Professional Documents
Culture Documents
FALK STEELFLEX
The simplest, most cost-effective coupling
ELASTOMER
$7,717 Total
DISC
$5,264 Total
GEAR
$2,895 Total
STEELFLEX
$2,390 Total
I
0
I
1,000
I
2,000
I
3,000
I
5,000
I
6,000
I
7,000
I
8,000
LOW CONTACT
PIVOTS
ROCKS
HEAVY LOAD
Equipment Protection
Against Shock/
Vibratory Loads
Torsional flexibility is the
ability of Falk Steelflex couplings to
torsionally deflect when subjected to
normal shock or vibratory loads,
providing flexible accommodation to
changing load conditions.
Consequently, Steelflex tunes the
drive system. It absorbs impact
energy by spreading it over an
I
4,000
FLOATS
CONTACT INCREASES
Versatile Designs
Two cover designs are available in
the popular sizes. Standard spacer,
piloted, high speed, brakewheel or
disc, and controlled torque designs
are also available.
Worldwide Availability
Steelflex couplings and component
parts, are available in popular sizes
and types. Our distribution centers
and worldwide distribution network
offer the largest stock of rough bore,
finish straight bore and Taper-lock
bushed hubs of any shaft coupling
on the market. Plus, Steelflex grid
couplings are warranted for 5 Years
when lubricated with Falk LTG Long
Term Grease.
High Ratings
Extended Maintenance Periods
Quick Installation
Easy Maintenance
Versatile Design
Availability
Protection Against Shaft Misalignment
Protection Against Shock Loads, Vibration & Thrust Loads
General Information
Falk standards apply unless otherwise specified.
All Dimensions are for reference only and are subject to change
without notice unless certified.
Unless otherwise specified, Falk coupling hub Sizes 1020 thru
1090 will be bored for CLEARANCE FIT with a setscrew OVER
the keyway. Sizes 1100 and larger will be furnished for
INTERFERENCE FIT without a setscrew (see Table 27, Page 43).
Recommended key sizes for the listed maximum bores are
shown in Table 13 on Page 36.
Torque ratings of couplings utilizing Taper-Lock bushings can
differ from those that do not. Refer to Falk for details.
If Falk is to supply coupling hubs bored for Taper-Lock
bushings, the bushing manufacturer MUST be noted on the
order.
Consult Falk when limited end float is required.
Reference Notes
Peak torque capacity is two times the published rating. Torque
ratings for hubs with bushings differ from those shown, refer to
Table 19, Page 39.
Consult Factory for higher speeds.
H Warranty extends for 3 years from date of shipment. Does not apply to Falk
Omnibox, Ultramite, Fluid Couplings, Renew and spare parts. Warranty applies to
Steelflex and Lifelign couplings with the use of Falk Long Term grease.
Copyright 1963, 2005. Rexnord Industries, Inc. All Rights Reserved. Litho in U.S.A.
FALK, REXNORD, STEELFLEX and a good name in industry are registered trademarks.
Dodge is a registered trademark.
Taper-Lock is a registered trademark of a bushing under license.
The contents of this selection guide are subject to change without notice or obligation.
Information contained herein should be confirmed before placing orders.
(421-110) 5
WARNING! Mixing grid coupling components from different manufacturers may cause premature
failure and possible personal injury or property damage from flying debris.
6 (421-110)
How to Select
Standard Selection Method (except T41/T44 &T63)
Transmitted HP x 5250
rpm
Transmitted HP x 5250
rpm
(421-110) 7
How to Select
Formula Selection Method (except T41/T44 & T63)
2 x Peak HP x 63,000
rpm
.5 x Peak HP x 63,000
rpm
HP per 100
rpm t
Torque
Rating
(lb-in)
T10
T20 &
T50 Q
T70
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
1210T
1220T
1230T
1240T
1250T
1260T
.73
2.09
3.49
6.11
9.60
14.0
28.8
52.4
88.1
131
192
279
401
559
785
1,047
1,452
1,920
2,618
3,491
4,712
6,109
7,854
10,472
13,090
460
1,320
2,200
3,850
6,050
8,800
18,150
33,000
55,550
82,500
121,000
176,000
253,000
352,000
495,000
660,000
915,200
1,210,000
1,650,000
2,200,000
2,970,000
3,850,000
4,950,000
6,600,000
8,250,000
4500
4500
4500
4500
4350
4125
3600
3600
2440
2250
2025
1800
1650
1500
1350
1225
1100
1050
900
820
730
680
630
580
540
6000
6000
6000
6000
6000
5500
4750
4000
3250
3000
2700
2400
2200
2000
1750
1600
1400
1300
1200
...
...
...
...
...
...
3600
3600
3600
3600
3600
3600
3600
3600
2440
2250
2025
1800
1650
1500
1350
1225
1100
1050
900
...
...
...
...
...
...
...
10000
...
9000
...
8200
7100
6000
4900
4500
4000
3600
3300
...
...
...
...
...
...
...
...
...
...
...
...
t HP per 100 rpm and torque rating values for hubs with Taper Lock bushings
differ from those shown above. Refer to Table 19, Page 39.
Q Speeds shown above are for single Type T50 couplings; speeds for Type T50
8 (421-110)
How to Select
Type T41 Controlled Torque Couplings & T44
Controlled Torque Clutches
Type T41 Controlled Torque Couplings
1. RUNNING TORQUE: Calculate normal running torque
Required HP x 63,000
Running Torque (lb - in) =
rpm
2. SLIP TORQUE: Slip torque = Running Torque x 150%
(Overload Setting.) Falk recommends a minimum 150%
overload setting for steady or moderate shock load
applications. For heavy shock load applications, a 200% or
greater overload setting may be required.
3. COUPLING SIZE: Refer to Table 8, Page 20 Trace down
the Slip Torque column to a figure equal to or in excess of the
calculated slip torque determined in Step 2. Read the coupling
size in the next column.
4. CHECK:
A. Check shaft diameters against coupling maximum bores
shown in Table 8, Page 20. If selection does not have
adequate bore capacity, refer to Table 15, Page 37 or Table
17, Page 38 for maximum bores with square or rectangular
keys, or select the next larger size coupling.
B. Check the required speed against the allowable speed
shown in Table 8. If a higher speed is required, refer
application details to the local Falk representative.
C. Check allowable slip torque times from Slip Torque
Performance Charts on Pages 24 through 27. The length of
time a coupling can slip without exceeding its thermal
capacity is a function of the slip torque setting and the
operating speed. An automatic cutout switch, Page 23, can
be provided when damaging thermal conditions exist.
D. Check application dimension requirements against selected
coupling dimensions shown on Page 20.
E. Check usable shaft length to the coupling hub lengths on
Page 18. If necessary, overhang hubs within the limits
specified on Page 23.
SELECTION EXAMPLE
Select a controlled torque coupling to connect a 20 hp, 1750
rpm, 256T frame motor to the high speed shaft of a gear drive
driving a screw feeder. Motor shaft diameter is 1.625" with a
usable shaft length of 4.000". Drive high speed shaft diameter is
1.375" with usable shaft length of 2.500".
1. RUNNING TORQUE: From Step 1 above:
20 HP x 63,000
Running Torque (lb - in) =
= 720 lb - in
rpm
2. SLIP TORQUE: From Step 2 above: Slip Torque = 720 x
150% = 1080 lb-in
3. SIZE: From Table 8, Page 20, the Size 40T41 has a maximum
slip torque of 1,480 lb-in.
4. CHECK:
A. The preferred mounting arrangement is to have the T41 hub
on the motor shaft (for optimum cooling during slippage).
From Table 8, Page 20, the Size 40T41 (T41 hub) has
maximum bore capacity of only 1.375" with square key and
is too small; however using an optional rectangular key
(Table 17, Page 38) allows a maximum bore of 1.625"
which meets the requirement. Size 40T41 has sufficient bore
capacity, 1.625".
B. Allowable Speed of 3600 rpm exceeds required 1750 rpm.
C. From Page 24, the Size 1040T41 with slip torque setting of
1080 lb-in and running speed of 1750 rpm will permit 23
seconds slip if followed by 7 minutes 30 seconds of
non-slip.
D. See Page 20 for dimensions.
E. Usable shaft length of motor is 4.000" and W dimension
for T41 hub is 3.12", therefore no overhang required.
Usable shaft length of drive is 2.500" and C dimension of
T hub is 2.00", therefore no overhang required.
Required HP x 63,000
rpm
(421-110) 9
Actual HP
3/4
1 1/2
7 1/2
10
15
20
25
30
40
50
60
75
100
125
150
200
250
300
1.00
1.25
1.50
1.75
2.00
2.50
3.00
3.50
.75
.94
1.1
1.3
1.5
1.9
2.3
2.6
1.0
1.25
1.5
1.8
2.0
2.5
3.0
3.5
1.5
1.9
2.3
2.6
3.0
3.8
4.5
5.3
2.0
2.5
3.0
3.5
4.0
5.0
6.0
7.0
3.0
3.8
4.5
5.3
6.0
7.5
9.0
10.5
5.0
6.3
7.5
8.8
10.0
12.5
15.0
17.5
7.5
9.4
11.3
13.1
15.0
18.8
22.5
26.2
10
12.5
15
18
20
25
30
35
15
19
23
26
30
38
45
52
20
25
30
35
40
50
60
70
25
31
38
44
50
63
75
87
30
38
45
53
60
75
90
105
40
50
60
70
80
100
120
140
50
63
75
88
100
125
150
175
60
75
90
105
120
150
180
210
75
94
113
131
150
187
225
262
100
125
150
175
200
250
300
350
125
156
188
219
250
312
375
437
150
188
225
262
300
375
450
525
200
250
300
350
400
500
600
700
250
312
375
438
500
625
750
875
350
400
450
500
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1.125
4500 rpm
6000 rpm
460
0.73
1.375
4500 rpm
6000 rpm
1320
2.09
1.625
4500 rpm
6000 rpm
2200
3.49
1.875
4500 rpm
6000 rpm
3850
6.11
2.125
4350 rpm
6000 rpm
6050
9.60
2.500
4125 rpm
5500 rpm
8,800
14.0
3.000
3600 rpm
4750 rpm
18,150
28.8
3.500
3600 rpm
4000 rpm
33,000
52.4
4.000
2440 rpm
3250 rpm
55,550
88.1
4.500
2250 rpm
3000 rpm
82500
131
5.000
2025 rpm
2700 rpm
121000
192
6.000
1800 rpm
2400 rpm
176000
279
1885
1571
1309
1100
942
916
759
613
524
456
377
340
304
272
220
183
147
120
99
81
65
52
44.0
35.6
29.3
23.6
19.4
15.7
13.1
10.5
8.6
6.8
5.8
4.7
3.9
2.6
2644
2203
1851
1587
1542
1278
1031
881
767
635
573
511
458
370
308
247
203
167
137
110
88
74
60
49
39.7
32.6
26.4
22.0
17.6
14.5
11.5
9.7
7.9
6.6
4.4
3927
3273
2749
2356
2291
1898
1532
1309
1139
942
851
759
681
550
458
367
301
249
203
164
131
110
89
73
59
48.4
39.3
32.7
26.2
21.6
17.0
14.4
11.8
9.8
6.5
3456
3456
3456
3360
2784
2246
1920
1670
1382
1248
1114
998
806
672
538
442
365
298
240
192
161
131
108
86
71
58
48.0
38.4
31.7
25.0
21.1
17.3
14.4
9.6
5864
5027
4887
4049
3267
2793
2430
2011
1815
1620
1452
1173
977
782
642
531
433
349
279
235
190
156
126
103
84
70
56
46.1
36.3
30.7
25.1
20.9
14.0
HP Ratings
RPM
4500
3600
3000
2500
2100
1800
1750
1450
1170
1000
870
720
650
580
520
420
350
280
230
190
155
125
100
84
68
56
45
37
30
25
20
16.5
13
11
9
7.5
5
32.8
26.3
21.9
18.2
15.3
13.1
12.8
10.6
8.5
7.3
6.3
5.3
4.7
4.2
3.8
3.1
2.6
2.0
1.7
1.4
1.1
0.9
0.73
0.61
0.50
0.41
0.33
0.27
0.22
0.18
0.15
0.12
0.095
0.080
0.066
0.055
0.036
94.2
75.4
62.8
52.4
44.0
37.7
36.7
30.4
24.5
20.9
18.2
15.1
13.6
12.1
10.9
8.8
7.3
5.9
4.8
4.0
3.2
2.6
2.1
1.8
1.4
1.17
0.94
0.77
0.63
0.52
0.42
0.35
0.27
0.23
0.19
0.16
0.10
10 (421-110)
157
126
105
87
73.3
62.8
61.1
50.6
40.8
34.9
30.4
25.1
22.7
20.2
18.2
14.7
12.2
9.8
8.0
6.6
5.4
4.4
3.5
2.9
2.4
2.0
1.6
1.3
1.0
0.9
0.70
0.58
0.45
0.38
0.31
0.26
0.17
275
220
183
153
128
110
107
89
71.5
61.1
53.1
44.0
39.7
35.4
31.8
25.7
21.4
17.1
14.0
11.6
9.5
7.6
6.1
5.1
4.2
3.4
2.7
2.3
1.8
1.5
1.2
1.0
0.79
0.67
0.55
0.46
0.31
432
346
288
240
202
173
168
139
112
96
84
69
62.4
55.7
49.9
40.3
33.6
26.9
22.1
18.2
14.9
12.0
9.6
8.1
6.5
5.4
4.3
3.6
2.9
2.4
1.9
1.6
1.2
1.1
0.86
0.72
0.48
628
503
419
349
293
251
244
202
163
140
121
101
91
81
73
59
49
39.1
32.1
26.5
21.6
17.5
14.0
11.7
9.5
7.8
6.3
5.2
4.2
3.5
2.8
2.3
1.8
1.5
1.3
1.0
0.7
1296
1037
864
720
605
518
504
418
337
288
251
207
187
167
150
121
101
81
66
55
44.6
36.0
28.8
24.2
19.6
16.1
13.0
10.7
8.6
7.2
5.8
4.8
3.7
3.2
2.6
2.2
1.4
1150T
1160T
1170T
1180T
1190T
1200T
1210T
1220T
1230T
1240T
1250T
1260T
8.000
1500 rpm
2000 rpm
352000
559
9.000
1350 rpm
1750 rpm
495000
785
10.000
1225 rpm
1600 rpm
660000
1047
11.000
1100 rpm
...
915200
1452
12.000
1050 rpm
...
1210000
1920
13.000
900 rpm
...
1,650,000
2618
14.000
820 rpm
...
2200000
3491
15.000
730 rpm
...
2970000
4712
16.000
680 rpm
...
3850000
6109
17.000
630 rpm
...
4950000
7854
18.500
580 rpm
...
6600000
10472
20.000
540 rpm
...
