Professional Documents
Culture Documents
Louvers Catalog
Louvers Catalog
J a n u a r y 2 0 0 6 B-1.0
www.ehpricesales.com
Extruded Aluminum
Selecting the Right Louver. ...................................... EG2 - EG3 Field Measurement Information. ............................. EG4 - EG9 How to use the Price Nomographs...................... EG10 - EG11
A B
F E
G Y
A C G H
B F DL
DR
WT B HL 90 A HR
LOUVERS
WB
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-1
First consideration:
FREE AREA The minimum area through which air can pass within a louver is called the free area of a louver1. The free area of a louver is critical to its overall performance and must be considered during its selection process. The free area has a direct effect on the air velocity though the louver: less free area creates higher air velocities thus a higher pressure drop. For intake conditions, higher air velocities equal higher water penetration. Everything being relative, this is true for all types and models of louvers. Whenever free area percentages are used always state the louver size on which it was calculated. (Published free area data is based on 48 X 48 louver) Although it is evident that free area varies with louver size, when a louver is selected for a low height application, the free area drops much faster than expected. This effect is most drastic as
the louver height approaches 3 to 4 times the louver depth. Since the head and sill of a louver are of a xed height, the space they occupy becomes important, thus reducing considerably the amount of available blade face area (and thus free area). As an example, a 48 x 48 x 4 deep louver may have 8.8 sq.ft. of free area (55%), a 48 x 12 of the same model would have 1.5 sq.ft. (37%). As a general rule, avoid selecting a louver when its height is less than 4 times its depth. The actual free area should always be checked when designing a louver below 48 in height. When the louver height exceeds 48, the percentage of free area will increase slightly.
LOUVERS
EG-
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Third consideration:
PRESSURE DROP The sizing of a louver for a desired pressure drop and air ow rate is greatly simplified with the unique PRICE NOMOGRAPHS: refer to the appropriate sheet and How to use PRICE NOMOGRAPHS for details (see page AA-11).They also permit quick selection based on free area and airow rate or louver dimensions and free area velocity or any other combination of parameters as a starting point. PRICE NOMOGRAPHS have been prepared for xed blade, adjustable blade and acoustic louvers and penthouses. When installing a damper behind a xed louver, the total pressure drop can be unpredictable. Use a louver with an integrated damper (combination louver) which is built as a single unit, the performance is tested and predictable. The pressure drop curves of louvers are based on free area velocity and vary very little, depending almost exclusively on the shape of the air passage between the blades. Screens can add a pressure drop increase of up to 10%. Fine mesh screens (insect screens) should always be made easily removable and installed only during critical periods.They must be cleaned regularly to remove dirt and debris.
WIND LOADS and STRUCTURAL ELEMENTS As a standard, all PRICE louvers built in a single section are designed to support a 25 psf (100 mph) wind load. All louvers having 2 sections in width by 2 sections in height or more may require additional structure to support the wind load. Louvers greater than 72 in width by 2 sections in height or more may require additional structure to support the wind load. Splice angles used to join sections in height are for alignment purposes only and cannot be considered structural elements. Since louver blades are welded to the jambs, securing a louver section by its jambs and central blade support, (if used) is considered acceptable practice.
Fourth consideration:
General Selection Guidelines Note for louvers in multiple sections: Louvers built in multiple sections are designed with provisions for thermal expansion and when installed, should never be butted together. When the temperature varies between -35C to 40C, the thermal expansion of a 10 ft [3m] aluminium louver is almost [6mm] (steel louvers expand half this amount).
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-
LOUVERS
LEFT
RIGHT
W BOTTOM
Step #3a: Measure the opening width and height on all 4 sides.
and approved submittal drawings to fully understand how the louvers are intended to be installed on the project, how they are to t in the openings and how they are to be attached in those openings.
opening measurements. Prepare a sketch of each louver viewed from the exterior and identify its location.
LEFT SIDE
BOW
BOTTOM BOW
Step #3c: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rectify it if possible. For those that cannot be rectied, record them on your sketch.
LOUVERS
EG-
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
D H
BOW
90
W BOW
Step #4a: Measure the opening width, height and diagonal side. Based on these dimensions, louver dimensions will be corrected to obtain 90 between width and height.
Step #4b: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rectify if possible. For those that cannot be rectied, record them on your sketch.
BOW
Step #5b: Use a string to see if the sides of the opening bows in or out. If an inward bow is detected, rectify if possible. For those that cannot be rectied, record them on your sketch.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-5
LOUVERS
Exterior Elevations
F G
A B C
E
B H
C D I
For openings of 72" [1829] or less. Step #6a: If the circular opening is relatively small and has a consistent circumference, you can measure the diameter in 3 or 4 locations and record the smallest dimension. For larger or irregular openings, mark the circular opening in 6 approximately equidistant points on the edge of the opening. Measure the distances A, B, C and the actual distances D through I. By the use of computer assisted drafting (CAD), a true circle will be tted to the actual opening.
For openings larger than 72" [1829]. Note: Dimensions D through I should be approximately equal to the radius of the circle.
Exterior Elevations
D E B
E
A
A C G H
B F
C G H F
W
LOUVERS
Step #6b: Mark the circular portion of the opening in 4 approximately equidistant points on its edge opening. Measure the distances A, B, G, H, W and the actual distances C through F . By the use of computer assisted drafting (CAD), a true circular portion will be fitted to the actual opening.
Step #6c: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectied, record it on your sketch.
EG-6
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
DL
DR
WT B HL 90 A HR
A HR
HL B 90
WB
DT HR A B
HL
B HR
HL DB
D
Step #7a: Divide opening into rectangles and triangles and treat as in Steps #3a through 5b. Based on these dimensions, louver dimensions will be corrected to obtain parallel sides and/or 90 between width and height.
Step #7b: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectied, record it on your sketch.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-7
LOUVERS
Y C
F
X B
G Y
Step #8a: After measuring the 3 sides of the opening, draw a horizontal line to establish the blade orientation and measure distance X and Y.
Step #8b: M e a s u r e t h e d i s t a n c e s A t h r o u g h E . Divide shape into simple triangular shapes and measure the remaining distances F and G. Draw a horizontal line to establish the blade orientation and measure distances X and Y. Step #8c: Use a string to see if the base of the opening bows in or out. If an inward bow is detected, rectify it if possible. If it cannot be rectied, record it on your sketch.
Large shapes divided into sections When a louver shape is divided into sections by visible mullions or when various louver shapes are interdependent and if the blades must line up in the nal assembly, always include a sketch of the relative positions of the individual shapes.
