Professional Documents
Culture Documents
Vane Pump & Motor Design Guide - Eaton
Vane Pump & Motor Design Guide - Eaton
Revised 08/98
353
Introduction
Over the past twenty years, the
application of hydraulics in agricultural,
construction and materials handling
vehicles has seen a meteoric rise. In
fact, virtually all modern vehicles use
fluid power, and new vehicles and
markets are appearing as fast as the
development of new products and
concepts will allow.
Vehicle size and work capacity are
growing. Todays front-end loaders, for
example, have bucket capacities equal
to the capacities of scrapers of just a few
years ago. To provide equipment with
still larger load capacities, and increased
speed to do the job faster, the trend is
toward high-speed, high-pressure
hydraulic pumps and motors that allow
system components to remain relatively
small.
To meet the ever increasing demands
for fast positive action, longer service life
and economical vehicle operation,
Vickers offers you the large selection of
top-quality, precision-built pumps and
motors described in the following pages.
They are backed by over seven
decades of experience with every type
of hydraulic equipment.
You can always depend on Vickers for
the finest, most advanced hydraulic
products and the best in customer
service. Vickers has the worldwide
facilities and skilled personnel to give
you prompt deliveries, volume
production, and application and service
assistance when you need it.
Table of Contents
Applying Vane Units
Pump & Motor Characteristics and Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Dimensions, Circuitry Requirements, Fluid and Fluid Cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reservoirs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pump Startup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
7
8
66
67
68
69
72
73
3
66
78
79
80
83
84
89
90
91
94
103
104
105
107
108
Accessory Products
Foot Mounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Filler/Breather Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
SAE 4-Bolt Solid Flanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Oil Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Hydraulic Formulae . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Flow Capacities of Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Motor Characteristics
Maximum Speed
Minimum Speed
Minimum Speed
Stall Torque
Inlet Pressure
Recommended inlet pressure is
0 to 0,34 bar (0 to 5 psi) gauge.
Inlet pressure should not exceed
1,38 bar (20 psi). Inlet depressions
should not exceed 0,17 bar (5 of Hg
or 12.2 psia).
Rated Pressure
Pumps should not be operated at or
near rated pressures at idle speeds for
extended periods. Localized overheating
and damage can result.
Never assume pumps in a double, triple
or thru-drive pump assembly can be
simultaneously loaded to rated pressure.
Shaft loading must be checked for
excessive torque and side loads.
Hydraulic Braking
Drive Alignment
Concentricity and angular alignment of
shafts are important to pump life.
Misalignment can induce heavy loads
on bearings, causing premature failure.
Flexible coupling halves must be aligned
according to the coupling manufacturers
recommendations.
Universal Joints
When using double universal joint
couplings, the shafts must be parallel
and the yokes must be in line. The offset
should be kept as low as possible.
Maximum allowable offset will, of course,
vary with application conditions. The
pump shaft to universal joint diametral fit
should be close (major diameter fit) with
no looseness.
Drives
Recommended Drives
Vickers units are designed for use on
direct coaxial drives using spline
connections and/or flexible couplings. If
drives imposing radial or axial loads, or
key drives, are being considered,
consult your Vickers representative for
additional information.
Mounting Dimensions
Requirements
Dimensional control requirements of the
customers mounting pad to which the
pump or motor is affixed are as follows.
Pilot Diameter
Concentricity of the customers female
pilot diameter relative to the effective
axis of the female drive must be within
0,10 mm (.004 in.) total indicator
reading. The clearance between the male
and female pilot diameters must be +0,01
to +0,05 mm (+.0005 to +.0020 in.).
Mounting Face
The customers mounting face to which
the pump or motor is affixed must be
square to the axis of the female drive
within 0,0381 mm per mm (.0015 inch
per inch).
Shafts
Dimensions of keyed shaft receivers
must be between +0,003 and +0,03 mm
(+.0001 and +.0010 in.) of the maximum
shaft diameter shown on the Vickers
installation drawing.
Circuitry Requirements
Valves
In the event of acceleration or
deceleration of the drive or driven
members, overrunning loads or system
bleed-off, control valves and circuitry
must provide a continuous supply of oil
to the pump or motor. This supply
should be sufficient to prevent transient
or continuous cavitation, but not so large
as to result in speeds beyond the
published maximum speed.
Protect against hydraulic surge
pressures (inlet, outlet or drain) applied
to or generated by the pump or motor.
Relief valves must prevent these surges
from exceeding published pressure
ratings.
Never assume a relief valve setting is
the maximum pressure a pump
experiences. Shock conditions may
exist which can exceed circuit and pump
limitations.
Piping
Hydraulic lines should be as short and
have as large an inside diameter as
possible. Where lines are long, it is
desirable to adapt to a larger capacity
line than a units ports specify. Inlet,
outlet and drain lines should not be
Hose
Because steering components move
during operation, their working hydraulic
lines consist mainly of flexible hoses.
Long lines may be partly flexible hose
and partly tubing where flexibility is not
required.
When installing a hose, allow enough
slack to avoid kinking. A taut hose will
not allow movement with pressure
surges. Slack in the line compensates
for surges, relieving strain. The hose
should not be twisted during installation
or while in operation. Twisting will
weaken the hose and loosen
connections.
For power steering pumps using a
remote reservoir, connecting hoses
should not exceed three feet in length. It
is highly desirable to design the
reservoir-pump relationship so that there
is always a static head on the pump inlet
port.
A neater installation is usually
obtainable by using extra fittings to
minimize unusually long loops in a line.
Hoses should be clamped to prevent
rubbing and entanglement with moving
parts. Where hoses are subject to
chafing, they should be run through
protective neoprene hose or shielded
metallic guards.
Fluid Considerations
Preferred Viscosity
Normal pump operation (at rated
conditions) is based on the use of SAE
10W oil in the 38 to 82 C (100 to
180 F) range (or comparable
viscosities).
Permissible Viscosity
When operating with SAE 10W oil in the
860 to 40 cSt (4000 to 180 SUS) range
(-12 to 35 C or 10 to 95 F oil temp.),
the speed and pressure of the pump
should be limited to 50% or less of their
respective rated value until the system
has warmed up. Caution must be used
in starting units when fluid viscosity is
greater than 860 cSt (4000 SUS). Care
should be exercised to warm up the
entire system (fluid). Remote
components (cylinders, motors) should
be actuated during the warm-up
process.
Fluid viscosities must not be less than
60 SUS, and temperatures should not
exceed 99 C (210 F), because the life
expectancy of rotating groups and
elastomers will decrease.
Care should be taken to change to
appropriate oil viscosities when climatic
conditions change. See
recommendations for mobile hydraulic
systems on pages 120 and 121. Consult
your Vickers representative for
applicable decreases in ratings, and
modifications, if fluids other than SAE
type oils are considered.
Fluid Cleanliness
Proper fluid condition is essential for
long and satisfactory life of hydraulic
components and systems. Hydraulic
fluid must have the correct balance of
cleanliness, materials, and additives for
protection against wear of components,
elevated viscosity and inclusion of air.
Essential information on the correct
methods for treating hydraulic fluid is
included in Vickers publication 561;
Vickers Guide to Systemic
Contamination Control, available from
your local Vickers distributor or by
contacting Vickers, Incorporated.
Recommendations on filtration and the
selection of products to control fluid
condition are included in this publication.
Recommended cleanliness levels using
petroleum oil under common conditions
are based on the highest fluid pressure
levels in the system. See Figure 1.
Fluids other than petroleum, severe
service cycles or temperature extremes
are cause for adjustment of these
cleanliness codes. See Vickers
publication 561 for exact details.
Product
1000 psi
20/18/15
18/16/14
19/17/15
18/16/14
20/18/15
17/15/12
19/17/14
20/18/15
20/18/15
19/17/14
20/18/14
18/16/13
17/15/13
16/14/12
19/17/14
15/13/11
19/17/14
20/18/15
18/16/13
17/15/12
18/16/13
Filler/Breather
Most reservoirs are vented to the
atmosphere through an opening that lets
air leave or enter the space above the
oil as the oil level rises or falls. A
filler/breather unit containing an air
filtering element, such as shown on
page 118, is often used as the vent.
It must be large enough to handle
the air flow required to maintain
atmospheric pressure whether the
tank is full or empty.
Figure 1
Aeration
Location
Reservoirs
Oil Level
The oil level of the reservoir should be
as high as possible above the pump
suction line opening. All return lines
should discharge near the tank bottom,
always below the oil level, and as far
from the pump inlet as possible.
For power steering pumps using a
remote reservoir, the oil level should not
be lower than one foot below the pump
shaft centerline.
Reservoirs should incorporate a sight
gauge, dipstick or other means for easy
checking of the oil level. Without these
devices, the oil level often goes
unchecked and, should a leak occur, the
pump can be starved and damaged
from loss of lubrication.
Line Connections
Pump suction and tank return lines
should be attached to the reservoir by
flanges or welded heavy-duty coupling.
If the suction line is connected to the
bottom of the reservoir, the coupling
should extend above the bottom inside
the tank. This prevents residual dirt from
getting into the suction line when the
tank is cleaned. The seals used on all
suction line connections should be such
that they will not deteriorate and leak.
Baffle Plate
A baffle plate in the reservoir is desirable
to separate the suction and return lines.
The plate causes return oil to circulate
around the outer wall of the reservoir for
cooling before it re-enters the pump. It
also helps provide time for entrained air
to separate from the oil. Baffle plate
openings should be designed so that
cascade effects and resultant air
entrainment are minimized.
Magnets
Magnets in a reservoir should be able to
pick up ferrous particles not retained by
filters or strainers. Magnets should be
assembled to the support bars located
between suction and return lines, and be
accessible for cleaning.
Pump Start-up
Circuit Cleanup
Single 35VQ
Triple 4525VQSV10F
Double 3525VQ
Design Features
Performance
Durability
Vickers high speed-high pressure
pumps give more staying power they
last. Their workhorse ruggedness has
been proved on the newest types of
giant earth-moving equipment.
Replaceable Cartridge
OUTLET
ROTOR
VANE
Hydraulic Balance
Pump inlet and outlet pressure
chambers are diametrically opposed as
shown in Figure 2. As a result, the rotor
is hydraulically balanced. Bearings thus
encounter no hydraulic loads, assuring
long life.
Figure 3 shows an insert fitted into a slot
in the vane. Outlet pressure is applied
continuously only to the space between
the vane and insert. Top and bottom
areas of the vane are subject to either
inlet or outlet pressure, depending upon
the vanes location during rotor rotation.
See Figure 2. Complete hydraulic
balance is effected in the outlet pressure
areas. Outward thrust by the vane in the
inlet area is equal to the outlet pressure
times the projected area of the end of
the insert.
INLET
PASSAGE TO
UNDERSIDE
OF VANE
Figure 2
INLET OR
OUTLET
PRESSURE
CONTINUOUS
OUTLET
PRESSURE
Double Pumps
Double pumps provide a single power
source capable of serving two separate
hydraulic circuits, or of providing greater
volume through the combined delivery of
both sections. In either type of
application, two pumps in a single
housing result in a more compact,
simple installation and can be driven
through a single shaft coupling.
Triple Pumps
Because triple pumps have three pumps
in a single housing, they offer even more
application versatility than do the double
pumps described above.
Thru-Drive Pumps
These versions of single and double
pumps have a rear pad for directly
mounting and driving an additional
pump. Many different multi-pump
arrangements are thus possible.
Figure 3
10
Delivery USgpm
@ 1200 r/min
7 bar (100 psi)
Displ.
cm3/r
(in3/r)
Max.
r/min
Max.
bar (psi)
Typical del.
L/min
(USgpm)
@ max. speed
& pressure
Typical
input
kW (hp)
@ max. speed
& pressure
20VQ
5
8
11
12
14
12
14
17
21
18,0 (1.10)
27,4 (1.67)
36,4 (2.22)
39,5 (2.41)
45,9 (2.80)
40,2 (2.45)
45,4 (2.77)
55,2 (3.37)
67,5 (4.12)
2700
2700
2700
2700
2700
2700
2700
2500
2500
210 (3000)
210 (3000)
210 (3000)
160 (2300)
140 (2000)
210 (3000)
210 (3000)
210 (3000)
210 (3000)
42,3 (11)
65,4 (17)
88,5 (23)
98,1 (25.5)
115,4 (30)
88,5 (23)
103,8 (27)
119,2 (31)
146,2 (38)
17,9 (24)
26,1 (35)
35,4 (47.5)
28,4 (38)
29,1 (39)
41,0 (55)
46,6 (62.5)
51,8 (69.5)
61,9 (83)
25
30
35
38
81,6 (4.98)
97,7 (5.96)
112,8 (6.88)
121,6 (7.42)
2500
2500
2400
2400
210 (3000)
210 (3000)
210 (3000)
210 (3000)
173,1 (45)
211,5 (55)
230,8 (60)
250,0 (65)
75,3 (101)
87,7 (117.5)
98,5 (132)
104,4 (140)
42
50
60
138,7 (8.46)
162,3 (9.90)
193,4 (11.80)
2200
2200
2200
175 (2500)
175 (2500)
175 (2500)
255,8 (66.5)
303,8 (79)
369,2 (96)
91,4 (122.5)
105,2 (141)
126,8 (170)
25VQ
35VQ
45VQ
Weight
kg (lb)
11,8 (26)
14,5 (32)
22,7 (50)
34,1 (75)
Performance constants: SAE 10W fluid @ 82C (180F), and pump inlet @ 0 PSIG (14.7 PSIA)
Note: Outlet pressure must always be higher than inlet pressure.
See page 5 for details.
11
Model Codes
Single Pump
(F3) - 20VQ F - 5 - A - S -1 - C - 2 - K - 30 - L
1
1 F3 Viton seals
Omit if not required.
18,0
27,4
36,4
39,5
45,9
5
8
11
12
14
in3/r
1.10
1.67
2.22
2.41
2.80
Port connections
Series
20VQ
Code
A
Inlet
SAE
4-bolt flg.
20VQ
AM* Metric
4-bolt flg.
20VQF&P B
SAE
Str. thd.
20VQF&P C
SAE
4-bolt flg.
Shaft type
1 Straight keyed
151 Splined
10
11
10
12
F 100 (1500)
G 121 (1750)
H 140 (2000)
J 155 (2250)
K 175 (2500)
Geometric displacement
Code
Outlets
SAE
4-bolt flg.
Metric
4-bolt flg.
SAE
Str. thd.
SAE
Str. thd.
Outlet positions
11
Design
Subject to change. Installation
dimensions remain the same for
designs 30 through 39.
12
Shaft rotation
(Viewed from shaft end of pump)
L Left hand or counterclockwise.
Omit for right hand.
9
Controlled flow rate
(20VQF & 20VQP)
3 11 L/min (3 USgpm)
4 15 L/min (4 USgpm)
6 23 L/min (6 USgpm)
7 27 L/min (7 USgpm)
8 30 L/min (8 USgpm)
10 38 L/min (10 USgpm)
11 42 L/min (11 USgpm)
12 45 L/min (12 USgpm)
12
Model Codes
Single Pump
25VQ (S) 21
1
F3 - Viton seals
Standard
Heavy duty
bearing bearing
25VQ
26VQ
35VQ
36VQ
45VQ
0 (L)
9
Port connections
Series Code
All
A
(S) 11 C
All
AM*
25VQ
25VQ
25VQ
Inlet
SAE
4-bolt flg.
Metric
4-bolt flg.
SAE
str. thd.
SAE
4-bolt flg.
SAE
str. thd.
Outlet
SAE
4-bolt flg.
Metric
4-bolt flg.
SAE
str. thd.
SAE
str. thd.
SAE
4-bolt flg.
Pilot designation
Geometric displacement
35V
45V
Code
cm3/r
in3/r
12
14
17
21
25
30
35
38
42
50
60
40,2
45,4
55,2
67,5
81,6
97,7
112,8
121,6
138,7
162,3
193,4
2.45
2.77
3.37
4.12
4.98
5.96
6.88
7.42
8.46
9.90
11.80
10
Outlet positions
Design
10
Rotation
Shaft type
13
Installation Dimensions
20VQ Series
101,60 (4.000)
101,55 (3.998)
101,6
(4.00)
OUTLET CONNECTION
19,0 (.75)
.500-13 UNC-2B,
OR M12,
21,0 (.83) DEEP
155,4
(6.12)
OPTIONAL
1.625-12UN-2B
STRAIGHT THD
CONNECTION
FOR SAE
HYD FITTINGS
INLET CONNECTION
38,1 (1.50)
132,6
(5.22)
63,5
(2.5)
9,5
(.375)
146
(5.75)
76,2
(3.00)
55,4
(2.18)
12,7
(.50)
174,6
(6.875)
.750-16UNF 2B THD.
FOR SAE HYD. FITTINGS
20VQF Series
Additional dimensions are
shown above.
3,2
(.125)
23,1
(.91)
20,6
(.81)
170,9
(6.73)
TANK PORT
113,5
(4.47)
12,7
(.50)
99,1
(3.90)
SEE SHAFT
OPTIONS
STARTING
ON PAGE 17.
50,0
(1.97)
50,8
(2.00)
78,5
(3.09)
153,7
(6.05)
14
Installation Dimensions
20VQP Series
Dimensions in millimeters (inches)
16,0 (.63)
16,0 (.63)
55,4 (2.18)
181,6
(7.15)
62,0
(2.44)
62,0
(2.44)
46,0
(1.81)
SECONDARY OUTLET PORT
.875-14 UNF-2B THD.
FOR SAE HYD. FITTINGS
25VQ Series
Dimensions in millimeters (inches)
.500-13 UNC OR M12
22,3 (.88) DEEP
58,7
(2.31)
PORT CONNECTION PADS ARE FOR
USE WITH 4-BOLT FLANGES.
SEE PAGE 119 FOR SELECTION.
58,7
(2.31)
.375-16 UNC OR M10
19,0 (.75) DEEP
INLET CONNECTION
38,1 (1.50)
76,2 (3.00) FOR SAE 4-BOLT
FLANGE PADS. 85,9 (3.38) FOR
1.875-12 STRAIGHT THREADED
INLET AND 1.312-12 OUTLET.
SEE MODEL CODE, PAGE 13.
164,1
(6.46)
OUTLET CONNECTION
25,4 (1.00)
120,7
(4.75) 38,1
(1.50)
101,6
101,5
(4.000)
(3.998)
B
63,5
(2.50)
12,7
(.50)
9,53
(.375)
146,1
(5.75)
60,5
R.
(2.38)
14,2 (.56)
THRU 2 HOLES
15
35VQ Series
Dimensions in millimeters
(inches)
15,7
(.62)
125,5
(4.94)
212,7
(8.38)
38,1
(1.50)
C
82,6
(3.25)
B
69,9
(2.75)
A
69,9
(2.75)
181,0
(7.125)
127,0
126,9
(5.000)
(4.998)
147,6
(5.81)
9,5
(.375)
69,9
(2.75)
45VQ Series
15,7
(.62)
216,9
(8.54)
153,2
(6.03)
212,7
(8.38)
42,9
(1.69)
93,7
(3.69)
D
181,0
(7.13)
127,0
126,9
(5.000)
(4.998)
B
82,6
(3.25)
A
158,8
(6.25)
79,4
(3.125)
12,7
(.50)
147,6
(5.81)
17,5 (.69) 2 HOLES
FOR MOUNTING
16
Optional Shafts
Splined Shafts
Pump
Shaft
Code
Spline Data
(See below.)
20VQ,
20VQF,
20VQP
151
44,1 (1.62)
9,53 (.375)
11,9 (.468)
4,1 (.16)
27,8 (1.09)
11
44,5 (1.75)
9,53 (.375)
11,1 (.437)
4,1 (.16)
27,8 (1.09)
25VQ
123
44,5 (1.75)
9,53 (.375)
15,7 (.62)
4,1 (.16)
27,8 (1.09)
297
41,1 (1.62)
9,53 (.375)
7,9 (.31)
4,1 (.16)
27,8 (1.09)
11
58,7 (2.31)
9,53 (.375)
11,1 (.437)
6,4 (.25)
35,1 (1.38)
123
58,7 (2.31)
9,53 (.375)
15,2 (.60)
5,5 (.21)
35,1 (1.38)
297
55,5 (2.19)
12,7 (.500)
7,9 (.31)
6,4 (.25)
35,1 (1.38)
11
61,9 (2.44)
12,7 (.500)
14,3 (.565)
9,7 (.38)
39,6 (1.56)
130
61,9 (2.44)
12,7 (.500)
15,2 (.60)
9,9 (.39)
40,4 (1.59)
297
55,5 (2.19)
12,7 (.500)
7,9 (.31)
9,7 (.38)
39,6 (1.56)
35VQ
45VQ
Number of
Teeth
Pitch
Major Diameter
Form Diameter
Minor Diameter
Minor Diameter
13
16/32
22,17 (.873)
22,15 (.872)
19,03 (.749)
18,16 (.715)
13
16/32
21,8 (.858)
21,6 (.852)
19,03 (.749)
18,16 (.715)
Side fit
14
12/24
31,70 (1.248)
31,67 (1.247)
27,4 (1.08)
26,42 (1.040)
14
12/24
31,2 (1.229)
31,1 (1.223)
27,4 (1.08)
26,42 (1.040)
Side fit
17
D
1,5 (.06) x 45
C
A
Pump
20VQ,
20VQF,
20VQP
25VQ
35VQ
45VQ
Shaft
Code
F key width
x length
58,7 (2.31)
9,53 (.375)
11,9 (.468)
22,23 (.875)
22,20 (.874)
24,5 (.966)
24,4 (.961)
4,75 (.187)
x 32 (1.25)
58,7 (2.31)
9,53 (.375)
11,1 (.435)
22,23 (.875)
22,20 (.874)
24,5 (.966)
24,4 (.961)
4,75 (.187)
x 32 (1.25)
86
77,7 (3.06)
9,53 (.375)
11,1 (.435)
25,37 (.999)
25,35 (.998)
28,3 (1.11)
28,1 (1.10)
6,36 (.250)
x 50,8 (2.00)
203
77,7 (3.06)
9,53 (.375)
7,9 (.31)
25,40 (1.00)
25,35 (.998)
28,20 (1.11)
27,94 (1.10)
6,36 (.250)
x 49,2 (1.938)
73,2 (2.88)
9,53 (.375)
11,1 (.435)
31,75 (1.250)
31,70 (1.248)
35,36 (1.39)
34,10 (1.38)
7,94 (.313)
x 38,1 (1.50)
86
85,9 (3.38)
9,53 (.375)
11,1 (.435)
34,90 (1.374)
34,87 (1.373)
38,6 (1.52)
38,3 (1.51)
7,92 (.312)
x 54 (2.13)
203
84,1 (3.31)
12,7 (.500)
7,9 (.31)
34,90 (1.374)
34,87 (1.373)
38,6 (1.52)
38,3 (1.51)
7,92 (.312)
x 54 (2.125)
62,0 (2.44)
12,7 (.500)
14,22 (.560)
31,75 (1.250)
31,70 (1.248)
35,36 (1.39)
34,10 (1.38)
7,92 (.312)
x 28,5 (1.12))
86
87,4 (3.44)
12,7 (.500)
14,22 (.560)
38,07 (1.499)
38,05 (1.498)
42,4 (1.67)
42,1 (1.66)
9,53 (.375)
x 50,8 (2.00)
203
90,4 (3.56)
12,7 (.500)
7,9 (.31)
38,07 (1.499)
38,05 (1.498)
42,4 (1.67)
42,1 (1.66)
9,53 (.375)
x 57,1 (2.25)
18
Typical Performance
20VQ Single Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
136 (36)
129 (34)
bar (psi)
CODE
106 (28)
7 (100)
70 (1000)
114 (30)
140 (2000)
83 (22)
76 (20)
7 (100)
70 (1000)
140 (2000)
210 (3000)
68 (18)
61 (16)
53 (14)
7 (100)
70 (1000)
140 (2000)
210 (3000)
45 (12)
38 (10)
98 (26)
11
7 (100)
70 (1000)
140 (2000)
210 (3000)
91 (24)
76 (20)
68 (18)
61 (16)
53 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
1200
1600
2000
2400
0
400
2800
bar (psi)
12
83 (22)
23 (6)
800
14
91 (24)
30 (8)
0
400
7 (100)
70 (1000)
140 (2000)
160 (2300)
106 (28)
98 (26)
121 (32)
800
1200
1600
2000
2400
CODE
2800
bar (psi)
CODE
37,3 (50)
210 (3000)
11
33,6 (45)
33,6 (45)
26,1 (35)
22,4 (30)
18,6 (25)
210 (3000)
140 (2000)
11
210 (3000)
140 (2000)
5
8
70 (1000)
140 (2000)
11
5
70 (1000)
70 (1000)
7 (100)
7 (100)
7 (100)
11
8
5
14,9 (20)
11,2 (15)
7,5 (10)
3,7 (5)
0
400
800
1200
1600
2000
SPEED r/min
2400
2800
INPUT kW (hp)
INPUT kW (hp)
29,8 (40)
29,8 (40)
140 (2000) 14
160 (2300) 12
26,1 (35)
70 (1000) 12
22,4 (30)
18,6 (25)
70 (1000) 14
70 (1000) 14
14,9 (20)
11,2 (15)
7,5 (10)
3,7 (5)
0
400
7 (100)
7 (100)
800
1200
1600
2000
2400
14
12
2800
SPEED r/min
19
0,14
0,07
0,17
0,10
bar
0,07
0,14
0,21
0,28
0,34
bar
1.14
SPEED RATING
CORRECTION
FACTOR
1.12
1.10
1.08
Example:
Max. speed @ 0 psi inlet
Correction factor @ 5 in. Hg
Max. speed @ 5 in. Hg inlet
1.06
2700 r/min
x .93
2511 r/min
1.04
1.02
in. Hg
VACUUM
2
0.98
psi
1.0
2
3
4
5
SUPERCHARGE PRESSURE
0.96
0.94
0.92
0.90
0.88
0.86
7 (100)
70 (1000)
17
140 (2000)
210 (3000)
7 (100)
70 (1000) 12
140 (2000)
210 (3000)
133 (35)
114 (30)
95 (25)
76 (20)
57 (15)
151 (40)
133 (35)
114 (30)
95 (25)
38 (10)
19 (5)
1200
1600
2000
2400
0
400
2800
7 (100)
70 (1000)
140 (2000)
210 (3000)
14
57 (15)
19 (5)
800
21
76 (20)
38 (10)
0
400
7 (100)
70 (1000)
140 (2000)
210 (3000)
800
1200
1600
2000
2400
2800
67,1 (90)
210 (3000)
INPUT kW (hp)
44,7 (60)
37,3 (50)
210 (3000) 12
140 (2000) 17
29,8 (40)
140 (2000) 12
22,4 (30)
70 (1000) 17
INPUT kW (hp)
210 (3000) 17
52,2 (70)
52,2 (70)
44,7 (60)
29,8 (40)
22,4 (30)
70 (1000) 12
14,9 (20)
7,5 (10)
7 (100) 17
7 (100) 12
7,5 (10)
800
1200
1600
2000
SPEED r/min
2400
2800
210 (3000)
14
140 (2000)
21
140 (2000)
14
140 (2000)
21
140 (2000)
14
7 (100)
7 (100)
21
14
37,3 (50)
14,9 (20)
0
400
21
59,7 (80)
59,7 (80)
0
400
800
1200
1600
2000
2400
2800
SPEED r/min
20
Typical Performance
35VQ Single & 35VQT*S
Thrudrive Pumps
Performance Constants:
SAE 10W fluid @ 82C (180).
