Professional Documents
Culture Documents
SERVICE MANUAL
COLOR TELEVISION
20AF46 20AF46C
The above model is classified as a green product (*1), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*2). For (*1) and (*2), see the next page.
DOCUMENT CREATED IN JAPAN, January, 2006 GREEN
(*1)
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts. Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also be used as replacement parts.
(*2)
LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
A1-1
20AF46/20AF46C
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
IMPORTANT
When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section of the heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)
A1-2
20AF46/20AF46C
TABLE OF CONTENTS
GREEN PRODUCT PROCUREMENT ........................................................................................ LEAD-FREE SOLDER ................................................................................................................ SERVICING NOTICES ON CHECKING ..................................................................................... HOW TO ORDER PARTS .......................................................................................................... IMPORTANT ............................................................................................................................... TABLE OF CONTENTS .............................................................................................................. GENERAL SPECIFICATIONS ................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ............................................................................................... 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................ SERVICE MODE LIST ................................................................................................................ CONFIRMATION OF HOURS USED ......................................................................................... WHEN REPLACING EEPROM (MEMORY) IC .......................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................. BLOCK DIAGRAM ...................................................................................................................... PRINTED CIRCUIT BOARDS MAIN/CRT ................................................................................................................................ SCHEMATIC DIAGRAMS MICON ..................................................................................................................................... CHROMA ................................................................................................................................. DEFLECTION .......................................................................................................................... POWER ................................................................................................................................... SOUND .................................................................................................................................... TUNER/STEREO ..................................................................................................................... COMB FILTER/AV ................................................................................................................... CRT .......................................................................................................................................... WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... ELECTRICAL REPLACEMENT PARTS LIST ........................................................................... A1-1 A1-1 A1-2 A1-2 A1-2 A2-1 A3-1~A3-10 B1-1 B2-1, B2-2 C-1 C-1 C-2 D-1~D-5 E-1, E-2 F-1~F-4 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 H-1, H-2 I-1, I-2 J1-1, J1-2 J2-1~J2-8
A2-1
20AF46/20AF46C
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 20 inch / 508mmV Flat +0.45G/0.18G NTSC 2 Speaker Front Side 2 x 4.7 Inch 8 ohm 2.5+2.5 W W No US System M 1Tuner USA(W/ Cable) 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation X-Radiation Operation Storage 105 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes Yes No UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
G-2
Tuning System
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Protector
G-4
Regulation
G-5 G-6
A3-1
20AF46
GENERAL SPECIFICATIONS
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Sound Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/Cable Auto CH Memory Add/ Delete Option Language CH Label Favorite CH V-Chip Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes English
French
Spanish
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
A3-2
20AF46
GENERAL SPECIFICATIONS
G-10 Remote Control Unit Glow in Dark Remocon Format Remocon Format Custom Code Power Source Total Keys Keys RC-GQ Yes Toshiba Toshiba TV:40-BF h 3V UM-4 x 2 pcs 30 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No No No No No No No No No No No
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down Cap/Text(TV/Caption/Text) 1/2(CH1/CH2) TV/Video(TV/AV) CH RTN(Quick View) Sleep RECall(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE DVD MENU < DVD MENU > DVD CLEAR TOP MENU DVD MENU
A3-3
20AF46
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Auto Shut Off Canal+ Cable Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Station List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) PTB Sheet ESP Card 300 ohm to 75 ohm Antenna Adapter Yes Yes No Yes No No Yes Yes Yes USA,Toshiba Type No No No Yes No Yes No No No Yes 2 Lines Yes No Yes Yes Yes Yes Yes Yes No Yes Yes Yes English/Spanish Yes Yes No
G-12
Accessories
A3-4
20AF46
GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/Cable Selector Degauss Main Power SW Power Stand-by On Timer Video Input = VIDEO2 Audio Input = VIDEO2 Other Terminal Video Input(Rear1) = VIDEO1 Video Input(Rear2) = VIDEO2 Audio Input(Rear1) = VIDEO1 Audio Input(Rear2) = VIDEO2 Video Output Audio Output Euro Scart Color Stream S Input Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Material Dimensions W x D x H(mm) Description of Origin Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2(L/MONO,R) Head Phone RCA No RCA x 2(L/MONO,R) No No No No RCA x 3 Yes No No No F Type No 590 x 484 x 446.5 23 kg ( 50.6 lbs) 26.5 kg ( 58.3 lbs) No ---Sets -/--- x -- x -No Double/Brown 695 x 575 x 549 Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 60 (ORION SPEC:46) 272 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes Green procurement of TOSHIBA Phase3(Phase3A)
Rear
Indicator
Terminals
Front
Rear
Gift Box
Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Environmental standard requirement Pb-free
G-17
Cabinet Material
G-18
Environment
A3-5
20AF46
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Magnetic Field BV/BH 20 inch / 508mmV Flat +0.45G/0.18G NTSC 2 Speaker Front Side 2 x 4.7 Inch 8 ohm 2.5+2.5 W W No US System M 1Tuner USA(W/ Cable) 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Circuit IC Protector(Micro Fuse) Safety Radiation X-Radiation Operation Storage 105 W at AC 120 V 60 Hz 3 W at AC 120 V 60 Hz -kWh/Year Yes Yes No CSA IC HWC +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
G-2
Tuning System
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Protector
G-4
Regulation
G-5 G-6
A3-6
20AF46C
GENERAL SPECIFICATIONS
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Sound Bass Treble Balance BBE On/Off Stable Sound On/Off Surround On/Off Set Up TV/Cable Auto CH Memory Add/ Delete Option Language CH Label Favorite CH V-Chip Lock On/Off Timer Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating 16: 9 G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer / Off Timer / Clock) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes No Yes English French Spanish
On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode)
A3-7
20AF46C
GENERAL SPECIFICATIONS
G-10 Remote Control Unit Glow in Dark Remocon Format Remocon Format Custom Code Power Source Total Keys Keys RC-GQ Yes Toshiba Toshiba TV:40-BF h 3V UM-4 x 2 pcs 30 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No No No No No No No No No No No
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down Cap/Text(TV/Caption/Text) 1/2(CH1/CH2) TV/Video(TV/AV) CH RTN(Quick View) Sleep RECall(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down 16: 9 CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) FF Rew Rec Play Stop TV VCR Cable DVD CODE DVD MENU < DVD MENU > DVD CLEAR TOP MENU DVD MENU
A3-8
20AF46C
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Auto Shut Off Canal+ Cable Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Energy Star Favorite CH Surround 16:9 Mode Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Station List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) PTB Sheet ESP Card 300 ohm to 75 ohm Antenna Adapter Yes Yes No Yes No No Yes Yes No Type No No No Yes No Yes No No No Yes 2 Lines Yes No Yes Yes Yes Yes Yes Yes No Yes Yes Yes English / French Yes Yes No
G-12
Accessories
No No No No No No No No No No No No Yes UM-4 x 2 No No No No No No No
A3-9
20AF46C
GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/Cable Selector Degauss Main Power SW Power Stand-by On Timer Video Input = VIDEO2 Audio Input = VIDEO2 Other Terminal Video Input(Rear1) = VIDEO1 Video Input(Rear2) = VIDEO2 Audio Input(Rear1) = VIDEO1 Audio Input(Rear2) = VIDEO2 Video Output Audio Output Euro Scart Color Stream S Input Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Material Dimensions W x D x H(mm) Description of Origin Yes No No No Yes Yes Yes Yes No No No No Yes(RED) No No RCA RCA x 2(L/MONO,R) Head Phone RCA No RCA x 2(L/MONO,R) No No No No RCA x 3 Yes No No No F Type No 590 x 484 x 446.5 23 kg ( 50.6 lbs) 26.5 kg ( 58.3 lbs) No ---Sets -/--- x -- x -No Double/Brown 695 x 575 x 549 Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 60 (ORION SPEC:46) 272 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes Green procurement of TOSHIBA Phase3(Phase3A)
Rear
Indicator
Terminals
Front
Rear
Gift Box
Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Environmental standard requirement Pb-free
G-17
Cabinet Material
G-18
Environment
A3-10
20AF46C
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. B1-1 20AF46/20AF46C
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not rotate or move the IC back and forth , until IC can move back and forth easily after desoldering the leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
20AF46/20AF46C
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, always be sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
FIG. 1
C-1
20AF46/20AF46C
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 1 second. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC.
