Professional Documents
Culture Documents
Circuit Design Suite Getting Started
Circuit Design Suite Getting Started
Support Worldwide Technical Support and Product Information ni.com National Instruments Corporate Headquarters 11500 North Mopac Expressway Austin, Texas 78759-3504 USA Tel: 512 683 0100 Worldwide Offices Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 5050 9800, Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 358 (0) 9 725 72511, France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737, Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466, New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 328 90 10, Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886, Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085, Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222, Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545 For further support information, refer to the Technical Support and Professional Services appendix. To comment on National Instruments documentation, refer to the National Instruments Web site at ni.com/info and enter the Info Code feedback. 20062010 National Instruments Corporation. All rights reserved.
Important Information
Warranty
The media on which you receive National Instruments software are warranted not to fail to execute programming instructions, due to defects in materials and workmanship, for a period of 90 days from date of shipment, as evidenced by receipts or other documentation. National Instruments will, at its option, repair or replace software media that do not execute programming instructions if National Instruments receives notice of such defects during the warranty period. National Instruments does not warrant that the operation of the software shall be uninterrupted or error free. A Return Material Authorization (RMA) number must be obtained from the factory and clearly marked on the outside of the package before any equipment will be accepted for warranty work. National Instruments will pay the shipping costs of returning to the owner parts which are covered by warranty. National Instruments believes that the information in this document is accurate. The document has been carefully reviewed for technical accuracy. In the event that technical or typographical errors exist, National Instruments reserves the right to make changes to subsequent editions of this document without prior notice to holders of this edition. The reader should consult National Instruments if errors are suspected. In no event shall National Instruments be liable for any damages arising out of or related to this document or the information contained in it. EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CUSTOMERS RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE ON THE PART OF NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including negligence. Any action against National Instruments must be brought within one year after the cause of action accrues. National Instruments shall not be liable for any delay in performance due to causes beyond its reasonable control. The warranty provided herein does not cover damages, defects, malfunctions, or service failures caused by owners failure to follow the National Instruments installation, operation, or maintenance instructions; owners modification of the product; owners abuse, misuse, or negligent acts; and power failure or surges, fire, flood, accident, actions of third parties, or other events outside reasonable control.
Copyright
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation. National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction. BSIM3 and BSIM4 are developed by the Device Research Group of the Department of Electrical Engineering and Computer Science, University of California, Berkeley and copyrighted by the University of California. The ASM51 cross assembler bundled with Multisim MCU is a copyrighted product of MetaLink Corp. (www.metaice.com). HI-TECH C Compiler for PIC10/12/16 MCUs (Lite Edition), MPASM Macro Assembler, MPLINK Object Linker, and MPLIB Object Librarian and related documentation and literature is reproduced and distributed by National Instruments Ireland Resource Ltd. under license from Microchip Technology Inc. All rights reserved by Microchip Technology Inc. MICROCHIP SOFTWARE OR FIRMWARE AND LITERATURE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE SOFTWARE OR FIRMWARE OR THE USE OF OTHER DEALINGS IN THE SOFTWARE OR FIRMWARE. Anti-Grain Geometry - Version 2.4 Copyright (C) 2002-2004 Maxim Shemanarev (McSeem) Permission to copy, use, modify, sell and distribute this software is granted provided this copyright notice appears in all copies. This software is provided "as is" without express or implied warranty, and with no claim as to its suitability for any purpose. Anti-Grain Geometry - Version 2.4 Copyright (C) 2002-2005 Maxim Shemanarev (McSeem) 1. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 2. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 3. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Trademarks
LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks. Electronics Workbench, Multisim and Ultiboard are trademarks of National Instruments.
Portions of this product obtained under license from Bartels Systems GmbH. Other product and company names mentioned herein are trademarks or trade names of their respective companies. Members of the National Instruments Alliance Partner Program are business entities independent from National Instruments and have no agency, partnership, or joint-venture relationship with National Instruments.
Patents
For patents covering National Instruments products/technology, refer to the appropriate location: HelpPatents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. Some portions of this product are protected under United States Patent No. 6,560,572.
Conventions
The following conventions are used in this manual: The symbol leads you through nested menu items and dialog box options to a final action. The sequence ToolsClear ERC MarkersEntire design directs you to pull down the Tools menu, select the Clear ERC Markers item, and select Entire design from the resulting dialog box. This icon denotes a tip, which alerts you to advisory information. This icon denotes a note, which alerts you to important information. bold Bold text denotes items that you must select or click in the software, such as menu items and dialog box options. Bold text also denotes parameter names. Italic text denotes variables, emphasis, a cross-reference, or an introduction to a key concept. Italic text also denotes text that is a placeholder for a word or value that you must supply. Text in this font denotes text or characters that you should enter from the keyboard, sections of code, programming examples, and syntax examples. This font is also used for the proper names of disk drives, paths, directories, programs, subprograms, subroutines, device names, functions, operations, variables, filenames, and extensions.
italic
monospace
Contents
Chapter 1 Introduction to NI Circuit Design Suite
NI Circuit Design Suite Product Line............................................................................1-1 The Tutorials..................................................................................................................1-1
vii
Contents
Preparing for Manufacturing/Assembly ........................................................................ 3-19 Cleaning up the Board..................................................................................... 3-19 Adding Comments .......................................................................................... 3-19 Exporting a File............................................................................................... 3-19 Viewing Designs in 3D ................................................................................................. 3-20
viii
ni.com
Some of the described features may not be available in your edition of Circuit Design Suite. Refer to the NI Circuit Design Suite Release Notes for a list of the features available in your edition.
The Tutorials
This book contains the following step-by-step tutorials: Multisim TutorialIntroduces you to Multisim and its many functions. Ultiboard TutorialShows you how to place the components and traces for the circuit described in the Multisim Tutorial chapter. You will also learn how to autoplace parts and then autoroute them. Multisim MCU TutorialLeads you through the process of simulating and debugging a circuit that contains a microcontroller.
For more detailed information on the features discussed in these chapters, refer to the Multisim Help or the Ultiboard Help.
1-1
Multisim Tutorial
This chapter contains a tutorial that introduces you to Multisim and its many functions. Some of the described features may not be available in your edition of Circuit Design Suite. Refer to the NI Circuit Design Suite Release Notes for a list of the features available in your edition.
2-1
Chapter 2
Multisim Tutorial
1 2 3 4
5 6 7
The Menu Bar is where you find commands for all functions. The Design Toolbox is where you navigate through the different types of files in a project (schematics, PCBs, reports), view a schematics hierarchy and show or hide different layers. The Component toolbar contains buttons that you use to select components from the Multisim databases for placement in your schematic. The Standard toolbar contains buttons for commonly-performed functions such as Save, Print, Cut, and Paste.
2-2
ni.com
Chapter 2
Multisim Tutorial
The View toolbar contains buttons for modifying the way the screen is displayed. The Simulation toolbar contains buttons for starting, stopping, and other simulation functions. The Main toolbar contains buttons for common Multisim functions. The In Use List contains a list of all components used in the design. The Instruments toolbar contains buttons for each instrument. The Circuit Window (or workspace) is where you build your circuit designs. The Spreadsheet View allows fast advanced viewing and editing of parameters including component details such as footprints, RefDes, attributes and design constraints. You can change parameters for some or all components in one step and perform a number of other functions.
Overview
This tutorial leads you through the circuit design flow, from schematic capture, through simulation and analysis. After following the steps outlined on the following pages, you will have designed a circuit that samples a small analog signal, amplifies it and then counts the occurrences of the signal on a simple digital counter. Helpful tips are indicated by the presence of an icon in the left column, as in the tip below.
Tip
You can access the online help at any time by pressing <F1> on your keyboard, or by clicking on the Help button in a dialog box.
2-3
Chapter 2
Multisim Tutorial
Schematic Capture
In this section, you will place and wire the components in the circuit shown below.
Complete the following steps to save the file with a new name: 1. 2. Select FileSave As to display a standard Windows Save dialog. Navigate to the location where you wish the file to reside, enter
MyGettingStarted as the filename, and click the Save button.
2-4
ni.com
Chapter 2
Multisim Tutorial
Tip To guard against accidental loss of data, set up a timed auto-backup of the file in the Save tab of the Global Preferences dialog box.
Complete the following step to open an existing file: 1. Select FileOpen, navigate to the location where the file resides, highlight the file, and click on the Open button.
Tip
To view files from earlier versions of Multisim, select the desired version in the Files of Type drop-down in the Open dialog.
Tip Once you have selected the desired Group and Family, start typing the components name in the browsers Component field. As you type, the string appears in the Searching field at the bottom of the browser. In the example below, type seven_seg_decimal_com_a_blue. Matches are displayed as you type.
2-5
Chapter 2
Multisim Tutorial
3.
Move the cursor to the bottom-right of the workspace and left-click to place the component. Note that the Reference Designator for this component is U1.
2-6
ni.com
Chapter 2
Multisim Tutorial
4.
Place the remaining components in the Digital Counter area as shown below.
Note When placing resistors, inductors, or capacitors (RLC components), the Select a Component dialog box has slightly different fields than for other components. When placing these components, you can choose any combination of: the components value (for example, the resistance value); type (for example, carbon film); tolerance; footprint and manufacturer. If you are placing a component that will be ultimately exported to PCB layout, and become part of a Bill of Materials, you must be careful that the combination of values that you select in the Select a Component dialog box are available in a real-world, purchaseable component.
When placing RLC components, type the value of the device that you want to place in the field at the top of the Component list. The value does not need to appear in the list to be placed on the schematic.
Tip Tip
While placing the 200 resistor, rotate it to a vertical orientation by pressing <Ctrl-R> on your keyboard. Reference Designators (for example, U1, U2) are assigned in the order the components are placed. If you place components in a different order than in the original circuit, the numbering will differ. This will not affect the operation of the circuit in any way.
Tip
2-7
Chapter 2
Multisim Tutorial
5.
Place the components in the Counter Control section. After placement, right-click on each of the SPDT switches and select Flip Horizontal.
Tip Tip
When a component is on the workspace and you want to place the same component again, highlight it and select EditCopy, then EditPaste. You can also select it from the In Use List and click to place it on the workspace. 6. Place the components in the Analog Amplifier section as shown below, rotating as needed.
7.
Double-click on the AC voltage signal source and change the Voltage (Pk) to 0.2 V and click OK to close the dialog.
2-8 ni.com
Chapter 2
Multisim Tutorial
8.
9.
Tip Tip
Once you have wired a circuit, you can drop two-pinned components like resistors directly onto a wire. The connection is automatically made by Multisim.
2-9
Chapter 2
Multisim Tutorial
Complete the following steps to wire the circuit: 1. Click on a pin on a component to start the connection (your pointer turns into a crosshair) and move the mouse. A wire appears, attached to your cursor. Click on a pin on the second component to finish the connection. Multisim automatically places the wire, which conveniently snaps to an appropriate configuration, as shown below. This feature saves a great deal of time when wiring large circuits.
2.
Tip
You can also control the flow of the wire by clicking on points as you move the mouse. Each click fixes the wire to that point.
2-10
ni.com
Chapter 2
Multisim Tutorial
3.
Tip Use Bus Vector Connect to wire multi-pinned devices like U3 and R4 together in a bus. Refer to the Multisim Help for details. Tip
Virtual WiringTo avoid clutter, you can use virtual connections between the Counter Control and Digital Counter sections using on-page connectors.
2-11
Chapter 2
Multisim Tutorial
4.
Simulation
Simulating your circuits with Multisim catches errors early in the design flow, saving time and money.
Virtual Instrumentation
In this section, you will simulate the circuit and view the results with the virtual oscilloscope.
Tip You can also use Getting Started 2.ms11 from the Getting Started folder (found inside the samples folder).
1.
J1, J2 and R2 are interactive components. Set up the interactive keys for J1, J2 and R2 by double-clicking on each and selecting the Value tab. In the Key field, enter E for J1, L for J2, and A for R2.
2-12
ni.com
Chapter 2
Multisim Tutorial
2.
Press <E> on the keyboard to enable the counter, or just click on the widened switch arm that appears when you hover the cursor over J1. Enable is Active Low. Select SimulateInstrumentsOscilloscope to place the oscilloscope on the workspace. Wire the instrument as shown in step 5.
3.
Tip
To easily differentiate between traces on the oscilloscope, right-click on the wire connected to the scopes B input and select Color Segment from the context menu that displays. Select a color that differs from the wire connected to the A input, for example blue. (Changing wire color or performing any other editing function cannot be done while simulation is running.) 4. 5. Double-click on the scopes icon to show the instrument face. Select SimulateRun. The output of the opamp appears on the scope. Adjust the Timebase to 2 ms/Div and Channel As Scale to 500 mV/Div. You will see the following displayed on the scope.
As the circuit simulates, the 7-segment display counts up and the LED flashes at the end of each count cycle. 6. Press <E> on your keyboard while the simulation is running to enable or disable the counter. Enable is Active Low. Press <L> to load zeros into the counter. Load is Active Low.
2-13
Chapter 2
Multisim Tutorial
Press <Shift-A> to observe the effect of decreasing the potentiometers setting. Repeat, pressing <A> to increase.
Tip
Instead of pressing the above-mentioned keys, you can directly manipulate the interactive components on the schematic with your mouse.
Analysis
In this section, you will use AC Analysis to verify the frequency response of the amplifier. Complete the following steps to perform an AC Analysis at the output of the op-amp: 1. Double-click on the wire that is attached to pin 6 of the op-amp, and change the preferred net name to analog_out in the Net Settings dialog box. Select SimulateAnalysesAC Analysis and click on the Output tab.
2.
2-14
ni.com
Chapter 2
Multisim Tutorial
3.
Highlight V(analog_out) in the left column and click Add. V(analog_out) moves to the right column. This indicates the voltage at node V(analog_out) will be displayed after simulation. Click Simulate. The results of the analysis appear in the Grapher.
4.
The Grapher
The Grapher is a multi-purpose display tool that lets you view, adjust, save and export graphs and charts. It is used to display the results of all Multisim analyses in graphs and charts and a graph of traces for some instruments (for example the results of the oscilloscope). Complete the following steps to view results of a simulation on the Grapher: 1. 2. Run the simulation with the oscilloscope as described earlier. Select ViewGrapher.
2-15
Chapter 2
Multisim Tutorial
The Postprocessor
Use the Postprocessor to manipulate the output from analyses and plot the results on a graph or chart. Types of mathematical operations that can be performed on analysis results include arithmetic, trigonometric, exponential, logarithmic, complex, vector and logic.
Reports
You can generate a number of reports in Multisim: Bill of Materials (BOM), Component Detail Report, Netlist Report, Schematic Statistics, Spare Gates and the Cross Reference Report. This section uses the BOM as an example for the tutorial circuit.
2-16
ni.com
Chapter 2
Multisim Tutorial
Bill of Materials
A bill of materials lists the components used in your design and therefore provides a summary of the components needed to manufacture the circuit board. Information provided includes: quantity of each component needed. description of each component, including the type of component (example: resistor) and value (example: 5.1 kohm). Reference Designator of each component. package or footprint of each component.