Pump inlet @ 0 psig (14.7 psia)
bar
0,14 0,07
0,10
0,17
1.12
1.10
0,28
bar
SPEED RATING
CORRECTION
FACTOR
1.04
1.02
in. Hg
2
0.98
VACUUM
1.0
2
3
4
5
SUPERCHARGE PRESSURE
psi
0.96
0.94
0.92
265 (70)
265 (70)
7 (100)
246 (65)
246 (65)
70 (1000) 35
140 (2000)
210 (3000)
227 (60)
227 (60)
208 (55)
208 (55)
7 (100)
70 (1000) 25
140 (2000)
210 (3000)
189 (50)
170 (45)
70 (1000)
140 (2000)
210 (3000)
38
7 (100)
70 (1000)
140 (2000)
210 (3000)
30
189 (50)
170 (45)
151 (40)
151 (40)
133 (35)
133 (35)
114 (30)
95 (25)
114 (30)
95 (25)
76 (20)
76 (20)
57 (15)
57 (15)
38 (10)
38 (10)
19 (5)
800
1200
1600
2000
2400
2800
400
800
1200
1600
2000
2400
2800
111,9 (150)
111,9 (150)
104,4 (140)
104,4 (140)
210 (3000) 35
96,9 (130)
89,5 (120)
82,0 (110)
82,0 (110)
210 (3000) 25
67,1 (90)
140 (2000) 35
59,7 (80)
52,2 (70)
140 (2000) 25
44,7 (60)
37,3 (50)
67,1 (90)
59,7 (80)
70 (1000) 25
2000
2400
2800
2000 PSI
30
38
29,8 (40)
70 (1000)
30
7 (100)
7 (100)
38
30
14,9 (20)
1200
1600
SPEED r/min
38
70 (1000)
22,4 (30)
800
140 (2000)
37,3 (50)
14,9 (20)
7 (100) 35
7 (100) 25
30
44,7 (60)
22,4 (30)
7,5 (10)
210 (3000)
52,2 (70)
70 (1000) 35
29,8 (40)
38
74,6 (100)
INPUT kW (hp)
74,6 (100)
210 (3000)
96,9 (130)
89,5 (120)
(0)
400
0,34
1.06
284 (75)
0,21
1.08
Example:
Max. speed @ 0 psi inlet
2500 r/min
Correction factor @ 5 in. Hg x .92
Max. speed @ 5 in. Hg inlet 2300 r/min
Pump inlet suction should not exceed 5
in. Hg vacuum. Positive pressure on inlet
should not exceed 1,4 bar (20 psi).
INPUT kW (hp)
0,14
1.14
19 (5)
400
0,07
7,5 (10)
(0)
400
800
1200
1600
2000
SPEED r/min
2400
2800
21
1.14
1.12
1.10
0,14
0,21
0,28
0,34 bar
SPEED RATING
CORRECTION
FACTOR
1.08
1.06
in. Hg
5 4 3 2
VACUUM
1.04
1.02
psi
1.0
2
3
4
5
0.98 SUPERCHARGE PRESSURE
0.96
0.94
0.92
0.90
416 (110)
0,14 0,07
0,17 0,10
bar
0.88
398 (105)
0.86
70 (1000) 60
140 (2000)
175 (2500)
379 (100)
360 (95)
360 (95)
341 (90)
341 (90)
322 (85)
322 (85)
303 (80)
303 (80)
CODE 50 PUMPS
70 (1000)
265 (70)
140 (2000)
175 (2500)
246 (65)
284 (75)
42
227 (60)
265 (70)
246 (65)
DELIVERY L/min (USgpm)
7 (100)
284 (75)
208 (55)
189 (50)
170 (45)
151 (40)
133 (35)
208 (55)
189 (50)
170 (45)
151 (40)
133 (35)
114 (30)
114 (30)
95 (25)
95 (25)
76 (20)
76 (20)
57 (15)
57 (15)
38 (10)
38 (10)
19 (5)
400
19 (5)
800
1200
1600
2000
2400
134,2 (180)
2800
400
1200
1600
2000
2400
2800
119,3 (160)
140 (2000) 60
104,4 (140)
89,5 (120)
175 (2500) 42
89,5 (120)
74,6 (100)
140 (2000) 42
59,7 (80)
70 (1000) 60
44,7 (60)
70 (1000) 42
29,8 (40)
INPUT kW (hp)
104,4 (140)
175 (2500) 50
140 (2000) 50
74,6 (100)
59,7 (80)
70 (1000) 50
44,7 (60)
29,8 (40)
7 (100) 60
7 (100) 42
14,9 (20)
0
400
800
175 (2500) 60
119,3 (160)
INPUT kW (hp)
227 (60)
800
1200
1600
2000
SPEED r/min
2400
2800
14,9 (20)
0
400
7 (100) 50
800
1200
1600
2000
SPEED r/min
2400
2800
22
Delivery
Displ.
USgpm @ cm3/r
1200 r/min (in3/r)
7 bar
(100 psi)
2520VQ 12
14
17
21
3520VQ 25
30
35
38
3525VQ 25
30
35
38
4520VQ 42
50
60
4525VQ 42
50
60
4535VQ 42
50
60
Max. Max.
r/min bar
(psi)
Typical
del.
L/min
(USgpm)
@ max.
speed &
pressure
Typical
input
kW
(hp)
@ max.
speed &
pressure
Delivery
Displ.
USgpm @ cm3/r
1200 r/min (in3/r)
7 bar
(100 psi)
Max. Max.
r/min bar
(psi)
Typical
del.
L/min
(USgpm)
@ max.
speed &
pressure
Typical
input
kW
(hp)
@ max.
speed &
pressure
Wt.
kg
(lb.)
40,2 (2.45)
45,4 (2.77)
55,2 (3.37)
67,7 (4.12)
2700
2700
2500
2500
210 (3000)
210 (3000)
210 (3000)
210 (3000)
88,5 (23)
103,8 (27)
119,2 (31)
146,2 (38)
41,0 (55)
46,6 (62.5)
51,8 (69.5)
61,9 (83)
5
8
11
12
14
18,0 (1.10)
27,4 (1.67)
36,4 (2.22)
39,5 (2.41)
45,9 (2.80)
2700
2700
2700
2700
2700
210 (3000)
210 (3000)
210 (3000)
160 (2300)
140 (2000)
42,3 (11)
65,4 (17)
88,5 (23)
98,1 (25.5)
115,4 (30)
17,9 (24)
26,1 (35)
20,5
35,4 (47.5) (45)
28,4 (38)
29,1 (39)
81,6 (4.98)
97,7 (5.96)
112,8 (6.88)
121,6 (7.42)
2500
2500
2400
2400
210 (3000)
210 (3000)
210 (3000)
210 (3000)
173,1 (45)
211,5 (55)
230,8 (60)
250,0 (65)
75,3 (101)
87,7 (117.5)
98,5 (132)
104,4 (140)
5
8
11
12
14
18,0 (1.10)
27,4 (1.67)
36,4 (2.22)
39,5 (2.41)
45,9 (2.80)
2500
2500
2500
2500
2500
210 (3000)
210 (3000)
210 (3000)
160 (2300)
140 (2000)
38,5 (10)
61,5 (16)
80,8 (21)
90,4 (23.5)
105,8 (27.5)
16,5 (22)
24,0 (32.5) 34,0
33,0 (44)
(75)
26,1 (35)
26,8 (36)
81,6 (4.98)
97,7 (5.96)
112,8 (6.88)
121,6 (7.42)
2500
2500
2400
2400
210 (3000)
210 (3000)
210 (3000)
210 (3000)
173,1 (45)
211,5 (55)
230,8 (60)
250,0 (65)
75,3 (101)
87,7 (117.5)
98,5 (132)
104,4 (140)
12
14
17
21
40,2 (2.45)
45,4 (2.77)
55,2 (3.37)
67,5 (4.12)
2500
2500
2500
2500
210 (3000)
210 (3000)
210 (3000)
210 (3000)
79,5 (21)
91,0 (24)
119,2 (31)
146,2 (38)
38,0 (51)
43,0 (58)
51,5 (69)
61,9 (83)
18,0 (1.10)
27,4 (1.67)
36,4 (2.22)
39,5 (2.41)
45,9 (2.80)
2200
2200
2200
2200
2200
210 (3000)
210 (3000)
210 (3000)
160 (2300)
140 (2000)
32,0 (8.5)
51,0 (13.5)
68,0 (18)
77,5 (20.5)
91,0 (24)
14,5 (19.5)
21,0 (28.5) 43,0
28,5 (38.5) (94)
23,0 (31)
24,0 (32)
40,2 (2.45)
45,4 (2.77)
55,2 (3.37)
67,5 (4.12)
2200
2200
2200
2200
210 (3000)
210 (3000)
210 (3000)
210 (3000)
68,0 (18)
79,5 (21)
100,0 (26.5)
125,0 (33)
33,0 (44)
38,0 (51)
45,5 (61)
54,5 (73)
46,0
(101)
81,6 (4.98)
97,7 (5.96)
112,8 (6.88)
121,6 (7.42)
2200
2200
2200
2200
210 (3000)
210 (3000)
210 (3000)
210 (3000)
145,5 (38.5)
178,0 (47)
211,5 (55)
223,0 (59)
66,5 (89)
77,5 (104)
89,5 (120)
97,0 (130)
53,6
(118)
34,5
(76)
Performance constants: SAE 10W fluid @ 82C (180 F); pump inlet @ 0 PSIG (14.7 PSIA)
Note: Outlet pressure must always be higher than inlet pressure. See page 5 for details.
23
Model Codes
Double Pump (without integral valves)
2520VQ (S) 12
1
F3 - Viton seals
3525VQ
4520VQ
4525VQ
4535VQ
Frame
Size
**20VQ
Pilot designation
2520VQ
3520VQ
11 (S) 123 CC
**25VQ
4535VQ
Code
(USgpm)
5
8
11
12
14
12
14
17
21
25
30
35
38
cm3/r
18,0
27,4
36,4
39,5
45,9
40,2
45,4
55,2
67,5
81,6
97,7
112,8
121,6
in3/r
1.10
1.67
2.22
2.41
2.80
2.45
2.77
3.37
4.12
4.98
5.96
6.88
7.42
Shaft type
Port connections
Pump series
All
All
2520VQ
All but 4535VQ
2520VQ
Code
A
AM*
C
E
F
Inlet
SAE 4-bolt flg
Metric 4-bolt flg.
SAE 4-bolt flg.
SAE 4-bolt flg.
SAE 4-bolt flg.
Outlet no.1
SAE 4-bolt flg.
Metric 4-bolt flg.
SAE str. thd.
SAE 4-bolt flg.
SAE str. thd.
Outlet no. 2
SAE 4-bolt flg.
Metric 4-bolt flg.
SAE str. thd.
SAE str. thd.
SAE 4-bolt flg.
0 (L)
10
11
Port orientation
10
Design
11
Shaft rotation
*Same as code A port connections, except metric threads for fastening flanges.
24
Model Codes
2520VQ (S)
1
2520VQ
3
3520VQ
4520VQ
Pilot designation
F3 Viton seals
10
Inlet
SAE 4-bolt flg.
SAE 4-bolt flg.
14
11
2, 4, 6, 7, 8, 10 or 12 USgpm
12
C 52 (750)
D 70 (1000)
E 86 (1250)
F 100 (1500)
13
G 121 (1750)
H 140 (2000)
J 155 (2250)
K 175 (2500)
Design
Port connections
13
10 Port orientation
(Viewed from cover end of pump)
With No.1 outlet opposite inlet:
AA - No. 2 outlet 135 CCW from inlet
AB - No. 2 outlet 45 CCW from inlet
AC - No. 2 outlet 45 CW from inlet
AD - No. 2 outlet 135 CW from inlet
With No.1 outlet 90 CCW from inlet:
BA - No. 2 outlet 135 CCW from inlet
BB - No. 2 outlet 45 CCW from inlet
BC - No. 2 outlet 45 CW from inlet
BD - No. 2 outlet 135 CW from inlet
With No.1 outlet inline with inlet:
CA - No. 2 outlet 135 CCW from inlet
CB - No. 2 outlet 45 CCW from inlet
CC - No. 2 outlet 45 CW from inlet
CD - No. 2 outlet 135 CW from inlet
With No.1 outlet 90 CW from inlet:
DA - No. 2 outlet 135 CCW from inlet
DB - No. 2 outlet 45 CCW from inlet
DC - No. 2 outlet 45 CW from inlet
DD - No. 2 outlet 135 CW from inlet
14
6
11 12
Outlet no. 1
SAE str. thd.
SAE 4-bolt flg.
Outlet(s) no. 2
SAE str. thd.
SAE str. thd.
Tank
SAE str. thd.
SAE str. thd.
Shaft rotation
25
Installation Dimensions
2520VQ Series
Dimensions in millimeters (inches)
.375 UNC-2B OR M10 THD.
19,05 (.75) DEEP 4 HOLES
63,5 (2.50)
INLET CONN.
101,6
101,5
(4.000)
(3.998)
OPTIONAL STRAIGHT
THREAD CONNECTION
1.3125-12 UN2B
THREAD FOR SAE HYD.
FITTINGS
SEE SHAFT OPTIONS
STARTING ON PAGE 30.
12,7
(.50)
19,1 (.75)
OUTLET
CONN. NO. 2
9,53
(.38)
25,4 (1.00)
OUTLET CONN. NO. 1
88,1
(3.47)
45
Z
VIEW Z-Z
120,7 (4.75)
101,6
(4.00)
38,1
(1.50)
85,9
(3.38) 84,1
(3.31)
53,8
(2.12)
D
107,7
(4.24)
Z
B
11,9
R.
(.47)
146,1(5.75)
76,2
(3.00)
76,2
(3.00)
HEIGHT OF
STRAIGHT
THREAD
CONNECTION
252,5
(9.94)
53,8
(2.12)
A
107,7
(4.24)
174,8
(6.88)
3520VQ Series
15,7
(.62)
127,0
126,9
(5.000)
(4.998)
76.2 (3.00)
INLET CONN.
.375-16 UNC-2B OR M10 THD.
19,05 (.75) DEEP 4 HOLES
.437-14 UNC-2B OR M12 THD
22,2 (.875) DEEP 4 HOLES
9,7
(.38)
31,8 (1.25)
OUTLET CONN. NO. 1
VIEW Z-Z
C
19,1 (.75)
OUTLET
CONN. NO. 2
45
Z
114,3
(4.50)
212,9
(8.38)
38,1
(1.50)
88,9
(3.50) 82,6
(3.25)
Z
B
69,9
R.
(2.75)
276,6
(10.89)
99,6
(3.92)
181,1
(7.13)
D
76,2
(3.00)
A
147.6 (5.81)
26
Installation Dimensions
3525VQ Series
Dimensions in millimeters (inches)
.437-14 UNC-2B OR M12
THD. 22,2 (.875) DEEP
9,53
(.375)
OPTIONAL STRAIGHT
THREAD CONNECTION
1.3125-12 UN-2B THREAD
FOR SAE HYD. FITTINGS
127,0
126,9
(5.000)
(4.998)
SEE SHAFT OPTIONS STARTING
ON PAGE 30.
76.2 (3.00)
INLET CONN.
31,8 (1.25)
OUTLET CONN. NO. 1
58,7 R.
(2.31)
C
VIEW Z-Z
25,4 (1.00)
OUTLET CONN.
NO. 2
12,7 R.
(.50)
109,5
(4.31)
15,7
(.62)
82,6
(3.25)
293,9
(11.57)
114,3
(4.50)
212,9
(8.38)
38,1
(1.50)
88,9
(3.50)
45
B
122,4
(4.82)
181,1
(7.13)
61,2
(2.41)
61,2
(2.41)
74,7
(2.94)
81,0
(3.19)
122,4
(4.82)
A
147.6 (5.81)
17,5 (.69) 2 HOLES
HEIGHT OF STR. THD. CONNECTION
4520VQ Series
88,9 (3.50)
INLET CONN.
OPTIONAL STRAIGHT
THREAD CONNECTION
1.0625-12 UN-2B THREAD
FOR SAE HYD. FITTINGS
SEE SHAFT OPTIONS STARTING
ON PAGE 30.
19,1 (.75)
OUTLET CONN.
NO. 2
38,1 (1.50)
OUTLET CONN. NO. 1
306,8
(12.08)
Z
VIEW Z-Z
C
79,2
(3.12)
12,7
(.50)
162,1
(6.38)
81,0
(3.19)
15,7
(.62)
119,9
(4.72)
119,4
(4.70)
42,9
(1.69)
127,0
126,9
(5.000)
(4.998)
212,9
(8.38)
93,7
(3.69)
102,4
(4.03)
45
D
B
76,2 84,1
(3.00) (3.31)
A
181,1
(7.13)
17,5 (.69) 2 HOLES
147.6 (5.81)
27
4525VQ Series
Dimensions in millimeters (inches)
4-BOLT PORT CONNECTION PADS ARE
FOR USE WITH 4-BOLT FLANGES. SEE
PAGE 119 FOR SELECTION.
OPTIONAL STRAIGHT
THREAD CONNECTION
1.3125-12 UN-2B THREAD
FOR SAE HYD. FITTINGS
38,1 (1.50)
OUTLET CONN. NO. 1
.625-11 UNC-2B OR M16 THD.
31,7 (1.25) DEEP 4 HOLES
127,0
126,9
(5.000)
(4.998)
162,1
(6.38)
81,0
(3.19)
25,4 (1.00)
OUTLET CONN.
NO. 2
119,4
(4.70)
135,9
(5.35)
Z
84,1
(3.31)
79,2
(3.12)
329,9
(12.99)
15,7
(.62)
88,9 (3.50)
INLET CONN.
93,7
(3.69)
42,9
(1.69)
212,9
(8.38)
102,4
(4.03)
45
74,7
(2.94)
181,1
(7.13)
79,2
(3.12)
HEIGHT OF STRAIGHT
THREAD CONNECTION
12,7
(.50)
147.6 (5.81)
4535VQ Series
Dimensions in millimeters (inches)
.500-13UNC-2B OR M12 THD.
23,8 (.94) DEEP 4 HOLES
127,0
126,9
(5.000)
(4.998)
31,8 (1.25)
OUTLET CONN. NO. 2
101,6 (4.00)
INLET CONN.
15,7
(.62)
38,1 (1.50)
OUTLET CONN. NO. 1
C
162,1
(6.38)
353,1 (13.90)
148,3
(5.84)
81,0
(3.19)
133,4
(5.25)
42,9
(1.69)
102,4
(4.03)
101,6
(4.00)
B
212,9
(8.38)
93,7
(3.69)
D
84,1
(3.31)
A
17,5 (.69)
2 HOLES
12,7
(.50)
181,1
(7.13)
147.6 (5.81)
28
Installation Dimensions
Model
series
A
2520VQF 265,9
(10.47)
3520VQF 289,8
(11.41)
4520VQF 320,3
(12.61)
Dimensions
B
C
D
108,7 88,1 101,6
(4.28) (3.47) (4.00)
120,1 99,6 114,3
(4.73) (3.92) (4.50)
140,5 119,9 119,4
(5.53) (4.72) (4.70)
E
38,1
(1.50)
38,1
(1.50)
42,9
(1.69)
INLET
CONNECTION
TANK CONNECTION
.875-14 UNF-2B THD.