C-2
20AF46/20AF46C
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION Use an isolation transformer when performing any service on this chassis. Before removing the anode cap, discharge electricity because it contains high voltage. When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.)
2. BASIC ADJUSTMENTS
2-1: CONSTANT VOLTAGE 1. Set condition is AV MODE without signal. 2. Connect the digital voltmeter to the TP003. 3. Adjust the VR502 until the digital voltmeter is 115 0.5V. 2-2: CUT OFF 1. Place the set with Aging Test for more than 15 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select CUT OFF. 5. Adjust the Screen Volume until a dim raster is obtained. 2-3: WHITE BALANCE, WHITE BALANCE CS NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the gray scale pattern from the Pattern Generator with Brust On. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (12) on the remote control to select R. BIAS. 5. Press the CH. UP/DOWN button on the remote control to select the R. BIAS, G. BIAS, B. BIAS, B. DRIVE or R. DRIVE. 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, B. DRIVE and R. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 8. Press the TV/VIDEO button on the remote control to set to the CS mode. 9. Receive the gray scale pattern from the Pattern Generat or with Brust On. 10. If the picture is too much green.Activate the adjustment mode display of Fig. 1-1 and press the channel button (28) on the remote control to select CB PED. 11. Adjust the VOL. UP/DOWN button on the remote control to select the step up. 12. If the picture is too much red.Activate the adjustment mode display of Fig. 1-1 and press the channel button (29) on the remote control to select CR PED. 13. Adjust the VOL. UP/DOWN button on the remote control to select the step down. 2-4: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct.
Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Multi-sound Generator 4. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1.
TV
00 OSD
29 Fig. 1-1
2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 FUNCTION OSD H CUT OFF H. VCO H. PHASE AFC GAIN V. SHIFT H. SIZE V. SIZE V. LINERITY VS CORRECTION R DRIVE B DRIVE R CUT OFF G CUT OFF B CUT OFF BRIGHT MAX BRIGHT CENT BRIGHT MIN NO. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 FUNCTION CONTRAST MAX CONTRAST CENT CONTRAST MIN COLOR MAX COLOR CENTER COLOR MIN TINT SHARPNESS CB DL CR DL CB PED CR PED PARABOLA CORNER TRAPWZIUM LEVEL SEPARATION1 SEPARATION2
ELECTRICAL ADJUSTMENTS
2-5: VERTICAL POSITION 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. 2-6: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select V. SIZE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 9 2%. 2-7: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-6. After the adjustment of Vertical Linearity, reconfirm the Vertical Position and Vertical Size adjustments. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness, contrast, to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (08) on the remote control to select V. LINEARITY. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-8: LEVEL 1. Connect the AC voltmeter to pin 6 of CP101. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select LEVEL. 3. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 90 2mV. 2-9: HORIZONTAL PHASE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select H.PHASE. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-10: CONTRAST MAX 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select CONT. MAX. 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes 95. 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 5. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 1~3. D-2 00 OSD A 29 B 2-11: SEPARATION 1, 2 Please do the method (1) or method (2) adjustment. Method (1) 1. Set the multi-sound signal generator for each different L-ch and R-ch frequency (Ex. L-ch=2KHz, R-ch=400Hz) and receive the RF. 2. Connect the oscilloscope to the pin 6 and pin 7 of CP101. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 4. Press the VOL. UP/DOWN button on the remote control to adjust it until the audio output wave becomes a fine sine wave. 5. Press the CH UP button once the set to SEP 2 mode. Then perform the above adjustment 4. Method (2) 1. Set the multi-sound signal generator L-ch=1KHz, R-ch =Non input and receive the RF. 2. Connect the oscilloscope to the pin 6 of CP101. 3. Press the AUDIO SELECT button on the remote control to set to the stereo mode. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (34) on the remote control to select SEP 1. 5. Press the VOL. UP/DOWN button on the remote control to adjust it until the R-ch output becomes minimum. 6. Set the multi-sound signal generator L-ch=Non input, R-ch=1KHz and receive the RF. 7. Connect the oscilloscope to the pin 7 of CP101. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select SEP 2. 9. Press the VOL. UP/DOWN button on the remote control to adjust it until the L-ch output becomes minimum. The output difference of the between with Filter and without Filter should be more than 25db for both L and R. 2-12: OSD POSITION 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-1)
TV
Fig. 2-1
20AF46/20AF46C
ELECTRICAL ADJUSTMENTS
2-13: BRIGHT CENT 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 10% is starting to be visible. 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the TV/VIDEO button on the remote control to set to the CS mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI CENT". 9. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "80". 2-14: COLOR CENT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP022. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "COL. CENT". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 120 5% of the white level. (Refer to Fig. 2-2) 7. Receive the video color bar pattern. (Audio Video Input) 8. Set to the AV mode. Then perform the above adjustments 2~6. 9. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 2~4. 10.Press the VOL. UP/DOWN button on the remote control until the color step No. becomes "66". 2-15: TINT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP024. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (24) on the remote control to select "TINT". 5. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line. (Refer to Fig. 2-3) 6. Receive the video color bar pattern. (Audio Video Input) 7. Set to the AV mode. Then perform the above adjustments 2~5. 8. Press the TV/VIDEO button on the remote control to set to the CS mode. Then perform the above adjustments 2~4. 9. Press the VOL. UP/DOWN button on the remote control until the tint step No. becomes "52".
Fig. 2-3 2-16: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. NO. 02 04 05 06 09 15 17 19 20 21 23 25 26 27 30 31 32 FUNCTION H.VCO AFC GAIN V.SHIFT H.SIZE VS CORRECTION BRI.MAX BRI.MIN CONT.CENT CONT.MIN COL.MAX COL.MIN SHARPNESS CB DL CR DL PARABOLA CORNER TRAPEZIUM RF 03 07 02 01 34 125 75 50 18 90 00 40 00 00 31 31 31 AV 03 07 02 01 34 125 75 50 18 90 00 40 00 00 31 31 31 CS 03 07 02 01 34 125 75 50 18 90 00 40 00 00 31 31 31
120%
white 100%
Fig. 2-2
D-3
20AF46/20AF46C
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar genera2. tor. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends 3. are equally wide. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen 4. is green. 5. Confirm red and blue color. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B
WEDGE
WEDGE
D-4
20AF46/20AF46C
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT CD803
CRT PCB
CP803 TP024 TP022 J801 CP806 R805 R803
CP801B
CP802B
VR401
W003 VR502
CRT CP502 CP802A SPEAKER CP501 CP1001 J705 J706 J707 J1001 CD1001
MAIN PCB
AC IN
CD501
D-5
20AF46/20AF46C
BLOCK DIAGRAM
COMB FILTER IC IC1501 TC90A45FG 13 C OUT 15 Y OUT Y IN 3 AMP Q603, Q614, Q605 VIDEO SW(Y) IC IC1502 MM1501XNRE S-JACK J702 LINE1(REAR) J701 6 3 2 3 4 6 Vin1 V.OUT 4 Vin2 2
CHROMA IC IC601 M61283BFP FB401 VIDEO LINE OUT Q802, Q806 B OUT 16 51 VIDEO SW(C) IC IC1503 MM1501XNRE 6 Vin1 V.OUT 4 Vin2 46 42 CVBS1 CVBS2 H OUT 8 2 49 Y IN(Y/C) G OUT 15 R OUT 14 C IN(Y/C) V OUT 63 Q402 H.DRIVER Q405 H.OUT MICON IC101 OEC7090B R IN 23 G IN 22 B IN 21 FAST BLK 24 X602 3.97545MHz 26 SOUND DECORDER IC IC902 AN5829S-E1V 14 24 5 SDA 6 SCL SPEAKER SP1001 MEMORY IC IC199 BR24L16FJ-WE2 4 10 3 30 16 19 6 8 2 12 7 2 3 5 SOUND AMP IC1001 AN7522N 1 HEADPHONE_JACK J1001 SPEAKER SP1002 SDA XTAL 3.58 34 27 SCL 34 RED R 35 GREEN G 36 BLUE B 33 BLANK 30 SCL1 31 SDA1 X.OUT 20 KEY1 6 KEY2 7 VOL UP CH UP REMOCON 9 ON_TIMER 10 X.IN 19 X101 8MHz BLUE OUT Q803, Q805 GREEN/RED OUT Q801, Q804 RED/GREEN OUT 6 8 V-OUT IC IC401 LA78040N-E 1 5 11 F 7 J801 1 F S
HV
60
CRT V801
DY
FRONT-AUDIO.R J707 2
FRONT-AUDIO.L J706
2 3 18 19 21 23 22
E-1
20AF46/20AF46C
E-2
W007
J702 D411 W135 D709 D702 D704 D701 C614 W134 C621
D404
C426
W857
W001 D405
W844
R4
D001 W819 W820 C514_1 S802X W077 W076 W075 W073 W862 R1010 S802Y W006 R1016 W017 W008 W059 R1001 R410_1 R416 W074 W072 D415 R407 R420 R517 R418 R427 IC401 D403 C645 W185 R422 VR401_1 C618
39
C425_1 CP401
TP004
IC504
IC1001 HS1001 C641 W187 W155 W151 W152 W154 R616 C622
W070 W068 W069 W067 W090 R617 W089 D602 C642 W024 C408 C407
Q503 W871
R507 Q505
HS501
S801Y
L1501
R6 49
W160
D510 B504
C5
C521_1
Q502
35
W146
R602 W144
R434
R542
D528
_1
D507
Q514 C512
Q606 W142 W143 W066 W164 R1503 C1504_1 Q604 C603 Q602 C608_2 C605
W027 C403
Q512
R541_1
R1515 B1502
W139
D605 W044 W041 C638 W030 W805 R132 W113 D607 D606 C139 W035 W032 W037
D517 D514
D508
D502
RY501
C503_1
CD801B CP801B
CP802B CD802B
R824 C801
D811 Q803
J8 01
C506_1
L1504 W837
CP508
C304 W833
W079
Q806
R302
CME017B
W053 W125 W129 W128 R140 R139 R119
L501
R807
L301 C314
R803
C505_1 CP501 R520
X101_1
W049 W050
CCE011B
2 80
R80
R301
C108
FH502 F501
FH501
J707
J706
J705
C916
F-1
CAUTION
R500
FOR SERVICE INFORMATION ABOUT CRITICAL COMPONENTS, SEE INSIDE BACK COVER.