8,250,000
13090
25133
22689
20246
18152
14661
12217
9774
8029
6632
5411
4363
3491
2932
2374
1955
1571
1292
1047
873
698
576
471
384
314
262
175
33929
30631
27332
24505
19792
16493
13195
10839
8954
7304
5891
4712
3958
3204
2639
2121
1744
1414
1178
942
778
636
518
424
353
236
39706
35430
31765
25656
21380
17104
14050
11607
9468
7636
6109
5131
4154
3421
2749
2260
1833
1527
1222
1008
825
672
550
458
305
45553
40841
32987
27489
21991
18064
14923
12174
9818
7854
6597
5341
4398
3534
2906
2356
1964
1571
1296
1060
864
707
589
393
60738
54455
43983
36652
29322
24086
19897
16232
13090
10472
8797
7121
5864
4712
3875
3142
2618
2094
1728
1414
1152
942
785
524
68068
54978
45815
36652
30107
24871
20290
16363
13090
10996
8901
7330
5891
4843
3927
3273
2618
2160
1767
1440
1178
982
655
HP Ratings
RPM
2100
1800
1750
1450
1170
1000
870
720
650
580
520
420
350
280
230
190
155
125
100
84
68
56
45
37
30
25
20
16.5
13.5
11.0
9.0
7.5
5.0
8430
7226
7025
5821
4697
4014
3492
2890
2609
2328
2087
1686
1405
1124
923
763
622
502
401
337
273
225
181
149
120
100
80
66
54
44.2
36.1
30.1
20.1
10053
9774
8098
6535
5585
4859
4021
3630
3239
2904
2346
1955
1564
1285
1061
866
698
559
469
380
313
251
207
168
140
112
92
75
61
50
42
27.9
13745
11388
9189
7854
6833
5655
5105
4555
4084
3299
2749
2199
1806
1492
1217
982
785
660
534
440
353
291
236
196
157
130
106
86
71
59
39
15184
12252
10472
9111
7540
6807
6074
5445
4398
3665
2932
2409
1990
1623
1309
1047
880
712
586
471
387
314
262
209
173
141
115
94
79
52
14521
12633
10455
9439
8422
7551
6099
5082
4066
3340
2759
2251
1815
1452
1220
987
813
653
537
436
363
290
240
196
160
131
109
73
19199
16703
13823
12479
11135
9983
8063
6720
5376
4416
3648
2976
2400
1920
1613
1306
1075
864
710
576
480
384
317
259
211
173
144
96
22777
18850
17017
15184
13614
10996
9163
7330
6021
4974
4058
3273
2618
2199
1780
1466
1178
969
785
655
524
432
353
288
236
196
131
(421-110) 11
Service Factors
TABLE 4 Flexible Coupling Service Factors for Motor
Service factors listed are typical values based on normal operation of the drive systems.
Service
Factor
Service
Factor
AERATOR ..........................................2.0
AGITATORS
Vertical and Horizontal
Screw, Propeller, Paddle ...............1.0
BARGE HAUL PULLER ......................1.5
BLOWERS
Centrifugal ......................................1.0
Lobe or Vane ...................................1.25
CAR DUMPERS .................................2.5
CAR PULLERS....................................1.5
CLARIFIER OR CLASSIFIER ..............1.0
COMPRESSORS
Centrifugal ......................................1.0
Rotary, Lobe or Vane........................1.25
Rotary, Screw ...................................1.0
Reciprocating
Direct Connected .................Refer to Falk
Without Flywheel ..................Refer to Falk
QWith Flywheel and Gear
between Compressor
and Prime Mover
1 cylinder, single acting.............3.0
1 cylinder, double acting ...........3.0
2 cylinders, single acting ...........3.0
2 cylinders, double acting .........3.0
3 cylinders, single acting ...........3.0
3 cylinders, double acting .........2.0
4 or more cly., single act...........1.75
4 or more cyl., double act. ........1.75
sCONVEYORS
Apron, Assembly, Belt, Chain,
Flight, Screw.................................1.0
Bucket .............................................1.25
Live Roll, Shaker and
Reciprocating ...............................3.0
sCRANES AND HOIST
Main Hoist...................................1.75s
Skip Hoist....................................1.75s
Slope...............................................1.5
Bridge, Travel or Trolley ...................1.75
DYNAMOMETER...............................1.0
ELEVATORS
Bucket, Centrifugal Discharge ..........1.25
Freight or Passenger .............Not
Approved
Gravity Discharge ............................1.25
ESCALATORS ................... Not Approved
EXCITER, GENERATOR..................... 1.0
EXTRUDER, PLASTIC......................... 1.5
FANS
Centrifugal ......................................1.0
Cooling Tower .................................2.0
Forced Draft Across the
Line start ......................................1.5
Forced Draft Motor
Driven thru fluid or
electric slip clutch .........................1.0
Gas Recirculating.............................1.5
Induced Draft with damper
control or blade cleaner................1.25
Induced Draft without controls ..........2.0
FEEDERS
Apron, Belt, Disc, Screw ...................1.0
Reciprocating...................................2.5
GENERATORS
Even Load........................................1.0
compressors and other machines fitted with sleeves or straight roller bearings
usually require limited end float couplings. If in doubt, provide axial clearances and
centering forces to Falk for a recommendation.
Q For balanced opposed design, refer to Falk.
s If people are occasionally transported, refer to Falk for the selection of the proper
size coupling.
For high peak load applications (such as Metal Rolling Mills) refer to the Falk.
4 or 5
No. of Cylinders
Table 2 S.F.
1.0
1.25
1.5
1.75
2.0
1.0
1.25
1.5
1.75
2.0
Engine S.F.
2.0
2.25
2.5
2.75
3.0
1.5
1.75
2.0
2.25
2.5
To use Table 5, first determine application service factor from Table 4. Use that
factor to determine ENGINE Service Factor from Table 5. When service factor
from Table 4 is greater than 2.0, or where 1, 2, or 3 cylinder engines are
involved, refer complete application details to Falk Engineering.
12 (421-110)
Service
Factor
Service
Factor
AGGREGATE PROCESSING,
CEMENT, MINING KILNS;
TUBE, ROD AND BALL MILLS
Direct or on L.S. shaft of
Reducer, with final drive
Machined Spur Gears ...................2.0
Single Helical or
Herringbone Gears ...................1.75
Conveyors, Feeders, Screens,
Elevators..................See General Listing
Crushers, Ore or Stone ....................2.5
Dryer, Rotary....................................1.75
Grizzly .............................................2.0
Hammermill or Hog .........................1.75
Tumbling Mill or Barrel.....................1.75
BREWING AND DISTILLING
Bottle and Can
Filling Machines ...........................1.0
Brew Kettle.......................................1.0
Cokers, Continuous Duty..................1.25
Lauter Tub .......................................1.5
Mash Tub ........................................1.25
Scale Hopper, Frequent Peaks ..........1.75
CLAY WORKING INDUSTRY
Brick Press, Briquette Machine,
Clay Working Machine,
Pug Mill .......................................1.75
DREDGES
Cable Reel.......................................1.75
Conveyors .......................................1.25
Cutter head, Jig Drive ......................2.0
Maneuvering Winch .........................1.5
Pumps (uniform load) .......................1.5
Screen Drive, Stacker .......................1.75
Utility Winch ....................................1.5
FOOD INDUSTRY
Beet Slicer........................................1.75
Bottling, Can Filling Machine ...........1.0
Cereal Cooker .................................1.25
Dough Mixer, Meat Grinder .............1.75
LUMBER
Band Resaw .....................................1.5
Circular Resaw, Cut-off ....................1.75
Edger, Head Rig, Hog ......................2.0
Gang Saw
(Reciprocating)..................Refer to Falk
Log Haul .........................................2.0
Planer..............................................1.75
Rolls, Non-Reversing ........................1.25
Rolls, Reversing ................................2.0
Sawdust Conveyor............................1.25
Slab Conveyor .................................1.75
Sorting Table ...................................1.5
Trimmer ...........................................1.75
METAL ROLLING MILLS
Coilers (Up or Down) Cold
Mills only .....................................1.5
Coilers (Up or Down) Hot
Mills only .....................................2.0
Coke Plants
Pusher Ram Drive .........................2.5
Door Opener ...............................2.0
Pusher or Larry Car
Traction Drive ...........................3.0
Continuous Caster ...........................1.75
Cold Mills
Strip Mills .........................Refer to Falk
Temper Mills ........................Refer to Falk
Cooling Beds ...................................1.5
Drawbench ......................................2.0
Feed Rolls - Blooming Mills ..............3.0
Furnace Pushers ...............................2.0
Hot and Cold Saws ..........................2.0
Hot Mills
Strip or Sheet Mills ............Refer to Falk
Reversing Blooming...........Refer to Falk
or Slabbing Mills ...............Refer to Falk
Edger Drives .....................Refer to Falk
Ingot Cars .......................................2.0
Manipulators ...................................3.0
Merchant Mills .....................Refer to Falk
Mill Tables
Roughing Breakdown
Mills .........................................3.0
Hot Bed or Transfer,
non-reversing............................1.5
Runout, reversing..........................3.0
Runout, non-reversing,
non-plugging ............................2.0
Reel Drives.......................................1.75
Rod Mills..............................Refer to Falk
Screwdown ......................................2.0
Seamless Tube Mills
Piercer .........................................3.0
Thrust Block .................................2.0
Tube Conveyor Rolls .....................2.0
Reeler ..........................................2.0
Kick Out ......................................2.0
Shear, Croppers ...................Refer to Falk
Sideguards.......................................3.0
Skelp Mills ...........................Refer to Falk
Typical
Service
Factor
3. Speed (RPM)
1.5
2.0
C. Frequency of stops.
D. Rate of deceleration required desired stop time and
stopping rpm.
2.5
5. Quantity
6. Coupling Size and Type e.g., 110T41 or 1070T10
7. Shaft Gap or distance between shaft ends (BE Dimension)
3.0
Consult
Falk
Engineering
Driven Shaft
Diameter U
Diameter U
Tolerance
Tolerance
Length V
Length V
Keyway
Keyway
IF MACHINES ARE
IN PLACE FURNISH
GAP DIMENSION.
1.0
Applications like
Reciprocating Compressors
with frequent torque reversals,
which do not necessarily cause
reverse rotations.
How to Order
ZW
GAP
TAPER PER LENGTH
ON DIAMETER
Across Flats
Length V
Corners ZW
Length W
Taper
Length X
Keyway
Length Y
(421-110) 13
Type T10
Close Coupled/Dimensions Inches
GRID
HUB
S
A
GAP
F
C
D
A
SIZES 1240 - 1260
Sizes 1020 thru 1230T10 covers are cast aluminum alloy; Sizes
1240 thru 1260T10 are fabricated steel.
LUBE
PLUGS
J
B
DIMENSIONS INCHES
Torque
Rating
(lb-in)
Allow
Speed
rpm
Max
Bore l
Min
Bore n
Cplg Wt
With No
Bore-lb
Lube Wt
lb
Gap
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
1210T
1220T
1230T
1240T
1250T
1260T
460
1,320
2,200
3,850
6,050
8,800
18,150
33,000
55,550
82,500
121,000
176,000
253,000
352,000
495,000
660,000
915,000
1,210,000
1,650,000
2,200,000
2,970,000
3,850,000
4,950,000
6,600,000
8,250,000
4500
4500
4500
4500
4350
4125
3600
3600
2440
2250
2025
1800
1650
1500
1350
1225
1100
1050
900
820
730
680
630
580
540
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250
8.000
9.000
10.000
11.000
12.000
13.000
14.000
15.000
16.000
17.000
18.500
20.000
.500
.500
.500
.500
.750
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
4.250
4.750
5.250
6.000
6.000
7.000
7.000
8.000
8.000
10.000
10.000
10.000
4.2
5.7
7.4
12
16
23
39
56
93
120
179
266
392
500
681
987
1365
1710
2331
3140
3935
4997
6504
8450
10322
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.12
1.62
2.0
2.5
4.3
6.2
7.7
8.3
9.7
12.4
23.2
35.4
53.0
74.5
110.5
148.1
3.82
4.16
4.50
5.32
5.82
6.25
7.50
8.31
9.88
10.62
12.12
13.62
15.12
17.84
19.76
22.32
24.80
26.60
29.80
33.25
36.25
39.50
42.80
46.50
49.64
3.88
3.88
4.12
4.88
5.12
6.12
7.12
7.88
9.69
10.19
12.00
13.00
14.75
14.65
15.85
17.25
19.05
20.65
22.25
24.50
26.10
27.70
29.50
32.10
34.50
1.88
1.88
2.00
2.38
2.50
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
7.20
7.80
8.50
9.40
10.20
11.00
12.00
12.80
13.60
14.50
15.80
17.00
1.56
1.94
2.25
2.62
3.00
3.44
4.12
4.88
5.59
6.31
7.06
8.56
10.00
10.60
12.00
14.00
15.50
17.20
19.60
21.00
22.50
24.00
25.50
28.00
30.00
....
....
....
....
....
....
....
....
....
....
....
....
....
15.40
17.20
19.18
21.84
23.93
26.00
29.56
32.37
35.62
....
....
....
2.62
2.69
2.75
3.19
3.68
3.81
4.55
4.81
6.12
6.36
7.54
7.68
7.92
10.69
10.96
12.10
12.64
12.80
14.00
17.00
19.30
21.50
25.50
27.50
30.00
1.54
1.54
1.58
1.76
2.06
2.12
2.54
2.82
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
.250
.250
.250
.250
.500
.500
.500
.500
.500
.500
SIZE
14 (421-110)
Type T20
Close Coupled/Dimensions Inches
CLEARANCE FOR
GRID REMOVAL
LUBE
PLUGS
GRID
HUB
GAP
S
A
J
B
SIZE
H
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
Torque
Rating
(lb-in)
Allow
Speed
rpm
Max
Bore l
Min
Bore n
460
1,320
2,200
3,850
6,050
8,800
18,150
33,000
55,550
82,500
121,000
176,000
253,000
352,000
495,000
660,000
6000
6000
6000
6000
6000
5500
4750
4000
3250
3000
2700
2400
2200
2000
1750
1600
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250
8.000
9.000
10.000
.500
.500
.500
.500
.750
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
4.250
4.750
5.250
Cplg Wt
Without
Bore-lb
4.3
5.7
7.4
12
15
23
39
56
93
120
180
270
397
507
708
988
DIMENSIONS INCHES
Lube Wt
lb
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.12
1.62
2.0
2.5
4.3
6.2
7.7
4.42
4.80
5.11
5.86
6.42
6.86
7.92
9.17
10.55
11.30
12.61
14.92
16.42
18.75
21.00
23.00
3.88
3.88
4.12
4.88
5.12
6.12
7.12
7.88
9.69
10.19
12.00
13.00
14.75
14.65
15.85
17.25
1.88
1.88
2.00
2.38
2.50
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
7.20
7.80
8.50
1.56
1.94
2.25
2.62
3.00
3.44
4.12
4.88
5.59
6.31
7.06
8.56
10.00
10.60
12.00
14.00
2.50
2.88
3.25
3.88
4.38
4.88
5.88
6.62
7.75
8.50
9.62
11.12
12.62
14.72
16.68
18.68
H
.38
.38
.38
.47
.50
.50
.50
.50
.62
.63
.69
.81
.81
.76 t
1.18 t
1.18 t
Gap
.94
.98
1.02
1.20
1.25
1.32
1.72
1.85
2.35
2.47
2.90
2.95
3.08
4.21
4.50
4.70
1.88
1.88
2.00
2.38
2.50
2.62
3.50
3.75
4.75
4.88
5.62
5.75
6.12
8.00
8.50
8.90
1.54
1.54
1.58
1.76
2.06
2.12
2.54
2.82
....
....
....
....
....
....
....
....
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
.250
t Dimension H is to the end of the bolt on Sizes 1150 thru 1170. Bolts are not shrouded.
(421-110) 15
Type T31
Full Spacer/Dimensions Inches
GRID
COVER
FLANGE
FASTENERS
GAP
S
E
A
B
DD
BETWEEN
SHAFT ENDS
BE
SHAFT HUB
SHAFT HUB
LUBE PLUGS
SPACER HUB
SPACER HUB
SIZE
H
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
Cplg Wt Wt Added
Torque
With No Per Inch Lube
Allow
Rating
Max
Min
Wt
Bore & of BE
Speed
(lb-in)
Bore l Bore n
Min BE over Min lb
rpm
(lb)
460
1,320
2,200
3,850
6,050
8,800
18,150
33,000
55,550
82,500
121,000
176,000
253,000
3600
3600
3600
3600
3600
3600
3600
3600
2440
2250
2025
1800
1650
1.375
1.625
2.125
2.375
2.875
3.125
3.500
4.000
4.750
5.500
6.250
7.000
8.000
.500
.500
.500
.500
.750
.750
1.062
1.062
1.500
2.000
2.500
3.000
3.500
8.5
11.5
18.6
28.2
45.1
54.6
88.1
132
199
261
392
522
720
0.57
0.87
1.17
1.58
2.06
2.69
3.86
5.37
6.95
8.98
11.2
16.5
22.4
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.12
1.62
2.00
2.50
DIMENSIONS INCHES
Flange Fasteners
BE
A
3.82
4.16
4.50
5.32
5.82
6.25
7.50
8.31
9.88
10.62
12.12
13.62
15.12
1.38
1.62
2.12
2.38
2.88
3.12
3.50
4.00
3.56
4.10
4.70
5.30
6.00
Min
Max
3.50
3.50
3.50
4.37
4.81
5.00
6.12
6.44
8.00
8.25
9.69
10.12
10.50
8.00
8.50
8.50
8.50
13.00
13.00
16.00
16.00
16.00
16.00
16.00
16.00
16.00
DD
Gap
2.06
2.34
3.09
3.44
4.06
4.31
4.81
5.62
6.75
7.75
8.88
9.38
10.50
.03
.03
.03
.03
.06
.06
.06
.06
.06
.06
.06
.06
.06
3.38
3.69
4.44
4.94
5.69
6.00
7.00
8.25
9.88
10.88
12.56
13.62
15.19
1.08
1.24
1.08
1.60
1.70
1.84
1.96
2.24
....