A
45
3,2
(.125)
23,0
(.906)
98,6
(3.88)
114,3
(4.50)
Dimensions
B
C
113,0 101,6
(4.45) (4.00)
124,5 114,3
(4.90) (4.50)
144,8 119,4
(5.70) (4.70)
OUTLET
CONNECTION
NO. 1
D
38,1
(1.50)
38,1
(1.50)
42,9
(1.69)
A
124,0
(4.88)
62,0
(2.44)
56,4
(2.22)
55,4
(2.18)
29
Optional Shafts
Splined Shafts
Pump
2520VQ,
2520VQ
2520VQF,
2 20VQP
2520VQP
3520VQ,
3520VQF,
3520VQP
3520VQP,
3525VQ
4520VQ,
4520VQF
4520VQF,
4520VQP,,
4525VQ
4525VQ,
4535VQ
Shaft
Code
Spline Data
(See below.)
11
44,5 (1.75)
9,53 (.375)
11,1 (.437)
4,1 (.16)
27,8 (1.09)
123
44,5 (1.75)
9,53 (.375)
15,7 (.62)
4,1 (.16)
27,8 (1.09)
297
41,1 (1.62)
9,53 (.375)
7,9 (.31)
6,4 (.25)
27,8 (1.09)
11
58,7 (2.31)
9,53 (.375)
11,1 (.437)
6,4 (.25)
35,1 (1.38)
123
58,7 (2.31)
9,53 (.375)
15,2 (.60)
5,5 (.21)
35,1 (1.38)
297
55,5 (2.19)
12,7 (.500)
7,9 (.31)
5,5 (.21)
35,1 (1.38)
11
61,9 (2.44)
12,7 (.500)
14,3 (.565)
9,7 (.38)
39,6 (1.56)
130
61,9 (2.44)
12,7 (.500)
15,2 (.60)
9,9 (.39)
40,4 (1.59)
297
55,5 (2.19)
12,7 (.500)
7,9 (.31)
6,4 (.25)
39,6 (1.56)
Number of
Teeth
Pitch
Major Diameter
Form Diameter
Minor Diameter
Minor Diameter
13
16/32
22,17 (.873)
22,15 (.872)
19,03 (.749)
18,16 (.715)
13
16/32
21,8 (.858)
21,6 (.852)
19,03 (.749)
18,16 (.715)
Side fit
14
12/24
31,70 (1.248)
31,67 (1.247)
27,4 (1.08)
26,42 (1.040)
14
12/24
31,2 (1.229)
31,1 (1.223)
27,4 (1.08)
26,42 (1.040)
Side fit
30
Optional Shafts
D
1,5 (.06) x 45
C
A
Pump
2520VQ,
2520VQF,
2520VQP
3520VQ,
3520VQ
3520VQF,
3520VQP,
3525VQ
Q
4520VQ,
4520VQF,
4520VQP,
4525VQ
4525VQ,
4535VQ
Shaft
Code
F key width
x length
58,7 (2.31)
9,53 (.375)
11,1 (.435)
22,23 (.875)
22,20 (.874)
24,5 (.966)
24,4 (.961)
4,75 (.187)
x 32 (1.25)
86
77,7 (3.06)
9,53 (.375)
11,1 (.435)
25,37 (.999)
25,35 (.998)
28,3 (1.11)
28,1 (1.10)
6,35 (.250)
x 50,8 (2.00)
203
77,7 (3.06)
9,53 (.375)
7,9 (.31)
25,40 (1.00)
25,35 (.998)
28,20 (1.11)
27,94 (1.10)
6,35 (.250)
x 49,2 (1.938)
73,2 (2.88)
9,53 (.375)
11,1 (.435)
31,75 (1.250)
31,70 (1.248)
35,36 (1.39)
34,10 (1.38)
7,94 (.313)
x 38,1 (1.50)
86
85,9 (3.38)
9,53 (.375)
11,1 (.435)
34,90 (1.374)
34,87 (1.373)
38,6 (1.52)
38,3 (1.51)
7,92 (.312)
x 54 (2.13)
203
84,1 (3.31)
12,7 (.500)
7,9 (.31)
34,90 (1.374)
34,87 (1.373)
38,6 (1.52)
38,3 (1.51)
7,92 (.312)
x 54 (2.125)
62,0 (2.44)
12,7 (.500)
14,22 (.560)
31,75 (1.250)
31,70 (1.248)
35,36 (1.39)
34,10 (1.38)
7,92 (.312)
x 28,5 (1.12))
86
87,4 (3.44)
12,7 (.500)
14,22 (.560)
38,07 (1.499)
38,05 (1.498)
42,4 (1.67)
42,1 (1.66)
9,53 (.375)
x 50,8 (2.00)
203
90,4 (3.56)
12,7 (.500)
7,9 (.31)
38,07 (1.499)
38,05 (1.498)
42,4 (1.67)
42,1 (1.66)
9,53 (.375)
x 57,1 (2.25)
31
Typical Performance
Shaft End Pumps
2520VQ Double Pumps &
2520VQV10 Triple Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
121 (32)
106 (28)
7 (100)
70 (1000)
12
140 (2000)
210 (3000)
91 (24)
76 (20)
61 (16)
45 (12)
7 (100)
70 (1000)
21
140 (2000)
210 (3000)
151 (40)
DELIVERY L/min (USgpm)
7 (100)
70 (1000)
17
140 (2000)
210 (3000)
136 (36)
30 (8)
133 (35)
7 (100)
70 (1000)
14
140 (2000)
210 (3000)
114 (30)
95 (25)
76 (20)
57 (15)
38 (10)
19 (5)
15 (4)
0
151 (40)
0
400
400
800
1200
1600
2000
2400
800
1200
1600
2000
2400
2800
2800
74,6 (100)
67,1 (90)
210 (3000) 17
44,7 (60)
210 (3000) 12
37,3 (50)
140 (2000) 17
29,8 (40)
140 (2000) 12
INPUT kW (hp)
INPUT kW (hp)
52,2 (70)
52,2 (70)
210 (3000) 14
140 (2000) 21
44,7 (60)
37,3 (50)
140 (2000) 14
29,8 (40)
70 (1000) 21
70 (1000) 14
22,4 (30)
22,4 (30)
70 (1000) 17
70 (1000) 12
14,9 (20)
14,9 (20)
7,5 (10)
7,5 (10)
0
400
210 (3000) 21
59,7 (80)
59,7 (80)
7 (100) 17
7 (100) 12
800
1200
1600
SPEED r/min
2000
2400
2800
0
400
7 (100) 21
7 (100) 14
800
1200
1600
2000
2400
2800
SPEED r/min
32
Typical Performance
Shaft End Pumps
3520VQ & 3525VQ Double Pumps,
352*VQV10Triple Pumps,
3525VQT Double Thru-drive Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
273 (72)
288 (76)
7 (100)
273 (72)
257 (68)
242 (64)
257 (68)
70 (1000) 35
140 (2000)
210 (3000)
227 (60)
242 (64)
197 (52)
7 (100)
212 (56)
182 (48)
70 (1000) 35
140 (2000)
210 (3000)
197 (52)
167 (44)
151 (40)
136 (36)
121 (32)
106 (28)
167 (44)
151 (40)
136 (36)
121 (32)
106 (28)
76 (20)
91 (24)
61 (16)
76 (20)
45 (12)
61 (16)
30 (8)
45 (12)
15 (4)
30 (8)
800
1200
1600
2000
2400
15 (4)
400
2800
70 (1000) 30
140 (2000)
210 (3000)
182 (48)
91 (24)
0
400
7 (100)
227 (60)
212 (56)
38
140 (2000)
210 (3000)
800
1200
1600
2000
2400
2800
111,9 (150)
104,4 (140)
104,4 (140)
210 (3000) 35
96,9 (130)
89,5 (120)
89,5 (120)
82,0 (110)
82,0 (110)
210 (3000) 25
INPUT kW (hp)
67,1 (90)
140 (2000) 35
59,7 (80)
52,2 (70)
140 (2000) 25
44,7 (60)
37,3 (50)
210 (3000) 30
74,6 (100)
INPUT kW (hp)
74,6 (100)
210 (3000) 38
96,9 (130)
140 (2000) 38
67,1 (90)
140 (2000) 30
59,7 (80)
52,2 (70)
44,7 (60)
37,3 (50)
70 (1000) 38
70 (1000) 30
70 (1000) 35
29,8 (40)
29,8 (40)
70 (1000) 25
22,4 (30)
7,5 (10)
0
400
22,4 (30)
14,9 (20)
14,9 (20)
7 (100) 35
7 (100) 25
800
1200
1600
2000
SPEED r/min
2400
2800
7 (100) 38
7 (100) 30
7,5 (10)
0
400
800
1200
1600
2000
2400
2800
SPEED r/min
33
7 (100)
398 (105)
322 (85)
322 (85)
303 (80)
303 (80)
284 (75)
7 (100)
284 (75)
70 (1000)
265 (70)
140 (2000)
175 (2500)
246 (65)
42
227 (60)
208 (55)
189 (50)
170 (45)
70 (1000) 50
140 (2000)
175 (2500)
265 (70)
246 (65)
227 (60)
208 (55)
189 (50)
170 (45)
151 (40)
151 (40)
133 (35)
133 (35)
114 (30)
114 (30)
95 (25)
95 (25)
76 (20)
76 (20)
57 (15)
57 (15)
38 (10)
38 (10)
400
7 (100)
341 (90)
341 (90)
360 (95)
140 (2000)
175 (2500)
360 (95)
CODE 50 PUMPS
70 (1000) 60
379 (100)
800
1200
1600
2000
2400
19 (5)
400
2800
800
1200
1600
2000
2400
2800
134,2 (180)
119,3 (160)
104,4 (140)
140 (2000) 60
104,4 (140)
175 (2500) 50
89,5 (120)
175 (2500) 42
89,5 (120)
140 (2000) 50
74,6 (100)
140 (2000) 42
59,7 (80)
70 (1000) 60
44,7 (60)
INPUT kW (hp)
INPUT kW (hp)
175 (2500) 60
119,3 (160)
74,6 (100)
59,7 (80)
70 (1000) 50
44,7 (60)
70 (1000) 42
29,8 (40)
29,8 (40)
14,9 (20)
0
400
7 (100) 60
7 (100) 42
800
1200
1600
2000
SPEED r/min
2400
2800
14,9 (20)
0
400
7 (100) 50
800
1200
1600
2000
2400
2800
SPEED r/min
34
Typical Performance
Cover-end Pumps of
2520VQ Double Pumps &
Center Pumps of 2520VQV10
Triple Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
7 (100)
70 (1000) 14
140 (2000)
121 (32)
114 (30)
83 (22)
76 (20)
68 (18)
61 (16)
53 (14)
45 (12)
38 (10)
7 (100)
70 (1000)
140 (2000)
210 (3000)
7 (100)
70 (1000)
140 (2000)
210 (3000)
98 (26)
DELIVERY L/min (USgpm)
7 (100)
70 (1000) 11
140 (2000)
210 (3000)
91 (24)
91 (24)
83 (22)
76 (20)
68 (18)
61 (16)
53 (14)
45 (12)
38 (10)
30 (8)
30 (8)
23 (6)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
0
400
800
1200
1600
2000
2400
37,3 (50)
0
400
2800
800
1200
1600
2000
2400
2800
210 (3000) 11
33,6 (45)
33,6 (45)
29,8 (40)
29,8 (40)
210 (3000) 8
140 (2000) 11
26,1 (35)
22,4 (30)
210 (3000)
140 (2000)
18,6 (25)
5
8
14,9 (20)
70 (1000) 11
140 (2000) 5
11,2 (15)
7,5 (10)
70 (1000)
70 (1000)
3,7 (5)
0
400
800
1200
1600
2000
SPEED r/min
2400
2800
7 (100) 11
7 (100) 8
7 (100) 5
140 (2000) 14
160 (2300) 12
26,1 (35)
INPUT kW (hp)
INPUT kW (hp)
7 (100)
70 (1000)
140 (2000) 12
160 (2300)
106 (28)
98 (26)
70 (1000) 12
22,4 (30)
18,6 (25)
14,9 (20)
70 (1000) 14
70 (1000) 14
11,2 (15)
7,5 (10)
3,7 (5)
0
400
7 (100) 14
7 (100) 12
800
1200
1600
2000
SPEED r/min
2400
2800
35
136 (36)
129 (34)
121 (32)
CODE 5, 8 & 11 PUMPS
114 (30)
91 (24)
7 (100)
70 (1000) 11
140 (2000)
210 (3000)
83 (22)
76 (20)
7 (100)
70 (1000)
140 (2000)
210 (3000)
68 (18)
61 (16)
53 (14)
7 (100)
70 (1000)
140 (2000)
210 (3000)
45 (12)
38 (10)
98 (26)
98 (26)
83 (22)
76 (20)
68 (18)
61 (16)
53 (14)
5
45 (12)
38 (10)
23 (6)
30 (8)
15 (4)
23 (6)
8 (2)
15 (4)
800
1200
1600
2000
2400
7 (100)
70 (1000) 12
140 (2000)
160 (2300)
91 (24)
30 (8)
0
400
7 (100)
70 (1000) 12
140 (2000)
106 (28)
8 (2)
400
2800
800
1200
1600
2000
2400
2800
37,3 (50)
210 (3000) 11
29,8 (40)
29,8 (40)
26,1 (35)
26,1 (35)
210 (3000) 8
140 (2000) 11
22,4 (30)
18,6 (25)
210 (3000)
140 (2000)
14,9 (20)
11,2 (15)
140 (2000) 5
70 (1000) 11
140 (2000) 8
70 (1000) 5
7,5 (10)
3,7 (5)
0
400
5
8
800
1200
1600
2000
SPEED - r/min
2400
2800
7 (100) 11
7 (100) 8
7 (100) 5
INPUT kW (hp)
INPUT kW (hp)
33,6 (45)
140 (2000) 14
160 (2300) 12
140 (2000) 12
22,4 (30)
18,6 (25)
14,9 (20)
70 (1000) 14
70 (1000) 12
11,2 (15)
7,5 (10)
3,7 (5)
0
400
7 (100) 14
7 (100) 12
800
1200
1600
2000
SPEED - r/min
2400
2800
36
Typical Performance
Cover-end Pumps of
3525VQ Double Pumps &
Center Pumps of 3525VQV10
Triple Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
167 (44)
CODE 12 & 17 PUMPS
7 (100)
70 (1000) 17
140 (2000)
210 (3000)
121 (32)
106 (28)
7 (100)
70 (1000) 12
140 (2000)
210 (3000)
91 (24)
76 (20)
61 (16)
136 (36)
DELIVERY L/min (USgpm)
151 (40)
136 (36)
106 (28)
91 (24)
30 (8)
1600
2000
2400
15 (4)
2800
14
61 (16)
30 (8)
1200
7 (100)
70 (1000)
140 (2000)
210 (3000)
76 (20)
45 (12)
800
21
121 (32)
45 (12)
15 (4)
400
7 (100)
70 (1000)
140 (2000)
210 (3000)
400
800
1200
1600
2000
2400
2800
67,1 (90)
59,7 (80)
52,2 (70)
37,3 (50)
29,8 (40)
140 (2000) 12
22,4 (30)
INPUT kW (hp)
INPUT kW (hp)
210 (3000) 12
140 (2000) 17
44,7 (60)
37,3 (50)
70 (1000) 12
14
21
140 (2000)
14
22,4 (30)
70 (1000)
21
14,9 (20)
70 (1000)
14
7 (100)
7 (100)
21
14
7,5 (10)
7,5 (10)
0
400
210 (3000)
140 (2000)
29,8 (40)
70 (1000) 17
14,9 (20)
21
52,2 (70)
210 (3000) 17
44,7 (60)
210 (3000)
800
1200
1600
2000
SPEED - r/min
2400
2800
7 (100) 17
7 (100) 12
0
400
800
1200
1600
2000
SPEED - r/min
2400
2800
37
Coverend Pumps of
4520VQ Double Pumps &
Center Pumps of 4520VQV10
Triple Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
106 (28)
7 (100)
70 (1000)
140 (2000)
98 (26)
CODE 5, 8 & 11 PUMPS
91 (24)
68 (18)
61 (16)
53 (14)
45 (12)
38 (10)
30 (8)
7 (100)
70 (1000)
140 (2000)
210 (3000)
11
7 (100)
70 (1000)
140 (2000)
210 (3000)
7 (100)
70 (1000)
140 (2000)
210 (3000)
76 (20)
61 (16)
53 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
800
1200
1600
2000
2400
8 (2)
400
2800
210 (3000)
1200
1600
2000
2400
26,1 (35)
14,9 (20)
11,2 (15)
7,5 (10)
3,7 (5)
800
1200
1600
2000
SPEED - r/min
2400
210 (3000)
140 (2000)
8
11
210 (3000)
140 (2000)
140 (2000)
70 (1000)
70 (1000)
70 (1000)
7 (100)
7 (100)
7 (100)
2800
5
8
5
11
8
5
11
8
5
22,4 (30)
INPUT kW (hp)
18,6 (25)
0
400
800
2800
11
26,1 (35)
22,4 (30)
12
68 (18)
15 (4)
29,8 (40)
INPUT kW (hp)
76 (20)
23 (6)
8 (2)
400
7 (100)
70 (1000)
140 (2000)
210 (3000)
83 (22)
83 (22)
14
18,6 (25)
140 (2000)
160 (2300)
14
12
140 (2000)
12
70 (1000)
70 (1000)
14
12
7 (100)
7 (100)
14
12
14,9 (20)
11,2 (15)
7,5 (10)
3,7 (5)
0
400
800
1200
1600
2000
SPEED - r/min
2400
2800
38
Typical Performance
Cover-end Pumps of 4525VQ Double
Pumps, Center Pumps of 4525VQV10
Triple Pumps, Rear Pumps of 4525VQT
Double Thrudrive Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
151 (40)
121 (32)
106 (28)
91 (24)
76 (20)
61 (16)
17
12
45 (12)
136 (36)
30 (8)
15 (4)
400
121 (32)
106 (28)
7 (100)
70 (1000) 14
140 (2000)
210 (3000)
91 (24)
76 (20)
61 (16)
45 (12)
30 (8)
800
1200
1600
2000
2400
15 (4)
400
2800
800
1200
1600
2000
2400
2800
59,7 (80)
52,2 (70)
17
29,8 (40)
210 (3000)
140 (2000)
12
17
22,4 (30)
140 (2000)
12
14,9 (20)
70 (1000)
70 (1000)
17
12
INPUT kW (hp)
37,3 (50)
7,5 (10)
7 (100)
7 (100)
800
1200
1600
2000
SPEED - r/min
2400
2800
17
12
INPUT kW (hp)
210 (3000)
44,7 (60)
0
400
210 (3000) 21
52,2 (70)
44,7 (60)
210 (3000) 14
140 (2000) 21
37,3 (50)
29,8 (40)
140 (2000) 14
22,4 (30)
70 (1000) 21
14,9 (20)
70 (1000) 14
7,5 (10)
0
400
7 (100) 21
7 (100) 14
800
1200
1600
2000
2400
2800
SPEED - r/min
39
Cover-end Pumps of
4535VQ Double Pumps &
Center Pumps of 4535VQV10
Triple Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
242 (64)
7 (100)
7 (100)
242 (64)
70 (1000)
35
140 (2000)
210 (3000)
227 (60)
70 (1000)
38
140 (2000)
210 (3000)
227 (60)
212 (56)
182 (48)
7 (100)
70 (1000) 25
140 (2000)
210 (3000)
151 (40)
136 (36)
121 (32)
106 (28)
197 (52)
167 (44)
212 (56)
7 (100)
197 (52)
70 (1000) 30
140 (2000)
210 (3000)
182 (48)
167 (44)
151 (40)
136 (36)
121 (32)
106 (28)
91 (24)
91 (24)
76 (20)
76 (20)
61 (16)
61 (16)
45 (12)
45 (12)
30 (8)
400
800
1200
1600
2000
2400
257 (68)
30 (8)
400
2800
800
1200
1600
2000
2400
96,9 (130)
82,0 (110)
82,0 (110)
74,6 (100)
74,6 (100)
67,1 (90)
210 (3000) 25
67,1 (90)
59,7 (80)
140 (2000) 35
59,7 (80)
52,2 (70)
140 (2000) 25
44,7 (60)
37,3 (50)
29,8 (40)
22,4 (30)
210 (3000) 30
140 (2000) 38
52,2 (70)
140 (2000) 30
44,7 (60)
37,3 (50)
70 (1000) 35
29,8 (40)
70 (1000) 25
22,4 (30)
70 (1000) 38
70 (1000) 30
14,9 (20)
14,9 (20)
7,5 (10)
0
400
210 (3000) 38
89,5 (120)
210 (3000) 35
INPUT kW (hp)
INPUT kW (hp)
89,5 (120)
2800
7 (100) 35
7 (100) 25
800
1200
1600
2000
SPEED - r/min
2400
2800
7,5 (10)
0
400
7 (100) 38
7 (100) 30
800
1200
1600
2000
SPEED - r/min
2400
2800
40
Typical Performance
Controlled Flow
Integral Valves (cover end)
Models 2520VQF, 3520VQF &
4520VQF Double Pumps
Performance Constants:
SAE 10W fluid @ 82C (180F)
Pump inlet @ 0 psig (14.7 psia)
68 (18)
68 (18)
61 (16)
53 (14)
L/min (USgpm)
45 (12)
38 (10)
45 (12)
38 (10)
23 (6)
30 (8)
27 (7)
23 (6)
15 (4)
15 (4)
30 (8)
8 (2)
8 (2)
0
600 800
CODE 5 PUMP
76 (20)
1200
1600
61 (16)
L/min (USgpm)
53 (14)
45 (12)
45 (12)
38 (10)
38 (10)
30 (8)
27 (7)
23 (6)
30 (8)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
0
600 800
2000
2400 2700
PUMP SPEED - r/min
1200
1600
2000
2400 2700
PUMP SPEED - r/min
CODE 11 PUMP
CODE 12 PUMP
121 (32)
106 (28)
91 (24)
76 (20)
L/min (USgpm)
45 (12)
61 (16)
38
30
27
23
15
8
45 (12)
30 (8)
15 (4)
0
600 800
1200
1600
(10)
(8)
(7)
(6)
(4)
(2)
121 (32)
106 (28)
91 (24)
76 (20)
L/min
45
38
30
27
23
15
8
61 (16)
45 (12)
30 (8)
15 (4)
0
600 800
2000
2400 2700
PUMP SPEED - r/min
1200
1600
(USgpm)
(12)
(10)
(8)
(7)
(6)
(4)
(2)
2000
2400 2700
PUMP SPEED - r/min
106 (28)
91 (24)
76 (20)
L/min
45
38
30
27
23
15
8
61 (16)
45 (12)
30 (8)
15 (4)
0
600 800
1200
1600
2000
2400 2700
PUMP SPEED - r/min
(USgpm)
(12)
(10)
(8)
(7)
(6)
(4)
(2)
CODE 14 PUMP
121 (32)
140 (2000)
100 (1500)
70 (1000)
35 (500)
18,0
(5)
37,9
(10)
56,8
(15)
75,7
(20)
94,6
25
113,6
(30)
41
2520VQ Series
0,14
0,07
0,10
bar 0,17
0,07
0,14
0,21
0,28
0,34
bar
bar
0,14
0,07
0,17
0,10
1.10
in. Hg
1.12
SPEED RATING
CORRECTION
FACTOR
1.10
1.08
1.08
1.06
1.06
1.04
1.04
1.02
5
in. Hg
VACUUM
0,21
0,28
0,34
bar
0.98
1.0
2
3
4
5
SUPERCHARGE PRESSURE
psi
SPEED RATING
CORRECTION
FACTOR
1.02
5
VACUUM
2
1.0
0.98
0.96
0.96
0.94
0.94
0.92
0.92
0.90
2
3
4
5
SUPERCHARGE PRESSURE
psi
0.90
0.88
0.88
0.86
0.86
Maximum operating speeds shown on performance curves are for pumps
operating at 0 psi inlet condition. To compute maximum operating speeds
at other inlet conditions use the appropriate speed rating correction factor
shown in the curve above.