C417_1
ATTENTION
W002 R443 C415_1 C508_1 R544 W004 R502 C507 W801 R539 D503
C733
D608
C413_1
W861
S803X
W133 W137 W138 W859 W018 C1501 C1515 C1514 R1507 W848 W179 W178 C1521 W177 W145 C1503 W014 W858 C1513_1 W162 W016 W015
C001_1
C725
C722
C619
TU001 C1009 W011 C626 L1503 R303 W165 R304 C316 C1006
C410
C420_1
R421
R429
R433
C509
R506
W087
C610
C539_1
X602
W825
R537
R45 2_1
W039 W033
W043
W806
D513
D520
W040
C519
W104
R623 D604 W096 C633 C306 C333 W095 C308 C305 C302
W105
W098
S803Y
W071 W103
W012
_1
S804Y D706
W092 W832
C502_1 TH501_2
D504
_1
C513_1
CP502
D106
R804
CP803
20AF46/20AF46C
F-2
C607 C624 R736 R726 C736 R636 R610 C640 R729 C738 R733 C612 1 C628 C616 R654
R1502
Q1507
Q1505
C002
C1523 R006
1 60 IC
F-3
C541 Q101 R532 R533 R810 C511 R801 R813 C811 R821 C554 R811 R815 C809 R819 R812 R809 R808 R817 R818 R820 C810 R814 R103 R106 R816 R513 R516 C805_1 R525
CCE011B
R109
C405
R114
R113 R101 R112 C106 R131 C119 C115 R137 R138 C121 C111 C117 R125 R409_1 C104 C416 R417 R415 C102 R403 Q103 IC101 R105 R401 R628 R627 R110 C143 R128 R134 R127 R136 R141R142 R129 W811 C141 C140 C128 C125 C131 C146 C145 R122 R150 C120 R126
SOLDER SIDE
CME017B
IC199_1
R143
R135
R629 R625 R912 R652 R653 R641 R635 49 R1514 C1509 C1510 C1508 IC1503 C1511 Q1501 IC1501 C1502 R1505 C1519 C1517 C1516 R1506 R1504 C1522 C1518 C1526_1 17 R611 R620 R609 R621 C625 R651 C142
C908
C303 C301 R314 C307 C309 C334 C311 C310 C313 C315 IC302 C320 C322 C1507 C1505 R1518 Q1502 R1513 R1508 C312
IC902
C741
C742
20AF46/20AF46C F-4
ACCESSORY
8
BT001 MNAAA(R03) 47 1/4W
R102
BT002 MNAAA(R03)
R120
TM101 RC-GQ020
270 1/4W
D109 SLR-342VCT32
POWER ON
C108
25V 10
2.7
KA
R101
560 R103 2.7K SW101 EVQ21505R SW103 EVQ21505R SW102 EVQ21505R VOL DOWN CH DOWN VOL UP CH UP
R106
560 SW104 EVQ21505R SW105 EVQ21505R POWER
C145 220P CH 1K 1/4W R124 C125 0.001 B 1.8 0 R122 0 CLAMP SW Q103 KTC3875S_Y_RTK
AUDIO L AUDIO R
R150 1K
100 1/4W
R146
6
TO SOUND
MICON IC IC101 5.0 1 AUDIO MUTE EXT MUTE VOLUME BBE SW AFT KEY 1 KEY 2 X RAY REMOCON ON_TIMER S_IN Y/C_SW AUDIO_SW 4.0 2 0 3 OEC7090B H_CTL PROTECT 12C_OFF SYNC H SYNC V SYNC BLUE B GREEN G RED R BLANK CLOCK_CNT SDA1 SCL1 42 0 R126 0 5.0 2.1 4.0 4.8 0 C131 0 0 0 R141 1.5K R142 R143 1.5K 5.0 NC 5.0 R135 5.0 R136 5.0 5.0 5.0 C115 2.4 C113 2.0 2.0 1.0 5.0 R125 10 VCC C109 0.1 B C128 0.1 YK 50V 0.47 KA C114 F 5.0 5.0 0 5.0 22 C117 47P CH R133 1K 1/4W C111 0.001 B 0.1 B R131 1K 220P C119 CH C121 0.01 B R132 100 1/4W C122 50V 1 KA 820P CH R138 1M 2 4.7K 4.7K R140 100 1/4W R139 100 1/4W 4 3 1.5K 150P CH R127 C138 6.8K R128 6.8K R129 6.8K 10 33 0 W811 D105 10P CH R145 2.2K C135 1SS133 B 100 C120 0.001 B C146 33P CH
1K
C143 220P CH
TV_MUTE VOLUME
39
C136
C137
0.1 B
0.1 B
0 4 3.2
40
41
OSD_G OSD_R D104 OSD_BLK 1SS133 SW_Y_OUT RESET POWER SDA SCL
R112
37
38
36
25V 10 KA
C139
34
5.0 9
35
0.1
11
S_IN Y/C_SW
32
0 0 5.0 0 NC 3.5
12
31
C141 220P CH
13
14
FROM/TO DEFLECTION 15 H_CTL 16 27 X-RAY MTZJ5.1B 5.0 3.2 NC 0 C102 C104 27P CH 27P CH 1 X101_1 100CT8R005 8MHz 1.7 0 2.3 28 R134 10K
29
30
0.1 B
C106
D106
17
18
25
26
20
19
X.OUT VSS
C110
R137
10K
MODE
5 SDA
6 SCL
8 VCC
W822
6.3V 2200
21
23
24
VSS
E2
E1
E0
PCB010 CME017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
G-1
20AF46/20AF46C
G-2
(MAIN PCB)
W831 FROM/TO COMB FILTER/AV R616 120 1/2W V_IN[YUV] VIDEO_IN1 R618 U_IN[YUV] Y_IN[YUV] VIDEO_IN3 KA R603 330 1/2W D602 1SS133 MTZJ8.2B 50V 1 KA 100 1/4W 8.2K R617 5.5 8.8 4.9 AT+5V REG Q607 KTC3203_Y
0.015 B
C631
18P CH
C632
16V 47 YK
50V 0.47 KA
X602 100DT3R531
16V 47 YK
50V 1 KA
3.579545MHz
C605
C611
0.1 B
C614
C607
C610
C630
D601
C619
C618
C621
C624
0.01
S804Y
C_V_OUT_SW Y_V_OUT_SW P.CON+5V VIDEO_OUT P.CON+8V[A] FSC_OUT 12 3W 10 3W 5.0 P.CON 5V REG Q602 KTC3209_Y 5.0 7.2 5.5 FROM/TO TUNER/STEREO 16V 47 YK 7 R602 R649 P.CON+5V REG Q606 KTC3209_Y 7.2 5.0 7.2 5.5 P.CON 5V REG Q604 KTC3209_Y C641 0.1 B 2.2 49
2.7 48
0 3.0 47 46 CVBS1
0 1.9 5.6 2.8 39 38 37 36 NC(GND) CVBS3 MCU 5.7 VREG OUT C_APC
0 3.2 35 34 NC(GND)
12
0.1
16V 47 YK
C622
50V
0.1
1K
S801X
FROM/TO MICON PROTECT 32 3.6 SW_Y_OUT 0 NC 5.0 3.5 NC 5.0 3.5 3.5 4.9 NC 4.2 2.9 C637 2.9 C643 2.9 C644 4.6 4.9 4.9 2.1 11 SYNC_OUT R629 6.8K D608 11E1-EIC CLAMP_OFF W805 33P CH 33P CH 33P CH R627 SCL 100 R628 SDA 100 POWER AT+5V RESET
0 33
50
51
52
MCU CLOCK OUT 47 NC(GND) 48 Y IN(YUV) 33 V/C GND 34 XTAL 3.58 SCL SDA CHROMA IC IC601 M61283BFP CLK CONT FAST BLK R IN 1 HVCO F/B 15 G OUT 2 AFC FILTER 16 B OUT G IN B IN V PULSE OUT HVCO F/BDEF GND1 INV.FBP OUT DEF GND2 DEF VCC MONITOR OUT HI VCC R OUT ACL 15 4.0 4.0 14 13 16 P_CON CONT
54
5.7V VREG OUT fsc OUT NC FAST YUV DELAYDE Y OUT EW OUT VIDEO LINE OUT 8.7 VREG OUT VRAMP AGC CAP LOGIC GND V OUT VRAMP CAP 1 3.2 4.0 2 0