....
....
....
....
.08
.08
.08
.08
.11
.11
.11
.11
.12
.12
.16
.16
.16
.188
.188
.188
.188
.188
.188
.188
.188
.250
.250
.375
.375
.375
No. per
Dia
Flange &
Inches
SAE Grade
4, Gr 8
8, Gr 8
8, Gr 8
8, Gr 8
8, Gr 8
12, Gr 8
12, Gr 5
12, Gr 5
12, Gr 5
12, Gr 5
12, Gr 5
12, Gr 5
12, Gr 5
.250
.250
.250
.312
.375
.375
.500
.625
.750
.750
.875
1.000
1.125
16 (421-110)
COUPLING SIZE
Inch
Millimeters
Pump
Std
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
3.50
3.94
4.25
4.38
4.69
5.00
5.22
5.38
5.51
5.66
5.81
5.97
6.12
6.94
7.00
7.09
7.25
8.00
8.59
8.62
8.88
9.75
9.84
9.94
11.09
12.25
14.05
89
100
108
111
119
127
133
137
140
144
148
152
155
176
178
180
184
203
218
219
226
248
250
252
282
311
357
ANSI
ISO
MISC
ANSI
MISC
ANSI
MISC
MISC
ISO
MISC
MISC
MISC
MISC
MISC
ANSI
ISO
ANSI
MISC
MISC
MISC
MISC
ANSI
ISO
MISC
MISC
ANSI
MISC
X
X
X
X
X
X
...
...
X
...
...
...
...
X
...
...
...
...
...
...
...
...
...
...
...
...
...
X
X
X
X
X
X
...
X
X
X
X
...
X
X
...
...
X
...
...
...
...
...
...
...
...
...
...
X
X
X
X
X
X
X
X
X
X
X
X
X
X
...
X
X
...
...
...
...
...
...
...
...
...
...
...
...
...
X
X
X
...
...
X
...
X
X
X
X
...
X
X
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
X
...
...
X
...
...
...
X
X
...
...
X
...
...
X
...
X
...
...
...
X
...
...
...
...
...
...
X
...
...
X
...
...
...
X
...
X
X
X
...
...
X
...
X
...
...
...
X
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
X
X
X
...
X
...
...
X
...
X
X
X
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
X
X
...
...
...
...
X
...
...
...
X
...
...
...
X
...
...
X
X
X
...
...
...
...
...
...
...
...
...
...
X
X
...
...
...
X
Type T31
Full Spacer/Dimensions Inches
.12
REGISTER DETAIL
SIZES 1150, 1160, 1170
E
FLANGE
FASTENERS
GRID
COVER
REGISTER DETAIL
SIZES 1180, 1190, 1200
U
GREASE
RETAINERS
GAP
B
BE
DD
SHAFT HUB
SHAFT HUB
LUBE
PLUGS
SPACER HUB
SIZE
H
G52
Rigid
Hub
Size
Q
1150T
1160T
1170T
1180T
1190T
1200T
DIMENSIONS INCHES
Cplg Wt Wt Added
With No Per Inch Lube
Torque Allow
Max
Min
Wt
Bore &
Rating Speed
of BE
Bore l Bore n
lb
Min BE over Min
(lb-in) rpm
(lb)
1055G 352,000
1060G 495,000
1070G 660,000
1080G 915,000
1080G 1,210,000
1100G 1,650,000
1500
1350
1225
1100
1050
900
10.000
11.000
13.000
13.000
14.250
15.000
4.000
4.500
5.000
4.000
4.500
5.000
1018
1247
1887
2502
3362
4211
10.8
14.0
21.3
26.5
33.8
47.8
4.3
6.2
7.7
8.3
9.7
12.4
SPACER HUB
Flange Fasteners
BE
A
17.84
19.74
22.30
24.80
26.60
29.80
6.80
7.34
8.67
9.80
10.86
12.02
Min
Max
13.56
14.00
15.13
15.75
16.19
17.50
14.62
16.00
17.50
19.31
20.88
22.62
DD t
Gap
13.16
14.41
16.73
17.75
20.00
20.88
.20
.26
.33
.20
.20
.24
16.75
18.00
20.75
23.25
26.00
28.00
...
...
...
.32
.32
.36
.375
.375
.375
.375
.375
.375
No. per
Dia
Flange &
Inches
SAE Grade
14, Gr 8
14, Gr 8
16, Gr 8
16, Gr 5
18, Gr 5
18, Gr 5
.875
.875
1.000
1.125
1.250
1.250
t Dimension DD is for an as-cast, unmachined surface for Sizes 1180, 1190 and 1200T.
Q Type T31 couplings shown use Type G52 gear coupling rigid hubs as the shaft hubs.
(421-110) 17
Type T35
Half Spacer/Dimensions Inches
GAP
FLANGE FASTENER
COVER
GRID
U
S
C
D
DD
BETWEEN
SHAFT ENDS
BE
T HUB
SHAFT HUB
LUBE PLUGS
SPACER HUB
Torque Allow
SIZE Rating Speed
H
(lb-in) rpm
1020T
460 3600
1030T
1,320 3600
1040T
2,200 3600
1050T
3,850 3600
1060T
6,050 3600
1070T
8,800 3600
1080T 18,150 3600
1090T 33,000 3600
1100T 55,550 2440
1110T 82,500 2250
1120T 121,000 2025
1130T 176,000 1800
1140T 253,000 1650
Max
Bore l
Min
Bore
Shaft
Hub
T
Hub
1.375
1.625
2.125
2.375
2.875
3.125
3.500
4.000
4.750
5.500
6.250
7.000
8.000
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250
.500
.500
.500
.500
.750
.750
1.062
1.062
1.625 t
1.625 t
2.375 t
2.625 t
2.625 t
Wt
Cplg Wt Added
With No Per Lube
Bore & Inch of Wt
Min BE BE over lb
lb
Min
6.4
8.6
13.0
20.1
30.7
38.8
63.8
94.4
146
191
285
394
556
0.57
0.87
1.17
1.58
2.06
2.69
3.86
5.37
6.95
8.98
11.2
16.5
22.4
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.12
1.62
2.00
2.50
DIMENSIONS INCHES
Flange Fasteners
BE
A
3.82
4.16
4.50
5.32
5.82
6.25
7.50
8.31
9.88
10.62
12.12
13.62
15.12
1.38
1.62
2.12
2.38
2.88
3.12
3.50
4.00
3.56
4.10
4.70
5.30
6.00
Min Max
1.78
1.78
1.78
2.22
2.44
2.53
3.09
3.25
4.06
4.19
4.91
5.12
5.31
4.03
4.28
4.28
4.28
6.53
6.53
8.03
8.03
8.06
8.06
8.06
8.06
8.06
S
C
DD
Shaft
Hub
T
Hub
Gap
No. Per
Flange &
SAE Grade
Dia
Inches
.03
.03
.03
.03
.06
.06
.06
.06
.06
.06
.06
.06
.06
3.38
3.69
4.44
4.94
5.69
6.00
7.00
8.25
9.88
10.88
12.56
13.62
15.19
1.08
1.24
1.08
1.60
1.70
1.84
1.96
2.24
....
....
....
....
....
1.54
1.54
1.58
1.76
2.06
2.12
2.54
2.82
....
....
....
....
....
.08
.08
.08
.08
.11
.11
.11
.11
.12
.12
.16
.16
.16
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
4,Gr 8
8,Gr 8
8,Gr 8
8,Gr 8
8,Gr 8
12,Gr 8
12,Gr 5
12,Gr 5
12,G r5
12,Gr 5
12,Gr 5
12,Gr 5
12,Gr 5
.250
.250
.250
.312
.375
.375
.500
.625
.750
.750
.875
1.000
1.125
t Minimum bores are for the T Hub. Shaft hub bores are 1.500, 2.000, 2.500 and 3.500, respectively.
TABLE 7 Type T35 Half Spacer Coupling Standard Stock Spacer Lengths
Between Shaft Ends
Inch
Millimeters
1.78
2.22
2.53
2.79
350
3.53
3.66
3.58
4.06
4.94
5.00
5.51
6.16
6.19
7.09
45
56
64
71
89
90
93
91
103
125
127
140
156
157
180
Pump
Std
MISC
MISC
MISC
MISC
ANSI
MISC
MISC
MISC
MISC
MISC
ANSI
ISO
MISC
MISC
ISO
COUPLING
SIZE Q
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
X
X
X
X
X
...
...
...
...
...
...
...
...
...
...
X
X
X
X
X
...
X
...
...
...
...
...
...
...
...
X
X
X
X
X
...
X
...
...
...
...
...
...
...
...
...
X
X
X
X
...
X
...
...
...
...
...
...
...
...
...
...
X
X
X
...
X
...
...
...
...
...
X
...
...
...
...
X
X
...
X
X
X
...
...
...
...
X
...
...
...
...
...
...
...
X
X
X
...
...
X
X
X
...
...
...
...
...
...
...
...
X
X
...
...
...
X
X
...
X
...
...
...
...
...
...
...
...
X
X
X
X
...
X
...
...
...
...
...
...
...
...
...
...
X
X
...
...
...
X
Q CAUTION: To permit removal of T35 shaft hub without moving connected equipment, select a half spacer with dimension BE (in Table 7) greater than dimension B (in uppermost
table) or overhang the shaft hub. Refer to Falk for maximum overhang allowed.
18 (421-110)
Type
T35
.12
REGISTER DETAIL
SIZES 1150, 1160, 1170
E
FLANGE
FASTENERS
GRID
COVER
REGISTER DETAIL
SIZES 1180, 1190, 1200
GREASE
RETAINER
E
B
BE
BETWEEN
SHAFT ENDS
F
GAP
DD
T - HUB
SHAFT HUB
LUBE
PLUGS
SPACER HUB
SIZE
H
G52
Torque Allow
Rigid
Rating Speed
Hub
(lb-in) rpm
Size
Q
1150T
1160T
1170T
1180T
1190T
1200T
1055G 352,000
1060G 495,000
1070G 660,000
1080G 915,000
1090G 1,210,000
1100G 1,650,000
1500
1350
1225
1100
1050
900
Hub Bores
Shaft
Hub Q
T
Hub
4.000
4.500
5.000
4.000
4.500
5.000
8.000
9.000
10.000
11.000
12.000
13.000
4.250
4.750
5.250
6.000
6.000
7.000
Cplg Wt Wt Added
With No Per Inch Lube
Bore & of BE Wt
Min BE over Min lb A
lb
767
973
1437
1934
2536
3271
10.8
14.0
21.3
26.5
33.8
47.8
4.3
6.2
7.7
8.3
9.7
12.4
DIMENSIONS INCHES
B
17.84 6.80
19.74 7.34
22.30 8.67
24.80 9.80
26.60 10.86
29.80 12.02
BE
Flange Fasteners
DD t
No. Per
Dia
Gap Flange &
Inches
SAE Grade
10.60
12.00
14.00
15.50
17.20
19.60
13.16
14.41
16.73
17.75
20.00
20.88
.20
.26
.33
.20
.20
.24
16.75
18.00
20.75
23.25
26.00
28.00
...
...
...
.32
.32
.36
.250
.250
.250
.250
.250
.250
Min Max
6.87 7.38 7.20
7.07 8.06 7.80
7.64 8.81 8.50
7.94 9.72 9.40
8.16 10.50 10.20
8.81 11.38 11.00
14,Gr 8
14,Gr 8
16,Gr 8
16,Gr 5
18,Gr 5
18,Gr 5
.875
.875
1.000
1.125
1.250
1.250
t Dimension DD is for an as-cast, unmachined surface for Sizes 1180, 1190 and 1200T.
Q Type T35 couplings shown use Type G52 gear coupling rigid hubs as the shaft hubs.
(421-110) 19
Types
T41, T41-2
COVER
CLEARANCE
T41
HUB
GAP
D
A
T
HUB
LUBRICATE
THRU COVER
B
Y
Cplg Wt t
w/o Bore-lb
T41
20T
30T
40T
50T
60T
70T
80T
90T
100T
110T
120T
130T
140T
150T
160T
170T
180T
190T
200T
13.6
18.0
25.4
36.2
48.4
62.2
90.4
138
222
282
403
573
828
1106
1437
1916
2560
3143
3980
Lube
Wt
T41-2 lb
...
18.0
24.9
35.2
46.9
60.2
88.9
133
202
267
383
548
793
...
...
...
...
...
...
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.1
1.6
2.0
2.5
4.2
6.2
7.7
8.3
9.7
12.4
DIMENSIONSINCHES
A
4.00
4.38
4.62
5.44
5.94
6.38
7.62
8.38
9.88
10.62
12.12
13.62
15.12
17.84
19.74
22.30
24.80
26.50
29.80
5.12
5.12
5.24
5.94
6.42
7.20
8.12
9.06
10.60
11.35
13.43
14.21
15.32
17.11
17.91
19.29
21.13
22.15
23.67
1.88
1.88
2.00
2.38
2.50
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
7.20
7.80
8.50
9.40
10.20
11.00
1.56
1.94
2.24
2.62
3.00
3.44
4.12
4.88
5.60
6.32
7.06
8.56
10.00
10.60
12.00
14.00
15.50
17.20
19.60
7.00
7.94
9.12
10.64
11.86
12.74
14.24
16.28
19.34
21.38
23.24
26.92
30.18
34.00
38.92
41.96
45.70
49.76
54.22
G
2.50
2.74
3.24
3.24 Q
3.50
4.00
4.00
5.00
5.50
6.00
7.00
7.50
8.00
8.50
8.50
9.50
9.50
10.00
10.00
.22
.22
.22
.22
.32
.32
.32
.32
...
...
...
...
...
...
. ..
. ..
. ..
. ..
...
1.88
2.00
2.50
2.50
3.00
3.26
3.62
4.30
5.80
6.00
7.00
7.30
8.40
10.00
10.00
10.50
10.50
11.00
11.00
Gap
N
.42
.42
.48
.42
.60
.58
.58
.64
.82
.86
1.06
1.06
1.07
1.25
1.27
1.27
1.68
1.68
1.68
1.54
1.54
1.58
1.76
2.06
2.12
2.54
2.80
...
...
...
...
...
...
...
...
...
...
...
