation including fixing accessories. 1140(L)x840(H)mm notice board 'Gleason' or other approved equivalent at lift lobby. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A363
m2
907.70
A364
no
6.70
A365
m2
144.90
A366
m2
181.10
A367
no
10.50
A368
no
11.70
A369
no
88.00
A370
no
362.30
PAGE 35 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING RN 3315 to roof to support sisalation paper. 50mm thick Fibreglass (Building Grade) insulation to roof. Sisalation 436 double sided aluminium foil. * Rock/Mineral Wool roofing insulation including fixing accessories to roof : *(A374 A377) 50mm thick (40kg/m3) 50mm thick (50kg/m3) 50mm thick (60kg/m3) 50mm thick (80kg/m3) 50mm thick poly fibreglass wool blanket (Density: 10kg/m3) to underside of metal roof 0.47mm thick colourbond Spandek Hi-Ten metal roofing sheets including all necessary accessories as specified. 0.47mm thick 'Multi-deck XRW' colourbond roofing sheet including all fixing accessories (including provision of 10 years warranty) 0.53mm thick colourbond Kliplok Hi-Ten metal roofing sheets including all necessary accessories as specified. 0.65mm thick colourbond Kliplok Hi-Ten metal roofing sheets including all necessary accessories as specified. 0.47mm thick colourbond V-Crimp Hi-Ten metal fascia sheets including all necessary fixing accessories as specified. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A371
m2
3.50
A372
m2
6.90
A373
m2
5.00
m2 m2 m2 m2 m2
A379
m2
30.20
A380
m2
44.70
A381
m2
35.20
A382
m2
40.70
A383
m2
35.60
PAGE 36 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING (CONT'D) 0.53mm thick Speed deck 508 colorbond XRW metal roofing sheets including all necessary accessories as specified 0.65mm thick Speed deck 508 colorbond XRW metal roofing sheets including all necessary accessories as specified 0.60mm thick colourbond standard ridge capping to Kliplok roofing including all necessary fixing accessories as specified. 0.60mm thick custom made colourbond flashings/cappings/trims to Kliplok roofing including all necessary fixing accessories as specified. 0.8mm thick PVF2 coated Rannila 45J roof sheet including fixing accessories 0.8mm thick PVF2 coated panel to eave/verge flashings including fixing accessories (350mm girth) 50mm thick poly fibreglass wool blanket reflective roof heat insulation sheet including lapping with 'Parsec Thermo brite' tape and secured to roof structure by self-drilling fasteners with metal washers in accordance with manufacturer's instructions. Lay one layer of 'Super-Brite' radiant vapour barrier reflective roof heat insulation sheet including lapping with PPC 493 reinforced aluminium foil tape and secured to roof structure by self-drilling fasteners complete with metal washers as specified and in accordance with Manufacturer's instructions. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A384
m2
53.60
A385
m2
60.50
A386
19.90
A387
21.10
A388
m2
39.90
A389
21.70
A390
m2
7.80
A391
m2
7.30
PAGE 37 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING (CONT'D) Labour to take out and reinstall existing roofing sheets including provision of approved new fixing accessories if any for the replacement of insulation system. Lay tarpaulin to roof damaged by fire including timber battens and fixing accessories to hold down tarpaulin. Supply and lay felt roll to roof including fixing screws. * 20 Gauge(0.914mm) galvanised steel rain-water eaves gutters fabricated and fixed including all necessary fixing accessories, painting one coat of approved zinc chromate to all surfaces and one coat of approved water-proofing coating to the internal surface of the gutter and 1 primer coat and 1 finishing coat of enamel paint externally (mild steel brackets measured separately) *(A395 A398) Not exceeding 0.5m girth. Exceeding 0.5m but not exceeding 0.75m girth. Exceeding 0.75m but not exceeding 1.00m girth. Exceeding 1.00m but not exceeding 2.00m girth. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A392
m2
3.50
A393
m2
1.70
A394
m2
5.80
A395 A396
m m
21.30 27.70
A397
32.30
A398
39.10
PAGE 38 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING (CONT'D) * 1mm thick approved 'zincalume' gutters fabricated and fixed including fixing accessories, painting one coat of approved zinc chromate to all surfaces and one coat of approved waterproof coating to internal surface of the gutter and 1 primer coat and 1 finishing coat of enamel paint externally (mild steel brackets measured separately) *(A399 A402) Not exceeding 0.5m girth Exceeding 0.5m but not exceeding 0.75m girth Exceeding 0.75m but not exceeding 1.00m girth Exceeding 1.00m but not exceeding 2.00m girth 150mm diameter gauge 16 half-round galvanised steel rainwater eaves gutters including brackets and all necessary fixing accessories, painting internally with 1 coat approved waterproofing coatings and 1 primer coat and 1 finishing coat of enamel paint externally Repair to leaking metal roof/gutter with approved polyurethane sealant to all bolt heads and leaking joints/gaps and apply 'Emer Clad' or other approved waterproofing coatings with minimum thickness of 300 microns to surfaces of roof/internal of gutter. * Labour for refixing and repair lose flashing including all necessary additional drive screws *(A405 A406) Not exceeding 300mm girth. Exceeding 300mm girth. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A399 A400
m m
31.10 52.30
A401
66.80
A402
98.00
A403
22.70
A404
m2
8.10
A405 A406
m m
3.10 4.20
PAGE 39 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING (CONT'D) Repair to loose/dented metal roof flashing/facia including approved fixing screws/accessories Remove existing gutter, brackets, RWDP, holders etc including cutting, cart away and make good disturbed areas to match existing (Rate include dumping fees & stagging) Lay 600 x 600 x 30mm thick ferrocement secondary roof slabs, reinforced with galvanised welded fabric to concrete flat roof including all necessary supporting concrete solid block (Hoisting by crane shall be measured separately). Apply a complete Waterproofing Membrane System to concrete flat roof consisting of 6 coats of waterproofing membranes, 1 layer of fibre glass membrane and 1 coat of bituminous aluminium finishing paint as specified; complying with SS133:1987 and in accordance with manufacturer's instructions Panel Roofing System to roof surfaces consisting of 38mm thick waterproofing cement and sand panel (1:3), 50mm thick 'Roofmate' insulation board, 6 coats of waterproofing membranes, 1 layer of fibre glass membrane and a minimum of 20mm thick waterproofing cement sand screed (1:3) laid to fall Removal of existing waterproofing bituminous membrane, stools and secondary slabs and prepare surfaces to receive new membrane including hoisting down debris and disposal. Removal of existing waterproofing membrane and prepare surfaces to receive new membrane including hoisting down debris and disposal. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A407
m2
4.20
A408
3.80
A409
m2
14.80
A410
m2
8.10
A411
m2
52.50
A412
m2
5.30
A413
m2
2.40
PAGE 40 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION ROOFING (CONT'D) Temporary removal of existing precast concrete secondary roof slab and support to facilitate repair works and relay the existing precast concrete secondary roof slab and support upon completion on repair works. Concrete ridge tiles (all colours) in repairs including stripping off existing and removing debris off site. Patch up nail holes in corrugated roofing sheets with mastic and one layer of bituminous felt. Rake out bitumen or other compounds from existing roof expansion joints and refill with approved sealing compound including backer rod. G20 (0.914mm thick) purpose-made aluminium expansion joint cover not exceeding 500mm girth with "V" shaped groove in centre including fixing with stainless steel screws and washers WALL & CEILING FINISHES Hack off wall finishes, form keys, clean and wash to receive new finishes including cart away debris to dumping ground * 18mm thick plaster with approved prepacked mortar mix in 2 coats to wall: *(A420 A421) Applied from within building Applied from external of building | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A414
m2
1.40
A415
no
11.10
A416
no
0.30
A417
6.40
A418
6.30
A419
m2
4.30
A420 A421
m2 m2
18.70 21.00
PAGE 41 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION WALL & CEILING FINISHES (CONT'D) * Skim coat with approved skimming material. *(A422 A425) Wall (from within building) Ceiling (from within building) Wall (from external of building) Sides and soffit of beams and slabs (from external of building) Exmet mesh to wall * Wall tiles of approved colours, patterns and textures including prepacked mortar screed as specified. *(A427 A428) 7mm thick white glazed ceramic tiles 8mm thk glazed wall tiles (SS301.1985) 9mm thk homogeneous wall tiles as specified including grinding down of sharp corners to a rounded edge and prepacked mortar screed as specified. Re-pointing joints of existing wall tiling in white cement including cleaning surface on completion. 200 x 100mm thick natural rubber bumper to wall of loading/unloading bay including all approved fixing accessories * 1200mm high rubber protection guard fabricated to corners of wall/column complete with 20 nos. of stainless steel (SUS304) HPS capsule boltings. *(A432 A433) 75 x 75 x 10mm thick. 100 x 100 x 10mm thick. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m2 m2 m2 m2
A426
m2
3.20
m2 m2 m2
A430
m2
1.90
A431
212.80
A432 A433
no no
39.10 50.60
PAGE 42 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION WALL & CEILING FINISHES (CONT'D) 150mm width x 30mm thick natural rubber bumper to skirting areas of lift lobby including all approved fixing accessories. 1200mm height rubber protection guard of size 75 x 75 x 6mm thick to corners of wall /column complete with 10 Nos of galvanised steel HPS capsule boltings. Rubberised Studded Band including including all fixing accessories. Remove bolts, and anchor stud of fixtures below concrete/plaster surface including patch up holes with approved non-shrink cement grout including necessary painting to match existing. * Boards to ceiling/wall etc. (Frames measured separately) *(A438 A442) 6mm thick fibre reinforced cement board. 10mm thick fibre reinforced cement board. 12mm thick fibre reinforced cement board. 10mm thick gypsum board. 12mm thick mineral fibre board. 9.5mm thk approved gypsum ceiling boards including suspension system (exclude removal of existing suspended ceiling). 600x600x15mm thick 'Armstrong' pin dot mineral fibre ceiling on exposed white T-grid c/w hangar rod and clips | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A434
61.00
A435
no
31.10
A436
44.90
A437
no
0.50
A438 A439
m2 m2
7.50 11.00
A440
m2
14.50
m2 m2 m2
A444
m2
41.00
PAGE 43 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION WALL & CEILING FINISHES (CONT'D) Aluminium approved patterned recessed panel ceiling of grid 600x600x0.7mm thick clip-in panel concealed joint and powder coated to colour. The ceiling shall consist of bevelled edged tiles fixed to an adjustable suspension system. 0.8mm thick fluorocarbon/electrostatic powder coated 'Dampa-Tile' 600 x 600mm aluminium ceiling c/o combination aluminium plain flat and perforated ceiling tiles, approved metal suspended system and fixing accessories. Grid suspension system (600 x 1200mm grid) c/o 'T'/'L' shaped galvanised steel strips not exceeding 30mm wide as fillet for false ceiling including hanging lines. Labour, tools and mobile scaffold if necessary to remove suspended ceiling including make good disturbed area, cart away and disposal. PAINTING AND DECORATING * Painting surfaces of wood and metal surfaces with synthetic enamel paint including preparation of surfaces *(A449 A450) One finishing coat. One undercoat and one finishing coat. Prepare and apply one coat 'Co-Seal' fleck coat base and finishing coat of 'Co-Seal' econocoat plastic emulsion paint to internal wall and ceiling Prepare and apply one coat 'Co-Seal' binder/sealer, one undercoat of 'Co-Seal' liquid plastic dressing and one finishing coat of 'Co-Seal' liquid plastic dressing to plastered external wall | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A445
m2
40.30
A446
m2
63.30
A447
m2
7.30
A448
m2
1.20
m2 m2 m2
A452
m2
13.10
PAGE 44 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION PAINTING AND DECORATING (CONT'D) Brush or wash down and apply 2 pack (1 coat) mix polyurethane paint (non-metallic finishes) on concrete or plastered surface Brush or wash down and apply polyurethane enamel paint c/o ; 1 coat of amino epoxy zinc phospate blast primer, amine epoxy matt, 2 pack polyurethane undercoat and 2 pack polyurethane finishing coat to steelwork Remove rust, clean down and apply one coat approved rust convertor to metal surfaces Clean and paint one coat zinc chromate primer to metal surfaces. Clean down, knotted stopped, sand papered smooth and prime one coat aluminium primer to wood surfaces One coat red primer (anti-corrosive) Type 'C' to metal surfaces including preparation of surfaces as specified. Remove rust, clean down and apply one coat approved cold zinc galvanise paint (glossy type) to metal surfaces. One coat approved epoxy paint to metal surfaces. Painting to both faces with one finishing coat synthetic enamel paint including preparation of surfaces as specified. (Measured flat on its elevation surface) Metal grilles/staircase railings One coat approved oil base luminous epoxy paint to metal surfaces. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A453
m2
2.20
A454
m2
10.10
A455
m2
1.00
A456
m2
1.40
A457
m2
1.40
A458
m2
1.50
A459
m2
3.00
A460
m2
1.80
A461
m2
2.20
A462
m2
7.70
PAGE 45 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION PAINTING AND DECORATING (CONT'D) * Painting pipes, railing, etc. with synthetic enamel paint including preparation of surfaces as specified. *(A463 A466) One finishing coat (not exceeding 75mm diameter). One undercoat and one finishing coat. (not exceeding 75mm diameter). One finishing coat. (Exceeding 75mm diameter and not exceeding 150mm diameter). One undercoat and one finishing coat. (exceeding 75mm and not exceeding 150mm diameter). * Brush with steel wire brush to remove all rust, prepare and paint two coats approved bituminous paint to pipe surfaces *(A467 A469) Not exceeding 75mm diameter Exceeding 75mm diameter but not exceeding 150mm diameter Exceeding 150mm diameter but not exceeding 300mm diameter * Painting metal lamp guard and fluorescent tube casing with one finishing coat synthetic enamel paint. *(A470 A471) 600mm long. 1200mm long. Painting one finishing coat aluminium paint to metal adjustable louvred window blades. (Rate inclusive of painting to both faces) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A463
0.50
A464
0.80
A465
1.10
A466
1.90
A467 A468
m m
1.00 2.10
A469
4.10
no no no
PAGE 46 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION PAINTING AND DECORATING (CONT'D) Painting one finishing coat aluminium paint to metal collapsible gates. (Measured flat over area of gates. Rate inclusive of painting to both faces). Prepare and paint one coat of aluminium paint to adjustable louvered frame (Both faces). * Paint approved acrylic emulsion paint to surfaces of walls, ceilings, columns, etc including preparing surfaces as specified. *(A475 A476) One finishing coat (without dilution). One under coat (with 20% dilution) and one finishing coat(without dilution) Brush, wash down and apply one coat water-based sealer on concrete or plastered surfaces. One coat approved anti-bacteria paint to wall Two coat Shellac varnish to wood surfaces. One coat approved bituminous paint to mild steel gratings (rate inclusive of both faces). GLAZING * Glass louvres with polished edges to metal/timber frames. *(A481 A482) 6mm thick clear glass. 6mm thick obscured wired glass. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A473
m2
2.90
A474
0.40
A475 A476
m2 m2
1.10 2.00
A477
m2
0.80
A478
m2
2.40
A479
m2
2.00
A480
m2
7.70
A481 A482
m2 m2
61.90 71.30