Complete the following step to create a BOM (bill of materials) for your circuit: 1. Select ReportsBill of Materials. The report appears, looking similar to this:
To print the Bill of Materials, click the Print button. A standard Windows print dialog box appears, allowing you to choose the printer, number of copies, and so on. To save the Bill of Materials to a file, click the Save button. A standard Windows file save dialog box appears, where you specify the path and file name.
2-17
Chapter 2
Multisim Tutorial
Because the Bill of Materials is primarily intended to assist in procurement and manufacturing, it includes only real componentsit excludes components that are not real or available for purchase, such as sources or virtual components. Components without assigned footprints do not appear in the Bill of Materials. To see a list of components in your circuit that are not real components, click the Virtual button. A separate window appears, showing these components only. Detailed information on this and other reports can be found in the Multisim Help.
2-18
ni.com
Ultiboard Tutorial
The tutorial in this chapter places the parts and traces for the circuit described in Chapter 2, Multisim Tutorial. Some of the described features may not be available in your edition of Ultiboard. Refer to the NI Circuit Design Suite Release Notes for a list of the features available in your edition.
3-1
Chapter 3
Ultiboard Tutorial
1 2 3 4
5 6 7
The Menu Bar is where you find commands for all functions. The Standard toolbar contains buttons for commonly-performed functions such as Save, Print, Cut, and Paste. As you add more parts and traces to a board, it can become difficult to select only those which you want to use. The Select toolbar contains buttons used to control selections.
3-2
ni.com
Chapter 3
Ultiboard Tutorial
The Draw Settings toolbar is where you select the layer, thickness and unit of measure of a line or object that is being drawn. It also contains buttons for functions that control the appearance of lines and shapes drawn on a layer. The View toolbar contains buttons for modifying the way the screen is displayed. The Main toolbar contains buttons for common board design functions. The Autoroute toolbar contains autorouting and part placement functions. The Status Bar displays useful and important information. The Workspace is where you build your design. The Spreadsheet View allows fast advanced viewing and editing of parameters including part details such as shapes, Reference Designators, attributes and design constraints. The Design Toolbox lets you show, hide, or dim elements of your design. The 3D Preview shows you a three-dimensional preview of the board. The Birds Eye View shows you the design at a glance and lets you easily navigate around the workspace.
Select Getting Started.ewprj and click Open. The project file is loaded into Ultiboard.
Tip
For instructions on exporting a design from Multisim to Ultiboard, refer to the Multisim Help and the Ultiboard Help.
3-3
Chapter 3
Ultiboard Tutorial
4.
To select a design from the project (for example, GS1), either click on its tab, or click on its name in the Projects tab of the Design Toolbox.
Complete the following steps to experiment with the Board Wizard: 1. Double-click on Board Outline in the Layers tab to make it the active layer.
3-4
ni.com
Chapter 3
Ultiboard Tutorial
2. 3.
Click on the existing board outline in the GS1 design and press <Delete> on the keyboard. Choose ToolsBoard Wizard.
4. 5.
Enable the Change the layer technology option to make the Technology options available. Choose Multi-layers constructed with double-sided boards and single layer stack-ups, and click Next.
3-5
Chapter 3
Ultiboard Tutorial
The next dialog box is where you define the Lamination settings for the board. (For this tutorial you will not change settings.)
6.
Click Next. In the Board Wizard - Shape of Board dialog box: make sure the Reference Point is set to Bottom-left for Alignment. make sure the Rectangular option is selected for Board shape and size. set the Width to 3000 and the Height to 2000 (a more suitable size for the parts in this design). set the Clearance to 5.00000. This is the distance from the edge of the board that is to be kept free of parts or any other elements.
7.
Note
For complete details on the Board Wizard, refer to the Ultiboard Help.
3-6
ni.com
Chapter 3
Ultiboard Tutorial
Complete the following steps to move the board outline: 1. 2. Double-click on Board Outline in the Layers tab. Click anywhere on the board outline in the workspace and drag the board to a location just below the row of parts.
Complete the following steps to change the reference point: 1. 2. Select DesignSet Reference Point. The reference point is attached to your cursor. Move the cursor the the lower-left corner of the board outline and click to place it.
Placing Parts
You can place parts on your GS1 design file in several different ways:
Tip
select one or more parts from outside the board outline and drag them into place. use the Parts tab in the Spreadsheet View to locate parts and place them. select and place parts from the database.
Use the PlaceUnplace Parts command to quickly remove all non-locked parts from the PCB and experiment with a different placement technique.
3-7
Chapter 3
Ultiboard Tutorial
Tip
You can also search for a part with the EditFind command. While this command works much like a Find function in other applications, it also allows you to search for a part by name, number, shape, value, or by all variables. Refer to the Ultiboard Help for details.
3-8
ni.com
Chapter 3
Ultiboard Tutorial
2.
Click on U1 (the 7-segment display) and drag it to the location shown in the figure below.
U1 remains selected. This is an important point for Ultiboard that holds throughout the applicationyou need to explicitly end any particular action. In this case, simply clicking somewhere else de-selects the part. Right-clicking also ends the current action. 3. Go to the Parts tab in the Spreadsheet View and scroll to U1. You will notice that the green light beside the part is slightly brighterthis indicates that the part has been placed.
3-9
Chapter 3
Ultiboard Tutorial
2. 3.
Click on J3 and drag it from the Parts tab onto the workspace. J3 is attached to your mouse pointer. Drop J3 on the left edge of the board, roughly in the middle. As before, in the Parts tab J3s green light is slightly brighter, indicating that the part has been placed.
3-10
ni.com
Chapter 3
Ultiboard Tutorial
3.
4. 5. 6.
Click OK. The Get a Part From the Database dialog box disappears, and you are prompted to enter the RefDes and Value. Enter the holes reference designator (H1) and value (HOLE) and click OK. Move the pointer over the board. The part is attached to the pointer.
3-11
Chapter 3
Ultiboard Tutorial
7. 8. 9.
When the hole is in position in the top-left corner, click to drop it on the board. The Enter Reference Designation for Part dialog box reappears, with the reference designator automatically incremented to H2. Enter the value (HOLE) and click OK to place the next mounting hole in the top right corner, and repeat to place H3 in the bottom right corner, and H4 in the bottom left corner.
10. Click Cancel to stop, and click Cancel again to close the Get a Part From the Database dialog box.
Moving Parts
You can use the same methods for moving parts as you do for placing them. To select a part already on the board, simply click on it. To specify the X/Y coordinates to which the selected part is to move, press the <*> key on the numeric keypad. Alternatively, in the Parts tab, select a placed part (indicated by a bright green light beside it) and drag it to a new location.
Tip
The parts label and pads are separate elements from its shape. When selecting a part on the board, be sure to select the whole part, not just the label or pads. Use the Selection Filters to assist with this. Refer to the Ultiboard Help for more information.
Tip
Once a part is selected, you can also move it around on the board by pressing the arrow keys on your keyboard.
3-12
ni.com
Chapter 3
Ultiboard Tutorial
You can also select a group of parts and move them together. To do this, you can do one of the following: hold down the <Shift> key and click on more than one part. drag a box around several parts.
All the selected parts will move together when you drag the cursor. These are temporary groupsonce you select another part, the group connection is lost. To make a group that remains until you remove it, you can use the Group Editor. For details, refer to the Ultiboard Help.
Tip
Another option for moving parts is to use the EditAlign commands to align the edges of selected parts or to space them relative to each other. Use the EditAlign commands to align the mounting holes you just placed: 1. 2. 3. 4. 5. Select H1 and hold down the <Shift> key to select H2. Choose EditAlignAlign Top. If H2 was not originally placed exactly in line with H1, you will see it move. Click on an empty space on the board, then select H2 and H3. Choose EditAlignAlign Right. Continue in this manner to align the bottoms of H3 and H4, and the left sides of H1 and H4.
Placing Traces
You have the following options for placing traces: manual trace. follow-me trace. connection machine trace.
A manual trace is placed exactly as you specify, even running through a component or trace if that is the path you set out. A follow-me trace automatically draws a valid trace between the pins you select with your mouse movementsyou can move from pin to pin, leaving a valid trace. A connection machine trace automatically joins two pins by the most efficient route, though you have the option of changing it. As you place a trace, and before you click to fix it in place, you can always remove a segment by backing up over it. Each time you click while placing a manual trace, or each time a follow-me trace or connection machine trace
3-13
Chapter 3
Ultiboard Tutorial
changes direction, a separate segment of that trace is created. When performing operations on traces, be sure to select either the appropriate segment or, if you wish, the whole trace.
If necessary, press <F7> to show the whole design. Complete the following steps to place a trace manually: 1. Choose PlaceLine.
The Line command is used to create a line on any layer. The results differ depending on the layer selected. For example, if the selected layer is silkscreen, you will create a line on the silkscreen layer of the PCB. If the selected layer is a copper layer, then the line is actually a trace.
Tip
2.
Locate J3, toward the left-hand part of the board. Find the start pin shown below:
Part J3
Start Pin
Tip
You can turn off or dim the Force Vectors to see the nets more clearly. Do this using the Force Vectors checkbox in the Layers tab of the Design Toolbox. Refer to the Ultiboard Help for more information about Force Vectors.
3-14
ni.com
Chapter 3
Ultiboard Tutorial
Tip
If you have trouble locating the part, use the Find function of the Parts tab. Select the part in the Parts tab, then click the Find and select the part button. The part is shown in the workspace. If necessary, zoom in further using the mouse wheel. 3. Click on the pin specified in the above step. Ultiboard highlights all the pins that are part of the same net as the pin you clicked on with an X. (The color of the highlighting can be changed in the Colors tab of the Global Preferences dialog box.) This is how you know which pins to connect to match the connectivity from your schematic.
4.
Move the cursor in any direction. A green line (the trace) is attached to the selected pin. Each time you click, you anchor the trace segment, as shown in the figure below (2). Click on the destination pin.
5.
1 2
Destination Pin
6.
3-15
Chapter 3
Ultiboard Tutorial
7.
Click the Select button on the Main toolbar to exit line-placing mode.
Choose PlaceFollow-me. Click on the top pin of J3. Click on the second pin from the bottom on the left side of U4. Ultiboard draws the connection for you.
You do not need to click exactly on a pinyou can also start by clicking on a ratsnest
line.
Click Ratsnest
3.
Move your cursorUltiboard suggests various trace placement options routed around obstacles.
3-16 ni.com
Chapter 3
Ultiboard Tutorial
4.
When you see the route you want, click to fix the trace. You dont have to click on the ratsnest or the destination pin.
5.
Before autoplacing parts, pre-place and lock any parts that you do not wish to be moved during the autoplacement process. (The mounting holes, and U1, J1, J2, J3, and LED 1 in GS5 have been pre-placed and locked.) For details on locking parts, refer to the Ultiboard Help.
3-17
Chapter 3
Ultiboard Tutorial
1. 2.
Open the GS5 design in Ultiboard. Select AutorouteStart Autoplacement. The parts are placed on the circuit board.
Autorouting Traces
You can place traces in Ultiboard using the methods described earlier in this chapter, or automatically route the traces as described below. Complete the following steps to autoroute the traces in Getting Started.ewprj: 1. 2. Open the GS3 design in Ultiboard. Select AutorouteStart/Resume Autorouter. The workspace switches to Autorouter Mode and trace autorouting begins. As autorouting proceeds, you will see traces being placed on the board. When autorouting is complete, Autorouter Mode closes and you are returned to the workspace. 3. Optionally, select AutorouteStart Optimization to optimize the placement of the traces.
The autorouter can be stopped at any time and you can make manual changes as desired. When you restart the autorouter, it will continue with
3-18
ni.com
Chapter 3
Ultiboard Tutorial
the changes you made. Remember to lock any traces that you have placed manually and do not wish to be moved by the autorouter.
Tip
Use the Routing Options dialog box to modify autoplacement and autorouting options. Refer to the Ultiboard Help for details.
Adding Comments
Comments can be used to show engineering change orders, to facilitate collaborative work among team members, or to allow background information to be attached to a design. You can pin a comment to the workspace, or directly to a part. When a part with an attached comment is moved, the comment also moves. For details, refer to the Ultiboard Help.
Exporting a File
An exported file contains complete information describing how a finished board is to be manufactured. Files that can be exported include Gerber RS-274X and RS-274D files. For complete details, refer to the Ultiboard Help.
3-19
Chapter 3
Ultiboard Tutorial
Viewing Designs in 3D
Ultiboard lets you see what the board looks like in three dimensions at any time during the design. For complete details, refer to the Ultiboard Help.
Tip
You can use the Internal View to look between the layers of a multi-layer PCB. For details, refer to the Ultiboard Help.
3-20
ni.com
The tutorial in this chapter leads you through the process of simulating and debugging a circuit that contains a microcontroller. Some of the described features may not be available in your edition of Circuit Design Suite. Refer to the NI Circuit Design Suite Release Notes for a list of the features available in your edition.
Overview
The files used for this tutorial install with your NI Circuit Design Suite software at ...\samples\Getting Started. This tutorial uses Getting Started MCU.ms11, which accesses the contents of folder LCDWorkspace as required. The LCD Graphical Display circuit example demonstrates the use of a PIC microcontroller to control a graphical LCD display component in Multisim based on a combination of the Toshiba T6963C controller and an external display RAM. To control the LCD display, the microcontroller sends signals to the LCD through the LCDs data and control lines. A software program written for the microcontroller determines the logic behind setting the lines on its pins to high or low to send commands and data to the LCD display.
4-1
Chapter 4
4-2
ni.com
Chapter 4
LCDWorkspace. The workspace contains one project project1 that consists of a single source code file main.asm.
Complete the following steps to view the file: 1. Double-click on main.asm in the Design Toolbox. A tab appears in the schematic capture workspace called main.asm that displays the assembly program.
To display the line numbers, select MCUShow Line Numbers. Complete the following step to run this circuit: 1. Select SimulateRun. If you did not build your program beforehand, a dialog box displays stating that the configuration is out of date and asks if you would like to build it. Click Yes. The results of the build display in the Results tab of the Spreadsheet View. Switch back to the design tab. The program displays the line Graphical LCD T6963C for Multisim characters in text mode; the LCD then switches to graphical mode and draws an inverted V dot-by-dot on top of the text. Once the lines are drawn, the text scrolls right and then left. This is achieved by moving the start address of the text buffer of the LCD display. This also demonstrates that there are two buffers in the LCD, one for storing graphics and another for storing text. Other features of the LCD such as text flashing and erasing of characters are also demonstrated. The LCD display program continues to cycle through each of these effects. To stop the simulation, select SimulateStop.
4-3
Chapter 4
The text to be displayed on the LCD display is stored in data tables for some microcontrollers, but there is no PIC assembly instruction that allows you to directly address a data value in the program memory space. Instead, you can load literal values into the W register so you can write a routine that returns a value in your string based on an index. The RETLW instruction loads a constant value into the W register and executes a RETURN in one instruction.