3.12
3.12
3.12
3.44
3.80
4.08
4.50
5.06
5.66
6.16
7.30
7.58
7.82
9.66
9.86
10.54
11.48
11.70
12.42
.20
.20
.20
.20
.20
.20
.20
.20
.20
.36
.36
.36
.36
.36
.36
.36
.36
.36
.36
H Refer to Page 5 for General Information and Reference Notes. Use a coupling guard that will permit air to
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
.250
.250
.250
.250
COUPLING
SIZE
Max
Maximum Bore
with
Recommended
Keys
T41 Hub T Hub
42
336
20T41
1.000
1.125
3600
50
110
140
880
30T41-2
30T41
1.250
1.375
3600
60
185
230
1,480
40T41-2
40T41
1.375
1.625
3600
80
300
370
2,400
50T41-2
50T41
1.750
1.875
3600
100
520
650
4,160
60T41-2
60T41
1.875
2.125
3600
120
770
960
6,160
70T41-2
70T41
2.250
2.500
3600
390
1,350
1,700
10,800
80T41-2
80T41
2.625
3.000
2800
660
2,250
2,800
18,000
90T41-2
90T41
3.125
3.500
2500
1,200
4,100
5,100
32,800
100T41-2
100T41
3.625
4.000
2100
1,800
6,100
7,600
48,800
110T41-2
110T41
4.000
4.500
1850
2,600
9,100
11,400
72,800
120T41-2
120T41
4.500
5.000
1750
3,800
13,000
16,200
104,000
130T41-2
130T41
5.250
6.000
1450
5,400
18,400
23,000
147,200
140T41-2
140T41
6.500
7.250
1300
26,000
36,000
49,000
67,000
90,000
120,000
208,000
288,000
392,000
536,000
720,000
960,000
150T41
160T41
170T41
180T41
190T41
200T41
7.000
8.500
9.500
11.000
12.000
13.000
8.000
9.000
10.000
11.000
12.000
13.000
1100
950
870
760
720
670
20 (421-110)
Allow
Speed
rpm
Types
T41
HUB
R-HOLES
H
P-DIA.
K
W
N-DIA.
T41
HUB
E-DIA.
DIMENSIONSINCHES
SIZE
H
20T
30T
40T
50T
60T
70T
80T
90T
100T
110T
120T
130T
140T
Cplg Wt t
w/o Bore-lb
R
E
T44
T44-2
11.6
14.3
18.9
29.4
35.2
45.2
63.0
97.5
167
232
288
452
637
...
14.3
18.4
28.4
33.7
43.2
60.5
92.5
157
217
268
427
602
7.00
7.94
9.12
10.64
11.86
12.74
14.24
16.28
19.34
21.38
23.24
26.92
30.18
.22
.22
.22
.22
.32
.32
.32
.32
...
...
...
...
...
.780
.730
.530
.750
.790
.970
1.210
1.350
1.270
1.480
2.160
2.160
2.160
1.00
1.00
.88
1.20
1.36
1.54
1.96
2.22
2.32
2.52
3.34
3.38
3.24
+.000
.000
1.750
2.250
2.625
3.000
3.500
4.000
4.750
5.500
6.250
6.750
7.625
9.250
11.000
Size
No.
(UNC)
Bolt
Circle
Dia
2.100
2.600
3.100
3.600
4.200
4.700
5.500
6.400
7.300
8.000
8.900
10.500
12.300
3.12
3.12
3.12
3.44
3.80
4.08
4.50
5.06
5.66
6.16
7.30
7.56
7.82
Max
Chain
Size
Slip Torquelb-in
Min
.20
.20
.20
.20
.20
.20
.20
.20
.20
.36
.36
.36
.36
40
50
60
80
100
100
140
160
180
180
200
200
200
Max
CLUTCH
SIZE
Maximum Bore
Allow
with
Speed
Recommended
rpm
Keys Q
42
336
20T44
1.000
3600
50
110
140
880
30T44-2
30T44
1.250
3600
60
185
230
1,480
40T44-2
40T44
1.375
3600
80
300
370
2,400
50T44-2
50T44
1.750
3600
100
520
650
4,160
60T44-2
60T44
1.875
3600
120
770
960
6,160
70T44-2
70T44
2.250
3600
390
1,350
1,700
10,800
80T44-2
80T44
2.625
2800
660
2,250
2,800
18,000
90T44-2
90T44
3.125
2500
1,200
4,100
5,100
32,800
100T44-2
100T44
3.625
2100
1,800
6,100
7,600
48,800
110T44-2
110T44
4.000
1850
2,600
9,100
11,400
72,800
120T44-2
120T44
4.500
1750
3,800
13,000
16,200
104,000
130T44-2
130T44
5.250
1450
5,400
18,400
23,000
147,200
140T44-2
140T44
6.500
1300
rectangular keys.
24
19
...
...
...
...
...
...
...
...
...
29
23
19
...
...
...
...
...
...
...
...
...
27
22
19
...
...
...
...
...
...
...
...
30
25
22
17
...
...
...
...
...
...
...
...
29
24
19
16
...
...
...
...
...
...
...
31
26
21
17
...
...
...
...
...
...
...
...
30
24
20
17
15
...
...
...
...
...
...
...
27
22
19
17
15
...
...
...
...
...
...
31
25
22
19
17
16
...
...
...
...
...
...
27
24
21
19
17
...
...
...
...
...
...
30
25
22
20
18
17
...
...
...
...
...
...
29
25
23
20
19
...
...
...
...
...
...
...
28
25
23
21
Outside Diameter
Pitch Diameter
3V
5V
8V
3.10
3.70
4.30
4.90
5.60
6.10
7.00
8.00
9.20
10.10
11.00
12.60
14.40
7.10
7.10
7.10
7.10
7.10
7.10
7.50
8.50
9.70
10.60
11.50
13.10
14.90
12.50
12.50
12.50
12.50
12.50
12.50
12.50
12.50
12.50
12.50
12.50
13.90
15.70
3.13
3.73
4.33
4.93
5.63
6.13
7.03
8.03
9.23
10.13
11.03
12.63
14.43
5.40
5.40
5.40
5.40
5.71
6.21
7.11
8.11
9.31
10.21
11.11
12.71
14.51
9.00
9.00
9.00
9.00
9.00
9.00
9.00
9.00
9.66
10.56
11.46
13.06
14.86
13.00
13.00
13.00
13.00
13.00
13.00
13.00
13.00
13.00
13.00
13.00
13.40
15.20
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
21.00
(421-110) 21
Type
T45
T50
COUPLING
= T45/T50 ASSEMBLY
PLUS
G52
COUPLING
= T45/G52 ASSEMBLY
Type
T42
T50
COUPLING
= T42/T50 ASSEMBLY
PLUS
G52
COUPLING
= T42/G52 ASSEMBLY
Either the T45 or T42 coupling can be used with a T50 or G52 coupling on the opposite end of the floating shaft to achieve different
operational characteristics or preferences for grid or gear couplings.
Contact Falks Coupling Inquiry Department or Coupling Engineering for selection assistance.
1030T42
1040T42
1050T42
1060T42
1070T42
1080T42
1090T42
1100T42
1010G
1010G
1010G
1015G
1015G
1020G
1025G
1030G
1110T42
1120T42
1130T42
1140T42
1150T42
1160T42
1170T42
1030G
1035G
1040G
1050G
1050G
1060G
1070G
22 (421-110)
DRIVING
SHAFT
SENSOR
TARGET
1.00
CONTROL BOX
SENSOR
HEAD
T41 HUB
CABLE TO
MOTOR
JAM NUT
Overhanging Hubs
When the distance between shaft ends is greater than the
Coupling gap or when the coupling or clutch hub length is
greater than the usable shaft length, overhang one or both hubs.
For Type T41, if this results in less than one shaft diameter of hub
engagement, check key stresses or use a semi-standard long T
hub listed in Table 23, Page 42 or submit application details to
the Falk
CAUTION: The effect of open keyways on coupling or clutch
balance should always be considered.
(421-110) 23
10
8
6
5
4
336
2
2
3
10
8
6
5
4
2
1
10
880
6
5
4
ip
Sl
us d
uo te
in it
nt erm
Co P
ip
Sl
us d
uo te
in it
nt erm
Co P
3
2
10
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
1
2
3
1480
10
8
3
2
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
8
6
5
4
3
2400
2
2
10
8
ip
Sl
us d
uo te
in it
nt erm
Co P
ip
Sl
us d
uo te
in it
nt erm
Co P
6
5
4
50
10
3 4
2
3
6
5
4
3
2
60
10
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
24 (421-110)
80
10
3 4
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
2
3
ip
Sl
us d
uo te
in it
nt erm
Co P
10
8
6
5
4
3
6
5
4
3
100
120
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
Automatic cutout switch required.
30 seconds slip permitted if followed by 10 minutes non-slip.
60 seconds slip permitted if followed by 10 minutes non-slip.
3 4
10
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
Automatic cutout switch required.
33 seconds slip permitted if followed by 11 minutes non-slip.
66 seconds slip permitted if followed by 11 minutes non-slip.
6
5
4
6
5
4
ip
Sl
us d
uo te
in it
nt erm
Co P
3
2
390
10
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
2
2
ip
Sl
us d
uo te
in it
nt erm
Co P
3
2
2
3
10
8
ip
Sl
us d
uo te
in it
nt erm
Co P
6
5
4
3
1
2
3
10
8
6
5
4
10
8
660
10
10
8
6
5
4
32800
2
18000
3 4
10800
ip
Sl
us d
uo te
in it
nt erm
Co P
4
3
10
8
10
2
3
4
1
ip
Sl
us d
uo te
in it
nt erm
Co P
10
8
6
5
4160
6
5
4
3
2
1800
1200
10
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
10
3 4
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
10
2
1
2
3
ip
Sl
us d
uo te
in it
nt erm
Co P
10
8
6
5
4
104000
8
6
5
4
3
2
3
ip
Sl
us d
uo te
in it
nt erm
Co P
72800
6
5
4
3
3
2600
2
APPLIES ONLY WHEN T41 OR T44
HUB IS MOUNTED ON DRIVING SHAFT
2
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
Automatic cutout switch required.
60 seconds slip permitted if followed by 20 minutes non-slip.
120 seconds slip permitted if followed by 20 minutes non-slip.
10
1
2
3
3800
10
3 4
1
2
3
2
3
ip
Sl
us d
uo te
in it
nt erm
Co P
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
1
1
2
3
2
3
6
5
4
36000
3
3 4 5 6 8100
2 3 4 5 6 81000
2
SPEED (RPM)
Automatic cutout switch required.
106 seconds slip permitted if followed by 35 minutes non-slip.
212 seconds slip permitted if followed by 35 minutes non-slip.
10
26 (421-110)
3 4
3 4
1
10
8
6
5
4
3
26000
2
10
2 3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
Automatic cutout switch required.
92 seconds slip permitted if followed by 31 minutes non-slip.
184 seconds slip permitted if followed by 31 minutes non-slip.
10
8
6
5
392000
3
10
8
6
49000
4
3
1
2
3
208000
ip
Sl
us d
uo te
in it
nt erm
Co P
10
8
ip
Sl
us d
uo te
in it
nt erm
Co P
288000
2
6
5
4
3 4
SIZE 170T41
SIZE 160T41
10
8
ip
Sl
us d
uo te
in it
nt erm
Co P
147200
10
8
6
5
4
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
10
8
6
5
4
SIZE 150T41
5400
10
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
Automatic cutout switch required.
110 seconds slip permitted if followed by 37 minutes non-slip.
220 seconds slip permitted if followed by 37 minutes non-slip.
10
3 4
1
2
3
SIZE 180T41
SIZE 190T41
10
8
10
1
2
ip
Sl
us d
uo te
in it
nt erm
Co P
4
3
3
10
8
67000
5
4
3
2
ip
Sl
us d
uo te
in it
nt erm
Co P
6
536000
720000
6
5
4
6
5
4
3
2
2
APPLIES ONLY WHEN T41 OR T44
HUB IS MOUNTED ON DRIVING SHAFT
10
2
3
90000
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
10
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
SIZE 200T41
10
8
6
5
4
3
2
960000
8
6
5
4
ip
Sl
us d
uo te
in it
nt erm
Co P
1
3
120000
10
1
2
3
3 4 5 6 8100
2 3 4 5 6 81000
SPEED (RPM)
3 4
(421-110) 27
Type
T50
GASKET
J
MINIMUM CLEARANCE
FOR GRID REMOVAL
M
COVER
LUBE PLUGS
GRID
A
DD
BE
GAP
C
SD
SB
FLANGED HUB
PILOT HUB
GAP
FLANGED HUB
ELASTOMER GAP
DISC FOR VERTICAL
APPLICATIONS - LOWER
COUPLING ONLY
SIZE
H
Max Bore
Torque
(Flanged Min
Rating
Hub) l Bore n
(lb-in)
1030T
1,320
1050T
3,850
1070T
8,800
1080T
18,150
1090T
33,000
1100T
55,550
1110T
82,500
1120T
121,000
1130T
176,000
1140T
253,000
1150T
352,000
1160T
495,000
1170T
660,000
1180T
915,200
1190T 1,210,000
1200T 1,650,000
1.375
1.875
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250
8.000
9.000
10.000
11.000
12.000
13.000
.500
.500
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
4.250
4.750
5.250
6.000
6.000
7.000
Wt Added
Per Inch of
Pilot Wt Per Length of Lube Wt
Per
Hub Cplg No SD Dia
Bore Bore-lb Between Cplg-lb
Hubs
1.06
1.44
1.94
2.44
2.94
3.62
4.00
4.62
5.25
5.62
6.38
7.88
7.88
8.88
9.88
10.88
8.6
19.5
34.4
58.2
82
139
184
216
309
462
610
840
1144
1583
1979
2657
0.279
0.500
0.889
1.390
2.000
3.130
3.770
5.010
6.430
7.350
9.390
14.200
14.200
18.000
22.200
26.900
28 (421-110)
.09
.15
.25
.38
.56
.94
1.12
1.62
2.0
2.5
4.3
6.2
7.7
8.3
9.7
12.4
DIMENSIONS INCHES
BE
Min
DD
SB
SD
Gap
4.56
6.20
7.20
8.60
9.64
11.26
12.76
12.88
14.38
16.50
18.80
21.60
23.80
26.20
27.90
30.80
6.38
7.66
8.38
10.82
11.56
14.65
15.38
17.82
18.22
18.98
21.62
23.10
24.50
26.50
28.00
29.30
1.88
2.38
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
7.20
7.80
8.50
9.40
10.20
11.00
1.94
2.62
3.44
4.12
4.88
5.59
6.31
7.06
8.56
10.00
10.68
12.00
14.00
15.50
17.20
19.60
3.30
4.14
4.98
6.10
7.10
8.32
9.66
7.06
8.56
10.00
10.60
12.00
14.00
15.50
17.20
19.60
3.18
4.12
5.08
6.15
6.92
8.20
9.00
10.12
11.62
13.22
15.40
17.40
19.46
21.90
23.60
26.10
1.98
2.33
2.56
3.38
3.63
4.62
4.81
5.76
5.88
6.14
6.98
7.46
7.92
8.94
9.52
9.92
3.06
3.70
4.06
5.28
5.66
7.14
7.50
8.66
8.86
9.24
10.56
11.30
12.00
13.00
13.76
14.40
1.06
1.42
1.96
2.05
2.30
2.73
2.91
3.29
3.73
4.48
4.00
4.40
4.90
5.56
6.20
6.80
1.06
1.44
1.94
2.44
2.94
3.62
4.00
4.62
5.25
5.62
6.38
7.88
7.88
8.88
9.88
10.88
1.12
1.50
2.00
2.50
3.00
3.75
4.12
4.75
5.38
5.75
6.50
8.00
8.00
9.00
10.00
11.00
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
.250
.250
.250
.250
Type T50
Floating Shaft/Selections
Introduction Floating shaft diameters have been preselected
to transmit the coupling torque and need only to be checked for
allowable speed.
For Speeds over 540 rpm Trace right from the shaft
diameter determined along the diagonal line to the point of
intersection with the required vertical operating speed line.
Trace right along the horizontal line to the right and read the
maximum allowable shaft length.
247
234
221
199
2000
3000
4000
5000
6000
300
1750
RPM
250
151
4 1/8
3 3/4
135
1500
1170
RPM
170
158
1000
BALANCING OF
SHAFT REQUIRED
200
150
DIA.
RPM
181
800
11
10
9
8
6 1/2
5 3/4
5 3/8
4 3/4
187
259
SHAFT
DIA.
(IN.)