LOUVERS
Section A
X
Section B
Y
Section C
EG-8
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Louver Flanges
Although anges of various widths are available, the most common flange is 1(38mm). The ange width is dened as the width that exceeds the louver frame. Thus, the overall size of a louver with 1 anges to t a 48" x 48" opening would be 50 by 50 and would exceed the opening by 1 . 48" x 48" opening less undersizing (2 x ) = 47 x 47 louver with anges added (2 x 1) = 50 x 50 overall
Structural Support
When the louver comes in several sections, structural supports must be provided to securely attach these sections to the building. In most cases, these structural elements are installed ahead of time by others and their exact location as installed must be veried to ensure that their location matches the louver submittal drawings. If required, changes can be made to relocate the mullions on the louvers before they are put into production with little or no cost. Here are other questions which may have to be addressed: Is there adequate space behind the louver to permit fastening from inside? Are there any structural or other elements that might interfere with the louver? Are the vertical edges of the opening sufciently rigid to attach the sides of the louver?
Standard Installation
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-
LOUVERS
Legend F
you need to know at least 3 of the following 6 variables: the louver width and height, the louver free area, the air volume, free area air velocity or static pressure loss. The possible starting point combinations are as follows: One louver dimension ow rate free area velocity One louver dimension ow rate pressure drop One louver dimension ow rate free area Two louver dimensions ow rate Two louver dimensions pressure drop Two louver dimensions free area velocity
P-V W A H
prised of 2 interrelated areas. The dimensional characteristics are on the left side of the sheet and the air ow characteristics are on the right. Drawing a line joining the Louver Width (W scale) to the Louver Height (H scale), you obtain the free area as the line crosses the Louver Free Area (A scale). You can also start with the free area and one dimension to obtain the 2nd dimension.
Louver Free Area (A scale) (obtained in step 2) to the Louver Air Flow (F scale), you obtain the free area velocity and pressure drop as the line crosses the Pressure drop / Free area velocity (P-V scale). The line can also be drawn with any combination of 2 starting points: [free area & pressure drop] or [ow rate & pressure drop] or [ow rate & free area velocity]. The PRICE Nomographs give you maximum exibility in the selection of your PRICE louvers. See the examples on the following page for more details.
W = Louver Width (inches) H = Louver Height (inches) A = Louver Free Area (Square feet) F = Air Flow (CFM) P-V = Static Pressure Drop (in. of Water) Free Area Air Velocity (FPM)
LOUVERS
EG-10
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
c). Draw a line joining 6,000 CFM on the Air Flow (F scale) to the free area you just found. d). Read the free area velocity and static pressure loss at the point where this second line meets the Pressure Drop/Free Area Velocity (P-V scale). ANSWER The free area air velocity is 600 FPM and louver static pressure loss is 0.06 .
2. The louver exhaust air volume is 6,000 CFM and expected static pressure loss is 0.06 . Louver height must be smaller or equal to 72 .What is the required free area and minimum louver width? a). Apply pressure drop correction factor for exhaust condition 0.06" 0.825 = 0.07" WG b). Draw a line joining 6,000 CFM on the Air Flow (F scale) to the calculated static pressure loss on the Pressure Drop/Free Air Velocity (P-V scale) and continuing to the Louver Free Area (A scale). c). Read the free area at the point where the line meets the Louver Free Area (A scale). ANSWERThe louver free area is 10.02 square feet.
LOUVERS
d). Draw a line joining the 72 high on the Louver Height (H scale) to the free area and continuing to the Louver Width (W scale). e). Read the required louver width. ANSWER The minimum louver width is 36.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
EG-11
Louvers
Index
Extruded Aluminum
JE443 ZE439 ZE445 DE439 DE635 NJE2 NSE1 QA645 QA1245 RSE5 MCJE443 MCZE439 MCZE445 MCDE439 MCDE635 BCJE443 BCZE439 BCZE445 BCDE439 BCDE635 Stationary Louvers................................................... L3 Stationary Louvers................................................... L4 Stationary Louvers................................................... L5 Stationary Drainable Louvers.................................. L6 Stationary Drainable Louvers.................................. L7 Stationary Louvers................................................... L8 Stationary Louvers................................................... L9 Stationary Acoustic Louvers................................. L10 Stationary Acoustic Louvers.................................. L11 Rain Storm Louvers............................................... L12 Miter Corner Penthouse Stationary Louvers....... L13 Miter Corner Penthouse Stationary Louvers....... L14 Miter Corner Penthouse Stationary Louvers....... L15 Miter Corner Penthouse Stationary Louvers....... L16 Miter Corner Penthouse Stationary Louvers....... L17 Box Corner Penthouse Drainable Louvers. ........... L18 Box Corner Penthouse Drainable Louvers. .......... L19 Box Corner Penthouse Drainable Louvers. .......... L20 Box Corner Penthouse Drainable Louvers. .......... L21 Box Corner Penthouse Drainable Louvers. .......... L22
Accessories ................................................................................. L23 Suggested Specications . ............................................ L24 - L31 Price / Airolite Cross Reference . ........................................... L32
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LOUVERS
Louvers
LOUVERS
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models Blade Louvers 43 J-Blade JE443
E.H. Price Limited certies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Price JE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a J blade prole in a 4 deep assembly with the blades positioned at a 43 angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rating Program. Features "J" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 50.6% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Performance Rating Standard Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o AMCA Standard 500 25 psf (100 mph) 8.1 sq.ft. (0.753 sq.m.) 50.6% 642 FPM (196 m/min) 5,200 CFM (147 m3/min) 0.07 H2O (18 Pa)
LOUVERS
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models
Blade Louvers 39 Z-Blade ZE439
E.H. Price Limited certies that the ZE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Price ZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 39 angle.The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rating Program. Features "Z" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 51.9% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
ZE439
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Performance Rating Standard Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o AMCA Standard 500 25 psf (100 mph) 8.31 sq.ft. (0.772 sq.m.) 51.9% 849 FPM (259 m/min) 7,059 CFM (200 m3/min) 0.12 H2O (29 Pa)
Visible Mullion Continuous Blade
LOUVERS
