Professional Documents
Culture Documents
NE/SA/SE532 LM258/358/A/2904: Low Power Dual Operational Amplifiers
NE/SA/SE532 LM258/358/A/2904: Low Power Dual Operational Amplifiers
Philips Semiconductors
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
DESCRIPTION
The 532/358/LM2904 consists of two independent, high gain, internally frequency-compensated operational amplifiers internally frequency-compensated operational amplifiers designed specifically to operate from a single power supply over a wide range of voltages. Operation from dual power supplies is also possible, and the low power supply current drain is independent of the magnitude of the power supply voltage.
PIN CONFIGURATION
D, DP, and N Packages
OUTPUT A INVERTING INPUT A NON INVERTING INPUT A V 1 2 3 4 A + B + 8 7 6 5 V+ OUTPUT B INVERTING INPUT B NON INVERTING INPUT B
UNIQUE FEATURES
In the linear mode the input common-mode voltage range includes ground and the output voltage can also swing to includes ground and the output voltage can also swing to ground, even though operated from only a single power supply voltage. The unity gain cross frequency is temperature-compensated. The input bias current is also temperature-compensated.
SL00282
FEATURES
Internally frequency-compensated for unity gain Large DC voltage gain: 100 dB Wide bandwidth (unity gain): 1 MHz (temperature-compensated) Wide power supply range single supply: 3 VDC to 30 VDC, Very low supply current drain (400 A)essentially independent Low input biasing current: 45 nADC temperature-compensated Low input offset voltage: 2 mVDC, and offset current: 5nADC Differential input voltage range equal to the power supply voltage Large output voltage: 0 VDC to V+ 1.5 VDC swing
EQUIVALENT CIRCUIT
V+ 6 A 100 A 6 A Q5 Q6 CC Q7
Q2 Q1
Q3 Q4
RSC OUTPUT
INPUTS
Q13
50 A
SL00283
2002 Jul 12
853-1241 28616
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
ORDERING INFORMATION
DESCRIPTION 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Thin Shrink Small Outline Package (TSSOP) 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Thin Shrink Small Outline Package (TSSOP) 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Plastic Small Outline (SO) Package 8-Pin Plastic Dual In-Line Package (DIP) 8-Pin Plastic Dual In-Line Package (DIP) TEMPERATURE RANGE 0 C to +70 C 0 C to +70 C 40 C to +85 C 40 C to +125 C 40 C to +125 C 40 C to +125 C 25 C to +125 C 25 C to +125 C 0 C to +70 C 0 C to +70 C 0 C to +70 C 0 C to +70 C 0 C to +70 C 55 C to +125 C ORDER CODE NE532D NE532N SA532D LM2904D LM2904DP LM2904N LM258D LM258N LM358D LM358DP LM358N LM358AD LM358AN SE532N DWG # SOT96-1 SOT97-1 SOT96-1 SOT96-1 SOT505-1 SOT97-1 SOT96-1 SOT97-1 SOT96-1 SOT505-1 SOT97-1 SOT96-1 SOT97-1 SOT97-1
PD
1160 780 714 Continuous 0 to +70 25 to +85 40 to +125 40 to +85 55 to +125 65 to +150 230
mW mW mW
Tamb
C C C C C C C
Tstg Tsld
NOTE: 1. Derate above 25 C, at the following rates: N package at 9.3 mW/C D package at 6.2 mW/C DP package at 5.72 mW/C 2. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 VDC, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction.