PAGE 47 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION GLAZING (CONT'D) * Glass panels to metal/timber casement windows and vents including putty and necessary accessories *(A483 A484) 5mm thick clear glass. 6mm thick clear glass. Fix re-used glass louvred to adjustable louvred window/vent including removal of existing. FIRE EQUIPMENT Fire hose 'Miros Commander Super' or approved equivalent c/w 64mm diameter x 30m long, fibre glass casing with 75mm x 50mm galvanised 'C' channel. Hose reel cabinet overall size 800 x 800 x 400mm depth 16G electro-galvanised steel cabinet complete with red powder coating mounted to wall. Hydraulic double pivots hosereel drum of approved swing type c/w fixing accessories. 25mm diameter single braided hose approved by FSB complete with clips. Controllable discharge nozzle to 25mm diameter hose. 3mm thick clear glass to fire hosereel and fire extinguisher cabinet including fixing accessories (Frame measured separately) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m2 m2 no
A486
no
402.50
A487
no
250.40
A488
no
177.00
A489
3.80
A490
no
42.30
A491
m2
22.90
PAGE 48 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION REINSTATEMENT OF WATER/ELECTRICITY WORK Supply labour to remove, cut off supply, diversion and reinstatement of water supply within internal/outside unit.(additional new material used shall be measured separately) Supply labour to remove, diversion and reinstatement of electrical (Lighting/ Power point) supply. (additional new material used shall be measured separately) Termination of electricity supply from tap-off unit to tenant's DB by licensed electrical worker including removal of cables, trunkings/conduits/trays and make good disturbed areas to match existing. Termination of electricity supply from HDB's switchroom to tenant's DB by licensed electrical worker including removal of cables, trunkings/conduits/trays and make good disturbed areas to match existing. Termination of electricity supply from tenant's stand-alone switch box by licensed electrical worker including removal of cables, trunkings/conduits/ trays and make good disturbed areas to match existing (Rate include submission of application to PowerGrid/Relevant Authorities and exclude removal of exposed cables, trunkings/trays etc) CONCRETE REPAIR Repair spalling concrete by patch with approved polymer modified sand-cement mortar as specified in Annex C-1 Repair spalling concrete by patch repair with approved epoxy mortar as specified in Annex C-1. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A492
line
35.70
A493
Point
13.80
A494
job
32.20
A495
job
8.10
A496
job
101.00
A497
m2
57.80
A498
m2
188.90
PAGE 49 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CONCRETE REPAIR (CONT'D) Repair spalling concrete by pressure grouting with non-shrink grout or other approved materials as specified Annex D-1. Repair cracks by epoxy injection as specified in Annex B-1. Patch repair cracks on walls/floors with non shrink grout 'Cem-Grout' or other approved equivalent including removal of loose materials, dirt and foreign matters. Hack 13mm "V" groove along crack, apply primer and patching with epoxy mortar as specified in Annex A-1. Hack 13mm "V" groove along crack and patch with acrylic compound or other approved flexible compound. Procedure as specified. Hack 20mm "V" groove along crack and patch with 1:3 cement and sand mortar. Patch cracks on walls/floors average not exceeding 25mm width with 1:3 cement and sand mortar including preparing cracks to receive mortar. Filling up gaps/pot holes with 1:3 cement and cement mortar including preparing gaps gaps/holes to receive mortar. Seal crack surfaces with polymer emulsion. Apply approved acrylic protective coating to building component including removal of any flaking paintwork and painting to match. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A499
m2
174.50
A500
34.20
A501
3.20
A502
7.30
A503
6.90
A504
4.30
A505
1.10
A506
m3
229.20
A507
m2
2.60
A508
m2
3.60
PAGE 50 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION CONCRETE REPAIR (CONT'D) To erect timber shoring frames to columns and walls (including lateral bracings, base anchorings bolts) to HDB's approval. (Design & submission of drawings by Contractor's PE shall be paid separately if any) Supply labour, props and I-beam (X-sectional 150 x 100) including related accessories to prop up damaged beam including taking down. Supply, erect and dismantle approved steel props excluding timber support (per day) WATER SEEPAGE/LEAKAGE Expose the concrete surface, grind, dampen and apply crystalline waterproofing compound as specified in Annex H-1. Repair of water seepage through porous concrete by injecting approved water, reactive polyurethane based chemical grout as specified in Annex F-1. * Application of liquid-applied elastomeric waterproofing membrane inclusive of preparing the surfaces according to manufacturer's instructions *(A514 A515) Reinforced Concrete surface as specified in Clause 25.9 Technical Specification Hollow/Solid block wall as specified in Clause 25.8 Technical Specification (Water test measured separately) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A509
m3
152.80
A510
job
88.20
A511
no
0.20
A512
m2
25.10
A513
47.80
A514
m2
13.40
A515
m2
19.70
PAGE 51 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION WATER SEEPAGE/LEAKAGE (CONT'D) Repair to water leakage through floor slab around sanitary piping/floor trap /fitting with water plug, bonding agent and make good the repaired area with waterproofed mortar and floor tiles to match with the existing floor tiles and bedding around pipe and as specified in Annex G-1. Repair to internal plaster/skim coat finished wall panel as specified in Clause 49.39 Technical Specification (Vacuum blasting machine used measured separately) Apply silicone sealer to cracked joints between wooden frames and block/brick wall etc including brushing clean (for cracks not more than 5mm wide). Transportation (to/fro) and setting up/ dismantling of air compressor and vacuum blast machine. Rental of vacuum blast machine of fully pneumatic size up to 2.5 m3/minute with blastmedia capacity 20 litres including compressor. Labour for vacuum blasting the wall including preparation of wall surfaces to receive new surfaces as specified. WATER/BUILDING COMPONENT TEST Conduct water test to the repaired areas by flooding of water with minimum depth of 25mm for 4 hour including construction of temporary water barrier approved by S.O. Representative and removal upon completion. (Rate inclusive of water fee) Watertightness test to external wall by spraying water at 300 litres/hour as specified. (Rate inclusive of water fee) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A516
pt
38.10
A517
m2
19.70
A518
1.60
A519
job
62.70
A520
hr
15.00
A521
m2
1.40
A522
m2
1.00
A523
hr
11.90
PAGE 52 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION WATER/BUILDING COMPONENT TEST (CONT'D) Watertightness test to external wall by spraying water from a water hose with nozzle as specified. (Rate inclusive of water fees). Coring of concrete sample not exceeding 250mm diameter including transporting the sample to the laboratory as directed and reinstatement of core-hole to match existing upon completion of the test (testing fee to be paid separately). Rebound hammer test (12 readings per point) including exposing concrete surfaces, grinding and reinstatement works to match existing. Carbonation test ( 3 readings per point) including drilling of 10mm diameter hole into concrete spraying with indicator and reinstatement works to match existing upon completion of the test. Carbonation test to core sample by spraying phenolphthalein indicator. Extra over item A525 to A528 for mobilisation of equipment to carry out test on site. MISCELLANEOUS Supply and delivery to site incense paper burner fabricated from 44 gallon drum complete with hinged door, 2nos. 9mm dia. mild steel handles, 25mm dia. perforated holes at not more than 100mm c/c in 3 rows with 2210 galvanised mesh base netting supported by 4 legged stand and finished with 2 coats of red lead primer. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A524
hr
11.90
A525
core
118.50
A526
test
40.30
A527
test
28.80
A528
test
11.50
A529
job
120.80
A530
no
53.40
PAGE 53 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION MISCELLANEOUS (CONT'D) * Labour and plant to cart away and dispose rubbish, furniture etc left behind by terminated tenant at approved dumping ground. Contractor shall required to submit original copy of the dumping receipt for weight above 0.5 ton *(A531 A537) Not exceeding 0.5 ton Exceeding 0.5 ton and not exceeding 1.5 ton Exceeding 1.5 ton and not exceeding 2.5 ton Exceeding 2.5 ton and not exceeding 3.5 ton Exceeding 3.5 ton and not exceeding 4.5 ton Exceeding 4.5 ton and not exceeding 5.5 ton Total weightage exceeding 5.5 ton | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
A531 A532
job job
61.20 261.00
A533
job
407.10
A534
job
472.60
A535
job
584.20
A536
job
695.70
A537
ton
128.80
A538
Wash oil stained floor/wall with 'Klenco Easy Clean' or other approved equivalent Remove existing vinyl/laminate floor tiles/sheets/carpets including all adhesive stain if any.
m2
0.40
A539
m2
1.40
PAGE 54 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY 400mm wide x 100mm thick concrete grade 20 bed under 100mm diameter drain pipes including haunching up sides of pipes to not less than half diameter of the pipes in similar concrete and necessary formwork. ( Drain pipes measured separately). Extra over item (B001) for concrete grade 20 surround minimum 150mm thick. 450mm wide x 100mm thick concrete grade 20 bed under 150mm diameter drain pipes including haunching up sides of pipes to not less than half diameter of the pipes in similar concrete and necessary formwork. (Drain pipes measured separately). Extra over item (B003) for concrete grade 20 surround minimum 150mm thick. * Ductile iron cement lined (BS 4772) heavy duty water pipes including necessary accessories and flexible joints all in replacement laid in trench (Trench and concrete bed measured separately) *(B005 B006) 80mm diameter 100mm diameter * Heavy grade coated cast iron drain pipe including necessary accessories and flexible joints all in replacement laid in trench. (Trench and concrete bed measured separately) *(B007 B010) 100mm diameter Extra over item (B007) for duck-foot bend. 150mm diameter Extra over item (B009) for duck-foot bend. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B001
12.50
B002
8.70
B003
13.50
B004
14.50
B005 B006
m m
36.20 44.40
B007 B008
m no
32.80 45.00
B009 B010
m no
49.00 77.00
PAGE 55 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter cast iron heavy duty union socket for underground pipe. 100mm diameter cast iron heavy duty duck foot bend including breaking up concrete floor, excavation, and make good work disturbed. * Salt-glazed stoneware drain pipe in flexible joint including laying on concrete bed in trench in replacement (Trench and concrete bed measured separately) *(B013 B016) 100mm diameter Extra over item (B013) for bend 150mm diameter Extra over item (B015) for bends 225mm x 450mm cast iron purpose made street gulley with 100mm outlet, including connection, all necessary excavation and concrete surround (in replacement). Concrete Grade 20 in bottom of inspection chamber including necessary formworks and B7 fabric reinforcement 225mm thick (average) concrete grade 20 benching and haunching to bottom of manholes finished with 13mm thick cement mortar (1:1) rendering, the whole finished off at a gradient of about one in six trowelled smooth with coves to 25mm radius at walls and rounded edges next channels including working carefully to edge of channels. (Channels measured separately) 150mm thick concrete grade 20 top slab including formwork, B7 fabric reinforcement and forming opening for frames. (No deduction for opening) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B011
no
44.80
B012
no
52.40
m no m no no
B018
m3
277.80
B019
m2
256.10
B020
m2
61.40
PAGE 56 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter half round salt-glazed stoneware straight or curve branch channels including bedding and jointing in cement mortar (1:1). 150mm diameter half round salt-glazed stoneware straight or curve main channel including bedding and jointing in cement mortar (1:1). 100 - 150mm diameter half round salt-glazed stoneware taper piece including bedding and jointing in cement mortar (1:1) 225mm thick brick works in manhole in cement mortar (1:3). 13mm thick cement and sand (1:3) rendering to internal surfaces of manhole. Supply and apply Granolithic concrete (1:1:1) to bottom slab in inspection chamber 32kg light duty cast iron inspection chamber cover and frame including setting frame in cement mortar and sealing cover in grease and fine sand. 32kg light duty cast iron inspection chamber cover and frame in replacement including cutting and removing old frame and making good in cement mortar. 52kg heavy duty cast iron inspection chamber cover in replacement (excluding frame). 790(L)x260(B)x 70(H)mm G30 reinforced concrete cover with 2 Nos galvanised R10 rings for grease interceptor. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B021
8.60
B022
11.40
B023
no
14.50
B024
m2
52.30
B025
m2
5.10
B026
m3
169.20
B027
no
51.50
B028
no
63.40
B029
no
58.70
B030
no
70.00
PAGE 57 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 2100mm diameter aluminium chequered plate covers including frame according to drawing. Raising or lowering of inspection chamber or sump cover and frame to match new levels using back existing cover and frame including making good all disturbed area. 600 x 450mm recessed type cast iron inspection chamber cover and frame in replacement including removing old frame and making good work disturbed. Supply, deliver and install 700mm diameter Steel Silt Trap Drum of one metre in depth. Supply and place grease trap interceptor in inspection chamber 150mm diameter salt-glazed stoneware gulley complete with grating, 100mm diameter outgo and concrete surround of minimum 100mm thick including hacking existing damaged gulley and jointing to existing pipes. Cast iron deep seal floor trap complete with hinged grating, cast iron hopper, and with vertical side or back inlets and 75mm diameter outgo pipe including hacking damaged trap and jointing to existing pipe. 150mm diameter cast iron hopper connecting piece not exceeding 300mm long including hacking existing hopper and all necessary jointing. 100mm diameter cast iron floor trap or floor waste with hinged grating, hopper and 75mm outgo and concrete surround (at ground floor slab) including hacking to remove existing damaged trap/waste and jointing to pipe. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B031
no
821.10
B032
no
22.00
B033
no
45.30
B034
no
338.10
B035
no
529.10
B036
no
49.20
B037
no
47.80
B038
no
29.10
B039
no
49.20
PAGE 58 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 150mm diameter cast iron floor trap with hinged grating, hopper and 100mm diameter outgo and concrete surround (at ground floor slab) including hacking to remove existing damaged trap and jointing to pipe. 100mm diameter cast iron 'S' trap (above ground level) 150 x 150mm perforated/non-perforated galvanised steel hinged grating. 100mm diameter copper grating with chrome finished and slit openings laid on cement mortar including necessary hacking. 150 x 150mm non-perforated plastic gully gratings. Nylon mosquito netting to grating of gully trap. Stainless steel mosquito netting at sump pump * Plastic gratings including embedding in Cement mortar *(B047 B050) 50mm diameter 75mm diameter 100mm diameter 150mm diameter 150mm diameter plastic hinged grating for floor trap including setting in concrete/cement mortar (1:3) 150mm plastic hinged grating with 100mm diameter collar including embedding in cement mortar (1:3) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B040
no
57.80
B041
no
49.20
B042
no
12.90
B043
no
8.10
B044
no
5.10
B045
no
1.50
B046
m2
30.20
B052
no.