4-4
ni.com
Chapter 4
The TXPRT routine retrieves the text data to be displayed on the LCD display. The character codes for the LCD display are defined in the T6963C controller reference manual (for example, 0x27 is the code for the letter G, 0x52 for r, and so on):
4-5
Chapter 4
Initialization The initialization code begins at the START label as shown in the excerpt below. The pins in the microcontroller are set up as output pins, and the values are reset. The LCD display component is initialized by the microcontroller and set to graphical and text mode. The home addresses for the internal graphical and text buffers in the LCD display component are set to 0x0000 and 0x2941 respectively, which determines where on the display the LCD starts to display the buffer data. Finally, the control signals are set up for the proper read/write operation on the LCD display.
4-6
ni.com
Chapter 4
Drawing Text and Graphics The rest of the program sends commands to the LCD graphical display via the control lines through MCU pins RA0 to RA2 and data through the data lines:
For example, the above excerpt from the main loop in the program sends the characters defined in the TXPRT subroutine to be displayed in text mode on the graphical LCD. The following sets the LCD to auto write mode:
MOVLW MOVWF CALL CMD_AWRON CMD_BUFFER CMD
At this point, the program starts counting, and executes through the loop LOOP_READ_DATA2 35 times. This loop calls TXPRT to retrieve the text
4-7
Chapter 4
data and load it into the W register. It then calls to the subroutine ADT, which calls SEND_DATA, which writes the values in the W register to port B, to be sent to the data lines of the LCD display. Once the data is sent, the proper value on port A of the microcontroller is sent to the control pins of the LCD display to let it know that the data is ready to be read. The subroutines all return at the end to the instruction just after the call to them and the same thing happens until all 35 characters have been transmitted. The final three instructions in the excerpt turn off the auto write mode in the LCD display after exiting the loop:
MOVLW MOVWF CALL CMD_AWROFF CMD_BUFFER CMD
The next few instructions draw the horizontal and sloped lines in graphical mode:
;6 draw wave once MOVF BTFSC CALL ADDR_L, 0 STATUS, Z DRAW_WAVE
During simulation, additional debugging information displays to help you understand what is happening inside the MCU. For example, you can switch between viewing events happening in the high level source and at
4-8
ni.com
Chapter 4
the assembly instruction level which also displays the actual opcodes for each instruction that are being executed by the MCU. The source code view is not capable of displaying all this extra information. Instead, each MCU component in the circuit design has its own Debug View that displays debugging information. Complete the following steps to access the Debug View: 1.
Note
The Debug View is available only after you have successfully built your code, so the preceding step is only necessary once. 2. Select MCUMCU PIC 16F84A U1Debug View. Or Use the right-click context menu on an item in the MCU workspace of the Design Toolbox.
Another tab opens in the schematic capture workspace called Debug(<reference designator of MCU>), in this case Debug(U1).
4-9
Chapter 4
Drop-down List
Use the drop-down list at the top of the Debug View to select between the disassembly instructions generated internally by Multisim and the listing file generated by the assembler or compiler (the format of the listing file is dependant on the tool that you choose to build your code). In the LCD graphical display example, the code was written in assembly and built by the Microchip assembly tools. The Microchip assembler generates a listing file (.lst) that contains all of the opcodes generated for each assembly instruction. The debug listing view displays information from this listing file. Multisim generates the disassembly format using its internal disassembler to disassemble the opcode instructions into assembly instructions. This format is not necessary for this example since the debug listing contains all of the information needed. In cases where an MCU project loads only the machine code (.hex) file, the disassembly view shows the disassembled opcode instructions so that you can see whats happening in the MCU. Since no listing file for MCU projects of this type is available, the disassembly view is very useful.
4-10
ni.com
Chapter 4
Adding a Breakpoint
You can add breakpoints in the source code view when simulation has stopped, as well as during simulation. You can add breakpoints to a microcontroller project in two ways. One way is to add them in the source code view. In this example, the main.asm tab in the schematic capture workspace is the only source code view available.
Note
If your MCU design contains more than one file, there will be a source code view for each of your source code files. You can also set a breakpoint in the Debug View window. You can set breakpoints in the disassembly view or the debug listing view, but for this example, you will only use the debug listing view.
Grey Column
Complete the following steps to add a breakpoint in the source code view: 1. 2. 3. 4. Open the Debug View for U1. Double-click on main.asm in the Design Toolbox. Scroll to the line just below the START label: BCF STATUS, RP0. Double-click on the first (grey) column on the left side of the
main.asm window next to the line BCF STATUS, RP0. A red circle
appears at that location indicating that a breakpoint has been set at that line.
4-11
Chapter 4
5.
Select SimulateRun. The simulation automatically pauses at the breakpoint that you have just set. The Debug View automatically displays with a yellow arrow showing where the MCU program execution is paused.
Complete the following step to remove the breakpoint: 1. Double-click on the breakpoint in the Debug View or the main.asm source code view. Or Select MCURemove all breakpoints to remove all breakpoints.
Note
You can add and remove breakpoints in the Debug View in the same manner as the source code view.
3. 4.
4-12
ni.com
Chapter 4
5.
Select MCUMCU PIC16F84A U1Memory View to view the current state of the memory inside the microcontroller U1. Notice that the value of the program counter PC in the IROM section is one higher than the address value of the line the yellow arrow is pointing to. In the example in the above figure, the address in the Debug View is 192 and the PC value in the Memory View is 193.
Note
If the MCU has not finished executing the current command when you pause the simulation, the value in the program counter will be the same as the address value. You can also look at the other sections of the Memory View to see the values inside the other parts of memory in the microcontroller. 6. 7. 8. Click the Step into button in the Simulation tool bar. The current instruction is executed and the simulation pauses at the next instruction. Select SimulateStop.
4-13
Chapter 4
The simulation executes all of the remaining instructions in the SEND_DATA subroutine and pauses at the first instruction after the call to the SEND_DATA subroutine.
Run to Cursor
1. 2. 3. Select MCURemove All Breakpoints. Click on a line inside the SEND_DATA subroutine since we know that this subroutine will be called again to send data to the LCD display. Click the Run to Cursor button in the Simulation toolbar. The simulation runs until the MCU hits the instruction that you clicked on inside the SEND_DATA subroutine. It then pauses and places the yellow arrow next to that line.
4-14
ni.com
Visit the following sections of the award-winning National Instruments Web site at ni.com for technical support and professional services: SupportTechnical support at ni.com/support includes the following resources: Self-Help Technical ResourcesFor answers and solutions, visit ni.com/support for software drivers and updates, a searchable KnowledgeBase, product manuals, step-by-step troubleshooting wizards, thousands of example programs, tutorials, application notes, instrument drivers, and so on. Registered users also receive access to the NI Discussion Forums at ni.com/forums. NI Applications Engineers make sure every question submitted online receives an answer. Standard Service Program MembershipThis program entitles members to direct access to NI Applications Engineers via phone and email for one-to-one technical support as well as exclusive access to on demand training modules via the Services Resource Center. NI offers complementary membership for a full year after purchase, after which you may renew to continue your benefits. For information about other technical support options in your area, visit ni.com/services, or contact your local office at ni.com/contact. Training and CertificationVisit ni.com/training for self-paced training, eLearning virtual classrooms, interactive CDs, and Certification program information. You also can register for instructor-led, hands-on courses at locations around the world. System IntegrationIf you have time constraints, limited in-house technical resources, or other project challenges, National Instruments Alliance Partner members can help. To learn more, call your local NI office or visit ni.com/alliance.
A-1
Appendix A
If you searched ni.com and could not find the answers you need, contact your local office or NI corporate headquarters. Phone numbers for our worldwide offices are listed at the front of this manual. You also can visit the Worldwide Offices section of ni.com/niglobal to access the branch office Web sites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.
A-2
ni.com
Index
Numerics
3D designs in Ultiboard, 3-20
E
examples (NI resources), A-1 exporting files from Ultiboard, 3-19
A
analysis, 2-14 assembly program, 4-4 autoplacement, 3-17 autorouting, 3-18
F
follow-me trace, 3-16
G
grapher, 2-15
B
bill of materials, 2-17 board clean-up, 3-19 board outline, 3-4 BOM, 2-17 break and step, 4-12 break and step into, 4-14 break and step out, 4-14 break and step over, 4-14 breakpoint, 4-11
H
help, technical support, A-1
I
instrument drivers (NI resources), A-1 interface elements, 2-1, 3-1
K C
comments, 3-19 connection machine trace, 3-16 conventions used in the manual, v KnowledgeBase, A-1
M
manual trace, 3-14 manufacturing/assembly, 3-19 MCU debugging features, 4-8 MCU debugging overview, 4-8 MCU tutorial, 4-2 MCU tutorial overview, 4-1 moving parts in Ultiboard, 3-12 Multisim tutorial overview, 2-3
D
diagnostic tools (NI resources), A-1 documentation conventions used in the manual, v NI resources, A-1 dragging parts, 3-8, 3-10 drivers (NI resources), A-1
I-1
Index
N
National Instruments support and services, A-1 NI support and services, A-1
T
technical support, A-1 training and certification (NI resources), A-1 troubleshooting (NI resources), A-1 tutorial descriptions, 1-1 two-pinned components dropping directly onto a wire, 2-9
O
opening Multisim files, 2-4 opening Ultiboard tutorial, 3-3
U
user interface elements, 2-1
P
placing components in Multisim, 2-5 placing parts in Ultiboard, 3-7, 3-10 placing traces in Ultiboard, 3-13 placing Ultiboard dB parts, 3-11 postprocessor, 2-16 products, 1-1 programming examples (NI resources), A-1
V
virtual instruments, 2-12
W
Web resources, A-1 wiring components in Multisim, 2-9
R
reports, 2-16 run to cursor, 4-14
S
saving Multisim files, 2-4 schematic capture, 2-4 simulation, 2-12 software (NI resources), A-1 support, technical, A-1
I-2
ni.com
Support
Deutschsprachige Niederlassungen National Instruments National Instruments Germany GmbH Ges.m.b.H. Ganghoferstr. 70 b Plainbachstrae 12 80339 Mnchen 5101 Salzburg-Bergheim Tel.: +49 89 7413130 Tel.: +43 662 457990-0 Fax: +49 89 7146035 Fax: +43 662 457990-19 Lokaler technischer Support Deutschland: ni.germany@ni.com sterreich: ni.austria@ni.com Schweiz: ni.switzerland@ni.com Technischer Support und Produktinformation weltweit ni.com
National Instruments Switzerland Sonnenbergstrae 53 CH-5408 Ennetbaden Tel.: +41 56 2005151, +41 21 3205151 (Lausanne) Fax: +41 56 2005155
National Instruments Corporate Firmenhauptsitz 11500 North Mopac Expressway Austin, Texas 78759-3504 Internationale Niederlassungen
Australien 1800 300 800, Belgien 32 (0) 2 757 0020, Brasilien 55 11 3262 3599, China 86 21 5050 9800, Dnemark 45 45 76 26 00, Finnland 358 (0) 9 725 72511, Frankreich 01 57 66 24 24, Grobritannien 44 0 1635 523545, Indien 91 80 41190000, Israel 972 3 6393737, Italien 39 02 41309277, Japan 0120-527196, Kanada 800 433 3488, Korea 82 02 3451 3400, Libanon 961 (0) 1 33 28 28, Malaysia 1800 887710, Mexiko 01 800 010 0793, Neuseeland 0800 553 322, Niederlande 31 (0) 348 433 466, Norwegen 47 (0) 66 90 76 60, Polen 48 22 328 90 10, Portugal 351 210 311 210, Russland 7 495 783 6851, Schweden 46 (0) 8 587 895 00, Singapur 1800 226 5886, Slowenien 386 3 425 42 00, Spanien 34 91 640 0085, Sdafrika 27 0 11 805 8197, Taiwan 886 02 2377 2222, Thailand 662 278 6777, Tschechische Republik 420 224 235 774, Trkei 90 212 279 3031 Weitere Informationen finden Sie im Anhang unter Technische Untersttzung und professioneller Service. Fr Kommentare und Anregungen zu unserer Dokumentation geben Sie bitte auf unserer Website ni.com/info den Infocode feedback ein. 20062010 National Instruments Corporation. Alle Rechte vorbehalten.
Wichtige Informationen
Garantie
National Instruments gewhrleistet, dass die Datentrger, auf denen National Instruments Software bermittelt wird, whrend eines Zeitraums von 90 Tagen ab Lieferung, nachgewiesen durch Empfangsbesttigung oder sonstige Unterlagen, nicht aufgrund von Material- und Verarbeitungsfehlern Programmanweisungen nicht ausfhren. Datentrger, die Programmanweisungen nicht ausfhren, werden nach Wahl von National Instruments entweder repariert oder ersetzt, sofern National Instruments whrend der Garantiezeit ber derartige Mngel informiert wird. Damit Gegenstnde zur Ausfhrung von Garantieleistungen angenommen werden, mssen Sie sich eine Warenrcksendenummer (RMA-Nummer) vom Hersteller geben lassen und diese auf der Packung deutlich sichtbar angeben. Die Kosten der Rcksendung von Ersatzteilen, die von der Garantie erfasst sind, an Sie bernimmt National Instruments. National Instruments geht davon aus, dass die Informationen in diesem Dokument zutreffend sind. Das Dokument ist sorgfltig auf technische Richtigkeit berprft worden. Fr den Fall, dass dennoch technische oder Schreibfehler vorhanden sein sollten, behlt sich National Instruments das Recht vor, dies in spteren Ausgaben ohne vorherige Ankndigung zu berichtigen. Bitte wenden Sie sich an National Instruments, falls Sie einen Fehler vermuten. National Instruments haftet in keinem Fall fr Schden, die sich aus oder im Zusammenhang mit diesem Dokument oder den darin enthaltenen Informationen ergeben. SOWEIT HIER NICHT AUSDRCKLICH VORGESEHEN, SCHLIESST NATIONAL INSTRUMENTS JEDE GEWHRLEISTUNG, SEI SIE AUSDRCKLICH ODER STILLSCHWEIGEND, AUS. DIESER AUSSCHLUSS GILT INSBESONDERE FR EINE ETWAIGE KONKLUDENTE GEWHRLEISTUNG, DASS DIE PRODUKTE VON DURCHSCHNITTLICHER QUALITT UND FR DEN NORMALEN GEBRAUCH ODER FR EINEN BESTIMMTEN ZWECK GEEIGNET SIND. EINE SCHADENERSATZPFLICHT FR SCHULDHAFTES VERHALTEN SEITENS NATIONAL INSTRUMENTS IST AUF DEN VOM KUNDEN GEZAHLTEN KAUFPREIS BEGRENZT. NATIONAL INSTRUMENTS HAFTET NICHT FR SCHDEN, DIE SICH AUS DEM VERLUST VON DATEN, ENTGANGENEM GEWINN ODER NUTZUNGSMGLICHKEITEN ERGEBEN UND AUCH NICHT FR ZUFLLIGE ODER FOLGESCHDEN, SELBST WENN NATIONAL INSTRUMENTS AUF DIE MGLICHKEIT SOLCHER SCHDEN HINGEWIESEN WURDE. Diese Haftungsbegrenzung gilt unabhngig vom Rechtsgrund der Haftung. Ansprche gegenber National Instruments mssen innerhalb eines Jahres nach Schadenseintritt gerichtlich geltend gemacht werden. Die Firma National Instruments haftet nicht fr Versptungsschden, die nicht in ihrem Verantwortungsbereich liegen. Diese Garantie erstreckt sich nicht auf Schden, Fehler, Fehlfunktionen oder Servicemngel, die auf der Nichtbefolgung von Anweisungen von National Instruments fr die Installation, den Betrieb oder die Wartung, auf Vernderungen des Produktes, Missbrauch oder Fehlgebrauch des Produktes, auf einer Unterbrechung der Energieversorgung, Feuer, Wasserschden, Unflle, Handlungen Dritter oder anderen Geschehnissen, die nicht im Verantwortungsbereich von National Instruments liegen, beruhen.