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models
Blade Louvers 45 Z-Blade ZE445
E.H. Price Limited certies that the ZE445 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Price ZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 45 angle. The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rating Program. Features "Z" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 49.5% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1, 1.5, 2, or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
ZE445
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Performance Rating Standard Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o AMCA Standard 500 25 psf (100 mph) 7.92 sq.ft. (0.736 sq.m.) 49.5% 669 FPM (204 m/min) 5,298 CFM (150 m3/min) 0.09 H2O (23 Pa)
LOUVERS
Continuous Blade
Visible Mullion
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models Blade Louvers 39 Blade DE439
E.H. Price Limited certies that the DE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Price DE439 stationary drainable louvers feature alloy 6063-T5 extruded 4 aluminum blades positioned at a 39 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rating Program. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 53.6% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
DE439
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Performance Rating Standard Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o AMCA Standard 500 25 psf (100 mph) 8.57 sq.ft. (0.796 sq.m.) 53.6% 886 FPM (270 m/min) 7,589 CFM (215 m3/min) 0.13 H2O (3 Pa)
LOUVERS
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models Blade Louvers 35 Blade DE635
E.H. Price Limited certies that the DE635 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Price DE635 stationary drainable louvers feature alloy 6063-T5 extruded 6 aluminum blades positioned at a 35 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Performances of louvers manufactured by Price are based on tests and procedures in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rating Program. Features Drainable Blade. Welded Construction. .081 Extruded Aluminum Blades and Frames. Nominal 55.9% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
DE635
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Performance Rating Standard Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o AMCA Standard 500L 25 psf (100 mph) 8.95 sq.ft. (0.831 sq.m.) 55.9% 1,041 FPM (317 m/min) 9,316 CFM (264 m3/min) 0.17 H2O (42 Pa)
LOUVERS
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models Blade Louvers 30 J-Blade NJE2
Price NJE2 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a J blade prole in a 2 deep assembly with the blades positioned at a 30 angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "J" Blade Prole. .064 Extruded Aluminum Blades and Frames. Nominal 44.1% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .064 (1.6 mm) .064 (1.6 mm) 2 (51 mm) 30o 25 psf (100 mph) 7.06 sq.ft. (0.656 sq.m.) 44.1% 380 FPM (116 m/min) 2,682 CFM (76 m3/min) 0.03 H2O (6 Pa)
2" (51)
Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
LOUVERS
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L26
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Product Information
Models Blade Louvers Straight Blade NSE1
Price NSE1 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a straight blade prole in a 1.5 deep assembly. This straight blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features .125 Extruded Aluminum Blades. Nominal 69.3% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .125 (3 mm) .064 (1.6 mm) 1.5 (38 mm) 29 25 psf (100 mph) 11.09 sq.ft. (1.03 sq.m.) 69.3% N/A
N/A
N/A
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L26
Copyright E.H. Price Limited 2010.
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LOUVERS
Price QA645 stationary louvers feature formed aluminum blades. The louver features an acoustic blade prole in a 6 deep assembly with the blades positioned at a 45 angle. This acoustic blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Acoustic Blade. .081 Formed Aluminum Blades and Frames. Nominal 28.5% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process. Acoustic performance ratings are determined with ASTM Designations E90-97 "Recommended Practice for Laboratory Measurement at Airborne Sound Transmission Loss at Building Partitions", and E413 3-87 "Standard Classication for Determination of Sound Transmission Loss Class".
Free-Field Noise Reduction In Decibels Selected 1/3 Octave Bands Center Frequency (Hz) 63 13 125 8 250 10 500 13 1,000 21 2,000 25 4,000 22 8,000 23
Louver Type Material Stationary Blade Perforated Liner Frame Louver Depth Blade Angle Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .032 (8 mm) .081 (2 mm) 6 (152 mm) 45o 25 psf (100 mph) 4.56 sq.ft. (0.424 sq.m.) 28.5% 780 FPM (238 m/min) 3,555 CFM (101 m3/min) 0.06 H2O (16 Pa)
LOUVERS
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L26
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
10
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price QA1245 stationary louvers feature formed aluminum blades. The louver features an acoustic blade prole in a 12 deep assembly with the blades positioned at a 45 angle. This acoustic blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Acoustic Blade. .081 Extruded Aluminum Blades and Frames. Nominal 24.9 % free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process. Acoustic performance ratings are determined with ASTM Designations E90-97 "Recommended Practice for Laboratory Measurement at Airborne Sound Transmission Loss at Building Partitions", and E413 3-87 "Standard Classication for Determination of Sound Transmission Loss Class".
Product Information Index Accessories................................................L23 Suggested Specication...........................L27
Copyright E.H. Price Limited 2010.
Free-Field Noise Reduction In Decibels Selected 1/3 Octave Bands Center Frequency (Hz) 63 16 125 13 250 15 500 18 1,000 16 2,000 18 4,000 18 8,000 21
Louver Type Material Stationary Blade Perforated Liner Frame Louver Depth Blade Angle Wind Load Free Area 4 x 4 Unit Percent Free Area Free Area Velocity at Beginning Point of Water Penetration (1) Air Volume Delivered at Beginning Point of Water Penetration (1) Pressure Drop at Beginning Point of Water Penetration (1)
Ratings do not include the effect of a bird screen.
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .032 (8 mm) .081 (2 mm) 12 (102 mm) 45o 25 psf (100 mph) 3.981 sq.ft. (0.369 sq.m.) 24.9% 1046 FPM (319 m/min) 4,160 CFM (118 m3/min) 0.13 H2O (32 Pa)
LOUVERS
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass through a 4' x 4' louver during a 15 minute test.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
11
Product Information
Models
Blade Louvers 39 Blade RSE5
Price RSE5 stationary drainable louvers feature alloy 6063-T5 extruded aluminum. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream. This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 57% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Continuous Blade Sections (invisible mullions). Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
RSE5
Louver Type: Material: Front Blade: Back Blade: Frame: Louver Depth: Water Penetration Test: % Free Area: Free Area 4' x 4' Unit: Ext Wind Velocity: Rainfall Rate: Effectiveness Ratio:
Ratings do not include the effect of a bird screen.