4.40
PAGE 59 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Galvanised steel spherical dome-shaped grating 2.5mm thick to rain water down pipe including hacking and setting with cement mortar *(B053 B054) 75mm diameter 100mm diameter 100mm diameter vertical cast iron grating with 115mm outgo for rain water down pipe including hacking and setting in cement mortar 150mm diameter cast iron dome grating including embedding in cement mortar 100mm diameter ductile iron "Y" junction including flanges and fixing accessories 80mm diameter cast iron "Y" strainer ("Venn KY 6" or other approved equivalent) complete with fixing accessories Steel bolt for cast iron inspection eye covers Mild steel hanging brackets to pipes including making good all work disturbed. * Cast iron brackets to pipes including making good all work disturbed. *(B061 B062) Not exceeding 100mm diameter Exceeding 100mm diameter * Cast iron cleaning eye cover including all necessary bolts etc to pipes, bends, etc *(B063 B066) 50mm diameter 75mm diameter | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B056
no.
10.90
B057
no.
116.40
B058
no
268.70
B059
no
1.10
B060
no
4.60
B061 B062
no. no.
4.80 6.60
B063 B064
no. no.
3.50 3.70
PAGE 60 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter 150mm diameter Sealing up sand holes in cast iron pipes with metallic epoxy resin as per manufacturer's instruction * UPVC(AE) pipes for rainwater, vent, waste and soil pipes including provision of new shackle clips/mild steel brackets where necessary and hacking of holes through walls or slabs and make good all work disturbed on completion. (Fittings measured separately). *(B068 B073) 32mm diameter 40mm diameter 50mm diameter 80mm diameter 100mm diameter 150mm diameter 250mm dia UPVC rainwater downpipe including sockets and fixing accessories in trench(Concrete bed and haunching and elbows and 'T' junctions measured separately) * UPVC (AE) SS 272 fittings including all jointing and fixing accessories *(B075 B118) 32mm diameter sweep junction plain 40mm diameter sweep junction plain 50mm diameter sweep junction plain 80mm diameter sweep junction plain 100mm diameter sweep junction plain | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m m m m m m m
PAGE 61 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 150mm diameter sweep junction plain 200 x 200 x 200mm diameter 'T' junction 200 x 150 x 200mm diameter 'T' junction 80 to 50mm diameter single reducing junction 100 to 50mm diameter single reducing junction 100 to 80mm diameter single reducing junction 150 to 100mm diameter single reducing junction 200 to 150mm diameter single reducing junction 100 to 50mm diameter boss connector 100 to 80mm diameter boss connector 80mm diameter socket (Screw-on type) 100mm diameter socket (Screw-on type) 150mm diameter socket (Screw-on type) 32mm diameter plain coupling 40mm diameter plain coupling 50mm diameter plain coupling 80mm diameter plain coupling 100mm diameter plain coupling 150mm diameter plain coupling 32mm diameter Bend (any Angles)/Elbow plain with inspection opening | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B080 B081
no. no.
20.70 66.00
B082
no.
45.50
B083
no.
5.70
B084
no.
6.00
B085
no.
5.30
B086
no.
6.50
B087
no.
31.00
B088 B089 B090 B091 B092 B093 B094 B095 B096 B097 B098 B099
no. no. no. no. no. no. no. no. no. no. no. no.
4.60 4.60 4.10 5.20 6.30 2.50 2.60 2.70 3.90 4.80 7.30 2.40
PAGE 62 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 40mm diameter Bend (any Angles)/Elbow plain with inspection opening 50mm diameter Bend (any Angles)/Elbow plain with inspection opening 80mm diameter Bend (any Angles)/Elbow plain with inspection opening 100mm diameter Bend (any Angles)/Elbow plain with inspection opening 150mm diameter Bend (any Angles)/Elbow plain with inspection opening 150 to 100mm diameter level invert reducers 100 to 80mm diameter level invert reducers 100 to 50mm diameter level invert reducers 100 to 80mm diameter reducing elbow with inspection opening 100 x 100 x 80mm diameter tee 150 x 150 x 100mm diameter tee 100mm diameter tee 100mm diameter cross tee 80mm diameter female/female adaptor 100mm diameter female/female adaptor 150mm diameter female/female adaptor 80mm diameter female/female spigot adaptor 100mm diameter female/female spigot adaptor 150mm diameter female/female spigot adaptor | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B100
no.
2.50
B101
no.
2.50
B102
no.
4.50
B103
no.
4.40
B104
no.
12.30
B105
no.
12.50
B106
no.
9.90
B107
no.
7.80
B108
no.
10.10
B109 B110 B111 B112 B113 B114 B115 B116 B117 B118
no. no. no. no. no. no. no. no. no. no.
7.80 10.80 6.40 12.20 10.10 10.70 16.50 8.70 13.00 21.60
PAGE 63 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Straight connector (SS213) with rubber ring including application of approved silicone bonding agent to joints: *(B119 B125) 50mm diameter (100mm length) 80mm diameter (100mm length) 100mm diameter (100mm length) 125mm diameter (100mm length) 150mm diameter (100mm length) 80mm diameter (>100mm length) 100mm diameter (>100mm length) * UPVC (AE) fittings including all jointing and fixing accessories *(B126 B144) 32mm diameter 'S' trap 32mm diameter 'P' trap 40mm diameter 'S' trap 40mm diameter 'P' trap 100mm diameter floor/gulley trap 100mm diameter 'S' Trap (floor waste trap including hopper and grating) 100mm diameter down spout 150mm diameter down spout 200mm diameter down spout 100mm diameter UPVC Pan collar 50mm diameter service yard outlet 150 x 150 UPVC floor trap grating | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no no no no no
no no no no no no
PAGE 64 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Plastic downspout outlet fixed to 80mm diameter UPVC pipe in replacement 80mm diameter testing openings (F & F) 100mm diameter testing openings (F & F) 150mm diameter testing openings (F & F) 80mm diameter cleaning eye cover 100mm diameter cleaning eye cover 150mm diameter cleaning eye cover * UPVC (AW) water supply pipes including provision of new shackle clip/mild steel brackets where necessary and hacking of the hole through wall or slabs and making good all work disturbed on completion (Fittings measured separately) *(B145 B156) 15mm diameter 20mm diameter 25mm diameter 28mm diameter 32mm diameter 40mm diameter 50mm diameter 65mm diameter 75mm diameter 100mm diameter 150mm diameter 150mm diameter Half Round Pipe | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B138
no.
