Professional Documents
Culture Documents
Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
LIST OF SYMBOLS Maximum cantilever length (inches); measured from the face of block to edge of foundation Maximum deflection (inches), for estimating the fundamental natural frequency of beam or column Rotor eccentricity for centrifugal machines First coupled natural frequency Second coupled natural frequency Machine operating speed (cps or rpm) Damped resonant frequency (cps or rpm) Undamped natural frequency (cps or rpm) Concrete compressive strength Yield strength of reinforcement Uncoupled natural frequency in translational x direction Uncoupled natural frequency in translational y direction Uncoupled natural frequency in translational z directions Uncoupled natural frequency , rocking about X Uncoupled natural frequency , rocking about Y Uncoupled natural frequency , rocking about z, Torsional Parameters for calculating single pile stiffnesses in horizontal (X), Parameters for calculating single pile stiffnesses in vertical (Z), Parameters for calculating single pile stiffnesses in rocking () modes Parameters for calculating single pile damping coefficients in horizontal (X), Parameters for calculating single pile damping coefficients in vertical (Z) Parameters for calculating single pile damping coefficients in rocking () modes, Acceleration of gravity (32.2 ft/sec2 or 386.4 in/sec2)
Civildesignhelp.info
PAGE 1 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. h hi l m me r r0 t A0 Ai Ap B Bx By Bz B
B
Foundation embedment depth, the distance between the CG of a machine foundation system and the foundation base. Thickness of ith soil layer Embedded length of a pile Total mass of a machine (machine+foundation) Rotor mass for centrifugal machines foundation system
Frequency ratio, defined as f0/fd (or f0/fn) Equivalent radius of foundation; equivalent radius of concrete pile,
Ap
Thickness of mat foundation or pile cap displacement amplitude Stress influence area (spreading below the foundation at a ratio of 2 vertical to 1 horizontal) measured at the centroid of ith soil layer Cross sectional area of concrete pile Foundation width, parallel to the y-axis Mass ratios for calculating the soil geometrical damping ratios in horizontal X directions Mass ratios for calculating the soil geometrical damping ratios in horizontal Y directions Mass ratios for calculating the soil geometrical damping ratios in vertical Z directions Mass ratios for calculating the soil geometrical damping ratios in rocking about X () directions Mass ratios for calculating the soil geometrical damping ratios in rocking about Y () directions Mass ratios for calculating the soil geometrical damping ratios in torsional about Z () directions Damping coefficients for a single pile in horizontal (X) direction Damping coefficients for a single pile in vertical (Z) direction Damping coefficients for a single pile in rocking about X () directions System damping or equivalent modal damping ratio for a coupled vibrational motion Soil or soil-pile damping ratios in horizontal X directions
B
B
B
B
Cx Cz C D Dx
Civildesignhelp.info
PAGE 2 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Dy Dz D D D Ep F0 Fn Fx Fy Fz Soil or soil-pile damping ratios in horizontal Y directions Soil or soil-pile damping ratios in vertical (Z) directions Soil or soil-pile damping ratios in rocking about X() directions Soil or soil-pile damping ratios in rocking about Y ()directions Soil or soil-pile damping ratios in torsional about Z () directions Young's modulus of concrete pile Machine unbalanced force for centrifugal machines Unbalanced force at natural frequency of the foundation system Unbalanced force in horizontal x direction Unbalanced force in horizontal y direction Unbalanced force in vertical z direction Dynamic soil shear modulus Weighted average soil shear modulus Mass moment of inertia at the C.G. of a machine foundation Area moment of inertia of single pile Mass moments of inertia at the foundation base in rocking about X () direction Mass moments of inertia at the foundation base in rocking about Y () direction Mass moments of inertia at the foundation base in torsional about Z () direction Soil dynamic subgrade reaction (lbs/in3) Soil spring constants or translational X direction. Soil spring constants or translational Y direction. Soil spring constants or translational Z direction. Soil spring constants or rotational modes Soil spring constants or rotational modes Soil spring constants or rotational modes single pile spring constants in single pile spring constants in single pile spring constants in single pile spring constants in single pile spring constants in single pile spring constants in
