SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT
B.Tech. [SEM V (ME)]
QUIZ TEST-1
(Session: 2013-14)
\ \ MACHINE DESIGN-I
Timé: I hour (EME-501) Max. marks : 3
Roll No. F ey
(To be filed bythe Studen)
Note: All questigns are compulsary.
Part-A
(Questions from Tutorial Sheet) [10 Marks}
Ql]. What down the role of ‘STANDERISATION* in machine design . Expl short.
(QNeNIS)
Phe principal stresses induced at a point in a machine components made of steel S0C4.(Syt=460N/te95 asc
Wws: o1=200N/m2 02 =150N/m2, 030. Caleulate factor of'safety by the maximum shear stress theory.
{QNo.7}{5)
Part—B f rks}‘Academich26
Refer/WV/ACADIIS |
SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT
B.Tech. [SEM V (ME)]
QUIZ TEST-1
(Session: 2013-19)
MACHINE DESIGN-I
5 Time: 1 hour (EME-501) Max. marks : 30
Rone. [i eaode blah 1
(Fo be filed by the Sauder)
“Note: All questions are compulsory.
Part- A
(Questions from Tutorial Sheet) [10 Marks]
~ QI How will you designate alloy steels with following composition-
_ a) Carbon=0,35-0,45%, Chromium=0.90-1.1%
b) Carbon=0.12-0,20%, Nickel=0.80-1.2%, Chromium=0,6-1.0%
{QNo.9}[2.542.5]
ble diameter for a circular shaft required to transmit 90kw at 180 rpm. The sheae stress in the
eed 70 MPa and the maximum torque exceeds the mean by 40%. Also find the angle of
ngth of 2 meters. Take G=90GPa [QNo.8}{3+2]
Part-B (20 Marks}
|
QB. A shaft, as shown in fig is subjected to a bending load of KN, pure torque of 100) Nm and an
axial pulling forte of 15 kN calculate the stressat point A and B. Bi
_ Q4.A pump lever rocking shaft is shown in-figure Below, the pump lever exerts a forces of 25KN and
35KN concentrated at 150 mm and 200 mm from the left and right hand bearing find the diameter of
ica)
the central portion of the shaft if the stress is not to exceed 100 MPa.
a
[eae
ts? Explain in briefTT Academie26
lL ReferVUACAD/
AGEMENT
SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MAN.
B.Tech. [SEM V (ME)]
UIZ TEST-1
2013-14)
(Sess
MACHINE DESIGN-1
Time: I hour (EME-501) Max, marks : 30
Roll No. Cee I
(Fo be filed bythe Suen)
Note: All questions are compulsory.
Part-A
[0 Marks}
(Questions from Tutorial Sheet)
for specification of carbon steels and alloy steels. Write BIS designation of
.e BIS criteria
2,40C1V23,20C4,FeE350
[QNo.3][1424141}
torque T If
Q2. A mild steel of shaft of 50mm diameter is subjecte
of the steel in tension is 200.’MPa, fi
the yield p
ing of the shaft according to The maximum pri
|
Part-B [20 Marks}
3. A shaft, as shown in fig is subjected to a bending load of 3 KN, pure torque of 1000 Nm and an
pulling force of 15 kN calculate the stress at point A and B. (8)
y 3kt
fee pe,
oe =
Aor
ae
$B asp mm
is shown in figure below, the pump lever exerts a forces of 25kN and
Q4. A pump lever rocking shaft i F
‘4-200 mm from the leftand right hand bearing find the diameter of
a
35KN concentrated at 150 mm an
sntral portion of the shaft if the stress is not to exceed 100 MPa.
the cer
sie gowns Stks
fee