13.50
B145 B146 B147 B148 B149 B150 B151 B152 B153 B154 B155 B156
m m m m m m m m m m m m
3.80 4.00 4.50 4.60 4.80 6.10 8.70 10.30 13.10 17.30 26.60 11.30
PAGE 65 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * UPVC (AW) fittings including jointing and make good all work disturbed on completion *(B157 B232) 15mm diameter Tee 20mm diameter Tee 25mm diameter Tee 32mm diameter Tee 40mm diameter Tee 50mm diameter Tee 80mm diameter Tee 20 x 15 x 20mm diameter Reducing Tee 25 x 15 x 25mm diameter Reducing Tee 40 x 15 x 40mm diameter Reducing Tee 40 x 25 x 40mm diameter Reducing Tee 50 x 40 x 50mm diameter Reducing Tee 65 x 20 x 65mm diameter Reducing Tee 75 x 50 x 75mm diameter Reducing Tee 15mm diameter Connector or Socket 20mm diameter Connector or Socket 25mm diameter Connector or Socket 32mm diameter Connector or Socket 40mm diameter Connector or Socket 50mm diameter Connector or Socket 65mm diameter Connector or Socket 80mm diameter Connector or Socket | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B157 B158 B159 B160 B161 B162 B163 B164 B165 B166 B167 B168 B169 B170 B171 B172 B173 B174 B175 B176 B177 B178
no no no no no no no no no no no no no no no no no no no no no no
2.50 2.60 2.90 3.40 3.60 5.30 9.00 2.60 2.70 3.70 3.70 4.90 8.50 10.10 2.30 2.40 2.60 3.10 3.10 3.50 5.00 6.50
PAGE 66 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | DESCRIPTION | | SANITARY (CONT'D) | | 20mm to 15mm diameter Reducer | | 25mm to 15mm diameter Reducer | | 25mm to 20mm diameter Reducer | | 32mm to 25mm diameter Reducer | | 40mm to 32mm diameter Reducer | | 50mm to 25mm diameter Reducer | | 50mm to 40mm diameter Reducer | | 80mm to 50mm diameter Reducer | | 15mm diameter Bend (any Angles)/Elbow | | 20mm diameter Bend (any Angles)/Elbow | | 25mm diameter Bend (any Angles)/Elbow | | 32mm diameter Bend (any Angles)/Elbow | | 40mm diameter Bend (any Angles)/Elbow | | 50mm diameter Bend (any Angles)/Elbow | | 80mm diameter Bend (any Angles)/Elbow | | 20mm - 15mm diameter Reducing Elbow | | 25mm - 15mm diameter reducing Elbow | | 15mm diameter Valve Socket | | 20mm diameter Valve Socket | | 25mm diameter Valve Socket | | 32mm diameter Valve Socket | | 40mm diameter Valve Socket | | 50mm diameter Valve Socket | | 65mm diameter Valve Socket | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B179 B180 B181 B182 B183 B184 B185 B186 B187 B188 B189 B190 B191 B192 B193 B194 B195 B196 B197 B198 B199 B200 B201 B202
no no no no no no no no no no no no no no no no no no no no no no no no
2.60 2.60 2.70 3.40 3.70 4.60 3.70 6.00 2.30 2.40 2.70 2.90 3.20 3.90 7.20 2.40 2.60 2.30 2.40 2.60 2.90 3.00 3.80 4.10
PAGE 67 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | DESCRIPTION | | SANITARY (CONT'D) | | 80mm diameter Valve Socket | | 15mm diameter Faucet Socket | | 20mm diameter Faucet Socket | | 25mm diameter Faucet Socket | | 32mm diameter Faucet Socket | | 40mm diameter Faucet Socket | | 50mm diameter Faucet Socket | | 15mm diameter Faucet Elbow | | 15mm diameter Faucet Elbow with | wall-plate | | 20mm diameter Faucet Elbow | | 25mm diameter Faucet Elbow | | 40mm diameter Faucet Elbow | | 15mm diameter End Cap | | 20mm diameter End Cap | | 25mm diameter End Cap | | 32mm diameter End Cap | | 40mm diameter End Cap | | 50mm diameter End Cap | | 65mm diameter End Cap | | 80mm diameter End Cap | | 100mm diameter end cap | | 15mm diameter Single Joint | | 20mm diameter Single Joint | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no no no no no no no
B212 B213 B214 B215 B216 B217 B218 B219 B220 B221 B222 B223 B224 B225
no no no no no no no no no no no no no no
3.00 3.90 6.90 2.30 2.40 2.50 2.50 2.90 3.80 3.90 4.90 7.30 2.40 2.40
PAGE 68 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 25mm diameter Single Joint 32mm diameter Single Joint 40mm diameter Single Joint 50mm diameter Single Joint 65mm diameter Single Joint 80mm diameter Single Joint 100mm diameter Single Joint 16mm diameter PVC Shackle Clip 22mm diameter PVC Shackle Clip 28mm diameter PVC Shackle Clip 35mm diameter GS Shackle Clip 42mm diameter GS Shackle Clip 54mm diameter GS Shackle Clip Repair to leaking joints of UPVC pipe not exceeding 75mm diameter Repair to leaking joints of UPVC pipe exceeding 75mm diameter and not exceeding 150mm diameter | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B226 B227 B228 B229 B230 B231 B232 B233 B234 B235 B236 B237 B238 B239
no no no no no no no no no no no no no job
2.50 5.30 5.60 8.50 8.50 16.10 23.00 1.20 1.20 1.20 1.80 1.80 1.80 21.50
B240
job
24.70
PAGE 69 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * UPVC lined galvanised steel water pipe including accessories, fittings, re-threading joints, shackes, clips, holderbats and cutting holes through walls *(B241 B249) 13mm diameter 20mm diameter 25mm diameter 32mm diameter 40mm diameter 50mm diameter 65mm diameter 75mm diameter 100mm diameter * Galvanised steel holderbats, clips or shackle for GS water pipes including making good all work disturbed *(B250 B252) Not exceeding 25mm diameter Exceeding 25mm diameter but not exceeding 50mm diameter. Exceeding 50mm diameter Mild steel compression bracket comprising of two rings size 40mm wide, 5mm thick and 100mm diameter and two 10mm diameter threaded rods not exceeding 300mm long including painting. 13mm diameter coupling washer 20mm diameter coupling washer | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
m m m m m m m m m
B250 B251
no no
1.50 2.40
B252 B253
no no
4.10 19.80
B254 B255
no no
1.10 1.10
PAGE 70 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 30mm diameter coupling washer 40mm diameter coupling washer 50mm diameter coupling washer 75mm diameter coupling washer 100mm diameter coupling washer Galvanised flanged plate to 100mm diameter galvanised steel pipe. (gasket, bolts & nuts included). * Stainless steel pipes (BS 4127) including holderbats or clips and cutting of old pipes and making good on completion. (Fittings measured separately *(B262 B267) 15mm diameter 22mm diameter 28mm diameter 35mm diameter 42mm diameter 54mm diameter 150mm diameter stainless steel waterpipe including holderbats or clips and cutting of old pipes (fittings measured separately) and making good on completion. Repair to leaking joints of stainless steel/copper pipes including fixing accessories (regardless of diameter) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no no no no
m m m m m m m
B269
job
9.40
PAGE 71 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Copper pipes including holderbats, clips, fixing accessories and making good disturbed area *(B270 B274) 15mm diameter (Fittings measured separately) 22mm diameter (Fittings measured separately) 28mm diameter (Fittings measured separately) 54mm diameter (Inclusive of fittings) 100mm diameter (Inclusive of fittings) 15mm diameter copper piping 300mm long with connectors at both ends for fittings * Brass fittings for copper/stainless steel pipes *(B276 B340) 15mm diameter Elbows 22mm diameter Elbows 28mm diameter Elbows 35mm diameter Elbows 42mm diameter Elbows 54mm diameter Elbows 15mm diameter Faucet Elbow fixed to wall for installation of tap 15mm diameter Coupling/Union 15mm diameter CFI coupling/Union 22mm diameter Coupling/Union 22mm diameter CFI coupling/Union | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B270
8.00
B271
11.50
B272
14.80
m m no
no no no no no no no
no no no no
PAGE 72 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | DESCRIPTION | | SANITARY (CONT'D) | | 28mm diameter Coupling/Union | | 35mm diameter Coupling/Union | | 42mm diameter Coupling/Union | | 54mm diameter Coupling/Union | | 15 x 22mm diameter CMI Coupling/Union | | 28mm x 22mm diameter coupling | | 42mm x 35mm diameter coupling | | 42 x 28mm diameter coupling/union | | 35 x 54mm diameter Union | | 42 x 54mm diameter Union | | 15 x 15 x 15mm diameter Tee | | 15 x 22 x 15mm diameter Tee | | 22 x 15 x 22mm diameter Tee | | 22 x 22 x 15mm diameter Tee | | 22 x 22 x 22mm diameter Tee | | 28 x 15 x 28mm diameter Tee | | 28 x 22 x 28mm diameter Tee | | 28 x 28 x 15mm diameter Tee | | 28 x 28 x 22mm diameter Tee | | 28 x 28 x 28mm diameter Tee | | 28 x 35 x 28mm diameter Tee | | 35 x 15 x 35mm diameter Tee | | 35 x 35 x 15mm diameter Tee | | 35 x 35 x 22mm diameter Tee | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B287 B288 B289 B290 B291 B292 B293 B294 B295 B296 B297 B298 B299 B300 B301 B302 B303 B304 B305 B306 B307 B308 B309 B310
no no no no no no no no no no no no no no no no no no no no no no no no
6.00 8.70 10.30 14.10 4.50 6.30 12.90 12.90 17.50 17.50 4.90 5.90 5.90 5.90 6.00 8.10 8.10 8.10 8.10 7.90 18.10 14.20 13.30 13.30
PAGE 73 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | DESCRIPTION | | SANITARY (CONT'D) | | 35 x 35 x 28mm diameter Tee | | 42 x 22 x 42mm diameter Tee | | 42 x 28 x 42mm diameter Tee | | 42 x 42 x 15mm diameter Tee | | 42mm x 42mm x 22mm tee | | 42mm x 42mm x 28mm tee | | 42mm x 42mm x 35mm tee | | 42 x 42 x 42mm diameter Tee | | 54 x 28 x 54mm diameter Tee | | 54 x 35 x 54mm diameter Tee | | 54 x 42 x 54mm diameter Tee | | 54mm x 54mm x 22mm tee | | 54mm x 54mm x 28mm tee | | 54 x 54 x 54mm diameter Tee | | 22 to 15mm diameter Reducing Elbow | | 28 to 15mm diameter Reducing Elbow | | 28 to 22mm diameter Reducing Elbow | | 35 to 15mm diameter Reducing Elbow | | 35 to 22mm diameter Reducing Elbow | | 35 to 28mm diameter Reducing Elbow | | 42 to 28mm diameter Reducing Elbow | | 42 to 35mm diameter Reducing Elbow | | 54 to 15mm diameter Reducing Elbow | | 54 to 28mm diameter Reducing Elbow | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B311 B312 B313 B314 B315 B316 B317 B318 B319 B320 B321 B322 B323 B324 B325 B326 B327 B328 B329 B330 B331 B332 B333 B334
no no no no no no no no no no no no no no no no no no no no no no no no
13.30 19.90 19.90 19.20 19.20 19.20 19.20 18.80 29.80 29.80 31.90 28.40 28.40 28.40 5.20 6.50 6.50 11.40 11.40 11.40 17.50 18.00 25.60 25.60
PAGE 74 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 54 to 35mm diameter Reducing Elbow 54 to 42mm diameter Reducing Elbow 42mm diameter brass stop end 54mm diameter brass stop end 13mm diameter brass nipple 54mm diameter brass nipple * Ductile iron cement lined water pipes BS 4772:1988 with spigot and socket joints/flanged joints and all necessary fixing accessories and brackets/supports including hacking holes through floors, walls, or roofs and make good disturbed area (with supports where necessary) *(B341 B377) 80mm diameter water pipes 80mm diameter bend 80mm diameter tee 80mm diameter collar 80 to 40mm diameter reducer 80 to 50mm diameter reducer 80mm diameter socket and flanged connector 80mm diameter blank flange 100mm diameter water pipe 100mm diameter tee 100mm diameter collar 100 to 80mm diameter reducer 100mm diameter "duck" foot bend | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no no no no
m no no no no no no
no m no no no no
PAGE 75 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter socket 100mm groove coupling 100mm diameter spigot 100 x 100 x 100mm diameter tee 100 x 50 x 100mm diameter tee 150 x 100x 150mm diameter tee 150 x 150 x 150mm diameter tee 100mm diameter elbow/bend 100mm x 90 degree groove bend 100mm diameter blank flange 100mm diameter lengthening piece not exceeding 300mm long 100mm diameter lengthening piece exceeding 300mm but not exceeding 600mm long. 100mm diameter lengthening piece exceeding 600mm but not exceeding 900mm long. 215mm diameter flange washer for water main 100mm dia x 300mm bend 150mm diameter water pipe 150mm diameter "duck foot" bend 150mm diameter bend 150 to 100mm diameter reducer Supply, delivery and laying of 250mm diameter ductile iron pipe with cement lining. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B354 B355 B356 B357 B358 B359 B360 B361 B362 B363 B364
no no no no no no no no no no no
32.30 15.60 4.70 46.10 46.10 64.80 100.10 27.70 16.80 18.20 46.10
B365
no
64.70
B366
no
78.70
B367
no
6.90
no m no no no m
PAGE 76 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Deduct from 100mm diameter water main for without cement lining. Deduct from 150mm diameter water main for without cement lining Deduct from 100mm diameter fitting for without cement lining Deduct from 150mm diameter fitting for without cement lining * Heavy duty galvanised steel pipe to SS17 including accessories, re-threading all joints and providing additional holderbats and cutting holes through walls if necessary *(B378 B379) 80mm diameter 150mm diameter * Heavy duty galvanised steel fittings to SS17 including jointing accessories. *(B380 B386) 80mm diameter elbow 80mm x 15mm diameter tee 80mm diameter socket 150mm diameter bend/elbow 150mm diameter tee 150mm diameter collar clip 15mm diameter G.I. Plug | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B374
1.90
B375
5.60
B376
2.00
B377
5.80
B378 B379
m m
30.60 61.00
no no no no no no no
PAGE 77 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Hubless epoxy coated cast iron pipe/ fittings including all fixing clips, accessories, shackles and brackets. *(B387 B397) 100mm diameter pipe 150mm diameter pipe 100mm diameter tee 100mm diameter 'S' trap 100mm diameter - 90 degree bend 100mm diameter - 45 degree bend 100mm diameter Bend/Elbow (all angles) 100mm diameter Joint's Clip 150mm diameter Joint's Clip 100mm diameter Access Opening 150mm diameter Access Opening * Brass high pressure screw down stop-cocks/taps complying with BS75 including crutch handle and fixing accessories *(B398 B408) 13mm diameter brass bib tap with 'Allen' key handle 15mm diameter bib cock 20mm diameter bib cock 15mm diameter stop-cock 20mm diameter stop-cock 25mm diameter stop-cock 32mm diameter stop-cock | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B387 B388 B389 B390 B391 B392 B393 B394 B395 B396 B397
m m no no no no no no no no no
30.30 46.10 32.90 55.90 24.00 22.00 23.00 7.90 12.50 59.60 112.50
B398
no
15.50
no no no no no no
PAGE 78 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 40mm diameter stop-cock 50mm diameter stop-cock 13mm diameter garden bib tap with spigot nozzle 20mm diameter garden bib tap with spigot nozzle * Chromium plated high pressure brass screw down stop-cocks/taps including fixing accessories *(B409 B414) 13mm diameter bib tap with 'Allen' key handle 15mm dia bib tap "Penguin", "Mihedo MH" or approved equivalent with detached handle ('Allen' key handle) and hose union. 15mm diameter bib tap "Bibo","Enola WY/e.2" or approved equivalent with hose union 15mm diameter chrome plated bib tap with padlock locking device and water hose connector. 20mm diameter bib cock 13mm diameter stop-cock Brass hose connector to tap. 2-way outlet hydrant pillar including fixing accessories | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no