27
53
28
29
8.7
30
3.0
31
55
C603
56
57
24
25
26
58
59
60
61
62
P.CON+5V 4.0 8 FROM POWER R621 22K 1/4W R601 UNREG+12V GND 15 1/2W P.CON 8V REG Q601 KTC3209_Y 2.2K P.CON 8V REG Q611 KTC3209_Y 11.3 8.5 7.9 0.33 TF 4.0
63
NC(Vcc)
NC(Vcc)
FBP IN
H OUT
64
NC
3 0
4 0
5 5.5
6 0
7 NC 3.8
8 8.0
9 8.0
10 0
11 8.0 NC
NC
13 4.0
14
17
18
19
20
8.7 4.0
21
TO SOUND
C608_2
3.0
22
23
R614
15
9 C633
C606
C615
C629 16V1000 YK
C612
R651
3.3K R652
3.3K R653
C638
16V 100 YK
D604 0.0047 B
0.01 B
0.01
1SS133 D606
C625
1SS133 D607
10K 1/4W
C645
C626
R611
0.01
0.1
16V 47 YK
MTZJ12B
C602
6.8K
100
R612
FROM/TO DEFLECTION
R609
1SS133
D605
1.5K
16V 10
C616
8.5 B
10
3.3K
7.9
11.3
120K B
KANP
R632
C609
5.6K
33K
R635 R636
R625
3
TO CRT CP802A (CP802B) B2013H02-6P P.CON+8V 1 2 3 4 5 6 GND
C628
100 1/4W
PCB010 CME017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-3
20AF46/20AF46C
G-4
16
12.0
25.0 17
4.0
1K
9 10 8 6 11
R G B 5 7 1
1K
7
R427 11E1-EIC D402
1K
7
1 2
TO CRT/SVM (CP805)
CD803_1 CH823006
R417 25V 1000 MHE R418 39K C408 1/2W 50V 1 YK 820 5601/2W MKT MTZJ30B C417_1
50V 10 YK
V.POSI ADJ
D403
100V0.22
C405
C409
R420
D410
1 1/2W
R416
W821 3.3
2.7
R422
V_OUT
GND P.CON+5V H.OUT H_SYNC ABCL 0.001 CH 19 MMTS H.OUT Q405 2SC5885 W871 0.1 R428 0 0.1 100 1/4W HS402 763WAAA072 0 W850 W853 W813 CMPP C411 21 R402 68 1/2W 4.7mH 250V 0909 2.2 YK C418 250V 0.39 PMS C410
5
R409_1 10K 1/4W 1K R403 1K H.DRIVE Q402 KTC3227_Y 17.3 0.4 R406 0 C402
1.25KV 0.012
C420_1
560
1/2W
MTZJ30B R437
1/2W
18K
FROM/TO CHROMA
20 T401_1 ETH14Y47AY 5 1 4
L401
115
FB401 TP004 PROTECTOR TEST TP003 115 COL 1 180 6 108.0 2 105.0 9 0 W857 10 8 E180 B+ AFC HEA TER GND
FJN20A002_M ANORD HV
0.01 100V
R453
C403
FROM/TO POWER
470 1/2W
50V 22 YK
17.3 0 26.3
GND R434 +B 5.6 10W W863 R452_1 180 1W D414 11E1-EIC D415 11E1-EIC R410_1 150 2W D405 AU02A-EIC W861
FORCUS F FROM/TO CRT S GND 0 11 ABL 8.1 R443 150K 1/2W SCREEN
FBT+B H+B
8 0.1 E8 NC 5
FROM/TO MICON
100K
3
AU02A-EIC D407 R438_1 R436 18K1/4W+-1% B C439 R441 15K +-1% 100V 22 YK C430 2.7 1W D411 AU02A-EIC 35V 1000 YK
H_CTL X-RAY
C413_1
MHE
C426
0.001
TP005
TP006
250V 22
D406
R426
X-RAY TEST
PCB010 CME017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-5
20AF46/20AF46C
G-6
(MAIN PCB)
7
2.7M 1/2W +-10% RY501 G5PA-1-SA(WEC) 2 3 DEGAUSS COIL L503 8R200024 1 2 C505_1 275V 0.22 ECQUL 1 CP502 A1561WV2-2P 1
250V0.0015 KX
S802X R541_1 0.22 1W R501 RM11C-EIC D501 D502 1 7W R539 1.2M 1/4W 1.2M 1/4W RM11C-EIC D505 25V 2200 YK 30PRA60-FC C501 R517
S802Y TO SOUND
W806
R500
C519_1
GND SOUND_GND
C502_1
C503_1
1/2W
C507
1SS133
6
TH501_2 BLADE WIDE CP501 A3963WV2-3PD 2 2 WHITE 1 1 BLACK WHITE F501 BLACK 6.3A125V FH501 FH502 EYF-52BCY EYF-52BCY 6.3A125Vor51MS063L 1 CP508 B59203-S1060-B14 003P-2100
200V470 UP
CP507 003P-2100 1
D517 R503 10K 1/4W D514 38 R537 100K 1/4W 115.4 +B SW. Q503 2SA1371 C539_1 R505 100V 2.2 YK R536 3.9K 1/4W 47K 1/4W R535 B504 220P CH D510 R527 0.68 2W 160V 220 ED 115.5 10K 1/4W 115.1 114.7 82K 1/4W R507 1SS133 FROM/TO DEFLECTION H+B +B FBT+B GND
2KV0.001 RR 2KV0.001 RR
R540
RM11C-EIC
R520 1.5M
D503
C506_1
D504
D523
RM11C-EIC
MTZJ18B
T501 8
8135091S
50.0
9 P1 7 10 NC
2KV 0.0015 RR
141.6 0
6
25.0 0
11
W825
BL02RN1-R62 159.4 2KV 0.0022 RR C535_1 159.4 D 0 S SWITCHING Q502 2SK3326(2) G 5.3 5.3 SWITCHING Q514 KTC3203_Y R544 R542 270 1/4W D507 1SS133 R545 150 1/4W D524 1SS133
13 R502 330 2W 1.5 500V 0.001 B C524 0 C512 100V 0.047 MMTS 2 HS501 763WAAA074 1 16
138.9
3 14
26.0 15
C521_1
C511
6.3A 125V
W801
B501
40.0
5
P2
W5RH3.5X5X1.0 FE201-6L49
240.0 12 NC
FROM/TO MICON D511 1N4937 R546 50V 2.2 YK 100 1/4W C504 R524 P.FAIL R525 3.3K 1/4W 15K X-RAY DEGAUSS_H POWER GND C520
0.15
1W
FEED BACK IC504 LTV-817M-VB 10.7 1 C554 2 0.022 B 6.3 W817 1/2W 5.7 9.7 FEED BACK SWITCHING Q507 KTC3198 R532 6.8K 1.5K R510 100K 1/2W R554 R533 270 3 9.7 1.5 16.3 4 D509 MTZJ18B
R508
D506
25V 47 YK R543
0.056
1K 1/4W
C541
6.8K 1/4W
3
R506
R553
C509
MTZJ5.6B
250V 0.0022 KX
100 1/4W
+B ADJ
16V 2200 YK
D528
CAUTION:
MTZJ3.9B D508
MTZJ12B
D525
100 1/4W
1SS133
D520
VR502 22K
C527
C508_1
R547
2
PCB010 CME017
6.3A 125V
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-7
20AF46/20AF46C
G-8
(MAIN PCB)
50V 10 YK
220K C333
R314
C315
0.1
0.015 B
C307
C319
FROM TUNER/STEREO
SW_AUDIO_L SW_AUDIO_R 22
50V 10
YK
7
50V 10 YK 0.033 B C309 0.039 B NC 4 NC 0 NC 5 NC 3.9 6 PF2 3.9 7 PF3 3.9 8 PF4 0 9 GND 4.0 10 LT 4.0 11 LB 0 NC 12 NC 0 NC 13 NC 2.0 14 BD 50V 10 YK 2.9 15 C304 0.01 B C310 C313 C317
1.7 2 AGC
3.0 3 L IN
4.0 16 VD L ONT
AGC
SURR
Tone Control
+ + NC 21 0 NC 0 NC 20 NC
Balance /MUTE
R IN 30 4.5 C305
6
NC 28 NC 0 NC 27 NC 4.0 BB 26 RB RT BLD TD 25 24 23 22 4.0 4.4 3.0 2.0 R OUT SDA SCL 19 18 17 4.0 3.5 3.5