Storm Class Extruded Aluminum (Alloy 6063-T5) 0.081" (2.06mm) N/A 0.081" (2.06mm) 5" (127.0mm) Simulated Rain 38.5% 6.16 sq. ft. (0.572 sq m) 29.1 mph (13 m/s) 2.95"/H (75 ml/H) 99.73%
LOUVERS
12
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price MCJE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a J blade prole in a 4 deep assembly with the blades positioned at a 43 angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "J" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 50.6% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Continuous Blade Sections (invisible mullions). Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4 x 4 x 50.625" Unit Percent Free Area
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o 25 psf (100 mph) 28.00 sq.ft. (2.601 sq.m.) 41.5%
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L28
Copyright E.H. Price Limited 2010. All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
13
Price MCZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 39 angle.The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "J" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 49.1% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Continuous Blade Sections (invisible mullions). Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
LOUVERS
MCZE439
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 48 x 48 x 49.438 Unit Percent Free Area
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 32.35 sq.ft. (3.005 sq.m.) 49.1%
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Inside Curb Dimension
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L28
14
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price MCZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 45 angle.The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "Z" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 40.8% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Continuous Blade Sections (invisible mullions). Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load
MCZE445
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o 25 psf (100 mph) 27.51 sq.ft. (2.556 sq.m.) 40.8%
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Inside Curb Dimension
LOUVERS
15
Price MCDE439 stationary drainable louvers feature alloy 6063-T5 extruded 4 aluminum blades positioned at a 39 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream.This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 49.1% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Continuous Blade Sections (invisible mullions). Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load
MCDE439
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 32.35 sq.ft. (3.005 sq.m.) 49.1%
6" (152)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Curb Inside Curb Dimension
LOUVERS
16
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price MCDE635 stationary drainable louvers feature alloy 6063-T5 extruded 6 aluminum blades positioned at a 35 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream.This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 49.2% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Continuous Blade Sections (invisible mullions). Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load
MCDE635
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o 25 psf (100 mph) 32.97 sq.ft. (3.063 sq.m.) 49.2%
Penthouse Height
4" (102)
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 16" (406)) Inside Curb Dimension
LOUVERS
17
Price BCJE443 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a J blade prole in a 4 deep assembly with the blades positioned at a 43 angle. This J-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "J" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 49.4% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4" x 4" x 4" Unit Percent Free Area
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o 25 psf (100 mph) 31.59 sq.ft. (2.935 sq.m.) 49.4%
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362) Outside Penthouse Dimension (Inside Curb Dim. + 8" (203))
Curb
Product Information Index Accessories................................................ L10 Accessories................................................L23 Specication........................... L11 Suggested Specication...........................L30
18
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price BCZE439 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 39 angle.The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "Z" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 55.3% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
BCZE439
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4" x 4" x 4" Unit Percent Free Area
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 35.40 sq.ft. (3.29 sq.m.) 55.3%
19
LOUVERS
Price BCZE445 stationary louvers feature alloy 6063-T5 extruded aluminum blades. The louver features a Z blade prole in a 4 deep assembly with the blades positioned at a 45 angle.The drainable head and jambs enable the louver to achieve optimum air performance and water penetration ratings. This Z-blade louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features "Z" Blade Prole. .081 Extruded Aluminum Blades and Frames. Nominal 49.8% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
BCZE445
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4" x 4" x 4" Unit Percent Free Area
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o 25 psf (100 mph) 31.84 sq.ft. (2.96 sq.m.) 49.8%
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362) Outside Penthouse Dimension (Inside Curb Dim. + 8" (203))
Curb
20
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Price BCDE439 stationary drainable louvers feature alloy 6063-T5 extruded 4 aluminum blades positioned at a 39 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream.This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 55.3% free area (based on 48 x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
BCDE439
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4" x 4" x 4" Unit Percent Free Area
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 35.40 sq.ft. (3.289 sq.m.) 55.3%
21
LOUVERS
Price BCDE635 stationary drainable louvers feature alloy 6063-T5 extruded 6 aluminum blades positioned at a 35 angle. The drainable louvers achieve optimum air performance and water penetration ratings with vertical and horizontal gutter systems that capture droplets before they cascade from blade to blade and are entrained in the airstream.This louver is available with visible mullions that are joined with an extruded aluminum I connection, or continuous horizontal blades that utilize concealed blade braces and hidden vertical supports in place of jamb frames to present uninterrupted horizontal blade appearance. Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 57.5% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame. Mill nish. Options Welded Construction. Extended Sill (loose) 14 GA. Aluminum. Blank-offs are available in Aluminum with or without Insulation. Insulation is available in 1 , 1.5 , 2 , or 3 thickness. Variety of Mounting options. Exterior or Interior Frame Mounting. Variety of Bird Screens, Insect Screens and Frames available. Wide variety of Finishes: Baked Enamel, Prime Coat, Custom Finishes, Clear Anodized and Colour Anodized. Select from PRICE Colour Chart or provide colour sample to match. Note: Colour variations can be expected within the same order and even on the same louver due to the anodizing process.
BCDE635
Louver Type Material Stationary Blade Frame Louver Depth Blade Angle Wind Load Free Area 4" x 4" x 4" Unit Percent Free Area
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o 25 psf (100 mph) 36.83 sq.ft. (3.422 sq.m.) 57.5%
6" (152)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Curb Dim. + 8" (203)) Curb Mounting Straps Curb Inside Curb Dimension
22
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Accessories
Louver Accessories
Bird Screen Insect Screen
Bird screens are (12.7mm), (19.1mm) or 1: (25.4mm) mesh, 0.063 (1.60mm) diameter screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screens are available in expanded aluminum and expanded aluminum with frame construction. Gauges available 051, 16 and 19 ga. Available for interior or exterior mounting.
Insect screens are 18 x 16 (1.4 x 1.6 mm) mesh, 0.012" (0.30mm) diameter screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screens are available in aluminum or bronze construction. Gauges available - 051, 16 and 19 ga. Available for interior or exterior mounting.
Blank-offs
The extruded polystyrene insulation is factory mounted with panel screws. Aluminum blank-off panels available with or without insulation Insulated blank-off panels available in 1, 1-, 2 and 3 insulation thickness. Gauges available 14 and 18 ga. (Aluminum construction only)
Loose sill is available in 4 to 10 widths in 14-gauge aluminum construction. For single sections, the length of the sill must be equal to the opening width, with a maximum section length of 120 (3048mm). For multiple sections, the minimum recommended overlap is 6 (152mm) with a sealant in between (minimum bead).
LOUVERS
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
23
Suggested Specication
Louvers
JE443 J-Blade Stationary Louver Furnish and install PRICE Model JE443 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 43-degree stationary J prole blades. Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certied Rating Program. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. ZE439 Z-Blade Stationary Louver Furnish and install PRICE Model ZE439 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary Z prole blades. Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certied Rating Program. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. ZE445 Z-Blade Stationary Louver Furnish and install PRICE Model JE445 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 45-degree stationary Z prole blades. Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certied Rating Program. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions.
LOUVERS
24
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Suggested Specication
Louvers
Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. DE439 Drainable Louver Furnish and install PRICE Model DE439 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary drainable blades. Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certied Rating Program. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for
Copyright E.H. Price Limited 2010.
{specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name). Options Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. DE635 Drainable Louver Furnish and install PRICE Model DE635 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 6 (152.4mm) deep with 35-degree stationary drainable blades. Louver performance shall be based on tests and procedures in accordance with AMCA publication 511 and comply with the requirements of the AMCA Certied Rating Program. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load.
Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions.
LOUVERS
Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
25
Suggested Specication
Louvers
NJE2 J-Blade Stationary Louver Furnish and install PRICE Model NSE2 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 2 (51.6mm) deep with 30-degree stationary J prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame.