B408
no
20.10
B409
no
19.10
B410
no
15.00
B411
no
20.30
B412
no
18.70
no no no no
PAGE 79 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Fixing accessories *(B417 B424) Rubber washer for 13mm to 25mm diameter stopcock or bib cock or tap Rubber washer for 30mm to 50mm diameter stopcock or bib cock or tap Gland nut for 13mm diameter stop-cock/ bib cock Gland nut for 20mm diameter stop-cock/bib cock Gland nut for 25mm diameter stop-cock/bib cock Gland nut for 32mm diameter stop-cock/bib cock Gland nut for 40mm diameter stop-cock/bib cock Gland nut for 50mm diameter stop-cock/bib cock * Valves(brass/bronze) to BS 5154 including washers, gaskets, bolts, nuts and wheel handle (if applicable) *(B425 B453) 20mm diameter bronze gate valve 25mm diameter bronze gate valve 30mm diameter bronze gate valve 40mm diameter bronze gate valve 50mm diameter bronze gate valve 75mm diameter bronze gate valve 100mm diameter bronze gate valve 50mm diameter brass gate valve | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B417
no
1.00
B418
no
3.80
B419
no
3.40
B420
no
3.50
B421
no
3.60
B422
no
3.80
B423
no
3.80
B424
no
4.20
no no no no no no no no
PAGE 80 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 80mm diameter brass gate valve 100mm diameter brass gate valve 80mm diameter cast iron sluice valve with flanged ends and wheel head 100mm diameter cast iron sluice valve with flanged ends and wheel head 150mm diameter cast iron sluice valve with flanged ends and wheel head 25mm diameter check valve 42mm diameter brass check valve for booster pump 50mm diameter bronze spring loaded lift check valve. 50mm diameter bronze check valve 75mm diameter bronze check valve 80mm diameter bronze check valve (swing type) 40mm diameter spring-loaded brass check valve 50mm diameter spring-loaded brass check valve 80mm diameter spring-loaded brass check valve 100mm diameter spring-loaded brass check valve 40mm diameter brass ball valve 150mm diameter spring loaded brass check valve 22mm diameter mini ball valve 42mm diameter pressure release valve | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no
B436
no
211.00
B437
no
268.50
B438 B439
no no
19.10 38.20
B440
no
55.90
no no no
B444
no
38.20
B445
no
42.30
B446
no
224.80
B447
no
229.90
B448 B449
no no
44.00 317.50
B450 B451
no no
17.90 405.50
PAGE 81 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 65mm diameter brass landing valve 50mm diameter bronze drain cock 100mm diameter 'Victaulic VIC 300L' ductile iron butterfly valve with grooved ends and lever operated including fixing accessories. * Vitreous china wash hand basin complete with hanging brackets,waste discharge pipes, bottle trap and grating, vulcanite plug and chain *(B455 B458) 'PJ' vanity basin including fixing accessories 500 x 400mm (Johnson Suisse "Boston 500" or approved equivalent) 560 x 425mm (Johnson Suisse "Rosslave" or approved equivalent) 600 x 500mm (Johnson Suisse "Boston 600" or approved equivalent) 900 x 500 x 150mm deep single bowl and single drainer stainless steel basin complete with hanging brackets,waste discharge pipes, bottle trap and grating, vulcanite plug & chain * Fitting and accessories to basin and sink *(B460 B470) Cantilever bracket Brass waste complete with cobweb grating and plug with chain 32mm diameter PVC bottle trap 38mm diameter PVC bottle trap 32mm diameter UPVC waste pipe complete with necessary fittings | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
no no no
B455
no
91.50
B456
no
67.30
B457
no
70.70
B458
no
99.50
B459
no
70.30
B460 B461
no no
10.00 13.00
no no no
PAGE 82 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 13mm diameter spring loaded chromium plated self-closing tap with or without handle 15mm chromium plated brass pillar tap including all necessary accessories for fixing and jointing to pipeworks Chromium plated screw down pillar tap Chromium plated push button (spring type) pillar tap Chromium plated push button ( "Amico" delay action type) pillar tap Chromium plated sensor tap "AWS" or approved equivalent with infrared sensor action * Sanitary fittings and accessories including hacking up/removal of existing damaged fittings/accessories and make good all work disturbed *(B471 B472) 100mm diameter UPVC 'S' floor trap with hopper and vent with grating including jointing to waste pipe for upper/ground floor 100mm diameter UPVC 'P' trap complete with hopper and vent with grating including jointing to waste pipe for upper/ground floor * Flushing valve / device c/w stop valve, check valve, vacuum breaker and associated standard accessories *(B473 B495) Urinal manual operated, exposed type (Rigel FU102P or approved equivalent) Urinal manual operated, concealed type (Rigel FU-108DP or approved equivalent) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B465
no
35.60
B466
no
22.00
B467 B468
no no
22.00 69.90
B469
no
22.00
B470
no
267.50
B471
no
20.80
B472
no
19.30
B473
no
69.70
B474
no
123.80
PAGE 83 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Urinal Sensor operated, exposed type (Rigel AFS-202E or approved equivalent) Urinal sensor concealed-box type c/w cam lock flush valve for canteen "Rigel AFS-201CLT" or approved equivalent Micro switch 'Rigel' for sensor flush valve Power supply unit 'Rigel' for sensor flush valve SMT WC sensor eye 'Rigel' for sensor flush valve Elbow for 'Rigel' sensor flush valve Inlet spud 'Global GL403A' flush valve including fixing accessories Water closet manual operated exposed type (Rigel FC-102VP or approved equivalent) Water closet manual operated concealed type (Rigel FC-104DP or approved equivalent) Water closet Sensor operated, concealed type (Rigel AFS-101CLS or approved equivalent) Exposed water closet flush valve with 204 x 408mm 'L' flush pipe, vacuum breaker and stop-valve for back inlet water closet Exposed water closet flush valve with 280mm long supply pipe, vacuum breaker and stop valve for top inlet water closet bowl Exposed water closet water-saving flush valve "Rigel FC-102VP" or approved equivalent with 470 x 320mm long 'T' flush pipe, vacuum breaker and stop valve | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B475
no
325.00
B476
no
290.50
B477
no
26.00
B478
no
31.80
B479
no
112.30
B480 B481
no no
18.00 23.70
B482
no
123.80
B483
no
175.50
B484
no
348.00
B485
no
118.70
B486
no
118.70
B487
no
153.20
PAGE 84 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Exposed water closet water-saving flush valve "Rigel FC-102VP" or approved equivalent with 280mm long flush pipe, vacuum breaker and stop valve WC sensor concealed-box type flush valve with cam lock and manual over-riding for canteen "Rigel AFS 101-CLST" or other approved equivalent Concealed water closet water-saving concealed flush valve "Rigel FC-104DP" or approved equivalent with flushing pipe and 32mm diameter elbow coupling 'Rigel HYD' hydraulic actuator for flushing system. 'Rigel' elbow 6mm tub 1/8m r 6mm tub m5 thread for flushing system. 'Rigel' WC piston for version B for flushing system. Battery pack to flushing sensor (Batteries measured separately). 'Energizer No. L91' or other approved equivalent 'AA' size lithium battery for for flushing sensor. White vitreous China wall hung urinal bowl (Johnson Suisse Santana 320 or approved equivalent) White glazed urinal slabs 600mm wide x 1050mm high including making good all works disturbed White glazed urinal return end slab 1050mm high to match existing and including making good all works disturbed 75mm diameter brass cobweb grating to urinal | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B488
no
176.20
B489
no
348.00
B490
no
221.70
B491
no
53.60
B492
no
16.80
B493
no
53.60
B494
no
43.10
B495
no
4.40
B496
no
122.40
B497
no
149.40
B498
no
137.10
B499
no
15.60
PAGE 85 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) White earthenware squat w.c. pan only, complete with trap and with/without vent including making good tile surround to match if necessary and hacked up existing damage pan. Porcelain enameled foottreads for squat pan including hacking up existing and make good tile surround if necessary to match existing White earthenware pedestal w.c. pan "Saniton" or approved equivalent complete with trap with or without vent. Wall hung WC pan for Workshop "Saniton,Thunia ST2088,Daisy ST2199" or approved equivalent c/w approved fitting, seat and cover White squatting WC for canteen "Saniton, Violet ST2133" or approved equivalent Coloured squatting WC for canteen "Saniton, Violet ST2133" or approved equivalent White vitreous China pedestal w.c. suite valve type c/w flushing cistern close-coupled with pedestal water closet pan including seat, cover and approved fittings.(Rigel WC9708 or approved equivalent) 3 1/2" expansion fixing screw 'Johnson Sussie Verona' for fixing cistern to pedestal. PVC screw cap for vent of w.c. squat/ pedestal pan Plastic w.c. seat and cover (Heavy duty type) Plastic pedestal w.c. seat | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B500
no
126.20
B501
pair
22.10
B502
no
186.90
B503
no
219.90
B504
no
95.90
B505
no
118.90
B506
no
271.70
B507
no
14.40
B508
no
5.20
B509
no
26.00
B510
no
23.70
PAGE 86 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 9/4.5 litres dual action low level plastic cistern complete with plastic handle. 9/4.5 litres dual action high level plastic cistern complete with nylon cord and plastic pull Plastic cover to w.c. cistern Prepack mortar surround at base of w.c. cistern flush-pipe and squat pan joint to cure leak W.C. pedestal pan gasket PVC flush pipe not exceeding 2.0m long bent to high level cistern PVC flush pipe exceeding 2.0m but not exceeding 3.0m long bent to high level cistern 40mm diameter PVC flush pipe to low level cistern Plastic siphon unit to high/low level cistern Cistern fitting "NOVA" excluding warning pipe and inlet valve Rubber cone for joint between flush pipe and back inlet of w.c. pedestal pan Rubber washer to w.c. cistern siphon plunger including dismantling and refixing unit Galvanised siphon hook Chrome Plated lever handle to low level w.c. cistern Brass flush arm to high level cistern Plastic flush arm to w.c. cistern | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B511
no
36.10
B512
no
37.30
B513 B514
no no
23.60 4.60
B515 B516
no no
7.70 5.70
B517
no
6.70
B518
no
5.10
B519
no
42.90
B520
no
115.80
B521
no
5.90
B522
no
4.20
B523 B524
no no
4.20 8.70
B525 B526
no no
8.20 4.00
PAGE 87 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Plastic flush arm holder with nylon rope to w.c. cistern Plastic nut for flush pipe to w.c. cistern outlet connection Plastic ball-cock complete to w.c. cistern 15mm diameter ball valve in w.c. cistern 25mm diameter ball valve in w.c. cistern Surface mounted chrome-plated toilet roll holder with roller fixed to wall. Surface mounted plastic toilet roll holder with plastic roller fixed to wall. Plastic roller fixed in existing toilet roll holder brackets Stainless steel surface mounted paper holder of size : 280 x 152 x 165mm "Global, G51" or approved equivalent Stainless steel surface mounted paper holder of size : 127 x 89 x 102mm "Global, GP22A" or approved equivalent Surface mounted Stainless Steel soap dispenser approx. size 205 x 110 x 75 (Depth)mm (Rigel SD-101 or SD-102 or approved equivalent) Horizontal stainless steel liquid soap dispenser 'Duprex A600' or equivalent with push-in type valve Soap dispenser "Calfarma SDW-1000'' or approved equivalent Hand dryer "Medictinics Prima M-96A", ''Ventos'', "Rigel AHD-101" or approved equivalent | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B527
no
7.00
B528
no
4.60
B529
no
14.50
B530
no
8.80
B531
no
11.00
B532
no
21.10
B533
no
12.90
B534
no
0.90
B535
no
94.90
B536
no
33.20
B537
no
69.70
B538
no
59.40
B539
no
24.90
B540
no
193.90
PAGE 88 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Surface mounted brass chrome-finish liquid soap dispenser approx. size 190mm(L) x 82mm(W) (Rigel SD-106 or approved equivalent) Mild steel brackets for wall hung cisterns including cutting and pinning to walls 13mm diameter light gauge metal flexible inlet tube to cisterns/basins and taps complete with connectors Miniature ball valves for basin and cistern Adjustable Chrome-Plated copper shower rose including fixing accessories to wall. Rectangular lavatory mirror (Approx. size 400x350mm) including matching screws 20mm diameter stainless steel handle of length 240mm at public toilet * Water tank valves and accessories *(B548 B559) 40mm diameter high pressure equilibrium ball float valve (screw end 'Peglers' or approved equivalent) complete with copper float to water tank (DZR type) 50mm diameter high pressure equilibrium ball float valve (screw end 'EBCO Fig.1031' or approved equivalent) complete with copper float to water tank (DZR type) 75mm diameter high pressure equilibrium ball float valve (screw end 'EBCO Fig.1031' or approved equivalent) complete with copper float to water tank (DZR type) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B541
no
39.30
B542
no
5.40
B543
no
3.80
B544
no
5.00
B545
no
29.80
B546
no
16.70
B547
no
22.30
B548
no
138.90
B549
no
265.70
B550
no
676.20
PAGE 89 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter high pressure equilibrium ball float valve (screw end 'EBCO Fig.1031' or approved equivalent) complete with copper float to water tank (DZR type) 100mm diameter high pressure equilibrium ball float valve (screw end 'EBCO Fig.1031' or approved equivalent) to water tank (DZR type) Rate exclude copper float Lever stem to 40/50mm diameter equilibrium ball float valve Lever stem to 75/100mm diameter equilibrium ball float valve 300mm diameter copper ball float to water tank 400mm diameter copper ball float to water tank 75mm diameter rubber cup washer for 100mm diameter ball float valve 80mm diameter high pressure rubber expansion joint for pumpset including fixing accessories 1800mm high aluminium catladder with internal width of 350mm c/w 2 nos of 200mm centre bracket, 2 nos of rubber toes and 2 nos of floor bracket 750mm diameter aluminium framed chequered plate cover for grease interceptor for eating house/canteen Mild steel cover and frame 300 x 300mm for waste water down pipe sump. 13mm diameter bolts, nuts and washers for flange joint or other fitting. Stainless steel clamp for repair to leaking 40mm diameter pipe | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B551
no
1,038.50
B552
no
736.60
B553
no
21.80
B554