Urheberrechte
Gem den Bestimmungen des Urheberrechts darf diese Publikation ohne vorherige schriftliche Zustimmung der Firma National Instruments Corporation weder vollstndig noch teilweise vervielfltigt oder verbreitet werden, gleich in welcher Form, ob elektronisch oder mechanisch. Das Verbot erfasst u. a. das Fotokopieren, das Aufzeichnen, das Speichern von Informationen in Retrieval Systemen sowie das Anfertigen von bersetzungen gleich welcher Art. National Instruments achtet das geistige Eigentum anderer und fordert seine Nutzer auf, dies ebenso zu tun. Die Software von National Instruments ist urheberrechtlich und durch andere Rechtsvorschriften zum Schutz geistigen Eigentums geschtzt. Wenn Sie NI Software nutzen, um Software oder andere Materialien, die im Eigentum Dritter stehen, zu vervielfltigen, drfen Sie NI Software nur insoweit nutzen, als Sie die betreffenden Materialien nach den jeweils anwendbaren Lizenzbestimmungen oder Rechtsvorschriften vervielfltigen drfen. BSIM3 and BSIM4 are developed by the Device Research Group of the Department of Electrical Engineering and Computer Science, University of California, Berkeley and copyrighted by the University of California. The ASM51 cross assembler bundled with Multisim MCU is a copyrighted product of MetaLink Corp. (www.metaice.com). HI-TECH C Compiler for PIC10/12/16 MCUs (Lite Edition), MPASM Macro Assembler, MPLINK Object Linker, and MPLIB Object Librarian and related documentation and literature is reproduced and distributed by National Instruments Ireland Resource Ltd. under license from Microchip Technology Inc. All rights reserved by Microchip Technology Inc. MICROCHIP SOFTWARE OR FIRMWARE AND LITERATURE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE SOFTWARE OR FIRMWARE OR THE USE OF OTHER DEALINGS IN THE SOFTWARE OR FIRMWARE. Anti-Grain Geometry - Version 2.4 Copyright (C) 2002-2004 Maxim Shemanarev (McSeem) Permission to copy, use, modify, sell and distribute this software is granted provided this copyright notice appears in all copies. This software is provided as is without express or implied warranty, and with no claim as to its suitability for any purpose. Anti-Grain Geometry - Version 2.4 Copyright (C) 2002-2005 Maxim Shemanarev (McSeem) 1. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 2. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 3. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Marken
Die Bezeichnungen LabVIEW, National Instruments, NI, ni.com, das National Instruments Geschftslogo (Wort-/Bildmarke) und das Adler Logo (Bildmarke) sind als Marken fr National Instruments Corporation geschtzt. Informationen ber weitere Marken von National Instruments finden Sie im Internet unter ni.com/trademarks im Bereich Trademark Information. Electronics Workbench, Multisim and Ultiboard are trademarks of National Instruments. Portions of this product obtained under license from Bartels Systems GmbH. Sonstige hierin erwhnte Produkt- und Firmenbezeichnungen sind Marken oder Handelsnamen der jeweiligen Unternehmen. Mitglieder des National Instruments Alliance Partner Programms sind eigenstndige und von National Instruments unabhngige Unternehmen; zwischen ihnen und National Instruments besteht keine gesellschaftsrechtliche Verbindung und auch kein Auftragsverhltnis.
Patente
Nhere Informationen ber den Patentschutz von Produkten oder Technologien von National Instruments finden Sie unter HilfePatente in Ihrer Software, in der Datei patents.txt auf Ihrem Datentrger oder in den Patentinformationen von National Instruments auf ni.com/patents. Some portions of this product are protected under United States Patent No. 6,560,572.
kursiv
monospace
Inhaltsverzeichnis
Kapitel 1 Einfhrung in die NI Circuit Design Suite
NI Circuit Design Suite..................................................................................................1-1 Einfhrungen .................................................................................................................1-1
vii
Inhaltsverzeichnis
Automatische Leiterbahnfhrung.................................................................................. 3-21 Vorbereitung fr die Leiterplattenfertigung .................................................................. 3-22 Aufrumen der Leiterplatte (Clean-Up).......................................................... 3-23 Hinzufgen von Kommentaren ....................................................................... 3-23 Exportieren von Dateien ................................................................................. 3-23 3D-Ansicht von Schaltungen......................................................................................... 3-24
viii
ni.com
Einige der hier genannten Funktionen sind mglicherweise nicht in Ihrer Version der Circuit Design Suite verfgbar. Der Funktionsumfang Ihrer Edition ist in den Versionshinweisen zur NI Circuit Design Suite beschrieben.
Einfhrungen
Dieses Handbuch enthlt folgende Einfhrungen: Einfhrung in MultisimStellt Ihnen Multisim und seine Funktionen vor. Einfhrung in UltiboardZeigt Ihnen, wie Sie die Bauelemente und Leiterbahnen fr die im Multisim-Kapitel beschriebenen Schaltungen richtig platzieren. Auerdem lernen Sie, wie die automatische Funk-
1-1
Kapitel 1
tion zum Einfgen von Bauelementen und Verlegen von Leiterbahnen verwendet wird. Einfhrung in Multisim MCUFhrt Sie durch die Simulation und Fehlersuche in einer Schaltung mit Mikrocontroller.
Weiterfhrende Informationen zu den in diesen Kapiteln beschriebenen Funktionen finden Sie in der Hilfe zu Multisim oder der Hilfe zu Ultiboard.
1-2
ni.com
Einfhrung in Multisim
Im vorliegenden Kapitel erhalten Sie eine kurze Einfhrung in Multisim und seine Funktionen. Einige der hier genannten Funktionen sind mglicherweise nicht in Ihrer Version der Circuit Design Suite verfgbar. Der Funktionsumfang Ihrer Edition ist in den Versionshinweisen zur NI Circuit Design Suite beschrieben.
Multisim-Benutzeroberflche
Multisim ist das Programm der NI Circuit Design Suite, mit dem Schaltplne erstellt und simuliert werden. Die Circuit Design Suite von National Instruments ist ein Softwarepaket zur automatisierten Elektronik-Entwicklung, die Ihnen die wichtigsten Schritte in der Schaltungsentwicklung erleichtert. In Multisim knnen Sie einen Schaltplan erstellen, Schaltungen simulieren und die Daten an den nchsten Arbeitsgang (z. B. Leiterplattenbestckung) exportieren.
2-1
Kapitel 2
Einfhrung in Multisim
1 2 3 4 5
6 7 8 9
10 11 12 13
Die Menleiste enthlt die Befehle fr smtliche Funktionen. Mit den Schaltungswerkzeugen knnen Sie nach verschiedenen Dateien eines Projekts suchen (z. B. Schaltplnen, Leiterplatten-Layouts oder Berichten), die Schaltplanhierarchie aufrufen und die darzustellenden Lagen auswhlen. ber die Schaltflchen der Symbolleiste Bauelemente knnen Sie Bauelemente auswhlen, die Sie in Ihre Schaltung einfgen mchten.
2-2
ni.com
Kapitel 2
Einfhrung in Multisim
Die Symbolleiste Standard enthlt Schaltflchen fr die meistverwendeten Funktionen wie Speichern, Drucken, Ausschneiden oder Einfgen. Die Symbolleiste Ansicht enthlt Schaltflchen zum ndern der Bildschirmanzeige. Die Symbolleiste Simulation enthlt Schaltflchen zum Steuern von Simulationen. Die Hauptleiste enthlt Schaltflchen fr allgemeine MultisimFunktionen. Die Liste verwendeter Bauelemente enthlt eine Liste aller in der Schaltung verwendeten Bauelemente. Die Symbolleiste Instrumente enthlt Schaltflchen fr jedes Instrument. Im Schaltungsfenster (auch als Arbeitsbereich bezeichnet) wird der Schaltplan dargestellt. Die Tabellenansicht ermglicht die Anzeige von Parametern und Angaben zu Bauelementen wie Platzbedarfsinformationen, Referenzbezeichnungen, Attribute und Entwurfsregeln. Hier knnen Sie z. B. die Parameter mehrerer Bauelemente gleichzeitig ndern.
berblick
Dieses Dokument beleuchtet alle Aspekte der Erstellung einer technischen Schaltung vom Entwurf eines Schaltplans ber die Simulation der Schaltung bis hin zur Analyse der Ergebnisse. Nach dem Abarbeiten der beschriebenen Schritte erstellen Sie eine Schaltung, mit der ein analoges Kleinsignal erfasst und verstrkt wird und dessen Auftreten mit einem einfachen digitalen Zhler ermittelt wird. Ntzliche Tipps sind links durch ein Symbol gekennzeichnet, z. B.:
Tipp Sie knnen jederzeit die Hilfe aufrufen, indem Sie die <F1>-Taste drcken oder in
2-3
Kapitel 2
Einfhrung in Multisim
Schaltplan
In diesem Abschnitt fgen Sie die Bauelemente fr die unten abgebildete Schaltung ein und verbinden sie miteinander.
So speichern Sie die Datei unter einem anderen Namen: 1. 2. Whlen Sie DateiSpeichern unter. Es ffnet sich das WindowsDialogfeld zum Speichern von Dateien. Whlen Sie einen Speicherort fr die Datei aus. Geben Sie anschlieend als Dateinamen MeineErstenSchritte ein und klicken Sie auf die Schaltflche Speichern.
2-4
ni.com
Kapitel 2
Einfhrung in Multisim
Tipp Um Datenverlust vorzubeugen, sollten Sie ber die Registerkarte Speichern des
Dialogfelds Allgemeine Einstellungen regelmig Sicherungskopien erstellen. Zum ffnen einer vorhandenen Datei gehen Sie wie folgt vor: 1. Klicken Sie auf DateiDatei ffnen, whlen Sie eine Datei aus und klicken Sie auf die Schaltflche ffnen.
Tipp Zum ffnen von Dateien aus lteren Multisim-Versionen whlen Sie im Dialogfeld
Tipp Nach Auswahl der Gruppe und Familie des Bauelements knnen Sie unter
Bauelement den Namen des Bauelements eingeben. Ihre Eingabe wird im Feld Suche am unteren Rand des Fensters angezeigt. Geben Sie fr das obige Beispiel seven_seg_decimal_com_a_blue ein. bereinstimmungen werden bereits bei der Eingabe angezeigt.
2-5
Kapitel 2
Einfhrung in Multisim
3.
Bewegen Sie den Cursor in die rechte untere Ecke der Arbeitsflche und klicken Sie mit der linken Maustaste, um das Bauelement einzufgen. Die Kennung fr dieses Bauelement lautet U1.
2-6
ni.com
Kapitel 2
Einfhrung in Multisim
4.
Fgen Sie die restlichen Bauelemente wie dargestellt in den Bereich fr den Zhler ein.
Beim Einfgen von Widerstnden, Spulen oder Kondensatoren (RLC-Bauelementen) enthlt das Dialogfeld Bauelement auswhlen geringfgig andere Optionen als sonst. Beim Einfgen der Bauelemente knnen Sie eine beliebige Kombination der folgenden Parameter whlen: Wert des Bauelements (z. B. Widerstandswert), Typ (z. B. Kohleschicht), Toleranz, Footprint und Hersteller. Beim Einfgen eines Bauelements, das spter in ein PCB-Layout exportiert und in die Stckliste aufgenommen werden soll, mssen Sie darauf achten, dass die im Dialogfeld Bauelement auswhlen angegebene Kombination von Werten auch wirklich verfgbar ist.
Hinweis Tipp Beim Einfgen von RLC-Bauelementen ist der Wert des Bauelements ganz oben in
die Liste der Bauelemente einzutragen. Der Wert muss aber nicht in der Liste enthalten sein, damit das Bauelement in die Schaltung eingefgt werden kann.
Tipp Um den 200--Widerstand senkrecht anzuordnen, drcken Sie beim Einfgen des
Reihenfolge, in der die Bauelemente eingefgt werden (z. B. U1, U2, U3). Wenn Sie also die Bauelemente in einer anderen Reihenfolge als in der Abbildung einfgen, ndert sich auch die Nummerierung entsprechend. Dies hat jedoch keinerlei Einfluss auf die Funktion der Schaltung.
2-7
Kapitel 2
Einfhrung in Multisim
5.
Fgen Sie die Bauelemente fr die Steuerung des Zhlers ein. Klicken Sie nach dem Einfgen mit der rechten Maustaste auf jeden SPDT-Schalter und whlen Sie Horizontal kippen.
Tipp Die SPDT-Schalter befinden sich in der Gruppe Basic und der Familie Switch. Tipp Wenn das bentigte Bauelement schon im Schaltplan vorhanden ist, markieren Sie
es, whlen Sie BearbeitenKopieren und dann BearbeitenEinfgen. Sie knnen es auerdem aus der Liste der verwendeten Bauelemente auswhlen und durch einen Klick in den Schaltplan einfgen. 6. Fgen Sie die Bauelemente fr den Analogverstrker wie dargestellt ein und drehen Sie sie bei Bedarf.
2-8
ni.com
Kapitel 2
Einfhrung in Multisim
7.
Klicken Sie doppelt auf die Wechselspannungsquelle und ndern Sie Spitzenspannung (Pk) in 0,2 V und klicken Sie zum Schlieen des Dialogfelds auf OK. Fgen Sie die Bauelemente fr die berbrckungskondensatoren wie dargestellt ein.
8.
9.
Fgen Sie den Kollektor und die dazugehrigen Bauelemente ein (vgl. die Abbildung unten).
Tipp J3 befindet sich in der Gruppe Basic und der Familie Connectors. Tipp Nach dem Verdrahten einer Schaltung knnen Sie Bauelemente mit zwei Anschls-
sen z. B. Widerstnde einfach auf eine Verbindung legen. Multisim fgt das Bauelement dann automatisch in den Stromkreis ein.
2-9
Kapitel 2
Einfhrung in Multisim
Um Bauelemente zu verbinden, fhren Sie die folgenden Schritte aus: 1. Klicken Sie den Ausgangspunkt fr die Verbindung an (der Cursor verwandelt sich daraufhin in ein Fadenkreuz) und bewegen Sie die Maus. Daraufhin erscheint unter dem Cursor eine Linie, die eine Leiterbahn symbolisieren soll. Klicken Sie auf den Pin des zweiten Bauelements, an dem die Verbindung enden soll. Multisim erstellt daraufhin eine Leiterbahn und fgt diese, wie unten dargestellt, automatisch an der richtigen Stelle und in der richtigen Konfiguration ein. Diese Funktion spart insbesondere beim Verbinden groer Schaltungen viel Zeit.