LOUVERS
Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. NCE1 Straight Blade Stationary Louver Furnish and install PRICE Model NCE1 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 1.5 (38.1mm) deep with stationary straight prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable
U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. QA645 Acoustic Blade Stationary Louver Furnish and install PRICE Model QA645 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of formed aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 6 (152mm) deep with 45-degree stationary acoustic prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and finished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen
Copyright E.H. Price Limited 2010.
26
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Suggested Specication
Louvers
in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. QA1245 Acoustic Blade Stationary Louver Furnish and install PRICE Model QA1245 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of formed aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 12 (305mm) deep with 45-degree stationary acoustic prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum
Copyright E.H. Price Limited 2010.
thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. RSE5 Drainable Louver Furnish and install PRICE Model RSE5 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 5 (127mm) deep with stationary drainable blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish.
98. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel.
Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 611All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
27
LOUVERS
Suggested Specication
Louvers
MCJE443 J-Blade Miter Corner Penthouse Louver Furnish and install PRICE Model MCJE443 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 43-degree stationary J prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame.
LOUVERS
Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. MCZE439 Z-Blade Miter Corner Penthouse Louver Furnish and install PRICE Model MCZE439 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary Z prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable
U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. MCZE445 Z-Blade Miter Corner Penthouse Louver Furnish and install PRICE Model MCZE445 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 45-degree stationary Z prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen
Copyright E.H. Price Limited 2010.
28
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Suggested Specication
Louvers
in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. MCDE439 Drainable Blade Miter Corner Penthouse Louver Furnish and install PRICE Model MCDE439 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary drainable blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 611 Copyright E.H. Price Limited 2010.
98. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. MCDE635 Drainable Blade Miter Corner Penthouse Louver Furnish and install PRICE Model MCDE635 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 6 (152.4mm) deep with 35-degree stationary drainable blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting.
Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel.
If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
29
LOUVERS
Suggested Specication
Louvers
BCJE443 J-Blade Box Corner Penthouse Louver Furnish and install PRICE Model BCJE443 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 43-degree stationary J prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame.
LOUVERS
Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. BCZE439 Z-Blade Box Corner Penthouse Louver Furnish and install PRICE Model BCZE439 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary Z prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter
aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. BCZE445 Z-Blade Box Corner Penthouse Louver Furnish and install PRICE Model BCZE445 Architectural Blade Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 45-degree stationary Z prole blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen
Copyright E.H. Price Limited 2010.
30
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Suggested Specication
Louvers
in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. BCDE439 Drainable Blade Box Corner Penthouse Louver Furnish and install PRICE Model DE439 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 4 (101.6mm) deep with 39-degree stationary drainable blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Louvers shall be supplied with a standard mill nish. If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions. Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 611 Copyright E.H. Price Limited 2010.
98. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil. Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel. BCDE635 Drainable Blade Box Corner Penthouse Louver Furnish and install PRICE Model DE635 Drainable Louver of size and shape indicated on the plans and/or as described in schedules. Louvers shall be constructed entirely of extruded aluminum, alloy 6063-T5. Blades and frames shall be minimum 0.081 (2.06mm) wall thickness. Louver assemblies shall be 6 (152.4mm) deep with 35-degree stationary drainable blades. Louvers shall be designed to withstand a 25 psf (100 mph wind equivalent) wind load. Each louver shall be tted with 1/2" (12.7mm) mesh x 0.063" (1.60mm) diameter aluminum bird screen. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting.
Louvers shall receive a Class 2 (clear) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.4 - 0.7 mil. Louvers shall receive a Class 1 (colour) anodize nish complying with AAMA 61198. Finish is applied to chemically etched and pretreated aluminum to a minimum thickness of 0.7 - 1.0 mil.Colour shall be Price (specify colour name). Options Each louver shall be tted with {select required mesh size: 1/2 (12.7mm), 3/4 (19.1mm) or 1 (25.4mm)} mesh x 0.063 (1.60mm) diameter aluminum bird screen in non-rewirable U-shaped frames for permanently securing screen mesh. Bird screen shall be expanded aluminum construction and suitable for {specify: interior or exterior} mounting. Each louver shall be tted with 18 x 16 (1.4 x 1.6mm) mesh, 0.012 (0.03mm) diameter aluminum insect screen in non-rewirable U-shaped frames for permanently securing screen mesh. Insect screen shall be suitable for {specify: interior or exterior} mounting. Louvers shall be welded construction. Louvers shall be supplied with a anged frame. Louvers shall be supplied with continuous blade section to give the appearance of invisible mullions. Each louver shall be tted with an (insulated or non-insulated) aluminum blank-off panel.
If an optional nish is required, please select one of the following: Louvers shall be factory primed and nished-after-assembly with a baked enamel resin coating in a colour selected from the colour chart. Primer and resin coating shall be oven baked at 450F in accordance with the coating manufacturers instructions.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
31
LOUVERS
Louvers
LOUVERS
32
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Extruded Aluminum
How to use the Price Nomographs ....................................................................................................... LP2 - LP3 JE443 Stationary Louvers................................................................................................................... LP4 ZE439 Stationary Louvers................................................................................................................... LP6 ZE445 Stationary Louvers................................................................................................................... LP8 DE439 Stationary Drainable Louvers. .............................................................................................. LP10 DE635 Stationary Drainable Louvers. .............................................................................................. LP12 NJE2 Stationary Louvers................................................................................................................ LP14 NSE1 Stationary Louvers................................................................................................................ LP16 QA645 Stationary Acoustic Louvers. ................................................................................................ LP18 QA1245 Stationary Acoustic Louvers. ................................................................................................ LP20 RSE5 Rain Storm Louvers.............................................................................................................. LP22 MCJE443 Miter Corner Penthouse Stationary Louvers. ...................................................................... LP24 MCZE439 Miter Corner Penthouse Stationary Louvers. ...................................................................... LP26 MCZE445 Miter Corner Penthouse Stationary Louvers. ...................................................................... LP28 MCDE439 Miter Corner Penthouse Drainable Louvers. ....................................................................... LP30 MCDE635 Miter Corner Penthouse Drainable Louvers. ....................................................................... LP32 BCJE443 Box Corner Penthouse Stationary Louvers......................................................................... LP34 BCZE439 Box Corner Penthouse Stationary Louvers......................................................................... LP36 BCZE445 Box Corner Penthouse Stationary Louvers......................................................................... LP48 BCDE439 Box Corner Penthouse Drainable Louvers.......................................................................... LP40 BCDE635 Box Corner Penthouse Drainable Louvers.......................................................................... LP42
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-1
lOUVERS
you need to know at least 3 of the following 6 variables: the louver width and height, the louver free area, the air volume, free area air velocity or static pressure loss. The possible starting point combinations are as follows: One louver dimension ow rate free area velocity One louver dimension ow rate - pressure drop One louver dimension ow rate free area Two louver dimensions ow rate Two louver dimensions pressure drop Two louver dimensions free area velocity
prised of 2 interrelated areas. The dimensional characteristics are on the left side of the sheet and the air ow characteristics are on the right. Drawing a line joining the Louver Width ( W scale) to the Louver Height ( H scale), you obtain the free area as the line crosses the Louver Free Area (A scale). You can also start with the free area and one dimension to obtain the 2nd dimension.