0,14
1.14
1.14
1.12
0,07
2700 r/min
X .93
2511 r/min
EXAMPLE:
2200 r/min
X .91
2002 r/min
Pump inlet suction should not exceed 5 in. Hg vacuum. Positive pressure
on inlet should not exceed 1.4 bar (20 psi).
Pump inlet suction should not exceed 5 in. Hg vacuum. Positive pressure
on inlet should not exceed 1.4 bar (20 psi).
0,14
0,07
0,17 0,10
0,07
0,14
0,21
0,28
0,34
bar
1.14
1.12
1.10
SPEED RATING
CORRECTION
FACTOR
1.08
1.06
1.04
in. Hg
1.02
5
VACUUM
2
0.98
1.0
2
3
4
5
SUPERCHARGE PRESSURE
psi
0.96
0.94
0.92
0.90
0.88
0.86
2500 r/min
X .92
2300 r/min
Pump inlet suction should not exceed 5 in. Hg vacuum. Positive pressure
on inlet should not exceed 1.4 bar (20 psi).
42
2520VQSV10
3520VQSV10
3525VQSV10
4525VQSV10
4535VQSV10
1
2
3
4
2700
2700
2700
2700
2500
2500
2500
2500
2200
2200
2200
2200
2200
2200
2200
2200
2700
2500
2200
2200
2200*
2500+
1900*
2200+
2200*
2500+
1900*
2200+
2500
2500
2500
2200*
2500+
2200*
2500+
2200*
2400+
2200
2200
2200
2000*
2200+
2100*
2200+
Typical Performance
For triple pump performance, use
curves listed in this table:
Triple pump
model series
Shaft end
pump
2520VQSV10
25**VQ
Center
pump
Cover end
pump
**20VQ
V10
3520VQSV10
35**VQ
**20VQ
V10
3525VQSV10
35**VQ
**25VQ
V10
4525VQSV10
45**VQ
**25VQ
V10
4535VQSV10
45**VQ
**35VQ
V10
Page no.
32
35
73, 76, 77
33
36
73,
33
37
73,
34
39
73,
34
40
73,
76, 77
76, 77
76, 77
76, 77
43
Model Codes
Triple Pump
F3 Viton seals
Omit if not required.
1
4525VQ
4535VQ
SAE mounting
10
11
12
13
12
14
17
Splined shaft
297 All series
15
16
17
18
19
13
No. 1 outlet port position
Refer to table 2.
14
Design
Subject to change. Installation
dimensions remain the same for
designs -20 through -29.
18
15
19
Shaft rotation
(Viewed from shaft end of pump)
L Left hand (counterclockwise)
R Right hand
S Standard cover
F Integral flow control & relief valve
P Integral priority valve & relief
6
Table 1
Rated Flow @ 1200 r/min & 100 psi
Shaftend Shaftend Shaftend
pump
pump
pump
35**
2520
45**
12
14
17
21
25
30
35
38
42
50
60
5
8
11
12
14
Refer to table 1.
11 Shaft seal
S
Double seal
Blank Single seal
Table 2
Outlet position code
Position viewed
from cover end
Opposite inlet
135 CCW from inlet
90 CCW from inlet
45 CCW from inlet
Inline with inlet
45 CW from inlet
90 CW from inlet
135 CW from inlet
USgpm
Center
pump
**20
13
No. 1 outlet
A
Center
pump
**25
Center
pump
**35
12
14
17
21
25
30
35
38
14
No. 2 outlet
A (4535 only)
A
B (4535 only)
B
C (4535 only)
C
D (4535 only)
D
Coverend
pump
V10
1
2
3
4
5
6
7
15
No. 3 outlet
A
44
Installation Dimensions
Triple Pumps
A
V10 PORTS
B
OUTLET NO. 2 TURNED
THROUGH 45 FOR ALL
TRIPLE PUMPS EXCEPT
4535VQSV10
OUTLET NO. 3
OUTLET NO. 1
OUTLET NO. 2
INLET
SEE SHAFT
DIMENSIONS,
PAGE 46
TANK RETURN
A
B
OUTLET
A
OUTLET NO. 2 TURNED
THROUGH 45 FOR ALL
TRIPLE PUMPS EXCEPT
4535VQSV10
SECONDARY
OUTLET
PRIMARY
OUTLET
TANK RETURN
V10 cover can be assembled in any of four positions; see model codes, page 44. 4535VQSV10 shown.
Model
series
2520VQSV10
2520VQSV10F
2520VQSV10P
3520VQSV10
3520VQSV10F
3520VQSV10P
3525VQSV10
3525VQSV10F
3525VQSV10P
4525VQSV10
4525VQSV10F
4525VQSV10P
4535VQSV10
4535VQSV10F
4535VQSV10P
1, 2 & 3 USgpm*
A
B
350 (13.78)
363 (14.30)
364 (14.35)
372 (14.66)
386 (15.18)
387 (15.23)
381 (15.00)
394 (15.52)
395 (15.57)
420 (16.53)
433 (17.05)
434 (17.10)
445 (17.50)
458 (18.02)
459 (18.07)
87 (3.43)
105 (4.12)
105 (4.12)
87 (3.43)
105 (4.12)
105 (4.12)
86 (3.40)
104 (4.09)
104 (4.09)
86 (3.40)
104 (4.09)
104 (4.09)
84 (3.31)
102 (4.00)
102 (4.00)
Dimensions mm (in.)
4 & 5 USgpm*
A
B
356 (14.03)
370 (14.55)
371 (14.60)
379 (14.91)
392 (15.43)
393 (15.48)
387 (15.25)
401 (15.77)
402 (15.82)
426 (16.78)
439 (17.30)
441 (17.35)
451 (17.75)
464(18.27)
465 (18.32)
94 (3.68)
111 (4.38)
111 (4.38)
94 (3.68)
111 (4.37)
111 (4.37)
93 (3.65)
110 (4.34)
110 (4.34)
93 (3.65)
110 (4.34)
110 (4.34)
90 (3.56)
108 (4.25)
108 (4.25)
6 & 7 USgpm*
A
B
361 (14.23)
375 (14.75)
376 (14.80)
384 (15.11)
397 (15.63)
398 (15.68)
392 (15.45)
406 (15.97)
407 (16.02)
431 (16.98)
445 (17.50)
446 (17.55)
456 (17.95)
469 (18.47)
470 (18.52)
99 (3.88)
116 (4.58)
116 (4.58)
99 (3.88)
116 (4.57)
116 (4.57)
98 (3.85)
115 (4.54)
115 (4.54)
98 (3.85)
115 (4.54)
115 (4.54)
96 (3.76)
113 (4.45)
113 (4.45)
* SAE rated flows (@1200 rpm and 100 psi) of V10, V10F & V10P cover-end pump (see page 67).
For detailed dimensions of double pump end, see pages 26 through 28; for V10 series cover-end
pump, see pages 69 and 70.
45
2520VQSV10
352*VQSV10
45**VQSV10
41,1 (1.62)
55,4 (2.18)
55,4 (2.18)
7,9 (.31)
7,9 (.31)
7,9 (.31)
27,7 (1.09)
35,1 (1.38)
40,4 (1.59)
Model
C DIA.
No. of
teeth
13
Pitch
16/32
352*VQSV10
14
12/24
45**VQSV10
14
12/24
Major
dia.
21,8 (.858)
21,6 (.852)
31,2 (1.229)
31,1 (1.223)
31,2 (1.229)
31,1 (1.223)
Form
dia.
19,0
(.749)
27,4
(1.08)
27,4
(1.08)
Minor
dia.
Fit
18,16
(.715)
26,4
Side fit
(1.040)
26,4
(1.040)
Designation
Max. torque
capability
Nm (lb-in)
2520VQSV10
344 (3040)
352*VQSV10
791 (7000)
45**VQSV10
1017 (9000)
46
Delivery USgpm
@ 1200 r/min
7 bar (100 psi)
25VQT*S
12
14
17
21
25
30
35
38
42
50
60
35VQT*S
45VQT*S
Displ.
cm3/r
(in3/r)
Max.
r/min
Max.
bar
(psi)
Typical del.
L/min (USgpm)
@ max.
speed &
pressure
Typical input
kW (hp)
@ max.
speed &
pressure
40,2 (2.45)
45,4 (2.77)
55,2 (3.37)
67,5 (4.12)
2700
2700
2500
2500
210 (3000)
210 (3000)
210 (3000)
210 (3000)
88,5 (23)
103,8 (27)
119,2 (31)
146,2 (38)
41,0 (55)
46,6 (62.5)
51,8 (69.5)
61,9 (83)
81,6 (4.98)
97,7 (5.96)
112,8 (6.88)
121,6 (7.42)
138,7 (8.46)
162,3 (9.90)
193,4 (11.80)
2500
2500
2400
2400
2200
2200
2200
210 (3000)
210 (3000)
210 (3000)
210 (3000)
175 (2500)
175 (2500)
175 (2500)
173,1 (45)
211,5 (55)
230,8 (60)
250,0 (65)
255,8 (66.5)
303,8 (79)
369,2 (96)
75,3 (101)
87,7 (117.5)
98,5 (132)
104,4 (140)
91,4 (122.5)
105,2 (141)
126,8 (170)
Approx.
Wt.
kg
(lb.)
19,5 (43)
28,6 (63)
38,2 (84)
Performance constants:
Typical Performance
For thru-drive performance, use
curves on the following pages:
Thrudrive
model series
Page no.
25VQT*S
35VQT*S
45VQT*S
20
21
22
47
Model Codes
F3 Viton seals
Omit if not required.
26VQT
36VQT
Code
A
B
BP
C
SAE Designation
J744C
J744 Oct83
A
82-2
B
101-2
Special mounting with spacer
for Vickers PVE12/19/21
C
127-2
(not available on 25VQT)
Model
series
2*VQT
3*VQT
45VQT
SAE Designation
J744C
B
C
C
10
Series
Code
cm3/r
(in3/r)
2*VQT
12
14
17
21
40,2
45,4
55,2
67,5
(2.45)
(2.77)
(3.37)
(4.12)
3*VQT
25
30
35
38
81,6
97,7
112,8
121,6
(4.98)
(5.96)
(6.88)
(7.42)
Thru-drive connection
mounting adapter (2-bolt)
25VQT
35VQT
45VQT
Geometric displacement
Code = SAE rating USgpm at 1200 r/min
J744 Oct83
101-2
127-2
127-2
45VQT
42
50
60
138,7
162,3
193,4
(8.46)
(9.90)
(11.80)
11
12
Shaft type
203 - Heavy duty straight key
297 - Splined
11
Outlet positions
(Viewed from cover end of pump)
A Opposite inlet
B 90 CCW from inlet
C In line with inlet
D 90 CW from inlet
12
14
10
13
Rotated 45
Rotated 90
CCW with
with respect
respect to
pump mtg. flg. to pump mtg. flg.
Design
Subject to change. Installation
dimensions remain the same for
designs -20 through -29.
13
14
Shaft rotation
(Viewed from shaft end of pump)
L Left hand (counterclockwise)
R Right hand (clockwise)
NOTE:
For options other than listed above,
i.e. shafts, ports, displacements
and mountings, contact your
Vickers representative.
48
Installation Dimensions
25VQT*S Series
Dimensions in millimeters (inches)
Shaft options are shown on page 56.
See page 119 for selection of SAE 4-bolt
flanges for port connection pads.
63,5 (2.50)
inlet port
connection
44,5
(1.75)
26,2
(1.03)
88,9
(3.50)
25,4 (1.00)
outlet port
connection
.37516 UNC2B Thd.
.75 deep, or M10 thd.
.79 deep, 4 holes
13,1
(.52)
52,4
(2.06)
9,7
(.38)
26,2
(1.03)
A"
See chart on pages 5254.
111,1
(4.38)
101,6 (4.00)
12,7
(.50)
174,8
(6.88)
38,1
(1.50)
87,4
(3.44)
41,1
(1.62)
76,2
(3.00)
84,1
(3.31)
27,7 (1.09)
7,9
(.31)
14,2 (.56)
120,7
(4.75)
73,2
(2.88)
146,1
(5.75)
49
35VQT*S Series
Dimensions in millimeters (inches)
Shaft options are shown on page 56.
See page 119 for selection of SAE 4-bolt
flanges for port connection pads.
53,1
(2.09)
29,5
(1.16)
106,4
(4.19)
58,7
(2.31)
127,0 (5.00)
12,7
(.50)
31,8 (1.25) outlet
port connection
.43714 UNC2B thd.
.88 deep, or M12 thd.
.88 deep, 4 holes
15,0
(.59)
15,7
(.62)
30,2
(1.19)
A"
See chart on pages 5255.
122,2
(4.81)
38,1
(1.50)
212,9
(8.38)
55,4
(2.18)
106.2
(4.18)
83,8
(3.3)
35,1 (1.38)
7,9
(.31)
88,9
(3.5)
17,5
(.69)
147,6
(5.81)
90,4
(3.56)
181,1
(7.13)
50
Installation Dimensions
45VQT*S Series
Dimensions in millimeters (inches)
Shaft options are shown on page 56.
See page 119 for selection of SAE 4-bolt
flanges for port connection pads.
.625-11 UNC-2B or
M16 thd.
31,8 (1.25) deep
4 holes
69,9
(2.75)
35,1
(1.38)
88,9 (3.50)
inlet port
connection
35,1
(1.38)
60,5
(2.38)
127,0 (5.00)
69,9
(2.75)
120,7
(4.75)
12,7
(.50)
17,8
(.70)
38,1 (1.50)
outlet port
connection
35,8
(1,41)
15,7
(.62)
A"
See chart on pages 5255
129,8
(5.11)
42,9
(1.69)
212,9 (8.38)
55,4
(2.18)
106.4
(4.19)
102,4
(4.03)
93,7
(3.69)
17,5
(.69)
thru
2 holes
39,6
(1.56)
7,9
(.31)
90,4
(3.56)
181,1
(7.13)
147,6
(5.81)
51
A rear mounting
Dimensions in millimeters (inches)
This unit accepts a hydraulic pump with
a mounting configuration of the 82-2 (A)
size per SAE std. J-744 Oct83. The
output coupling is for a pump shaft of
SAE A size with a 30 involute spline
(per SAE std J-744 Oct83), 9T and
16/32 D.P. (Per ANSI B.92.1a1976).
Concentricity of the shaft of the
attached pump must meet or exceed
requirements of SAE Std. J-744 Oct83.
A"
To mounting flange
face
133.4
(5.25)
6,6
(.26)
66,5
(2.62)
1,5
(.06)
66,5
(2.62)
53,1
(2.09)
106,4
(4.19)
Pump
model
82,6
(3.25)
50,8
(2.00)
45
Output coupling
130,3
(5.13)
Dimension A
Dimension L *
25VQTAS
236, 2 (9.3)
32,5/31,0 (1.28/1.22)
33,0 (1.30) maximum
35VQTAS
259,1 (10.2)
32,5/31,0 (1.28/1.22)
35,6 (1.40) maximum
45VQTAS
292,1 (11.5)
32,5/31,0 (1.28/1.22)
35,3 (1.39) maximum
L"
Snap ring
AS 568
230
Oring
required
52
B rear mounting
Dimensions in millimeters (inches)
This unit accepts a hydraulic pump with
a mounting configuration of the 101-2
(B) size per SAE std. J-744 Oct83. The
output coupling is for a pump shaft of
SAE B size with a 30 involute spline
(per SAE std J-744 Oct83), 13T and
16/32 D.P. (Per ANSI B.92.1a1976).
Concentricity of the shaft of the
attached pump must meet or exceed
requirements of SAE Std. J-744 Oct83.
.50013
UNC2B thd.
.760 thru
flange, 2
holes
Output
coupling
174,8
(6.88)
A"
To mounting flange face
5,8
(.23)
66,5
(2.62)
9,9
(.39)
101,6
(4.00)
56,6
(2.23)
133,4
(5.25)
84,1
(3.31)
Snap ring
72,6
(2.86)
L"
AS 568234
Oring required
146,1
(5.75)
NOTE:
For mounting PVE12/19/21,
use BP adapter.
Pump
model
Dimension A
Dimension L *
25VQTBS
246,4 (9.7)
42,4/39,9 (1.67/1.57)
45,2 (1.78) maximum
35VQTBS
269,2 (10.6)
42,4/39,9 (1.67/1.57)
46,7 (1.84) maximum
45VQTBS
299,7 (11.8)
42,4/39,9 (1.67/1.57)
46,2 (1.82) maximum
53
BP rear mounting
Dimensions in millimeters (inches)
This SAE B size unit with spacer
accepts a Vickers PVE12/19/21
pump.The output coupling is for a pump
shaft of SAE B size with a 30 involute
spline (per SAE std J-744 Oct83), 13T
and 16/32 D.P. (Per ANSI B.92.1a1976).
174,8
(6.88)
A
To mounting flange face
Snap ring
66,5
(2.62)
Output
coupling
10,2
(.40)
101,6
(4.00)
63,5
(2.50)
133,4
(5.25)
84,1
(3.31)
AS 568155
Oring required
73,2
(2.86)
146,1
(5.75)
Pump
model
Dimension A
AS 568234
O-ring required
Dimension L *
25VQTBPS
261,9 (10.31)
45,7/43,2 (1.80/1.70)
Not SAE std.
35VQTBPS
284,5 (11.20)
45,7/43,2 (1.80/1.70)
Not SAE std.
45VQTBPS
317,0 (12.48)
45,7/43,2 (1.80/1.70)
Not SAE std.
54
C rear mounting
Dimensions in millimeters (inches)
This unit accepts a hydraulic pump with
a mounting configuration of the 127-2
(C) size per SAE std. J-744 Oct83. The
output coupling is for a pump shaft of
SAE C size with a 30 involute spline
(per SAE std J-744 Oct83), 14T and
12/24 D.P. (Per ANSI B.92.1a1976).
Concentricity of the shaft of the
attached pump must meet or exceed
requirements of SAE Std. J-744 Oct83.
212,9 (8.38)
181,1
(7.13)
A
To mounting flange face
90,4
(3.56)
13,2
(.52)
.625-11
UNC- 2B thd.
1.45 thru
flange, 2
holes
127,0
(5.00)
60,5
(2.38)
84,1
(3.31)
Snap
ring
AS 568-160
O-ring required
147,6
(5.81)
Pump
model
Dimension A
Dimension L *
35VQTCS
276,9 (10.9)
56,6/54,1 (2.23/2.13)
61,2 (2.41) maximum
45VQTCS
307,3 (12.1)
56,6/54,1 (2.23/2.13)
61,5 (2.42) maximum
Output
coupling
55
Optional Shafts
#203 Straight keyed heavy duty shaft
Dimensions in millimeters (inches)
Note: No. 297 spline shaft
shown on pages 49-51.
A
Key (see chart)
7,9
(.31)
Dimensions
B
9,53 (.375)
12,7 (.500)
12,7 (.500)
25,40 (1.000)
25,35 (.998)
34,90 (1.374)
34,87 (1.373)
38,07 (1.499)
38,05 (1.498)
28,19 (1.110
27,94 (1.100)
38,56 (1.518)
38,30 (1.508)
42,37 (1.668)
42,11 (1.658)
Model
Key
6,35 (.250) sq. x 50,8 (2.00)
7,94 (.313) sq. x 54,0 (2.13)
9,53 (.375) sq. x 57.2 (2.25)
56
Table 2
Single Thru-drive Pumps
and Triple Pumps
Shaft Torque Ratings
Double pumps
Where both cartridges are to be on-load
together, check that the sum of their
separate torques, taken from the graph
below (right), does not exceed the
torque limit in shaft torque Table 1.
Pump
Model
Shaft
No.
Max. Input
Torque
Nm (lb. in.)*
25VQT
203
402 (3560)
A
B
131 (1160)
316 (2800)
25VQT or
2520VQSV10
297
344 (3040)
A
B
131 (1160)
316 (2800)
35VQT
203
659 (5830)
A
B
C
131 (1160)
348 (3080)
437 (3870)
35VQT or
352*VQSV10
297
791 (7000)
A
B
C
131 (1160)
348 (3080)
437 (3870)
45VQT
203
982 (8690)
A
B
C
131 (1160)
384 (3400)
702 (6210)
45VQT or
45*5VQSV10
297
1017 (9000)
A
B
C
131 (1160)
384 (3400)
702 (6210)
Pump
Model
Shaft
Number
Maximum
Input Torque
Nm (lb. in.)
25VQ or
25**VQ
1
86
11
123
203
297
316 (2800)
402 (3560)
316 (2800)
316 (2800)
402 (3560)
344 (3040)
1
11
86
123
203
297
402 (3560)
791 (7000)
659 (5830)
791 (7000)
659 (5830)
791 (7000)
1
11
86
130
203
297
402 (3560)
1017 (9000)
982 (8690)
1017 (9000)
982 (8690)
1017 (9000)
35VQ or
35**VQ
45VQ or
45**VQ
Example:
A 3525VQ38A17 pump operating at 175 bar
(2500 psi) front section and 140 bar (2000 psi)
rear section will require over 452 Nm (4000
lb. in.) input torque. Therefore, all listed shafts
are acceptable except No. 1.
60
50
452
(4000)
42
339
(3000)
38
35
30
25
226
(2000)
21
17
14
12
11
8
5
113
(1000)
35
(500)
70
(1000)
100
(1500)
140
(2000)
175
(2500)
Displacement Code
Table 1
Single & Double Pumps
Shaft Torque Ratings
Max.
Thru-drive
Torque Nm (lb. in.)
Thru-drive
Connection
210
(3000)
57
Model
Series
3525VQT
Displacement Code
(USgpm at 1200 r/min
and 7 bar (100 psi))
Displacement
cm3/rev (in3/rev)
Rated
Speed
r/min
Maximum
Pressure
bar (psi)
Typical Delivery
at Max Speed
and Pressure
l/min (USgpm)
25
81,6 (4.98)
2500
207 (3000)
173,1 (45)
75 (101)
30
97,7 (5.96)
2500
207 (3000)
211,5 (55)
88 (117.5)
35
112,8 (6.88)
2400
207 (3000)
230,8 (60)
98 (132)
38
121,6 (7.42)
2400
207 (3000)
250,0 (65)
104 (140)
12
40,2 (2.45)
2500
207 (3000)
79,0 (21)
38 (51)
14
45,4 (2.77)
2500
207 (3000)
91,0 (24)
43 (58)
17
55,2 (3.37)
2500
207 (3000)
119,2 (31)
51,8 (69,5)
21
Front Pump
Rear Pump
67,5 (4.12)
2500
207 (3000)
146,2 (38)
62 (83)
42
138,7 (8.46)
2200
172 (2500)
255,8 (66.5)
91 (122.5)
50
162,3 (9.90)
2200
172 (2500
303,8 (79)
105 (141)
60
193,4 (11.80)
2200
172 (2500)
369,2 (96)
127 (170)
12
40,2 (2.45)
2200
207 (3000)
68,0 (18)
33 (44)
14
45,4 (2.77)
2200
207 (3000)
79,0 (21)
38 (51)
17
55,2 (3,37)
2200
207 (3000)
100,0 (26.5)
45 (61)
21
67,5 (4.12)
2200
207 (3000)
125,0 (33)
54 (73)
4525VQT
Performance constants: SAE 10W oil @ 82C (180F) and pump inlet @ 0 psig (14.7 psia).
Note: Outlet pressure must always be higher than inlet pressure. See page 6 for details.
Typical Performance
For thru-drive performance, use curves on
the following pages:
Page Number
Model
Series
Shaft-end
Pump
Rear Pump
3525VQT
33
37
4525VQT
34
39
58
Model Codes
1
F3 Viton seals
Omit if not required
Port connections
A SAE 4-bolt flange
AM Metric 4-bolt flange (Flange pads
stamped M for metric threads)
Geometric displacement,
cover end pump
Code = SAE rating (USgpm) at
1200 rpm and 6,9 bar (100 psi)
Pump
Code
cm3/r
series
40
**25VQT 12
45
14
55
17
68
21
10
11
12
13
14
in3/r
2.45
2.77
3.37
4.12
2 Series designation
3525VQT (standard bearing)
3625VQT (3525VQT with heavy
duty bearing)
4525VQT (standard bearing)
Thru-drive coupling
2 With spline for tandem pump
9
in3/r
4.98
5.96
6.88
7.42
8.46
9.90
11.80
Shaft
297 Splined
C size per SAE J744C
32-4 per SAE J744 Oct 83
10
13 Design
Subject to change. Installation
dimensions remain unchanged for
designs 20 through 29.
14 Rotation
(Viewed from shaft end of pump)
L Left hand (counterclockwise)
R Right hand (clockwise)
11 Port position
(Viewed from cover end of pump)
With no. 1 outlet opposite inlet
AA - No. 2 outlet 135 CCW from inlet
AB - No. 2 outlet 45 CCW from inlet
AC - No. 2 outlet 45 CW from inlet
AD - No. 2 outlet 135 CW from inlet
NOTES:
State complete model number when ordering. Example: 3525VQTAS-25A12-2297CC-20R.
Port flange kits with inch screws are available from Vickers and must be ordered separately.
For port flange kits, or mounting, displacement, port, and shaft options other than coded above,
contact your Vickers representative.
59
Installation Dimensions
3525VQT Series
Dimensions in millimeters (inches)
Port connection pads are for use with SAE or
metric 4-bolt flanges. Pads stamped with M for
metric threads. See page 119 for selection of SAE
flanges.
127,00
126.95
(5000
4.998)
12,45 (0.490)
.62511 UNC2B thd.
28,5 (1.125) deep.
4 holes (in. thds.)
15,7 (0.62
M12 thread
20,6 (.812) deep min.
4 holes (metric thds.)
343,8 (13.53)
67,6
(2.66)
109.5
(4.31)
122,2
(4.81)
38,1
(1.50)
55,5
(2.19)
106,2
(4.18)
82,6
(3.25)
45
88,9
(3.50)
17,48
(0.688)
thru2
holes
7,125
(17,48)
74,7
(2.94)
7,87
(0.310)
See rear mounting dimensions
starting on page 62.
147,6
(5.81)
35,05/34,80
(1.380/1.370)
60
Installation Dimensions
4525VQT Series
Dimensions in millimeters (inches)
Port connection pads are for use with SAE or
metric 4-bolt flanges. Pads stamped with M for
metric threads. See page 119 for selection of SAE
flanges.
M12 thread
23,83 (.94) deep. 4
holes (metric thds.)
.500-13 UNC-2B
thd. 23,831 (.938)
deep 4 inch thds
88,90 (3.500)
Inlet port conn.
38,10 (1.500)
Outlet No. 1 port conn.
126,95
127,00
(5.000
4.998)
M16 thread
31,75 (1.25) deep min.
4 holes (metric thds.)
12,45
(0.490)
15,8 (0.62)
.625-11 UNC-2B thd.
31,75 (1.250) deep 4
holes (inch thds.)
25,4 (1.00)
Outlet No. 2
port conn.
External Involute Spline
ANSI B92.1a1976
1.0104 base dia.
1.1667 pitch dia.
Flat Root
Side Fit
14 teeth 12/24 pitch 30pr angle
Major Dia.
Form Dia.
Minor Dia.
Max
1.229 Max
1.082
1.040 Min
1.223 Min
M10 thread
19,05 (.75) deep.
4 holes (metric thds.)
.375-16 UNC-2B thd.
18,0 (.75) deep. 4
holes (inch thds.)
382,4
(15.06)
180,3
(6.31)
135,8
(5.35)
80,1
(3.18)
129,9
(5.11)
42,9 55,8
(1.69) (2.19)
212,5
(8.38)
106,2 (4.18)
93,66
(3.688)
102,39
(4.031)
79,4
(3.12)
79,4
45
(3.12)
17,48
(0.688)
thru. 2
holes
180,98
(7.125)
84,1
74,7 (3.31)
(2.84)
81,0
(3.19)
158,8 (6.25)
162.1 (6.38)
7,87
(0.310)
See rear mounting dimensions
starting on page 62.
147,6
(5.81)
40,51/40,26
(1.595/1.585)
61
A Rear Mounting
(SAE 822 size).
Dimensions in millimeters (inches)
MS28775042
Alternate O ring
32,5/31,0
(1.28/1.22)
Important
dimension.
Must be
observed.
1,45/1,30
(0.057/0.051)
ARP568230
O Ring
82,63/82,58
(3.253/3.251)
47,50
(1.870)
87,53/87,27
(3.446/3.436)
45
6,53/6,38
(0.257/0.251)
106,38
(4.188)
Snap ring
9,19/9,04
(0.362/0.356)
16,26/15,49
(0.640/0610)
343,8 (13.53) to 3525VQT
mounting flange face.
382,4 (15.06) to 4525VQT
mounting flange face.
B Rear Mounting
(SAE 1012 size).
Dimensions in millimeters (inches)
This unit accepts hydraulic pump
with SAE mounting configuration of
1012(B) size per SAE std. J744
Oct 83.
374,3 (14.74)
To mtg. flange face
19,05
(0.750)
45
174,8
(6.88)
148,05
(5.750)
56,6
(2.23)
9,98/9,78
(0.393/0.385)
2,23 (5.8)
Snap ring
Adaptor flange
42,4/39,9
(1.67/1.57)
62
BP Rear Mounting
(SAE B size with spacer for
Vickers PVE19/21 pumps)
Dimensions in millimeters (inches)
133,1
(5.24)
Z
Z
Section ZZ
(typ. 2 plcs.)
101,68
63,5
56,6
101,63 (2.50)
(2.23)
(4.003
4.001)
73,02
(2.875)
45
174,8
(6.88)
10,16/9,91
(0.400/0.390)
3,68/3,56
(0.145/0.140)
16,3 (0.64)
148,05
(5.750)
390,6 (15.38)
To mtg. flange face
Adaptor flange
45,7/43,2 (1.80/1.70)
Not SAE standard
63
No.1 pumping
section (outlet)
No. 2 pumping
section (outlet)
Drive
shaft
Torque (lb.in.)
5000
4000
3000
2000
1000
Torque (Nm)
550
500
450
38 USgpm
35 USgpm
400
30 USgpm
350
300
25 USgpm
250
21 USgpm
200
150
100
50
00 25 50 75 100 125 150 175 200 225
Pressure (bar)
6000
5000
4000
3000
2000
1000
0
Torque (Nm)
Figure 2
Torque (lb.in.)
650
600
60 USgpm
550
57 USgpm
500
50 USgpm
450
47 USgpm
42 USgpm
400
350
300
250
200
150
100
50
0
0 25 50 75 100 125 150 175 200
Pressure (bar)
0
64
Figure 3
Figure 4
**25VQTs Rear Pump
Input Torque Requirement
Torque (lb.in.)
2000
1500
1000
500
0
Torque (Nm)
2500
275
250
225
200
175
150
125
100
75
50
25
0
Model
Max. Torque Nm (lb in)
Series
Input
Thru-drive
3*25VQTA 790 (7000)
131 (1160)
3*25VQTB 790 (7000)
316 (2800)
3*25VQTBP 790 (7000)
316 (2800)
4525VQTA 1017 (9000) 131 (1160)
4525VQTB 1017 (9000) 316 (2800)
4525VQTBP 1017 (9000) 316 (2800)
21 USgpm
19 USgpm
17 USgpm
14 USgpm
12 USgpm
Shaft
Code
11
62
151
11
11
NOTE: Torque limits in Figure 4 must not be exceeded when applying the above
Vickers pumps.
65
Single Pumps
Double Pumps
Versatile
Priority Valve
Flow Control
The flow control cover limits flow to the
operating system to the desired
maximum. Excess flow is diverted to
tank. On double pumps, shaft-end pump
delivery is proportional to speed.
The flow control cover also includes a
relief valve to limit maximum system
pressure.
A typical application of a flow control is
in a power steering unit where it
provides a constant supply of oil over
the engines mid to high speed range.
Reliable
The superior design of these units
makes them last longer ... theyve
proven theyll hold up in rugged
applications such as trenchers,
backhoes and tractors.
Performance
Low vane tip/ring loading allows high
pressure operation. High speeds are
possible because the inlet flow paths are
designed to give uniform oil acceleration
- thus better filling - particularly at low
inlet pressures.
Low Cost
Vickers efficient design produces extra
horsepower per dollar of pump
investment - providing industry with low
pump cost per horsepower capacity.
Hydraulic Balance
Internal inlet and outlet pressure
chambers are diametrically opposed.
66
Delivery USgpm
@ 1200 rpm
7 bar (100 psi)
Displ.
cm3/r
(in3/r)
Max.
r/min
Max.
bar
(psi)
Typical del..
L/min (USgpm)
@ max.
speed &
pressure
Typical input
kW (hp)
@ max.
speed &
pressure
V10
V10F
V10P
1
2
3
4
5
6
7
3,3 (.20)
6,6 (.40)
9,8 (.60)
13,1 (.80)
16,4 (1.00)
19,5 (1.19)
22,8 (1.39)
4800
4500
4000
3400
3200
3000
2800
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
152 (2200)
138 (2000)
13,6 (3.6)
27,7 (7.3)
35,6 (9.4)
41,3 (10.9)
48,5 (12.8)
55,3 (14.6)
60,6 (16)
5,2 (7)
10,1 (13.6)
13,3 (17.8)
15,2 (20.4)
17 (22.8)
18,3 (24.5)
17,9 (24)
V20
V20F
V20P
6
7
8
9
11
12
13
19,5 (1.19)
22,8 (1.39)
26,6 (1.62)
29,7 (1.81)
36,4 (2.22)
39 (2.38)
42,5 (2.59)
3400
3000
2800
2800
2500
2400
2400
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
152 (2200)
152 (2200)
61,0 (16.1)
63,3 (16.7)
67,1 (17.7)
75,0 (19.8)
86,8 (22.9)
87,2 (23)
98,1 (25.9)
21,6 (29)
22 (29.5)
24,2 (32.5)
26,5 (35.5)
28 (37.5)
26,8 (36)
29,1 (39)
Wt.
kg
(lb.)
4,5 - 6,8
(10 - 15)
7,3 - 8,2
(16 - 18)
67
Model Codes
V 20 F - 1 P 13 S - 1 A 8H 22 L
1
Vane pump
Series
10
11
12
9/16-18
St. thd.
(V10P)
3/4-16
St. thd.
(V10P)
P
Mounting
1 2-bolt flange
6 2 bolt flange (SAE B size)
Inlet port connections
V10
series
(V10 only)
3/4 NPT thd. 3/4-16
(V20 only)
St. thd.
(V10F &
V20F)
3/416
St. thd.
(V10 only)
1-1/1612
St. thd.
(V20 only)
3/4-16
St. thd.
(V20F)
1-1/1612
St. thd.
(V20F)
3/4-16
St. thd.
(V10F)
3/4-16
St. thd.
(V10F)
7/8-14
St. thd.
(V20P)
9/16-18
St. thd.
(V10P)
3/4-16
St. thd.
(V20P)
Design
Shaft rotation
(Viewed from shaft end of pump)
L Left hand for counterclockwise.
Omit for right hand.
3/4-16
St. thd.
(V20P)
11
8
Shafts
1 Straight keyed
3 Threaded with woodruff key
11 Splined
12 Splined (V10 only)
38 Splined
62 SAE A Spline (V20 only)
9
V20
series
Pressure
4 L/min (1 USgpm)
8 L/min (2 USgpm)
11 L/min (3 USgpm)
15 L/min (4 USgpm)
23 L/min (6 USgpm)
27 L/min (7 USgpm)
23 L/min (6 USgpm)
27 L/min (7 USgpm)
30 L/min (8 USgpm)
34 L/min (9 USgpm)
42 L/min (11 USgpm)
45 L/min (12 USgpm)
49 L/min (13 USgpm)
Std.
cover
1
2
3
4
6
7
6
7
8
9
11
12
13
Code
10 or 20
3
Integral valves
Orifice No.
Flow rate
2 8 L/min (2 USgpm)
3 11 L/min (3 USgpm)
4 15 L/min (4 USgpm)
5 19 L/min (5 USgpm)
6 23 L/min (6 USgpm)
7 27 L/min (7 USgpm)
8 30 L/min (8 USgpm)
68
Installation Dimensions
V10 Series
Dimensions in millimeters (inches).
Shaft options shown on page 72.
Delivery @
1200 rpm
& 100 psi
1 USgpm
2 USgpm
3 USgpm
4 USgpm
5 USgpm
6 USgpm
7 USgpm
115,6 (4.55)
115,6 (4.55)
115,6 (4.55)
121,9 (4.80)
121,9 (4.80)
127,0 (5.00)
127,0 (5.00)
91,9 (3.62)
91,9 (3.62)
91,9 (3.62)
98,3 (3.87)
98,3 (3.87)
103,4 (4.07)
103,4 (4.07)
12,7 (.50)
Dimensions
82,55/82,50
21,4 (3.250/3.248)
(.843)
.750-16 UNF-2B THD.
(SHOWN)
OR
.500 NPT THD. OUTLET PORT
A
B
24,6 (.97)
76,2 (3.00)
C
38,1 (1.50)
7,9 (.31)
6,35/6,10
(.250/.240)
44,4
(1.75)
4,75 (.187) SQ. KEY
25,4 (1.00) LONG
62,7 (2.47)
19,05/19,02
(.750/.749)
46
(1.81)
SAEA
FLANGE
(REF.)
11,9
(.47) R.
10
21,13/21,00
(.832/.827)
10
38,1 (1.50)
NO. 1 SHAFT
53,2
(2.09)
106,3
(4.19)
11,1
(.44)
2 HOLES
95,2
(3.75)
V10F Series
Dimensions in millimeters (inches).
Shaft options shown on page 72.
Delivery @
1200 rpm
& 100 psi
1 USgpm
2 USgpm
3 USgpm
4 USgpm
5 USgpm
6 USgpm
7 USgpm
128,8 (5.07)
128,8 (5.07)
128,8 (5.07)
135,1 (5.32)
135,1 (5.32)
140,2 (5.52)
140,2 (5.52)
109,5 (4.31)
109,5 (4.31)
109,5 (4.31)
115,8 (4.56)
115,8 (4.56)
120,9 (4.76)
120,9 (4.76)
Dimensions
46,0
(1.81)
TANK PORT
.75016 UN2B THD.
OR .500 NPT THREAD
MAJOR DIA.
18,62/18,47
(.733/.727)
INLET PORT
1.000 NPT THD. OR
1.3212512 UN2B THD.
OR 1.187512 UN2B THD.
B
24,6 (.97)
97,5
(3.84)
B
82,55/82,50
(3.250/3.248)
15,2
(.60)
A
106,9
(4.21)
C
60,7
(2.39)
60,5
(2.38)
12,7 (.50)
31,8
(1.25)
6,35/6,10
(.250/.240)
95,3
(3.75)
21,3
106,4 (.84)
20,6 (4.19)
(.81)
11,9
(.47) R.
10
OUTLET PORT
.750-16 UN-2B THD.
10
SAE A
FLANGE
(REF.)
11,2 (.44)
2 HOLES
69
V10P Series
Dimensions
A
MAJOR DIA.
130,0 (5.12)
130,0 (5.12)
130,0 (5.12)
136,4 (5.37)
136,4 (5.37)
141,5 (5.57)
141,5 (5.57)
109,5 (4.31)
109,5 (4.31)
109,5 (4.31)
115,8 (4.56)
115,8 (4.56)
120,9 (4.76)
120,9 (4.76)
18,62/18,47
(.733/.727)
24,6
(.97)
6,35/6,10
(.250/.240)
60,5
(2.38)
108,0
(4.25)
.437 D.
THRU
2 HOLES
31,8
(1.25)
102,9
(4.05)
CLOCKWISE
ROTATION
12,7 (.50)
COVER POSITION C
50,3
(1.98)
82,55/82,50
(3.250/3.248)
15,2
(.60)
20,6
(.81)
10
D
10
55,6
(2.19)
11,9 (.47) R.
A
30,2 (1.19)
16,0 (.63)
95,3
(3.75)
V20 Series
OUTLET PORT
1.062-12 UN-2B STR. THD.
SAE O-RING
BOSS CONNECTION
NO. 1 SHAFT
Dimensions
A
125,2 (4.93)
131,6 (5.18)
131,6 (5.18)
131,6 (5.18)
136,6 (5.38)
140,2 (5.52)
140,2 (5.52)
102,1 (4.02)
108,4 (4.27)
108,4 (4.27)
108,4 (4.27)
113,5 (4.47)
117,1 (4.61)
117,1 (4.61)
12,7 (.50)
A
55,6
(2.19)
B
31 (1.22)
55,6
(2.19)
66,0
(2.60)
21,13/21,00
(.832/.827)
62,0
(2.44)
B
10
82,55/82,50
(3.250/3.248)
D
55,6
(2.19)
106.4 (4.19)
.004
53,1
(2.09)
19,05/19,02
(.750/.749)
11,1 (.437)
2 HOLES
10
11,9
(.47) R.
47,8 (1.88) R.
70
Installation Dimensions
Dimensions
A
149,6 (5.89)
156,0 (6.14)
156,0 (6.14)
156,0 (6.14)
161,0 (6.34)
164,3 (6.47)
164,3 (6.47)
B
125,7 (4.95)
132,1 (5.20)
132,1 (5.20)
132,1 (5.20)
136,9 (5.39)
140,5 (5.53)
140,5 (5.53)
19,1 (.75)
V20P
SECONDARY OUTLET PORT
.875-14 UNF 2B STR THD
SAE O-RING BOSS
CONNECTION
V20F
TANK PORT
12,7 (.50) NPT
12,7 (.50)
106,48/106,27
(4.192/4.184)
A
C
55,6
(2.19)
B
55,6
(2.19)
31,8 (1.25)
53,1
(2.09)
31,0
(1.22)
23,9 (.940)
62,0
(2.44)
D
10
124,0
(4.88)
82,55/82,50
(3.250/3.248)
62,0
(2.44)
15,7
(.62)
V20P
TANK PORT
.750-16 UNF 2B STR THD
SAE O-RING BOSS
CONNECTION
V20P PRIMARY
OUTLET PORT
.750-16 UNF 2B STR THD
SAE O-RING BOSS
CONNECTION
10
11,9
(.47) R.
4,1 (.16)
15,7
(.62)
11,2
(.44)
2 HOLES
47,8 (1.88)
V20F
OUTLET PORT
.750-16 UNF 2B STR THD
SAE O-RING BOSS
CONNECTION
71
Optional Shafts
V10 Series
Dimensions in millimeters (inches)
Note: No. 1 keyed shaft and No. 38
splined shaft shown on pages 69
and 70 respectively.
50,0
(1.97)
41,9
(1.65)
14,7
(.58)
31,8
(1.25)
3,3 (.13)
30,2 (1.19)
15,88/15,85
(.625/.624)
17,73/17,48
(.698/.688)
.500-20 UNF2A THD.
V20 Series
Dimensions in millimeters (inches)
Note: No. 1 keyed shaft and No. 38
splined shaft shown on pages 70
and 71 respectively. No. 62 splined
shaft same as V10 #11 shaft
shown above.
74,7
(2.94)
70,6
(2.78)
31,8 (1.25)
26,9 (1.06)
16,8
(.66)
50,8
(2.00)
37,3 (1.47)
FULL
DEPTH
OF SPLINE
26,9 (1.06)
31,8 (1.25) HEX
23,83/23,81
(.9380/.9375)
18,62/18,47
(.733/.727)
26,08/25,82
(1.0267/1.0167)
.875-18 #2 THD.
19,07/19,02
(.751/.749)
NOTE:
No. 3 shaft recommended nut
torque 170 Nm (125 lb. ft.)
72
Typical Performance
V10 Single Pumps
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SSU) @ 38C (100F),
inlet pressure zero
1 & 3 GPM RINGS
38 (10)
13,4 (18)
34 (9)
11,9 (16)
10,4 (14)
3 GPM RING
172 BAR (2500 PSI)
69 BAR(1000 PSI)
7 BAR (100 PSI)
8,9 (12)
7,4 (10)
1 GPM RING
172 BAR (2500 PSI)
69 BAR(1000 PSI)
7 BAR (100 PSI)
6,0 (8)
4,5 (6)
3,0 (4)
1,5 (2)
0
3 GPM RING
172 BAR (2500 PSI)
69 BAR(1000 PSI)
7 BAR (100 PSI)
30 (8)
27 (7)
23 (6)
1 GPM RING
172 BAR (2500 PSI)
69 BAR(1000 PSI)
7 BAR (100 PSI)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
800
1600
2400
3200
SPEED r/min
4000
4800
800
1600
2400
3200
SPEED r/min
4000
4800
53 (14)
17,9 (24)
INPUT HORSEPOWER kW (hp)
4 GPM RING
172 BAR (2500 PSI)
14,9 (20)
13,4 (18)
11,9 (16)
6 GPM RING
69 BAR
(1000 PSI)
10,4 (14)
8,9 (12)
7,4 (10)
2 GPM RING
172 BAR (2500 PSI)
4 GPM RING
69 BAR (1000 PSI)
6,0 (8)
45 (12)
16,4 (22)
42 (11)
38 (10)
4 GPM RING
7 BAR (100 PSI)
69 BAR (1000 PSI)
172 BAR (2500 PSI)
34 (9)
30 (8)
27 (7)
23 (6)
19 (5)
15 (4)
2 GPM RING
69 BAR (1000 PSI)
4,5 (6)
7 (2)
1,5 (2)
0
800
1600
2400
3200
SPEED r/min
4000
2 GPM RING
7 BAR (100 PSI)
69 BAR (1000 PSI)
172 BAR (2500 PSI)
11 (3)
3,0 (4)
6 GPM RING
7 BAR
(100 PSI)
69 BAR
(1000 PSI)
152 BAR
(2200 PSI)
49 (13)
6 GPM RING
152 BAR (2200 PSI)
4 (1)
00
4800
800
1600
2400
3200
SPEED r/min
4000
4800
16,4 (22)
49 (13)
14,9 (20)
13,4 (18)
11,9 (16)
7 GPM RING
138 BAR
(2000 PSI)
10,4 (14)
7 GPM RING
69 BAR (1000 PSI)
8,9 (12)
5 GPM RING
69 BAR (1000 PSI)
7,4 (10)
6,0 (8)
45 (12)
42 (11)
38 (10)
34 (9)
30 (8)
5 GPM RING
7 BAR (100 PSI)
69 BAR (1000 PSI)
172 BAR (2500 PSI)
27 (7)
23 (6)
4,5 (6)
19 (5)
3,0 (4)
15 (4)
7 GPM RING 7 BAR (100 PSI)
5 GPM RING 7 BAR (100 PSI)
1,5 (2)
0
7 GPM RING
7 BAR
(100 PSI)
69 BAR
(1000 PSI)
138 BAR
(2000 PSI)
53 (14)
5 GPM RING
172 BAR
(2500 PSI)
17,9 (24)
800
1600
2400
SPEED r/min
3200
11 (3)
8 (2)
800
1600
2400
SPEED r/min
3200
73
7 (100)
70 (1000)
150 (2200)
98 (26)
13
bar (PSI) CODE
91 (24)
83 (22)
83 (22)
76 (20)
76 (20)
68 (18)
11
7 (100)
70 (1000)
175 (2500)
7
61 (16)
61 (16)
53 (14)
45 (12)
38 (10)
53 (14)
45 (12)
38 (10)
30 (8)
30 (8)
23 (6)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
0
800
1200
1600
2000
2400
2800
400
bar (PSI)
150 (2200) 13
26,1 (35)
22,4 (30)
175 (2500)
18,6 (25)
14,9 (20)
70 (1000) 13
11,2 (15)
70 (1000)
7,5 (10)
0
400
7 (100) 13
7 (100) 7
3,7 (5)
800
1200
1600
2000
SPEED r/min
2400
2800
800
CODE
1200
1600
2000
2400
400
7 (100)
70 (1000)
175 (2500)
68 (18)
7 (100)
70 (1000)
175 (2500)
2800
29,8 (40)
175 (2500) 11
175 (2500) 9
26,1 (35)
22,4 (30)
18,6 (25)
14,9 (20)
70 (1000) 11
70 (1000) 9
11,2 (15)
7,5 (10)
3,7 (5)
0
400
7 (100) 11
7 (100) 9
800
1200
1600
2000
2400
2800
SPEED r/min
74
Typical Performance
V20 Single Pumps
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SSU) @ 38C (100F),
inlet pressure zero
98 (26)
7 (100)
70 (1000)
91 (24)
12
150 (2200)
83 (22)
76 (20)
7 (100)
8
70 (1000)
68 (18)
175 (2500)
7 (100)
70 (1000)
175 (2500)
61 (16)
53 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
8 (2)
0
400
800
1200
1600
2000
2400
2800
3200
29,8 (40)
150 (2200) 12
26,1 (35)
22,4 (30)
175 (2500)
175 (2500)
18,6 (25)
14,9 (20)
70 (1000) 12
70 (1000) 8
70 (1000) 6
11,2 (15)
7,5 (10)
7 (100) 12
7 (100)
8
6
7 (100)
3,7 (5)
0
400
800
1200
1600
2000
2400
2800
3200
SPEED - r/min
75
30 (8)
NO. 6 ORIFICE
27 (7)
23 (6)
19 (5)
NO. 3 ORIFICE
15 (4)
11 (3)
8 (2)
NO. 1 ORIFICE
NO. 4 ORIFICE
4 (1)
0
27 (7)
23 (6)
19 (5)
15 (4)
NO. 2 ORIFICE
11 (3)
8 (2)
4 (1)
0
8
(2)
11
(3)
15
(4)
19
(5)
23
(6)
27
(7)
30
(8)
34
(9)
38
(10)
42
(11)
45
(12)
49
(13)
53
(14)
57
(15)
61
(16)
64
(17)
42 (11)
NOTE: 12 & 13 RINGS
ARE RATED AT
150 BAR (2200 PSI)
PRIMARY 7 BAR (100 PSI)
SECONDARY 175 BAR (2500 PSI)
PRIMARY 175 BAR (2500 PSI)
SECONDARY 7 BAR (100 PSI)
38 (10)
34 (9)
NO. 8 ORIFICE
30 (8)
27 (7)
NO. 6 ORIFICE
23 (6)
19 (5)
15 (4)
NO. 4 ORIFICE
11 (3)
8 (2)
NO. 2 ORIFICE
4 (1)
4
(2)
15
(4)
23
(6)
30
(8)
38
(10)
45
(12)
53
(14)
61
(16)
68
(18)
76
(20)
83
(22)
91
(24)
98
(26)
106
(28)
76
Typical Performance
NO. 8 ORIFICE
30 (8)
27 (7)
23 (6)
NO. 4 ORIFICE
NO. 6 ORIFICE
19 (5)
15 (4)
11 (3)
8 (2)
NO. 2 ORIFICE
4 (1)
0
11
(3)
19
(5)
27
(7)
34
(9)
42
(11)
49
(13)
57
(15)
64
(17)
72
(19)
80
(21)
87
(23)
95
(25)
102
(27)
0,14
bar
0,17
0,10
0,07
1.06
1.04
0,28
0,34
bar
psi
1.02
in. Hg
VACUUM
2700 r/min
x .93
2511 r/min
0,21
SPEED RATING
CORRECTION
FACTOR
2
1.0
Example:
Max. speed @ 0 psi inlet
Correction factor @ 5 in. Hg
Max. speed @ 5 in. Hg inlet
0,14
0.98
2
3
4
SUPERCHARGE PRESSURE
0.96
0.94
77
Delivery
USgpm @
1200 r/min
7 bar
(100 psi)
Displ.
cm3/r
(in3/r)
Max.
r/min
Max.
bar
(psi)
Typical del.
L/min
(USgpm)
@ max.
speed &
pressure
Typical
input
kW (hp)
@ max.
speed &
pressure
Weight
kg
(lb)
V2010,
V2010F
&
V2010P
6
7
8
9
11
12
13
19,5 (1.19)
22,8 (1.39)
26,6 (1.62)
29,7 (1.81)
36,4 (2.22)
39,0 (2.38)
42,5 (2.59)
3000
3000
2800
2800
2500
2400
2400
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
152 (2200)
152 (2200)
54,9 (14.5)
63,3 (16.7)
67,1 (17.7)
75,0 (19.8)
86,8 (22,9)
87,2 (23.0)
98,1 (25.9))
18,3 (24.5)
22,0 (29.5)
24,2 (32.5)
26,5 (35.5)
28,0 (37.5)
26,8 (36.0)
29,1 (39.0)
13,6 (30)
V2020,
V2020F
&
V2020P
6
7
8
9
11
12
13
19,5 (1.19)
22,8 (1.39)
26,6 (1.62)
29,7 (1.81)
36,4 (2.22)
39,0 (2.38)
42,5 (2.59)
3000
3000
2800
2800
2500
2400
2400
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
152 (2200)
152 (2200)
54,9 (14.5)
63,3 (16.7)
67,1 (17.7)
75,0 (19,8)
86,8 (22.9)
87,2 (23.0)
98,1 (25.9)
19,4 (26.0)
22,0 (29.5)
24,2 (32.5)
26,5 (35,5)
28,0 (37.5)
26,8 (36.0)
29,1 (39.0)
15,9 (35)
1
2
3
4
5
6
7
3,3 (.20)
6,6 (.40)
9,8 (.60)
13,1 (.80)
16,4 (1.00)
19,5 (1.19)
22,8 (1.39)
3000
3000
3000
3000
3000
3000
2800
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
152 (2200)
138 (2000)
7,6 (2.0)
17,8 (4.7)
26,5 (7.0)
36,0 (9.5)
45,4 (12.0)
55,3 (14.6)
60,6 (16.0)
3,4 (4.5)
6,7 (9.0)
10,0 (13.4)
13,4 (18.0)
16,0 (21.5)
18,3 (24.5)
17,9 (24.0)
13,6 (30)
V2020,
V2020F
&
V2020P
6
7
8
9
11
19,5 (1.19)
22,8 (1.39)
26,5 (1.62)
29,7 (1.81)
36,4 (2.22)
3000
3000
2800
2800
2500
172 (2500)
172 (2500)
172 (2500)
172 (2500)
172 (2500)
54,9 (14.5)
62,5 (16.5)
66,2 (17.5)
75,7 (20.0)
87,1 (23.0)
19,4 (26.0)
22,4 (30.0)
24,2 (32.5)
26,8 (36.0)
28,0 (37.5)
15,9 (35)
78
Model Code
V 2020 F - 1 F 13 S 11 S - 1 CC 8H 30 L
1
2
Series
V2010 or V2020
3
11 - 11 USgpm
12 - 12 USgpm
13 - 13 USgpm
11
11
Position of outlet
(Viewed from cover end of pump)
V2020
Vane pump
6 - 6 USgpm
7 - 7 USgpm
8 - 8 USgpm
9 - 9 USgpm
10
13
14
Integral valves
Orifice No.
Relief valve setting
Flow rate
bar (psi)
l/min (USgpm)
A
B
C
D
E
F
1 4 (1)
2 8 (2)
3 11 (3)
4 15 (4)
6 22 (6)
8 30 (8)
Design
Subject to change. Installation
dimensions remain the same for
designs 10 thru 19 (V2010) and
30 thru 39 (V2020).
13
V2010
With no. 1 outlet opposite inlet
AA No. 2 outlet 135 CCW from inlet
AB No. 2 outlet 45 CCW from inlet
AC No. 2 outlet 45 CW from inlet
AD No. 2 outlet 135 CW from inlet
With no. 1 outlet 90 CCW from inlet
BA No. 2 outlet 135 CCW from inlet
BB No. 2 outlet 45 CCW from inlet
BC No. 2 outlet 45 CW from inlet
BD No. 2 outlet 135 CW from inlet
14
Shaft rotation
(Viewed from shaft end of pump)
L Left hand for counterclockwise
Omit for right hand
Std.
cover
(See table)
10 Shafts
1 Straight keyed
3 Threaded with Woodruff key
11 Splined
12
Pressure
Tank
Secondary
outlet
Tank
9/16-18
St. thd.
(V2010P)
3/4-16
St. thd.
(V2010P)
3/4-16
St. thd.
(V2010 &
V2020F)
3/4-16
St. thd.
(V2020P)
7/8-14
St. thd.
(V2020P)
3/4-16
St. thd.
(V2020F)
1-1/1612
St. thd.
(V2020F)
3/4-16
St. thd.
(V2010F &
V2020F)
3/4-16
St. thd.
(V2010F &
V2020F)
9/16-18
St. thd.
(V2010P)
3/4-16
St. thd.
(V2020P)
79
Installation Dimensions
V2010 Series
Cover end
1, 2 or 3
4 or 5
6 or 7
1, 2 or 3
4 or 5
6 or 7
1, 2 or 3
4 or 5
6 or 7
Dimensions
A
213,1 (8.39)
219,5 (8.64)
224,5 (8.84)
218,2 (8.59)
224,5 (8.84)
229,6 (9.04)
221,7 (8.73)
227,8 (8.97)
232,9 (9.17)
B
189,2 (7.45)
195,6 (7.70)
200,7 (7.90)
194,3 (7.65)
200,7 (7.90)
205,7 (8.10)
197,9 (7.79)
204,0 (8.03)
209,0 (8.23)
C
113,3 (4.46)
113,3 (4.46)
113,3 (4.46)
118,1 (4.65)
118,1 (4.65)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
INLET PORT
38,1 (1.50)
CLOCKWISE
ROTATION
12,7 (.50)
A
C
26,9 (1.06)
76,2
(3.00)
45
VIEW AA
58,7
(2.31)
9,4
(.37)
A
55,6 (2.19)
10
10
14,2
(.56) R.
60,5 (2.38)
55,6
(2.19)
50,8 (2.00)
14,2 (.56)
THRU
2 HOLES
24,54/24,41 (.966/.961)
101,6/101,55
(4.000/3.998)
111,2
(4.38)
22,23/22,20
(.875/.874)
V2010F Series
Dimensions in millimeters (inches). Shaft options shown on page 83.
Rated Delivery, gpm
@ 1200 rpm & 100 psi
Shaft end Cover end
1, 2 or 3
7,8 or 9
4 or 5
7,8 or 9
6 or 7
7,8 or 9
1, 2 or 3
11
4 or 5
11
6 or 7
11
1, 2 or 3
12 or 13
4 or 5
12 or 13
6 or 7
12 or 13
Dimensions
A
226,1 (8.90)
232,4 (9.15)
237,5 (9.35)
230,9 (9.09)
237,2 (9.34)
242,3 (9.54)
234,4 (9.23)
240,8 (9.48)
245,9 (9.68)
B
206,8 (8.14)
213,1 (8.39)
218,2 (8.59)
211,6 (8.33)
217,9 (8.58)
223,0 (8.78)
215,1 (8.47)
221,5 (8.72)
226,6 (8.92)
C
113,3 (4.46)
113,3 (4.46)
113,3 (4.46)
118,1 (4.65)
118,1 (4.65)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
101,6/101,55
(4.000/3.998)
INLET PORT
38,1 (1.50)
TANK PORT
.750-16 UN 2B THD.
OR .500 NPT THD.
9,4 (.37)
12,7 (.50)
A
NO. 2 OUTLET PORT
.750-16 UNF 2B THD.
66,5 (2.62)
B
C
45
26,9 (1.06)
VIEW AA
58,7
(2.31)
CLOCKWISE
ROTATION
121,0 (4.75)
14,2
(.56) R.
76,2
(3.00)
A
51,6 (2.03)
10
B
55,6 (2.19)
10
50,8
(2.00)
97,5 (3.84)
B
VIEW BB
24,54/24,41 (.966/.961)
22,23/22,20 (.875/.874)
146,1
(5.75)
111,3 (4.38)
80
Installation Dimensions
V2010P Series
Dimensions in millimeters (inches). Shaft options shown on page 83.
Rated Delivery, gpm
@ 1200 rpm & 100 psi
Dimensions
INLET PORT CONNECTION PAD IS
FOR USE WITH SAE 4-BOLT FLANGE.
SEE PAGE 119 FOR SELECTION.
Shaft end
Cover end
7,8 or 9
7,8 or 9
7,8 or 9
11
11
11
12 or 13
12 or 13
12 or 13
1, 2 or 3
4 or 5
6 or 7
1, 2 or 3
4 or 5
6 or 7
1, 2 or 3
4 or 5
6 or 7
227,6 (8.96)
249,2 (9.21)
239,0 (9.41)
232,4 (9.15)
238,8 (9.40)
243,8 (9.60)
236,0 (9.29)
242,3 (9.54)
247,4 (9.74)
206,8 (8.14)
213,1 (8.39)
218,2 (8.59)
211,6 (8.33)
217,9 (8.58)
223,0 (8.78)
215,1 (8.47)
221,5 (8.72)
226,6 (8.92)
113,3 (4.46)
113,3 (4.46)
113,3 (4.46)
118,1 (4.65)
118,1 (4.65)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
121,7 (4.79)
SECONDARY OUTLET
PORT .750-16 UNF-2B THD.
101,6/101,55
(4.000/3.998)
INLET PORT
38,1 (1.50)
12,7 (.50)
61,5 (2.42)
22,23/22,20)
(.875/.874)
9,4 (3.70)
111,3 (4.38)
55,6
(2.19)
45
A
52,3 (2.06)
CLOCKWISE
ROTATION
58,7
(2.31)
VIEW
A-A
26,9
(1.06)
66,5 (2.62)
14,2
(.56) R.
10
55,6 (2.19)
76,2
(3.00)
A
17,5 (.69)
B
61,5 (2.42)
10
17,5 (.69)
B
VIEW
B-B
16,0 (.63)
30,2 (1.19)
121,0
(4.75)
146,1
(5.75)
V2020 Series
Dimensions in millimeters (inches). Shaft options shown on page 83.
Rated Delivery, gpm
@ 1200 rpm & 100 psi
Shaft end
7,8 or 9
7,8 or 9
11
11
11
12 or 13
12 or 13
12 or 13
Cover end
6
7, 8 or 9
6
7, 8 or 9
11
6
7, 8 or 9
11
Dimensions
A
213,6 (8.41)
220,0 (8.66)
218,7 (8.61)
225,0 (8.86)
229,9 (9.05)
222,2 (8.75)
228,3 (8.99)
233,4 (9.19)
B
187,7 (7.39)
194,0 (7.64)
192,8 (7.59)
199,1 (7.84)
204,0 (8.03)
196,3 (7.73)
202,4 (7.97)
207,5 (8.17)
INLET PORT
48,8/ 50,8
(1.94/2.00)
C
114,0 (4.49)
114,0 (4.49)
119,1 (4.69)
119,1 (4.69)
119,1 (4.69)
122,4 (4.82)
122,4 (4.82)
122,4 (4.82)
#2 OUTLET PORT
1.062 - 12 UN - 2B THD.
#1 INLET PORT
1.062 - 12UN 2B THD.
50,8 (2.00) R.
12,7 (.50)
A
B
C
26,9
(1.06)
74,7 (2.94)
69,9
(2.75)
14,2 (.56)
THRU
2 HOLES
24,54/24,41
(.966/.961)
10
10
101,6/101,55
(4.000/3.998)
NO. 1 SHAFT EXTENSION
110,5 (4.35)
9,40
(.37)
CLOCKWISE
ROTATION
66,5
(2.62)
55,6 (2.19)
55,6 (2.19)
58,7
(2.31)
146,1
(5.75)
22,23/22,20
(.875/.874)
14,2
(.56) R.
121,0 (4.75)
81
Dimensions
A
235,0 (9.25)
241,3 (9.50)
240,0 (9.45)
246,4 (9.70)
251,2 (9.89)
243,6 (9.59(
249,7 (9.83)
254,8 (10.03)
B
211,1 (8.31)
217,4 (8.56)
216,2 (8.51)
222,5 (8.76)
227,3 (8.95)
219,7 (8.65)
225,8 (8.89)
230,9 (9.09)
C
114,0 (4.49)
114,0 (4.49)
119,1 (4.69)
119,1 (4.69)
119,1 (4.69)
122,4 (4.82)
122,4 (4.82)
122,4 (4.82)
101,6/101,55
(4.000/3.998)
V2020F
OVERFLOW RETURN
1.062-12 UN 2B THD. OR
.750-16 UNF 2B STR. THD.
V2020P
SECONDARY OUTLET PORT
.875 14 UNF 2B STR. THD.
SAE O-RING BOSS CONNECTION
#1 OUTLET PORT
1.062-12 UN 2B THD.
A
58,7
(2.31)
B
55,4
(2.18)
C
26,9 (1.06)
74,7
(2.94)
50,8
(2.00)
CLOCKWISE
ROTATION
12,7 (.50)
73,2
(2.88)
9,4
(.37)
146,1
(5.75)
14,2
(.56) R.
124,0
(4.88)
10
10
V2020P
PRIMARY OUTLET PORT
.750-16 UNF 2B STR. THD.
SAE O-RING BOSS CONNECTION
15,7 (.62)
62,0 (2.44)
14,2 (.56)
THRU
2 HOLES
121,0
(4.75)
15,7 (.62)
V2020P
TANK PORT
.750-16 UNF 2B STR. THD.
SAE O-RING BOSS
CONNECTION
V2020F
#2 OUTLET PORT
.750-16 UNF 2B STR. THD.
SAE O-RING BOSS
CONNECTION
82
Optional Shafts
62,0
(2.44)
50,8
(2.00)
33,3
(1.31)
25,12/24,87
(.989/.979)
4,0 (.16) THRU
22,23/22,20 (.875/.874)
29,2 (1.15)
41,1
(1.62)
33,3
(1.31)
4,0
(.16)
29,2 (1.15)
17,9 (.70)
83
Typical Performance
Shaft-end Pumps
V2010 & V2020 Double Pumps
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SSU) @ 38C (100F),
inlet pressure zero
98 (26)
98 (26)
7 (100)
70 (1000)
150 (2200)
91 (24)
83 (22)
76 (20)
76 (20)
7 (100)
70 (1000)
53 (14)
45 (12)
30 (8)
23 (6)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
2400
400
2800
150 (2200) 12
26,1 (35)
175 (2500) 8
22,4 (30)
18,6 (25)
14,9 (20)
70 (1000) 12
11,2 (15)
70 (1000) 8
7,5 (10)
3,7 (5)
0
400
7 (100) 12
7 (100) 8
800
1200
1600
2000
SPEED r/min
2400
2800
7 (100)
70 (1000)
175 (2500)
800
1200
1600
2000
2400
2800
175 (2500)
45 (12)
30 (8)
2000
11
53 (14)
38 (10)
1600
7 (100)
70 (1000)
175 (2500)
61 (16)
38 (10)
1200
13
7 (100)
70 (1000)
68 (18)
DELIVERY l/min (USgpm)
61 (16)
800
7 (100)
70 (1000)
150 (2200)
175 (2500)
68 (18)
91 (24)
12
83 (22)
400
106 (28)
bar (psi)
29,8 (40)
CODE
150 (2200) 13
175 (2500) 11
175 (2500) 9
175 (2500) 7
26,1 (35)
22,4 (30)
18,6 (25)
70 (1000) 13
70 (1000) 11
70 (1000) 9
70 (1000) 7
14,9 (20)
11,2 (15)
7,5 (10)
7 (100) 13
7 (100) 11
7 (100) 9
7 (100) 7
3,7 (5)
0
400
800
1200
1600
2000
2400
2800
SPEED r/min
84
Typical Performance
1 & 3 GPM RINGS
Cover-end Pumps
10,4 (14)
INPUT HORSEPOWER kW (hp)
8,9 (12)
7,4 (10)
6,0 (8)
4,5 (6)
3,0 (4)
1,5 (2)
0
0
3 GPM RING
7 BAR (100 PSI)
23 (6)
70 BAR (1000 PSI)
175 BAR (2500 PSI)
15 (4)
800
1600
2400
SPEED r/min
3200
53 (14)
45 (12)
38 (10)
16,4 (22)
1 GPM RING
7 BAR (100 PSI)
70 BAR (1000 PSI)
175 BAR (2500 PSI)
8 (2)
0
14,9 (20)
13,4 (18)
11,9 (16)
10,4 (14)
6 GPM RING 70 BAR (1000 PSI)
8,9 (12)
7,4 (10)
4 GPM RING
7 BAR (100 PSI)
70 BAR (1000 PSI)
4,5 (6)
3,0 (4)
30,3 (8)
1,5 (2)
23 (6)
15 (4)
0
2 GPM RING
7 BAR (100 PSI)
70 BAR (1000 PSI)
175 BAR (2500 PSI)
8 (2)
0
3200
30 (8)
1600
2400
SPEED r/min
19,4 (26)
800
800
1600
2400
SPEED r/min
800
17,9 (24)
3200
1600
2400
SPEED r/min
3200
16,4 (22)
5 GPM RING 175 BAR (2500 PSI)
14,9 (20)
INPUT HORSEPOWER kW (hp)
61 (16)
53 (14)
7 GPM RING
7 BAR (100 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
45 (12)
38 (10)
30 (8)
5 GPM RING
7 BAR (100 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
23 (6)
15 (4)
11,9 (16)
10,4 (14)
8,9 (12)
7,4 (10)
5 GPM RING 70 BAR (1000 PSI)
6,0 (8)
4,5 (6)
3,0 (4)
7 GPM RING 7 BAR (100 PSI)
1,5 (2)
8 (2)
0 0
13,4 (18)
800
1600
SPEED r/min
2400
3200
800
1600
SPEED r/min
2400
3200
85
Cover-end pumps
V2020 Double Pumps
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SSU) @ 38C (100F),
inlet pressure zero
98 (26)
7 (100)
70 (1000)
175 (2500)
91 (24)
83 (22)
6 & 8 GPM RINGS
7 (100)
76 (20)
76 (20)
68 (18)
175 (2500)
68 (18)
7 (100)
70 (1000)
175 (2500)
53 (14)
45 (12)
53 (14)
45 (12)
38 (10)
30 (8)
30 (8)
23 (6)
23 (6)
15 (4)
15 (4)
8 (2)
8 (2)
800
1200
1600
2000
SPEED r/min
2400
400
2800 3000
175 (2500) 8
22,4 (30)
175 (2500) 6
18,6 (25)
14,9 (20)
11,2 (15)
70 (1000) 8
70 (1000) 6
7,5 (10)
3,7 (5)
7 (100) 8
7 (100) 6
1200
1600
2000
SPEED r/min
1200
1600
2000
2400
26,1 (35)
800
800
2800 3000
SPEED r/min
29,8 (40)
0
400
61 (16)
38 (10)
400
2400
2800 3000
7 (100)
70 (1000)
175 (2500)
175 (2500)
61 (16)
70 (1000)
11
29,8 (40)
175 (2500) 11
175 (2500) 9
175 (2500) 7
26,1 (35)
22,4 (30)
18,6 (25)
14,9 (20)
70 (1000) 11
70 (1000) 9
70 (1000) 7
7 (100) 11
7 (100) 9
7 (100) 7
11,2 (15)
7,5 (10)
3,7 (5)
0
400
800
1200
1600
2000
2400
2800 3000
SPEED r/min
86
Typical Performance
30 (8)
27 (7)
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
0
27 (7)
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
0
8
(2)
11
(3)
15
(4)
19
(5)
23
(6)
27
(7)
30
(8)
34
(9)
38
(10)
42
(11)
45
(12)
49
(13)
53
(14)
57
(15)
61
(16)
64
(17)
38 (10)
NO. 8 ORIFICE
34 (9)
30 (8)
27 (7)
NO. 6 ORIFICE
23 (6)
19 (5)
15 (4)
NO. 4 ORIFICE
11 (3)
8 (2)
NO. 2 ORIFICE
4 (1)
8
(2)
15
(4)
23
(6)
30
(8)
38
(10)
45
(12)
53
(14)
61
(16)
68
(18)
76
(20)
83
(22)
91
(24)
98
(26)
106
(28)
87
NO. 8 ORIFICE
CONTROLLED FLOW l/min (USgpm)
30 (8)
27 (7)
23 (6)
NO. 4 ORIFICE
NO. 6 ORIFICE
19 (5)
15 (4)
11 (3)
8 (2)
NO. 2 ORIFICE
4 (1)
0
11
(3)
19
(5)
27
(7)
34
(9)
42
(11)
49
(13)
57
(15)
64
(17)
72
(19)
80
(21)
87
(23)
95
(25)
102
(27)
0,07
0,14
bar
0,17
0,10
0,07
1.06
1.04
0,14
0,21
0,28
0,34
bar
SPEED RATING
CORRECTION
FACTOR
1.02
in. Hg
2
1.0
VACUUM
0.98
2
3
4
5
SUPERCHARGE PRESSURE
psi
0.96
0.94
88
High Efficiency
Optimum running clearances and
hydraulic balance provide sustained
high efficiency throughout pump life.
Hydraulic Balance
Vickers design eliminates
pressure-induced bearing loads to
provide longer life and reduced
maintenance.
Integral Valves
Flow control and relief eliminate the
need for separate valves. Vickers
pumps supply, in one package, a
complete power source for steering.
Operating Specifications
Model
Series
VTM42
Delivery USgpm
@ 1200 r/min
7 bar (100 psi)
1
1.5
2
4
5
6
Displ.
cm3/r
(in3/r)
3,4 (.21)
5,1 (.31)
6,2(.38)
12,9 (.79)
15,7 (.96)
19,3 (1.18)
@ 140 bar
(2000 psi)
4250
4000
3800
2800
2300
2000
Maximum
pressure
bar (psi)
Approx.
weight
kg (lbs.)
140
(2000)
6,4
(14)
Model Codes
1
Series
3
Mounting flange
A SAE A mounting flange
(Omit if not required)
10
11
Shaft rotation
Shaft type
15
20
25
30
35
40
45
50
55
60
65
70
75
Reservoir filter
11
Design
Subject to change. Installation
dimensions remain the same for
designs 10 through 19.
Reservoir or manifold
90
Installation Dimensions
VTM42 power steering
pumps with reservoir
78,5
(3.09)
166,1 (6.54)
CL PUMP
174,0 (6.85)
11,2
(.44)
96,8
(3.81)
276,9
(10.90)
20,8
(.82)
70 CU. IN.
RESERVOIR
97,8
(3.85)
214,4
(8.44)
4,76 X 15,9
(.1875 X .625)
WOODRUFF KEY
STANDARD SAE
DIMENSIONS
30,0
(1.18)
28,4 (1.12)
26,9 (1.06)
66,5
(2.62)
14,2
(.56) R.
26,9
(1.06)
PUMP CL
19,02/19,00
(.749/.748)
15,7 (.62)
18,3 (.72)
57,2
(2.25)
76,2
(3.00)
152,4
(6.00)
TANK CL
10,4
(.41)
45
60,5
(2.38)
136,4
(5.37)
22,4 50,8
(.88) (2.00)
RETURN CONNECTION
USE 2,3 (.62) I.D. HOSE
FASTEN WITH HOSE
CLAMPS. MUST BE AIR
TIGHT
1,0
(.04)
12,7 (.50)
57,15/57,10
(2.250/2.248)
7,1 (.28)
35,8 (1.41)
38,1 (1.50)
9,7 (.38)
PRESS CONNECTION
.750 16 UNF 2B THD.
.56 MIN DEEP
USE SAE HYDRAULIC FITTING AND
O-RING FOR .50 O.D. TUBE
108,0
(4.25)
50,8
(2.00)
74,2
(2.92) REF.
22,9
(.90)
.500-20
U.N.F.-2A THD.
106,48/106,22
(4.192/4.182)
130,0
(5.12)
.375-16 U.N.C.-2B TAP THRU
2 PLACES
78,5
(3.09)
PRESS CONNECTION
.750 16 UNF 2B THD.
.56 MIN DEEP
USE SAE HYDRAULIC FITTING AND
O-RING FOR .50 O.D. TUBE
50,8
(2.00)
14,2
(.56) R.
SHIPPING CLOSURE
SHOWN
39,6 (1.56)
10,4
(.41)
19,02/19,00
(.749/.748)
6,88
(2.71)
APPROX.
66,5
(2.62)
45
57,15/57,10
(2.250/2.248)
106,48/106,22
(4.192/4.182)
22,4 50,8
(.88) (2.00)
38,1 (1.50)
60,5
(2.38)
12,7 (.50)
57,2
(2.25)
76,2
(3.00)
1,0
(.04)
.500-20 U.N.F.-2A THD.
7,1 (.28)
35,8 (1.41)
9,7 (.38)
108,0
(4.25)
22,9
(.90)
50,8
(2.00)
74,2
(2.92) REF.
130,0
(5.12)
91
PRESSURE CONNECTION
.75016 UNF-2B THD.
14,2 (.56) MIN. DEEP USE SAE
HYDRAULIC FITTING AND
O RING FOR .500 D. TUBE
110,2
(4.34)
14,2 (.56) R.
82,6/82,5
(3.250/3.248)
NO. 38 SHAFT
INVOLUTE SPLINE
FLAT ROOT SIDE FIT
16/32 DIAMETER FIT
11 TEETH
30 PRESSURE ANGLE
.590 MINOR DIAMETER
MANIFOLD MOUNTING
SURFACE. REFER TO
NEXT PAGE.
28,7
(1.13)
SHIPPING
CLOSURE
SHOWN
31,8
(1.25)
57,2
(2.25)
50,8
(2.00)
42,9
(1.69)
20,6
(.81)
68,8
(2.71)
APPROX.
66,5
(2.62)
106,4
(4.19)
18,62/18,47
(.733/.727)
MAJOR
38,1
(1.50)
12,7 (.50)
31,8
(1.25)
139,7
(5.50)
95,3
(3.75)
4,1 (.16)
11,1
(.437)
THRU
2 HOLES
130,0
(5.12)
92
Installation Dimensions
Manifolds for power
steering pumps
Dimensions in millimeters (inches)
MA MANIFOLD
MD MANIFOLD
50,9/50,7
(2.005/1.995)
16,7/16,4
(.656/.646)
9,7/9,4
(.380/.370)
16,7/16,4
(.656/.646)
31,9/31,6
(1.255/1.245)
9,7/9,4
(.380/.370)
PUMP CL
4,9/4,6
(.192/.182)
8,4/8,2
(.331/.321)
50,9/50,7
(2.005/1.995)
TO MTG. FACE
OF PUMP
8,4/8,2
(.331/.321)
15,7
(.62)
18,3 (.72)
15,7 (.62)
104,6
(4.12)
103,9
(4.09)
TO MTG. FACE
OF PUMP
31,9/31,6
(1.255/1.245)
6,5/6,2
(.255/.245)
41,1
(1.62)
TO CL OF PUMP
4,9/4,6
(.192/.182)
18,3
(.72)
6,4
(.25)
37,3 (1.47) REF.
TO CL OF PUMP
6,4
(.25)
TO C OF PUMP
L
MF MANIFOLD
ME MANIFOLD
.750 NPT
INLET PORT
10,4
(.41)
PUMP CL
41,1
(1.62) 55,9
(2.20)
41,1
(1.62)
THIS TANK BYPASS CONN. IS
REQUIRED FOR INSTALLATIONS
WHICH OPERATE AT PUMP RELIEF
VALVE PRESSURES FOR PERIODS
EXCEEDING 15 SECONDS.
CONNECTION MUST BE MADE
BELOW OIL LEVEL IN RESERVOIR.
.250 NPT
BYPASS PORT
AVAILABLE ONLY
MF MANIFOLD
83,3
(3.28)
55,9
(2.20)
108,7
(4.28)
TO MTG. FACE
OF PUMP
12,7
(.50)
TO CL OF PUMP
TO CL OF PUMP
.750 NPT
INLET PORT
PUMP CL
TO MTG. FACE
OF PUMP
12,7
(.50)
108,7
(4.28)
TO CL OF PUMP
MB MANIFOLD
6,5/6,2
(.255/.245)
9,7/9,4
(.380/.370)
31,9/31,6
(1.255/1.245)
PUMP CL
8,4/8,2
(.331/.321)
10,4
(.41)
6,5/6,2
(.255/.245)
50,9/50,7
(2.005/1.995)
4,9/4,6
16,7/16,4 (.192/.182)
(.656/.646)
A
TO MTG. FACE
OF PUMP
9,4 (.37)
7,9 (.31)
(.25)
104,6
(4.12)
TO CL OF PUMP
96,0
(3.78)
TO CL OF PUMP
Manifold
Code
MA
MB
MD
ME
MF
Dimension A
VTM42
VTM42A
47,0
(1.85)
78,7
(3.10)
75,9
(2.99)
107,7
(4.24)
93
Typical Performance
1 GPM RING
27 (7)
38 (10)
PUMP DELIVERY TOTAL
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
100 BAR
(1500 PSI)
70 BAR
(1000 PSI)
4,50 (6)
3,73 (5)
2,98 (4)
140 (2000)
2,24 (3)
100 (1500)
7 BAR
(100 PSI)
70 (1000)
35 (500)
0
5,22 (7)
1000
1,49 (2)
0,75 (1)
5000
0
6000 7000
SPEED r/min
30 (8)
27 (7)
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
0
34 (9)
MAX. PRESS.
& SPEED
4,50 (6)
70 BAR
1000 PSI)
140 (2000)
2,98 (4)
2,24 (3)
100 (1500)
70 (1000)
1,49 (2)
7 BAR
(100 PSI)
35 (500)
0
0
3,73 (5)
1000
0,75 (1)
0
6000 7000
5000
23 (6)
VTM42(A)
power steering pumps
SPEED r/min
38 (10)
34 (9)
34 (9)
30 (8)
27 (7)
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
0
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
70 BAR
(1000 PSI)
5,22 (7)
4,50 (6)
MAX. PRESS.
& SPEED
140 (2000)
3,73 (5)
2,98 (4)
100 (1500)
2,24 (3)
70 (1000)
7 BAR
(100 PSI)
35 (500)
0
1000
1,49 (2)
0,75 (1)
5000
0
6000 7000
10,44 (14)
9,69 (13)
8,95 (12)
8,20 (11)
7,46 (10)
70 BAR (1000 PSI)
6,71 (9)
5,97 (8)
5,22 (7)
4,50 (6)
5,97 (8)
7,46 (10)
6,71 (9)
100 BAR
(1500 PSI)
PRESSURE bar (psi)
27 (7)
4 (1)
8,20 (11)
30 (8)
140 (2000)
3,73 (5)
2,98 (4)
100 (1500)
2,24 (3)
70 (1000)
1,49 (2)
35 (500)
0,75 (1)
1000
2000
3000
4000
5000
6000
4 GPM RING
2 GPM RING
38 (10)
0
7000
SPEED r/min
94
Typical Performance
VTM42(A)
Power Steering Pumps
6 GPM RING
38 (10)
5 GPM RING
DELIVERY L/min (USgpm)
34 (9)
30 (8)
PUMP DELIVERY TOTAL
27 (7)
23 (6)
19 (5)
15 (4)
11 (3)
8 (2)
4 (1)
27 (7)
23 (6)
19 (5)
28,4 L/min (7.5 USgpm) ORIFICE
24,6 L/min (6.5 USgpm) ORIFICE
20,8 L/min (5.5 USgpm) ORIFICE
17,0 L/min (4.5 USgpm) ORIFICE
15 (4)
11 (3)
8 (2)
4 (1)
0
0
140 BAR (2000 PSI)
7,46 (10)
6,71 (9)
5,97 (8)
5,22 (7)
4,50 (6)
MAX. PRESS.
& SPEED
3,73 (5)
140 (2000)
2,98 (4)
100 (1500)
2,24 (3)
7 BAR
(100 PSI)
70 (1000)
1,49 (2)
0,75 (1)
35 (500)
0
1000
2000
3000
4000
SPEED r/min
5000
0
6000
8,95 (12)
8,20 (11)
7,46 (10)
6,71 (9)
5,97 (8)
5,22 (7)
4,50 (6)
8,95 (12)
8,20 (11)
10,44 (14)
9,69 (13)
9,69 (13)
11,20 (15)
MAX. PRESS.
& SPEED
3,73 (5)
2,98 (4)
140 (2000)
2,24 (3)
100 (1500)
7 BAR
(100 PSI)
70 (1000)
1,49 (2)
0,75 (1)
35 (500)
0
38 (10)
PUMP
34 (9) DELIVERY
TOTAL
30 (8)
1000
2000
3000
4000
0
5000
SPEED r/min
95
Characteristics
Hydraulic Balance
Smooth Operation
Efficiency
Optimum running clearances and
hydraulic balance assure sustained high
efficiency over the life of the motor.
Operating Specifications
Model
series
M2U
M2210
Torque
Nm/6,9 bar
(lb. in./100 psi)
2,0 (18)
2,8 (25)
4,0 (35)
2,8 (25)
4,0 (35)
Displ.
cm3/r
(in3/r)
21,6 (1.32)
25,4 (1.55)
37,5 (2.29)
24,7 (1.51)
35,4 (2.16)
Maximum torque
Nm (lb. in.) @
max. pressure
38,4 (340)
46,3 (410)
67,8 (600)
46,3 (410)
56,5 (500)
Maximum speeds
& pressures
2800 r/min @ 138 bar (2000 psi)
2500 r/min @ 138 bar (2000 psi)
2000 r/min @ 138 bar (2000 psi)
2200 r/min @ 138 bar (2000 psi)
1800 r/min @ 121 bar (1750 psi)
Approx.
weight
lbs.
7,7
(17)
9,5
(21)
Model Codes
M 2 U - 1 S 35 S - 1 C 10 L
1
Vane motor
Series
Uni-directional rotation
10
11
9
Outlet position
(Viewing cover end)
Outlet port
S 1-5/16 12 st. thd.
Mounting
1 2-bolt flange
5
Design
Subject to change. Installation
dimensions remain the same for
designs 10 through 19.
10
Shaft type
1 Straight keyed
3 Threaded
11 Splined
Inlet port
11
Rotation
L Left hand (counterclockwise)
Omit for right hand (clockwise)
M 2 - 2 1 0 - 35 - 1 C - 13
1
Vane motor
7
4
1
3
6
11
Shaft type
Straight keyed
Threaded
Straight keyed (stub)
Splined
8
Cover position
(Viewing cover end)
97
Installation Dimensions
M2U series
Dimensions in millimeters (inches)
Shaft options shown on page 99.
OUTLET PORT
1.3125-12 UN-2B THD.
FOR SAE HYDRAULIC FITTING
USED WITH 1 O.D. TUBING
Dimensions
A
B
Model
#1 SHAFT
INLET PORT
1.3125-12 UN-2B THD.
FOR SAE HYDRAULIC FITTING
USED WITH 1 O.D. TUBING
12,7 (.50)
A
52,3
(2.06)
52,3
(2.06)
C
62,0
(2.44) 53,8
(2.12)
CLOCKWISE
ROTATION
11,1 (.438)
2 HOLES
67,6
(2.66)
4,1 (.16)
41,1
(1.62)
34
(1.34)
4,8 (.1875)
KEY
21,13/21,00
(.832/.827)
124,0
(4.88)
19,05/19,02
(.750/.749)
82,55/82,50
(3.250/3.248)
82,55/82,50
(3.250/3.248)
47,8 (1.88) R.
130,0 (5.12)
M2-200 series
Dimensions in millimeters (inches)
Shaft options shown on page 99.
CONNECTION K
3/4 NPT
CONNECTION L
3/4 NPT
12,7 (.50)
106,4
(4.19)
53,1
(2.09)
71,8
(2.81)
4,1 (.16)
67,6
(2.66)
149,9
(5.90)
37,3
(1.47)
41,1
(1.62)
106,4
(4.19)
B
21,13/21,00
(.832/.827)
122,9
53,1 (4.84)
(2.09)
#1 SHAFT
4,788/4,7625
(.1885/.1875)
KEY
95,3
(3.75)
50,8 (2.00)
DRAIN CONNECTION
3/8 PIPE THD
106,27/106,47
(4.184/4.192)
82,55/82,50
(3.250/3.248)
19,05/19,02
(.750/.749)
32,5 (1.28)
A
CLOCKWISE
ROTATION
53,1
(2.09)
130,0
(5.12)
98
Optional Shafts
26,9 (1.06)
74,7
(2.94)
50,8
(2.00)
31,8 (1.25)
#13 WOODRUFF KEY
16,8
(.66)
37,3
(1.47)
9,7 (.38)
FULL DEPTH
OF SPLINE
INVOLUTE SPLINE
16/32 D.P.
FLAT ROOT 11 TEETH
30 PRESSURE ANGLE
6,4 (.25)
26,9
(1.06)
26,08/25,82
(1.0267/1.0167)
23,83/23,81
(.751/.749)
18,62/18,47
.875-18 #2 THD.
(.9380/.9375)
(.733/.727)
NOTE:
Nut torque 169,5 Nm (125 lb. ft.)
M2-200 series
Dimensions in millimeters (inches)
Note: No. 1 keyed shaft is shown
on page 98.
31,8
(1.25)
12,7
(.50)
#9 WOODRUFF KEY
21,25/21,00
(.8368/.8268)
19,01/19,00
(.7485/.7480)
6,4 (.25)
18,3 (.72)
99
Typical Performance
M2U Series
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SUS) @ 38C (100F)
68 (18)
61 (16)
Volume required L/min (USgpm)
76 (20)
68 (18)
52 (14)
Volume required L/min (USgpm)
61 (16)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
8 (2)
52 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
400
8 (2)
11,9 (16)
8,9 (12)
6,0 (8)
3,0 (4)
0
0
400
56,5 (500)
45,2 (400)
33,9 (300)
22,6 (200)
11,3 (100)
0
400
400
Power kW (hp)
0
45,2 (400)
33,9 (300)
22,6 (200)
11,3 (100)
0
Power kW (hp)
14,9 (20)
138 bar (2000 psi)
11,9 (16)
8,9 (12)
6,0 (8)
3,0 (4)
0
400
800
100
Typical Performance
M2U Series
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SUS) @ 38C (100F)
83 (22)
76 (20)
68 (18)
61 (16)
52 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
8 (2)
400
800
1200
1600
2000
Speed r/min
67,8 (600)
56,5 (500)
103 bar (1500 psi)
45,2 (400)
33,9 (300)
22,6 (200)
34 bar (500 psi)
11,3 (100)
0
Power kW (hp)
400
800
1200
Speed r/min
1600
2000
14,9 (20)
11,9 (16)
8,9 (12)
6,0 (8)
3,0 (4)
0
0
400
800
1200
Speed r/min
1600
2000
101
M2-200 Series
Performance Constants:
Oil temp. 49C (120F), viscosity
32 cSt (150 SUS) @ 38C (100F)
61 (16)
52 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
8 (2)
0
0
400
800
1200 1600
Speed r/min
2000 2200
76 (20)
Volume required L/min (USgpm)
61 (16)
52 (14)
45 (12)
38 (10)
30 (8)
23 (6)
15 (4)
8 (2)
0
400
800
1200
Speed r/min
1600
45,2 (400)
33,9 (300)
22,6 (200)
11,3 (100)
0
400
800
1200
1600
Speed r/min
2000 2200
56,5 (500)
56,5 (500)
45,2 (400)
33,9 (300)
22,6 (200)
11,9 (16)
400
800
1200
Speed r/min
1600
6,0 (8)
3,0 (4)
400
800
1200
1600
Speed r/min
2000 2200
Power kW (hp)
8,9 (12)
11,3 (100)
0
Power kW (hp)
68 (18)
11,9 (16)
8,9 (12)
6,0 (8)
3,0 (4)
400
800
1200
Speed r/min
1600
102
Reliable
Series Operation
Efficient
Vickers exclusive dual-alternate
pressure plate design provides overall
efficiency of about 86%.
Reversibility
Through the dual plate design, the
motors may be reversed simply by
reversing the direction of oil flow. See
note below table on page 104 regarding
pressure/rotation of model series 50M.
Replaceable Cartridge
Replaceable cartridges permit motor
overhauls in just 10 minutes - in the
field! A cartridge can be replaced without
removing the unit from the vehicle, and
usually without disconnecting hydraulic
lines.
103
Operating Specifications
Torque
Model Nm/6,9 bar
Series (lb.in./100 psi)
25M
35M
45M
50M
Displacement
cm3/r (in3/r)
Flow Input
@ 1200 r/min
L/min (USgpm)
Max. Torque
Nm (lb.in.) @
Max. Pressure
4,7 (42)
6,2 (55)
7,3 (65)
43,9 (2.68)
57,7 (3.52)
68,7 (4.19)
52,7 (13.9)
69,4 (18.3)
82,6 (21.8)
115,8 (1025)
151,4 (1340)
180,8 (1600)
9,0 (80)
10,7 (95)
13,0 (115)
83,6 (5.10)
100,3 (6.12)
121,9 (7.44)
100,4 (26.5)
120,5 (31.8)
146,3 (38.6)
221,5 (1960)
264,4 (2340)
320,9 (2840)
14,7 (130)
17,5 (155)
20,9 (185)
138,0 (8.42)
163,2 (9.96)
193,2 (11.79)
165,6 (43.7)
195,9 (51.7)
232,3 (61.3)
361,6 (3200)
429,4 (3800)
502,9 (4450)
24,9 (220)
28,8 (255)
33,9 (300)
231,3 (14.11)
268,2 (16.36)
317,2 (19.35)
277,8 (73.3)
322,2 (85.0)
380,7 (100.5)
615,9 (5450)
717,6 (6350)
844,1 (7470)
Maximum
Speeds & Pressure
Approx.
Weight
kg (lb)
18 (40)
73 (160)
Model Codes
25 M 65 A - 11 C - 20 - ***
1
Series
25M
35M
45M
50M
26M
36M
46M
51M
2
Standard
bearing
Heavy duty
bearing
Vane motor
Shaft
1 Straight keyed
11 Splined
7
Design
Subject to change. Installation
dimensions remain the same for
designs 20 through 29.
114
124
6 Cover position
(Viewing cover end)
104
Installation Dimensions
25M Motors
Dimensions in millimeters (inches)
Shaft options shown on page 107.
Port connection pads are for use
with SAE 4-bolt flanges. See page
119 for selection.
#11 SHAFT
SAE INVOLUTE SPLINE DATA
FLAT ROOTMAJOR DIA FIT
16/32 DIAMETRAL PITCH
13 TEETH 30
PRESSURE ANGLE
.749 T.I.F. DIA
.8125 PITCH DIA
CONNECTION L
31.75 (1.25) PORT
CONNECTION K
31.75 (1.25) PORT
12,7 .50)
101,60/101,55
(4.000/3.998)
CLOCKWISE ROTATION
9,65/9,14
(.380/.360)
182,4 (7.18)
144,3 (5.68)
39,6 (1.56)
58,7 (2.31)
76,2
(3.00)
174,8 (6.88)
44,5 (1.75)
33,3 (1.31)
1,5
(.06)
13,5
(.53)
120,7
(4.75)
146,1 (5.75)
134,9
(5.31)
27,8 (1.09)
14,2 (.56) THRU
2 HOLES
35M Motors
CONNECTION L
38,1 (1.5) PORT
69,9 (2.75)
88,9
(3.50)
127,00/126,95
(5.000/4.998)
#11 SHAFT
SAE INVOLUTE SPLINE DATA
FLAT ROOTMAJOR DIA FIT
12/24 DIAMETRAL PITCH
14 TEETH 30
PRESSURE ANGLE
1.082 T.I.F. DIA
1.1667 PITCH DIA
15,7 (.62)
139,7
(5.50)
211,1 (8.31)
170,7 (6.72)
48,3 (1.90)
12,7/12,2
(.500/.480)
CLOCKWISE ROTATION
62,0 (2.44)
47,6 (1.875)
1,5
(.06)
9,7
(.38)
8.38
5.81
DIA.
181,1
(7.13)
158,8
(6.25)
35,1 (1.38)
17,5 (.688)
THRU 2 HOLES
31,70/31,67 (1.248/1.247) MAJOR
26,42
(1.040) MIN MINOR
105
45M Motors
CONNECTION K
#11 SHAFT
SAE INVOLUTE SPLINE DATA
FLAT ROOT MAJOR DIA FIT
12/24 DIAMETRAL PITCH
14 TEETH
30 PRESSURE ANGLE
1.0822 T.I.F. DIA
1.1667 PITCH DIA
CONNECTION L
50,8 (2.00) PORT
127,00/126,95
(5.000/4.998)
12,7/12,2
(.500/.480)
249,2 (9.81)
158,8 (6.25)
79.2
(3.12)
C
1,5
(.06)
93,5
(3.68)
212,9 (8.38)
62,0 (2.44)
197,9 (7.79)
52,8 (2.08)
CLOCKWISE ROTATION
147,6 (5.81)
47,8 (1.88)
9,7
(.38)
181,1
(7.13)
39,6
(1.56)
173,0
(6.81)
50M Motors
152,40/152,35
(6.000/5.998)
101,6
(4.00)
22,4 (.88)
12,7/12,2
(.500/.480)
294,9 (11.61)
196,9
(7.75)
C
231,9 (9.13)
98,6
(3.88)
74,4
(2.93)
#11 SHAFT
SAE INVOLUTE
SPLINE DATA
FLAT ROOT
SIDE DIA FIT
8/16 DIAMETRAL PITCH
13 TEETH
30 PRESSURE ANGLE
1.501 T.I.F. DIA
1.6250 PITCH DIA
CLOCKWISE ROTATION
200,2
(7.88)
69,9 (2.75)
120,7
(4.75)
26,42 (1.040)
MIN MINOR
266,7
(10.50)
66,8
(2.63)
6,35
(.25)
228,6
(9.00)
47,5
(1.87)
219,7
(8.65)
A
1,5
(.06)
REF
36,6 (1.44)
20,6 (.81)
THRU
2 HOLES
43,71/43,56
(1.721/1.715) MAJOR
106
Optional Shafts
25M series
58,7
(2.31)
47,8
(1.88)
1,5
(.06)
REF
31,8
(1.25)
4,75 (.187)
KEY
28,4
(1.12)
24,46/24,31
(.963/.957)
27,8
(1.093)
22,23/22,20
(.875/.874)
35,1
(1.38)
47,8
(1.88)
35,18/34,93
(1.250/1.248)
1,5 (.06)
REF
62,0
(2.44)
50M series
No. 1 straight keyed shaft
Dimensions in millimeters (inches)
11,10 (.437) KEY
50,8
(2.00)
49,38/49,12
(1.944/1.934)
47,5
(1.87)
44,45/44,42
(1.750/1.749)
66,8
(2.63)
1,5 (.06)
REF
74,4
(2.93)
107
Typical Performance
42 LB. IN. MODEL
25M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
265 (70)
227 (60)
175 BAR (2500 PSI)
140 BAR (2000 PSI)
70 BAR (1000 PSI)
35 BAR (500 PSI)
189 (50)
151 (40)
265 (70)
227 (60)
114 (30)
189 (50)
76 (20)
151 (40)
38 (10)
114 (30)
76 (20)
38 (10)
0
TORQUE
113,0 (1000)
175 BAR
(2500 PSI)
90,4 (800)
140 BAR
(2000 PSI)
67,8 (600)
22,6 (200)
29,8 (40)
22,4 (30)
14,9 (20)
45,2 (400)
37,3 (50)
Power kW (hp)
Torque Nm (lb.in)
135,6 (1200)
7,5 (10)
800
1600
2400
3200
0
4000
SPEED r/min
265 (70)
227 (60)
189 (50)
265 (70)
151 (40)
227 (60)
114 (30)
189 (50)
76 (20)
151 (40)
175 BAR (2500 PSI)
140 BAR (2000 PSI)
70 BAR (1000 PSI)
35 BAR (500 PSI)
38 (10)
0
114 (30)
76 (20)
38 (10)
0
52,2 (70)
Torque Nm (lb.in)
135,6 (1200)
175 BAR
(2500 PSI)
113,0 (1000)
140 BAR
(2000 PSI)
90,4 (800)
44,7 (60)
37,3 (50)
29,8 (40)
22,4 (30)
67,8 (600)
45,2 (400)
70 BAR
(1000 PSI)
22,6 (200)
35 BAR
(500 PSI)
0
0
800
1600
2400
3200
14,9 (20)
Power kW (hp)
TORQUE
158,2 (1400)
7,5 (10)
0
4000
SPEED r/min
108
Typical Performance
25M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
303 (80)
265 (70)
151 (40)
227 (60)
114 (30)
189 (50)
175 BAR
(2500 PSI)
140 BAR
(2000 PSI)
70 BAR
(1000 PSI)
35 BAR
(500 PSI)
76 (20)
38 (10)
0
151 (40)
114 (30)
76 (20)
38 (10)
0
TORQUE
(1600)
175 BAR
52,2 (70)
(2500 PSI)
135,6 (1200)
140 BAR
(2000 PSI)
113,0 (1000)
90,4 (800)
70 BAR
(1000 PSI)
67,8 (600)
35 BAR
(500 PSI)
45,2 (400)
22,6 (200)
44,7 (60)
37,3 (50)
29,8 (40)
22,4 (30)
14,9 (20)
Power kW (hp)
Torque Nm (lb.in.)
158,2 (1400)
7,5 (10)
0
0
800
1600
2400
3200
0
4000
SPEED r/min
109
35M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
379 (100)
303 (80)
227 (60)
379 (100)
151 (40)
303 (80)
76 (20)
227 (60)
151 (40)
226,0 (2000)
180,8 (1600)
135,6 (1200)
TORQUE
74,6 (100)
59,7 (80)
140 BAR
(2000 PSI)
140 BAR (2000 PSI)
44,7 (60)
29,8 (40)
90,4 (800)
70 BAR
(1000 PSI)
45,2 (400)
0
0
76 (20)
800
1600
2400
SPEED r/min
35 BAR
(500 PSI)
3200
Power kW (hp)
Torque Nm (lb.in)
14,9 (20)
0
4000
379 (100)
303 (80)
454 (120)
227 (60)
379 (100)
151 (40)
303 (80)
76 (20)
227 (60)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
151 (40)
76 (20)
0
TORQUE
89,5 (120)
226,0 (2000)
74,6 (100)
180,8 (1600)
59,7 (80)
140 BAR
(2000 PSI)
135,6 (1200)
90,4 (800)
70 BAR
(1000 PSI)
35 BAR
(500 PSI)
45,2 (400)
0
800
1600
2400
3200
44,7 (60)
29,8 (40)
14,9 (20)
Power kW (hp)
Torque Nm (lb.in)
271,2 (2400)
0
4000
SPEED r/min
110
Typical Performance
35M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
454 (120)
379 (100)
530 (140)
303 (80)
454 (120)
227 (60)
379 (100)
151 (40)
303 (80)
227 (60)
76 (20)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
151 (40)
76 (20)
0
TORQUE
316,4 (2800)
104,4 (140)
89,5 (120)
271,2 (2400)
74,6 (100)
226,0 (2000)
180,8 (1600)
59,7 (80)
44,7 (60)
135,6 (1200)
70 BAR
(1000 PSI)
90,4 (800)
35 BAR
(500 PSI)
29,8 (40)
Power kW (hp)
Torque Nm (lb.in)
14,9 (20)
45,2 (400)
0
0
800
1600
2400
3200
4000
SPEED r/min
111
45M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
530 (140)
568 (150)
454 (120)
530 (140)
416 (110)
492 (130)
379 (100)
454 (120)
341 (90)
416 (110)
303 (80)
379 (100)
265 (70)
341 (90)
227 (60)
303 (80)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI) 265 (70)
175 BAR (2500 PSI)
492 (130)
189 (50)
151 (40)
227 (60)
114 (30)
189 (50)
76 (20)
151 (40)
38 (10)
114 (30)
76 (20)
119,3 (160)
38 (10)
Torque Nm (lb.in)
339,0 (3000)
271,2 (2400)
203,4 (1800)
Power kW (hp)
104,4 (140)
89,5 (120)
TORQUE
74,6 (100)
138 BAR
(2000 PSI)
59,7 (80)
69 BAR (1000 PSI)
44,7 (60)
135,6 (1200)
29,8 (40)
67,8 (600)
14,9 (20)
800
1600
2400
SPEED RPM
3200
4000
112
Typical Performance
45M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
155 LB. IN. MODEL
681 (180)
644 (170)
606 (160)
681 (180)
568 (150)
644 (170)
530 (140)
606 (160)
492 (130)
568 (150)
530 (140)
416 (110)
492 (130)
379 (100)
454 (120)
341 (90)
416 (110)
303 (80)
379 (100)
35 BAR (500 PSI)
70 BAR (1000 PSI) 341 (90)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
303 (80)
454 (120)
265 (70)
227 (60)
189 (50)
265 (70)
151 (40)
227 (60)
114 (30)
189 (50)
76 (20)
151 (40)
38 (10)
114 (30)
76 (20)
134,2 (180)
38 (10)
119,3 (160)
474,5 (4200)
104,4 (140)
406,7 (3600)
89,5 (120)
339,0 (3000)
271,2 (2400)
203,4 (1800)
Power kW (hp)
Torque Nm (lb.in)
TORQUE
138 BAR
(2000 PSI)
74,6 (100)
59,7 (80)
69 BAR
(1000 PSI)
44,7 (60)
135,6 (1200)
29,8 (40)
67,8 (600)
14,9 (20)
34 BAR
(500 PSI)
800
1600
2400
SPEED r/min
3200
4000
113
45M Motors
185 LB. IN. MODEL
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
795 (210)
757 (200)
719 (190)
795 (210)
681 (180)
757 (200)
644 (170)
719 (190)
606 (160)
681 (180)
568 (150)
644 (170)
530 (140)
606 (160)
492 (130)
568 (150)
454 (120)
530 (140)
416 (110)
492 (130)
454 (120)
379 (100)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
341 (90)
303 (80)
379 (100)
265 (70)
341 (90)
227 (60)
303 (80)
189 (50)
265 (70)
151 (40)
227 (60)
114 (30)
189 (50)
76 (20)
151 (40)
38 (10)
114 (30)
76 (20)
164,0 (220)
38 (10)
149,1 (200)
134,2 (180)
119,3 (160)
Torque Nm (lb.in)
474,5 (4200)
406,7 (3600)
339,0 (3000)
Power kW (hp)
542,3 (4800)
104,4 (140)
138 BAR
(2000 PSI)
89,5 (120)
74,6 (100)
271,2 (2400)
59,7 (80)
203,4 (1800)
44,7 (60)
135,6 (1200)
29,8 (40)
67,8 (600)
14,9 (20)
416 (110)
0
0
69 BAR
(1000 PSI)
34 BAR (500 PSI)
800
1600
2400
3200
4000
SPEED r/min
114
Typical Performance
50M Motors
220 LB. IN. MODEL
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
833 (220)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
757 (200)
681 (180)
833 (220)
606 (160)
757 (200)
530 (140)
681 (180)
454 (120)
606 (160)
379 (100)
530 (140)
303 (80)
454 (120)
227 (60)
151 (40)
379 (100)
303 (80)
76 (20)
227 (60)
151 (40)
76 (20)
757 (200)
909 (240)
681 (180)
833 (220)
606 (160)
757 (200)
530 (140)
681 (180)
454 (120)
606 (160)
379 (100)
530 (140)
303 (80)
454 (120)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI)
175 BAR (2500 PSI)
227 (60)
151 (40)
677,9 (6000)
Torque Nm (lb.in)
833 (220)
179,0 (240)
TORQUE
564,9 (5000)
149,1 (200)
119,3 (160)
140 BAR
(2000 PSI)
70 BAR 89,5 (120)
(1000 PSI)
451,9 (4000)
339,0 (3000)
226,0 (2000)
35 BAR
(500 PSI)
29,8 (40)
113,0 (1000)
0
59,7 (80)
Power kW (hp)
909 (240)
0
0
800
1600
2400
3200
SPEED r/min
379 (100)
303 (80)
76 (20)
227 (60)
151 (40)
76 (20)
677,9 (6000)
Torque Nm (lb.in)
TORQUE
179,0 (240)
564,9 (5000)
149,1 (200)
451,9 (4000)
140 BAR
(2000 PSI) 119,3 (160)
70 BAR
89,5 (120)
(1000 PSI)
339,0 (3000)
226,0 (2000)
59,7 (80)
35 BAR
(500 PSI)
29,8 (40)
113,0 (1000)
0
0
800
1600
SPEED r/min
2400
3200
Power kW (hp)
790,9 (7000)
115
50M Motors
Performance Constants:
Oil SAE 10W,
viscosity 32 cSt (150 SUS)
@ 38C (100F)
300 LB. IN. MODEL
1060 (280)
984 (260)
909 (240)
1060 (280)
833 (220)
984 (260)
757 (200)
909 (240)
681 (180)
833 (220)
606 (160)
757 (200)
530 (140)
681 (180)
454 (120)
606 (160)
379 (100)
530 (140)
303 (80)
454 (120)
35 BAR (500 PSI)
70 BAR (1000 PSI)
140 BAR (2000 PSI) 379 (100)
175 BAR (2500 PSI)
227 (60)
151 (40)
303 (80)
76 (20)
227 (60)
151 (40)
76 (20)
790,9 (7000)
Torque Nm (lb.in)
TORQUE
208,8 (280)
677,9 (6000)
179,0 (240)
564,9 (5000)
149,1 (200)
140 BAR
(2000 PSI)
119,3 (160)
70 BAR
(1000 PSI)
451,9 (4000)
89,5 (120)
339,0 (3000)
35 BAR
(500 PSI)
226,0 (2000)
59,7 (80)
29,8 (40)
113,0 (1000)
0
Power kW (hp)
903,9 (8000)
800
1600
2400
3200
SPEED r/min
116
Foot Mounts
Foot bracket kits can be used to mount
pumps or motors having standard SAE-J
744 2-bolt A, B, or C mounting flanges.
These designations correspond to -A-,
R UNC-2B THREAD
(4 PLACES)
J
BOLT CIRCLE
0,05 (002)
4HOLES
FOR MOUNTING
H
E
K
D
C
Model
number
Dimensions mm (in.)
D
E
FBA10
134,9
(5.31)
69,9
(2.75)
152,4
(6.00)
76,2
(3.00)
FBB10
180,8
(7.12)
92,2
(3.63)
171,5
(6.75)
FBC10
215,9
(8.50)
109,5
(4.31)
265,2
(10.44)
Model
number
127,0
(5.00)
36,6
(1.44)
63,5
(2.50)
12,7
(.50)
85,8
(3.38)
146,0
(5.75)
36,6
(1.44)
73,2
(2.88)
12,7
(.50)
132,6
(5.22)
235,0
(9.25)
50,8
(2.00)
117,6
(4.63)
15,7
(.62)
Dimensions mm (in.)
M
N
P
FBA10
106,4
(4.19)
96,0
(3.78)
15,0
(.59)
50,8
(2.00)
12,7
(.50)
82,6
(3.25)
17,5
(.69)
.38-16
11,2
(.44)
FBB10
146,0
(5.75)
95,8
(3.77)
15,0
(.59)
50,8
(2.00)
12,7
(.50)
101,6
(4.00)
17,3
(.68)
.50-13
17,3
(.68)
FBC10
181,1
(7.13)
131,6
(5.18)
19,1
(.75)
76,2
(3.00)
17,3
(.68)
127,0
(5.00)
19,1
(.75)
.62-11
17,3
(.68)
117
Filler/Breather Unit
SP-113-C
Dimensions in millimeters (inches)
General Usage:
As a filler cap and air filter for hydraulic
reservoirs.
Provides protected air vent opening, dirt
screen and air filter.
Cover attached to neck of filter by
means of a safety chain. Prevents cap
being lost or misplaced.
Pressure Drop VS. Oil Flow
Into/Out of Reservoir
Pressure Drop (Inches Hg)
L/min
(USgpm)
57 (15)
76 (20)
91 (24)
102 (27)
.25
.50
.75
1.00
10 MICROMETRE (NOMINAL)
AIR FILTER ELEMENT INSIDE CAP
5,5 (.218) 6 HOLES
(EQUALLY SPACED)
76,2
(3.00)
82,5
(3.25)
47,8
(1.88)
65,0
(2.56)
73,2
(2.88)
GASKET
30 MESH GALVANIZED
STEEL WIRE SCREEN
118
Threaded Connection
Dimensions in millimeters (inches)
C SCREW THD.
E
D
J DIA.
SURFACE MUST BE
FLAT AND SMOOTH
H
B
A SAE
STRAIGHT THD.
Model
Assembly
A
SAE Straight
Thread
FL1-6-12S-10
683829
1.0625-12
(3/4 tube)
52,3
(2.06)
3/8-16
65,0
(2.56)
23,9
(.94)
47,8
(1.88)
11,2
(.44)
22,4
(.88)
19,0
(.75)
13,5
(.53)
31,8
(1.25)
FL1-8-16S-10
683830
1.3125-12
(1 tube)
58,7
(2.31)
3/8-16
69,8
26,2
52,4
(2.75) (1.03) (2.06)
13,1
(.52)
26,2
25,4
(1.03) (1.00)
16,8
(.66)
35.0
(1.38)
FL1-10-20S-10
683831
1.625-12
(1-1/4 tube)
73,1
79,2
29,4
58,7
7/16-14
(2.88)
(3.12) (1.16) (2.31)
15,1
(.59)
30,2
31,8
(1.19) (1.25)
21,3
(.84)
38,1
(1.50)
FL1-12-24S-10
683832
1.875-12
(1-1/2 tube)
82,6
(3.25)
17,8
(.70)
35,7
38,1
(1.41) (1.50)
18,5
(.73)
41,1
(1.62)
1/2-13
93,7
35,0
69,8
(3.69) (1.38) (2.75)
119
Oil Recommendations
The oil in a hydraulic system serves as
the power transmission medium. It is
also the systems lubricant and coolant.
Selection of the proper oil is a
requirement for satisfactory system
performance and life.
The following recommendations will
assist in the selection of suitable oils for
use with Vickers products. Vickers does
not publish a recommended oil list by
brand name or supplier due to the
extremely wide variety of oil types on the
market.
In most cases, use of these
recommendations will lead to selection
of a suitable oil. However, due to the
complex nature of oil formulation, the
variety of oils available and peculiarities
of individual hydraulic applications, there
will be rare instances where oil selected
on the basis of these recommendations
will yield unsatisfactory results. Vickers
cannot be responsible for such
exceptions. In this respect, the customer
is encouraged to consult his Vickers
representative when selecting an oil.
SAE Viscosity
Designation
23C to 54C
(10F to 130F)
5W, 5W-20,
5W-30
18C to 83C
(0F to 180F)
10W
18C to 99C
(0F to 210F)
10W-30, 10W-40
10C to 99C
(14F to 210F)
20-20W
ISO Viscosity
Grade
21C to 60C
(5F to 140F)
22
15C to 77C
(5F to 170F)
32
9C to 88C
(15F to 190F)
46
1C to 99C
(30F to 210F)
68
Crankcase Oil
120
Special Requirements
When special considerations indicate a
need to depart from recommended oils
or operating conditions, consult your
Vickers representative.
Horsepower:
Horsepower =
GPM x PSI
1714
Torque:
Torque (lb. in.) =
HP x 63025
RPM
Volumetric Efficiency:
Volumetric efficiency (pump) =
OUTPUT GPM
X 100
THEORETICAL GPM
THEORETICAL GPM
X 100
INPUT GPM
Overall Efficiency:
Overall efficiency =
OUTPUT HP
X 100
INPUT HP
Flow:
Flow (gpm) =
Conversion Factors:
1 hp = 33,000 ft. lbs. per minute
1 hp = 42.4 btu per minute
1 hp = 0.746 kWhr (kilowatt hour)
1 U.S. gallon = 231 cubic inches
Pipe volume varies as the square of the
diameter; volume in gallons = 0.0034 D2L
where: D = inside diameter of pipe in inches
L = length in inches
Velocity in feet per second = 0.408 x flow (gpm)
D2
where: D = inside diameter of pipe in inches.
Atmospheric pressure at sea level = 14.7 psi.
Atmospheric pressure decreases approximately 0.41 psi
for each 1,000 feet of elevation to o 23,000 feet.
Pressure (psi) = feet head x 0.433 x specific gravity.
Specific gravity of oil is approximately 0.85.
Thermal expansion of oil is about 1 cu. in. per 1 gallon per
10F rise in temperature.
121
100
20000
90
80
BASED ON FORMULA
70
AREA (SQ. IN.) =
GPM. X 0.3208
VELOCITY (FT./SEC.)
60
50
10000
9000
40
8000
7000
4 1/2
30
4 1/2
4
20
15
6000
3 1/2
3 1/2
5000
3
20
4000
2 1/2
2 1/2
10
9
8
7
6
5
4
15
2
3000
1 3/4
1 1/2
1 1/2
10
2
2
1 1/4
2000
1 1/4
8
1
7
6
3/4
1000
1/2
4
5/8
.4
MAXIMUM
RECOMMENDED VELOCITY
FOR
INTAKE LINES
.3
9/16
800
700
.5
3/4
900
7/8
1
.9
.8
.7
.6
3/8
1/2
.2
6
7/16
600
3/8
1/4
500
5/16
2
1/8
400
1/4
.1
.09
.08
.07
.06
8
9
10
.05
.04
.03
.01
.009
.008
.007
.006
.005
.004
MAXIMUM
RECOMMENDED VELOCITY
FOR
PRESSURE LINES
20
30
40
50
.4
1/8
.5
100
.75
200
15
AREA OF PIPE, TUBE AND HOSE SQ. IN.
.02
1
FLOW GALLONS PER MINUTE
300
122