2.
Tipp Die Lage der Leiterbahn kann durch Mausklicks bestimmt werden. Bei jedem Klick
2-10
ni.com
Kapitel 2
Einfhrung in Multisim
3.
Verbinden Sie die restlichen Bauelemente fr den Zhlerbaustein entsprechend der Darstellung.
Tipp Mit Hilfe von Busvektorverbindungen knnen die Verbindungen von Bauele-
menten mit mehreren Pins (z. B. U3 und R4) als Busleitung gefhrt werden. Einzelheiten dazu entnehmen Sie bitte der Hilfe zu Multisim.
Tipp Damit die Verbindung nicht zu unbersichtlich wird, knnen Sie zwischen den
Abschnitten Counter Control und Digital Counter mit Hilfe von seitenspezifischen Steckverbindern virtuelle Verbindungen herstellen.
2-11
Kapitel 2
Einfhrung in Multisim
4.
Verdrahten Sie den Rest der Schaltung entsprechend der folgenden Abbildung.
Simulation
Durch Simulation einer Schaltung mit Multisim lassen sich schon frh Schaltungsfehler erkennen, wodurch Zeit und Geld gespart wird.
Virtuelle Messinstrumente
In diesem Abschnitt wird die Schaltung simuliert und das Ergebnis mit Hilfe eines virtuellen Oszillographen angezeigt.
Tipp Um Zeit zu sparen, knnen Sie aber auch die Datei Getting Started 2.ms11 aus dem Ordner Getting Started verwenden, der sich unter samples befindet.
1.
J1, J2 und R2 sind interaktive Bauelemente. Um die Bedientasten fr J1, J2 und R2 festzulegen, klicken Sie die Bauelemente doppelt an und klicken Sie auf die Registerkarte Wert. Geben Sie in das Feld Umschalttaste fr J1 E ein, fr J2 L und fr R2 A.
2-12
ni.com
Kapitel 2
Einfhrung in Multisim
2.
Zur Aktivierung des Zhlers drcken Sie die Taste <E> oder klicken Sie auf die verbreiterte Linie, die angezeigt wird, wenn sich der Cursor ber J1 befindet. Der Aktivierungseingang ist low-aktiv. Um einen Oszillographen einzufgen, whlen Sie Simulieren InstrumenteOszillograph. Verbinden Sie das Gert wie im Schritt 5 dargestellt mit der restlichen Schaltung.
3.
Tipp Um einfach zwischen den Kurven auf dem Oszillographen zu unterscheiden, klicken Sie die Leitung, die zum Eingang B des Gerts fhrt, mit der rechten Maustaste an und whlen Sie aus dem Kontextmen die Option Segment einfrben aus. Whlen Sie eine andere Farbe als die der Leitung an Eingang A aus, z. B. Blau (um die Farbe oder eine andere Einstellung zu ndern, muss die Simulation gestoppt werden.)
4.
Klicken Sie das Symbol fr den Oszillographen doppelt an, um die Vorderseite des Gerts mit der Anzeige und den Bedienknpfen einzublenden. Whlen Sie SimulierenStart. Im Oszillographen wird nun das Ausgangssignal des Operationsverstrkers angezeigt. Stellen Sie die Skalierung der Zeitbasis auf 2 ms pro Skalenteil und die Empfindlichkeit von Kanal A auf 500 mV pro Skalenteil ein. Der Oszillograph zeigt die Kurven dann folgendermaen an:
5.
Whrend der Simulation der Schaltung zhlt die 7-Segment-Anzeige aufwrts. Wenn der Zhler einmal durchgezhlt hat, leuchtet eine LED auf.
2-13
Kapitel 2
Einfhrung in Multisim
6.
Drcken Sie whrend der Simulation die Taste <E>, um den Zhler zu aktivieren oder zu deaktivieren. Der Aktivierungseingang ist low-aktiv. Mit <L> wird der Zhler auf Null gestellt. Der Rckstelleingang ist ebenfalls low-aktiv. Drcken Sie <Shift-A> und beobachten Sie, was beim Verringern des Potentiometerwerts geschieht. Wiederholen Sie das Ganze, aber drcken Sie diesmal <A>, um den Potentiometerwert zu erhhen.
Tipp Statt mit den oben genannten Tasten knnen Sie die Bauelemente auch mit der Maus
bedienen.
Analyse
In diesem Abschnitt fhren Sie an Ihrer Schaltung eine AC-Analyse durch, um den Frequenzgang des Verstrkers zu prfen. Zum Durchfhren einer AC-Analyse am Ausgang des Operationsverstrkers gehen Sie wie folgt vor: 1. Klicken Sie die Leiterbahn doppelt an, die zum Pin 6 des Operationsverstrkers fhrt, und ndern Sie ggf. den bevorzugten Netznamen im Dialogfeld Netzeinstellungen in analog_out. Whlen Sie SimulierenAnalysenAC-Analyse und klicken Sie auf die Registerkarte Ausgabe.
2.
2-14
ni.com
Kapitel 2
Einfhrung in Multisim
3.
Markieren Sie V(analog_out) in der linken Spalte und klicken Sie auf Hinzufgen. Der Eintrag V(analog_out) wird daraufhin in die rechte Spalte verschoben. Damit wird kenntlich gemacht, dass die Spannung am Knoten V(analog_out) nach der Simulation angezeigt wird.
2-15
Kapitel 2
Einfhrung in Multisim
4.
Klicken Sie auf Simulieren. Die Ergebnisse der Analyse werden in der Graphanzeige angezeigt.
Graphanzeige
In der Graphanzeige knnen Graphen und Tabellen angezeigt, bearbeitet, gespeichert und exportiert werden. In diesem Fenster werden die Ergebnisse aller Multisim-Analysen in Graphen und Diagrammen oder Kurvengraphen dargestellt (wie bei einem Oszillographen). Zur Anzeige der Simulationsergebnisse in der Graphanzeige gehen Sie wie folgt vor: 1. 2. Starten Sie die Simulation mit Hilfe des Oszillographen wie oben beschrieben. Whlen Sie AnsichtGraphanzeige.
2-16
ni.com
Kapitel 2
Einfhrung in Multisim
Postprozessor
Im Postprozessor knnen Sie mit Ihren Analyseergebnissen Berechnungen durchfhren oder die Ergebnisse grafisch darstellen. Auf die Ergebnisse knnen arithmetische, trigonometrische, logarithmische, komplexe und logische Operationen sowie Exponential- und Vektorfunktionen angewandt werden.
Berichte
In Multisim knnen Berichte unterschiedlichster Art erzeugt werden, z. B. Stcklisten (BOMs), Einzelheiten zu Bauelementen, Netzlisten, Schaltplanstatistiken, Listen unbelegter Gatter oder Querverweisberichte. In diesem Abschnitt soll fr den Beispielschaltplan eine Stckliste erstellt werden.
2-17
Kapitel 2
Einfhrung in Multisim
Stckliste
Eine Stckliste ist eine Aufstellung der Bauelemente, die fr eine bestimmte Schaltung und die Herstellung der zugehrigen Leiterplatte verwendet werden. Sie enthlt folgende Angaben: Stckzahl der bentigten Bauelemente Beschreibung jedes Bauelements einschlielich des Bauelementtyps (z. B. Widerstand) und des Werts (z. B. 5,1 kOhm) Referenzbezeichner jedes Bauelements Gehuse oder Footprint jedes Bauelements
Zum Erstellen einer Stckliste zu Ihrer Schaltung gehen Sie wie folgt vor: 1. Whlen Sie BerichteStckliste. Nun wird die Stckliste geffnet, die in etwa wie folgt aussieht:
Zum Drucken der Stckliste klicken Sie auf die Schaltflche Drucken. Daraufhin ffnet sich das Windows-Druckdialogfeld, in dem Sie den gewnschten Drucker, die Anzahl der Kopien usw. auswhlen knnen. Klicken Sie zum Speichern der Stckliste auf die Schaltflche Speichern. Daraufhin ffnet sich das Windows-Dialogfeld zum Speichern von Dateien, in dem Sie den Pfad und den Dateinamen angeben knnen.
2-18
ni.com
Kapitel 2
Einfhrung in Multisim
Da die Stckliste hauptschlich zur Untersttzung bei der Beschaffung und Herstellung gedacht ist, enthlt sie keine Bauelemente, die nicht real sind oder nicht beschafft werden knnen, wie z. B. Quellen oder virtuelle Bauelemente. Bauelemente, denen kein Footprint zugewiesen ist, erscheinen nicht in der Stckliste. Wenn Sie eine Liste der Bauelemente in Ihrer Schaltung sehen mchten, bei denen es sich nicht um reale Bauelemente handelt, klicken Sie auf die Schaltflche Virtuelle Bauelemente anzeigen. Daraufhin wird ein weiteres Fenster geffnet, in dem nur diese Bauelemente angezeigt werden. Weitere Informationen zu Stcklisten und anderen Berichtarten finden Sie in der Multisim Help.
2-19
Einfhrung in Ultiboard
In diesem Kapitel wird die praktische Erstellung von Leiterplatten anhand der im Kapitel 2, Einfhrung in Multisim, beschriebenen Schaltplne erlutert. In Ihrer Ultiboard-Edition sind mglicherweise nicht alle der in diesem Kapitel beschriebenen Funktionen vorhanden. Der Funktionsumfang Ihrer Edition ist in den Versionshinweisen zur NI Circuit Design Suite beschrieben.
Ultiboard-Benutzeroberflche
Ultiboard ist das Programm der NI Circuit Design Suite, mit dem das Layout von Leiterplatten entwickelt wird. Die Circuit Design Suite von National Instruments ist ein Softwarepaket zur automatisierten Elektronik-Entwicklung, die Ihnen die wichtigsten Schritte in der Schaltungsentwicklung erleichtert. Ultiboard erzeugt anhand der Daten von Multisim gedruckte Schaltungen, fhrt einfache mechanische CAD-Arbeitsschritte durch (z. B. Platzierung der Bauelemente auf den Leiterplatten) und bereitet die Leiterplatten fr die Produktion vor. Auerdem bietet das Programm automatisierte Funktionen fr Bestckung und Verbindungen.
3-1
Kapitel 3
Einfhrung in Ultiboard
1 2 3 4 5
6 7 8 9
10 11 12 13
Die Menleiste enthlt die Befehle fr smtliche Funktionen. Die Symbolleiste Standard enthlt Schaltflchen fr die meistverwendeten Funktionen wie Speichern, Drucken, Ausschneiden oder Einfgen. Je mehr Bauelemente und Leiterbahnen Sie einer Leiterplatte hinzufgen, desto schwieriger wird es, ein bestimmtes Objekt zu markieren. Die Symbolleiste Auswahl enthlt Schaltflchen, die das Markieren von Objekten vereinfachen sollen.
3-2
ni.com
Kapitel 3
Einfhrung in Ultiboard
Die Symbolleiste Zeicheneinstellungen ermglicht Ihnen die Auswahl der Lage, Dicke und Messgre gezeichneter Linien oder Objekte. Auerdem bietet sie Schaltflchen fr Funktionen, mit denen die Darstellung von Linien und Formen auf einer Lage gendert werden kann. Die Symbolleiste Ansicht enthlt Schaltflchen zum ndern der Bildschirmanzeige. Die Hauptleiste enthlt Schaltflchen fr allgemeine Leiterplattenfunktionen. Die Symbolleiste Automatische Leiterbahnfhrung enthlt Funktionen zum Autorouting und zur Bauelementplatzierung. Die Statusleiste zeigt wichtige Informationen an. Der Arbeitsbereich enthlt Ihre Schaltung. Mit der Tabellenansicht knnen Sie Angaben zu Bauelementen abfragen und ndern, z. B. Platzbedarf, Referenzbezeichnung, Attribute oder Beschrnkungen. Unter Schaltungswerkzeuge knnen Sie Teile der Schaltung ein- und ausblenden oder abdunkeln. Mit der 3D-Vorschau erhalten Sie eine dreidimensionale Vorschau der Leiterplatte. Mit Vogelperspektive wird die Schaltung zur besseren bersicht bildschirmfllend angezeigt.
Tipp Das Importieren von Multisim-Schaltplnen ist in der Multisim Help und der
3-3
Kapitel 3
Einfhrung in Ultiboard
4.
Zum Auswhlen eines Schaltplans aus dem Projekt (z. B. GS1) klicken Sie entweder auf die dazugehrige Registerkarte oder whlen Sie auf der Registerkarte Projekte der Schaltungswerkzeuge den Namen des Schaltplans aus.
3-4
ni.com
Kapitel 3
Einfhrung in Ultiboard
Um mit dem Leiterplattenassistenten zu arbeiten, fhren Sie die folgenden Schritte aus: 1. 2. 3. Klicken Sie auf der Registerkarte Lagen doppelt auf Leiterplattenumriss. Klicken Sie in der Schaltung GS1 auf die vorhandene Kontur und drcken Sie die Taste <Entf>. Whlen Sie ExtrasLeiterplattenassistent.
4. 5.
Aktivieren Sie die Option Lagentechnologie ndern, um zu den Technologie-Optionen zu gelangen. Whlen Sie Mehrere Lagen mit doppelseitigen Leiterplatten und Einzellagenstapeln aus und klicken Sie auf Weiter.
3-5
Kapitel 3
Einfhrung in Ultiboard
Im nachfolgenden Dialogfeld knnen Sie berschichtungseinstellungen fr die Leiterplatte vornehmen. Bei dieser bung wird jedoch keine Einstellung gendert.
6.
Klicken Sie auf Weiter. Im Dialogfeld Leiterplattenassistent - Leiterplattenform: muss der Bezugspunkt zur Ausrichtung auf Unten links gesetzt sein. muss fr Form und Gre der Leiterplatte die Option Rechteckig ausgewhlt sein. muss die Breite auf 3000 und die Hhe auf 2000 eingestellt werden (diese Gre ist fr die Bauelemente in diesem Schaltplan besser geeignet). muss der Freiraum 5,00000 lauten. Dieser Wert gibt die Breite des freizuhaltenden Leiterplattenrands an.
7.
Klicken Sie auf Fertigstellen. Der Leiterplattenumriss wird Ihrer Schaltung hinzugefgt.
3-6
ni.com
Kapitel 3
Einfhrung in Ultiboard
Hinweis Weitere Einzelheiten zum Leiterplattenassistenten erhalten Sie in der Ultiboard Help.
Um den Leiterplattenumriss zu verschieben, fhren Sie die folgenden Schritte aus: 1. 2. Klicken Sie auf der Registerkarte Lagen doppelt auf Leiterplattenumriss. Klicken Sie dann an einer beliebigen Stelle auf den Leiterplattenumriss und ziehen Sie die Leiterplatte direkt unter die Bauelemente.