50V 10 YK
50V 10 YK
0.01 B
C312
C316
C308
50V 10 YK
C302
C334
50V 10 YK
C314
1 B
100 1/4W
0.01 B
C306
C311
P.CON+8V[A]
0.1 B
56P CH C322
C303
SCL VOLUME 68K 1/4W R1015 TV_MUTE 25 7 SOUND AMP IC 68K 1/4W R1014 IC1001 AN7522N C1011 16V 47 KA C1012 R1012 150 1/2W R1013 3 16V 47 KA 150 1/2W 4 5 1 6 2 HEADPHONE JACK J1001 MSJ-2000_AG
56P
C320
CH
1/4W
R1001
24
68K
47K 1/4W
+
1 6.3 8.5 2 0 3 8.6
4 3.9 5 2.4
L 6 0 7 2.5
R 8 2.1 9 8.5
10 0 11 8.5
+
12 W858 CD1001 CU14411A 4 3 2 1
SOUND+B
C1003 1 B
3
SPEAKER L SP1001 YDP512-22 8 OHM CP1001 A2502WV2-4P
SP OUT L+ S801Y SP OUT LSP OUT RSP OUT R+ 50V 0.33 KA 50V 22 YK 100K 1/4W C1001 390P B C1002 R1003 C1007 F B R1008 R1010
4 3 2 1
SPEAKER R
270K
0.0012
R1006
1M
C1004
C1005
100K
HS1001 763WAA0295
0.0012 B
R1017
C1006
1M
26 27
PCB010 CME017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-9
20AF46/20AF46C
G-10
(MAIN PCB)
TU001
115-V-KA35ARB 9 (ADRESS) 14 SIF OUT 8 (XTAL) 16 IF OUT AUDIO OUT VIDEO OUT
20
19
7
S803X FROM/TO CHROMA TUNER+5V TUNER_VIDEO
11 SDA
10 SCL
12 AFT
MB
MB
15 BT
13
17
21
18
NC W812
NC
NC
NC
NC
NC NC
NC
NC
NC
6.3V 330 YK
C001_1
R006
100
0.1
C005
6
MTZJ33B
D001
FROM POWER W820 R001 P.CON+B 68K 1/2W R002 68K 1/2W GND
W819
FROM/TO MICON
4
R912 330 C919 50V 10 YK
TO SOUND L901 0.047 B C913 0.1 B SW_AUDIO_L SW_AUDIO_R C911 100uH 0305 0.1 B C917
3
SOUND DECORDER IC IC902 AN5829S-E1V 24 2.3 23 2.3 22 2.3 21 2.3
DAC
W829
NC 20
19
5.0
18
5.0
GND
17
16
3.7
15
3.6
14
2.6
13
Det SAP
3.7
AGC Matrix
OUT SW
ZAP IIC Decoder L-R Filter L+R Filter L-R Demod L+R Demod
VCA Input
Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset
Vcc
8 2.4
10 0.4
12 3.4 0.1 B
5.1 C910
2
10V 100 YK C916
50V 4.7 KA
0.022 B
0.022 B
C912
C905
0.1 B
C908
C915
PCB010 CME017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
G-11
20AF46/20AF46C
G-12
(MAIN PCB)
VIDEO SW(Y) IC IC1502 MM1501XNRE C1503 50V 4.7 KA C1514 R1509 1K R1510 220 4 3 4.5 Vin2 Vcc 7.9 5 2 0 GND V.OUT 4.4 S_IN 6 1 4.5 Vin1 SW1 0 FROM/TO MICON
L1507
W848
W865
A.GND
22uH
Y/C_SW
10V 100 YK BUFFER Q1502 KTC3875S_Y_RTK 2.0 3.5 2.6 R1518 6.8K C1521 0.1 B
R1502
7
C1502 47P CH
B1502
1K
C1511 0.01 B C1512 0 0.6 0 BUFFER Q1501 2SA1037AK C1504_1 R1503 16V 100 YK
R1508 1K R1513 3.3K D.VCC KILLER TEST BIAS1 ADin VRT VRB A.VSS D.VSS CKin V.FIL BIAS3 C.OUT BIAS2 Y.OUT A.VDD 8 9
VIDEO SW(C) IC IC1503 MM1501XNRE R1507 1K 1/4W C1501 16V 10 KANP 5 2 0 4.5 3.5 3.5 2.9 R1516 C1523 F 0.1 GND Vin2 V.OUT Vcc 4.4 7.9 16V 100 YK L1501 6 1 4.5 0 Vin1 SW1
FROM/TO CHROMA
Y_V_OUT_SW C_V_OUT_SW P.CON+8V[A] 100uH 0305 C1532 P.CON+5V FSC_OUT VIDEO_OUT V_IN[YUV]
5.2 10 7 1K 1/4W 0 50V 0.47 KANP 0.01 F C1507 6 0 C1509 12 5 0.01 B 1.2 2.5 560 1/4W R1511 C1508 14 3 0.1 B 2.9 C1510 0.01 B 2.3 1 0 2 4
0 C1515 2.3 2.2 C1516 3.5 0.01 B R1504 100 C1517 0.01 B R1505 100 0.01 B
11
13 2.9 1.5
C1526_1 L1504 15uH 0305 R1506 BUFFER Q1507 KTC3875S_Y_RTK 3.5 56P CH
15 3.5 16 5.1 CH
10V 100 YK
C1513_1
820
3 2.2
R1514
C1519
0.01 B
180P
C1518
W837
R1517 1K
FROM/TO POWER
GND
H2
S804X
4
LINE1(REAR) J701 MSP-213V2-432_NI_LF 4
H1 NC H1 H2 E
H1
4
TO TUNER/STEREO
1 5
E
C736
D704
AUDIO_IN2[R] 75 C733 KA
R739
16V 22 75
MTZJ6.2B R735 1
H
D709
75 FRONT-VIDEO J705 MTJ-032-03A-30FE MTZJ12B FRONT-AUDIO.L J706 MTJ-032-03A-32FE LINE3_A_IN_L FRONT-AUDIO.R J707 MTJ-032-03A-31FE 0.0056 B C741
NC
D706
75
2
1
H
R724
2
R745 1K C719 1 B
NC
NC
R746 1K
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
G-13
20AF46/20AF46C
G-14
(CRT PCB)
FROM DEFLECTION
CP806 005P-2100
1 2 3 4 5
180V NC NC GND HEATER FROM CHROMA C805_1 CP802B (CP802A) B2013H02-6P RED/GREEN OUT Q804 2SC4217 220
R802
38
FOCUS
R803 15K 2W
2.7K
1/4W
0.1 F
1 2 3 4 5 6
R801
123.0 7.4 D801 1SS133 37 6.9 14F:GREEN OUT 27":RED OUT R806 2.7K 1/4W
3.2 2.7
R809 2.2K GREEN/RED OUT Q803 98.4 KTC3199_Y C811 470P CH R813 330 R817 220
R807 15K
2W
R808
220
D811 R820 100 (27"GREEN) 1SS133 R814 2.2K BLUE OUT Q802 KTC3199_Y
2.7
96.4
3.2
R818 220
96.4 8
7 6 5 4
R805 15K
2W
2.7K 1/4W
0 0
95.4 2.7
C809 560P CH R815 330 R819 220
BLUE OUT Q806 2SC4217 128.0 7.4 D803 1SS133 7.0 BLUE OUT
R810
220
1
0
3.2
R811 2.2K
PCB110 CCE011
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
THESE PARTS MARKED BY CAUTION:SINCE CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
PIECES REPAREES PAR UN ETANT ATTENTION:LES DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
G-15
20AF46/20AF46C
G-16
WAVEFORMS
MICON
1 1V 0.1 s/div
0.5V 10ms/div
13 1V 20 s/div
2 1V 1 s/div
9 1V 50 s/div
14 2V 20 s/div
3 1V 50 s/div
10 2V 20 s/div
15 2V 20 s/div
DEFLECTION
4 1V 0.1ms/div
11 0.5V 20 s/div
16 2V 5ms/div
CHROMA
7 1V 20 s/div
12 1V 2 s/div
17 20V 5ms/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
20AF46/20AF46C