no
26.60
B555
no
220.10
B556
no
328.60
B557
no
14.00
B558
no
68.80
B559
no
114.20
B560
no
228.10
B561
no
15.50
B562
no
2.70
B563
no
8.50
PAGE 90 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Stainless steel clamp for repair to leaking 50mm diameter pipe Stainless steel clamp for repair to leaking 75mm diameter pipe 17mm wide punched steel for hanging cast iron pipe etc. (Band not exceeding 1.0 metre long) 19/25mm diameter jet spray or discharge nozzle with ON/OFF handle. Hack out existing pointing at joint between sink and wall and repoint in white cement Repair to defective ball cock of water tank including renewing washer Repair to defective w.c. cistern including renewing washer Hack hole through wall/floor/roof slabs not exceeding 150mm thick to form chase for entry of water service pipes and make good disturbed areas to match existing on completion of pipe installation Hack brick/hollow block wall and make good leak in concealed pipe joint including patching up and painting to match existing * Re-caulk and make good joints of cast iron soil or waste pipes including raking out and providing additional molten lead and spun yarn if required. *(B573 B575) 75mm diameter 100mm diameter 150mm diameter | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B564
no
12.30
B565
no
16.10
B566
no
3.00
B567
no
12.20
B568
job
3.40
B569
no
7.00
B570
no
6.50
B571
open'g
9.30
B572
joint
37.20
no no no
PAGE 91 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) * Re-caulk and make good joints of cast iron rising main including raking out and providing additional spun yarn and molten lead if required in upright position *(B576 B577) 100mm diameter 150mm diameter * Re-caulk and make good joints of cast iron rising mains on level ground including raking out and providing additional spun yarn and molten lead if required. *(B578 B579) 100mm diameter 150mm diameter * Cut cast iron rising mains and jointing with Gilbault coupling *(B580 B581) 100mm diameter 150mm diameter Repair to leaking cleaning eyes/oval shape inspection covers of cast iron soil and waste pipes of 75mm and above in diameter Clear obstructions in traps of basins or sinks and water meter pipes including cleaning up areas on completion Clear obstructions in floor traps, gulley traps and urinal trap Clear obstructions in w.c. pan Clear obstructions in soil and waste stack Clear obstructions in sullage water or rain water down pipes right through to sumps or house drains | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B576 B577
no no
5.40 6.70
B578 B579
no no
5.40 6.70
no no no
B583
job
4.00
B584
job
6.00
B585 B586
job job
17.80 17.80
B587
job
8.90
PAGE 92 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Clear obstruction in sullage water or rain water down pipe right through to sumps or house drains by high pressure water jetting equipment and electromechanical clearing equipment. * To locate and clear chokes in sewer/ grease lines and ensure smooth flow of waste water/solids including disposal of all choked waste *(B589 B592) Manual clearing by approved rods Mechanised clearing of chokes in sewer-lines by high pressure water jetting equipment < 2000psi) and/or electro-mechanical sewer clearing equipment. Lorry mounted high pressure water jetting (up to 4000 PSI) and electromachine to clear sewage pipe choke Clear obstructions in waste water interceptor trap Labour for clearing obstructions in traps of street gulleys including removal of solid waste from strainer Clearing, flushing with water, cleaning, including scraping hardened oil sludge, debris etc. off grease trap /interceptor using high pressure water jetting and electro-mechanical equipment including vacuum cleaning of solids and semi-solids and remove debris off site. Clear obstruction in grease gulley trap | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B588
job
9.70
B589 B590
job job
26.80 27.30
B591
job
223.40
B592
job
26.80
B593
job
6.00
B594
job
120.80
B595
job
6.00
PAGE 93 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Clear, flush with water, clean including scraping hardened oil sludge off sewer lines including manholes at house sewers using high pressure water jetting and/or electro-mechanical equipment including a squeegee or plug test for the sewer pipe on completion of the work and removing all debris off site. (Length of sewer line is measured through the manholes) Flush concealed apron drain lines and sumps including removing debris from site. (Rate is also applicable for sullage water lines) Service 80mm to 100mm diameter check valve Repair leakage of 80mm to 100mm diameter cast iron gate valve including renewing gaskets Refix loose sanitary accessories such as mirrors, brackets etc. Adjust stop cock to tilt towards any direction specified including making good any damaged or affected piping work Deposit sand granules (mosquito insecticide) into w.c. cistern, water seal in w.c. pans (squat / pedestal), gully traps and floor trap etc including covering with 50 micron transparent plastic sheet sealed with masking tape. (Rate inclusive of shuttering off water supply and draining off remaining water in w.c. pan and cistern if necessary) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B596
3.30
B597
2.00
B598
no
6.00
B599
no
12.70
B600
no
3.00
B601
no
3.00
B602
no
2.40
PAGE 94 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Deposit sand granules (mosquito insecticide) into w.c. cistern, water seal in w.c. pans (squat/pedestal), gully traps and floor trap etc including covering with frosted window film which should at least cover the porcelain border of the w.c. pans (squat/pedestal) (Rate inclusive of shutting off water supply and draining off remaining water in w.c. pan and cistern if necessary). * Repair leaking joints of galvanised service pipes *(B604 B608) Not exceeding 25mm diameter Exceeding 25mm diameter but not exceeding 50mm diameter Exceeding 50mm diameter but not exceeding 100mm diameter Exceeding 100mm diameter 100mm diameter full clamp to stop water leakage from burst pipe * Cowling/balloon grating and clips. *(B609 B610) 100mm diameter UPVC vent cowl to vent pipe 150mm diameter UPVC vent cowl to vent pipe * Painting to water tank *(B611 B618) Prepare, scrap, remove rust and encrustation's and other sediments from internal sides and bottom of mild steel tanks including removal of existing mosquito netting (if any), flush and clean surfaces, bracings and mop up with cloth to dry to receive new painting (painting measured separately). (Note : Only where painting is required) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B603
no
4.60
B604 B605
job job
6.30 8.40
B606
job
15.40
B607 B608
job no
23.50 102.60
B609
no
2.30
B610
no
4.70
B611
m2
0.70
PAGE 95 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Prepare and paint internal surfaces of mild/stainless steel water tanks including bracing with one coat of rust converter (Water Base). Prepare and paint internal surfaces of mild/stainless steel water tanks including bracing with two finishing coats of rust convertor (water Base). Prepare and paint internal surfaces of mild/stainless steel water tanks including bracing with two finishing coats (Epoxy Base). Prepare and paint external surfaces of mild/stainless steel water tanks with one coat of rust converter (Water Base). Prepare and paint external surfaces of mild/stainless steel water tanks with one coat of primer (Epoxy Base) Prepare and paint external surfaces of mild/stainless steel water tanks with one finishing coating (Water Base) Prepare and paint external surfaces of mild/stainless steel water tanks with one finishing coating (Epoxy Base) Patch holes in tank walls/bottoms/ covers by welding new pieces of plates (including the cost for use, transportation and removal of welding equipment) Repair leaking joints of water storage tank with non-toxic sealing compound including tightening of all bolts and nuts Repair leaking joints of FRP tank including dismantling panels, replacements of gaskets, bolts, nuts and refixing | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B612
m2
1.40
B613
m2
1.90
B614
m2
2.30
B615
m2
1.40
B616
m2
1.80
B617
m2
2.80
B618
m2
4.00
B619
no
37.80
B620
4.70
B621
panel
15.70
PAGE 96 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) 100mm diameter galvanised steel spring clip with nylon nettings cover at outlet of over flow pipe New nylon mosquito mesh to open tanks including non-toxic sealing compound, and removal of existing mesh, if any 0.65mm thick corrugated colour coated galvanised steel cover in replacement Seal up gaps along edges between covers and tanks with new nylon mosquito mesh and non-toxic sealing compound including removal of existing mesh, if any Seal up gaps along edges between covers and tanks with new nylon mosquito mesh in two layers with non-toxic sealing compound including removal of existing mesh, if any 75 x 75 x 6mm thick angle iron bracing/ stay to water tank (including bolts and nuts etc) Extra over on item (B627) for dismantling and removing of existing bracing/stay off site M12 (55mm)/M16 (40mm) stainless steel (SS316) bolts and nuts with 2 nos washer to water tank Stainless steel bolts to joints of stainless steel water tank c/o 40mm long SS316 M16 bolt, nut and 2 washers including removal of existing. Stainless steel bolts to joints of stainless steel water tank c/o 4 nos of 55mm long SS 316 M12 bolts, nuts, 8 nos washers and 1 no 225 x 220 x 5mm thick PVC foam gasket including removal of existing. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B622
no
5.30
B623
m2
1.40
B624
m2
41.40
B625
1.30
B626
1.40
B627
9.80
B628
1.30
B629
no
2.90
B630
no
9.90
B631
set
7.90
PAGE 97 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Repair leaking joints of link pipe jointing to water storage tanks including necessary gaskets, sealing compound etc Float switch to higher/lower water tank complete with bracket including dismantling and removal of existing float switch off site Inspection cover to mild steel water tank including removing old frame and making good works disturbed White glazed wall tiles including rounded edge tiles and 1:3 cement & sand mortar screed to concrete water tank in replacement Form opening through top/side/bottom of water tank for the entry of pipe not exceeding 150mm diameter including making good works disturbed, connection of pipe and drilling holes for bolts Dismantle bulging water tank panel and refix to proper shape including flushing out of water (provision of additional angle steel bracings/stays measured separately). 3660 x 1830mm (in panel form) galvanised steel water tank roof cover including one inspection opening with cover Refix fallen off water tank cover. (Provision of additional angle supports, bolts and nuts measured separately) Repair leakage at jamb nut including flushing out of water if necessary and tightening jamb nut. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B632
joint
17.00
B633
no
46.10
B634
no
36.20
B635
m2
30.90
B636
open'g
9.40
B637
panel
6.30
B638
no
1,106.50
B639
m2
6.30
B640
no
3.00
PAGE 98 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Dismantle and remove from site existing damaged inspection cover including the 150mm high four-sided galvanised steel boxing to the access hole and replace with 0.559mm thick galvanised steel cover overall size 490 x 490mm including boxing up the access hole with 150mm x 0.559mm thick galvanised steel including pop-riveting and making good. Flushing of steel strainer located after PUB Bulk Meter including dismantling and refixing Pressure gauge 0 to 60 psi and 0 to 4 kg/cm2 for booster pumping system Prepare, remove all stains and sediments from internal sides and bottom of tanks, flush and clean surfaces, including bracing to mild steel water tank. (Note: Only when painting is NOT required) Prepare, sand and remove rust, stains and other sediments from internal sides and bottom of tanks, flush and clean surfaces, including bracing to stainless steel water tank Clean and remove rust stains from External surface of stainless steel water tanks Prepare, remove all rust, stains and sediments from internal sides and bottom of tanks, flush and clean surface to FRP/GRP or R.C. Water Tanks Flush roof top water storage tanks and refill with clean water upon completion. Testing of water samples including transportation from site and submission of test reports for both bacteriological and chemical tests | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B641
cover
46.10
B642
no
8.90
B643
no
32.60
B644
m2
0.30
B645
m2
0.30
B646
m2
0.20
B647
m2
0.20
B648
job
12.10
B649
sample
72.50
PAGE 99 OF 122
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SANITARY (CONT'D) Analyses on sample of water for grease & oil Roll steel joists for support of tanks, including hoisting, fixing in position and removal of existing joists if any, and paint with 1 coat of red lead primer & 1 coat of bitumen paint Labour to carry out fortnightly or monthly inspection of either the transfer pump or booster pump installation including all necessary tools, etc. (Note: 1 pumping system consist of 2 nos. pumpsets) Labour to carry out fortnightly or monthly inspection of both the transfer pump and booster pump installation including all necessary tools, etc. (Note: 1 pumping system consists of 2 nos of pumpsets) Labour and material for sterilisation of mild steel/FRP/polyethylene lined/ stainless steel/concrete water storage or suction tank to overflow level 500 litres CIMM tank for booster pump system inclusive of dismantling & disposal of existing tank White vitreous china pedestal w.c. suit valve type c/w flushing cistern close-coupled with pedestal water closet pan and approved fitting excluding seat and cover (Claytan or approved equivalent) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
B650
sample
48.30
B651
kg
2.70
B652
system
18.10
B653
system
30.20
B654
m3
0.70
B655
no
1,177.30
B656
no
294.70
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION DAYWORK * Rates for labour and plant Exclude 15% establishment charges and profit. *(C001 C041) Labourer Concretor Pavior Plasterer Brick layer Tiler Ironmonger Steelworker Welder Roofer Joiner Carpenter Painter Glazier Plumber Licensed Plumber Electrician Wireman 2.5-3 tonne motor lorry including fuel and driver 5.5-7 tonne motor lorry including fuel and driver | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
C001 C002 C003 C004 C005 C006 C007 C008 C009 C010 C011 C012 C013 C014 C015 C016 C017 C018 C019
hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr hr
