Professional Documents
Culture Documents
300x400x63 (AASHTO)
300x400x63 (AASHTO)
Feb.08, 2014
REVISIONS
CONTRACTOR
CONTRACT
P2014-042 Project: Wadi bin Hashbal bridge
Location :
SHOP DRAWING
TITLE :
ELASTOMERIC BEARING
30040063
SCALE : DATE :
(SHEET 1 of 1)
AS SHOWN
Feb.08, 2014
EB/01
Rev 00
02/08/2014 Lgq
REV 00
Criterion:
AASHTO:Section 14:2004
Design parameter Type 300x400x63 Vmax VD VL Hmax S s G Fy Vmax (kN) 1200 VD (kN) VL (kN) Hmax (kN) 120 s (rad) 0.005 s (mm) 24 G (Mpa) 1 Fy (Mpa) 235
is the maximum vertical design load; is the dead load; is the live load; is the maximum horizontal design load; is maximum shear deformation of the elastomer at service limit state is maximum Rotation is the shear modulus is the stress in the steel. W (mm) 300 L (mm) 400 H (mm) 63 hri (mm) 10 4 n hs (mm) 3 5 ns h0 (mm) 4 hPTFE (mm) 0 hrt (mm) 48
is the overall length of the bearing; is the overall width of the bearing; is the overall thickness of the bearing; is the thickness of an individual elastomer layer; is the thickness of elastomer layer to the contact surfaces; is the thickness of steel reinforcing plate; is the number of individual elastomer layer;
Page 1
02/08/2014 Lgq
REV 00
Criterion:
AASHTO:Section 14:2004
ns hPTFE hrt
is the number of steel reinforcing plate. is the thickness of PTFE plate ; is the total thickness of elastomer ;
s =
Type
V max L W
L =
VL L W
L Mpa 0.00
300x400x63 s L
is average compressive stress due to the Vmax; is average compressive stress due to the VL
2. The top and bottom cover layers shall be no thicker than 70% of the internal layers. h00.7hri Type 300x400x63 0.7hri mm 7 CHECK OK 14.7.5.1
Page 2
02/08/2014 Lgq
REV 00
Criterion:
S =
Type
LW 2 h ri ( L + W )
S 8.57
for bearings subject to shear deformation s1.66GS and s11.0MPa L0.66GS Type 300x400x63 s (Mpa) 10.00 1.66GS 14.23 (14.7.5.3.2-1) (14.7.5.3.2-2) CHECK OK (14.7.5.3.2-3) (14.7.5.3.2-4) s (Mpa) 10.00 2.00GS 17.14 CHECK OK L Mpa 0.00 1.00GS 8.57 CHECK OK L Mpa 0.00 0.66GS 5.66 CHECK OK
for bearings fixed against shear deformation s2.00GS and s12.0MPa L1.00GS Type 300x400x63
Page 3
02/08/2014 Lgq
REV 00
Criterion:
AASHTO:Section 14:2004
5Shear deformation S hrt2S Type 300x400x63 6Satisfy uplift hrt (mm) 48 2 s (mm) 48 (14.7.5.3.4- 1) CHECK OK
s 1 .0 GS (
Type 300x400x63
s B
) n h ri
1.0GS(s/n)(B/hri) 9.64
CHECK OK
Type 300x400x63
2 1.875GS[1-0.2(s/n)(B/hri) ]
CHECK OK
12.46
Page 4
02/08/2014 Lgq
REV 00
Criterion:
AASHTO:Section 14:2004
Type 300x400x63
2 2.250GS[1-0.167(s/n)(B/hri) ]
CHECK OK
15.66
A =
B=
1 . 92
2 .67 L (S + 2 .0 ) 1 + 4 .0W
2A 0.389 B 0.213
h rt L 2 .0 L 1+ W
Type 300x400x63
Page 5
02/08/2014 Lgq
REV 00
Criterion:
AASHTO:Section 14:2004
Further check: For rectangular bearings not satisfying above Equation,an additional check shall be made in accordance with the following Equation: The bridge deck is free to translate horizontally.
s
Type 300x400x63
GS 2A B
s (Mpa) 10.00 48.73
(14.7.5.3.6-4)
GS/(2A-B)
CHECK OK
h s
and
3 . 0 h ri s Fy
2 . 0 h ri L FTH
14.7.5.3.7-1
hs >
14.7.5.3.7-2
FTH is the constant amplitude fatigue threshold for Category A as specified in Article 6.6, FTH=165MPa. Type 300x400x63 3.0hris/Fy 1.28 CHECK OK 2.0hriL/FTH 0.00 CHECK OK
Page 6