3
123
2 1/2
110
MAX. SHAFT
LENGTH INCHES
(UNDER 540 RPM)
100
96
1 1/2
90
1 1/8
83
(78
80
DIA.)
70
60
50
1170
RPM
40
1750
RPM
35
BALANCING
NORMALLY NOT
REQUIRED
30
25
540 600
800
1000
1500
2000
3000
4000
5000
20
6000
(421-110) 29
Capabilities
The Falk Steelflex Disc Brake Coupling with Caliper Brake System
has an assigned coupling brake rating range of 8 to 12,500
ft-lbs.
Operation
The hydraulic brake system is actuated by turning on its electric
motor. The motor drives a gear pump which produces a flow of
oil between pump and solenoid directional control valve. When
the solenoid directional control valve is energized, oil pressure
rises in the caliper brake compressing the belleville springs to
apply the brake.
MOTOR
6.12
(APPROX.)
5.75
RELIEF VALVE
(SET AT 2000 PSI)
LIQUID FILLED
PRESSURE GAUGE
(0-3000 PSI)
FILLER/BREATHER PLUG
RESERVOIR
2-WAY CONTROL
VALVE
DRAIN PLUG
30 (421-110)
12.70
(APPROX.)
Type T63
Disc Brake/Dimensions Inches
KB
KB
CALIPER PROFILE
SIZE 90-120T
KB
CUSTOMER
MOUNTING PLATE
KA
CALIPER PROFILE
SIZE 50-80T
T10
COVER
T63
HUB
KA
CALIPER PROFILE
SIZE 130-160T
P
GAP
C
T
HUB
LUBE
PLUGS
G
DIMENSIONS INCHES
Cplg
Brake
Rating
(lb-ft)
Brake Disc
Dia x
Thickness
(E x F) Q
Allow
Speed
rpm
Max
Bore t
Min
Bore n
Cplg Wt With
No Bore &
No Disc-lb
Lube
Wt
lb
Gap
20T
30T
40T
50T
60T
70T
80T
90T
100T
110T
120T
130T
140T
150T
160T
8
26
48
87
154
244
470
800
1400
2100
3200
4500
6500
9000
12500
8 x .25
10 x .25
10 x .25
10 x .25
12 x .25
12 x .25
12 x .25
16 x .50
16 x .50
18 x .50
20 x .50
22 x .50
24 x .50
30 x .50
36 x .50
4500
4500
4500
4150
3800
3250
2850
2700
2400
2250
2025
1800
1650
1500
1350
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250
8.000
9.000
.500
.500
.500
.500
.750
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
4.250
4.750
5.63
7.29
9.40
14.00
21.10
27.20
43.60
62.60
105.20
143.00
203.00
290.00
407.00
558.00
741.00
.06
.09
.12
.15
.19
.25
.38
.56
.94
1.12
1.62
2.00
2.50
4.20
6.20
4.00
4.38
4.62
5.44
5.94
6.38
7.62
8.38
9.88
10.62
12.12
13.62
15.12
17.84
19.74
1.88
1.88
2.00
2.38
2.50
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
7.20
7.80
1.56
1.94
2.25
2.62
3.00
3.44
4.12
4.88
5.59
6.31
7.06
8.56
10.00
10.60
12.00
2.36
2.36
2.36
2.36
3.49
3.49
3.49
3.46
4.69
5.75
5.91
6.04
6.29
7.08
7.68
2.62
2.69
2.75
3.12
3.62
3.75
4.56
4.81
6.12
6.36
7.54
7.68
7.92
10.68
10.98
2.812
3.125
3.875
4.250
4.938
5.250
6.000
7.062
8.500
9.500
10.875
11.625
13.000
14.500
15.750
2.38
2.38
2.38
2.38
3.47
3.47
3.47
3.47
4.69
5.75
5.88
6.00
6.25
7.20
7.80
.46
.46
.46
.52
.60
.60
.71
1.06
1.16
1.16
1.30
1.40
1.50
1.24
1.24
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
SIZE
SIZE
H
20T
30T
40T
50T
60T
70T
80T
90T
100T
110T
120T
130T
140T
150T
160T
t Couplings will be furnished for INTERFERENCE FIT without a set screw. Clearance fit and/or hubs with set screws are not recommended. Falk standards apply unless other wise
specified. Maximum bores listed are based on recommended keys shown in Table 13, Page 36. For other maximum bore-key combinations that can be manufactured to order,
refer to Table 15 on Page 37.
Q Refer to Falk for discs with dimensions other than shown.
(421-110) 31
Type T63
Disc Brake Caliper System/Dimensions Inches
CONDUIT
BOX
5.25
5.00
5.60
2.50
16.06 (APPROX.)
0.34 WIDE SLOTS
27.43 (APPROX.)
LIQUID FILLED
PRESSURE GAUGE
0.250 NPT
CUSTOMER
CONNECTION
CONTROL
VALUE
RESERVOIR
FILLER
BREATHER
MOTOR
14.12
(APPROX.)
6.10
3.50
RELIEF
VALVE
3.00
2.75
0.75
4.50
Caliper Brake s
CPLG
SIZE
Brand
Model No. t
DIMENSIONS INCHES
Torque (lb-ft)
Min
20T
30T
40T
50T
60T
70T
80T
90T
100T
110T
120T
130T
140T
150T
160T
Max
KA
KB
6.22
7.22
7.22
7.22
11.50
11.50
12.50
13.50
13.25
14.25
18.18
21.22
3.80
4.93
4.93
4.93
5.46
6.69
7.75
7.91
8.54
8.79
9.68
10.28
MICO, Inc.
Meritor
02-515-002
02-515-004
02-515-008
02-515-006
02-530-306
02-530-628
02-530-628
02-530-600
PD1591 15 1
PD1591 15 1
SCL25 15 4
SCL25 15 4
46
116
350
466
517
534
612
1,389
1,625
1,792
3,438
4,188
90
180
410
570
1,074
1,830
2,100
3,290
6,094
6,719
17,188
20,938
t These brakes use hydraulic oil (NOT brake fluid). Any high grade hydraulic oil with viscosities of 150 SSU-350 SSU @ 100F is suitable.
s
Maximum torque shown is rating with new pads. Minimum torque shown is rating at point when caliper requires adjustment for pad wear.
Dimension KB is to caliper mounting surface for Coupling Sizes 50T thru 120T, and to caliper edge for Coupling Sizes 130T and larger.
32 (421-110)
Type
T70
MINIMUM CLEARANCE
FOR GRID REMOVAL
M
COVER
LUBE PLUGS
GRID
SIZES 1120-1140
GAP
C
D
DD
FLANGED
HUB
T HUB
B
Torque
Rating
(lb-in)
Allow
Speed
rpm
1030T
1050T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1,320
3,850
8,800
18,150
33,000
55,550
82,500
121,000
176,000
253,000
10,000
9,000
8,200
7,100
6,000
4,900
4,500
4,000
3,600
3,300
SIZE
Max
Bore l
1.375
1.875
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.250 t
DIMENSIONS INCHES
Min
Bore n
Cplg Wt
With No
Bore-lb
Lube
Wt
lb
DD
Gap
.500
.500
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
8.6
19.5
34.4
58.2
82
139
184
216
309
462
.09
.15
.25
.38
.56
.94
1.12
1.62
2.0
2.5
4.56
6.20
7.20
8.60
9.64
11.26
12.76
12.88
14.38
16.50
3.88
4.88
6.12
7.12
7.88
9.69
10.19
12.00
13.00
14.75
1.88
2.38
3.00
3.50
3.88
4.75
5.00
5.88
6.38
7.25
1.94
2.62
3.44
4.12
4.88
4.59
6.31
7.06
8.56
10.00
3.30
4.14
4.98
6.10
7.10
8.32
9.66
7.06
8.56
10.00
3.18
4.12
5.08
6.15
6.92
8.20
9.00
10.12
11.62
13.22
1.98
2.33
2.56
3.38
3.63
4.62
4.81
5.76
5.88
6.14
3.06
3.70
4.06
5.28
5.66
7.14
7.50
8.66
8.86
9.24
1.06
1.42
1.96
2.05
2.30
2.73
2.91
3.29
3.73
4.48
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
(421-110) 33
Type T90
Engine Flywheel Adapter/Dimensions Inches
COVER
GRID
G - (NO. & SIZE OF HOLES)
AF
GAP
BC
ADAPTER
DIMENSIONS INCHES
Adapter
Cplg Wt
Min
No Bore in WR2
Bore
T Hub
(lb-in2)
n
lb
Allow
Speed
rpm
Max Bore
Sq Key l
3500
5500
8000
3600
3600
3600
1.875
2.125
2.500
.500
.750
.750
18
23
29
1050T
1060T
1070T
3500
5500
8000
3600
3600
3600
1.875
2.125
2.500
.500
.750
.750
1050T
1060T
1070T
1080T
3500
5500
8000
16500
3600
3600
3600
3600
1.875
2.125
2.500
3.000
.500
.750
.750
1.062
CPLG
SIZE H
Clutch
Dia
AF
+.000
.005
BC
6.5
8.500
7.875
6-.344
.375
.375
.375
1050T
1060T
1070T
7.5
9.500
8.750
8-.344
.375
.375
.375
10.375
9.625
6-.406
.375
.375
.375
.500
Torque
Rating
(lb-in)
Gap
85
106
130
5.44
5.94
6.38
5.58
5.94
6.94
2.38
2.50
3.00
2.62
3.00
3.44
3.12
3.62
3.75
3.07
3.31
3.81
.125
.125
.125
20
24
30
115
136
160
5.44
5.94
6.38
5.58
5.94
6.94
2.38
2.50
3.00
2.62
3.00
3.44
3.12
3.62
3.75
3.07
3.31
3.81
.125
.125
.125
21
26
32
48
151
172
196
332
5.44
5.94
6.38
7.62
5.58
5.94
6.94
8.07
2.38
2.50
3.00
3.50
2.62
3.00
3.44
4.12
3.12
3.62
3.75
4.56
3.07
3.31
3.81
4.44
.125
.125
.125
.125
10
12.375 11.625
8-.406
.500
1080T
16500
3600
3.000
1.062
53
494
7.62
8.07
3.50
4.12
4.56
4.44
.125
11.5
13.875 13.125
8-.406
.500
1090T
30000
3600
3.500
1.062
74
820
8.38
8.95
3.88
4.88
4.81
4.94
.125
14
18.375 17.250
8-.531
.650
.750
1100T
1110T
50500
75000
2440
2250
4.000
4.500
1.625
1.625
133
162
2702
3297
9.88 10.90
10.62 11.50
4.75
5.00
5.59
6.31
6.12
6.36
5.96
6.31
.188
.188
16
20.375 19.250
8-.531
.650
.750
1100T
1110T
50500
75000
2440
2250
4.000
4.500
1.625
1.625
145
175
3750
4507
9.88 10.90
10.62 11.50
4.75
5.00
5.59
6.31
6.12
6.36
5.96
6.31
.188
.188
18
22.500 21.375
6-.656
.750
.750
.900
1110T
1120T
1130T
75000
110000
160000
2250
2025
1800
4.500
5.000
6.000
1.625
2.375
2.625
190
243
331
6243
7165
9737
10.62 11.50
12.12 13.43
13.62 14.69
5.00
5.88
6.38
6.31
7.06
8.56
6.36
7.54
7.68
6.31
7.30
8.06
.188
.250
.250
21
.900
1.000
1.000
1130T
1140T
1150T
160000
230000
320000
1800
1650
1500
6.000
2.625
7.250 Q 2.625
8.000 Q 4.250
371
478
608
15560
19609
25878
13.62 14.69
15.12 16.53
17.84 16.56
8.06
9.03
9.11
.250
.250
.250
24
.900
1.000
1.000
1130T
1140T
1150T
160000
230000
320000
1800
1650
1500
6.000
2.625
7.250 Q 2.625
8.000 Q 4.250
397
507
638
20463
25058
31353
13.62 14.69
15.12 16.53
17.84 16.56
8.06
9.03
9.11
.250
.250
.250
1.000
1.250
1160T
1170T
450000
600000
1350
1225
...
...
19.76 17.85
22.32 19.50
9.80
10.75
.250
.250
Machined as Required
Assembly
9.000 Q
10.000 Q
4.750
5.250
656 s
902 s
For total coupling weight add [ .2223 x (AF2 - U2) x T ] to value shown. Size 1160 U = 15.50, Size 1170 U = 17.25.
34 (421-110)
Type
T10/G82
REGISTER DETAIL
SIZES 1080, 1090 & 1100G
T GRID
COVER
PROFILE
T10 COVER
CENTER PLATE
G82 RIGID HUB
T HUB
A
SIZES 1110 - 1140T
GAP
C
F
A
BE
GAP
BETWEEN SHAFT ENDS
L
FA
AA
SD
SHAFT
COVER
FASTENERS
T10
CPLG
SIZE
H
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
G82
CPLG
SIZE
H
Torque
Allow
Rating
Speed
(lb-in)
rpm
1035G
82,500
1040G 121,000
1045G 176,000
1050G 253,000
1055G 352,000
1060G 495,000
1070G 660,000
1080G 915,200
1090G 1,210,000
1100G 1,650,000
2250
2025
1800
1650
1500
1350
1225
1100
1050
900
T10
Hub
4.500
5.000
6.000
7.250
8.000
9.000
10.000
11.000
12.000
13.000
5.875
7.250
8.125
9.000
10.000
11.000
13.000
13.000
14.250
15.000
Min
Bore n
1.625
2.375
2.625
2.625
4.250
4.750
5.250
6.000
6.000
7.000
2.000
2.500
3.000
3.500
4.000
4.500
5.000
4.000
4.500
5.000
275
404
576
842
1120
1421
2167
2894
3871
4970
4.50
5.56
8.00
11.7
14.2
18.0
22.2
26.9
32.0
37.6
FLANGE
FASTENERS
Cplg Wt Wt
With Added
No Per Inch Lube
Bore & of SD Dia Wt
lb A
No
G82 T10 G82 Shaft Between
Hubs
Hub Hub Hub
lb
Max
Bore l
H H
LUBE
PLUGS
1.12 10.62
1.62 12.12
2.00 13.62
2.50 15.12
4.30 17.84
6.20 19.74
7.70 22.30
8.30 24.80
9.70 26.60
12.40 29.80
Flange
Fasteners
DIMENSIONS INCHES
BE
Gap
Min Max
9.41
10.99
12.09
13.70
14.65
15.91
18.08
20.09
21.95
23.99
12 5.00 6.31
14 5.88 7.06
15 6.38 8.56
16 7.25 10.00
16 7.20 10.60
18 7.80 12.00
20 8.50 14.00
26 9.40 15.50
28 10.20 17.20
30 11.00 19.60
.10
.16
.16
.20
.20
.26
.33
.32
.32
.36
...
...
...
...
15.37
17.18
19.18
21.84
23.93
26.00
1.12
1.12
1.12
1.50
1.50
1.00
1.12
1.24
1.50
1.75
6.36
7.54
7.68
7.92
10.68
10.98
11.98
12.64
12.80
14.00
4.02
4.54
5.14
5.80
6.80
7.34
8.67
9.80
10.86
12.02
AA FA t
11.00
12.50
13.62
15.31
16.75
18.00
20.75
23.25
26.00
28.00
8.32
9.66
10.79
12.04
13.16
14.41
16.73
17.75
20.00
20.88
SD
No. Per
Flange Dia
T G82
& Inches
Hub Hub Grade
4.500 .188
5.000 .250
6.000 .250
7.250 .250
8.000 .250
9.000 .250
10.000 .250
11.000 .250
12.000 .250
13.000 .250
.200
.320
.320
.400
.400
.520
.660
.640
.640
.720
8,Gr 8
8,Gr 8
10,Gr 8
8,Gr 8
14,Gr 8
14,Gr 8
16,Gr 8
16,Gr 5
18,Gr 5
18,Gr 5
.750
.750
.750
.875
.875
.875
1.000
1.125
1.250
1.250
t Dimension FA is for an as-cast, unmachined surface for Sizes 1180, 1190 & 1200.