LP-2
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-3
lOUVERS
E.H. Price Limited certies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-4
lOUVERS
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o AMCA Standard 500 25 psf (100 mph) 8.1 sq.ft. (0.753 sq.m.) 50.6% 642 FPM (196 m/min) 5,200 CFM (147 m3/min) 0.07 H2O (18 Pa)
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features Storm proof blade with rain check. All welded construction: minimum 1 llet welds. Available in continuous blade construction (CB models). Nominal 51% free area (based on 48 x 48). Integral perimeter caulking stop. Optional integral 1.5 anges. Other sizes available as add-ons. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-5
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
E.H. Price Limited certies that the ZE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-6
lOUVERS
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o AMCA Standard 500 25 psf (100 mph) 8.31 sq.ft. (0.772 sq.m.) 51.9% 849 FPM (259 m/min) 7,059 CFM (200 m3/min) 0.12 H2O (29 Pa)
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features High performance louver with drainable frame. All welded construction: minimum 1 llet welds. Available in continuous blade construction (CB models). Nominal 52% free area (based on 48 x 48). Integral perimeter caulking stop. Optional integral 1.5 anges. Other sizes available as add-ons. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
Continuous Blade
ALL-WELDED CONSTRUCTION
LOUVERS
Visible Mullion
LP-7
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
E.H. Price Limited certies that the ZE445 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-8
lOUVERS
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o AMCA Standard 500 25 psf (100 mph) 7.92 sq.ft. (0.736 sq.m.) 49.5% 669 FPM (204 m/min) 5,298 CFM (150 m3/min) 0.09 H2O (23 Pa)
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features All welded construction: minimum 1 llet welds. Available in continuous blade construction (CB models). Nominal 50% free area (based on 48 x 48). Integral perimeter caulking stop. Optional integral 1.5 anges. Other sizes available as add-ons. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-9
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
E.H. Price Limited certies that the DE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-10
lOUVERS
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o AMCA Standard 500 25 psf (100 mph) 8.57 sq.ft. (0.796 sq.m.) 53.6% 886 FPM (270 m/min) 7,589 CFM (215 m3/min) 0.13 H2O (3 Pa)
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features Drainable blade with vertical jamb gutter. All welded construction: minimum 1 llet welds. Available in continuous blade construction (CB models). Nominal 54% free area (based on 48 x 48). Integral perimeter caulking stop. Optional integral 1.5 anges. Other sizes available as add-ons. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-11
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
E.H. Price Limited certies that the DE635 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Rateings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-12
lOUVERS
Visible Mullion or Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o AMCA Standard 500 25 psf (100 mph) 8.95 sq.ft. (0.831 sq.m.) 55.9% 1,233 FPM (375 m/min) 11,041 CFM (313 m3/min) 0.23 H2O (57 Pa)
(1) Beginning point of water penetration is dened by AMCA standard 511 as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features Drainable blade with vertical jamb gutter. All welded construction: minimum 1 llet welds. Available in continuous blade construction (CB models). Nominal 56% free area (based on 48 x 48). Integral perimeter caulking stop. Optional integral 1.5 anges. Other sizes available as add-ons. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-13
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-14
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .064 (1.6 mm) .064 (1.6 mm) 2 (51 mm) 30o 25 psf (100 mph) 7.06 sq.ft. (0.656 sq.m.) 44.1% 380 FPM (116 m/min) 2,682 CFM (76 m3/min) 0.03 H2O (6 Pa)
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test.
2" (51)
Features Storm proof blade with rain check. All welded construction: minimum 1 llet welds. Nominal 44% free area (based on 48 x 48). Optional anges up to 4 available. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-15
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-16
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .125 (3 mm) .064 (1.6 mm) 1.5 (38 mm) 29 25 psf (100 mph) 11.09 sq.ft. (1.03 sq.m.) 69.3% N/A
N/A
N/A
Features Nominal 69% free area (based on 48 x 48). Optional anges up to 4 available. Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-17
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-18
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .032 (8 mm) .081 (2 mm) 6 (152 mm) 45o 25 psf (100 mph) 4.56 sq.ft. (0.424 sq.m.) 28.5% 780 FPM (238 m/min) 3,555 CFM (101 m3/min) 0.06 H2O (16 Pa)
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test. Features All welded construction: minimum 1 llet welds. Available in continuous blade construction (FCB models). Nominal 29% free area (based on 48 x 48). Optional integral anges up to 4 . Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color. Louvers manufactured by E.H. Price are eligible to bear the Air Movement and Control Association (AMCA) certied rating seals for air performance and water penetration of their equivalent Airolite models where applicable.
ALL-WELDED CONSTRUCTION
LOUVERS
Acoustic performance ratings are determined with ASTM Designations E90-97 "Recommended Practice for Laboratory Measurement at Airborne Sound Transmission Loss at Building Partitions", and E413 3-87 "Standard Classication for Determination of Sound Transmission Loss Class".
LP-19
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-20
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .032 (8 mm) .081 (2 mm) 12 (102 mm) 45o 25 psf (100 mph) 3.981 sq.ft. (0.369 sq.m.) 24.9% 1046 FPM (319 m/min) 4,160 CFM (118 m3/min) 0.13 H2O (32 Pa)
(1) Beginning point of water penetration is dened as the free area velocity at which 0.01 ounces of water per square foot of free area is measured to pass througha 4' x 4' louver during a 15 minute test.
Free-Field Noise Reduction In Decibels Selected 1/3 Octave Bands Center Frequency (Hz) 63 16 125 13 250 15 500 18 1,000 16 2,000 18 4,000 18 8,000 21
Features All welded construction: minimum 1 llet welds. Available in continuous blade construction (FCB models). Nominal 25% free area (based on 48 x 48). Optional integral anges up to 4 . Optional bird and insect screens available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color. Acoustic performance ratings are determined with ASTM Designations E90-97 "Recommended Practice for Laboratory Measurement at Airborne Sound Transmission Loss at Building Partitions", and E413 3-87 "Standard Classication for Determination of Sound Transmission Loss Class".
ALL-WELDED CONSTRUCTION
LOUVERS
LP-21
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-22
lOUVERS
Storm Class Extruded Aluminum (Alloy 6063-T5) 0.081" (2.06mm) N/A 0.081" (2.06mm) 5" (127.0mm) Simulated Rain 38.5% 6.16 sq. ft. (0.572 sq m) 29.1 mph (13 m/s) 2.95"/H (75 ml/H) 99.73%
Features Drainable Blade. .081 Extruded Aluminum Blades and Frames. Nominal 39% free area (based on 48x 48). Integral perimeter caulking stop. 1/2" x 1/2" (12 x 12) 16 gauge Expanded Aluminum Bird Screen without frame Mill nish.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-23
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-24
lOUVERS
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o 25 psf (100 mph) 28.00 sq.ft. (2.601 sq.m.) 41.5%
Features Storm proof blade with rain check. Unique bolted conrer design affords excellent alignment of adjoining louver Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 42% free area (based on 48 x 48 x 50.625"). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
ALL-WELDED CONSTRUCTION
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Curb Inside Curb Dimension
LOUVERS
LP-25
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-26
lOUVERS
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 32.35 sq.ft. (3.005 sq.m.) 49.1%
Features Unique bolted conrer design affords excellent alignment of adjoining louver. Drain holes at top blade corners. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 49% free area (based on 48 x 48 x 49.438"). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Curb Inside Curb Dimension
ALL-WELDED CONSTRUCTION
LOUVERS
LP-27
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-28
lOUVERS
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o 25 psf (100 mph) 27.51 sq.ft. (2.556 sq.m.) 40.8%
Features Unique bolted conrer design affords excellent alignment of adjoining louver. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 41% free area (based on 48 x 48 x 50.625"). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Curb Inside Curb Dimension
ALL-WELDED CONSTRUCTION
LOUVERS
LP-29
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-30
lOUVERS
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 32.35 sq.ft. (3.005 sq.m.) 49.1%
Features Unique bolted conrer design affords excellent alignment of adjoining louver. Drainable blades with drain holes at corners. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 49% free area (based on 48 x 48 x 49.438"). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
6" (152)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
ALL-WELDED CONSTRUCTION
Outside Penthouse Dimension (Inside Penthouse Dimension + 12" (305)) Curb Inside Curb Dimension
LOUVERS
LP-31
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-32
lOUVERS
Continuous Blade Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o 25 psf (100 mph) 32.97 sq.ft. (3.063 sq.m.) 49.2%
Features Unique bolted conrer design affords excellent alignment of adjoining louver. Drainable blades with drain holes at corners. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 49% free area (based on 48 x 48 x 49.438"). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Penthouse Dimension + 16" (406)) Curb Inside Curb Dimension
ALL-WELDED CONSTRUCTION
LOUVERS
LP-33
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-34
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 43o 25 psf (100 mph) 31.59 sq.ft. (2.935 sq.m.) 49.4%
Features Storm proof blade with rain check. Positive locking corner joiner mounts from exterior. Slip-on corner cover requires no screws. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 49% free area (based on 48 x 48 x 48). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362) Outside Penthouse Dimension (Inside Curb Dim. + 8" (203))
Curb
ALL-WELDED CONSTRUCTION
LOUVERS
LP-35
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-36
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 35.40 sq.ft. (3.29 sq.m.) 55.3%
Features Storm proof blade with rain check. Positive locking corner joiner mounts from exterior. Slip-on corner cover requires no screws. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 55% free area (based on 48 x 48 x 48). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-37
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-38
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 45o 25 psf (100 mph) 31.84 sq.ft. (2.96 sq.m.) 49.8%
Features Positive locking corner joiner mounts from exterior. Slip-on corner cover requires no screws. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 50% free area (based on 48 x 48 x 48). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
4" (102)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362) Outside Penthouse Dimension (Inside Curb Dim. + 8" (203))
Curb
ALL-WELDED CONSTRUCTION
LOUVERS
LP-39
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-40
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 4 (102 mm) 39o 25 psf (100 mph) 35.40 sq.ft. (3.289 sq.m.) 55.3%
Features Drainable blade with vertical jamb gutter. Positive locking corner joiner mounts from exterior. Slip-on corner cover requires no screws. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 55% free area (based on 48 x 48 x 48). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
ALL-WELDED CONSTRUCTION
LOUVERS
LP-41
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
LP-42
lOUVERS
Visible Mullion Extruded Aluminum (Alloy 6063-T5) .081 (2 mm) .081 (2 mm) 6 (152 mm) 35o 25 psf (100 mph) 36.83 sq.ft. (3.422 sq.m.) 57.5%
Features Drainable blade with vertical jamb gutter. Positive locking corner joiner mounts from exterior. Slip-on corner cover requires no screws. Designed for snow load up to 50 psf (2,394 Pa), consult your local representative for higher loading. All welded construction: minimum 1 llet welds. Nominal 58% free area (based on 48 x 48 x 48). Optional bird and insect screens available. Optional insulated roof and roof curbs are available. Optional Duracron, Duranar and Duranar-XL baked enamel nish as per our standard color chart or any custom color.
6" (152)
Penthouse Height
Sectionned Roof with Standing Seams on Sizes Greater than 45" x 93" (1143 x 2362)
Outside Penthouse Dimension (Inside Curb Dim. + 8" (203)) Curb Mounting Straps Curb Inside Curb Dimension
ALL-WELDED CONSTRUCTION
LOUVERS
LP-43
All Metric dimensions ( ) are soft conversion. Imperial dimensions are converted to metric and rounded to the nearest millimetre.
Submittals
Description
Submittal Number
Date
E.H. Price Limited certies that the JE443 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Available Options
. Continuous Blade Construction (concealed mullions) . Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT
E.H. Price Limited certies that the ZE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publicati on 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Available Options
. Continuous Blade Construction (concealed mullions) . Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
E.H. Price Limited certies that the ZE445 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Available Options
. Continuous Blade Construction (concealed mullions) . Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
E.H. Price Limited certies that the DE439 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Available Options
. Continuous Blade Construction (concealed mullions) . Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
E.H. Price Limited certies that the DE635 shown herein is licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication 511 and comply with the requirements of the AMCA Certied Ratings Program The AMCA Certied Seal applies to air performance ratings and water penetration ratings
Available Options
. Continuous Blade Construction (concealed mullions) . Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
Standard Construction
Frame 2" x .063"(50 x 1.6) Extruded Aluminum (6063-T5) Blades J Style Blades, .063"(1.6) Extruded Aluminum (6063-T5) 30 0 blade angle, approximately 2"(50) blade spacing Finishes MILL Minimum Size 7" W x 5 7/16" H (178 x 138) Maximum Size 60" W x 120" H (1524 x 3048) * One piece construction
HEAD
Available Options
. Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
EXTERIOR
ALL-WELDED CONSTRUCTION
SILL
VERTICAL SECTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
Available Options
. Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
Available Options
. Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black) Free-Field Noise Reduction in Decibels Selected 1/3 Octave Bands Center Frequency Hz 63 13 125 8 250 10 500 1000 2000 4000 8000 13 21 25 22 23
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
Available Options
. Extended Sill (loose) 14 GA. Aluminum . Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated . Formed Flange and Mounting Angle up to 4" . Birdscreen: Aluminum or Galvanized . Insect Screen: Aluminum or Bronze . Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL . Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black) Free-Field Noise Reduction in Decibels Selected 1/3 Octave Bands Center Frequency Hz 63 16 125 13 250 15 500 1000 2000 4000 8000 18 16 18 18 21
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
243484
Available Options
. . . . . . . . Continuous Blade Construction (concealed mullions) Extended Sill (loose) 14 GA. Aluminum Blank-off Panels: Aluminum or Galvanized, Insulated or Non-Insulated Formed Flange and Mounting Angle up to 4" Birdscreen: Aluminum or Galvanized Insect Screen: Aluminum or Bronze Finishes: Prime Coat, Baked Enamel, Duranar , Duranar XL Anodized Finishes: Clear or Colour (Light Bronze, Medium Bronze, Dark Bronze, Black)
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG LOUVER SIZE WIDTH HEIGHT OPENING SIZE WIDTH HEIGHT
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . *
Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
Available Options
. . . . * Extended Sill (loose) 14 GA. Aluminum Variety of Bird & Insect Screens Wide variety of Finishes including: Baked Enamel, Prime Coat, Duranar & Duranar XL, Clear & Colour Anodize Roof Curb Select from PRICE Colour Chart or provide Colour sample to match
ALL-WELDED CONSTRUCTION
PROJECT ARCHITECT SPEC. SYMBOL QTY TAG INSIDE CURB DIMENSION WIDTH HEIGHT LENGTH
MOUNTING METHOD
Submittal Sheet
Mounting Method A (Standard)
Caulking (by others)
Masonary straps welded to the louver jambs on 16 (406) centers. 2 x 10 (50 x 254)
Do Not Caulk
Pressure Relief
PROJECT ARCHITECT SPEC. SYMBOL QTY LOUVER SIZE W (IN.) H (IN.) OPENING SIZE W (IN.) H (IN.)
Submittal Sheet
PROJECT ARCHITECT SPEC. SYMBOL QTY LOUVER SIZE W (IN.) H (IN.) OPENING SIZE W (IN.) H (IN.)
PENTHOUSE CURB
Submittal Sheet
PROJECT ARCHITECT SPEC. SYMBOL QTY LOUVER SIZE W (IN.) H (IN.) OPENING SIZE W (IN.) H (IN.)
Submittals
LOUVER SCHEDULE
Item Quan Type Louver Size WxH Sect Quan Section Size WxH Opening Size WxH Location or Designation
METHOD OF INSTALLATION
METHOD A - Installation method by others METHOD B - Installation with Flat Flange At: Head ____________ Sill ____________ Jamb ____________ On: Exterior ____________ or Interior ____________ Flange width: ____________ Mounting holes not included METHOD C - Installation with Angle Flange At: Head ____________ Sill ____________ Jamb ____________ On: Exterior ____________ or Interior ____________ Angle Extension: ____________ Mounting holes not included Angles shipped loose; eld mounting METHOD D - Installation with Masonry Strap Anchor 2" x 10" (51 x 254) Masonry strap anchor welded to jamb of louver
FINISH
Mill Prime Coat Baked Enamel Colour: Duranar Duranar XL Colour: ____________ Clear Anodize * Lt Bronze Anodize * Med Bronze Anod. * Dk Bronze Anod. * Black Anodize * * Aluminum only
SCREEN
None Interior Mounting Exterior Mounting 1/2" Mesh Bird Screen 3/4" Mesh Bird Screen 1" Mesh Bird Screen Other ____________ With Folded Frame Aluminum Galv Steel Bronze Other ____________
NOTES
Accessories / Installation
Description
Submittal Number
Date
Accessories
Mounting Methods Formed Metal Sill Standard / Multi-Section Insulated Blank-offs with Thermal Breaks Vertical Splicing 239450 239528 239531 January 1 / 06 January 1 / 06 January 1 / 06
Installation
Field Installation Multi-Section with Visible Vertical Mullion Field Installation Multi-Section with Continuous Blade Field Assembly Multi-Section Installation Screens / Blank-offs Vertical Splicing Field Installation Multi-Section Label / Section Assembly Sequence 239533 239532 239530 January 1 / 06 January 1 / 06 January 1 / 06
239529
January 1 / 06
MOUNTING METHODS
10 10 5
12 12 9
12 12 9
11 11 7
638 Raleigh Street Winnipeg, Manitoba Canada R2K 3Z9 Ph: 204.669.4220 Fax: 204.663.2715
Canadian Head Office, Laboratory & Manufacturing Facilities in Winnipeg, Manitoba Sales Offices or Representation in all major Canadian cities
The founding principles of our company have never changed business integrity, first-class service and a commitment to people. Price manufacturing endeavors arose from our belief that we could supply superior products and services at a reasonable price. Our mission is to become the worldwide supplier of preference for air distribution products and services. You can rely on Price our products and services with confidence. Product Improvement is a continuing endeavor at Price. Therefore, specifications are subject to change without notice. Consult your Price sales representative for current specifications or more detailed information.
Warranty: The Company warrants and guarantees that all goods within this catalogue that have been manufactured by the Company have been manufactured in accordance with the specifications published herein and will be free from defects in material and workmanship for a period of twelve (12) months from the date of Bill of Lading issued by the Company. The Company will replace defective product at its option, but will not be responsible for labor or material charges in replacing product or consequential damages. Any installation not conforming with the Company's specifications, manuals, bulletins or instructions or any misuse or any modification not authorized by the Company voids this warranty. This warranty is in lieu of all Provincial, State, and Federal statutory warranties and the conditions herein are in substitution and replacement of such warranties, statutory or otherwise.
E.H. Price Sales, a division of E.H. Price Limited. Price is a registered trademark of E.H. Price Limited. 2010.
A I R
D I S T R I B U T I O N
P R O D U C T S
F O R
W O R L D
C L A S S
C I T I E S
www.ehpricesales.com