Zum ndern des Bezugspunkts gehen Sie wie folgt vor: 1. 2. Whlen Sie SchaltungBezugspunkt festlegen. Damit wird der Bezugspunkt dem Cursor unterlegt. Fhren Sie den Cursor in die linke untere Ecke des Leiterplattenumrisses und fhren Sie zum Einfgen des Bezugspunkts einen Mausklick aus.
3-7
Kapitel 3
Einfhrung in Ultiboard
Tipp Mit EinfgenPlatzierung von Bauelementen aufheben knnen Sie alle nicht
fixierten Bauelemente von der Leiterplatte entfernen und sie noch einmal auf eine andere Weise einfgen.
Tipp Mit Hilfe der Funktion BearbeitenSuchen knnen Sie nach einem Bauelement
suchen. Diese Funktion arbeitet im Groen und Ganzen wie die Suchfunktion anderer Anwendungen. Zustzlich knnen Sie ein Bauelement jedoch auch nach Namen, Nummer, Form, Wert oder nach all diesen Parametern ausfindig machen. Weitere Informationen dazu finden Sie in der Ultiboard Help.
3-8
ni.com
Kapitel 3
Einfhrung in Ultiboard
2.
Klicken Sie auf U1 (die 7-Segment-Anzeige) und ziehen Sie sie an die in der unteren Abbildung gezeigte Position.
U1 bleibt so lange ausgewhlt, bis Sie die Markierung aufheben. In Ultiboard mssen Sie jeden Vorgang beenden, bevor Sie fortfahren knnen. In diesem Fall wird die Auswahl des Bauelements durch einen Klick an eine andere Stelle aufgehoben. Auch durch einen Klick mit der rechten Maustaste kann der aktuelle Vorgang beendet werden. 3. Klicken Sie auf die Registerkarte Bauelemente in der Tabellenansicht und scrollen Sie zu U1. Sie werden feststellen, dass die grne LED neben dem Bauelement etwas heller leuchtet dadurch wird angezeigt, dass das Bauelement bereits auf der Leiterplatte platziert wurde.
3-9
Kapitel 3
Einfhrung in Ultiboard
2.
Klicken Sie auf J3 und ziehen Sie das Element von der Registerkarte Bauelemente in den Arbeitsbereich. J3 ist nun dem Mauszeiger unterlegt. Legen Sie J3 links am Rand etwa mittig auf der Leiterplatte ab. Wie bereits zuvor beobachtet, leuchtet nun auch die grne LED von J3 auf der Registerkarte Bauelemente etwas heller und zeigt damit an, dass das Bauelement auf der Leiterplatte platziert wurde.
3.
3-10
ni.com
Kapitel 3
Einfhrung in Ultiboard
3-11
Kapitel 3
Einfhrung in Ultiboard
3.
Klicken Sie unter Verfgbare Bauelemente auf Hole35. Die Komponente wird daraufhin in der Vorschau angezeigt.
4.
Klicken Sie auf OK. Das Dialogfeld Bauelement aus Datenbank abrufen wird ausgeblendet und Sie werden dazu aufgefordert, einen Referenzbezeichner (RefBez) und einen Wert einzugeben. Geben Sie als Referenzbezeichner des Bohrlochs H1 und als Wert HOLE ein und klicken Sie auf OK. Bewegen Sie den Mauszeiger ber die Leiterplatte. Die Komponente ist nun dem Mauszeiger unterlegt. Sobald sich das Loch im Bereich der oberen linken Ecke befindet, legen Sie es durch einen Mausklick auf der Leiterplatte ab. Es erscheint erneut das Dialogfeld Referenzbezeichnung fr Bauelement eingeben. Der Referenzbezeichner wird automatisch auf H2 erhht. Geben Sie den Wert HOLE ein und klicken Sie auf OK, um die nchste Bohrung in der rechten oberen Ecke zu platzieren und fahren Sie so mit H3 in der rechten unteren Ecke und H4 in der linken unteren Ecke fort.
5. 6. 7. 8.
9.
10. Klicken Sie zum Beenden des Vorgangs auf Abbrechen und schlieen Sie das Dialogfeld Bauelement aus Datenbank abrufen, indem Sie nochmals auf Abbrechen klicken.
3-12
ni.com
Kapitel 3
Einfhrung in Ultiboard
Markieren eines Bauelements auf der Leiterplatte mssen Sie daher aufpassen, dass Sie das gesamte Bauelement markieren und nicht nur die Beschriftung und die Ltaugen. Um diesen Vorgang zu erleichtern, knnen Sie die Auswahlfilter zu Hilfe nehmen. Weitere Informationen finden Sie in der Ultiboard Help.
Tipp Zum Verschieben eines Bauelements markieren Sie es und drcken Sie die Pfeil-
3-13
Kapitel 3
Einfhrung in Ultiboard
Sie knnen aber auch mehrere Bauelemente markieren und gemeinsam verschieben. Dazu gibt es folgende Mglichkeiten: Drcken Sie die <Shift>-Taste und klicken Sie mehrere Bauelemente an. Ziehen Sie um mehrere Bauelemente einen Rahmen auf.
Alle markierten Bauelemente werden beim Bewegen des Cursors gemeinsam verschoben.
Tipp Die Gruppen gelten jedoch nur vorbergehend sobald Sie ein anderes Bauelement
auswhlen, geht die Gruppierung verloren. Um eine Gruppe von Bauelementen dauerhaft (bis zum Entfernen) zusammenzuhalten, ist der Gruppeneditor zu verwenden. Weitere Informationen finden Sie in der Ultiboard Help. Durch BearbeitenAusrichten knnen markierte Bauelemente so verschoben werden, dass ihre Rnder in einer Linie sind oder die Bauelemente einen bestimmten Abstand voneinander haben. So platzieren Sie das eingefgte Bohrloch durch BearbeitenAusrichten an die richtige Stelle: 1. 2. Whlen Sie H1 und halten Sie fr H2 die <Shift>-Taste gedrckt. Whlen Sie BearbeitenAusrichtenOben ausrichten. Wenn H2 nicht in Linie mit H2 eingefgt wurde, wird es nun entsprechend verschoben. Klicken Sie auf einen freien Bereich auf der Leiterplatte und markieren Sie H2 und H3. Whlen Sie BearbeitenAusrichtenRechts ausrichten. Fahren Sie auf diese Weise mit dem Ausrichten der Unterkanten von H3 und H4 sowie der linken Kanten von H1 und H4 fort.
3. 4. 5.
Eine manuell eingefgte Leiterbahn wird genau so verlegt, wie Sie es vorgeben, auch wenn sie durch ein Hindernis verluft. Eine Follow-me-
3-14
ni.com
Kapitel 3
Einfhrung in Ultiboard
Leiterbahn stellt selbstndig zulssige Verbindungen zwischen den mit der Maus ausgewhlten Pins her. Sie knnen die Maus also von Pin zu Pin bewegen und so eine Leiterbahn anlegen. Beim vollautomatischen Einfgen von Leiterbahnen werden zwei Pins auf dem krzestmglichen Weg miteinander verbunden, wobei der Verlauf der Leiterbahn nachtrglich von Hand gendert werden kann. Bevor Sie mit der Maus klicken, um eine Leiterbahn an einer bestimmten Stelle zu fixieren, knnen Sie jederzeit ein Stck der Leiterbahn entfernen, indem Sie den Cursor zurckbewegen. Ein neues Segment wird immer dann erzeugt, wenn Sie durch Mausklicks eine Leiterbahn manuell verlegen oder wenn eine (halb-)automatisch verlegte Leiterbahn die Richtung ndert. Dieser Umstand ist bei nderungen an Leiterbahnen zu bercksichtigen.
Zum manuellen Verlegen einer Leiterbahn gehen Sie wie folgt vor: 1. Whlen Sie EinfgenLinie.
Tipp Mit dem Menpunkt Linie wird auf einer beliebigen Lage eine Linie erzeugt. Die
Art der Linie ist je nach ausgewhlter Lage unterschiedlich. Wenn die ausgewhlte Lage zum Beispiel die Siebdrucklage ist, wird damit auf der Siebdrucklage eine Linie erzeugt. Bei einer Kupferlage wird mit dieser Option eine leitende Verbindung hergestellt.
3-15
Kapitel 3
Einfhrung in Ultiboard
2.
Suchen Sie links auf der Leiterplatte nach J3. Finden Sie heraus, wo sich der unten gezeigte Startpin befindet:
Bauelement J3
Startpin
Tipp Die Kraftvektoren knnen ausgeblendet werden, so dass die Netze deutlicher sicht-
bar sind. Deaktivieren Sie dazu die Option Kraftvektoren auf der Registerkarte Lagen der Schaltungswerkzeuge. Weitere Informationen zu Kraftvektoren finden Sie in der Ultiboard Help.
Tipp Bei Schwierigkeiten mit dem Auffinden des Bauelements nutzen Sie die Suchfunk-
tion auf der Registerkarte Bauelemente. Whlen Sie das Bauelement auf der Registerkarte Bauelemente aus und klicken Sie dann die Schaltflche Bauelement suchen und auswhlen an. Das Bauelement wird im Arbeitsbereich angezeigt. Bei Bedarf knnen Sie mit Hilfe des Mausrads nher heranzoomen.
3-16
ni.com
Kapitel 3
Einfhrung in Ultiboard
3.
Klicken Sie auf den Pin, der im Schritt oben festgelegt wurde. Ultiboard hebt daraufhin alle Pins hervor, die zum selben Netz gehren. Die Hervorhebungsfarbe kann auf der Registerkarte Farben des Dialogfelds Einstellungen gendert werden. So wissen Sie, welche Pins Ihrem Schaltplan entsprechend zu verbinden sind.
4.
Bewegen Sie den Cursor in eine beliebige Richtung. Eine grne Linie (die Leiterbahn) wird nun an den ausgewhlten Pin angefgt. Mit jedem Klick fixieren Sie ein Leiterbahnensegment, wie in der folgenden Abbildung dargestellt. Klicken Sie auf den Pin, an dem die Verbindung enden soll.
5.
1 2
Endpunkt
3-17
Kapitel 3
Einfhrung in Ultiboard
6. 7.
Mit einem Rechtsklick und Auswahl von Abbrechen wird das Verlegen von Leiterbahnen beendet. Um den Modus zum Verlegen von Leiterbahnen zu beenden, klicken Sie in der Hauptleiste auf die Schaltflche Markieren.
Tipp Anstelle der Pins knnen Sie auch die Luftlinienverbindung zwischen den Bauele-
menten anklicken.
3-18
ni.com
Kapitel 3
Einfhrung in Ultiboard
Luftlinie anklicken
3.
Beim Bewegen Ihres Cursors schlgt Ultiboard automatisch verschiedene Leiterbahnverlufe um Hindernisse herum vor.
3-19
Kapitel 3
Einfhrung in Ultiboard
4.
Wenn Sie sich fr eine Leiterbahnfhrung entschieden haben, fixieren Sie die Leiterbahn durch einen Klick. Sie mssen dazu nicht auf die Luftlinie oder den Pin klicken, an dem die Verbindung enden soll.
5.
Automatische Bestckung
Neben den bisher beschriebenen Mglichkeiten zum Bestcken von Leiterplatten bietet Ultiboard eine vollautomatische BauelementPlatzierungsfunktion fr fortgeschrittene Benutzer.
Tipp Vor dem automatischen Bestcken der Leiterplatte mssen Sie alle Bauelemente, die
vom automatischen Einfgen nicht betroffen sein sollen, per Hand einfgen und an der gewnschten Stelle fixieren. (Die Montagebohrungen und U1, J1, J2, J3, und LED 1 in GS5
3-20
ni.com
Kapitel 3
Einfhrung in Ultiboard
wurden beispielsweise bereits fixiert). Weitere Informationen zum Fixieren von Bauelementen finden Sie in der Ultiboard Help. Zum automatischen Einfgen der Bauelemente in Getting Started.ewprj, gehen Sie wie folgt vor: 1. 2. ffnen Sie die Schaltung GS5 in Ultiboard. Whlen Sie Automatische LeiterbahnfhrungAutomatische Bestckung starten. Die Leiterplatte wird nun mit den Bauelementen bestckt.
Automatische Leiterbahnfhrung
Leiterbahnen knnen in Ultiboard entweder nach den bisher beschriebenen Verfahren oder automatisch verlegt werden. Die automatische Leiterbahnfhrung wird nachfolgend erklrt. Zum automatischen Verbinden der Leiterbahnen in der Datei Getting
Started.ewprj gehen Sie wie folgt vor:
1. 2.
ffnen Sie in Ultiboard die Schaltung GS3. Whlen Sie Automatische LeiterbahnfhrungAutomatische Leiterbahnfhrung starten/fortsetzen. Der Arbeitsbereich wechselt in den Modus der automatischen Leiterbahnfhrung. Daraufhin knnen Sie sehen, wie die Leiterbahnen auf der Leiterplatte verlegt werden. Nach Abschluss des Vorgangs wechselt Ultiboard zurck zum Arbeitsbereich.
3-21
Kapitel 3
Einfhrung in Ultiboard
3.
Bei Bedarf knnen Sie den Verlauf der Leiterbahnen optimieren, indem Sie Automatische LeiterbahnfhrungOptimierung starten auswhlen.
Sie knnen die automatische Leiterbahnfhrung jederzeit anhalten und manuelle nderungen vornehmen. Bei erneutem Start der automatischen Leiterbahnfhrung fhrt die Funktion an der letzten Stelle fort. Alle manuell verlegten Leiterbahnen mssen fixiert werden, damit sie nicht durch die Automatik verschoben werden.
Tipp Die Einstellungen zum automatischen Bestcken mit Bauelementen und zur auto-
matischen Leiterbahnfhrung befinden sich in den Leiterbahnfhrungsoptionen. Weitere Informationen dazu finden Sie in der Ultiboard Help.
3-22
ni.com
Kapitel 3
Einfhrung in Ultiboard
3-23
Kapitel 3
Einfhrung in Ultiboard
Tipp Die Innenansicht ermglicht Ihnen einen Blick zwischen die Lagen einer mehrla-
3-24
ni.com
In diesem Kapitel wird die Simulation einer Schaltung mit Mikrocontroller und die Fehlersuche in einer solchen Schaltung beschrieben. Einige der hier genannten Funktionen sind mglicherweise nicht in Ihrer Version der Circuit Design Suite verfgbar. Der Funktionsumfang Ihrer Edition ist in den Versionshinweisen zur NI Circuit Design Suite beschrieben.
berblick
Die fr diese Einfhrung verwendeten Dateien werden zusammen mit der NI Circuit Design Suite Software unter ...\Dokumente und Einstellungen\All Users\Gemeinsame Dokumente\National Instruments\Circuit Design Suite 11.0\samples\Getting Started installiert.
Fr diese Anleitung nutzen Sie die Datei Getting Started MCU.ms11, die bei Bedarf auf den Inhalt des Ordners LCDWorkspace zugreift. Im Multisim-Schaltungsbeispiel fr eine LCD-Grafikanzeige wird der Einsatz eines PIC-Mikrocontrollers zur Steuerung der Anzeige anhand eines Toshiba-T6963C-Controllers und einem externen RAM-Speichers demonstriert. Zur Steuerung der Anzeige bermittelt der Mikrocontroller Signale ber die Daten- und Steuerleitungen des Gerts. Ein fr den Mikrocontroller entwickeltes Softwareprogramm bestimmt die Pin-Logikpegel (High oder Low), mit deren Hilfe Befehle und Daten an die Anzeige bermittelt werden.