G, Gs Gavg Io Ip I I I Ks Kx Ky Kz K K K
Civildesignhelp.info
PAGE 3 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. (Ki)g L M M M N Ni V0 Vp Vs W We X Y Z x z x y z Pile spring constants for a pile group foundation length, parallel to the X-axis . Unbalanced moments about X (), Unbalanced moments about Y (), Unbalanced moments about Z (), Number of soil layers; number of piles Dynamic amplification factors at ith vibrational motion Maximum velocity amplitude Compression wave velocity of pile, Shear wave velocity of soil
E p g/ p
Cartesian coordinates in horizontal X (parallel to L) Cartesian coordinates in horizontal Y (parallel to B ) Cartesian coordinates in vertical Z Coefficients for soil damping calculation due to embedment effect in horizontal (X), Coefficients for soil damping calculation due to embedment effect in vertical (Z) Coefficients for soil damping calculation due to embedment effect in rocking about X () mode Coefficients for soil damping calculation due to embedment effect in rocking about Y () mode I0 I0 or I I Geometrical coefficients for soil spring calculation for rectangular foundation in translational X direction. Geometrical coefficients for soil spring calculation for rectangular foundation in translational Y direction. Geometrical coefficients for soil spring calculation for rectangular foundation in translational Z direction. Geometrical coefficients for soil spring calculation for rectangular foundation in rotational about X () modes. Geometrical coefficients for soil spring calculation for rectangular foundation in rotational about Y () modes. Correction factor for soil damping calculation in rocking mode
Civildesignhelp.info
PAGE 4 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. s p s x y z Weight density of soil (Ds x g) Weight density of concrete pile Mass density of soil Poisson's ratio of soil Machine operating speed (rad/sec) Coefficients for soil spring calculation effect in horizontal X direction. Coefficients for soil spring calculation effect in horizontal Y direction. Coefficients for soil spring calculation effect in vertical Z direction. Coefficients for soil spring calculation effect rocking about X () Coefficients for soil spring calculation effect rocking about Y () rotation about vertical Z-axis (torsion) rotation about horizontal X-axis (rocking) rotation about horizontal Y-axis (rocking)
due to embedment due to embedment due to embedment due to embedment due to embedment
Civildesignhelp.info
PAGE 5 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Horizontal Peak Velocity (in./sec) <0.005 0.005-0.010 0.010-0.020 0.020-0.040 0.040-0.080 0.080-0.160 0.160-0.315 0.315-0.630 >0.630
Machine Operation Extremely smooth Very smooth Smooth Very good Good Fair Slightly rough Rough Very rough
Civildesignhelp.info
PAGE 6 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 2 ROTOR ECCENTRICITIES
Machine
Centrifugal Compressors and Turbines Centrifugal Compressors and Turbines Gear Units Gear Units Motors Motors Motors
f 3000
f > 3000 f 8000 f > 8000 f 1500 1500 < f < 3000 f 3000
12000 f
0.8 0.5 1.5 1 0.5
Civildesignhelp.info
PAGE 7 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 3 SOIL SPRING CONSTANTS FOR RECTANGULAR FOUNDATION Mode of Vibration Horizontal (X) Soil Spring Constants
K x = 2(1 + ) G x BL x
Horizontal (Y)
K y = 2(1 + ) G y
BL y
Vertical (Z)
Kz =
G (1 - ) z
BL z
Rocking (about X)
K =
G B2 L (1 - )
Rocking (about Y)
K =
G B L2 (1 - )
Torsional (about Z)
K =
16 G r 3 o 3
Civildesignhelp.info
PAGE 8 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 4 SOIL SPRING COEFFICIENTS FOR SOIL SPRING CALCULATION INCLUDING EMBEDMENT EFFECT Mode of Vibration Horizontal (X & Y) Equivalent Radius (ro) Soil Spring Coefficient
BL
Vertical (Z)
BL
z = 1 + 0.6(1 - )
ro
3
Rocking (about X)
B3 L 3
Rocking (about Y)
BL 3
Torsional (about Z)
BL( B2 + L2 ) 6
N/A
* h = embedment depth
Civildesignhelp.info
PAGE 9 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 5 GEOMETRICAL DAMPING RATIOS FOR RECTANGULAR FOUNDATION (INCLUDING THE EMBEDMENT EFFECT)
Mass Ratio
(1 - ) m 4 s r3 o (7 - 8 ) m 32(1 - ) s r 3 o
Bz =
Horizontal (X or Y)
Bx =
Dx =
Rocking (about X)
B =
3(1 - ) I 8 sr 5 o
3(1 - ) I 8 sr 5 o
D =
0.15 (1 + B ) B 0.15 (1 + B ) B
Rocking (about Y)
B =
D =
Torsional (about Z)
B =
I sr 5 o
D =
0.5 1 + 2 B
Civildesignhelp.info