4.70 6.90 6.60 8.80 6.20 9.00 7.70 5.70 7.60 7.30 7.50 7.40 5.60 7.20 10.00 10.60 6.87 9.70 27.00
C020
hr
32.40
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION DAYWORK (CONT'D) Crane (Kato KR 20H) including fuel and driver. 80ft (approx. 24.38m) Boomlift including maintenance, diesel, operator and to/fro transportation. 100ft (approx. 30m) Boomlift including maintenance, diesel, operator and to/fro transportation. Self propelled 'scissor' lift with working platform up to maximum height of approximately 7.62m(25ft) including to/fro transportation. Air compressor with air delivery capacity not less than 4.5cu m per minute including pneumatic and sharpening tools and power supply (operator measured separately) Diesel powered field welding machine (minimum 300 Amp). Wheel or crawler shovel or excavator loader with back hoe bucket not exceeding 0.4 cu m or 1.3 cu m loader bucket capacity including fuel and driver Power loader on rubber-tyred wheels 1.20 cu m bucket capacity (Flywheel horsepower 60 KW range) including fuel and driver Traxcavator 1.0 cu m capacity including fuel and driver. Power driven pump 50mm size including fuel and driver Mobilization of truck mounted concrete pump including fuel and driver Erection of double layer metal scaffolding complying with safety regulation including taking down after (irregardless of height) (PE fees not included) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
C021
hr
106.00
C022
day
598.50
C023
day
562.30
C024
day
37.30
C025
hr
22.70
C026
hr
13.20
C027
hr
70.10
C028
hr
62.30
C029
hr
70.40
C030
hr
13.90
C031
job
577.50
C032
m2
7.30
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION DAYWORK (CONT'D) Erection of double layer metal scaffolding complying with safety regulation including taking down after (irregardless of height) (inclusive of PE fees) Mobile stagging compliance with safety regulation and taking down after use. (per job duration) Erection of single layer timber scaffolding including taking down after use Erect double layer timber scaffolding including taking down after use Submission of drawing and roof plans by Professional Engineer to the relevant Authorities for approval (building having similar roof plans/ design shall be included in this rate and shall NOT be paid separately under one operation). To carry out testing of mechanical suspended cradles by Professional engineer and obtain approval from the relevant authorities. Supply and install mechanical suspended cradles not exceeding 5m length to the roof including application/submission of electricity supply to various authorities for approval by approved licensed electrical workers (hiring charges and shifting shall be paid separately). Hiring charge of approved mechanical suspended cradle not exceeding 5m length including all accessories and safety precautions Labour for shifting approved mechanical suspended cradle within the same block. Standby Plumber | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
C033
m2
25.00
C034
job
85.10
C035
m2
3.10
C036
m2
6.30
C037
block
367.50
C038
no
210.00
C039
no
690.00
C040
day
52.30
C041
Job
40.00
C042
hr
10.00
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES Reinstatement Works Dismantling of Mezzanine floors all as specified in Clause 49.3. Dismantling of Storage Platform all as specified in Clause 49.3. Dismantling of office/storeroom all as specified in Clause 49.4 for partition walls. (Based on wall area) Dismantling of office/storeroom all as specified in Clause 49.4 for false ceiling. (Based on false ceiling area) Dismantling of fixed wall cabinets/ shelves all as specified in Clause 49.5. * Painting works to internal of units as specified in Clause 49.6.1 to the following internal floor areas: *(D006 D016) >50.00m2 but not >100.00m2. >100.00m2 but not >150.00m2. >150.00m2 but not >200.00m2. >200.00m2 but not >250.00m2. >250.00m2 but not >300.00m2. >300.00m2 but not >350.00m2. >350.00m2 but not >400.00m2. >400.00m2 but not >450.00m2. >450.00m2 but not >550.00m2. >550.00m2 but not >650.00m2. >650.00m2 but not >900.00m2. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D001
m2
11.00
D002
m2
4.20
D003
m2
1.20
D004
m2
2.20
D005
m2
7.20
D006 D007 D008 D009 D010 D011 D012 D013 D014 D015 D016
unit unit unit unit unit unit unit unit unit unit unit
506.00 649.00 770.00 836.00 902.00 968.00 1,089.00 1,595.00 1,683.00 1,793.00 1,936.00
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Reinstatement Works (Cont'd) * Painting works to Roof Purlins and Thrusts of units as specified with the following floor area of Internal unit: *(D017 D027) >50.00m2 but not >100.00m2. >100.00m2 but not >150.00m2. >150.00m2 but not >200.00m2. >200.00m2 but not >250.00m2. >250.00m2 but not >300.00m2. >300.00m2 but not >350.00m2. >350.00m2 but not >400.00m2. >400.00m2 but not >450.00m2. >450.00m2 but not >550.00m2. >550.00m2 but not >650.00m2. >650.00m2 but not >900.00m2. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D017 D018 D019 D020 D021 D022 D023 D024 D025 D026 D027
unit unit unit unit unit unit unit unit unit unit unit
231.00 319.00 407.00 506.00 572.00 627.00 682.00 759.00 880.00 990.00 1,276.00
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Reinstatement Works (Cont'd) * Removal of electrical wirings & fittings installed by tenants including termination of power supply (as specified in clause 49.9) to the following floor areas of internal unit (whole unit). *(D028 D038) >50.00m2 but not >100.00m2. >100.00m2 but not >150.00m2. >150.00m2 but not >200.00m2. >200.00m2 but not >250.00m2. >250.00m2 but not >300.00m2. >300.00m2 but not >350.00m2. >350.00m2 but not >400.00m2. >400.00m2 but not >450.00m2. >450.00m2 but not >550.00m2. >550.00m2 but not >650.00m2. >650.00m2 but not >900.00m2. Supply labour and tools to remove and dipose curtains, blinds and rails (if any) including patch up holes with approved non-shrink cement grout and painting to match existing. (regardless of height) Supply and apply one coat penetrative solvent deposited primer/sealer coating and 2 coats single pack solvent deposited liquid dressing to external wall. Supply and apply "Flexcoat" or other approved equivalent applied waterproofing membrane coating system to wall. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D028 D029 D030 D031 D032 D033 D034 D035 D036 D037 D038 D039
unit unit unit unit unit unit unit unit unit unit unit m
143.00 154.00 176.00 198.00 198.00 209.00 215.00 231.00 242.00 245.00 249.00 1.20
D040
m2
2.60
D041
m2
7.60
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and apply 2 coats "Sonvacryl" or other approved equivalent flexible acrylic waterproofing membrane. 10mm thick prepacked waterproof screed for kitchen, bath and WC floors as specified Supply and apply 30mm x 15mm deep 'StoSeal' SPS A Grey sealant or other approved equivalent. Supply and apply 30mm x 30mm deep 'StoSeal' SPS A Grey sealant or other approved equivalent. Supply and apply 40mm x 20mm deep 'StoSeal' SPS A Grey sealant or other approved equivalent. Supply and apply 110mm x 10mm deep 'StoSeal' SPS A Grey sealant or other approved equivalent. Supply and install backing rod and non-shrink grout to expansion joint. Supply and install backing rod cushioned by 20x10mm thick polyurethane sealant and non-shrink grout to expansion joint. Supply and fix N6 welded steel fabric reinforcement well lapped and tied at joints (measured nett). Supply and lay 'Quicseal 718' fibre or other approved equivalent fibre mesh. Supply and fix 25mm diameter mild steel rod hinges. Stainless steel knobset/night latch lockset "Union 9303/361" or other approved equivalent including anti-thrust latch | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D042
m2
18.70
D043
m2
5.90
D044
5.70
D045
10.70
D046
10.40
D047
12.90
D048
4.10
D049
8.50
D050
m2
11.60
D051
m2
2.60
D052
no
10.00
D053
no
25.70
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 135 x 65 x 6mm brass hasp and staple at OG Box Supply and install "J4LA600AB" or other approved equivalent lever handle entrance lockset under KA system. Supply and install bronze anodised extruded aluminium frame casement window with sheet float glass, aluminium fronting, ironmongery & cill with cement infill & all necessary fixing & jointing materials and accessories as specified with 6mm thk obscured rough cast wired glass. Supply and install natural anodized aluminium fixed louvred vent with 2.3mm thick extruded aluminium louvred blades including all necessary fixing accessories. Supply and install curved galvanised steel coils metal roof minimum 0.60mm thick coated with full strength fluoropolymer coating and complete with vinyl weatherseal as an integral part of Snap-On-Seam cover with 10 years 1.0m high stainless steel railing - 50mm dia x 2mm thick pipe as top, mid rail and balustrades at 1200mm c/c cast in concrete. Removal of damaged 450mm diameter x 0.8mm thick galvanised steel duct, supply and installation of new 450mm diameter x 0.8mm thick galvanised steel duct. Supply and installation of fluorocarbon coated aluminium 3mm thick bend sheet with perforation. Supply and install 50mm thick Promatech 'H' or other approved equivalent 2 hour fire rated weatherproofed board panel to flue duct | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D054
no
23.50
D055
set
52.70
D056
m2
199.60
D057
m2
319.90
D058
m2
84.50
D059
102.60
D060
job
446.80
D061
m2
386.40
D062
m2
307.90
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install I-bracket inclusive of 40mmx3mm anchor plate, 4" U-bolt and 3/8mm wall plug (rate exclude staging used). Supply and fix 25mm diameter galvanised steel bolt x 170mm long thread c/w 1 no. washer to stanchion plate of bollard (stanchion plate not included). Filling up gaps/pot holes with "Davco Lapgrout 60" or other approved equivalent, including preparing gaps/pot holes to receive grouting. Supply and apply 'Dinos' or other approved equivalent remover & tile cleaner acid to clean oily floor surface. Supply and install foot-operated grade 304 SS refuse chute hopper to centralised refuse chute complete with all necessary fixing accessories including dismantling existing (Overall size:1100 x 700 x 1.5mm thick). Supply and install 3000mm x 600mm x 2mm thick aluminium panel including 1 primer coat and 2 finishing coats of approved paint. 2100mm diameter aluminium chequered plate covers including frame according to drawing. Supply and install 150mm diameter class 'C' galvanised steel tee Supply and install 100mm diameter class C heavy duty bolted gland ductile iron underground gas pipe. Supply and install vulcanite plug complete with chain to fireclay sink/wash hand basin/ stainless steel sink. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D063
no
29.20
D064
no
60.10
D065
m3
1,568.50
D066
m2
0.70
D067
no
917.40
D068
no
120.80
D069
no
821.10
D070
no
124.00
D071
297.10
D072
no
4.50
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and fix 100mm ductile iron strainer. Supply and fix 100mm rubber washer for leaking ball float valve. Basin mounted soap dispenser "GAMCO G29L" or other approved equivalent. Supply and fix (in replacement) 15mm diameter bottom-inlet ball valve comprise with ball valve for siphon unit for low capacity (water saving) cistern. Supply and install 100mm diameter class C heavy duty bolted gland ductile iron underground gas pipe. Supply and install 100mm diameter class C heavy duty bolted gland ductile iron bend Supply and install friction stay not exceeding 300mm long including all fixing accessories. Supply and install friction stay exceeding 300mm long including all fixing accessories. Replacement of damaged rivet with approved stainless steel rivets. Supply and install new manuallyoperated roller shutter door, "Gliderol" or other approved equivalent, in 0.5mm thick Lysaght's Colorbond finish, complete with all necessary proprietary fittings to suit opening size and excludes operator (removal of existing shall be paid separately) (area measured nett opening) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D073
no
348.50
D074
no
16.60
D075
no
60.20
D076
no
20.00
D078
297.10
D079
no
217.40
D080
no
10.40
D081
no
16.40
D082
no
0.70
D083
m2
120.80
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Extra over to Item D083 for supply and install motor operator (electronic type) with control panel for electrical operated "Gliderol" or other approved equivalent roller shutter door. Extra over to Item D083 for supply and install planetary gearing (complete set for manually operated "Gliderol" or other approved equivalent roller shutter door. General servicing of roller shutter including easing, adjusting, greasing and sundries, etc. Supply and install anodised extruded aluminium framed 2-track sliding window complete with 5mm thick clear sheet/float glass, ironmongery and all necessary fixing and jointing materials and accessories. Supply labour and material to oil, adjust and ease adjustable lourve windows. Supply labour and material to remove glue stain. Supply labour and material to remove bolts below concrete surfaces including patch up holes with approved non-shrink cement grout. Supply labour and material to remove signages, basins, clothes hanger, shower set, light fittings and eletrical board/box including patch up holes with approved non-shrink cement grout. Supply labour and material to remove and dispose pipes, conduits and trunkings including patch up of holes to match existing. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D084
set
1,207.50
D085
set
241.50
D086
door
241.50
D087
m2
95.90
D088
m2
0.50
D089
m2
0.70
D090
no
0.40
D091
no
1.50
D092
0.60
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 75mm brass shoot bolt. Supply and install cam lock for roller shutter panel door Waist high lock for 'Gliderol' or other approved equivalent roller shutter door. Wash stained toilet floors with approved chemical Wash stained toilet wall tiles, doors and all sanitary fittings with approved chemical Supply labours, tools and detergent to clean down provisional result unit (regardless of floor area) and inclusive of mobile stagging to the following: - Both faces of windows, vents, doors and shutters; wall/floor tiles, concrete floor and sanitary fittings Extra over for attending to emergency work instructed by HDB's EMS Contractor or SO Reps (Clause 48.6) after office hours (Mon - Fri - 6:01pm to 7:59am and Sat - after 1:00pm), Sunday and Public Holiday Supply and install copper reducer from 65mm to 50mm. 25mm thick concrete screed (Grade 25) with 10mm maximum size aggregate to concrete floor surfaces finished with steel trowelling including all necessary labour and materials for preparation of substrate's surface to receive screed as specified Add to (or deduct from) item D102 for each 5mm thickness over (or under) 25mm thick. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D093