(421-110) 35
Engineering Data
TABLE 13 Recommended Commercial Keys for Bores with One Key Inches & Millimeters
INCHES (Per ANSI B17.1 Standard)
Shaft Dia
Over
Through
.438
.562
.875
1.250
1.375
.562
.875
1.250
1.375
1.750
6
8
10
12
17
22
30
8
10
12
17
22
30
38
Shaft Dia
Key
Over
Through
.125 x .125
.188 x .188
.250 x .250
.312 x .312
.375 x .375
1.750
2.250
2.750
3.250
3.750
2.250
2.750
3.250
3.750
4.500
2x2
3x3
4x4
5x5
6x6
8x7
10 x 8
38
44
50
58
65
75
85
44
50
58
65
75
85
95
Shaft Dia
Key
.500 x .500
.625 x .625
.750 x .750
.875 x .875
1.000 x 1.000
Over
Through
4.500
5.500
6.500
7.500
9.000
5.500
6.500
7.500
9.000
11.000
110
130
150
170
200
230
260
Shaft Dia
Key
Key
Over
Through
1.250 x 1.250
1.500 x 1.500
1.750 x 1.500
2.000 x 1.500
2.500 x 1.750
11.000
13.000
15.000
18.000
...
13.000
15.000
18.000
20.000
...
3.000 x 2.000
3.500 x 2.500
4.000 x 3.000
5.000 x 3.500.
...
28 x 16
32 x 18
36 x 20
40 x 22
45 x 25
50 x 28
56 x 32
260
290
330
380
440
...
...
290
330
380
440
500
...
...
63 x 32
70 x 36
80 x 40
90 x 45
100 x 50
...
...
95
110
130
150
170
200
230
TABLE 14 Shaft Diameters & Ratings for NEMA 60 Hertz & 50 Hertz Metric Motors
NEMA 60 HERTZ MOTORS (hp)
Frame Size
Shaft Dia - Inches
T Frames
143 145 182 184 213 215 254 256 284 286 324 326 364 365 404 405 444 445 284 286 324 326 364 365 404 405 444 445
.88
.88
Drip Proof
Enclosed
Drip Proof
1200 RPM
& Enclosed
Drip Proof
900 RPM & Enclosed
TS Frames
1.13 1.13 1.38 1.38 1.63 1.63 1.88 1.88 2.13 2.13 2.38 2.38 2.88 2.88 3.38 3.38 1.63 1.63 1.88 1.88 1.88 1.88 2.13 2.13 2.38 2.38
5
3
1 1 1/2-2 3
1 1 1/2-2 3
7 1/2 10 15
5 7 1/2 10
20
15
25
20
30
25
40
30
50
40
60
50
75
60
30
25
40
30
50
40
60
50
75
60
7 1/2 10
7 1/2 10
15
15
20
20
25
25
30
30
40
40
50
50
60
60
75
75
25
25
30
30
40
40
50
50
60
60
75
75
7 1/2 10
15
20
25
30
40
50
60
75
100 125
15
20
25
30
40
50
60
75
100 125
7 1/2 10
15
20
25
30
40
50
60
75
10
15
20
25
30
40
50
60
75
5
5
3 /4
1 1/ 2
1 /2
3/4
1 1/2
100
100
80
90S
90L
100L
112M
132S
132M
160M
160L
180M
200M/L
225S
225M
250S
250M
280S
280M
48
55
55
60
55
60
60, 65
70
60, 65
70
65, 75
80
65, 75
80
22
...
30
37
45
45
55
55
75
75
90
90
110
15
18,5
22
30
37
45
45
55
55
75
75
90
90
110
7,5
11
...
15
18,5
22
30
30
37
37
45
45
50
55
75
4
5,5
7,5
...
11
15
18,5
22
30
30
37
37
45
45
55
Shaft Dia mm
19
24
24
28
28
38
38
42
42
48
3000 RPM
0,75
1,10
1,5
2,2
3,0
5,5
7,5
...
11
15
18,5
1500 RPM
0,55
0,75
1,1
1,5
2,2
3,0
5,5
7,5
11
1000 RPM
0,37
0,55
0,75
1,1
1,5
2,2
4
5,5
750 RPM
0,18
0,25
0,37
0,55
0,75
1,1
1,5
2,2
36 (421-110)
180L
SD
SD
Engineering Data
TABLE 15 Type T Hub & Flanged Hub Bore Ranges with Square & Rectangular Keys
Millimeters s
Inches
SIZE
H
Min
Bore
n
20/1020T
.500
30/1030T
.500
40/1040T
.500
50/1050T
.500
60/1060T
.750
70/1070T
.750
80/1080T 1.062
90/1090T 1.062
100/1100T 1.625
110/1110T 1.625
120/1120T 2.375
130/1130T 2.625
140/1140T 2.625
150/1150T 4.250
160/1160T 4.750
1170T 5.250
1180T 6.000
1190T 6.000
1200T 7.000
1210T 7.000
1220T 8.000
1230T 8.000
1240T 10.000
1250T 10.000
1260T 10.000
Y=X
Max
Bore l
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.000
7.500
8.500
9.750
10.750
11.750
12.750
13.750
14.750
15.750
16.750
18.000
19.500
.250
.312
.375
.500
.500
.625
.750
.875
1.000
1.000
1.250
1.500
1.750
1.750
2.000
2.500
2.500
3.000
3.000
3.500
3.500
4.000
4.000
4.000
5.000
Y=W/2 Q
Y=X
X
Max
Bore l
.125
.156
.187
.250
.250
.312
.375
.437
.500
.500
.625
.750
.875
.875
1.000
1.250
1.250
1.500
1.500
1.750
1.750
2.000
2.000
2.000
2.500
1.187
1.437
1.750
2.000
2.250
2.687
3.250
3.750
4.250
4.625
5.375
6.500
7.250
8.000
9.000
10.000
11.000
12.000
13.000
14.000
15.000
16.000
17.000
18.500
20.000
.250
.375
.375
.500
.500
.625
.750
.875
1.000
1.250
1.250
1.500
1.750
2.000
2.000
2.500
2.500
3.000
3.000
3.500
3.500
4.000
4.000
5.000
5.000
Max
Bore l
.093
.125
.125
.187
.187
.218
.250
.312
.375
.437
.437
.500
.750
.750
.750
.875
.875
1.000
1.000
1.250
1.250
1.500
1.500
1.750
1.750
1.250
1.562
1.750
2.125
2.375
2.875
3.375
3.875
4.500
5.000
5.750
6.500
7.750
...
...
...
...
...
...
...
...
...
...
...
...
.250
.375
.375
.500
.625
.750
.875
1.000
1.000
1.250
1.500
1.500
2.000
...
...
...
...
...
...
...
...
...
...
...
...
For Two
Rectangular Keys
Y=X
Max
Bore l
.062
.062
.062
.125
.125
.125
.187
.250
.250
.250
.250
.250
.500
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
10.750
12.000
13.000
14.000
15.000
16.000
17.000
18.000
19.250
20.750
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1.750
1.750
2.000
2.500
2.500
2.500
3.000
3.000
3.500
3.500
Max Bore
Min Std Bore Int Fit per
Bore Fits per
Table 25
Table 25 w/Setscrew
Over Keyway
Y=X
X
Max.
Bore l
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
.875
.875
1.000
1.250
1.250
1.250
1.500
1.500
1.750
1.750
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
11.000
12.250
13.250
14.250
15.250
16.250
17.250
18.250
19.750
21.250
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1.750
2.000
2.000
2.500
2.500
3.000
3.000
3.000
3.500
3.500
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
.750
.750
.750
.875
.875
1.000
1.000
1.000
1.250
1.250
13
13
13
13
20
20
27
27
42
42
61
67
67
108
121
134
153
153
178
178
178
254
254
28
35
43
50
56
67
80
95
110
120
140
170
200
215
240
280
300
336
360
390
420
450
480
24
30
38
45
50
60
75
90
100
110
120
150
180
190
215
240
260
290
320
350
380
410
440
Metric keyways and keyway radiuses will be furnished per ISO/R773 (DIN 6885/1) and Js9 width tolerances unless otherwise specified. P9 and D10 width tolerance can be
furnished on request. Refer to 427-140 for tolerances.
Shaded areas indicate maximum bores using standard recommended keys shown in Table 13.
t Unless otherwise specified, Sizes 1020 thru 1090 will be furnished for CLEARANCE FIT with a setscrew OVER the keyway and Sizes 1100 and larger will be furnished for
INTERFERENCE FIT without a setscrew. EXCEPTION: For Types T50 and T70, coupling hubs are normally furnished with an average INTERFERENCE FIT of .0005 per inch of
shaft diameter. Clearance fit and/or hubs with setscrews are not recommended.
Q Shaft keyway depth Y equals one-half of square key W. CHECK KEY STRESSES.
s Also applies to Hub Type T61, T63, T50 pilot hub and flanged hub of T50 and T70 type couplings.
With standard puller bolt holes per Tables 24 and 25, Page 42.
Consult Falk.
TABLE 16 Type T31& T35 Shaft Hub Bore Ranges with Square & Rectangular Keys
Inches
For One Square Key
SIZE
H
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
Min
Bore n
.500
.500
.500
.500
.750
.750
1.062
1.062
1.500
2.000
2.500
3.000
3.500
4.000
4.500
5.000
4.000
4.500
5.000
Max
Bore l
1.375
1.625
2.125
2.375
2.875
3.125
3.500
4.000
4.750
5.500
6.250
6.750
7.500
9.750
10.500
12.000
12.000
13.250
14.250
.312
.375
.500
.625
.750
.750
.875
1.000
1.250
1.250
1.500
1.750
2.000
2.000
2.500
3.000
3.000
3.500
3.500
Millimeters
For One Rectangular Key
Y=X
X
.156
.188
.250
.312
.375
.375
.438
.500
.625
.625
.750
.875
1.000
1.000
1.250
1.500
1.500
1.750
1.750
1.437
1.750
2.250
2.500
3.125
3.250
3.750
4.250
5.000
5.875
6.500
7.000
8.000
10.000
11.000
13.000
13.000
14.250
15.000
.375
.375
.500
.625
.750
.750
.875
1.000
1.250
1.500
1.500
1.750
2.000
2.500
2.500
3.000
3.000
3.500
3.500
Max Bore
Y=W/2 Q
Y=X
Max
Bore l
Min
Bore
Max
Bore l
.125
.125
.188
.218
.250
.250
.312
.375
.438
.500
.500
.750
.750
.875
.875
1.000
1.000
1.250
1.250
1.562
...
2.375
2.625
3.250
3.375
3.875
4.500
5.250
6.250
6.750
7.250
8.500
...
...
...
...
...
...
.375
...
.625
.625
.750
.875
1.000
1.000
1.250
1.500
1.750
1.750
2.000
...
...
...
...
...
...
.062
...
.125
.125
.125
.188
.250
.250
.250
.250
.625
.625
.500
...
...
...
...
...
...
13
13
13
13
20
20
27
27
39
51
64
77
89
102
115
127
102
116
127
With
Int Fit per
Puller
Std Bore Table 25
Fits Per w/Setscrew Holes Per
Tables 22
Over
Table 25
or 23
Keyway
35
43
56
67
80
85
95
110
130
150
170
190
210
270
290
340
340
380
400
30
38
50
60
76
80
90
100
120
140
165
180
200
230
260
290
310
340
365
35
43
56
67
80
85
88
100
120
140
160
175
200
250
280
330
340
380
400
SIZE
H
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
(421-110) 37
K
W
Engineering Data
X HUB
Y SHAFT
TABLE 17 T41 Hub Bore Ranges with Square and Rectangular Keys
Inches
SIZE
H
Millimeters
Max Bore
Y=X
Max
Bore l
Max
Bore l
Min
Bore
20T41
30T41
40T41
50T41
60T41
70T41
.500
.500
.500
.500
.750
.750
1.000
1.250
1.375
1.750
1.875
2.250
.250
.250
.312
.375
.500
.500
.125
.125
.156
.187
.250
.250
1.125
1.375
1.625
1.875
2.125
2.500
.250
.312
.375
.500
.500
.625
.062
.093
.062
.125
.125
.125
.125
.156
.187
.250
.250
.312
13
13
13
13
20
20
24
32
38
45
50
60
32
40
45
50
80T41
1.062
2.625
.625
.312
2.750
3.000
.625
.750
.125
.125
.312
.375
27
27
70
70
65
65
90T41
1.062
3.125
.750
.375
3.250
3.500
.750
.875
.125
.187
.375
.437
27
27
85
85
80
80
100T41
1.625
3.625
.875
.437
3.750
4.000
.875
1.000
.187
.250
.437
.500
42
42
100
100
90
90
110T41
120T41
1.625
2.375
4.000
4.500
1.000
1.000
.500
.500
4.500
5.000
1.000
1.250
.250
.250
.500
.625
42
61
110
120
100
110
130T41
2.625
5.250
1.250
.625
5.500
6.000
1.250
1.500
.250
.250
.625
.750
67
67
145
145
135
135
140T41
2.625
6.500
1.500
.750
150T41
4.250
6.750 t
1.750
.875
160T41
4.750
7.750 t
2.000
1.000
170T41
5.250
9.000 t
2.000
1.000
7.250 Q
7.000
7.500 Q
8.000 Q
8.500
9.000 Q
9.500
10.000 Q
1.750
1.750
1.750
2.000
2.000
2.000
2.500
2.500
.500
.750
.500
.375
.750
.500
.875
.500
.750
.750
.750
.750
.750
.750
.875
.875
67
108
108
108
121
121
134
134
180
190
190
190
225
225
250
250
165
180
180
180
200
200
230
230
180T41
6.000
10.250 t
2.500
1.250
11.000
2.500
.875
.875
153
290
260
190T41
6.000
11.000 t
2.500
1.250
12.000
3.000
1.000
1.000
153
320
285
200T41
7.000
12.125 t
3.000
1.500
13.000
3.000
1.000
1.000
178
340
310
H Refer to footnotes from Table 15 and to Page 5 for General Information and Reference Notes. Unless otherwise specified, Sizes 1020 thru 1090 will be furnished for CLEARANCE
FIT with a setscrew OVER the keyway and Sizes 1100 and larger will be furnished for INTERFERENCE FIT without a setscrew.
t Maximum bore with optional square key.
Q A special rectangular key is required.
Shaded areas indicate maximum bores using standard recommended keys shown in Table 13.
Interference fit is not recommended.
TABLE 18 Type G82 Hub (used on T10/G82 assemblies) Bore Ranges with Square &
Rectangular Keys
Inches
Millimeters
1035G
1040G
1045G
1050G
1055G
1060G
1070G
1080G
1090G
1100G
Min
Bore n
2.000
2.500
3.000
3.500
4.000
4.500
5.000
4.000
4.500
5.000
Y=X
Max
Bore l
5.875
6.750
7.625
8.750
9.750
10.500
12.000
13.000
14.250
15.000
1.500
1.750
1.750
2.000
2.000
2.500
3.000
3.000
3.500
3.500
38 (421-110)
Max Bore
Y=X
X
Max
Bore l
.750
.875
.875
1.000
1.000
1.250
1.500
1.500
1.750
1.750
6.500
7.250
8.125
9.000
10.000
11.000
13.000
13.250
15.000
15.500
1.500
1.750
2.000
2.000
2.500
2.500
3.000
3.000
3.500
3.500
.500
.750
.750
.750
.875
.875
1.000
1.000
1.250
1.250
Min
Bore
Std
Bore
Fits Per
Table 25
51
64
77
89
102
115
127
102
115
127
163
196
216
235
266
290
340
340
380
400
150
185
205
228
250
280
330
340
380
400
Engineering Data
L
SIZES 1150T
THRU 1200T s
TAPER
BUSHING
TAPER
BUSHING
T HUB
SHAFT HUB
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
Shaft Hub
Taper-Lock Bushing
Bushing
Number
...