WAVEFORMS
18 10V 10ms/div
38 50V 20 s/div
25 2V 5ms/div
19 20V 20 s/div
39 50V 20 s/div
26 0.5V 1ms/div
SOUND
20 2V 20 s/div
22 2V 5ms/div
27 0.5V 1ms/div
COMB FILTER/AV
21 200V 50 s/div
23 2V 5ms/div
28 200mV 20 s/div
CRT
37 50V 20 s/div
24 2V 5ms/div
29 200mV 20 s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
20AF46/20AF46C
202
201
112
110
111
209
112 110
203
108
209
111
203
126
111
204 101F 101H 101G
209 203
108
209
101I
101G
111
203
101B
114 117
118
113
124
116
I-2
20AF46/20AF46C
TSB P/N
72781165 72799331 72782969 72782972 72799677 72783010 72794719 72799770 72799793 72794722 72781183 72799347 72798774 72795687 72783310 72783311 72794734 72783312 72798661 72798684 72798781 72794733 72798782 72783313 72795702 72798704 72798705 72783314 72781105 72783330 72781628 72781569 72783315 72795703 72781287 72781279 72781276 72798791 72798786 72798789 72781251 72781255 72781295
Reference No.
7A701A423A 701WPJD026 711WPA0184 713WPA0263 7235490049 735WPA0728 735WPA0732 735WPBB393 735WPJA853 800WQ0A070 7A702A089A 702WPAA806 800WQ0A045 741WUA0021 722549A582 723000D284 899HV3T000 726000A134 761WPA0220 762WPA0011 800WR0A002 801WR00001 800WR0A026 723000D285 791WHAA114 792WHA0432 792WHA0433 793WCDD103 795WCDA011 A3S1032975 JA4ND200 J3N51617A J3S10321A 791WHAA134 8141J50C5U 8117540A6U 8117140A2U 8110630A0U 810763080U 8109I30A0U 810963080Q 8109I3080U 8162540A6U
Description
FRONT CABI ASS'Y CABINET FRONT PLATE FRONT GLASS LED BADGE BRAND STOPPER BUTTON 1 STOPPER BUTTON 2 BUTTON FRAME BUTTON POWER FELT SHEET BACK CABI ASS'Y CABINET BACK FELT SHEET SPRING EARTH SHEET RATING POP LABEL HOLDER ANODE WIRE SHEET CRT SERVICEMAN HOLDER SPEAKER HOLDER CRT WIRE SHEET CRT SUPPORT DAMPER SPEAKER SHEET CRT SUPPORT (D) SHEET BARCODE FILM BAG PACKAGE TOP PACKAGE BOTTOM GIFT BOX PAD INSTRUCTION BOOK KIT POLYBAG INSTRUCTION(RED CAUTION) REGISTRATION CARD INSTRUCTION BOOK(E/S) LIGHTRON SHEET SCREW TAP TITE(P) GW22 5*35 CH HEXAGON SCREW TAP TITE(B0) TRUSS 4*16 CH SCREW,TAPPING(B0) PAN 4*12 CH SCREW TAP TITE(P) BRAZIER 3*10 CH SCREW TAP TITE(S) BRAZIER 3*8 CH SCREW TAP TITE(B) WH7 3*10 CH SCREW TAP TITE(B) BRAZIER 3*8 STAINLESS SCREW TAP TITE(B) WH7 3*8 CH SCREW TAPPING (BO) WASHER 18
J1-1
20AF46
TSB P/N
72781165 72799331 72782969 72782972 72799677 72783010 72794719 72799770 72799793 72794722 72781183 72799347 72798774 72795687 72783321 72783322 72794734 72783312 72798661 72798684 72798781 72794733 72798782 72783323 72795702 72798704 72798705 72783324 72781105 72783325 72795600 72783326 72795703 72798549 72795593 72795594 72781287 72781279 72781276 72798791 72798786 72798789 72781251 72781255 72781295
Reference No.
7A701A423A 701WPJD026 711WPA0184 713WPA0263 7235490049 735WPA0728 735WPA0732 735WPBB393 735WPJA853 800WQ0A070 7A702A089A 702WPAA806 800WQ0A045 741WUA0021 722549A573 723000D261 899HV3T000 726000A134 761WPA0220 762WPA0011 800WR0A002 801WR00001 800WR0A026 723000D262 791WHAA114 792WHA0432 792WHA0433 793WCDD079 795WCDA011 A3S007S975 JA4ND100 J3S00721A 791WHAA134 7230007398 722000A023 722000A267 8141J50C5U 8117540A6U 8117140A2U 8110630A0U 810763080U 8109I30A0U 810963080Q 8109I3080U 8162540A6U
Description
FRONT CABI ASS'Y CABINET FRONT PLATE FRONT GLASS LED BADGE BRAND STOPPER BUTTON 1 STOPPER BUTTON 2 BUTTON FRAME BUTTON POWER FELT SHEET BACK CABI ASS'Y CABINET BACK FELT SHEET SPRING EARTH SHEET RATING POP LABEL HOLDER ANODE WIRE SHEET CRT SERVICEMAN HOLDER SPEAKER HOLDER CRT WIRE SHEET CRT SUPPORT DAMPER SPEAKER SHEET CRT SUPPORT (D) SHEET BARCODE FILM BAG PACKAGE TOP PACKAGE BOTTOM GIFT BOX PAD INSTRUCTION BOOK KIT POLYBAG INSTRUCTION(RED CAUTION) INSTRUCTION BOOK(E/F) LIGHTRON SHEET SECURITY TAG SHEET HWC SHEET CSA WARNING SCREW TAP TITE(P) GW22 5*35 CH HEXAGON SCREW TAP TITE(B0) TRUSS 4*16 CH SCREW,TAPPING(B0) PAN 4*12 CH SCREW TAP TITE(P) BRAZIER 3*10 CH SCREW TAP TITE(S) BRAZIER 3*8 CH SCREW TAP TITE(B) WH7 3*10 CH SCREW TAP TITE(B) BRAZIER 3*8 STAINLESS SCREW TAP TITE(B) WH7 3*8 CH SCREW TAPPING (BO) WASHER 18
J1-2
20AF46C
TSB P/N
72781748 72795508 72797795 72794682 72794599 72795116 72795517 72781753 72796031 72795516 72797842 72794631 72795523 72795503 72794616 72796002 72795500 72794624 72794633 72795513 72797913 72794641 72796459 72796459 72796459 72794410 72797426 72794389 72797697 72794399 72794394 72794396 72795574 72794399 72794399 72795091 72795566 72795567 72795573 72794403 72797128 72795574 72795581 72797128 72795629 72781390 72796330 72796327 72795577 72794440 72794465 72794491 72794491 72794469 72795529 72794488 72794471 72794469 72794472 72794489 72794472 72794471 72794472 72794488 72794488 72794473 72794473 72794473 72794473 72794474 72794483 72794491 72795542
Reference No.