PAGE 10 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 6 DAMPING COEFFICIENTS FOR SOIL DAMPING CALCULATION INCLUDING EMBEDMENT EFFECT
Damping Coefficient
z =
h 1 + 1.9(1 - ) ro z h 1 + 1.9(2 - ) ro x
Horizontal (X or Y)
x =
Rocking (about X)
3 h h 1 + 0.7(1 ) + 0.6(2 ) ro ro
Rocking (about Y)
3 1 h h 1 + 0.7(1 - ) = + 0.6(2 - ) r o ro
Torsional (about Z)
N/A
Civildesignhelp.info
PAGE 11 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 7 CORRECTION FACTOR FOR SOIL DAMPING CALCULATION IN ROCKING MODE
Civildesignhelp.info
PAGE 12 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 8 PILE STIFFNESSES FOR A SINGLE PILE
Pile Stiffness
3 Kx = Ky = E p I p f x ,1 / r o
Vertical (Z)
K z = E p A p f z ,1 / r o
Rocking (about X or Y)
K = K = E p I p f ,1 / r o
Torsional (about Z)
N/A
Civildesignhelp.info
PAGE 13 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 9 DAMPING COEFFICIENTS FOR A SINGLE PILE
Damping Coefficient Cz = E p A p f z ,2 Vs
2 Cx = E p I p f x ,2 ( r o
C = E p I p f ,2 Vs N/A
Civildesignhelp.info
PAGE 14 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 10 PILE STIFFNESS AND DAMPING PARAMETERS fx,1 , fx,2 , f,1 AND f,2
s/ p
Vs Vp
0.01 0.4 0.7 (Concrete) 0.02 0.03 0.04 0.05 0.25 0.7 (Concrete) 0.01 0.02 0.03 0.04 0.05
0.0036
0.202
0.0084
0.139
Civildesignhelp.info
PAGE 15 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 11 PILE STIFFNESSES FOR A PILE GROUP
Mode of Vibration
Vertical (Z)
( K z )g =
i=1
K zi
Horizontal (X or Y)
( Kx )g = ( Ky )g =
n
i=1
Kxi
Rocking (about X)
( K )g =
( K
i=1
n
+ K zi yi2 )
Rocking (about Y)
( K )g =
( K
i=1
+ K zi xi2 )
Torsional (about Z)
( K )g =
i=1
2 2 K xi ( xi + yi )
Civildesignhelp.info
PAGE 16 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 12 DAMPING RATIOS FOR A PILE GROUP
Damping Ratios
Dz = Cz 2 ( K z )g m Cx 2 ( K x )g m
Horizontal (X or Y)
Dx =
Rocking (about X)
D =
C + Cz yi2 2 ( K )g I
Rocking (about Y)
[C + Cz xi2 ] 2 ( K )g I
Torsional (about Z)
Cx ( xi2 + yi2 ) D = 2 ( K )g I
Civildesignhelp.info
PAGE 17 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 13 CALCULATION OF UNCOUPLED NATURAL FREQUENCIES
1 2
Kz m
fnx =
1 2
1 2
Kx m
Ky m
Horizontal (Y)
fny =
Rocking (about X)
fn =
1 2
K I
Rocking (about Y)
fn =
1 2
K I
Torsional (about Z)
fn =
1 2
K I
Civildesignhelp.info
PAGE 18 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 14 CALCULATION OF DISPLACEMENT AMPLITUDES BASED ON UNCOUPLED MODES OF VIBRATION Mode of Vibration Vertical (Z) Horizontal (X) Displacement Amplitudes dz = Nz Fz Kz
dx = Nx
Fx Kx
Horizontal (Y)
dy = Ny
Fy Ky
Rocking (about X)
= N
M K
Rocking (about Y)
= N
M K
Torsional (about Z)
= N M
K
Ni =
mode.
1 (1 - r )
2 i 2
(2 D i r i )
, where, ri =
Civildesignhelp.info
PAGE 19 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. Table 15 CALCULATION OF TOTAL DISPLACEMENT AMPLITUDE BASED ON UNCOUPLED MODES OF VIBRATION
Displacement Amplitude
Z = d Z + ( Y) + ( X) X = d X + ( Y) + ( Z) Y = d Y + ( X) + ( Z)
Ao =
x, y and z are the distances from the center of foundation base to the point where the amplitude is determined.
Civildesignhelp.info
PAGE 20 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Civildesignhelp.info
PAGE 21 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Civildesignhelp.info
PAGE 22 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Civildesignhelp.info
PAGE 23 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Civildesignhelp.info
PAGE 24 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
Figure 5: Vertical Pile Stiffness and Damping Parameters for Friction Piles
Civildesignhelp.info
PAGE 25 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design.
1 2 2 f nx + f n + 2
1 2 2 f nx + f n 2
1 2 1 2 Kx m K I
(f
(f
2 nx
2 nx
2 2 2 + f2 n ) - 4 f nx f n
2 2
2 2 2 + f2 n ) - 4 f nx f n
Where,
fnx =
fn =
Kx: K:
Civildesignhelp.info
PAGE 26 OF
27
Following tables and graphs are copied from different text books available in the market. Before using these tables and graphs please check with text books available with you / library. Civildesignhelp.info is not responsible for any error in foundation analysis and design. m: I: total mass of a machine foundation system Io + mh2, the mass moment of inertia at the foundation base Io: the mass moment of inertia at the C.G. of a machine foundation system h: the distance between combined C.G. and the base of a machine foundation
I0 I
Note that the coupling effect becomes insignificant and can be neglected when the two coupled frequencies are determined to be away from the machine operating speed by at least 40%.
Civildesignhelp.info
PAGE 27 OF
27