1108
1108
1215
1615
2012
2525
3030
3030
3535
4040
4545
5050
5050
5050
7060
8065
8065
10085
Bore Q
Range
(Inches)
...
.500 to 1.125
.500 to 1.125
.500 to 1.250
.500 to 1.625
.500 to 2.000
.750 to 2.500
.938 to 3.000
.938 to 3.000
1.188 to 3.500
1.438 to 4.000
1.938 to 4.500
2.438 to 5.000
2.438 to 5.000
2.438 to 5.000
3.938 to 7.000
4.438 to 8.000
4.438 to 8.000
7.000 to 10.000
L
(Inches)
...
1.62
1.62
1.88
2.12
2.12
2.62
3.12
3.50
3.62
4.38
4.62
5.12
7.20
7.80
8.50
9.40
10.20
11.00
Bushing
Number
1108
1108
1310
1615
2012
2525
2525
3030
3535
4040
4545
5050
5050
6050
7060
8065
8065
10085
10085
Bore Q
Range
(Inches)
.500 to 1.125
.500 to 1.125
.500 to 1.375
.500 to 1.625
.500 to 2.000
.750 to 2.500
.750 to 2.500
.938 to 3.000
1.188 to 3.500
1.438 to 4.000
1.938 to 4.500
2.438 to 5.000
2.438 to 5.000
3.438 to 6.000
3.938 to 7.000
4.438 to 8.000
4.438 to 8.000
7.000 to 10.000
7.000 to 10.000
Torque
(lb-in)
460
1,300
2,200
3,850
6,500
8,800
11,300
24,000
48,800
77,300
110,000
126,000
126,000
282,000
416,000
456,000
456,000
869,000
869,000
B
(Inches)
1.38
1.62
2.12
2.38
2.88
3.12
3.50
4.00
3.56
4.10
4.70
5.30
6.00
6.80 s
7.34 s
8.67 s
9.80 s
10.86 s
12.00 s
Gear
Cplg
Rigid
Hub
Size
...
...
...
...
...
...
...
...
...
...
...
...
...
1055
1060
1070
1080
1090
1100
t Use straight bored hubs for shock load or reversing load applications or applications that require 1.75 or higher coupling service factors or refer to the Falk for selection, price
and delivery of special bushings. Refer to Falk for selection of taper-lock bushings for Type T50 and T70 couplings.
Q Bushings require shaft keyways as calculated in Table 13.
s
(421-110) 39
Engineering Data
TABLE 20 WR2 Values lb-in2
(WR2 values are based on hubs with no bore; seals, lube plugs, and gaskets are not considered)
Coupling Type
T31
COUPLING
SIZE
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
1210T
1220T
1230T
1240T
1250T
1260T
T10/G82 t
T35
WR2
T10
4.83
7.61
11.19
24.85
40.66
63.18
154
269
609
923
1,755
3,378
6,306
11,922
19,876
35,621
62,553
89,359
148,676
257,900
385,696
597,136
1,157,844
1,791,120
2,428,359
T20
5.32
7.99
11.99
25.76
41.16
61.68
148
272
608
930
1,611
3,568
6,431
11,243
20,597
35,625
Added Per
Inch of BE
Over
Minimum
WR 2
(Min BE)
9.8
15.3
31.8
62.0
132
175
396
805
1,756
2,726
5,341
8,563
14,871
30,740
43,610
84,639
135,817
222,003
319,363
0.18
0.42
0.76
1.40
2.38
4.06
8.37
16.2
27.2
45.4
70.9
153
283
237
394
789
1,197
1,856
3,306
WR2
WR 2
(Min BE)
Added Per
Inch of BE
Over
Minimum
7.3
11.5
21.5
43.4
86.4
119
275
537
1,183
1,825
3,548
5,970
10,588
21,331
31,773
60,130
99,185
155,681
234,019
0.18
0.42
0.76
1.40
2.38
4.06
8.37
16.2
27.2
45.4
70.9
153
283
237
394
789
1,197
1,856
3,306
Rigid
Hub
Size
1035G
1040G
1045G
1050G
1055G
1060G
1070G
1080G
1090G
1100G
T50
WR2
WR2
Added
Per
2
WR
Added Per Inch
2
WR
Inch of Length
of length of
(Without
of SD
(Each Coupling)
SD Diameter
Shaft)
Diameter
Between Hubs
Between Hubs
2,688
5,155
8,738
16,346
28,112
41,251
80,916
130,917
212,411
316,614
11.3
17.3
35.8
76.3
113
181
276
404
572
788
T70
14.8
0.043
14.8
61.7
0.14
61.7
144
346
603
1,424
2,384
2,734
4,854
9,575
10,390
31,150
51,140
88,040
125,920
204,240
0.44
1.08
2.24
5.46
7.95
14.1
23.1
30.2
49.3
113
113
181
276
404
144
346
603
1,424
2,383
2,733
4,852
9,572
Coupling Misalignment
RECOMMENDED INSTALLATION
MAXIMUM
Y
P
GAP
CPLG
SIZE
20/1020T
30/1030T
40/1040T
50/1050T
60/1060T
70/1070T
80/1080T
90/1090T
100/1100T
110/1110T
120/1120T
130/1130T
140/1140T
150/1150T
160/1160T
170/1170T
180/1180T
190/1190T
200/1200T
1210T
1220T
1230T
1240T
1250T
1260T
MAXIMUM
OPERATING
Parallel
Offset P
Angular
Inches s
(1/16)
X
Types
Types
T10, T20 Type Type Minus T10, T20 Type
Y
T31, T35 T70
T31, T35 T50 T70
T41, T63
T41, T63
Parallel Offset P
.006
.006
.006
.008
.008
.008
.008
.008
.010
.010
.011
.011
.011
.012
.012
.012
.015
.015
.015
.018
.018
.019
.019
.020
.020
....
.002
....
.002
....
.002
.002
.003
.003
.003
.003
.004
.004
.004
.005
.005
.005
.006
.006
....
....
....
....
....
....
...
.003
...
.004
...
.004
.004
.004
.005
.005
.006
.006
.006
.006
.006
.006
.008
.008
.008
...
...
...
...
...
...
.003
.003
.003
.004
.005
.005
.006
.007
.008
.009
.010
.012
.013
.016
.018
.020
.022
.024
.027
.029
.032
.035
.038
.042
.046
.012
.012
.012
.016
.016
.016
.016
.016
.020
.020
.022
.022
.022
.024
.024
.024
.030
.030
.030
.036
.036
.038
.038
.040
.040
...
.006
...
.008
...
.008
.008
.008
.010
.010
.011
.011
.011
.012
.012
.012
.015
.015
.015
...
...
...
...
...
...
NORMAL GAP
10%
Angular
()
X
minus
Y
All
Types
Except
T31
Type
T31
.010
.012
.013
.016
.018
.020
.024
.028
.033
.036
.040
.047
.053
.062
.070
.079
.089
.097
.107
.118
.129
.142
.154
.169
.183
.125
.125
.125
.125
.125
.125
.125
.125
.188
.188
.250
.250
.250
.250
.250
.250
.250
.250
.250
.500
.500
.500
.500
.500
.500
.188
.188
.188
.188
.188
.188
.188
.188
.250
.250
.375
.375
.375
.375
.375
.375
.375
.375
.375
...
...
...
...
...
...
40 (421-110)
Operating offset limits between Type T50 floating shaft assembly is a function of 1/4 and
distance between shaft ends.
Rexnord Industries, Inc. 1963, 2005.
Engineering Data
Mill Motor and Taper Bore Dimensions Inches
Standardized for AISE mill motors. Also
available for use on other tapered shaft
applications such as large pumps,
compressors and turbines.
ZH
ZC
ZE
ZD
GAP
SIDE
R
UH
BASIC
DIA.
KEYWAY
PARALLEL
TO BORE
UG
CPLG
SIZE
.12
.12
.31
.31
.31
2.625
2.625
3.500
3.500
3.500
1.437
1.750
.500 x .250
3.94
.94
3.00
.024
ZH
UG
UH
Keyway
ZC
ZD
ZE
+.XXX
.000
2
602
802
A,B & C
AC
1,2 & 4
1060T
1070T
1080T
1090T
1100T
603
604
803
804
...
1070T
1080T
1090T
1100T
.12
.38
.38
.38
3.000
4.000
4.000
4.000
1.635
2.000
.500 x .250
4.50
1.00
3.50
.029
606
806
AC
8 & 12
1080T
1090T
1100T
1110T
.12
.38
.38
.38
3.500
4.500
4.500
4.500
2.083
2.500
.500 x .250
5.12
1.12
4.00
.029
608
808
...
1090T
1100T
1110T
1120T
.12
.50
.50
.50
4.375
5.375
5.375
5.375
2.531
3.000
.750 x .250
5.75
1.25
14.50
.029
610
810
AC18
1100T
1110T
1120T
1130T
.12
.50
.50
.50
5.000
6.000
6.000
6.000
2.781
3.250
.750 x .250
5.88
1.38
4.50
.034
612
812
AC
25 & 30
1100T
1110T
1120T
1130T
1140T
.12
.12
.12
.12
.12
5.250
5.250
6.250
6.250
6.250
3.104
3.625
.750 x .250
6.50
1.50
5.00
.034
614
814
AC
40 & 50
1110T
1120T
1130T
1140T
.12
.12
.50
.50
5.875
5.875
6.750
6.750
3.729
4.250
1.000 x .375
6.62
1.62
5.00
.034
616
816
...
1120T
1130T
1140T
.12
.62
.62
6.500
8.000
8.000
4.052
4.625
1.250 x .375
7.25
1.75
5.50
.034
618
818
...
1130T
1140T
1150T
.12
.62
.62
7.000
8.500
8.500
4.375
5.000
4.994
4.989
1.250 x .500
7.31
7.25
7.20
1.31
6.00
5.94
5.89
.038
620
...
...
1140T
1150T
1160T
.25
.75
.75
8.750
9.750
9.750
5.172
5.826
5.740
5.802
1.500 x .750
8.03
7.20
7.80
1.75
6.28
5.45
6.05
.038
622
...
...
1140T
1150T
1160T
1170T
.25
.75
.75
.75
8.750
9.750
9.750
9.750
5.495
6.083
5.997
6.059
6.132
1.500 x .750
8.03
7.20
7.80
8.50
2.38
5.65
4.82
5.42
6.12
.038
...
1140T
1150T
1160T
1170T
1180T
1190T
.25
.75
.75
.75
.75
.75
8.750
9.750
9.750
9.750
9.750
9.750
6.037
6.625
6.539
6.601
6.674
6.768
6.851
1.500 x .750
8.03
7.20
7.80
8.50
7.40
10.20
2.38
5.65
4.82
5.42
6.12
7.02
7.82
.038
624
...
t Coupling selections are based on coupling bore capacity and standard available hub lengths. Check coupling rating for all selections, and hub key stress for mill motor
(421-110) 41
Engineering Data
ZC
ZE
ZH
Table 23 specifies the taper and counter bore limitations for the
usual requirements. Refer applications for counter bore diameters
or depths which exceed any of these limitations, and
requirements for hubs longer than those listed, to Falk with full
particulars for review.
ZD
GAP
SIDE
R
UH
BASIC
DIA.
KEYWAY
PARALLEL
TO BORE
UG
Z
Max
UG
Min
UH
Max
ZD
Max
Keyway s
20/1020T
30/1030T
40/1040T
50/1050T
60/1060T
70/1070T
80/1080T
90/1090T
100/1100T
110/1110T
120/1120T
130/1130T
140/1140T
150/1150T
160/1160T
1170T
3.88
4.12
4.12
6.50
6.59
6.59
8.09
8.09
8.06
8.06
8.03
8.03
8.03
7.20
7.80
8.50
.12
.12
.12
.25
.25
.25
.38
.38
.50
.50
.62
.62
.75
.75
.75
.75
1.438
1.812
2.125
2.562
2.875
3.312
4.062
4.625
5.375
6.000
6.500
8.000
9.250
10.500
12.000
14.000
.500
.500
.500
.500
.750
.750
1.062
1.062
1.625
1.625
2.375
2.625
2.625
4.250
4.750
5.250
1.125
1.375
1.625
1.875
2.125
2.500
3.000
3.500
4.000
4.500
5.000
6.000
7.000
8.000
9.000
10.000
.62
.62
.62
.81
.81
.88
1.25
1.38
1.69
1.75
2.00
2.06
2.25
2.50
2.75
3.00
.250 x .125
.312 x .156
.375 x .188
.500 x .250
.500 x .250
.625 x .312
.750 x .375
.875 x .438
1.000 x .500
1.000 x .500
1.250 x .625
1.500 x .750
1.750 x .625
2.000 x .750
2.000 x .750
2.500 x .875
Q Standard long hub length available for Type T Hubs and flanged hubs; consult Falk for longer lengths.
s
SIZE
B.C.
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
1210T
1220T
1230T
1240T
1250T
1260T
1.531
1.875
2.125
2.500
2.875
3.312
3.937
4.562
5.250
5.875
6.625
7.750
9.125
10.375
11.750
13.250
14.875
16.250
17.937
19.562
21.312
23.062
24.938
27.188
29.500
Shaft Hub
B.C.
