A few things to keep in mind while completing this activity
Do not use the browser Back button or close or reload any !"am windows during the e"am# Do not close Packet Tracer when you are done# It will close automatically# Click the Submit Assessment button to submit your work# Introduction In this practice Packet Tracer Skills !"am you will finish the configuration of a partially configured network establish connectivity between the routers and from the routers to the Internet configure D$CP configure port security configure PPP encapsulation on %A& links verify connectivity to the Internet Addressing Table Device Interface Address Subnet Mask Default Gateway Branch 'a()( *+,#*-.#,(#-/ 255.255.255.22 4 n)a S()()( *+,#*-.#,(#-, 255.255.255.22 4 n)a 'a()* *+,#*-.#,(#+0 255.255.255.22 4 n)a $1 'a()( *+,#*-.#,(#* 255.255.255.22 4 n)a S()()( ,(+#*-/#,(*#, 255.255.255.25 2 n)a S()()* *+,#*-.#,(#22 255.255.255.22 4 n)a %ireless AP Internet *+,#*-.#,(#, 255.255.255.22 4 *+,#*-.#,(#* 3A& Switch* 43A& * *+,#*-.#,(#-- 255.255.255.22 4 *+,#*-.#,(#-/ PC 5 C *+,#*-.#,(#*,- 255.255.255.22 4 *+,#*-.#,(#+0 PC 5 A DHCP DHCP DHCP DHCP PC 5 B DHCP DHCP DHCP DHCP
Note: The password for user !6!C mode is cisco# The password for privileged !6!C mode isclass# Step : !onnect t"e Devices# a# Connect the Serial ()()( on 7outer* to 7outer,# 7outer, is the DC! side of the link# b# Connect the 'ast !thernet ()( on 7outer, to the %ireless AP# Crossover tussen wireless# Serial van router , DC! naar router * Step $: !onfigure t"e Device Basics# Configure the following on 7outer* The router name is Branc"# Conf t $ostname Branch The privileged !6!C mode uses the following encrypted password class %nable !onf t %nable secret class !nable Telnet and console line login using the following password line vty 0 4 password cisco transport input telnet Line console 0 password cisco Login Configure the banner message5of5the5day as banner motd 8&naut"ori'ed access will be prosecuted9 !nter T!6T message# !nd with the character :;:# Authori<ed access only= Step (: Design and !onfigure I) Addressing# >se the IP addresses in the Addressing Table and your subnetting skills to determine the missing IP addresses according to the following guidelines a# Configure 7outer* Addressing# Configure the Serial ()()( interface on 7outer* using the last IP address in the subnet that is shared with 7outer,# *+,#*-.#,(#-, The 3A& that is attached to 7outer* uses the ne"t available ),. subnet in the *0,#*-#*((#(),? address space# Configure 7outer* with the first IP address# *+,#*-.#,(#22 b# Configure Switch* Addressing# Configure the default management interface on Switch* with the second available IP address in the 7outer* 3A& subnet# Int vlan 1 Ip address 192.168.20.66 No shut exit Configure the default gateway# ip deault!"ate#a$ 192.168.20.65 Step *: !onfigure D+!) for t"e ,outer -AN# a# PC* and PC, receive addressing from D$CP# Configure 7outer* as the D$CP server with the following parameters !"clude the first three addresses in the 7outer* 3A& subnet from the D$CP pool# ip dhcp e"cluded5address *+,#*-.#,(#-/ *+,#*-.#,(#-0 &ame the pool ,outer.-AN @case5sensitive;# !n Conf t Ip dchp pool DAT-? &etwork *+,#*-.#,(#-? ,//#,//#,//#,,? default5router *+,#*-.#,(#-/ Configure -?#*((#(#/ as the D&S server# dns *+,#(#,#/ b# >se the command prompt to verify that PC* and PC, have received legal IP addressing# Ipconfig /release Ipconfig /renew Step 0: !onfigure and 1erify )ort Security# Configure Switch* with port security on 'ast!thernet ()2# !n Conf t Int fa()2 Switchport mode access Switchport port5security &o more than , BAC addresses are allowed# Switchport port5security ma"imum , Ance learnedC BAC addresses should 8stick9 to the running configuration# Switchport port5security mac5address sticky 4erify that port security is implemented# Step 2: !onfigure and 1erify ,outing# Configure 7outer* and 7outer, with a static route to reach the *(#,//#,//#(),? wireless 3A&# >se the ne3t4"op I) address argument in your commands# b# Configure 7outer* and 7outer, with a default route to the Internet# >se the outbound interface argument in your commands# $1Dconf t int s()()( ip route (#(#(#( (#(#(#( s()()( BranchDconf t int s()()( ip route (#(#(#( (#(#(#( s()()( c# Configure 7outer* and 7outer, to share routing information for internal networks only# >se 7IPv,# d# 4erify connectivity# Step 5: !onfigure and 1erify 6AN %ncapsulation# a# Configure the 7outer, link to the Internet with PPP# BranchD conf t Int s()()( %ncapsulation ppp b# Configure both sides of the link between 7outer* and 7outer, with PPP# $1D Int s()()( %ncapsulation ppp $1D conf t Int s()()* %ncapsulation ppp ,outer rip 1ersion $ Network 7## c# 4erify connectivity# The wireless PC should be able to ping PC* and PC, and the Cisco server# &! EAB>DF &APISATF CAPG 7>& STA7T &A 7A>T!7A6 I S%ITC$!;;; By shynggys