4-1
Kapitel 4
Kapitel 4
Zum ffnen der Datei gehen Sie wie folgt vor: 1. Klicken Sie unter Schaltungswerkzeuge doppelt auf main.asm. Im Arbeitsbereich erscheint daraufhin eine Registerkarte mit dem Namen main.asm, auf der das Assembler-Programm angezeigt wird.
Zum Einblenden der Zeilennummern whlen Sie MCUZeilennummern anzeigen. Zum Ausfhren der Schaltung gehen Sie wie folgt vor: 1. Whlen Sie SimulierenStart. Wenn Sie noch keine Programmdatei erzeugt haben, wird ein Dialogfeld mit dem Hinweis angezeigt, dass die Konfiguration nicht mehr aktuell ist. Sie werden daher zum Erstellen einer Programmdatei aufgefordert. Klicken Sie auf Ja. Die Ergebnisse des Build-Prozesses werden in der Tabellenansicht auf der Registerkarte Ergebnisse angezeigt. Gehen Sie zur Schaltung zurck. Das Programm zeigt die Zeile Graphical LCD T6963C for Multisim im Textmodus an; das LCD schaltet dann in den Grafikmodus um und stellt Punkt fr Punkt ber dem Text ein umgedrehtes V dar. Nach der Anzeige der Linien scrollt der Text nach rechts und links. Dazu wird einfach die Startadresse des Textpuffers der LCD-Anzeige verschoben. Die Anzeige enthlt zwei Pufferspeicher, und zwar einen zum Speichern von Grafiken und einen zum Speichern von Texten. Weitere Funktionen der LCD-Anzeige, wie Blinken des Textes und Lschen von Zeichen, werden ebenfalls demonstriert. Das Programm zur Steuerung der LCD-Anzeige stellt jeden dieser Effekte nacheinander dar. Um die Simulation anzuhalten, whlen Sie SimulierenStopp.
4-3
Kapitel 4
Der anzuzeigende Text wird bei einigen Mikrocontrollern in Form einer Tabelle gespeichert. Es gibt aber keinen Assembler-Befehl, um direkt auf einen Datenwert im Speicherbereich des Programms zuzugreifen. Stattdessen besteht die Mglichkeit, Werte uncodiert in das W-Register zu laden. So knnen Sie eine Routine schreiben, die je nach Kennzahl einen anderen String ausgibt. Die RETLW-Anweisung ldt einen konstanten Wert in das W-Register und fhrt einen RETURN durch (beides in einem Befehl).
4-4
ni.com
Kapitel 4
Die TXPRT-Routine fragt den auf der LCD-Anzeige darzustellenden Text ab. Die Zeichencodes der LCD-Anzeige sind im Handbuch zum T6963C-Controller festgehalten (z. B. 0x27 steht fr G und 0x52 fr r).
4-5
Kapitel 4
Initialisierung Der Initialisierungscode beginnt bei START, wie im Programmabschnitt unten dargestellt. Die Pins des Mikrocontrollers werden als Ausgangskontakte konfiguriert und die Werte zurckgesetzt. Die LCD-Anzeige wird durch den Mikrocontroller initialisiert und auf Grafik- und Textmodus gestellt. Die Rcksprungadresse wird fr den Grafikpuffer auf 0x0000 und den Textpuffer auf 0x2941 eingestellt. Dadurch wird festgelegt, an welcher Stelle im LCD die Anzeige die Daten beginnen soll. Schlielich werden die Steuersignale noch fr den geeigneten Schreib-/Lesezugriff auf der LCD-Anzeige eingestellt.
4-6
ni.com
Kapitel 4
Darstellen von Text und Grafiken Der Rest des Programmcodes dient dazu, Befehle ber die Steuerleitungen und die Mikrocontroller-Pins (RA0 bis RA2) an die LCD-Anzeige zu bermitteln und die Daten ber die Datenleitungen zu senden:
Zum Beispiel werden mit dem oben dargestellten Programmabschnitt die mit der TXPRT-Subroutine angegebenen Zeichen aus der Hauptschleife an die im Textmodus befindliche LCD-Anzeige bertragen. Mit den folgenden Befehlen wird die LCD-Anzeige in den Auto-Schreibmodus umgeschaltet:
MOVLW MOVWF CALL CMD_AWRON CMD_BUFFER CMD
4-7
Kapitel 4
An diesem Punkt beginnt das Programm zu zhlen und fhrt die Schleife LOOP_READ_DATA2 35 Mal aus. Durch TXPRT ruft die Schleife den Text ab und ldt ihn in das W-Register. Dann ruft sie die Subroutine ADT auf, welche wiederum SEND_DATA aufruft. Dadurch werden die Werte im W-Register an den Anschluss B gesendet, so dass sie an die Datenleitungen der LCD-Anzeige bermittelt werden knnen. Nach dem Senden der Daten wird der Eigenwert von Anschluss A des Mikrocontrollers an die Steuerkontakte der LCD-Anzeige bertragen, um zu signalisieren, dass die Daten gelesen werden knnen. Nach Ausfhrung jeder Subroutine kehrt das Programm wieder an das Ende des letzten Befehls zurck, der vor dem Aufruf der Subroutine ausgefhrt wurde. Das passiert so lange, bis alle 35 Zeichen bermittelt wurden. Mit den letzten drei Anweisungen wird nach Verlassen der Schleife der Auto-Schreibmodus der LCD-Anzeige ausgeschaltet:
MOVLW MOVWF CALL CMD_AWROFF CMD_BUFFER CMD
Mit den folgenden Anweisungen wird die horizontale und die schrge Linie im Grafikmodus gezeichnet:
;6 draw wave once MOVF BTFSC CALL ADDR_L, 0 STATUS, Z DRAW_WAVE
MCU-Fehlersuchfunktionen
Dieser Abschnitt enthlt eine Schritt-fr-Schritt-Beschreibung der Multisim-Fehlersuchfunktion fr MCUs. Es ist wichtig, dass die Schritte genau in der angegebenen Reihenfolge ausgefhrt werden. Sobald Sie mit der Haltepunktfunktion und dem Einzelschrittverfahren vertraut sind, knnen Sie sich mit den komplexeren Fehlersuchfunktionen befassen.
4-8
ni.com
Kapitel 4
Um zur Quellcodeansicht zu gelangen, gehen Sie wie folgt vor: 1. Fhren Sie in den Schaltungswerkzeugen in der Hierarchie der MCU-Arbeitsbereiche einen Doppelklick auf die Datei aus (z. B. main.asm).
Die whrend der Simulation angezeigten zustzlichen Fehlersuchinformationen sollen Ihnen einen Einblick in die Vorgnge innerhalb der MCU verschaffen. Sie knnen beispielsweise zwischen dem High-Level-Quellcode und den Assembler-Anweisungen umschalten, die auerdem den tatschlichen Opcode fr jede ausgefhrte Anweisung enthalten. In der Quellcodeansicht knnen all diese Zusatzinformationen nicht angezeigt werden. Stattdessen hat jedes MCU-Bauelement im Schaltplan eine eigene Debug-Ansicht, in der Angaben zu Fehlern angezeigt werden. Um zur Debug-Ansicht zu gelangen, gehen Sie wie folgt vor: 1.
Hinweis
Die Debug-Ansicht ist nur dann verfgbar, wenn Sie Ihren Code erfolgreich erstellt haben, so dass der vorherige Schritt nur einmal notwendig ist. 2. Whlen Sie MCUMCU PIC 16F84A U1Debug-Ansicht. oder Klicken Sie im MCU-Arbeitsbereich der Schaltungswerkzeuge einen Eintrag mit der rechten Maustaste an und whlen Sie den entsprechenden Menpunkt aus.
4-9
Kapitel 4
Im Arbeitsbereich ffnet sich daraufhin eine weitere Registerkarte mit dem Namen Debug(<MCU-Referenzbezeichner>), in diesem Fall Debug(U1).
Dropdown-Liste
Whlen Sie im oberen Teil der Debug-Ansicht zwischen den in Multisim erzeugten Disassembler-Anweisungen und der im Assembler/Compiler erzeugten Auflistungsdatei aus (das Format der Auflistungsdatei richtet sich nach dem Tool, mit dem Sie die Programmdatei erzeugt haben). Im Beispiel der LCD-Grafikanzeige wurde der Programmcode in Assembler geschrieben und mit Hilfe der Mikrochip-Assembler-Tools in eine Programmdatei umgewandelt. Der Mikrochip-Assembler erzeugt eine Auflistungsdatei (*.Ist) mit den Opcodes zu jeder Assembler-Anweisung. In der Fehlerlistenansicht werden Informationen aus dieser Auflistungsdatei angezeigt. Multisim wandelt die Opcode-Anweisungen mit Hilfe eines internen Disassemblers in Assembler-Anweisungen um. Fr dieses Beispiel ist das Disassembler-Format jedoch nicht notwendig, da die Fehlerliste bereits alle erforderlichen Angaben enthlt. In den Fllen, wo ein MCU-Projekt nur die *.hex-Datei mit dem Maschinencode ldt, werden in der Disassembler-Ansicht die aufgeschlsselten Opcode-Anweisungen angezeigt. Auf diese Weise wird erkennbar, was innerhalb der MCU vor sich geht. Die Disassembler-Ansicht ist sehr ntzlich, da fr MCU-Projekte dieses Typs keine Auflistungsdatei verfgbar ist.
4-10
ni.com
Kapitel 4
Sie knnen aber auch einen Haltepunkt in der Debug-Ansicht angeben. Sie knnen Haltepunkte in der Disassembler-Ansicht oder der Fehlerlistenansicht einfgen. In diesem Beispiel bentigen Sie jedoch lediglich die Fehlerliste.
Graue Spalte
Um einen Haltepunkt in der Quellcodeansicht hinzuzufgen, gehen Sie wie folgt vor: 1. 2. 3. ffnen Sie Debug-Ansicht fr U1. Klicken Sie unter Schaltungswerkzeuge doppelt auf main.asm. Scrollen Sie bis zur Zeile unterhalb der START-Beschriftung: BCF
STATUS, RP0.
4-11
Kapitel 4
4.
Klicken Sie im Fenster main.asm die erste (graue) Spalte links neben BCF STATUS, RP0 doppelt an. Ein roter Punkt an dieser Stelle signalisiert, dass an dieser Zeile ein Haltepunkt gesetzt wurde. Whlen Sie SimulierenStart. Die Simulation wird nun automatisch an der Stelle unterbrochen, an der Sie den Haltepunkt gesetzt haben. Die Debug-Ansicht ffnet sich automatisch und ein gelber Pfeil zeigt auf die Stelle, wo die Programmausfhrung unterbrochen wurde.
5.
Zum Entfernen des Haltepunkts gehen Sie wie folgt vor: 1. Klicken Sie einen Haltepunkt in der Debug-Ansicht oder der Quellcodeansicht main.asm doppelt an. oder Whlen Sie MCUAlle Haltepunkte entfernen, um alle Haltepunkte zu entfernen.
Hinweis
Haltepunkte in der Debug-Ansicht werden genauso hinzugefgt und entfernt wie in der Quellcodeansicht.
3. 4.
4-12
ni.com
Kapitel 4
5.
Whlen Sie MCUMCU PIC16F84A U1Speicheransicht, um den aktuellen Status des Speichers im Mikrocontroller U1 anzuzeigen. Beachten Sie, dass der Wert des Programmzhlers PC des IROM-Abschnitts um eins hher liegt als der Adresswert der Zeile, auf die der gelbe Pfeil zeigt. (Im Beispiel in der Abbildung oben hat die Adresse in der Debug-Ansicht den Wert 192 und der PC-Wert in der Speicheransicht lautet 193).
Hinweis
Wenn der aktuelle Befehl bei Unterbrechung der Simulation noch nicht vollstndig ausgefhrt wurde, bleibt der Wert des Programmzhlers der gleiche wie der Adresswert. Die anderen Abschnitte der Speicheransicht enthalten Werte in anderen Teilen des Mikrocontroller-Speichers. 6. 7. 8. Klicken Sie in der Symbolleiste Simulation auf die Schaltflche In Funktion reinspringen. Die aktuelle Anweisung wird ausgefhrt und die Simulation bei der nchsten Anweisung unterbrochen. Whlen Sie SimulierenStopp.
4-13
Kapitel 4
4.
2.
Zum Cursor
1. 2. Whlen Sie MCUAlle Haltepunkte entfernen. Klicken Sie auf eine Zeile in der SEND_DATA-Subroutine, denn diese Subroutine wird bekanntermaen nochmals aufgerufen, um Daten an die LCD-Anzeige zu bermitteln.
4-14
ni.com
Kapitel 4
3.
Klicken Sie in der Werkzeugleiste Simulation auf die Schaltflche Zum Cursor. Die Simulation wird bis zur Anweisung ausgefhrt, die Sie in der SEND_DATA-Subroutine angeklickt haben. Dann folgt eine Ausfhrungspause und neben die Zeile wird ein gelber Pfeil gesetzt.
4-15
Auf der Website ni.com/germany finden Sie umfassende Informationen ber die folgenden professionellen Serviceleistungen und den technischen Support von National Instruments: SupportTechnische Untersttzung erhalten Sie auf der Website ni.com/support/d in Form folgender Informationsquellen und Tools: Technische RessourcenDie Website ni.com/support/d bietet Ihnen Soforthilfe bei Fragen und Problemen. Auerdem finden Sie hier Treiber, Updates, eine umfassende Wissensdatenbank (KnowledgeBase), Bedienungsanleitungen, Anleitungen zur Problemlsung, Tausende Beispielprogramme, autodidaktische Kurse und Application Notes. Registrierte Nutzer knnen sich auch an den Diskussionsforen auf ni.com/forums (englisch) beteiligen. Jede im Forum eingereichte Frage wird garantiert beantwortet. Standard Service ProgramTeilnehmer dieses Programms knnen sich telefonisch oder per E-Mail direkt mit unseren Applikationsingenieuren in Verbindung setzen und jederzeit die Schulungseinheiten im Services Resource Center nutzen. Beim Erwerb eines Produkts von National Instruments sind Sie automatisch ein Jahr lang zur Teilnahme am Standard Service Program berechtigt. Danach ist die Mitgliedschaft kostenpflichtig. Welche Art der technischen Untersttzung es in Ihrer Nhe gibt, erfahren Sie unter ni.com/services/d oder bei einer unserer Niederlassungen (ni.com/contact). Schulung und ZertifizierungAuf ni.com/training finden Sie Lernhandbcher, virtuelle Schulungsrume, bungs-CDs und Informationen zu Lernprogrammen mit Abschlusszertifikat. Hier knnen Sie sich auch fr eine der weltweit angebotenen Software-Schulungen anmelden.