R638U2680J R3X18A151J R002T23R3J R002T22R7J R4X5T4472F R5X2CF5R6J R4X5T4183F R655812R7J R3K181102J R4X5T6153F R3X181181J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R3X28BR22J R002T2155J R3X18AR68J R63881R22J R3X181R15J R3X28B120J R3X28B100J R3X18A153J R3X18A153J R3X18A153J E5EZF3102M E0ELF4102M P4J7F3394J P4N8FJ123H C0PLRR713K E5EZFD220M E02LU8220M E02LF3222M C0PLRR713K C0PLRR713K E02LU52R2M P2122B224M P2122B104M E51CGC471M CD39E0MH3M CD39E0ME3M E02LF3222M C0PLRR7E3K CD39E0ME3M C0JTB0513K E61DFB221M E02LF2222M C0PLRR7H3K CQG0B04Q3K C0JBB07H3K D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D97U03001B D2WTAU02A0 D2WT011E10 D2WT011E10 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F0PRA60 D2WXN49370 D1VT001330 D97U03R91B
Description RESISTORS
R,FUSE R,METAL OXIDE RC RC R,METAL R,CEMENT R,METAL R,FUSE R,METAL OXIDE R,METAL R,METAL OXIDE RC R,C R,METAL OXIDE RC R,METAL OXIDE RC R,METAL OXIDE R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 68 OHM 1/2W 150 OHM 2W 3.3 OHM 1/2W 2.7 OHM 1/2W 4.7K OHM 1/4W 5.6 OHM 10W 18K OHM 1/4W 2.7 OHM 1W 1K OHM 1W 15K OHM 1/6W 180 OHM 1W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 0.22 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 0.22 OHM 1W 0.15 OHM 1W 12 OHM 3W 10 OHM 3W 15K OHM 2W 15K OHM 2W 15K OHM 2W 1000 UF 25V 1000 UF 35V 0.39 UF 250V PMS 0.012 UF 1.25KV 0.001 UF 2KV R 22 UF 250V 22 UF 100V 2200 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 0.0022UF 250V 0.0015UF 250V 2200 UF 25V 0.0015 UF 2KV R 0.0015UF 250V 0.001 UF 500V B 220 UF 160V 2200 UF 16V 0.0022 UF 2KV R 0.0047UF 50V B 0.0022UF 2KV B
CAPACITORS
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! CE CE CMPP CMPP CC CE CE CE CC CC CE CMP CMP CE CC CC CE CC CC CC CE CE CC CC CC
DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30PRA60-FC 1N4937 1SS133T-77 MTZJ3.9B T-77
! ! ! !
! ! ! ! ! !
J2-1
14AF46
TSB P/N
72795541 72794475 72794483 72794480 72794491 72794491 72794491 72794491 72794491 72795541 72794491 72794487 72794489 72794491 72794486 72794487 72794491 72794491 72794491 72794488 72794487 72794487 72794487 72794487 72794487 72794490 72794491 72794491 72794491 72794491 72794491 72794491 72795533 72782885 72794498 72795534 72795524 72794514 72795535 72795908 72794500 72794502 72794502 72794571 72794571 72794561 72782813 72795540 72795475 72794577 72795474 72794577 72794569 72795476 72794570 72794570 72794570 72794570 72795476 72794570 72794573 72794573 72794573 72795971 72795971 72795971 72795970 72794571 72794571 72794571 72794540 72794527
Reference No.
D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01201B D97U05R61B D1VT001330 D97U08R21B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 I56F07090B A3S001U015 I01FF58910 I03TD804N0 0002E00610 I06FC1283B I01FF58290 I0FSP7522N I05FEA45FG I0UF015010 I0UF015010 TCAA3875SY TCAA3875SY TCAT03227Y TC1G058850 T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAT03209Y TCAT03209Y TCAT032034 TCAT03209Y TCATC3199Y TCATC3199Y TCATC3199Y TC3F042170 TC3F042170 TC3F042170 T6YJ1037K0 TCAA3875SY TCAA3875SY TCAA3875SY 02167F101J 021679472K
Description DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ12B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7090B BR24L16FJ-WE2 AN5891SA-E1V LA78040N-E LTV-817M-VB M61283BFP AN5829S-E1V AN7522N TC90A45FG MM1501XNRE MM1501XNRE KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SC5885 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT 2SC4217(D,E)-RAC 2SC4217(D,E)-RAC 2SC4217(D,E)-RAC 2SA1037AKT146R,S KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 100 UH 4.7 MH
ICS
IC INIT DATA IC IC PHOTO COUPLER IC IC IC IC IC IC
TRANSISTORS
! ! ! ! ! ! ! ! TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON
! ! ! ! ! !
COILS &TRANSFORMERS
COIL COIL
J2-2
14AF46
TSB P/N
72794528 72796630 72795933 72794540 72794540 72795062 72795932 72796571 72796055 72798977 72794518 72794517 72795493 72794519 72794520 72794521 72795490 72794516 72794688 72794688 72794688 72794688 72794688 72795471 72794701 72783316 72783317 72795549 72794357 72794357 72783174 72783174 72795553 72798401 72798421 72783318 72782677 72782003 72796817 72796821 72796768 72796768 72796816 72796824 72783319 72796793 72796751 72796751 72796752 72796752 72795888 72797070 72797069 72794493 72796667 72794496 72794496 72794541 72794686 72799164 72799164 72794693 72799199 72795492 72783320 72794702 72794704
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE HEADPHONE JACK
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT
VARIABLE RESISTORS
VOLUME,SEMI FIXED VOLUME,SEMI FIXED
P.C.BOARD ASSEMBLIES
PCB ASS'Y PCB ASS'Y
MISCELLANEOUS
CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH FLAT CABLE FLAT CABLE CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER CUSHION C EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
! ! !
! !
! ! ! ! ! !
J2-3
14AF46
J2-4
14AF46
TSB P/N
72781748 72795508 72797795 72794682 72794599 72795116 72795517 72781753 72796031 72795516 72797842 72794631 72795523 72795503 72794616 72796002 72795500 72794624 72794633 72795513 72797913 72794641 72796459 72796459 72796459 72794410 72797426 72794389 72797697 72794399 72794394 72794396 72795574 72794399 72794399 72795091 72795566 72795567 72795573 72794403 72797128 72795574 72795581 72797128 72795629 72781390 72796330 72796327 72795577 72794440 72794465 72794491 72794491 72794469 72795529 72794488 72794471 72794469 72794472 72794489 72794472 72794471 72794472 72794488 72794488 72794473 72794473 72794473 72794473 72794474 72794483 72794491 72795542
Reference No.