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
DC ELECTRICAL CHARACTERISTICS
Tamb = 25 C; V+ = +5 V, unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS RS = 0 RS = 0 ; over temp. RS = 0 ; over temp. IIN(+) IIN() Over temp. Over temp. IIN(+) or IIN() IIN(+) or IIN(); Over temp. Over temp. V+ = 30 V V+ = 30 V; Over temp. V+ = 30 V RL 2 k; V+ = 30 V; over temp. RL 10 k; V+ = 30 V; over temp. RL 10 k; over temp. RL = ; V+ = 30 V ICC Supply current RL= on all amplifiers; V+ = 30 V; over temp. RL 2 k; VOUT 10 V AVOL Large-signal voltage gain Supply voltage rejection ratio Amplifier-to-amplifier coupling4 V+=15V (for large VO swing); over temp. RS = 0 f = 1 kHz to 20 kHz (input referred) VIN+ = +1 VDC; VIN = 0 VDC; V+ = 15 VDC VIN+ = +1 VDC; VIN = 0 VDC; V+ = 15 VDC; over temp. VIN = +1 VDC; VIN+ = 0 VDC; V+ = 15 VDC Output current (Sink) VIN = +1 VDC; VIN+ = 0 VDC; V+ = 15 VDC; over temp. VIN+ = 0 V; VIN = +1 VDC; VO = 200 mV ISC GBW SR VNOISE Short circuit current5 Differential input voltage6 Unity gain bandwidth Slew rate Input noise voltage Tamb = 25 C Tamb = 25 C Tamb = 25 C; f = 1 kHz 1 0.3 40 20 10 10 5 12 50 25 65 100 120 40 20 20 8 50 40 60 V+ 1 0.3 40 20 10 10 5 12 0 0 70 26 27 28 5 0.5 0.6 100 20 1.0 1.2 25 15 65 100 120 40 20 20 8 50 40 60 V+ 85 10 45 40 50 V+1.5 V+2.0 0 0 65 26 27 28 5 0.5 0.6 100 20 1.0 1.2 70 150 300 7 3 30 100 10 45 40 50 V+1.5 V+2.0 250 500 SE532, LM258 Min VOS VOS IOS IOS IBIAS S IB VCM C CMRR VOH O VOL Offset voltage1 Drift Offset current Drift Input current2 Drift Common-mode voltage g range3 Common-mode rejection ratio Output voltage swing Output voltage swing Typ 2 Max 5 7 7 5 50 150 NE/SA532/ LM358/LM2904 Min Typ 2 Max 7 9 mV mV V/C nA nA pA/C nA nA pA/C V V dB V V mV mA mA V/mV V/mV dB dB mA mA mA mA A mA V MHz V/s nV/Hz UNIT
PSRR
IOUT
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
NOTES: 1. VO 1.4 V, RS = 0 with V+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ 1.5 V). 2. The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the input lines. 3. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is V+ 1.5 V, but either or both inputs can go to +32 V without damage. 4. Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be detected as this type of capacitance coupling increases at higher frequencies. 5. Short-circuits from the output to V+ can cause excessive heating and eventual destruction. The maximum output current is approximately 40 mA independent of the magnitude of V+. At values of supply voltage in excess of +15 VDC, continuous short-circuits can exceed the power dissipation ratings and cause eventual destruction. 6. The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range is V+ 1.5 V, but either or both inputs can go to +32 VDC without damage.
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
Current Limiting
160
Voltage Gain
RL + 20 k
40
Voltage-Follower Response
4 RL < 2 k V+ 15 VDC 3 2 1 0
100 k + VO 2 k
VO
10
3 2 1 0 0 10 20 TIME (s) 30 40
1k
10k
100k
1M
FREQUENCY (Hz)
450 IN 400
EO 50 pF
INPUT
Tamb = +25 C 0.01 0.1 1 10 100 0.01 0.001 0.01 0.1 1 10 100
t TIME (s)
SL00284
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
Input Current
VCM = 0 VDC
100
V+ = +30 VDC
10 NEGATIVE POSITIVE 5
80 +7.5 VDC 60 40 + VIN 20 0 100 1k 10k 100k f FREQUENCY (Hz) 1M 100 k 7.5 VDC 100 100 + 100 k VO
V+
= +15 VDC
V+ = +5 VDC
10
15
25
45
65
85 105 125
SL00285
TYPICAL APPLICATIONS
RF V+ VIN RIN 8 10 k VO 4 RL V+ 2 BLOCKS DC. GAIN V+ V+ 2 VIN 10 k V+ 8 V+
+ +
4 VO
R1
RF
10 k
V+ 8
VIN 10 k
+
4 VO
Non-Inverting Amplifier
SL00286
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
SOT96-1
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
SOT97-1
2002 Jul 12
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm
SOT505-1
2002 Jul 12
10
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
NOTES
2002 Jul 12
11
Philips Semiconductors
Product data
NE/SA/SE532/ LM258/358/A/2904
Product data
Production
[1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com.
Definitions
Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
Disclaimers
Life support These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Contact information
For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825
Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Date of release: 08-02
Philips Semiconductors
2002 Jul 12 12
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.