A-1
Anhang A
SystemintegrationWenn Sie aus Zeit- oder Personalmangel oder anderen Grnden bei der Fertigstellung eines Projekts in Verzug geraten, knnen Ihnen die Mitglieder des NI-Alliance-Programms weiterhelfen. Fr Informationen zu diesem Programm setzen Sie sich entweder telefonisch mit einer National-Instruments-Niederlassung in Ihrer Nhe in Verbindung oder besuchen Sie die Website ni.com/alliance.
Sollten Sie nach dem Besuch unserer Website ni.com noch Fragen haben, wenden Sie sich bitte an eine Niederlassung von National Instruments in Ihrer Nhe. Die Telefonnummern unserer Niederlassungen sind am Anfang dieses Handbuchs aufgefhrt. Auf die Websites der einzelnen Niederlassungen, auf denen Sie immer die aktuellen Kontaktinformationen, Telefonnummern des technischen Supports, E-Mail-Adressen sowie aktuelle Ereignisse und Veranstaltungen finden, gelangen Sie ber ni.com/niglobal.
A-2
ni.com
Stichwortverzeichnis
Zahlen
3D-Schaltungen in Ultiboard, 3-24 Einfhrung in Multisim (berblick), 2-3 Einfhrungen (Beschreibung), 1-1 Exportieren von Dateien aus Ultiboard, 3-23
A
Analyse, 2-14 Assembler-Programm, 4-4 Aufbau der Benutzeroberflche, 3-1 automatische Bestckung, 3-20 automatische Leiterbahnfhrung, 3-21
F
Fehlersuche (Hilfsmittel von National Instruments), A-1 Fehlersuche im MCU, 4-7 Fertigung, 3-22 Follow-me-Leiterbahn, 3-18
B
Bauelemente mit zwei Anschlssen direkt in eine Verbindung einfgen, 2-9 Beispiele (von National Instruments), A-1 Benutzeroberflche Elemente, 2-1 Berichte, 2-17 BOM, 2-18
G
Gertetreiber (von National Instruments), A-1 Graphanzeige, 2-16
H
Haltepunkt, 4-10 Hilfe technische Untersttzung, A-1
D
Diagnoseprogramme (von National Instruments), A-1 Dokumentation in diesem Handbuch verwendete Symbole und Darstellungen, v NI-Informationsquellen, A-1
I
in diesem Handbuch verwendete Symbole und Darstellungen, v
K
KnowledgeBase, A-1 Kommentare, 3-23
E
Einfgen von Bauelementen aus der Ultiboard-Datenbank, 3-11 Einfgen von Bauelementen in Multisim, 2-5 Einfgen von Bauelementen in Ultiboard, 3-8, 3-10
L
Leiterplatten-Clean-Up, 3-23 Leiterplattenumriss, 3-4
S-1
Stichwortverzeichnis
M
manuell eingefgte Leiterbahn, 3-15 MCU-Anleitung, 4-2 MCU-Fehlersuchfunktionen, 4-7
Training und Zertifizierung (von National Instruments), A-1 Treiber (von National Instruments), A-1
U O
ffnen der Ultiboard-Einfhrung, 3-3 ffnen von Multisim-Dateien, 2-4 Online-Informationsquellen, A-1 berblick (MCU-Einfhrung), 4-1 Unterbrechen und aus Funktion herausspringen, 4-13 Unterbrechen und Funktionsaufruf berspringen, 4-13 Unterbrechen und in Funktion hineinspringen, 4-13 Unterbrechen und in/aus Funktion hinein-/herausspringen, 4-11
P
Postprozessor, 2-17 Produkte, 1-1 Programmierbeispiele (von National Instruments), A-1
V
Verbinden der Bauelemente in Multisim, 2-10 Verlegen von Leiterbahnen in Ultiboard, 3-14 Verschieben von Bauelementen, 3-8, 3-10 Verschieben von Bauelementen in Ultiboard, 3-13 virtuelle Messinstrumente, 2-12 vollautomatische Leiterbahnverlegung, 3-19
S
Schaltungsentwicklung, 2-4 Simulation, 2-12 Software (von National Instruments), A-1 Speichern von Multisim-Dateien, 2-4 Stckliste, 2-18 Support und Serviceleistungen von NI, A-1 Support, technisch, A-1
Z
Zum Cursor, 4-13
T
technische Untersttzung und andere Serviceleistungen von National Instruments, A-1
S-2
ni.com
2010 8 374482E
www.ni.com/jp/support
105-0011 2-4-1 A 4F
972 3 6393737, 39 02 41309277, 91 80 41190000, 44 (0) 1635 523545, 1800 300 800, 43 662 457990-0, 31 (0) 348 433 466, 800 433 3488, 82 02 3451 3400, 1800 226 5886, 41 56 2005151, 46 (0) 8 587 895 00, 34 91 640 0085, 386 3 425 42 00, 662 278 6777, 886 02 2377 2222, 420 224 235 774, 86 21 5050 9800, 45 45 76 26 00, 49 89 7413130, 90 212 279 3031, 0800 553 322, 47 (0) 66 90 76 60, 358 (0) 9 725 72511, 01 57 66 24 24, 55 11 3262 3599, 32 (0) 2 757 0020, 48 22 328 90 10, 351 210 311 210, 1800 887710, 27 0 11 805 8197, 01 800 010 0793, 961 (0) 1 33 28 28, 7 495 783 6851 ni.com/jp Info Code feedback
NI NI NI NI NI 1 NI NI NI
National Instruments NI NI BSIM3 and BSIM4 are developed by the Device Research Group of the Department of Electrical Engineering and Computer Science, University of California, Berkeley and copyrighted by the University of California. The ASM51 cross assembler bundled with Multisim MCU is a copyrighted product of MetaLink Corp. (www.metaice.com). HI-TECH C Compiler for PIC10/12/16 MCUs (Lite Edition), MPASM Macro Assembler, MPLINK Object Linker, and MPLIB Object Librarian and related documentation and literature is reproduced and distributed by National Instruments Ireland Resource Ltd. under license from Microchip Technology Inc. All rights reserved by Microchip Technology Inc. MICROCHIP SOFTWARE OR FIRMWARE AND LITERATURE IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE SOFTWARE OR FIRMWARE OR THE USE OF OTHER DEALINGS IN THE SOFTWARE OR FIRMWARE. Anti-Grain Geometry - Version 2.4 Copyright (C) 20022004 Maxim Shemanarev (McSeem) Permission to copy, use, modify, sell and distribute this software is granted provided this copyright notice appears in all copies. This software is provided "as is" without express or implied warranty, and with no claim as to its suitability for any purpose.
Anti-Grain Geometry - Version 2.4 Copyright (C) 20022005 Maxim Shemanarev (McSeem) 1. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 2. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 3. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
LabVIEWNational InstrumentsNIni.comNational Instruments National Instruments Corporation National Instruments ni.com/trademarks Trademark Information Electronics Workbench, Multisim and Ultiboard are trademarks of National Instruments. Portions of this product obtained under license from Bartels Systems GmbH.
National Instruments / ( ) ni.com/patents patents.txt National Instruments Patent Notice Some portions of this product are protected under United States Patent No. 6,560,572.
ERC ERC
monospace
Multisim
Multisim .......................................................................................................2-1 ..............................................................................................................................................................2-3 ...................................................................................................................................2-4 ................................................................................................2-4 ................................................................................................2-5 ......................................................................................................................2-9 ...................................................................................................................................2-12 ...............................................................................................................................2-12 ............................................................................................................................................2-14 ...................................................................................................................................2-15 .......................................................................................................................................2-16 .....................................................................................................................................................2-16 .......................................................................................................................................2-17
Ultiboard
Ultiboard .....................................................................................................3-1 ..........................................................................................................................3-3 .........................................................................................................3-4 .......................................................................................................................................3-7 ...............................................3-7 ..................................................................................3-9 ..................................................................................3-9 ..................................................................................3-10 ......................................................................................................................3-12 ...............................................................................................................................3-13 ....................................................................................................3-13 ................................................................................................3-16 .......................................................................................3-16 ............................................................................................................................................3-17 .............................................................................................................3-18
vii
/ ........................................................................................................ 3-19 ........................................................................................... 3-19 ............................................................................................................ 3-19 ........................................................................................... 3-19 3D .......................................................................................................................... 3-20
Multisim MCU
............................................................................................................................................................. 4-1 ..................................................................................................................... 4-2 .................................................................................. 4-4 MCU ......................................................................................................... 4-7 ............................................................................................................ 4-7 ........................................................................................... 4-10 ........................................................................................................ 4-11 ........................................................................................................ 4-13 ........................................................................................................ 4-13 .................................................................................................... 4-13 ................................................................................................................. 4-13
viii
ni.com/jp
Multisim PCB
Multisim /
Multisim Multisim
Ultiboard Multisim
Multisim MCU
Multisim Help Ultiboard Help
1-1
Multisim
Multisim
Multisim Circuit Design Suite EDA Electronics Design Automation Multisim PCB
2-1
Multisim
Multisim
1 2 3 4 5
6 7 8 9
10 11 12 13
PCB Multisim
2-2
ni.com/jp
Multisim
Multisim
F1
2-3
Multisim
Multisim
1.
1. 2.
Windows MyGettingStarted
2-4
ni.com/jp
Multisim
1.
Multisim
1. 2.
MyGettingStarted.ms11 7 LED OK
seven_seg_decimal_com_a_blue
2-5
Multisim
3.
U1
4.
2-6
ni.com/jp
Multisim
RLC : : PCB
RLC
200 Ctrl-R
: U1U2
2-7
Multisim
5.
SPDT
6.
2-8
ni.com/jp
Multisim
7. 8.
AC (Pk) 0.2 V OK
9.
J3 Basic CONNECTORS
2 Multisim
2-9
Multisim
1.
2.
2 Multisim
2-10
ni.com/jp
Multisim
3.
U3 R4 Multisim Help
2-11
Multisim
4.
Multisim
Getting Started samples Getting Started 2.ms11
1.
J1J2R2
Multisim
3.
B A
4.
5.
7 LED
6.
E / LOW L LOW
2-13
Multisim
Shift-A A
AC AC
1.
6 analog_out AC
2.
2-14
ni.com/jp
Multisim
3.
4.
Multisim :
1. 2.
2-15
Multisim
2-16
ni.com/jp
Multisim
1.
: : 5.1 k)
BOM
Windows Windows
2-17
Multisim
Multisim Help
2-18
ni.com/jp
Ultiboard
Ultiboard
Ultiboard Circuit Design Suite PCB EDAElectronics Design Automation
3-1
Ultiboard
Ultiboard
1 2 3 4
5 6 7
8 9 10
11 12 3D 13
3-2
ni.com/jp
Ultiboard
3D 3
1.
National Instruments Circuit Design Suite 11.0 Ultiboard 11.0 Ultiboard Getting Started
Getting Started.ewprj
2. 3.
3-3
Ultiboard
4.
: GS1
DXF
3-4
ni.com/jp
Ultiboard
1. 2. 3.
GS1 Delete
4. 5.
3-5
Ultiboard
6.
7.
Ultiboard Help
1.
3-6
ni.com/jp
Ultiboard
2.
1. 2.
GS1
PCB
Multisim
3-7
Ultiboard
U1
1.
U1 U1
Ultiboard Help
2.
U17
U1 Ultiboard
3-8
ni.com/jp
Ultiboard
3.
U1
1.
J3
2. 3.
J3 J3 J3 J3
GS2
3-9
Ultiboard
1. 2.
3.
3-10
ni.com/jp
Ultiboard
4.
OK
5. 6. 7. 8. 9.
H1HOLEOK H2 HOLE OK H3 H4
10.
3-11
Ultiboard
Shift
3-12
ni.com/jp
Ultiboard
Ultiboard Help 1
1. 2. 3. 4. 5.
Shift H2 H1 H2 H1 H2 H2 H3 H3 H4 H1 H4
GS3
3-13
Ultiboard
F7
1.
PCB
2.
J3
J3
Ultiboard Help
3.
Ultiboard X
3-14
ni.com/jp
Ultiboard
4.
5.
1 2
6. 7.
3-15
Ultiboard
1. 2. 3. 4.
J3 U4 2 Ultiboard
1. 2.
3.
Ultiboard
3-16
ni.com/jp
Ultiboard
4.
5.
3-17
Ultiboard
Getting Started.ewprj
1. 2.
Ultiboard GS5
Ultiboard
Getting Started.ewprj
1. 2.
Ultiboard GS3
/
3.
3-18
ni.com/jp
Ultiboard
Ultiboard Help
/
Ultiboard
GS4
Ultiboard Help
3-19
Ultiboard
3D
Ultiboard 3 Ultiboard Help
3-20
ni.com/jp
Multisim MCU
NI Circuit Design Suite ...samplesGetting Started Getting Started MCU.ms11 LCDWorkspace LCDToshiba T6963C RAM Multisim LCD PIC LCD LCD LCD LCD HIGH LOW
4-1
Multisim MCU
4-2
ni.com/jp
Multisim MCU
main.asm 1 project1
1.
main.asm main.asm
MCU
1.
LCD
4-3
Multisim MCU
LCD
PIC W RETLW 1 W RETURN
4-4
ni.com/jp
Multisim MCU
4-5
Multisim MCU
LCD MCU RA0 RA2
4-6
ni.com/jp
Multisim MCU
;6 draw wave once MOVF BTFSC CALL ADDR_L, 0 STATUS, Z DRAW_WAVE
MCU
Multisim MCU MCU
C .asm.inc.c.h MCU
1.
MCU : main.asm
MCU MCU
4-7
Multisim MCU
MCU
1.
2.
MCU
4-8
ni.com/jp
Multisim MCU
Multisim
4-9
Multisim MCU
1 main.asm
MCU
1. 2. 3.
U1
main.asm
START BCF STATUS, RP0
4-10
ni.com/jp
Multisim MCU
4.
5.
1.
main.asm
MCU
1. 2. MCU
Getting Started MCU Graphical LCD T6963CC for Multisim LCD
3. 4.
U1 MCU
4-11
Multisim MCU
5.
MCU
6. 7. 8.
4-12
ni.com/jp
Multisim MCU
1. 2. 3. 4.
MOVWF PORTB SEND_DATA
1. 2. 3. 4. MCU
SEND_DATA SEND_DATA
1.
SEND_DATA SEND_DATA CALL SEND_DATA
2.
3.
SEND_DATA MCU
4-13
NI ni.com/jp ni.com/jp/support
ni.com/jp/training NI ni.com/jp/alliance
A-1
A-2
ni.com/jp
2
2-9
BOM2-17
MCU 4-2 MCU 4-1 MCU 4-7 MCU 4-7 Multisim 2-3 Multisim 2-9 Multisim 2-5 Multisim 2-4 Multisim 2-4
A-1
N U
A-1 A-1
NI A-1
Ultiboard DB 3-10 Ultiboard 3-19 Ultiboard 3-3 Ultiboard 3-12 Ultiboard 3-73-9 Ultiboard 3-13 Ultiboard 3D 3-20
2-15
NI A-1
3-19
3-7
4-4 2-16
I-1
A-1
A-1
NI A-1
3-4 3-19
1-1
2-1 3-16
2-16
I-2
ni.com/jp