R638U2680J R3X18A151J R002T23R3J R002T22R7J R4X5T4472F R5X2CF5R6J R4X5T4183F R655812R7J R3K181102J R4X5T6153F R3X181181J R0G3K2275K R5X2AE010J R3X28A331J R002T4682J R3X28BR22J R002T2155J R3X18AR68J R63881R22J R3X181R15J R3X28B120J R3X28B100J R3X18A153J R3X18A153J R3X18A153J E5EZF3102M E0ELF4102M P4J7F3394J P4N8FJ123H C0PLRR713K E5EZFD220M E02LU8220M E02LF3222M C0PLRR713K C0PLRR713K E02LU52R2M P2122B224M P2122B104M E51CGC471M CD39E0MH3M CD39E0ME3M E02LF3222M C0PLRR7E3K CD39E0ME3M C0JTB0513K E61DFB221M E02LF2222M C0PLRR7H3K CQG0B04Q3K C0JBB07H3K D97U03301B D1VT001330 D1VT001330 D97U05R11B 0021721150 D2WT011E10 D97U03001B D97U05R11B D2WTAU02A0 D97U05R61B D2WTAU02A0 D97U03001B D2WTAU02A0 D2WT011E10 D2WT011E10 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D2WTRM11C0 D28F0PRA60 D2WXN49370 D1VT001330 D97U03R91B
Description RESISTORS
R,FUSE R,METAL OXIDE RC RC R,METAL R,CEMENT R,METAL R,FUSE R,METAL OXIDE R,METAL R,METAL OXIDE RC R,CEMENT R,METAL OXIDE RC R,METAL OXIDE RC R,METAL OXIDE R,FUSE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE 68 OHM 1/2W 150 OHM 2W 3.3 OHM 1/2W 2.7 OHM 1/2W 4.7K OHM 1/4W 5.6 OHM 10W 18K OHM 1/4W 2.7 OHM 1W 1K OHM 1W 15K OHM 1/6W 180 OHM 1W 2.7M OHM 1/2W 1 OHM 7W 330 OHM 2W 6.8K OHM 1/4W 0.22 OHM 3W 1.5M OHM 1/2W 0.68 OHM 2W 0.22 OHM 1W 0.15 OHM 1W 12 OHM 3W 10 OHM 3W 15K OHM 2W 15K OHM 2W 15K OHM 2W 1000 UF 25V 1000 UF 35V 0.39 UF 250V PMS 0.012 UF 1.25KV 0.001 UF 2KV R 22 UF 250V 22 UF 100V 2200 UF 25V 0.001 UF 2KV R 0.001 UF 2KV R 2.2 UF 50V 0.22 UF 275V ECQUL 0.1 UF 275V ECQUL 470 UF 200V 0.0022UF 250V 0.0015UF 250V 2200 UF 25V 0.0015 UF 2KV R 0.0015UF 250V 0.001 UF 500V B 220 UF 160V 2200 UF 16V 0.0022 UF 2KV R 0.0047UF 50V B 0.0022UF 2KV B
CAPACITORS
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! CE CE CMPP CMPP CC CE CE CE CC CC CE CMP CMP CE CC CC CE CC CC CC CE CE CC CC CC
DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER MTZJ33B T-77 1SS133T-77 1SS133T-77 MTZJ5.1B T-77 SLR-342VCT32 11E1-EIC MTZJ30B T-77 MTZJ5.1B T-77 AU02A-EIC MTZJ5.6B T-77 AU02A-EIC MTZJ30B T-77 AU02A-EIC 11E1-EIC 11E1-EIC RM11C-EIC RM11C-EIC RM11C-EIC RM11C-EIC 30PRA60-FC 1N4937 1SS133T-77 MTZJ3.9B T-77
! ! ! !
! ! ! ! ! !
J2-5
14AF46C
TSB P/N
72795541 72794475 72794483 72794480 72794491 72794491 72794491 72794491 72794491 72795541 72794491 72794487 72794489 72794491 72794486 72794487 72794491 72794491 72794491 72794488 72794487 72794487 72794487 72794487 72794487 72794490 72794491 72794491 72794491 72794491 72794491 72794491 72795533 72783327 72794498 72795534 72795524 72794514 72795535 72795908 72794500 72794502 72794502 72794571 72794571 72794561 72782813 72795540 72795475 72794577 72795474 72794577 72794569 72795476 72794570 72794570 72794570 72794570 72795476 72794570 72794573 72794573 72794573 72795971 72795971 72795971 72795970 72794571 72794571 72794571 72794540 72794527
Reference No.
D97U01801B D2CF2016L0 D2WXN49370 D28T21DQN9 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U01801B D1VT001330 D97U01201B D97U05R61B D1VT001330 D97U08R21B D97U01201B D1VT001330 D1VT001330 D1VT001330 D2WT011E10 D97U01201B D97U01201B D97U01201B D97U01201B D97U01201B D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 I56F07090B A3S002U015L I01FF58910 I03TD804N0 0002E00610 I06FC1283B I01FF58290 I0FSP7522N I05FEA45FG I0UF015010 I0UF015010 TCAA3875SY TCAA3875SY TCAT03227Y TC1G058850 T220033260 TA3T1371A0 TCATC31980 TC3T029090 TCATC31980 TA3T016240 TCAT032034 TCAT03209Y TCAT03209Y TCAT03209Y TCAT03209Y TCAT032034 TCAT03209Y TCATC3199Y TCATC3199Y TCATC3199Y TC3F042170 TC3F042170 TC3F042170 T6YJ1037K0 TCAA3875SY TCAA3875SY TCAA3875SY 02167F101J 021679472K
Description DIODES
DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON MTZJ18B T-77 FE201-6L49 1N4937 21DQ09N-TA2B1 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ18B T-77 1SS133T-77 MTZJ12B T-77 MTZJ5.6B T-77 1SS133T-77 MTZJ8.2B T-77 MTZJ12B T-77 1SS133T-77 1SS133T-77 1SS133T-77 11E1-EIC MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ12B T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 OEC7090B AN5891SA-E1V LA78040N-E LTV-817M-VB M61283BFP AN5829S-E1V AN7522N TC90A45FG MM1501XNRE MM1501XNRE KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3227_Y-AT 2SC5885 2SK3326(2) 2SA1371(D,E)-AE KTC3198-AT(Y,GR) 2SC2909(S,T)-AA KTC3198-AT(Y,GR) 2SA1624-AA KTC3203_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3209_Y-AT KTC3203_Y-AT KTC3209_Y-AT KTC3199_Y-AT KTC3199_Y-AT KTC3199_Y-AT 2SC4217(D,E)-RAC 2SC4217(D,E)-RAC 2SC4217(D,E)-RAC 2SA1037AKT146R,S KTC3875S_Y_RTK KTC3875S_Y_RTK KTC3875S_Y_RTK 100 UH 4.7 MH
ICS
IC INIT DATA IC IC PHOTO COUPLER IC IC IC IC IC IC
TRANSISTORS
! ! ! ! ! ! ! ! TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON
! ! ! ! ! !
COILS &TRANSFORMERS
COIL COIL
J2-6
14AF46C
TSB P/N
72794528 72796630 72795933 72794540 72794540 72795062 72795932 72796571 72796055 72798977 72794518 72794517 72795493 72794519 72794520 72794521 72795490 72794516 72794688 72794688 72794688 72794688 72794688 72795471 72794701 72783328 72783317 72795549 72794357 72794357 72783174 72783174 72795553 72798401 72798421 72783318 72782677 72782003 72796817 72796821 72796768 72796768 72796816 72796824 72783319 72796793 72796751 72796751 72796752 72796752 72795888 72797070 72797069 72794493 72796667 72794496 72794496 72794541 72794686 72799164 72799164 72794693 72799199 72795492 72783320 72794702 72794704
JACKS
RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY,TUBE HEADPHONE JACK
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT
VARIABLE RESISTORS
VOLUME,SEMI FIXED VOLUME,SEMI FIXED
P.C.BOARD ASSEMBLIES
PCB ASS'Y PCB ASS'Y
MISCELLANEOUS
CORE,BEADS CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH FLAT CABLE FLAT CABLE CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER WIRE HOLDER WIRE HOLDER CUSHION C EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL CRYSTAL
! ! !
! !
! ! ! ! ! !
J2-7
14AF46C
J2-8
14AF46C
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN