Professional Documents
Culture Documents
Refer to the exhibit. What two statements can be concluded from the information that
is shown in the exhibit? (Choose two.)
All ports that are listed in the exhibit are access ports.
A router connected to the switch is needed to forward traffic between the hosts.
2
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
The router will forward the packet out interface FastEthernet 0/1.1 tagged for VLAN
10.
The router will forward the packet out interface FastEthernet 0/1.2 tagged for VLAN
60.
The router will forward the packet out interface FastEthernet 0/1.3 tagged for VLAN
60.
The router will forward the packet out interface FastEthernet 0/1.3 tagged for VLAN
120.
The router will not process the packet since the source and destination are on the same
subnet.
The router will drop the packet since no network that includes the source address is
attached to the router.
3
The information contained in a BPDU is used for which two purposes? (Choose two.)
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
to determine which ports will forward frames as part of the spanning tree
4
A router has two serial interfaces and two Fast Ethernet interfaces. This router must
be connected to a WAN link and to a switch that supports four VLANs. How can this
be accomplished in the most efficient and cost-effective manner to support inter-
VLAN routing between the four VLANs?
Connect a smaller router to the serial interface to handle the inter-VLAN traffic.
Add two additional Fast Ethernet interfaces to the router to allow one VLAN per
interface.
Connect a trunked uplink from the switch to one Fast Ethernet interface on the router
and create logical subinterfaces for each VLAN.
Use serial-to-Fast Ethernet transceivers to connect two of the VLANs to the serial
ports on the router. Support the other two VLANs directly to the available
FastEthernet ports.
5
When are MAC addresses removed from the CAM table?
6
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. Switch1 is not participating in the VTP management process with
the other switches. Which two are possible reasons for this? (Choose two.)
7
Which three must be used when a router interface is configured for VLAN trunking?
(Choose three.)
8
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. The switches are connected with trunks within the same VTP
management domain. Each switch is labeled with its VTP mode. A new VLAN is
added to Switch3. This VLAN does not show up on the other switches. What is the
reason for this?
VLANs cannot be created on transparent mode switches.
Server mode switches neither listen to nor forward VTP messages from transparent
mode switches.
There are no ports assigned to the new VLAN on the other switches.
9
Which two criteria are used by STP to select a root bridge? (Choose two.)
memory size
bridge priority
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
switching speed
number of ports
switch location
10
Which three steps should be taken before moving a Catalyst switch to a new VTP
management domain? (Choose three.)
Download the VTP database from the VTP server in the new domain.
Configure the VTP server in the domain to recognize the BID of the new switch.
Configure the switch with the name of the new management domain.
11
Which two items will prevent broadcasts from being sent throughout the network?
(Choose two.)
bridges
routers
switches
VLANs
hubs
12
Which two characteristics describe a port in the STP blocking state? (Choose two.)
13
What is the first step in the process of convergence in a spanning tree topology?
14
In which STP state does a switch port transmit user data and learn MAC addresses?
blocking
learning
disabling
listening
forwarding
15
What is the purpose of VTP?
16
Which statement best describes adaptive cut-through switching?
The switch initially forwards all traffic using cut-through switching and then changes
to store-and-forward switching if errors exceed a threshold value.
The switch initially forwards all traffic using cut-through switching and then changes
to fast-forward switching if errors exceed a threshold value.
The switch initially forwards all traffic using cut-through switching and then
temporarily disables the port if errors exceed a threshold value.
The switch initially forwards all traffic using store-and-forward switching and then
changes to cut-through switching if errors exceed a threshold value.
17
Using STP, how long does it take for a switch port to go from the blocking state to the
forwarding state?
2 seconds
15 seconds
20 seconds
50 seconds
18
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. The switches are interconnected by trunked links and are
configured for VTP as shown. A new VLAN is added to Switch1. Which three actions
will occur? (Choose three.)
Switch1 will not add the VLAN to its database and will pass the update to Switch 2.
Switch2 will add the VLAN to its database and pass the update to Switch3.
19
Which Catalyst feature causes a switch port to enter the spanning-tree forwarding
state immediately?
backbonefast
uplinkfast
portfast
20
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Refer to the exhibit. Which set of commands would be used on the router to provide
communication between the two hosts connected to the switch?
Router(config)# interface vlan 2
Router(config-if)# ip address 192.168.2.1 255.255.255.0
Router(config-if)# no shutdown
Router(config)# interface vlan 3
Router(config-if)# ip address 192.168.3.1 255.255.255.0
Router(config-if)# no shutdown