Professional Documents
Culture Documents
Grade 10 Exam (January)
Grade 10 Exam (January)
NAME: _____________________
CLASS: ______
ii. Section B:
You are required to answer ALL the True-False items from this section.
iii. Section C:
2. Number and answer according to the numbering system used in the questions.
3. Use sketches when necessary to support yours answers.
4. Only pencils should be used for drawing or sketching.
5. Silent electronic CALCULATORS may be used.
6. ALL students should be in their assigned area until the completion of the EXAM.
7. Write your NAME and CLASS on the spaces provided above.
2
SECTION A: Multiple Choice (30 MARKS)
Instructions:
i.
Each item in this section has four suggested answers lettered (a), (b), (c), (d).
ii.
iii.
Read the following items carefully then circle the LETTER beside the response which
provides the CORRECT answer. Each correct response is worth (1) mark.
Example,
30.
2. Safety gears that should be worn when operating machines in the workshop are:
I.
II.
III.
IV.
Overall/Lab coat.
Goggles.
Ear lid.
Hard shoes.
(A)
(B)
(C)
(D)
I and II only
I, II and IV only
II and IV only
I, II, and III
3. Oily rags or waste can cause fire from spontaneous combustion and should therefore be store:
(A)
(B)
(C)
(D)
Prong.
Frame.
Wing nut.
Tip.
5. Square head, protractor head and centre head are parts of which one of the following
measuring tools?
(A)
(B)
(C)
(D)
Pocket
Set square
Bevel square
Combination square
3
6. Why it is important to always grind off chisel with mushroomed top?
(A)
(B)
(C)
(D)
SECTION B
Hand file.
Triangular file.
Warding file.
square file
Round file.
Half round file.
Warding file.
Oval file.
9. If a machinist wants to file a material that is just being cut by the hacksaw, which of method
of filing should he use first?
(A)
(B)
(C)
(D)
Draw-filing.
Smooth-filing.
Cross-filing.
Rough-filing.
10. Which of the following is the CORRECT tool used to locate centres of holes for drilling?
(A)
(B)
(C)
(D)
Prick punch
Drill point gauge
Centre punch
Pin punch
Excessive tensioning
Insufficient tensioning
Correct tooth size
Stroke out of line
12. If an Engineer wants to cut thread for a nut, what hand tool would the Engineering used?
(A)
(B)
(C)
(D)
Dies
Boring tool
Threading bar
Taps
Blister
Redness
Tissue damage
Epidermis damage
Smoke
Heat
Fuel
Oxygen
I,II, and IV
I,III, and IV
II,III, and IV
I,II, and III
15. What is the name of the tool been used to check the diameter of the work piece.
(A)
(B)
(C)
(D)
Inside Caliper
Odd leg Caliper
Outside Caliper
Vernier Caliper
Cross-filing
Hand-filing
Single-cut filing
Draw-filing
5
Items 17 20 refers to the following one inch scale below.
1/8
1/4
3/8
9/16
(A)
(B)
(C)
(D)
11/16
1/4
5/8
3/4
7/8
3/4
2/8
7/16
5/8
1/4
5/8
13/16
2.5 cm
25.4 cm
2.44 cm
2.4 cm
254 mm
25.5 mm
25 mm
2.55 mm
14 mm
24 mm
12 mm
15 mm
24. Types A fires extinguishers are used to put out fires from which of the following materials:
6
(A)
(B)
(C)
(D)
(A)
(B)
(C)
(D)
27. Which tool is used for drawing lines parallel to a given edge?
Combination set
Engineering level
Try square
Odd-leg caliper
(A)
(B)
(C)
(D)
28. For safety purposes using the drill press and the lathe machine an individual should have the
following protective gears.
I.
II.
III.
IV.
(A)
(B)
(C)
(D)
Cover all
A Pair of Gloves
A Pair of Goggles
Respirator
I and II only
I and III only
II, III, and IV
All of the above
Cross cut
Double cut
Single cut
Rasp cut
30. If an engineer wears goggles, face shield or glasses while operating the grinding machine, it
is because he wants to_________.
(I)
(J)
(K)
(L)
8
SECTION B: True/False (10 marks)
Instructions:
i.
Read each item carefully before deciding if your answer is TRUE or FALSE.
ii.
If the statement is TRUE circle the letter T and if the statement is FALSE circle the
letter F.
Example,
a.
9
SECTION C: Short Answer (45 Marks)
Instructions:
i.
ii.
(3 Marks)
___________________________________________________________________________
___________________________________________________________________________
a. State the use of anyone of the alloying elements listed above.
(2 marks)
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
2. State the three (3) factors that should be considered when selecting a file.
(3 marks)
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
3. Outline the three (3) degrees of burn and give one (1) symptom of each.
(3 marks)
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
4. Differentiate between the following terms:
a) Ferrous and Non-ferrous metal
(3 marks)
___________________________________________________________
___________________________________________________________
___________________________________________________________
___________________________________________________________
b) Scriber and Divider
(3 marks)
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
GO TO THE NEXT PAGE
10
5. Describe the following terms:
a) Malleability.
(3 marks)
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
b)
Elasticity.
(3 marks)
_______________________________________________________________________
_______________________________________________________________________
_______________________________________________________________________
6. List five (5) general safety precautions that should be observed when working in the
workshop.
(5 marks)
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
___________________________________________________________________________
7. Draw a neatly label diagram of a file.
(5 marks)
(3 marks)
11
(3 marks)
b)
(3 marks)
b)
(3 marks)
END OF EXAM
_____________________________________________________________________________