no
1.80
D094
no
12.20
D095
no
46.60
D096
toilet
18.40
D097
toilet
18.40
D098
Day
46.30
D099
Job
15.00
D100
no
19.10
D102
m2
7.60
D103
m2
1.20
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Extra over concrete floor or screed for the application of approved non-metallic hardener with power trowelled finish including spraying a coat of approved curing agent onto the finish surface as specified. 20mm thick prepacked screed to floor trowelled to a smooth finish Add to (or deduct from) item D105 for each 5mm thickness over (or under) 20mm thick Supply and lay 108x108x 5mm thk white glazed wall tiles including cement & sand mortar (1:2:5) based screed. Supply and install custom made intermediate roller guide cum 75mm(H) x 17mm(L) x 3mm thk mild steel hinge to metal folding door Supply and install 30mm thk hollow core timber door to handicap toilet. Supply and fix casement, pivoted or top hung window rubber gasket include removal & disposal of existing ensure water tightness. Supply and apply silicone sealant to bind aluminium plate to timber door (For gap not exceeding 7.5mm3) Supply and install 850(ht) x 530 (width) x 19mm thk timber laminated cupboard door to with 2 nos of stainless steel hinges to match existing. Supply and install new cubicle door with formica finish size 600 x 1800 including labour for taking down existing cubicle door (to re-use existing ironmongery). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D104
m2
9.50
D105
m2
7.10
D106
m2
1.50
D107
m2
39.40
D108
set
22.30
D109
no
105.40
D110
2.30
D111
0.30
D112
no
96.60
D113
no
112.70
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 'Posse C111AZ-85mm' entrance knobset. Supply 38mm padlock Supply and install cam lock for staircase common power point metal housing. Supply and install buckle for securing bars. Supply and install CP sink tap. Supply and install 'Poly' Model : FV7070 flush valve, 4.5 litres syphon for flushing cistern. Supply and install 1/2" adjustable anti-siphon cistern fill valve as ball valve for flushing cistern. Supply and install "Rigel" solenoid valve for W.C. flush valve Supply and fix 25x15mm diameter brass bush for copper pipe Supply and fix 15mm diameter brass CFI socket for copper pipe Supply and fix 15mm diameter brass CMI union for copper pipe Supply and install 54mm x 54mm x 15mm tee (brass) Supply and install 50mm diameter galvanised iron pipe. Supply and install 50mm diameter galvanised iron socket Supply and install 50mm diameter galvanised iron elbow. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D114
no
70.90
D115 D116
no no
8.10 12.80
D117
no
3.60
D118 D119
no no
26.10 68.30
D120
no
42.00
D121
no
136.50
D122
no
5.80
D123
no
5.20
D124
no
4.90
D125
no
37.70
D126
13.70
D127
no
8.40
D128
no
11.60
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 50 x 25mm diameter galvanised iron tee. Supply and install 50mm diameter galvanised brackets (for pipeworks). Supply and fix 25mm diameter brass nipple for stainless steel pipe Supply and fix 25mm diameter brass socket for stainless steel pipe Supply and install 600x600x90mm thick medium duty double triangular manhole cover with frame Fill up holes on aeration slabs with granite fines to prevent stagnation of water Supply labour and materials to mobilise generator on site, dismantle existing collapsed fencing including support angle, barb wire (including erect new fencing with barb wire to match existing) Supply and install 44mm thick framed, ledged, braced and batten single leaf door comprising of 100 x 44mm styles and top rail, 150 x 25mm bottom ledge, 100 x 25mm middle ledge and braces filled in with 19mm thk tongued and grooved 'V' jointed boarding (excluding door frame, ironmongeries and painting). Supply and install 44mm thick framed, ledged, braced and batten double leaf door comprising of 100 x 44mm styles and top rails, 150 x 25mm bottom rails, 100 x 25mm intermediate rails and braces filled in with 19mm thk tongued and grooved 'V' jointed boarding (excluding door frame, ironmongeries and painting). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D129
no
13.70
D130
no
4.70
D131
no
6.40
D132
no
8.50
D133
no
117.40
D134
m2
1.70
D135
job
7,000.40
D136
m2
153.30
D137
m2
155.20
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and Install 50mm thick framed lourved double leaf door comprising of 150 x 50mm styles and top rails, 200 x 50mm bottom rails, 150 x 50mm intermediate rails and 19mm thick timber lourves fixed at not more than 19mm apart. (excluding door frame, ironmongeries and painting) Supply and lay average 10mm thick "Lanko" rapid self leveling screed with 1 coat of "Lanko" acrylic primer. Supply and replace 32kg light duty cast iron inspection chamber without frame Supply, fabricate and install 2.98m(w) x 3.15m(ht) electrical/ chain operated aluminium rolling shutter in natural anodised finish interlocking slats c/w side guides, limit switch & accessories (re-use existing roller cabinet, motor & push panel, exclude running wires from DB to panel Supply and install garden tap with locking device Supply 30mm Tri-circle padlock Supply and install 15x28mm dia brass union Supply and install ''Henderson 104/97'' roller guides for metal sliding door Supply and install lockset to toilet PVC bi-fold door 25mm thick approved polymer modified mortar to concrete floor surface finished with steel trowel Add to (or deduct from) item D147 for each 5mm thick approved polymer modified mortar over (or under) 25mm | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D138
m2
237.30
D139
m2
14.20
D140
no
43.70
D141
no
1,495.00
D142
no
14.50
no no no
D146
no
24.70
D147
m2
38.00
D148
m2
6.50
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install heavy duty 200mm dia. PVC dome grating including making good all work disturbed and fixing accessories, etc. Supply and install 200mm dia. Elbow 45 and 90 degrees Supply and install 200mm dia PVC end cap Supply labour and material to repair and replace 1/4' tube for pedestal sensor valve and including all necessary accessories Grind off floor coating, eg. Epoxy paint, residual glue, stubborn stains, etc., with 'push cart' grinding machine consisting of grinding stone Supply and replace 31''x 18'' single bowl single drainer stainless steel sink Supply white/red strip tape Supply and apply 2 coats of 2 pack polyurethane paint (non-metallic) on concrete, plastered or tile surface Supply and deliver mineral water (Package: 240ml x 48 cups) Supply and fix 6mm thick obscured wired glass louvres with polished edges to metal/timber frames Supply and install lock for tap-off box (Model: KAM Keylock 92268) Supply and lay Grade 30 (Davco grout 280) non-shrink grout topping to existing scupper drain (various in thickness) in small quantities not exceeding 0.25m3 including trowelling smooth to surfaces as instructed | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D149
no
27.50
D150
no
35.90
D151
no
42.20
D152
no
80.50
D153
day
305.90
D154
no
45.60
D155 D156
no m2
1.40 5.90
D157
box
6.90
D158
m2
NA
D159
no
15.50
D160
m3
883.80
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install size 40mm diameter backer rod (for expansion joint) Supply ''Tri-circle 265'' 50mm padlock c/w key-alike Supply and paint 2 coats of water-based algae resistant emulsion paint Supply and fix 3mm thick polished clear acrylic covers (size: 880x600mm) with 1.5mm thick L-shape anodised aluminium profiles on both vertical sides for directory board Supply and install A217 stainless steel rising hinges to toilet cubicle Supply and install custom made hanger to metal folding door Supply and install 600x600x5mm thick lavatory square mirror including fixing accessories Erecting and dismantling the existing double layer metal scaffolding for reuse Service rendered by Licensed Locksmith to unlock / pick / break locks, subject to maximium one (1) hour at site (inclusive of tools & transport) Extra over D169 to wait to unlock / pick / break locks as instructed by S.Os Representatives beyond one (1) hour. Extra over D169 to standby to unlock / pick / break locks, however jobs had been called off by S.Os Representatives. Supply labour and tools to break door/gate lock. Extra over D169 to D172 for waiting time on site exceeding one hour (1st hour not payable) Service Charge for attendance at site only (where unlock or break open locks are not required). | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D161
2.90
D162
no
11.50
D163
m2
3.60
D164
no
53.40
D165
pc
18.00
D166
no
95.00
D167
no
43.40
D168
m2
1.10
D169
job
57.50
D170
hr
12.50
D171
hr
12.50
D172
no
NA
D173
no
NA
D174
no
NA
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | DESCRIPTION | | SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) | | Supply of 60mm padlock (long shackle type) | | Supply and install natural anodised alloy | casement window fastener c/w handle, nut, | washer etc. to aluminium casement window | | Supply and fix 4.5mm thick aluminium | chequered regulating strips to concrete | pavement | | Paint 2 coats of approved solvent-based | washable paint to surfaces of walls, ceilings, | columns including preparing surfaces | without dilution | | Supply and install 150x100x150mm | diameter UPVC 'T' junction | | Supply and install 150mm diameter | UPVC bend without inspection opening | | Supply and install 25mm brass padlock | with key alike | | Supply of 50mm diameter PVC dome | outlet | | Supply of 75mm diameter PVC dome | outlet | | Supply and install window film T8175SR | to room | | *Mobilisation of equipment, personnel, etc, | to conduct cable detection cables * (D185 D187) | | Radius not exceeding 100 metres | | Radius between 101 metres to 300 metres | | Radius between 301 metres to 500 metres | | Service charge for submitting Notice of | Commencement of Earthwork (NCE) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D175 D176
no no
12.00 9.00
D177
m2
94.70
D178
m2
3.50
D179
no
25.90
D180
no
8.90
D181
no
4.40
D182
no
2.70
D183
no
5.80
D184
hr
97.80
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Carrying out of paint dilution test (1 sample per test) for either acrylic emulsion paint or water-based algae resistant emulsion paint *Stainless steel pipe for railing purposes including all necessary cutting, welding, polishing, bending to shape and fixing on site* (D190 to D193) 38.1mm diameter x 1.5mm thick 38.1mm diameter x 2.0mm thick 50.8mm diameter x 1.5mm thick 50.8mm diameter x 2.0mm thick Supply and install ductile iron gate valve to BS5163 with rubber-bonded wedge, spindles turn in closewise-to-close direction, flange drilled to BS 4504 PN 16 c/w valve body, bonnet internally and externally coated in epoxy resin Supply and install 60mm x 50mm bronze reductor coupling. Supply of 100 pcs 77/53mm cable ties Supply and install custom made electro-galvanised steel spring clamp used to hold electrode inserted on water tank cover Supply & install 6000mm X 450mm X 200mm double sided open panel illuminated CSE-803 aluminium extrusion gantry signboard for "Entrance" Size Supply and install Union CZ682-88-88CH lockset Supply and install Low Level 4.5 Litres Single Flushing Plastic Cistern with Push Button Supply and install 30mm diameter brass plated with stainless steel 'Rocket' shackle padlock to water tank covers | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D189
no
103.50
no no no no no
D195
no
196.80
D196 D197
lot no
14.00 165.00
D198
no
2,634.00
D199
no
83.80
D200
no
67.20
D201
no
18.00
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 2mm x 80mm x 80mm thick stainless steel handicapped logo signage (painted white with 3005C penton code-blue background) at lift lobbies including all neccessary fixing accessories. Engraving of ''WT'' on keys Cutting of concrete slab/ bituminous premix pavement with diamond cutter to a depth not exceeding 25mm Supply & install expansion joint U/E T/B 50mm diameter, Q-flexible Supply and install custom made galvanised track for metal folding door. Take down existing aluminium bi-folding door for industrial shops Secure and reassemble aluminium bi-folding door (including all fixing accessories) Replace top hanger track for aluminium bi-folding door (inclusive of 12months defects liability period) Replace top hanger roller for aluminium bi-folding door (inclusive of 12months defects liability period) Replace bottom track guide for aluminium bi-folding door (inclusive of 12months defects liability period) Fix back the bi-folding door & do alignment (including all fixing accessories) Supply and fix 3mm thick 600x600mm wide PVC sheet to bottom of switchboard Supply & install 0.5mm thick galvanised sheet including bending, lapping, fixing accessories and sealing of joints (Painting paid separately) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D202
no
11.50
D203 D204
no m
2.00 3.30
D205
no
68.60
D206
13.80
D207
job
80.00
D208
job
180.00
D209
20.00
D210
no
50.00
D211
no
20.00
D212
job
180.00
D213
m2
17.90
D214
m2
22.30
SCHEDULE OF RATES FOR BUILDING WORKS (2009/2011) | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | S/N | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DESCRIPTION SUPPLEMENTARY SCHEDULE OF RATES (CONT'D) Supply and install 12.5mm x 12.5mm x 20 BWG galvanised welded mesh inclusive of screws and washers Supply and fix (in replacement) handle fasteners on aluminium casement window. Supply and fix (in replacement) of 8mm dia. x 10mm long stainless steel screws to existing aluminium window friction stay. Rental of one unit 14m Diesel Boom Lift (excludes to and fro transportation charges) To and fro transportation charges of one unit 14m Diesel Boom Lift. Supply and replace fire rated board at roof top dog house c/w painting (Size 980mm x 600mm) 42mm to 15mm diameter brass reducing elbow for copper/stainless steel pipes Supply and install Grid: 50mm x 150mm hot dipped galvanised BRC fencing panel mesh (2.4m length x 1.5m height) Supply and install hot dipped galvanised BRC fencing post (50mm Dia x 2.1m Length) Supply and install NEOPERL or other approved constant flow regulator (in-line type) [2 litre / min] | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UNIT | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
RATE
D215
m2
5.90
D216
no
2.30
D217
no
0.20
D218
no
1,035.00
D219
trip
230.00
D220
no
80.00
D221
no
16.80
D222
m2
150.60
D223
no
62.80
D224
job
9.60