Professional Documents
Culture Documents
I LOW INPUT BIAS AND OFFSET CURRENT I LOW NOISE en = 15nV/Hz (typ) I OUTPUT SHORT-CIRCUIT PROTECTION I HIGH INPUT IMPEDANCE JFET INPUT
STAGE
N DIP14 (Plastic Package)
I LOW HARMONIC DISTORTION : 0.01% (typ) I INTERNAL FREQUENCY COMPENSATION I LATCH UP FREE OPERATION I HIGH SLEW RATE : 13V/s (typ)
D SO14 (Plastic Micropackage)
DESCRIPTION The TL074, TL074A and TL074B are high speed JFET input quad operational amplifiers incorporating well matched, high voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view)
ORDER CODE
Package Part Number Temperature Range N TL074M/AM/BM TL074I/AI/BI TL074C/AC/BC Example : TL074IN -55C, +125C -40C, +105C 0C, +70 C D
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT)
Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + +
14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3
March 2001
1/11
SCHEMATIC DIAGRAM
VCC
1 0 0
2 0 0
Output
1 0 0
1/4 TL074
30k
8.2k
1.3k
VCC
35k
1.3k
35k
1 0 0
Parameter Supply voltage - note Input Voltage - note Power Dissipation Output Short-circuit Duration - note Storage Temperature Range
4) 2) 1)
TL074M, AM, BM
TL074I, AI, BI
TL074C, AC, BC
Unit V V V mW
C C
All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC + and VCC -. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded
2/11
13
DV io Iio
Input Offset Voltage Drift Input Offset Current - note Tamb = +25 C Tmin T amb T max Input Bias Current -note 1 Tamb = +25C Tmin Tamb Tmax Large Signal Voltage Gain (R L = 2k, Vo = 10V) Tamb = +25C Tmin Tamb Tmax Supply Voltage Rejection Ratio (RS = 50) Tamb = +25C Tmin T amb Tmax Supply Current, no load, per amplifier Tamb = +25 C Tmin T amb T max Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50) Tamb = +25C T min Tamb Tmax Output Short-circuit Current Tamb = +25C Tmin Tamb Tmax Output Voltage Swing Tamb = +25 C Tmin T amb T max RL = 2k RL = 10k RL = 2k RL = 10k 11 50 25 80 80
1)
10 5 100 10 200 20
V/C pA nA pA nA V/mV
Iib
20
30
Avd
200
200 dB
SVR
86
86 mA
2.5 2.5 V dB
80 80 10 10 10 12 10 12 8
70 70 60 60 10 10 10 12 10 12 8
mA 40 40 60 60 V 12 13.5 12 13.5
Ios
Vopp
SR tr Kov GBP Ri
Slew Rate (Tamb = +25C) Vin = 10V, RL = 2k, CL = 100pF, unity gain Rise Time (Tamb = +25 C) Vin = 20mV, RL = 2k , C L = 100pF, unity gain Overshoot (Tamb = +25C) Vin = 20mV, RL = 2k , C L = 100pF, unity gain Gain Bandwidth Product (Tamb = +25 C) Vin = 10mV, R L = 2k, CL = 100pF, f= 100kHz Input Resistance
3/11
Symbol
Parameter Total Harmonic Distortion (Tamb = +25 C) f= 1kHz, R L = 2k,CL = 100pF, A v = 20dB, Vo = 2V pp Equivalent Input Noise Voltage R S = 100, f = 1KHz
THD
0.01
0.01 nV ---------Hz
degrees
en m
15 45 120
15 45 120
dB
The input bias currents are junction leakage currents which approximately double for every 10C increase in the junction temperature.
4/11
30 25
RL = 10 k Tamb = +25 C
20
15 10
5
0 2
4 6 8 10 12 SUPPLY VOLTAGE ( V)
14
16
5/11
15V 10V
0.1
= 2k
0.01 -50
-25
25
50
75
100
125
-50
TEMPERATURE (C)
TEMPERATURE (C)
LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT versus FREQUENCY
180
100
PHASE SHIFT (right s ca le)
10
1 100
90
75
100
125
TEMPERATURE (C)
2.0
COMMON MODE MODE REJECTION RATIO (dB)
89
1.8 SUPPLY CURRENT (mA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50
V CC = No signal No load
15V
88 87 86 85 84 83 -75
R L = 10 k V C C= 15V
75
100
125
-50
-25
25
50
75
100
125
TEMPERATURE ( C)
TEMPERATURE (C)
6/11
6
OUTPUT VOLTAGE (mV)
28 24
4 2 0 -2 -4 -6 0
OUTPUT INPUT
OVERSHOOT
20 16 12 8 4
10%
90%
R L = 2k t Tamb = +25C
r
CC
= 15V
0.5
1.5
2.5
3.5
0.5
0.6
0.7
TIME (s )
TIME ( s)
70 60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 40 30 20 10 0 10 40 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz)
15V
= 10
400
1k
4k
10k
40k
100k
FREQUENCY (Hz)
7/11
10k 1k
eI
1/4
TL074 RL
eo
CL = 100pF
1/4
1M
T L074
Output A
1 F Input 100k
1/4
T L074
1/4
TL074
Output B
100k 100k
V CC+ -
1OO F
100k
1/4
T L074
Output C
8/11
16 k
22 0p F 2 20 pF
16 k
43 k 43 k Input
22 0p F
43 k 30k 43 k
22 0p F
30 k -
1/4
TL 07 4
43 k
1/4
TL 07 4
43 k
1/4
TL 07 4
1/4
TL 07 4
1.5 k
1 .5 k
Output B
Ground Output A
OUTPUT A
OUTPUT B
9/11
Millimeters Dim. Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055
Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100
10/11
L C
G c1
a2 b e3 D M e
s E
14 1
8 7 F
Millimeters Dim. Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45 (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007
a1
Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom http://www.st.com
b1
11/11
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.