Professional Documents
Culture Documents
C90 Disassembly Procedure
C90 Disassembly Procedure
2
Disassembly Procedure
Please follow the information provided in this section to perform the complete disassembly procedure of the notebook. Be sure to use proper tools described before.
Chapter
he C90 Notebook consists of various modules. This chapter describes the procedures for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your service needs.
The disassembly procedure consists of the following steps: Battery Module CPU Module Memory Module HDD Module Optical Drive Module WLAN Module GPU Module Fan Set Motherboard Module Keyboard Module Top Case Module LCD Module
2-1
Disassembly procedure
B A T T E R Y
Battery Module
The illustration below shows how to remove the battery module. Remove Battery module
1Slide the battery latch and pull the battery out of the system.
C P U
M O D U L E
CPU Module
The illustrations below show how to remove the CPU module from the notebook. Removing CPU module
R E M O V A L
1. Remove 4 screws on bottom case and remove the bottom case cover.
2-2
Disassembly procedure
2. Remove 4 screws and then take the CPU heat sink away.
3. Press the CPU latch slightly to move it out of the hook then turn over the bracket.
2-3
Disassembly procedure
M E M O R Y M O D U L E M E M O R Y R E M O V A L
Memory Module
The illustration shows how to remove the memory module form the notebook. Removing Memory module
1. Pull two latches here to pop the Memory module up at 45 angles, and then pull out the module at that angle.
2-4
Disassembly procedure
H D D M O D U L E H D D M O D U L E R E M O V A L
HDD Module
The illustrations below show how to remove the HDD module from the notebook. Removing HDD Module
1. Unscrew and remove 2 screws here and pull the hard disk module toward the direction of the arrow and then lift it up and take it out.
2-5
Disassembly procedure
O P T I C A L D R I V E R E M O V A L
W L A N M O D U L E
WLAN Module
The illustrations below show how to remove the WLAN module from the notebook. Remove WLAN module
W L A N M O D U L E R E M O V A L
1. Disconnect the two antennas here and then remove 2 screws on WLAN module to pop it up at 30 degree angles and then pull it out at that angle.
2-6
Disassembly procedure
G P U
M O D U L E
GPU Module
The illustrations below show how to remove the GPU module from the notebook. Removing GPU module
R E M O V A L
2. Remove 2 screws on GPU board to pop it up at 30 degree angles and then pull it out at that angle.
3. Remove 4 screws on the bracket here and then separate it from VGA board.
2-7
Disassembly procedure
4. Remove 3 screws on North bridge Heat Sink module and then take it away.
F A N
M O D U L E
FAN Module
The illustrations below show how to remove the FAN module from the notebook. Removing FAN module
R E M O V A L
2-8
Disassembly procedure
2-9
Disassembly procedure
M O T H E R B O A R D O T H E R B O A R D R E M O V A L
Motherboard
The illustrations below show how to disassemble and remove the Motherboard.
Removing Motherboard
3. Remove 1 screw here on the right hinge slot and then disconnect 2 cables here.
2 - 10
Disassembly procedure
2 - 11
Disassembly procedure
6. Separate the Top case from the bottom case, *before that remember to remove SD dummy card and E-express dummy card from the system.
8. Remove 2 screws from IO Bar and then take the TV-IN board away.
2 - 12
Disassembly procedure
9. Remove 2 screws on Power Extend board and then remove the board.
2 - 13
Disassembly procedure
1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1). 2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers. 3. Lock the connector (no. 3) again to avoid possible breakage.
3.
3.
13. Remove mother board from top case.*Lift the edge of bottom case slightly while removing the mother board module.
2 - 14
Disassembly procedure
15. Remove 2 screws on MODEM and then remove it from mother board.
16. Disconnect TPM module from mother board and then take it away.
2 - 15
Disassembly procedure
17. Remove 7 screws here on bottom case and then remove it.
K E Y B O A R D
Keyboard Module
The illustration of below shows how to remove the keyboard Removing Keyboard
2 - 16
Disassembly procedure
T O P
C A S E
R E M O V A L
1. Remove 2 screws on USB board and then take the board away.
2. Remove 1 piece of tape here and then disconnect Touch pad FPC from Touch pad board.
2 - 17
Disassembly procedure
3. Remove 4 screws on Finger board bracket and then remove the bracket.
4. Remove 2 screws on Finger print board, and then separate it from the bracket.
5. Remove 2 screws on each speaker and then remove them from top case.
2 - 18
Disassembly procedure
L C D
M O D U L E
LCD Module
The illustrations below show how to remove and disassemble the LCD module.The module contains LCD panel, Inverter board, LCD bezel, LCD back cover.
L C D
M O D U L E
I S A S S E M B L Y
1. Remove 6 rubber pads and 2 rubber bars here and then remove 6 screws on LCD front bezel.
2. Pry the inside edges softly to separate LCD front bezel from LCD panel and take it away.
2 - 19
Disassembly procedure
4. Disconnect inverter cable and LCD cable from inverter board and take away the inverter board.
5. Remove 2 screws here and then take away the LCD TFT.
2 - 20
Disassembly procedure
6. Remove 4 screws on each LCD bracket and take both brackets away.
7. Remove 2 pieces of tape here and disconnect Coaxial cable from LCD TFT, and then remove the coaxial cable.
2 - 21
Disassembly procedure
10. Remove the plastic bracket here and then move out the camera from its compartment.
2 - 22
Disassembly procedure
11Unfix 8 pieces of tape here and then take microphone out of the slot.
12. Remove the camera module and microphone module from LCD back cover.
13. Unfix 3 pieces of tape here and then remove the white antenna from LCD back cover.
2 - 23
Disassembly procedure
14. Unfix 3 pieces of tape here and then remove the black and grey antennas from LCD back cover.
2 - 24