2.812
3.125
3.875
4.250
4.938
5.250
4.062
4.625
5.750
6.562
7.500
8.188
9.250
.375-16 x
.375-16 x
.375-16 x
.375-16 x
.375-16 x
.375-16 x
.375-16 x .50
.375-16 x .50
.625-11 x .82
.625-11 x .82
.750-10 x .94
.750-10 x .94
.750-10 x .94
T41 Hub
1020T
1030T
1040T
1050T
1060T
1070T
1080T
1090T
1100T
1110T
1120T
1130T
1140T
1150T
1160T
1170T
1180T
1190T
1200T
1.000
1.250
1.375
1.750
1.875
2.250
2.750
3.250
3.500
4.000
4.500
5.500
6.500
7.000
8.000
9.000
9.750
10.750
11.750
[
[
1.250
1.500
1.750
2.125
2.375
2.875
3.250
3.750
4.250
5.000
5.875
6.500
7.500
8.875
9.750
10.750
11.750
Shaft Hub
for T31 & T35
1.250
1.500
2.000
2.125
2.750
2.875
3.250
3.750
4.500
5.000
6.000
6.500
7.500
8.750
9.750
11.000
11.750
13.000
13.500
42 (421-110)
Engineering Data
TABLE 27 Standard Bore Fits Unless
Otherwise Specified, Falk
Coupling Hubs Will Be Bored
With The Following Bore Fits:
Model
Steelflex
Grid
Couplings
Coupling Size
Coupling Type
Bore Fit
1020 - 1090
Clearance
All Types
Interference
All Sizes
Interference
Clearance Fit
Interference Fit
Shaft
Dia
+.0000
.0010
2.2500
2.3125
2.3750
2.4375
2.5000
2.5625
2.6250
2.6875
2.7500
2.8125
2.8750
2.9375
3.0000
+.0000
.0010
3.0625
3.1250
3.1875
3.2500
3.3125
3.3750
3.4375
3.5000
3.5625
3.6250
3.6875
3.7500
3.8125
3.8750
3.9375
4.0000
Clearance Fit
Interference Fit
t For shaft diameters larger than 20.000, use an average interference fit of .0005" per inch of shaft
Shaft
Dia
+.0000
.0010
4.0625
4.1250
4.1875
4.2500
4.3125
4.3750
4.4375
4.5000
4.5625
4.6250
4.6875
4.7500
4.8125
4.8750
4.9375
5.0000
5.0625
5.1250
5.1875
5.2500
5.3125
5.3750
5.4375
5.5000
5.5625
5.6250
5.6875
5.7500
5.8125
5.8750
5.9375
6.0000
6.2500
6.5000
Clearance Fit
Interference Fit
Shaft
Dia
+.0000
.0010
6.7500
7.0000
+.0000
.0010
7.250
7.500
7.750
8.000
8.250
8.500
8.750
9.000
9.250
9.500
9.750
10.000
10.250
10.500
10.750
11.000
11.250
11.500
11.750
12.000
12.500
13.000
13.500
14.000
14.500
15.000
+.000
.001
15.500
16.000
16.500
17.000
17.500
18.000
18.500
19.000
19.500
20.000
Interference Fit
Hub
InterBore ference
+.0015 .0015
.0000 .0040
6.7460
6.9960
+.0020 .0020
.0000 .0050
7.2450
7.4950
7.7450
7.9950
8.2445 .0025
8.4945 .0055
8.7445
8.9945
9.2440 .0030
9.4940 .0060
9.7440
9.9940
10.2435 .0035
10.4935 .0065
10.7435
10.9935
11.2430 .0040
11.4930 .0070
11.7430
11.9930
12.4925 .0045
12.9925 .0075
13.4920 .0050
13.9920
.0080
14.4915 .0055
14.9915 .0085
+.0025 .0055
.0000 .0090
15.4910
15.9910
16.4905 .0060
16.9905
.0095
17.4895 .0070
17.9895
.0105
18.4890 .0075
18.9890
.0110
19.4880 .0085
19.9880
.0120
(421-110) 43
Engineering Data
Shaft Diameter
(ISO/R775-1969)
Nominal
Tolerance
Clearance
Transitional
Interference
j6 / k6 t
F7
H7
M6
Over 30 to 50
k6
F7
H7
K6
Over 50 to 80
m6
F7
H7
K7
Over 80 to 100
m6
F7
H7
M7
m6
F7
H7
P7
m6
F7
H7
R7
m6
F7
H7
R8
6 to 30
j6
+.008 / .003
0.4727 / 0.4724
0.5515 / 0.5511
0.6302 / 0.6298
0.7089 / 0.7066
j6
0.009 / .004
0.7483 / 0.7479
0.7877 / 0.7873
0.8665 / 0.8660
0.9452 / 0.9448
0.9846 / 0.9841
1.1027 / 1.1022
1.1814 / 1.1810
k6
+.018 / +.002
1.2605 / 1.2600
1.3786 / 1.3781
1.4967 / 1.4962
1.5755 / 1.5749
1.6542 / 1.6537
1.7723 / 1.7718
1.8904 / 1.8899
1.9692 / 1.9686
m6
+.030 / +.011
2.1665 / 2.1658
2.2059 / 2.2052
2.3634 / 2.3627
2.4815 / 2.4808
2.5602 / 2.5595
2.7571 / 2.7564
2.7964 / 2.7957
2.9539 / 2.9532
3.1508 / 3.1501
m6
+035 / +.013
3.3478 / 3.3470
3.5447 / 3.5438
3.7415 / 3.7407
3.9384 / 3.9375
m6
+.035 / +.013
4.3321 / 4.3312
4.7258 / 4.7249
m6
0.040 / +.015
4.9228 / 4.9219
5.1197 / 5.1187
5.5134 / 5.5124
5.9071 / 5.9061
6.3008 / 6.2998
6.6945 / 6.6935
7.0882 / 7.0872
Clearance Fit
Hub Bore
F7
+.016 / +.034
0.4731 / 0.4737
0.5518 / 0.5525
0.6306 / 0.6312
0.7093 / 0.7100
F7
+.020 / +.041
0.7488 / 0.7496
0.7882 / 0.7890
0.8670 / 0.8677
0.9457 / 0.9465
0.9851 / 0.9858
1.1032 / 1.1039
1.1819 /1.1827
F7
+.025 / +.050
1.2609 / 1.2618
1.3790 / 1.3799
1.4971 / 1.4980
1.5758 / 1.5767
1.6546 / 1.6555
1.7727 / 1.7736
1.8908 / 1.8917
1.9695 / 1.9704
F7
+.030 / +.060
2.1666 / 2.1677
2.2059 / 2.2071
2.3634 / 2.3645
2.4815 / 2.4827
2.5603 / 2.5614
2.7571 / 2.7582
2.7965 / 2.7976
2.9540 / 2.9551
3.1508 / 3.1519
F7
+.036 / +.071
3.3479 / 3.3492
3.5447 / 3.5461
3.7416 / 3.7429
3.9384 / 3.9398
F7
+.036 / +0.071
4.3321 / 4.3335
4.7258 / 4.7272
F7
+.043 / +.083
4.9230 / 4.9245
5.1198 / 5.1214
5.5135 / 5.5151
5.9072 / 5.9088
6.3009 / 6.3025
6.6946 / 6.6962
7.0883 / 7.0899
Transitional Fit
Fit Q
+.008
+.037
+.0003
+.0015
+.011
+.045
+.0004
+.0018
+.007
+.048
+.0003
+.0019
+.000
+.049
+.0000
+.0019
+.001
+.058
+.0000
+.0023
+.003
+.068
+.0001
+.0027
Hub Bore
H7
+.000 / +.018
0.4725 / 0.4731
0.5512 / 0.5519
0.6300 / 0.6306
0.7087 / 0.7093
H7
+.000 / +.021
0.7481 / 0.7488
0.7874 / 0.7882
0.8662 / 0.8669
0.9449 / 0.9457
0.9843 / 0.9850
1.1024 / 1.1032
1.1811 / 1.1819
H7
+.000 / +.025
1.2599 / 1.2608
1.3780 / 1.3789
1.4961 / 1.4970
1.5748 / 1.5758
1.6536 / 1.6545
1.7717 / 1.7726
1.8898 / 1.8907
1.9685 / 1.9695
H7
+.000 / +.030
2.1654 / 2.1665
2.2047 / 2.2059
2.3622 / 2.3634
2.4803 / 2.4815
2.5591 / 2.5602
2.7559 / 2.7571
2.7953 / 2.7964
2.9528 / 2.9539
3.1469 / 3.1508
H7
+.000 / +.035
3.3465 / 3.3478
3.5433 / 3.5447
3.7402 / 3.7415
3.9370 / 3.9384
H7
+.000 / +.035
4.3307 / 4.3321
4.7244 / 4.7258
H7
+.000 / +.040
4.9213 / 4.9228
5.1181 / 5.1197
5.5118 / 5.5134
5.9055 / 5.9071
6.2992 / 6.3008
6.6929 / 6.6945
7.0866 / 7.0882
Interference Fit
Fit Q
.008
+.021
.0003
+.0008
.009
+.025
.0004
+ .0010
.018
+.023
.0007
+.0009
.030
+.019
.0012
+.0007
.035
+.022
.0014
+.0009
.040
+.025
.0016
+.0010
H Dimensions shaded are in millimeters. Nonshaded are in inches. Inch hub bore rounding practice per ISO 370-1975 (E) Method A.
Q Positive values are clearance, negative values are interference. For reference only.
44 (421-110)
Hub Bore
M6
.015 / .064
0.4718 / 0.4723
0.5506 / 0.5511
0.6293 / 0.6298
0.7080 / 0.7085
M6
.017 / .004
0.7473 / 0.7479
0.7867 / 0.7873
0.8654 / 0.8660
0.9442 / 0.9448
0.9835 / 0.9841
1.1017 / 1.1022
1.1804 / 1.1810
K6
.013 / +.003
1.2593 / 1.2600
1.3774 / 1.3781
1.4955 / 1.4962
1.5743 / 1.5760
1.6530 / 1.6537
1.7711 / 1.7718
1.8892 / 1.8899
1.9680 / 1.9687
K7
.021 / +.009
2.1645 / 2.1657
2.2039 / 2.2051
2.3614 / 2.3626
2.4795 / 2.4807
2.5582 / 2.5594
2.7551 / 2.7563
2.7944 / 2.7957
2.9519 / 2.9531
3.1488 / 3.1500
M7
.035 / +.000
3.3451 / 3.3465
3.5419 / 3.5433
3.7388 / 3.7402
3.9356 / 3.9370
P7
.059 / .024
4.3284 / 4.3298
4.7221 / 4.7235
P7
.068 / .028
4.9186 / 4.9202
5.1154 / 5.1170
5.5091 / 5.5107
5.9028 / 5.9044
6.2965 / 6.2981
6.6902 / 6.6918
7.0839 / 7.0855
Fit Q
.023
.001
.0009
+.0000
.026
+.000
.0010
+.0000
.031
+.001
.0012
+.0000
.051
.002
.0020
.0001
.070
.013
.0028
.0005
.094
.037
.0037
.0015
.108
.043
.0043
.0017
Continued on Page 45
Rexnord Industries, Inc. 1963, 2004.
Engineering Data
TABLE 30 Recommended Bores for Metric Shafts per ISO/R7751969 H (Continued)
Shaft Diameter
>180
MM
190
200
>200
MM
210
220
225
>225
MM
230
240
250
>250
MM
260
270
280
>280
MM
290
300
310
315
>315
MM
320
330
340
350
355
>355
MM
360
370
380
390
400
>400
MM
410
420
430
440
450
>450
MM
460
470
480
490
500
m6
+.046 / +.017
7.4821 / 7.4810
7.8758 / 7.8747
m6
+.046 / +.017
8.2695 / 8.2684
8.6632 / 8.6621
8.8601 / 8.8589
m6
+.046 / +.017
9.0569 / 9.0558
9.4506 / 9.4495
9.8443 / 9.8432
m6
+.052 / +.020
10.2383 / 10.2370
10.6320 / 10.6307
11.0257 / 11.0244
m6
+.052 / +.020
11.4194 / 11.4181
11.8131 / 11.8118
12.2068 / 12.2055
12.4036 / 12.4024
m6
.+057 / +.021
12.6007 / 12.5993
12.9944 / 12.9930
13.3881 / 13.3867
13.7818 / 13.7804
13.9786 / 13.9772
m6
+.057 / +.021
14.1755 / 14.1741
14.5692 / 14.5678
14.9629 / 14.9615
15.3566 / 15.3552
15.7503 / 15.7489
m6
+.063 / +.023
16.1442 / 16.1426
16.5379 / 16.5363
16.9316 / 16.9300
17.3253 / 17.3237
17.7190 / 17.7174
m6
+.063 / +.023
18.1127 / 18.1111
18.5064 / 18.5048
18.9001 / 18.8985
19.2938 / 19.2922
19.6875 / 19.6859
Clearance Fit
Hub Bore
F7
+.050 / +.096
7.4823 / 7.4841
7.8760 / 7.8778
F7
+.050 / +.096
8.2697 / 8.2715
8.6634 / 8.6652
8.8602 / 8.8620
F7
+.050 / +.096
9.0571 / 9.0589
9.4508 / 9.4526
9.8445 / 9.8463
F7
+.056 / +.108
10.2384 / 10.2405
10.6321 / 10.6342
11.0258 / 11.0279
F7
+.056 / +.108
11.4195 / 11.4216
11.8132 / 11.8153
12.2069 / 12.2090
12.4038 / 12.4058
F7
+.062 / +.119
12.6009 / 12.6031
12.9946 / 12.9968
13.3883 / 13.3905
13.7820 / 13.7842
13.9788 / 13.9811
F7
+.062 / +.119
14.1757 / 14.1779
14.5694 / 14.5716
14.9631 / 14.9653
15.3568 / 15.3590
15.7505 / 15.7527
F7
+.068 / +.131
16.1444 / 16.1469
16.5381 / 16.5406
16.9378 / 16.9343
17.3255 / 17.3280
17.7192 / 17.7217
F7
+.068 / +.131
18.1129 / 18.1154
18.5066 / 18.5091
18.9003 / 18.9028
19.2940 / 19.2965
19.6877 / 19.6902
Transitional Fit
Fit Q
+.004
+.079
+.0002
+.0031
+.004
+.088
+.0002
+.0035
+.005
+.098
+.0039
+.005
+.108
+.0002
+.0043
Hub Bore
H7
+.000 / +.046
7.4803 / 7.4821
7.8740 / 7.8758
H7
+.000 / +.046
8.2677 / 8.2695
8.6614 / 8.6632
8.8583 / 8.8601
H7
+.000 / +.046
9.0551 / 9.0569
9.4488 / 9.4506
9.8425 / 9.8443
H7
+.000 . +.052
10.2362 / 10.2383
10.6299 / 10.6320
11.0236 / 11.0257
H7
+.000 / +.052
11.4173 / 11.4194
11.8110 / 11.8131
12.2047 / 12.2068
12.4016 / 12.4036
H7
+.000 / +.057
12.5984 / 12.6007
12.9921 / 12.9944
13.3858 / 13.3881
13.7795 / 13.7818
13.9764 / 13.9786
H7
+.000 / +.057
14.1732 / 14.1755
14.5669 / 14.5692
14.9606 / 14.9629
15.3543 / 15.3566
15.7480 / 15.7503
H7
+.000 / +.063
16.1417 / 16.1442
16.5354 / 16.5379
16.9291 / 16.9316
17.3228 / 17.3253
17.7165 / 17.7190
H7
+.000 / +.063
18.1102 / 18.1127
18.5039 / 18.5064
18.8976 / 18.9001
19.2913 / 19.2938
19.6850 / 19.6875
Interference Fit
Fit Q
.046
+.029
.0018
+.0011
.052
+.032
.0020
+.0013
.057
+.036
.0022
+.0014
.063
+.040
.0025
+.0016
H Dimensions shaded are in millimeters. Nonshaded are in inches. Inch hub bore rounding practice per ISO 370-1975 (E) Method A.
Q Positive values are clearance, negative values are interference. For reference only.
Hub Bore
P7
.079 / .033
7.4772 / 7.4790
7.8709 / 7.8727
R7
.109 / .063
8.2634 / 8.2652
8.6571 / 8.6589
8.8540 / 8.8558
R7
.113 / .067
9.0507 / 9.0525
9.4444 / 9.4462
9.8381 / 9.8399
R7
.126 / .074
10.2313 / 10.2333
10.6250 / 10.6270
11.0187 / 11.0207
R7
.130 / .078
11.4122 / 11.4123
11.8059 / 11.8080
12.1996 / 12.2017
12.3965 / 12.3985
R7
.144 / .187
12.5928 / 12.5950
12.9865 / 12.9887
13.3802 / 13.3824
13.7739 / 13.7761
13.9707 / 13.9730
R8
.203 / .114
14.1652 / 14.1687
14.5589 / 14.5624
14.9526 / 14.9561
15.3463 / 15.3498
15.7400 / 15.7435
R8
.223 / .126
16.1330 / 16.1368
16.5267 / 16.5305
16.9204 / 16.9242
17.3141 / 17.3179
17.7078 / 17.7116
R8
.229 / .132
18.1012 / 18.1050
18.4949 / 18.4987
18.8886 / 18.8924
19.2823 / 19.2861
19.6760 / 19.6798
Fit Q
.125
.050
.0049
.0020
.155
.080
.0061
.0031
.159
.084
.0063
.0033
.178
.094
.0070
.0037
.182
.098
.0072
.0039
.201
.108
.0079
.0043
.260
.135
.0102
.0053
.286
.149
.0113
.0059
.292
.155
.0115
.0061
(421-110) 45
Phone
Fax
Address
E-Mail
Response Reqd By
Date
Submitted By
COUPLING TYPE:
COUPLING DESIGN:
Disc o
Grid o
Gear o
Horizontally Mounted o
Close Coupled o
Elastomer o
Spacer o
Other
Vertically Mounted o
Engine o (No. of Cyl.)
Diesel o
Gasoline o
Turbine o
Gas o
Steam o
Air o
Gas o
Unidirectional o
Smooth o
Intermittent o
Reversing o
Light Shock o
Little Vibration o
Heavy Shock o
Med. Vibration o
Hvy. Vibration o
Interference o
Other _______________
Interference o
Other _______________
Specifications Applicable:
API-610 o
API-671 o
Others ______________________
Service Factor:
AGMA Recommended o
Other ______________________
SKETCH AREA
Competitive Data:
Make _________________________________________________
Size & Type ____________________________________________
Bores _____________________ & _________________________
Price _____________________
Additional Comments: __________________________________
_______________________________________________________
_______________________________________________________
_______________________________________________________
46 (421-110)