Professional Documents
Culture Documents
Haxorware Manual 0.9.2
Haxorware Manual 0.9.2
1 1 2 1 4 1 5 1 6 1 7 1 8 1 9 1 12 13 14 15 10 11
1 1
1 1
3 1
1 1
16
17 18
19 20
21
22
23 24
25
26
Information section:
1. This shows your MACs DHCP settings, such as the original configuration file name and the IP of the server it is on 2. Current IP addresses of the modem. HFC IP is the ip of the Coaxial interface and Eth IP is the ip of the network interface that connects to your computer. This is the IP you use to access the configuration page and telnet. It can be changed with the following Telnet or Web Shell commands: cd /non/msg dhcp_settings Remote access server IP address: [192.168.100.1] <Enter your new Eth IP here> Remote access server subnet mask: [255.255.255.0] <Just press Enter> Remote access server router: [192.168.100.254] <Just press Enter> write 3. The configuration file the modem is currently using. Clicking on the filename will allow you to save the config on your computer. 4. Current modems uptime.This shows how much time has passed since the modem was last restarted. The format is Days:Hours:Minutes:Seconds.
Administration section:
5. Telnet parameters. The checkbox indicates whether or not the telnet daemon is started at modem boot. If you do not use the telnet daemon, you can uncheck this to save 2KB of RAM on the modem. Also you can change the username and password that is requested when you connect to the telnet daemon. 6. Here you can change what Vendor, Model, and software version the modem reports when it is SNMP scanned and when it requests a HFC DHCP lease. For example, if you are using the MAC address of a ambit, it is a good idea to change these to reflect an Ambit modem to prevent suspicion.Clearing any of these boxes will return that box to the default Motorola values. 7. Since ISPs mainly do snmp scanning on the default SNMP ports (161 and 162), changing these will essentially block any snmp probes from the ISP. The default stealth ports are 225 and 226 for the snmp and trap ports respectively. 8. Checking the box here will make the modem ignore any DHCP settings set by the ISP for the HFC interface and instead use th static parameters defined here. This is useful for ISPs which do not give unregistered MAC addresses a valid DHCP lease, or give it a limited, walled garden IP. You can set any parameters that you want here, however if you set one out of the normal range of your ISP s HFC ips, your modem will probably not be able to access the TFTP and TOD servers.This will require you to autoserve a config to get it online. However, setting an IP out of range like this will make your modem virtually invisible to the isp, they cant scan it, and since it doesnt request a DHCP lease, they have no idea its even on. 9. This should be set to Disabled on most ISPs. The available options are: Disabled, Use DHCP, and Manual. If your ISP has the tftp-enforce option enabled in their CMTS, you will have to turn it on. If you arent using the Force Static IP option, the Use DHCP setting is best. This will simulate your modem getting the original configuration from the ISP before it loads a forced/autoserved one.However, if Force Static IP is ON, then there are no DHCP settings for the modem to use, and you will have to set this to Manual and specify the IP and filename in the boxes below. 10. If you have changed any settings in the Administration section, you will have to click this button to permanently save them.
Utility functions:
11. This will perform a soft restart of the modem, saving any settings before rebooting.Equivalent to the /reset command in the Broadcom shell. 12. This will disable all the IP filters that your modem is using.Equivalent to the /snmp/cm_filters off command in the Broadcom shell. Some ISPs use IP filters to block certain traffic such as port 80 incoming, which will block you from hosting any web servers. Disabling the filters makes all ports open. 13. This will erase all the dynamic settings in the modem. I have added this option here simply because some people that have had infinite firmware previously running on their modems have the dynamic settings in a weird state that will make the modem crash after parsing the configuration file. Note that a soft reset will rewrite all the dynamic settings back into the modem, so usually after clicking this you will have to do a hard reset (power cycle the modem).
Addresses section:
14. You can change the MAC addresses and the Serial number of the modem here. Note that all 3 MAC addresses MUST be different from each other. If they arent all hell will break loose when the modem tries to get online. These addresses vary depending on the modem vendor, on Motorola modems the Ethernet MAC will be the HFC MAC +1 and the USB mac is a completely different number. You will only need to change the HFC MAC in order to clone the address of another modem. The others are irrelevant (except the serial number which may also need to be cloned on some ISPs). 15. Clicking this button will save any of the changes you have made to the addresses. Note that all the fields must be filled out (none must be left blank) and be in a proper format otherwise you will receive an error and the addresses wont be changed.
Autoserve section:
16. This checkbox toggles the Autoserve feature. Autoserve is a feature that allows the modem to host its own config, removing the need to have a TFTPD on another computer or on a Router in order to use configs that arent available on the ISPs servers such as custom or outdated ones (that are still valid of course). A config must be uploaded in the flash memory of the modem (use the upload form below this checkbox to do so) for this feature to work. If Autoserve is enabled, the Forced config settings in the section below are ignored. 17. If you have toggled the checkbox for the Autoserve feature, you will have to click this button to apply the change. 18. Use this form to upload a configuration file from your computer to the modems flash for use in the Autoserve function. Please do not use long file names or names with special characters as this may break something. Once you have browsed and selected an appropriate file, click Upload to save it to the modem.